Furuno USA 9ZWRTR107 Transceiver for Radar model FAR-3230S/3330S User Manual

Furuno USA Inc Transceiver for Radar model FAR-3230S/3330S

UserManual.wiki >

9ZWRTR107 User Manual >

Contents

1. User Manual
2. Users Manual

User Manual

OPERATOR'S MANUALwww.furuno.comCHART RADARFAR-3210FAR-3220FAR-3230SFAR-3230S-SSDFAR-3310FAR-3320FAR-3330SFAR-3330S-SSDFAR-3320WFAR-3330SWFAR-3210-BBFAR-3220-BBFAR-3230S-BBFAR-3230S-SSD-BBFAR-3220W-BBFAR-3230SW-BBModel(Product Name: MARINE RADAR)

The paper used in this manualis elemental chlorine free.・FURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPANA:APR2014.Printed in JapanAll rights reserved.B2:DEC.15, 2014Pub. No.OME-36160-B2(YOTA)FAR-3000SERIES 0 0 0 1 7 8 0 2 7 1 1

ii SAFETY INSTRUCTIONS The operator must read the safety instructions before attempting to operate the equipment.The radar antenna emits electromagnetic radio frequency (RF) energy that can be harmful, particularly to your eyes. Never look directly into the antenna aperture from a close distance while the radar is in operation or expose yourself to the transmitting antenna at a close distance. Distances at which RF radiation level of 100, 50 and 10 W/m2 are given in the table below. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.100W/m2Radar modelFAR-3220/FAR-3320/FAR-3220-BBFAR-3210/FAR-3310/FAR-3210-BBFAR-3230S/FAR-3330S/FAR-3230S-BBFAR-3330SW/ FAR-3230SW-BBFAR-3320W/ FAR-3220W-BBTransceiver Magnetron Antenna 10W/m2 50W/m2 Warning, Caution Prohibitive Action Mandatory ActionRadio Frequency Radiation HazardWARNINGCAUTIONWARNINGRTR-105 FNE1201 XN12CFXN20CFXN24CFRTR-106 MG5436 XN12CFXN20CFXN24CFRTR-108 MG5436 XN20CFXN24CFRTR-107 MG5223F SN36CFRTR-109 MG5223F SN36CFMagnetron radar100W/m2Radar modelFAR-3230S-SSD/FAR-3330S-SSD/FAR-3230S-SSD-BBTransceiver Antenna 10W/m2 50W/m2 RTR-111 SN36CFSolid state radarN/AN/A N/A 1.0 m0.5 m 4.6 m0.6 m 1.4 m 4.4 m0.4 m 0.9 m 3.0 m0.3 m 0.6 m 2.5 m1.3 m 2.7 m 9.5 m1.0 m 1.7 m 6.8 m0.7 m 1.3 m 5.5 mN/A 0.26 m 2.3 m0.5 m 1.2 m 5.5 m0.3 m 0.9 m 4.0 m

SAFETY INSTRUCTIONSiiiWARNINGDo not open the equipment.The equipment uses high voltage that can cause electrical shock. Refer any repair work to a qualified technician.Before turning on the radar, be sure no one is near the antenna.Prevent the potential risk of being struck by the rotating antenna, which can result in serious injury or death.If water leaks into the equipment or something is dropped into the equipment, immediately turn off the power at the switchboard.Fire or electrical shock can result.If the equipment is giving off smoke or fire, immediately turn off the power at the switchboard.Fire or electrical shock can result.If you feel the equipment is acting abnormally or giving off strange noises, immediately turn off the power at the switchboard and contact a FURUNO service techni-cian.Do not disassemble or modify the equipment.Fire, electrical shock or serious injury can result.Make sure no rain or water splash leaks into the equipment.Fire or electrical shock can result if water leaks into the equipment.Do not place liquid-filled containers on or near the equipment.Fire or electrical shock can result if a liquid spills into the equipment.Do not operate the equipment with wet hands.Electrical shock can result.Keep objects away from the open-type antenna unit, so as not toimpede rotation of the antenna.Fire, electrical shock or serious injury can result.Use the proper fuse. Use of the wrong fuse can cause fire or damage the equipment.The TT function is a valuable aid to navigation. However, the navigator must check all aids available to avoid collision.- The TT automatically tracks an automatically or manually acquired radar target and calculates its course and speed, indicating them with a vector. Since the data generated by the TT depends on the selected radar targets, the radar must be optimally tuned for use with the TT, to ensure required targets will not be lost or unnecessary targets, like sea returns and noise, will not be acquired and tracked.- A target is not always a landmass, reef, ship, but can also be returns from the sea surface and from clutter. As the level of clutter changes with the environment, the operator must correctly adjust the sea and rain clutter controls and the gain control so that the target echoes do not dis- appear from the radar screen.WARNING WARNING

SAFETY INSTRUCTIONSivThe plotting accuracy and response of this TT meets IMO standards. Tracking accuracy is affected by the following:• Tracking accuracy is affected by course change. One to two minutes is required to restore vectors to full accuracy after an abrupt course change. (The actual amount depends on gyrocompass specifications.)• The amount of tracking delay is inversely proportional to the relative speed of the target. Delay is approx. 15-30 seconds for the higher relative speed; approx. 30-60 seconds for the lower relative speed. The following factors can affect accuracy: - Echo intensity - Radar transmission pulse length - Radar bearing error - Gyrocompass error - Course change (own ship and targets)Handle the LCD carefully.The LCD is made of glass, which can cause injury if broken.The data presented by this equipment is intended as a source of navigation information.The prudent navigator never relies exclusively on any one source of navigation information, for safety of vessel and crew.WARNINGTo avoid electrical shock, do not remove cover. No user-serviceable parts inside.WARNINGRadiation hazard. Only qualified personnel should work inside scanner.Confirm that TX has stopped beforeopening scanner.Name: Warning Label 1Type: 86-003-1011-1Code No.: 100-236-231 Name: Warning StickerType: 03-142-3201-0Code No.: 100-266-890 Warning Label(s) Warning label(s) is(are) attached to the equipment. Do not remove the label(s). If a label is missing or damaged, contact a FURUNO agent or dealer about replacement.CAUTIOCAUTION

TABLE OF CONTENTSvi2. RADAR, CHART RADAR OPERATION................................................................2-12.1 How to Transmit......................................................................................................... 2-12.2 How to Tune the Radar Receiver............................................................................... 2-12.2.1 Tuning for magnetron radar ........................................................................... 2-12.3 Pulse Length .............................................................................................................. 2-22.3.1 How to select a pulse length ..........................................................................2-22.3.2 How to change the pulse length..................................................................... 2-32.4 How to Adjust the Sensitivity...................................................................................... 2-32.5 How to Suppress Sea Clutter..................................................................................... 2-32.5.1 How to reduce sea clutter automatically ........................................................ 2-42.5.2 How to reduce sea clutter manually............................................................... 2-42.6 How to Suppress Rain Clutter.................................................................................... 2-52.6.1 How to reduce rain clutter automatically ........................................................ 2-52.6.2 How to reduce rain clutter manually............................................................... 2-62.7 Interference Rejector.................................................................................................. 2-72.8 Echo Stretch............................................................................................................... 2-72.9 Echo Averaging.......................................................................................................... 2-82.10 Automatic Clutter Elimination (ACE) Function ........................................................... 2-92.10.1 How to turn the Automatic Clutter Elimination (ACE) function on/off .............2-92.10.2 How to adjust the gain in the Automatic Clutter Elimination (ACE) mode...... 2-92.10.3 Automatic Clutter Elimination (ACE) menu .................................................. 2-102.10.4 How to get the high sensitivity...................................................................... 2-102.10.5 How to suppress the false echoes ............................................................... 2-102.11 Noise Rejector.......................................................................................................... 2-112.12 Wiper........................................................................................................................2-122.13 How to Preset Controls for Specific Navigation Purpose ......................................... 2-122.13.1 How to select a customized echo................................................................. 2-142.13.2 How to edit a customized echo .................................................................... 2-142.13.3 How to restore a user customized echo to the saved settings.....................2-152.13.4 How to restore a user customized echo to the factory default settings........ 2-152.14 How to Suppress Second-trace Echoes ..................................................................2-162.15 Presentation Modes ................................................................................................. 2-162.15.1 How to select a presentation mode.............................................................. 2-172.15.2 Description of presentation modes............................................................... 2-182.16 How to Select the Range Scale ............................................................................... 2-202.17 How to Measure the Range to a Target ................................................................... 2-202.17.1 How to measure the range by using a VRM ................................................2-212.17.2 How to set VRM attributes ........................................................................... 2-222.18 How to Measure the Bearing to a Target ................................................................. 2-232.18.1 How to measure the bearing........................................................................ 2-232.18.2 How to select bearing reference ..................................................................2-242.19 Collision Assessment by Offset EBL........................................................................ 2-242.19.1 How to assess risk of collision .................................................................... 2-242.19.2 Point of reference for origin point of offset EBL ........................................... 2-252.20 How to Measure the Range and Bearing Between Two Targets............................. 2-262.21 How to Off-center the Display .................................................................................. 2-272.22 Target Trails............................................................................................................. 2-282.22.1 Target trails-related indications.................................................................... 2-282.22.2 True or relative target trails .......................................................................... 2-282.22.3 Trail time ...................................................................................................... 2-292.22.4 How to reset target trails .............................................................................. 2-292.22.5 How to temporarily remove all target trails from the display ........................ 2-292.22.6 Trail stabilization in true motion.................................................................... 2-292.22.7 Target trail attributes on the TRAIL menu .................................................... 2-302.23 Parallel Index (PI) Lines ........................................................................................... 2-302.23.1 How to display, erase a PI line..................................................................... 2-31

TABLE OF CONTENTSvii2.23.2 How to adjust PI line orientation, PI line interval ..........................................2-312.23.3 How to select the number of PI lines to display............................................2-312.23.4 How to select the bearing reference for the PI line ......................................2-312.23.5 How to select the PI lines orientation ...........................................................2-322.23.6 How to reset PI lines ....................................................................................2-322.23.7 How to adjust PI line length..........................................................................2-322.24 Zoom ........................................................................................................................2-332.25 Markers.....................................................................................................................2-342.25.1 Heading line .................................................................................................2-342.25.2 Stern marker.................................................................................................2-342.25.3 North marker ................................................................................................2-342.25.4 Own ship marker ..........................................................................................2-342.25.5 Vectors .........................................................................................................2-352.25.6 Barge marker................................................................................................2-352.25.7 Antenna marker............................................................................................2-362.25.8 Cursor...........................................................................................................2-362.26 How to Adjust Brilliance of Screen Data...................................................................2-372.27 Watch Alert...............................................................................................................2-382.28 Information Box ........................................................................................................2-392.28.1 Information box contents ..............................................................................2-392.28.2 How to show the information box .................................................................2-402.28.3 How to turn NAV data on/off.........................................................................2-412.29 Interswitch ................................................................................................................2-422.29.1 Displaying antenna information ....................................................................2-422.29.2 How to preset antenna and display combinations........................................2-432.29.3 How to select an antenna.............................................................................2-442.30 Dual Radar (B-type only)..........................................................................................2-452.30.1 How to enable or disable the dual radar display ..........................................2-462.30.2 Operating considerations for the dual radar display.....................................2-462.31 Performance Monitor................................................................................................2-482.32 Magnetron Reset (For A- and B-types) ....................................................................2-502.33 CCRP (Common Consistent Reference Point).........................................................2-512.34 Drop Mark.................................................................................................................2-532.34.1 How to show, hide the drop mark box ..........................................................2-532.34.2 How to inscribe a drop mark.........................................................................2-532.34.3 Drop mark bearing reference .......................................................................2-532.34.4 How to erase a drop mark ............................................................................2-542.35 Anchor Watch ...........................................................................................................2-542.36 SART ........................................................................................................................2-552.36.1 What is an SART?........................................................................................2-552.36.2 How to receive an SART ..............................................................................2-552.37 Alert Box, Alert List...................................................................................................2-562.37.1 Alert box .......................................................................................................2-562.37.2 Alert list.........................................................................................................2-572.37.3 Changing priority of primary alerts ...............................................................2-572.38 Echo Area.................................................................................................................2-582.39 Echo Color................................................................................................................2-582.40 Icing Prevention........................................................................................................2-592.41 Chart Radar Functions .............................................................................................2-602.41.1 How to switch between radar and chart radar modes ..................................2-602.41.2 How to show or hide chart objects ...............................................................2-602.41.3 How to create and recall custom sets of chart display objects.....................2-622.41.4 Chart database information ..........................................................................2-632.41.5 Chart scale indications .................................................................................2-632.41.6 Chart status ..................................................................................................2-632.41.7 Chart alert function .......................................................................................2-64

TABLE OF CONTENTSviii2.41.8 Notes details ................................................................................................ 2-642.42 Radar Observation ...................................................................................................2-652.42.1 General ........................................................................................................ 2-652.42.2 False echoes................................................................................................2-662.42.3 RACON ........................................................................................................ 2-682.42.4 Radar Target Enhancer (RTE).....................................................................2-682.42.5 Solid state radar...........................................................................................2-693. TARGET TRACKING (TT) .....................................................................................3-13.1 About TT ....................................................................................................................3-13.2 How to Show, Hide the TT Display ............................................................................ 3-13.3 How to Input Your Ship's Speed ................................................................................ 3-23.3.1 Echo-referenced speed input......................................................................... 3-23.4 Automatic Acquisition................................................................................................. 3-33.4.1 How to enable auto acquisition ......................................................................3-33.4.2 How to set an automatic acquisition zone...................................................... 3-43.5 Manual Acquisition ..................................................................................................... 3-53.5.1 How to set manual acquisition conditions ......................................................3-53.5.2 How to manually acquire a target................................................................... 3-63.6 How to Stop Tracking Targets (including reference targets)...................................... 3-63.6.1 How to cancel tracking on individual tracked targets ..................................... 3-63.6.2 How to cancel tracking on all TTs .................................................................. 3-73.7 TT Symbols and TT Symbol Attributes ...................................................................... 3-73.7.1 TT symbols..................................................................................................... 3-73.7.2 TT symbol brilliance ....................................................................................... 3-83.7.3 Color for TT symbol........................................................................................ 3-83.8 How to Display TT Data ............................................................................................. 3-93.8.1 How to display target data for individual TT ................................................... 3-93.8.2 TT pop-up information..................................................................................3-103.8.3 Target list ..................................................................................................... 3-103.9 Vector Modes...........................................................................................................3-113.9.1 Description of vectors................................................................................... 3-113.9.2 Vector motion and length .............................................................................3-133.10 Past Position Display ............................................................................................... 3-133.10.1 How to enable/disable the past position display,select past position reference ...................................................................... 3-143.10.2 Past position points ...................................................................................... 3-143.11 How to Enter Set and Drift .......................................................................................3-143.12 TT CPA/TCPA Alarm ............................................................................................... 3-163.12.1 How to set the CPA and TCPA limits...........................................................3-163.12.2 How to enable, disable the TT CPA/TCPA alarm ........................................3-163.12.3 How to acknowledge the TT CPA/TCPA alarm............................................3-163.13 TT Lost Target Alert ................................................................................................. 3-173.13.1 How to enable, disable the TT lost target alert............................................. 3-173.13.2 How to set the TT lost target filter ................................................................ 3-173.14 Trial Maneuver ......................................................................................................... 3-183.14.1 Types of trial maneuvers.............................................................................. 3-183.14.2 How to do a trial maneuver ..........................................................................3-193.15 TT Simulation Mode ................................................................................................. 3-203.16 TT Alerts...................................................................................................................3-213.17 Criteria for Selecting Targets for Tracking ............................................................... 3-223.18 Factors Affecting Target Tracking ............................................................................ 3-244. AIS OPERATION ...................................................................................................4-14.1 How to Deactivate the AIS Function .......................................................................... 4-24.2 How to Show, Hide the AIS Display ........................................................................... 4-3

TABLE OF CONTENTSix4.3 AIS Symbols...............................................................................................................4-34.4 How to Filter Sleeping AIS Targets ............................................................................4-54.5 How to Activate Targets .............................................................................................4-54.5.1 How to activate specific target........................................................................4-54.5.2 How to automatically activate targets.............................................................4-64.6 How to Sleep Targets .................................................................................................4-64.6.1 How to sleep an activated AIS target .............................................................4-64.6.2 How to sleep all activated AIS targets............................................................4-74.7 How to Display AIS Target Data.................................................................................4-74.7.1 AIS pop-up information...................................................................................4-74.7.2 Basic AIS target data......................................................................................4-74.7.3 Expanded AIS data ........................................................................................4-94.8 AIS CPA/TCPA Alarm ..............................................................................................4-104.9 AIS Symbol Brilliance ...............................................................................................4-104.10 AIS Symbol Color .....................................................................................................4-114.11 AIS Lost Targets.......................................................................................................4-114.11.1 How to enable, disable the AIS lost target alert ...........................................4-114.11.2 How to set the AIS lost target filter ...............................................................4-124.12 How to Display AIS Target Past Positions................................................................4-124.12.1 How to enable/disable the past position display,select past position reference.......................................................................4-124.12.2 Past position points ......................................................................................4-134.13 How to Display True or Relative Speed Vectors ......................................................4-134.14 Association of TT and AIS Targets...........................................................................4-134.14.1 How to select association method................................................................4-134.14.2 How to set the conditions for association .....................................................4-144.15 Voyage Data.............................................................................................................4-144.16 AIS Messages ..........................................................................................................4-154.16.1 How to create and transmit a new AIS message .........................................4-154.16.2 How to transmit a saved AIS message ........................................................4-164.16.3 How to display received AIS messages .......................................................4-164.17 Other AIS Features...................................................................................................4-185. RADAR MAP AND TRACK ...................................................................................5-15.1 What is a Radar Map?................................................................................................5-15.2 Presentation Modes....................................................................................................5-15.3 How to Show, Hide the Radar Map Display ...............................................................5-15.4 How to Enter Radar Map Marks and Lines.................................................................5-25.5 How to Find Number of Map Points Used ..................................................................5-35.6 How to Select the Radar Map to Display....................................................................5-45.7 How to Attach a Comment to a Radar Map, Find Comment for a Map......................5-45.7.1 How to attach a comment to a radar map ......................................................5-45.7.2 How to find the comment for a map ...............................................................5-45.8 How to Erase Radar Map Marks and Lines................................................................5-55.8.1 How to erase individual radar map marks and lines.......................................5-55.8.2 How to erase map marks and lines in an area ...............................................5-55.8.3 How to erase all radar map marks and lines in a map file..............................5-65.9 How to Copy Radar Map Marks and Lines.................................................................5-75.9.1 How to copy individual radar map mark and line to another map file.............5-75.9.2 How to copy radar map marks and lines within an area to another map file..5-75.9.3 How to copy all radar map marks and lines in a map file to another map file 5-85.10 How to Export Radar Map ..........................................................................................5-95.11 How to Import Radar Map ........................................................................................5-105.12 How to Show, Hide Radar Map Features.................................................................5-135.13 Track.........................................................................................................................5-135.13.1 How to set up ship's track.............................................................................5-13

TABLE OF CONTENTSx5.13.2 How to erase track ....................................................................................... 5-145.14 Route Display........................................................................................................... 5-145.15 User Chart Display ................................................................................................... 5-156. CHART OVERVIEW...............................................................................................6-16.1 Chart Screen Overview .............................................................................................. 6-16.1.1 Electronic chart area ...................................................................................... 6-26.1.2 Status bar....................................................................................................... 6-36.1.3 InstantAccess bar........................................................................................... 6-56.1.4 Sensor information box .................................................................................. 6-86.1.5 Own ship functions box.................................................................................. 6-86.1.6 Route information box.................................................................................... 6-96.1.7 Overlay/NAV Tools box................................................................................ 6-106.1.8 Alert box....................................................................................................... 6-106.1.9 Permanent warning box ............................................................................... 6-106.1.10 EBL, VRM boxes.......................................................................................... 6-106.1.11 Context-sensitive menus.............................................................................. 6-116.1.12 How to enter alphanumeric data ..................................................................6-126.2 How to Select the Operating Mode .......................................................................... 6-136.3 How to Select the Chart Operating Mode ................................................................ 6-136.4 How to Select the Chart Scale ................................................................................. 6-146.5 How to Select the Presentation Mode...................................................................... 6-156.6 Cursor Position Box ................................................................................................. 6-166.7 The Standby Mode...................................................................................................6-166.8 True Motion Reset.................................................................................................... 6-176.9 How to Control Route and User Charts in Voyage Navigationand Voyage Planning Modes ...................................................................................6-186.10 How to Use the VRM and EBL.................................................................................6-196.10.1 How to hide/show an EBL, VRM.................................................................. 6-196.10.2 How to measure the range and bearing.......................................................6-196.10.3 How to select bearing reference ..................................................................6-196.10.4 EBL, VRM functions available with the context-sensitive menu...................6-206.11 Split Screen.............................................................................................................. 6-216.12 Datum.......................................................................................................................6-216.12.1 General ........................................................................................................ 6-216.12.2 Paper charts.................................................................................................6-216.12.3 Electronic sea charts.................................................................................... 6-216.12.4 Positioning devices and datum ....................................................................6-216.12.5 Chart radar and datum.................................................................................6-216.13 How to Select Sensor Settings................................................................................. 6-226.14 How to Enter Ship Speed.........................................................................................6-226.15 How to Enter Heading.............................................................................................. 6-246.16 Set up Before Departure .......................................................................................... 6-266.16.1 Updates before departure ............................................................................ 6-266.16.2 Create or update a route..............................................................................6-276.16.3 How to check and prepare route to monitor................................................. 6-286.16.4 Check configuration of navigation sensors .................................................. 6-306.16.5 How to reset odometer and trip meter..........................................................6-317. HOW TO MANAGE CHARTS ................................................................................7-17.1 How to Install Public Keys for ENC Charts ................................................................ 7-17.2 How to Install ENC Licenses, Charts ......................................................................... 7-27.2.1 How to install an ENC license........................................................................ 7-27.2.2 How to install ENC charts .............................................................................. 7-37.3 How to Delete ENC Licenses..................................................................................... 7-57.4 How to Install C-MAP Charts ..................................................................................... 7-6

TABLE OF CONTENTSxi7.4.1 How to register the eToken ............................................................................7-67.4.2 How to install the C-MAP database................................................................7-67.4.3 How to install C-MAP licenses .......................................................................7-87.4.4 How to generate and order an update file ......................................................7-97.4.5 How to apply the update file...........................................................................7-97.5 How to Delete a C-MAP Database.............................................................................7-97.6 How to Install C-MAP DL (Dynamic Licensing) Charts.............................................7-107.6.1 How to generate and order an update file ....................................................7-107.6.2 How to apply the update file.........................................................................7-107.6.3 How to enable and set up the C-MAP DL ....................................................7-117.7 How to Export a List of Charts..................................................................................7-117.8 How to Export a List of Specific Licenses.................................................................7-127.9 How to Show the ENC Permit ..................................................................................7-127.10 How to Backup, Restore Licenses............................................................................7-127.11 How to View Permit Expiration Date.........................................................................7-137.12 How to Display Install/Update History ......................................................................7-147.13 Catalog of Chart Cells ..............................................................................................7-157.13.1 How to group chart cells...............................................................................7-167.13.2 How to view status of chart cells ..................................................................7-187.14 How to Open Charts.................................................................................................7-187.15 How to Print Chart List, Cell Status List....................................................................7-197.15.1 How to print the chart list..............................................................................7-197.15.2 How to print the cell status list......................................................................7-207.16 How to Delete Charts ...............................................................................................7-207.17 How to Show Publishers Notes for ENC Charts.......................................................7-217.18 How to Find the Chart Type......................................................................................7-227.19 How to Update ENC, C-MAP Charts Manually.........................................................7-227.19.1 How to insert update symbols ......................................................................7-237.19.2 How to delete update symbols .....................................................................7-247.19.3 How to modify existing update symbols .......................................................7-247.20 How to Synchronize Chart Data ...............................................................................7-257.20.1 How to select the units to synchronize .........................................................7-257.20.2 How to check synchronization status ...........................................................7-267.20.3 Manual updates and synchronization...........................................................7-277.21 How to Reconvert All SENC Charts .........................................................................7-278. HOW TO CONTROL CHART OBJECTS ..............................................................8-18.1 How to Browse Your Charts .......................................................................................8-18.2 How to Control Visibility of Chart Objects...................................................................8-18.2.1 How to set value for shallow contour, safety depth, safety contourand deep contour ...........................................................................................8-18.2.2 Basic Setting menu ........................................................................................8-38.2.3 Chart Display menu........................................................................................8-48.2.4 Display base...................................................................................................8-58.3 How to Control Visibility of Symbols, Features...........................................................8-58.3.1 General page..................................................................................................8-58.3.2 Tracking page.................................................................................................8-78.3.3 Route page.....................................................................................................8-88.3.4 Mariner page ..................................................................................................8-88.3.5 Targets page ..................................................................................................8-98.4 Control of Predefined IMO Chart Display Settings ...................................................8-109. VECTOR (S57) CHARTS.......................................................................................9-19.1 Introduction to S57 Charts..........................................................................................9-19.1.1 Definitions of terms.........................................................................................9-29.1.2 Chart legend for S57 charts ...........................................................................9-2

TABLE OF CONTENTSxii9.1.3 Permanent warnings for S57 charts............................................................... 9-39.2 Chart Viewing Dates and Seasonal Features of the S57 Chart ................................. 9-49.2.1 Introduction .................................................................................................... 9-49.2.2 How to approve and highlight S57 chart updates .......................................... 9-49.2.3 How to set Display date and Approved until dates......................................... 9-59.2.4 About chart viewing date dependency of S57 standard................................. 9-59.3 Symbology Used in S57 Charts ................................................................................. 9-69.3.1 Presentation library used for S57 chart features............................................ 9-69.4 How to Find Information About S57 Chart Objects .................................................... 9-79.5 Admiralty Information Overlay (AIO) .......................................................................... 9-89.5.1 Installation ...................................................................................................... 9-89.5.2 How to display the AIO................................................................................... 9-89.5.3 Catalog of AIO cells ....................................................................................... 9-99.5.4 How to find AIO chart object information........................................................ 9-99.5.5 How to select the information to display....................................................... 9-1010. C-MAP CHARTS..................................................................................................10-110.1 C-MAP Cartographic Service...................................................................................10-110.2 How to Register the System at C-MAP Norway....................................................... 10-110.3 How to Order Charts ................................................................................................ 10-110.4 How to Apply for Licenses........................................................................................ 10-110.5 Troubleshooting ....................................................................................................... 10-210.6 Chart Subscription Services..................................................................................... 10-210.6.1 C-MAP services ........................................................................................... 10-210.6.2 What is ENC delivery? ................................................................................. 10-210.7 Chart Display............................................................................................................ 10-310.7.1 Introduction .................................................................................................. 10-310.8 Permanent Warnings ...............................................................................................10-411. CHART ALERTS..................................................................................................11-111.1 Chart Alerts .............................................................................................................. 11-211.1.1 How to set safety contour............................................................................. 11-211.1.2 How to select objects used in chart alerts.................................................... 11-311.2 How to Activate Own Ship Check ............................................................................ 11-411.3 Route Planning.........................................................................................................11-511.3.1 Chart alerts for route planning...................................................................... 11-511.4 Route Monitoring...................................................................................................... 11-712. ROUTES...............................................................................................................12-112.1 Route Planning Overview.........................................................................................12-112.2 Main Menu for Route Planning.................................................................................12-212.3 How to Create a New Route .................................................................................... 12-212.3.1 How to use the Waypoints page ..................................................................12-412.3.2 How to use the User Chart page..................................................................12-512.3.3 How to use the Optimize page..................................................................... 12-612.3.4 How to use the Alert Parameters page ........................................................ 12-612.3.5 How to use the Check Results page ............................................................ 12-812.4 How to Modify an Existing Route ............................................................................. 12-812.4.1 How to change waypoint position................................................................. 12-812.4.2 How to change other waypoint data.............................................................12-912.4.3 How to add a new waypoint at the end of a route........................................12-912.4.4 How to insert a waypoint.............................................................................. 12-912.4.5 How to delete a waypoint ............................................................................. 12-912.4.6 Geometry check of route............................................................................ 12-1012.5 SAR Operations ..................................................................................................... 12-1012.6 Route Bank ............................................................................................................ 12-13

TABLE OF CONTENTSxiv15.5 Predictor...................................................................................................................15-515.6 Anchor Watch........................................................................................................... 15-615.7 UKC (Under Keel Clearance)...................................................................................15-715.7.1 UKC overview .............................................................................................. 15-715.7.2 How to set UKC............................................................................................ 15-715.7.3 UKC window................................................................................................. 15-815.8 Mini Conning Display ............................................................................................... 15-915.9 Divider .................................................................................................................... 15-1015.9.1 How to use the divider................................................................................ 15-1015.9.2 Usage characteristics, limitations............................................................... 15-1115.9.3 How to deactivate and erase the divider....................................................15-1116. NAVIGATION SENSORS.....................................................................................16-116.1 CCRS.......................................................................................................................16-116.2 How to Select Navigation Sensors........................................................................... 16-216.2.1 Sensors menu description............................................................................16-216.3 Source of Position .................................................................................................... 16-616.4 Primary and Secondary Positions of Own Ship .......................................................16-716.5 Source of Navigation Data ....................................................................................... 16-816.6 Switching of Sensor and Indication ........................................................................16-1016.7 Filter Status ............................................................................................................ 16-1016.8 Position Alignment ................................................................................................. 16-1216.8.1 How to align position.................................................................................. 16-1216.8.2 How to cancel position alignment............................................................... 16-1316.9 Wind Sensor........................................................................................................... 16-1316.10Depth Sensor......................................................................................................... 16-1417. AIS SAFETY, NAVTEX MESSAGES...................................................................17-117.1 AIS Safety Messages............................................................................................... 17-117.1.1 How to send an AIS safety message ...........................................................17-117.1.2 How to display received and sent AIS safety messages.............................. 17-217.1.3 How to delete received and sent AIS safety messages ............................... 17-317.2 Navtex Messages.....................................................................................................17-317.2.1 How to receive Navtex messages................................................................17-317.2.2 How to delete received Navtex messages ................................................... 17-418. TT AND AIS DISPLAYS.......................................................................................18-118.1 TT Display ................................................................................................................ 18-118.1.1 TT symbols................................................................................................... 18-118.1.2 TT symbol color and size ............................................................................. 18-118.1.3 How to display tracked target data............................................................... 18-218.1.4 Past position point attributes........................................................................ 18-318.1.5 How to set the TT lost target filter ................................................................ 18-318.1.6 TT recording functions ................................................................................. 18-318.2 AIS Display............................................................................................................... 18-418.2.1 AIS symbols ................................................................................................. 18-418.2.2 Voyage data................................................................................................. 18-418.2.3 How to filter AIS targets ............................................................................... 18-518.2.4 How to set conditions for automatic activation of sleeping targets...............18-518.2.5 How to sleep all activated targets ................................................................ 18-618.2.6 How to set the AIS lost target filter............................................................... 18-618.2.7 How to display AIS target data..................................................................... 18-718.2.8 How to display own ship data....................................................................... 18-918.3 Association............................................................................................................... 18-918.3.1 How to select association method................................................................18-918.3.2 How to set the conditions for association...................................................18-10

TABLE OF CONTENTSxv19. RECORDING FUNCTIONS .................................................................................19-119.1 How to Record User, Position Events ......................................................................19-119.1.1 User events ..................................................................................................19-119.1.2 Position events .............................................................................................19-219.2 Details Log................................................................................................................19-519.3 Voyage Log ..............................................................................................................19-619.3.1 How to set conditions of logging...................................................................19-819.4 Chart Usage Log ......................................................................................................19-819.5 Danger Targets Log................................................................................................19-1019.5.1 How to set the conditions for logging danger targets .................................19-1120. ALERTS ...............................................................................................................20-120.1 What is an Alert? ......................................................................................................20-120.2 Alert Box...................................................................................................................20-220.3 How to Temporarily Silence the Buzzer for an Alarm or Warning ............................20-520.4 How to Acknowledge an Alarm or Warning..............................................................20-520.5 Alert List....................................................................................................................20-620.6 Alert Log ...................................................................................................................20-720.7 Alert Reception from Connected Sensors ................................................................20-820.8 List of Alerts..............................................................................................................20-821. PARAMETERS ....................................................................................................21-121.1 Ship and Route Parameters .....................................................................................21-121.2 Instant Track Parameters .........................................................................................21-221.3 Cost Parameters.......................................................................................................21-322. SETTINGS MENU................................................................................................22-122.1 How to Access the Settings Menu............................................................................22-122.2 File Export ................................................................................................................22-222.3 File Import.................................................................................................................22-322.4 File Maintenance ......................................................................................................22-422.5 Self Test ...................................................................................................................22-522.6 Data Sharing.............................................................................................................22-622.7 Customize.................................................................................................................22-722.8 Display Test..............................................................................................................22-822.9 Keyboard Test ..........................................................................................................22-922.10Screenshots...........................................................................................................22-1122.10.1How to export screenshots.........................................................................22-1222.10.2How to delete screenshots .........................................................................22-1222.11User Default...........................................................................................................22-1322.12CCRP.....................................................................................................................22-1423. COMMON REFERENCE SYSTEM......................................................................23-123.1 Installation of the System .........................................................................................23-123.2 Accuracy of the System............................................................................................23-124. MAINTENANCE AND TROUBLESHOOTING.....................................................24-124.1 Maintenance.............................................................................................................24-224.2 How to Replace the Fuses .......................................................................................24-324.3 Trackball Maintenance .............................................................................................24-424.4 How to Clean the Filter in the Processor Unit...........................................................24-424.5 Troubleshooting........................................................................................................24-524.6 Consumable Parts ....................................................................................................24-724.7 Color Differentiation Test for S57 Charts..................................................................24-824.8 Fallback Arrangements.............................................................................................24-9

TABLE OF CONTENTSxviAPPENDIX 1 MENU TREE .......................................................................................AP-1APPENDIX 2 ABBREVIATIONS, SYMBOLS ...........................................................AP-9APPENDIX 3 DATA COLOR AND MEANING........................................................AP-22SPECIFICATIONS .....................................................................................................SP-1INDEX.......................................................................................................................... IN-1

xviiFOREWORDCongratulations on your choice of the FURUNO FAR-3xx0 Series Marine Radar. We are confident you will see why the FURUNO name has become synonymous with quality and reliability.Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our ex-tensive global network of agents and dealers.This equipment is designed and constructed to meet the rigorous demands of the marine environ-ment. However, no machine can perform its intended function unless installed, operated and maintained properly. Please carefully read and follow the recommended procedures for operation and maintenance.FeaturesThis radar series meets the requirements of IEC 62388 (Marine navigation and radiocommunica-tion equipment and systems - Shipborne radar - Performance requirements, method of testing and required test results) and IMO MSC.192(79), IMO Resolution A.817(19), and IEC 61174. This ra-dar displays radar targets, electronic charts, nav lines, Tracked Target (TT) data, AIS targets and other navigation data on a display.The main features of this series are• The FAR-3xx0 series consists of the following models and configurations:Magnetron radarSolid state radar*: Viewing distance: 1020 mmModel Frequency bandSize ofmonitor unit*Output powerTransceiver locationFAR-3210X-band19.0” 12 kW Antenna unitFAR-3210-BB Local supply 12 kW Antenna unitFAR-3310 23.1” 12 kW Antenna unitFAR-3220 19.0” 25 kW Antenna unitFAR-3220-BB Local supply 25 kW Antenna unitFAR-3320 23.1” 25 kW Antenna unitFAR-3320W 23.1” 25 kW Transceiver unitFAR-3220W-BB Local supply 25 kW Transceiver unitFAR-3230SS-band19.0” 30 kW Antenna unitFAR-3230S-BB Local supply 30 kW Antenna unitFAR-3330S 23.1” 30 kW Antenna unitFAR-3330SW 23.1” 30 kW Transceiver unitFAR-3230SW-BB Local supply 30 kW Transceiver unitModel Frequency bandSize ofmonitor unit*Output powerTransceiver locationFAR-3230S-SSDS-band19.0” 250 W Antenna unitFAR-3330S-SSD 23.1” 250 W Antenna unitFAR-3230S-SSD-BB Local supply 250 W Antenna unit

FOREWORDxviii• New HMI (Human Machine Interface) gives improved operability.• Accepts SXGA, UXGA video inputs.• SOLAS category 1 compatible display (23.1”), SOLAS category 2 compatible display (19.0”).• Radar, chart and chart radar modes. (The chart radar mode does not meet the criteria for nav-igation aid for Japanese flag vessels as defined by Japanese law.)• Many warning features to support safer and more efficient navigation.• Grounding warnings, safe depth contours.• Chart database loaded and updated using CD-ROMs.• Tracked Target (TT) data and AIS data to aid in collision avoidance.• AIS messaging.• Route created in chart mode can be displayed on the radar.• Route planning and route monitoring facilities in the chart mode.Signal Processing FunctionsThis radar has the signal processing functions described in the table below. All signal processing functions are set with the picture preset feature.Standards Used in this Manual• Three types of Control Units are available: Radar Control Unit RCU-025 (radar controls with trackball module), ECDIS Control Unit RCU-024 (alphabet keyboard, controls, trackball mod-ule) and Trackball Control Unit RCU-026 (trackball module only). Unless noted otherwise, “Con-trol Unit” refers to the RCU-025.• The system can be operated with the controls of the Radar Control Unit, ECDIS Control Unit or a trackball module. The descriptions in this manual use the trackball module.• Unless noted otherwise, "click" means to push the left button on a trackball module.• The keys and controls of the Radar Control Unit are shown in bold face; for example, the EN-TER key. Signal processing function Description SectionInterference rejector Suppress interference transmitted by other radars. Inter-ference received simultaneously from many radars can be difficult to reduce.2.7Echo stretch Enlarge target echoes, especially small echoes. Sup-press interference, sea clutter and rain clutter before us-ing echo stretch, to prevent the enlargement of unwanted echoes.2.8Echo averaging The radar samples echoes with each scan. Targets that show a large change with each scan are judged as clutter and are reduced to display only echoes from legitimate targets.2.9Automatic clutter elimination Discriminate the clutter from the radar echo then reduce the clutter automatically.2.10Noise rejector Reduce the white noise then improves the on-screen S/N ratio by processing the weighted moving average filter for the received echoes in the range direction. Use this func-tion with caution. Weak target echoes may disappear from the screen or the range resolution may worsen.2.11

FOREWORDxix• The buttons on the InstantAccess bar, Status bar and menu items are shown in brackets; for example, the [TUNE] button.• Context-sensitive menus are available with many buttons, and boxes and objects. Right-click an item to display the related context-sensitive menu.• This radar is available in three types of specifications: IMO, A, or B. This manual provides the descriptions for the B type, of which some functions are not available with the IMO or A type. See the menu tree in Appendix 1 for function availability.• “C-MAP” means “C-MAP by Jeppesen”.• The display colors mentioned in this manual are those with the color palette setting “Day-Gray”.Program NumberPlease access the following URL if you need software information:http://www.furuno.com/en/business_product/merchant/product/chartradar/software.htmlxx: Minor changeVirus PreventionThis equipment is not equipped with a virus checker. This equipment operates in real time; there-fore, having a virus checker that periodically checks the equipment for viruses would increase the processing load, which can affect operation. However, you can avoid viruses by following the in-structions in this section. When you update a chartThe PC and medium (USB flash memory, etc.) used to download and store an update for an ex-isting chart or a new chart may be infected with a virus. Check the PC and the medium for viruses with a commercial virus checker - BEFORE you connect them to the ECDIS. Be sure the virus checker contains the latest virus definition files. Network connectionThe ECDIS receives and displays information from various navigation equipment and radar via a LAN. A PC and other equipment connected to a network can carry viruses. To prevent the intro-duction of a virus to the LAN, DO NOT connect the ECDIS or HUB to an external network, includ-ing other shipboard LAN.Do not install 3rd party programs in the ECDISPrograms installed via an external network can carry viruses that can cause the ECDIS to mal-function. Do not install any Windows® software.System Program no. Version no. RemarksAntenna unitSPU 0359281 01.xx For magnetron radarSPU 0359286 01.xx For solid state radarMTR-DRV 0359293 01.xxPM 0359296 01.xxRF-Converter 0359302 01.xx For solid state radarPower supply unitPSU-Control 0359299 01.xxProcessor Unit: EC-3000Main 0359266 02.xx

FOREWORDxxOpen Source SoftwareThis product includes software to be licensed under the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), BSD, Apache, MIT and others. The program(s) is/are free software(s), and you can copy it and/or redistribute it and/or modify it under the terms of the GPL or LGPL as published by the Free Software Foundation. Please access to the following URL if you need source codes: https://www.furuno.co.jp/cgi/cnt_oss_e01.cgiThis product uses the software module that was developed by the Independent JPEG Group.Reverse engineeringReverse engineering (reverse assemble, reverse compiler) of the software of this equipment is prohibited.

xxiSYSTEM CONFIGURATIONSBasic configuration is shown with solid line.FAR-3210/FAR-3220/FAR-3310/FAR-3320/FAR-3210-BB/FAR-3220-BBNOTICEThe radar(s) must be interconnected to the following type approved sensors: Gyrocompass meeting the requirements of the IMO resolution A.424(XI). EPFS meeting the requirements of the IMO resolution MSC.112(73). SDME meeting the requirements of IMO resolution MSC.96(72).The radar may be interconnected via HUB-3000 to other FURUNO processing units having approved LAN ports.100-115/220-230 VAC1ø, 50-60 HzPSU-014 POWER SUPPLY UNITEC-3000PROCESSOR UNITSerial 1, 2IEC 61162-2(Gyrocompass*1, AIS)Serial 3 - 7 IEC 61162-1(EPFS*2 (Navigator), SDME (Speed Log), Echo Sounder, Wind, Alarm*5, Navtex, etc.)Digital Out 1 - 6*51: System Fail2: Power Fail3: Normal Close 14: Normal Close 25: Normal Open 16: Normal Open 2100-230 VAC 1ø, 50-60 HzTransformer RU-1803440 VAC 1ø, 50-60 HzSensor Adapter*4 or Switching HUBHUB-100ANTENNA UNIT(w/Performance Monitor PM-32A)XN12CF-RSB-128XN20CF-RSB-128XN24CF-RSB-128TRANSCEIVER UNITRTR-105 (12 kW)RTR-106 (25 kW)Sub displayLAN SerialSelect oneSelect oneSelect one100-115/220-230 VAC 1ø, 50-60 Hz(for de-icer)Radar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026Monitor Unit MU-190*3 MU-231*3Digital In (ACK IN)VDRIntelligent Hub HUB-3000*: See the notes on page xxvi.Junction box*6 RJB-001Junction box*6 RJB-001

SYSTEM CONFIGURATIONSxxiiFAR-3320W/FAR-3220W-BB100-115/220-230 VAC1ø, 50-60 HzSerial 1, 2IEC 61162-2(Gyrocompass*1, AIS)Serial 3 - 7 IEC 61162-1(EPFS*2 (Navigator), SDME (Speed Log), Echo Sounder, Wind, Alarm*5, Navtex, etc.)Digital Out 1 - 6*51: System Fail2: Power Fail3: Normal Close 14: Normal Close 25: Normal Open 16: Normal Open 2100-230 VAC 1ø, 50-60 HzTransformer RU-1803440 VAC 1ø, 50-60 HzSensor Adapter*4 or Switching HUBHUB-100ANTENNA UNIT (w/Performance Monitor PM-32A)XN20CF-RSB-130XN24CF-RSB-130Sub displayEC-3000PROCESSOR UNITPSU-014POWER SUPPLY UNITLAN SerialSelect oneSelect oneSelect oneTRANSCEIVER UNITRTR-108100-115/220-230 VAC 1ø, 50-60 Hz (for de-icer)WaveguideAntenna CableRadar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026Monitor Unit MU-231*3Digital In (ACK IN)VDRIntelligent Hub HUB-3000*: See the notes on page xxvi.

SYSTEM CONFIGURATIONSxxiiiFAR-3230S/FAR-3330S/FAR-3230S-BB100-115/220-230 VAC1ø, 50-60 HzEC-3000PROCESSOR UNITSerial 1, 2IEC 61162-2(Gyrocompass*1, AIS)Serial 3 - 7 IEC 61162-1(EPFS*2 (Navigator), SDME (Speed Log), Echo Sounder, Wind, Alarm*5, Navtex, etc.)Digital Out 1 - 6*51: System Fail2: Power Fail3: Normal Close 14: Normal Close 25: Normal Open 16: Normal Open 2100-230 VAC 1ø, 50-60 HzTransformer RU-1803440 VAC 1ø, 50-60 HzSensor Adapter*4 or Switching HUBHUB-100ANTENNA UNIT(w/Performance Monitor PM-52A)SN36CF-RSB-129TRANSCEIVER UNITRTR-107Sub displayAntenna CableLAN SerialSelect oneSelect oneSelect onePSU-014 or PSU-015POWER SUPPLY UNIT100-115/220-230 VAC 1ø, 50-60 Hz(for de-icer)Radar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026Monitor Unit MU-190*3 MU-231*3Digital In (ACK IN)VDRIntelligent HubHUB-3000*: See the notes on page xxvi.

SYSTEM CONFIGURATIONSxxivFAR-3330SW/FAR-3230SW-BB100-115/220-230 VAC1ø, 50-60 HzSerial 1, 2IEC 61162-2(Gyrocompass*1, AIS)Serial 3 - 7 IEC 61162-1(EPFS*2 (Navigator), SDME (Speed Log), Echo Sounder, Wind, Alarm*5 Navtex, etc.)Digital Out 1 - 6*51: System Fail2: Power Fail3: Normal Close 14: Normal Close 25: Normal Open 16: Normal Open 2100-230 VAC 1ø, 50-60 HzTransformer RU-1803440 VAC 1ø, 50-60 HzSensor Adapter*4 or Switching HUBHUB-100ANTENNA UNIT (w/Performance Monitor PM-52A)SN36CF-RSB-131Sub displayEC-3000PROCESSOR UNITLAN SerialPSU-014 or PSU-015POWER SUPPLY UNITSelect oneSelect oneSelect oneTRANSCEIVER UNITRTR-109100-115/220-230 VAC 1ø, 50-60 Hz(for de-icer)Coaxial cableAntenna CableRadar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026Monitor Unit MU-231*3Digital In (ACK IN)VDRIntelligent HubHUB-3000*: See the notes on page xxvi.

SYSTEM CONFIGURATIONSxxvFAR-3230S-SSD/FAR-3330S-SSD/FAR-3230S-SSD-BB100-115/220-230 VAC1ø, 50-60 HzPSU-016 or PSU-018POWER SUPPLY UNITEC-3000PROCESSOR UNITSerial 1, 2IEC 61162-2(Gyrocompass*1, AIS)3Serial 3 - 7 IEC 61162-1(EPFS*2 (Navigator), SDME (Speed Log), Echo Sounder, Wind, Alarm*5, Navtex, etc.)Digital Out 1 - 6*5 1: System Fail2: Power Fail3: Normal Close 14: Normal Close 25: Normal Open 16: Normal Open 2100-230 VAC 1ø, 50-60 HzTransformer RU-1803440 VAC 1ø, 50-60 HzSensor Adapter*4 or Switching HUBHUB-100ANTENNA UNIT(w/Performance Monitor PM-52B)SN36CF-RSB-133TRANSCEIVER UNITRTR-111Sub display Antenna CableLAN SerialSelect oneSelect oneSelect one100-115/220-230 VAC 1ø, 50-60 Hz(for de-icer)Radar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026ECDIS Control Unit RCU-024Radar Control Unit RCU-025Trackball Control Unit RCU-026Monitor Unit MU-190*3 MU-231*3Digital In (ACK IN)VDRIntelligent HubHUB-3000*: See the notes on page xxvi.

SYSTEM CONFIGURATIONSxxviCategory of unitsAntenna units: Exposed to the weatherOther units: Protected from the weatherNotes1. The gyrocompass must be type approved for compliance with IMO resolution A.424(XI) (and/or resolution A.821(19) for installation on HSC). The gyrocompass must also have an update rate that is adequate for the ship’s rate of turn. The update rate must be better than 40 Hz (HSC) or 20 Hz (conventional vessel).2. The EPFS must be type approved for compliance with IMO resolution MSC.96(72).3. These monitors have been approved by the IMO, MU-190 for CAT 2C and CAT 2HC, MU-231 for CAT 1C and CAT 1HC. If a different monitor is to be used on IMO vessels, its effective diameter must meet the applicable Category requirements:• CAT 1C and CAT 1HC: effective diameter 320 mm or higher• CAT 2C and CAT 2HC: effective diameter 250 mm or higherFor installation, operation and viewing distance of other monitor, see its manuals.For BB type, a monitor unit is prepared by user.4. The sensor adapters are Control Serial MC-3000S, Analog IN MC-3010A, Digital INMC-3020D and Digital OUT MC-3030D.5. Characteristics of contact output for Alarm:• (Load current) 250 mA• (Polarity) Normally Open: 2 ports, Normally Close: 2 ports• Serial I/O for alarm is also possible, which complies with IEC 61162-1.6. Junction boxes are required for antenna cable length greater than 100 m. Max. cable length is 400 m.

1-11. OPERATIONAL OVERVIEW1.1 Units of the System1.1.1 Radar Control Unit RCU-025The Radar Control Unit RCU-025 consists of various controls and a trackball module (trackball, scrollwheel and left and right buttons). The trackball module functions like a PC mouse. The user rolls the trackball and operates the left and right buttons and the scrollwheel to do various functions.When you press the correct key, a single beep sounds to alert you to correct opera-tion. For wrong operation, several beeps sound. You can select the loudness of the beep or deactivate the beep on the [Customize] menu.No. Control Description1 Turns the system on or off. (With a FURUNO monitor unit, the monitor is also turned on or off with this switch.)2 Status LED The color and state of the LED change according to system or alert status.Green, lighting: Normal operation status; no alerts generated.Green, flashing: The heater on the CPU board is on, because ambient temperature is not at least 0°C. The heater takes about two minutes to warm the equipment. The LED lights green after the heater goes off.Red, lighting: Acknowledged alert or SYSTEM FAIL. SYSTEM FAIL oc-curs when there is trouble in the Processor Unit or communication failure between the Processor Unit and a Control Unit. Each Control Unit detects trouble and its lamp flashes in red and the buzzer sounds. If this condition occurs at the No. 1 Control Unit, the SYSTEM FAIL signal is output.Red, flashing: Unacknowledged alert or SYSTEM FAIL.34Rotary control,EBL1, EBL2Rotary control: Adjusts the active EBL.EBL1, EBL2: Activates or deactivates the respective EBL.4488991010111112121313141416161717181820202121222223232424252526262727292930303737112228283336363232151555333334343535191931317766Navigation toolDisplay controlRadar signal processingRadar systemNavigation toolTargetRangeAlert Menu control

1. OPERATIONAL OVERVIEW1-25 ALARM ACK • Acknowledges unacknowledged alert.• Silences the audio alarm.6 InstantAccess knobSelects the buttons on the InstantAccess bar.7 ESC Goes back one step in current operating sequence on the InstantAccess bar.8BRILL Rotate: Adjusts the brilliance of the display (FURUNO-supplied monitor only). Push: Selects a color palette.9 A/C RAIN Rotate: Suppresses rain clutter.Push: Toggles between manual and automatic rain clutter adjustment.10 A/C SEA Rotate: Suppresses sea clutter.Push: Toggles between manual and automatic sea clutter adjustment.11 GAIN Adjusts the sensitivity of the radar receiver.12 HL OFF • Temporarily erases everything except radar echoes when pressed and held down.• Enters the numeric 1.• Selects like-numbered menu item.13 EBL OFFSET • Activates or deactivates the offset EBL.• Enters the numeric 2.• Selects like-numbered menu item.14 MODE • Selects a presentation mode.• Enters the numeric 3.• Selects like-numbered menu item.15 STBY/TX Toggles the radar between standby and TX.16 OFF CENTER • Puts sweep origin at the cursor location.• Enters the numeric 4.• Selects like-numbered menu item.17 CU/TM RESET • Course-up: Resets heading line to 000°.• True motion: Moves own ship position 75% of the radius in stern direc-tion.• Enters the numeric 5.• Selects like-numbered menu item.18 INDEX LINE • Selects an index line (in the PI line box).• Long-press to activate or deactivate selected index line.• Enters the numeric 6.• Selects like-numbered menu item.19 MENU Opens, closes the menu.20 VECTOR TIME • Sets the vector time (length) for TT and AIS targets.• Enters the numeric 7.• Selects like-numbered menu item.21 VECTOR MODE• Sets the vector mode (relative, true) for TT and AIS targets.• Enters the numeric 8.• Selects like-numbered menu item.22 TARGET LIST • Displays AIS, TT data in the target list.• Enters the numeric 9.• Selects like-numbered menu item.23 CANCEL Cancels the changes made on the currently selected menu.24 TRAIL • Goes back one page in the menu.• Moves cursor leftward in text box.• Turns the echo trail display on or off.• Long-press to reset all trails.No. Control Description

1. OPERATIONAL OVERVIEW1-325 PANEL • Adjusts the backlighting of the keys.• Enters the numeric 0.• Selects like-numbered menu item.26 MARK • Goes forward one page in the menu.• Moves cursor rightward in text box.• Inputs selected mark on the radar screen, at the position selected.27 ENTER Confirms selection on menu.2829Rotary control,VRM1, VRM2Rotary control: Adjusts the diameter of the active VRM.VRM1, VRM2: Activates or deactivates the respective VRM.30 UNDO Undoes edit or text input when creating a radar map, route, user chart.31 VIEW/HIDE Radar mode, chart radar mode: Shows or hides the AZ box, Drop mark boxes, Mark box, PI line box, Trial box.Chart mode: Shows or hides the EBLs, InstantAccess bar, [Overlay/NAV Tools] box, [Route information] box, VRMs.32 RANGE Selects radar range (radar and chart radar modes), chart scale (chart mode).33 ACQ/ACT • TT: Acquires cursor-selected target, for target tracking.• AIS: Activates cursor-selected sleeping AIS target.34 TARGET DATA Displays the detailed data for selected TT, AIS target, in the TT/AIS infor-mation box.35 TARGETCANCEL• TT: Stops tracking cursor-selected tracked target.• AIS: Sleeps cursor-selected activated AIS target.• Long-press to erase all displayed TT target data.36 TrackballmoduleThe trackball module is the same as that used in the Trackball Control Unit RCU-026. See the description in the next section.37 USB port For connection of USB flash memory (FAT16 or FAT32 format). Do not con-nect a USB HDD or PC keyboard. The DVD drive (Maker: TEAC, Type: PU-DRV10) is for chart updates. No. Control Description

1. OPERATIONAL OVERVIEW1-41.1.2 Trackball Control Unit RCU-026The Trackball Control Unit RCU-026 has a power switch, a trackball module (trackball, scrollwheel and left and right mouse buttons), a status LED, and a USB port. The trackball module functions like a PC mouse; the user rolls the trackball and operates the left and right buttons and the scrollwheel to do various functions.No. Control Description1 Power switch Turns the system on or off. (With a FURUNO monitor unit, the monitor is also turned on or off with this switch.)2 Status LED The color and state of the LED change according to system or alert status. See the Status LED description on page 1-1.3 Left button • Does the operation related to the object selected.• Confirms the operation done for the object selected.4 Scrollwheel • Selects menu options.• Selects chart scale.• Sets numeric data.(The scrollwheel does not have a "push" function.)5 Right button • Displays context-sensitive menu when the cursor is put in the displayarea.• Cancels operation done on the object selected.6 Trackball • Moves the cursor.• Selects an object.7 USB port For connection of USB flash memory (FAT16 or FAT32 format). Do not con-nect a USB HDD or PC keyboard.11336677445522

1. OPERATIONAL OVERVIEW1-51.1.3 Processor Unit EC-3000The Processor Unit is the heart of the chart system, and is mainly responsible for the chart management, route planning and route navigation.The Processor Unit has two power switches. The Mains switch controls the power from the switchboard, and the Power switch controls the power to the chart radar sys-tem.Note 1: Do not operate the chart radar with a DVD or CD inserted in the DVD drive, to prevent damage to the drive and media. Remove media from the drive after usage. Insert media only to update charts. After completion of an update, remove the media from its drive and store it in its case. Store media out of direct sunlight, in a place where temperature and humidity are moderate and stable.Note 2: To keep the system stable, restart the unit at least once every two weeks.Note 3: Close the lid of the DVD drive when the drive is not in use.1.2 How to Turn the System On/OffNormally, leave the power switches at the front of the Processor Unit on and control the power with the power switch on a Control Unit (RCU-025, RCU-026). The monitor unit is powered independently.How to power the systemPush the mains switch on the Processor Unit for the "I" position. Turn on the power switch on the Processor Unit or a Control Unit. The start-up display appears on the monitor.After the power is applied, the program starts up and about one minute later the bear-ing scale appears. The radar then goes into three minutes of warm-up time to warm the magnetron, which transmits radar pulses. The timer at the center of the screen counts the time remaining for warm-up. When the timer shows 0:00, the indication "ST-BY" appears at the screen center. The radar is now ready to transmit radar puls-es. In the stand-by condition, no radar pulses are transmitted and TT nor AIS is active.The settings on the menus are stored in a non-volatile memory (hard disk) and are preserved when the power is turned off.Note 1: The solid state radar does not have a magnetron, therefore it has no warming period.Power switchDVD driveMains switch

1. OPERATIONAL OVERVIEW1-6Note 2: If the ambient temperature is less than 0°C (32°F) when the power is applied, nothing appears on the display and the Status LED on the Control Unit flashes. This is because the heater is warming the unit. The display appears in approx. two minutes. How to power off the systemPress the power switch on the Processor Unit or a Control Unit. Push the Mains switch for the "O" position. Note: Provided that the radar was once in use with the transmitter tube (magnetron) still warm, you can put the radar in transmit state without three minutes of warm-up. If the Power switch was turned off by mistake or the like and you wish to restart the radar promptly, turn on the Power switch not later than 10 seconds after power-off.1.3 How to Select a Color PaletteThis radar provides three sets of color and brilliance sets (palette), day, dusk and night, to match any ambient lighting condition. The default specifications of each pal-ette are as shown in the table below. The panel dimmer setting is automatically changed, and the number of steps depends on the color palette selected.To select a palette, do the following:1. Click the [Palette] button.Palette Brilliance Panel dimmer (step)TextcolorBackgroundcolorMU-190 MU-231Day-gray 86 88 15 White GrayDay-blue 86 88 15 White BlueDusk-gray 77 79 7 Light gray Dark grayDusk-blue 77 79 7 Light gray Dark blueNight-gray 53 53 3 Orange Dark grayNight-blue 53 53 3 Light gray Dark blue [Palette] button

1. OPERATIONAL OVERVIEW1-72. Click [Day], [Dusk] or [Night] as appropriate. For example, select [Day] to show its options.3. Click the palette (gray, blue) desired.Note: A palette can also be selected by pushing the BRILL control on the Control Unit.1.4 How to Adjust the Display Brilliance (FURUNO monitor)The brilliance setting is defined according to the color palette setting (see section 1.3). However, manual adjustment of the brilliance is also possible.Note 1: The brilliance of the FURUNO monitor can only be adjusted from the Control Unit. Use a serial cable for brilliance adjustment to make the connection between the Processor Unit and the Control Unit.Note 2: Improper brilliance may affect the visibility of information, especially on the night display.How to adjust the brilliance manually with the BRILL controlOperate the BRILL control to adjust brilliance. Turn it clockwise to increase the bril-liance; counterclockwise to decrease the brilliance. Watch the brilliance level indica-tion on the [BRILL] button (see the illustration below) to see the current brilliance level.How to adjust the brilliance manually with the InstantAccess knob1. Push the InstantAccess knob.2. Rotate the knob to select the [BRILL] button then push the knob to show the bril-liance adjustment window.3. Push the knob, rotate the knob to set the brilliance then push the knob to confirm the setting. The calibration state indication changes to "UNCALIB". 4. To restore the default setting, rotate the knob to select the [CALIB] button then push the knob. The calibration state indication changes to "CALIB".86Current brilliance level[CALIB] button[BRILL] buttonCalibration stateCALIB: Default settingUNCALIB: Manual setting

1. OPERATIONAL OVERVIEW1-8How to adjust the brilliance manually using the trackball module1. Click the [BRILL] button on the InstantAccess bar to show the brilliance adjust-ment window. 2. For coarse adjustment, put the cursor on a location within the slider bar area then push the left button. For fine adjustment, put the cursor on the end of the slider bar and roll the trackball while holding down the left button. 3. Release the left button to confirm setting. The calibration state indication changes to "UNCALIB".4. To restore the default setting, click the [CALIB] button. The calibration state indi-cation changes to "CALIB".1.5 Operating ModesThis chart radar has the following operating modes:1.5.1 How to select an operating modeClick the [Operating Mode] button to select desired mode from the pull-down list. Se-lect [RADAR] for the radar or chart radar mode or [CHART for RADAR] for the chart mode.1.5.2 Limitations when using the chart radar modeThe presentation mode for the chart radar mode can be course-up RM, north-up RM, or north-up TM. The presentation mode is automatically switched to north-up RM if the mode is head-up at the time the chart radar mode is selected.• [RADAR]: - The radar mode provides the traditional radar display.- The chart radar mode overlays the electronic chart on the radar image.• [CHART for RADAR]: The chart mode shows the electronic charts.[Operating Mode] buttonRADARRADARCHARTfor RADAR

1. OPERATIONAL OVERVIEW1-91.6 Display ScreensAll display screens have operational buttons, boxes and indications, and display mark-ers. Click a button or indication to execute the related operation. Context-sensitive menus are available with several boxes and objects. Right-click the appropriate box or object to show the related context-sensitive menu.Monitor viewing distanceThe optimal viewing distance for the FURUNO-supplied monitors is 1020 mm.1.6.1 Radar displayThe illustration below shows the markers, data, etc. as they appear on the FURUNO 19-inch monitor unit. The layout for the 23-inch monitor unit is partially different - the button appears on the bottom of the InstantAccess bar.No. Name Description1 Status bar • Selects an antenna.• Selects the operating mode.• Adjusts the radar picture.• Displays radar operational messages. See section 1.7.Depth : 22.5 mWaterTEMP : 10.5°C REL : 006.3°R Wind : 12.1 m/s Current : 121.3°R 1.7 kn NAV data Route 1 Route 2NESW01020304050-30 -20 -10 min mIndicationarea**: For solid state radar,TX CH1TX CH2OFF181814141313889955667711223344151516171734333232 313526261919202121 2223232525242928 2730301010111212ACE6

1. OPERATIONAL OVERVIEW1-102 Sensor information, datum boxShows your ship's heading, heading source, ship's speed, water tracking speed, speed source, course over ground, speed over ground, course and speed source, ship's position, position source, chart datum.Note: Position source shall meet the requirements of IMO MSC.112(73).3 Menu Drop-down menu with various radar and chart functions.4 Information box Provides various navigation data and route information.5 TT/AIS setting box Sets the parameters for TT and AIS targets.6 Trail box Sets the parameters for the target trails.7 Alert box Shows alert messages by alert name and alert number.• Unacknowledged or regenerated alerts flash in red (alarm) or yel-low-orange (warning).• Acknowledged alerts are shown in normal video.8 Acquisition zone box Sets an acquisition zone for TT, AIS.9 VRM boxes Shows the range and TTG to the VRM1, VRM2.10 Target list button Displays the TT and AIS target list.11 Trial maneuver box Sets the parameters for the trial maneuver.12 Drop mark 2 box Shows the bearing and range to the drop mark 2.13 EBL boxes Shows the bearing to the EBL1, EBL2.14 Mark box Selects the mark to inscribe on the radar display.15 Drop mark1 box Shows the bearing and range to the drop mark 1.16 PI line box • Adjusts the direction and width of the parallel index lines.• Activates or deactivates the parallel index lines.17 Watch box Counts down the time remaining until the buzzer sounds to alert the operator to view the radar picture.18 InstantAccess bar Quick access to often-used radar, chart radar and chart functions. For radar and chart radar functions, see section 1.8. For chart functions, see paragraph 6.1.3.19 Tuning bar Shows tuning status. (No function with solid state radar.)20 Range/Presentation mode box• Selects the radar range.• Selects the presentation mode.21 REF point box Selects the reference point (antenna or CCRP) for measurements (range, bearing, etc.) and markers (position, etc.)22 Heading line Indicates ship's heading.23 Bearing scale The bearing scale provides an estimate of the bearing to a target.24 Cursor position box This box shows• Latitude and longitude of the cursor position.• Range and bearing to the cursor position.• TTG to the cursor position.25 EBL1 Measures the bearing to a target.26 EBL227 VRM1 Measures the range to a target.28 VRM229 Drop mark 1 Finds the range and bearing to drop mark position.30 Drop mark 231 Antenna marker A cross marks antenna position.32 Own ship marker An inverted “T” marks your ship’s position.33 Stern marker Marks location of stern.34 North marker Marks North.35 Range rings Provide an estimate of the range to a target.No. Name Description

1. OPERATIONAL OVERVIEW1-11How to minimize, maximize the boxes at the bottom of the screenThe boxes at the bottom of the screen that contain an arrow can be minimized. Click the arrow to minimize the box. To restore maximum size, click the minimized box.Example: Mark boxNote: The respective VRM or EBL is erased from the screen when the corresponding VRM or EBL box is minimized.1.6.2 Chart radar displayThe chart radar display overlays an electronic chart on the radar picture. To switch be-tween the radar and chart radar displays, click the [Chart ON/OFF] button on the In-stantAccess bar.Click arrow to minimize.Click here to maximize.Click to hide, show chart.OFFACE

1. OPERATIONAL OVERVIEW1-121.6.3 Chart displayThe chart display shows only the electronic chart. Click the [Operating Mode] button to select [CHART for RADAR] to activate this display. See chapter 6 for a description of the chart display.Select [CHART for RADAR]. CHARTfor RADAR0.5NM 4minAUTO ACT FILT

1. OPERATIONAL OVERVIEW1-131.7 Status BarThe Status bar is displayed at the top of screen in all modes. This bar provides, in the radar and chart radar modes, buttons for selection of the mode, antenna and chart da-tabase, and adjustment of the radar picture.For a description of the Status bar used in the chart mode, see paragraph 6.1.2.1.7.1 Status bar for radar, chart radar mode*: The indication is grayed out when the Automatic Clutter Elimination (ACE) function is [ON].No. Button name Description1 Operating Mode Selects a mode: RADAR or CHART for RADAR.2 STBY TX Toggles the radar between stand-by and transmit.3 Antenna Selects an antenna.4Customize EchoPresets the radar controls for specific navigation purpose; for example, congested waters.5 Chart database Selects the IMO chart database (base, primary, standard or all). Available in the chart radar mode.6 RAIN* Reduces rain clutter.7 SEA* Reduces sea clutter.8 GAIN Adjusts the gain of the radar receiver.9 Settings Manages user profiles; opens the Settings menu.10 Date • Displays the date.• Selects the time to use, local or UTC.• Sets the time difference between local and UTC (to use local time).11 Time Displays the time, local or UTC.12 Working IndicatorRotates clockwise if the system is working properly.Picture freezeIf the picture freezes, the picture is not updated. After the picture freezes, the buzzer sounds and the Status LED blinks in red. Reset the power to re-store normal operation. 112111023467895

1. OPERATIONAL OVERVIEW1-141.7.2 How to operate the buttons, slider bars on the Status barThe Status bar has three types of controls: toggle button, drop-down list button and slider bar. You operate the buttons and bars with the trackball module.Control type Example of controlToggle buttonA toggle button alternately selects one of two functions assigned to a button. For example, the [STBY TX] button toggles the radar between stand-by and TX. The background color of the [STBY TX] button momentarily changes to light- blue when switching from stand-by to TX.Drop-down list buttonA drop-down list button provides a list from which to select an option related to the label on the but-ton. A drop-down list button is identified by a tri-angle on the button’s bottom-right corner. The [Chart database] button, shown in the right figure, is an example of a drop-down list button.Slider barThe slider bars provide for adjustment of the ra-dar picture. [RAIN], [SEA] and [GAIN] are slider bar buttons. To adjust the bar coarsely, put the cursor at any location within the slider bar area then push the left button. For fine adjustment, put the cursor at the end of the slider bar and roll the trackball while holding down the left button. Re-lease the button to finish.STBY TXClick button to show drop-down list.

1. OPERATIONAL OVERVIEW1-151.8 InstantAccess BarThe InstantAccess bar runs vertically along the left edge of the screen and is displayed always. This bar provides, in the radar and chart radar modes, buttons for adjustment of the radar picture and chart, AIS operations, display brilliance con-trol (FURUNO monitor only), MOB, screenshot, etc.For a description of the InstantAccess bar used in the chart mode, see paragraph 6.1.3.*1: For solid state radar, [TX CH] icon is displayed instead of [TUNE].*2: This button is not displayed on the FURUNO 19-inch monitor unit.Radar mode, map ONRadar mode, chart ON112111023467895131415161718*2*1IROFFESOFFEAVOFFHLOFFCU/TMresetPULSEM3TUNEMANMAPOFFChartONChartDispOWNAISAISDay88MOBIROFFESOFFEAVOFFHLOFFCU/TMresetPULSEM3TUNEMANMAPONChartOFFChartDispOWNAISAISDay88MOBACEOFFACEOFF

1. OPERATIONAL OVERVIEW1-16No. Button name Description1 PULSE Selects the radar pulse length.2 TUNE Selects the radar receiver tuning method, automatic or manual, and manually tunes the radar receiver.TX CH Selects the transmit frequency from [TX CH 1] or [TX CH 2].3 IR Activates or deactivates the interference rejector.4 ES Activates or deactivates the echo stretch.5 EAV Activates or deactivates the echo averaging when Automatic Clut-ter Elimination (ACE) function is off.6 ACE Activates or deactivates the Automatic Clutter Elimination (ACE) function.Automatic Clutter Elimination (ACE) automatically sets the gain, rain and sea clutter controls according to the sea and rain clutter states.7 HL OFF Temporarily erases everything but radar echoes.8 CU/TM reset • Puts the ship’s heading at the top of the screen in course-up mode the moment this button is pressed.• Resets the ship's position to a point of 75% radius opposite to the extension of the heading line passing through the display center in true motion modes.9 MAP ON/OFF Shows or hides the radar map marks on the radar display, in the radar mode.10 CHART ON/OFF Shows or hides the electronic chart.11 Chart Disp Shows or hides various chart objects. Shown in the chart radar mode. See paragraph 2.41.2.12 OWN AIS Shows the [VOYAGE DATA] menu, to set your ship’s AIS data.13 AIS message Displays screen for “received AIS messages”.14 Palette Selects a color palette.15 BRILL Adjusts the brilliance of a FURUNO monitor.16 MOB Enters a MOB mark at the current position.17 Capture Takes a screenshot.18 UNDO Restores previous condition in radar map and text input.

1. OPERATIONAL OVERVIEW1-171.8.1 How to operate the buttons, slider bars on the InstantAccess barThe InstantAccess bar has three types of controls: toggle button, drop-down list button and slider bar. (The MOB and Capture buttons are special buttons.) You operate the buttons and bars with the trackball module or the InstantAccess knob. This section shows you how to use the InstantAccess knob.1. Push the InstantAccess knob to enable its use with the InstantAccess bar.2. Rotate the InstantAccess knob to select a button. The background color of the button selected is light-blue.3. Do one of the following depending on button type.1) Toggle button: Push the knob to select setting.2) Drop-down list button or slider bar: Push the knob then rotate the knob to select an item or adjust the slider bar. Push the knob to confirm your selection.Note: You can use the ESC key to go back one step in the current operating sequence.Toggle button Drop-down list button Slider barA drop-down list button provides a list from which to select an option related to the label on the button. A drop-down list button is identified by a tri-angle on the button’s bottom-right corner. [Palette] buttonPalette list

1. OPERATIONAL OVERVIEW1-181.9 Sensor Information, Datum BoxColor of nav data indications and sensor nameThe color of the nav data indications and sensor names changes according to the state of the sensor data. The table shown below provides basic indication and color meanings. For detailed information, see Appendix 3. When no sensor data is received, the sensor source indication is blank and the related indication shows asterisks.Sensor information, datum box displays the sensor data and the name of the datum in use. The sensor indications and names are colored according to sensor state. See the ta-ble below.• HDG: Heading and its source.• SPD: Longitudinal speed and its source. The direction of transverse speed is indi-cated with arrows, , Starboard, , Port.• COG: Course over ground and its source.• SOG: Speed over ground and its source.• POSN: Latitude and longitude position of own ship and its source.• Datum: Chart datum (WGS84, WGS72, etc.) in use. No datum appears when there is no datum sentence.Note: The position source shall meet the requirements of IMO MSC.112(73).Nav data indication Color of nav data indicationColor of sensor name StateGreen White Sensor is normal.Yellow White Validity of data is low or offset is applied.Yellow-orange Yellow-orange Data is invalid.Green, data shown with as-terisks (***.*)No display Data is not being re-ceived.Yellow Yellow Data is input manually (manual heading, gyro correction, manual speed, dead reckoning). 12.5kn0.3knGPS1GPS1286.0°T13.1knGPS1 30°00.0000'N020°00.0000'E

1. OPERATIONAL OVERVIEW1-191.10 Menu OverviewThe menu consists of eight main menus and several sub menus. You can operate the menu with the Radar Control Unit or trackball module. The system closes open menus whenever there is no menu operation for 30 seconds.1.10.1 Basic menu operation1. Open the main menu.Control Unit: Press the MENU key.Trackball module: Click the menu title bar at the right side of the display.2. Select a menu.Control Unit: Press the corresponding numeric key. For example, press the 3 key to show the [NAV TOOL] menu.Trackball module: Click the menu desired. The current selection is highlighted in blue.3. Select a menu item.Control Unit: Press the corresponding numeric key.Trackball module: Click the menu item desired. The current selection is highlight-ed in blue.4. Select a menu option.Control Unit: Press the corresponding numeric key. The current selection is high-lighted in orange.Trackball module: Spin the scrollwheel. The current selection is highlighted in or-ange.5. Confirm your selection.Control Unit: Press the ENTER key. Trackball module: Push the left button.Note: Hereafter, "select" in a menu operating procedure means to press the applica-ble numeric key on the Control Unit or push the left button on the trackball module.Menu title barClick [3 NAV TOOL] or press the 3 key.

1. OPERATIONAL OVERVIEW1-20Keys, buttons to use in menusControl UnitMENU key: Open main menu, or close menu.CANCEL key: Go back one layer in menu, or close menu when main menu is dis-played.←key: Return to main menu, in no. 2 layer or higher.Trackball moduleRight button: Go back one layer, or close menu when main menu is displayed.Left button: (1) Click menu title bar to go back one layer, or close menu when main menu is displayed, (2) Click the left arrow on the menu title bar to return to the main menu, in no.2 layer or higher.1.10.2 Menu history featureThis chart radar remembers the 10 last-used menus to help you go to recently used menus quickly. The memorized menus are cleared when the power is turned off. In-stallation- and service-related menus and menus where no operation occurred are not memorized. Menus accessed multiple times are counted as one menu.Click the memory history buttons on the menu title bar to navigate through the last-used menus.For example, the last two used menus are [NAV TOOL] and [AIS].Menu history buttonsHistory back buttonHistory forward buttonMemorized menu no. 1Memorized menu no. 2ClickClick

1. OPERATIONAL OVERVIEW1-211.10.3 How to enter numeric dataSelect the numeric data, then do one of the following:Control Unit: Use the ten keys to enter data.Trackball module: Spin the scrollwheel to set data then push the left button.1.10.4 How to enter alphanumeric character dataSome operations display a software keyboard to enter alphanumeric character data.To enter characters, click applicable characters on the software keyboard. You can switch between letter input and symbol input by clicking the key circled in the illustra-tion above.Click to switch between letters and symbols.

1. OPERATIONAL OVERVIEW1-221.11 Context-Sensitive Menus in the Radar ModeContext-sensitive menus are available with many of the boxes and buttons surround-ing the display area and objects within the display area. Right-click the boxes and but-tons marked with numerals in the illustration below to show the related context-sensitive menus. If a menu is not operated within 30 seconds, it is automatically closed.For context-sensitive menus in the chart mode, see the chapter on chart overview.1.11.1 Context-sensitive menus available with buttons and boxesNo. Box name Menu No. Box name Menu1 Adjust Local Time Adjust Local Time 2 Cursor Position Range-Bearing Po-sition, X-Y Position, Cursor Menu3 Sensor Informa-tion, Datum BoxSelect Sensor, OS Info Menu4 AIS Info Expanded AIS Data, AIS Message5 Association Association OFF/TT/AIS, Association Menu6 TT OFF / MAN / AUTO / MAN/AUTO,TT Menu, Symbol Menu7 AIS DISP OFF / FILT / ALL, AIS Menu, Symbol Menu8 Vector OS Vector Menu, Target Vector Menu240.8°3229°0.0884232023282931323938363534 578 14 1615213021406101317 18113394201922242526271241Context-sensitive menus on the radar echoes(see paragraph 1.11.2)37

1. OPERATIONAL OVERVIEW1-23*: For solid state radar, this menu is not displayed.9 Vector Time Vector Time (30 s - 60 min), OS Vector Menu, Target Vector Menu10 Vector Reference True-G(S), REL, OS Vector Menu, Target Vector Menu11 CPA Range CPA Range (0.5 - 20 NM)12 CPA time CPA Time(1 - 60 min)13 AIS CPA Auto Activate Menu 14 Auto Activate OFF, AUTO ACT FILT, AUTO ACT ALL, Auto Activate Menu15 Lost TGT TT Lost Filter Menu, AIS Lost Filter Menu16 Lost TGT Filter OFF, FILT, ALL, TT Lost Filter Menu, AIS Lost Filter Menu17 Past POSN Past POSN Menu 18 Past POSN time Past POSN Time (OFF, 30 s - 6 min), Past POSN Menu19 Trail Trail All Clear, Trail Menu20 Trail Time Trail Time (OFF, 15 s - 30 min, CONT), Trail Menu21 Trail/Past POSN ReferenceTrue-G(S), REL, Past POSN Menu, Trail Menu22 Alert List Alert List/Log Win-dow23 Trial Trial Mode, TrialManeuver Menu24 AZ Acquisition Zone Menu25 Drop Mark 2 Drop2 Off 26 VRM 2 VRM2 Off, EBL•VRM Menu27 VRM 1 VRM1 Off,EBL•VRM Menu28 EBL 2 EBL2 Off,EBL•VRM Menu29 EBL 1 EBL1 Off,EBL•VRM Menu30 Drop Mark 1 Drop1 Off31 Mark Mark Color (B-type only), Mark Position, MAP File, Edit Map Comment, Map•Mark Menu32 PI Line Number of PI Line, Reset PI Line,PI Menu33 Watch Watch Time(OFF, 6 - 20 min)34 Brill Menu Brill Menu35 Chart ON/OFF Chart Display Menu 36 MAP ON/OFF Radar Map Menu, Route Menu, Event Menu, User Chart Menu37 ACE Automatic Clutter Elimination (ACE) Menu38* TUNE Tune Initialize39 PULSE Pulse Menu 40 RANGE Range Scales (0.125 - 96.0 NM)41 Antenna Selection Dual Radar,ANT Select Menu42 Customize Echo Customize Echo MenuNo. Box name Menu No. Box name Menu

1. OPERATIONAL OVERVIEW1-241.11.2 Context-sensitive menus in the display area in the radar and chart radar modesRight-click anywhere in the display area in the radar and chart radar modes to show the context-sensitive menu.[Target Data/ACQ/ACT]: For cursor-selected TT or AIS target, display target data, acquire target for TT, or activate sleeping AIS target.[Target Cancel]: Cancel tracking on selected tracked target (erase target), sleep activated AIS target.[Off Center]: Off center the display.[EBL Offset]: Offset EBL1, EBL2 (to measure range and bearing between two targets).[Zoom Set]: Select zoom area.[Area Select]: Specify the area where to delete, copy marks.[Mark Delete]: Delete cursor-selected mark. Grayed out when radar map is off.[Mark Copy]: Copy cursor-selected mark. Grayed out when radar map is off.[Own Ship Offset]: Apply an offset to own shipposition.[REF Mark]: Make cursor-selected target a reference target (for use in TT). Grayed out unless TT is active.[Cursor Size]: Select cursor size, large or small.[Notes Detail]: Show details about cursor-selected Notes.[MOB Delete]: Delete selected MOB mark.Area selectedThis context-sensitive menu is available when an area is created to cancel tracking on specific targets, or delete or copy marks.[Area Target Cancel]: Cancel tracking on targets within the area selected.[Area Mark Delete]: Delete all marks within the area selected.[Area Mark Copy]: Copy all marks within the area se-lected.[Area Cancel]: Cancel the area created.Radar mode, map ONRadar mode, map OFF or chart ONRadar mode, map ON, area selected

1. OPERATIONAL OVERVIEW1-251.12 Cursor PositionCursor data appears in the cursor position box at the top-right position on the display. The appearance of the box is slightly different between the 23-inch and 19-inch dis-plays, although the content is the same.For the cursor position box that appears in the chart mode, see section 6.6.The indication below the cursor position can show the range and bearing to the cursor or x-y coordinates of the cursor position. Click that indication and select [Range-Bear-ing Position] or [X-Y Position] as appropriate. For the x-y coordinate display, the y-axis is the heading line, right/top is "plus" and left/lower is "minus".Note 1: The cursor bearing can be selected to true or relative with [1 CURSOR BEAR-ING] in the [CURSOR] menu. Right-click the indication and select [Cursor Menu] to open the [CURSOR] menu.Note 2: The cursor position is shown as "---.-" when the cursor is not within the effec-tive display area.1.13 How to Select Sensor SettingsThis radar system accepts navigation data input two ways: System or Local. System shares sensor data among multiple radars in a network. Sensor priority is also com-monly shared among the radars. Local selects a sensor outside the network.1. Right-click anywhere in the Sensor information, datum box to show the context-sensitive menu.2. Click [Select Sensor].3. Click [System] or [Local].Note: The sensor system can also be selected in the chart mode through this pro-cedure and through the menu. Open the menu then select [7 OWN SHIP INFO] followed by [1 SENSOR].Cursor position (lat/lon)Bearing and range to cursor positionTime to go to cursor positionx and y coordinates of cursor positionClick indication to switch between bearing and range and x and y coordinates.SystemLocal[Setting]SystemLocalSelect Sensor[OS Info Menu][Setting]

1. OPERATIONAL OVERVIEW1-261.14 How to Enter Ship SpeedThe TT and azimuth stabilized presentation modes require own ship speed input and compass signal. The speed can be entered automatically from a speed log (STW, SOG) or GPS (SOG), or manually on the menu. Note that the FURUNO GPS Naviga-tor GP-150 provides COG and SOG.1. Right-click anywhere in the Sensor information, datum box to show the context-sensitive menu.2. Click [Select Sensor] then click [Setting].3. Use the arrow buttons to select the [SPD] page.4. For automatic input, follow the procedure below. For manual input, go to step 5.1) Check [Sensors].2) Set the priority for the speed sensors in case of Local sensor. Click the triangle on any line then select the sensor to set as the primary source of speed. All other sensors are then set as secondary source. Only one sensor can be pri-mary while the others can be secondary. If a speed sensor is changed from secondary to primary state and another speed sensor was selected as prima-SystemLocal[Setting]SystemLocalSelect Sensor[OS Info Menu][Setting]Sensor type selectionSpeed sensor listCheck for manual speed inputCheck for automatic speed inputStablilization modeSelect to use radar as source for speed and courseSet speed and course of driftArrow buttons

1. OPERATIONAL OVERVIEW1-27ry, then that sensor previously selected to primary state is then automatically selected to secondary state.3) Select [Bottom] or [Water] at [Stabilization Mode] to set the stabilization meth-od. Select [Bottom] for GPS or [Water] for a speed log.4) Check [GPS] or [LOG] at [Sensor Type] to select the source of speed data.5) Go to step 6.5. For manual input, set the stabilization mode for [Water] and check [Manual]. Click the manual box to show the up and down arrows. Click the arrows to set speed.Note: For [Set Drift], see page 16-3.6. Click the [OK] button to save the settings then click the [MENU] bar to close the menu.Notes on speed input• IMO Resolution A.823(19) for TT requires that a speed log to be interfaced with a TT should be capable of providing through-the-water speed (forward speed).• A single-axis water log cannot measure speed when the wind is coming from the leeway direction.• When AIS is active, [Manual], [Reference SPD] and [Set Drift] are shown in gray to indicate that they are not available for selection.

1. OPERATIONAL OVERVIEW1-281.15 How to Enter HeadingSelect manual or automatic heading input as follows:1. Right-click anywhere in the Sensor information, datum box to show the context-sensitive menu.2. Click [Select Sensor] then click [Setting].3. Use the arrow buttons to select the [HDG] page.4. For automatic input, follow the procedure below. For manual input, go to step 5.1) Check [Sensors].2) Set the priority for the heading sensors. Click the triangle on any line then se-lect the sensor to set as the primary source of heading. All other sensors are then set as secondary source. Only one sensor can be primary while the oth-ers can be secondary. If a heading sensor is changed from secondary to pri-mary state and another heading sensor was selected as primary, then that sensor previously selected to primary state is then automatically selected to secondary state. 3) Go to step 6.5. For manual input, check the [Manual] box. Click the heading input box to show the up and down arrows. Click the arrows to set heading.6. Click the [OK] button to save the settings then click the [MENU] bar to close the menu.Heading sensor listAnalog gyro headingCheck for automatic heading inputGY001GY002Manual heading input (not shown on IMO type) Gyro Correction[Gyro Correction] is not shown● when [SYSTEM] is selected in the [OWN SHIP INFO] - [SENSOR] menu.[Gyro Correction] is grayed out● when manual heading is in use.Arrow buttons

1. OPERATIONAL OVERVIEW1-291.16 How to Mark MOB PositionUse the MOB (man overboard) feature to mark the position of man overboard on the display screen. Click the [MOB] button (in any mode) on the InstantAccess bar.The MOB mark instantly appears at the geographical position of your ship when the button is clicked.Up to 100 MOB marks can be saved. When the capacity for MOB marks is reached, the oldest mark is automatically erased to make room for the latest.To delete an MOB mark, right-click the mark to show the context-sensitive menu then select [MOB Delete]. Exercise caution when using this feature in strong tide or current. The person will not be at the MOB position for a very long time.1.17 How to Offset PositionThe position shown in the Sensor information, datum box (section 1.9) may be differ-ent from the actual position. This error affects the positioning accuracy of radar ech-oes, radar map and TT and AIS symbols. If there is a difference, apply an offset to position as shown below to compensate for the error.1. Right-click the display area to show the context-sensitive menu.2. Select [Own Ship Offset] and push the left button. The color of the cursor be-comes blue.3. Roll the trackball until the cursor is at the "correct position".4. Push the left button to confirm.To cancel the offset, show the context-sensitive menu then select [Reset Own Ship Offset]. The indication [Offset] and the offset values are then erased from the display.[MOB] button Offset value (range, bearing)

1. OPERATIONAL OVERVIEW1-301.18 How to Select Time Format, Set Local TimeThe GPS navigator feeds time and date data to the chart radar and they appear on the Status bar. Neither the time nor the date can be adjusted, however you can select be-tween UTC time (default) and local time. You can switch between the local time and the UTC time by left-clicking the Current time format indication.To use the local time, enter the time difference between the local time and the UTC time as shown below.1. Right-click the Current time format indication to show the context-sensitive menu then click [Adjust Local Time] to display the [Local Time Adjust] dialog box.2. Enter the time difference between the local time and the UTC time, in hours and minutes. Use the button on the left to select the time offset direction. Select "+" if the local time is ahead of the UTC time, or "-" if it is behind the UTC time.1.19 How to Take a Screenshot of the DisplayClick the [Capture] button on the InstantAccess bar to take a screenshot and save it to the SSD (Solid State Drive). You can save a maximum of 100 screenshots. When the capacity for screenshots is reached, the oldest screenshot is automatically deleted to make room for the latest. You cannot take a screenshot when a menu or a dialog box is opened.Screenshots can be copied to a USB flash memory. For how to process screenshots, see section 22.10.Current time formatLeft click: Switch between local and UTC timesRight click: Adjust local timeTime+00[Capture] button

Navigation menu