Furuno Ch250 150 225 Operators Manual
2015-08-11
: Furuno Furuno-Ch250-150-225-Operators-Manual-801075 furuno-ch250-150-225-operators-manual-801075 furuno pdf
Open the PDF directly: View PDF .
Page Count: 118
Download | ![]() |
Open PDF In Browser | View PDF |
Back OPERATOR'S MANUAL COLOR LCD SEARCHLIGHT SONAR MODEL CH-250/CH-250S www.furuno.co.jp The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 All rights reserved. Printed in Japan A : MAR . 2000 P : APR . 08, 2011 Pub. No. OME-13160-P (DAMI ) CH-250/250S *00080894815* *00080894815* * 0 0 0 8 0 8 9 4 8 1 5 * IMPORTANT NOTICES General • • • • • • • • The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury. Do not copy any part of this manual without written permission from FURUNO. If this manual is lost or worn, contact your dealer about replacement. The contents of this manual and equipment specifications can change without notice. The example screens (or illustrations) shown in this manual can be different from the screens you see on your display. The screens you see depend on your system configuration and equipment settings. Save this manual for future reference. Any modification of the equipment (including software) by persons not authorized by FURUNO will cancel the warranty. All brand and product names are trademarks, registered trademarks or service marks of their respective holders. How to discard this product Discard this product according to local regulations for the disposal of industrial waste. For disposal in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the correct method of disposal. How to discard a used battery Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and terminals of battery before disposal to prevent fire, heat generation caused by short circuit. In the European Union The crossed-out trash can symbol indicates that all types of batteries must not be discarded in standard trash, or at a trash site. Take the used batteries to a battery collection site according to your national legislation and the Batteries Directive 2006/66/EU. Cd In the USA The Mobius loop symbol (three chasing arrows) indicates that Ni-Cd and lead-acid rechargeable batteries must be recycled. Take the used batteries to a battery collection site according to local laws. Ni-Cd Pb In the other countries There are no international standards for the battery recycle symbol. The number of symbols can increase when the other countries make their own recycling symbols in the future. i SAFETY INSTRUCTIONS WARNING ELECTRICAL SHOCK HAZARD WARNING Keep heater away from equipment. Do not open the equipment. Only qualified personnel should work inside the equipment. A heater can melt the equipment's power cord, which can cause fire or electrical shock. Use the proper fuse. Immediately turn off the power at the switchboard if water leaks into the equipment or something is dropped in the equipment. Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service. Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire. Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service. Make sure no rain or water splash leaks into the equipment. Fire or electrical shock can result if water leaks in the equipment. ii The fuse in the hull and transceiver units protect them from overvoltage, equipment fault and reverse polarity of the ship's mains. If a fuse blows replace it with fuse of the same amperage. Use of a wrong fuse can result in equipment damage. Retract the transducer before turning off the power. Damage to the equipment may result. Wait until the transducer switch [↑] lights steadily and then turn off the power. CAUTION Do not exceed 20 knots when operating the equipment and do not exceed 15 knots when lowering or raising the transducer. The transducer may become damaged. Do not use the equipment for other than its intended purpose. Use of the equipment as a stepping stool, for example, may result in personal injury or damage to the equipment. Warning labels are attached to the display, transceiver and hull units. Do not remove the labels. If a label is missing or illegible, contact a FURUNO agent or dealer. WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside. TRANSCEIVER UNIT Name: Warning Label (1) Type: 86-003-1011-1 Code No.: 100-236-231 DISPLAY UNIT Name: Warning Label (1) Type: 86-003-1001-1 Code No.: 100-236-741 WARNING Moving shaft can pinch and cut. Keep hands clear while operating. Lockout power before servicing. HULL UNIT Name: "Finger Catch" Warning Label Type: 06-021-4015-0 Code No.: 100-281-590 CAUTION WORKING WITH THE SONAR OIL Precautions Keep oil away from eyes. Wear protective gloves when working with the oil. The oil can cause inflammation of the eyes. Do not touch the oil. Wear protective gloves when working with the oil. The oil can cause inflammation of the skin. Do not ingest the oil. Diarrhea and vomiting may result. Keep the oil out of reach of children. Q Q Q Q Emergency procedures If the oil enters eyes, flush with clean water about 15 minutes. Consult a physician. If the oil is ingested, see a physician immediately. Q Q Disposal of oil and its container Dispose of oil and its container in accordance with local regulations. For further details, contact place of purchase. Storage Seal container to keep out foreign material. Store in dark, cool place. TFT LCD The high quality TFT (Thin Film Transistor) LCD displays 99.999% of its picture elements. The remaining 0.01% may drop out or light, however this is an inherent property of the LCD; it is not a sign of malfunction. iii TABLE OF CONTENTS FOREWORD ............................................................................................. vi SYSTEM CONFIGURATION ................................................................... viii 1. OPERATIONAL OVERVIEW ............................................................ 1-1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Control Description.................................................................................................. 1-1 Remote Controller ................................................................................................... 1-2 Turning the Power On/Off........................................................................................ 1-3 Raising, Lowering the Transducer ........................................................................... 1-4 Adjusting Screen Brilliance, Panel Dimmer ............................................................. 1-5 Selecting a Display.................................................................................................. 1-6 Adjusting the Gain................................................................................................... 1-7 Basic Menu Operation............................................................................................. 1-7 2. HORIZONTAL MODE ....................................................................... 2-1 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 Operational Overview.............................................................................................. 2-1 Typical Horizontal Mode Display ............................................................................. 2-2 Selecting the Range................................................................................................ 2-3 Selecting Sector Width ............................................................................................ 2-4 Selecting Train Center............................................................................................. 2-5 Selecting the Tilt Angle ............................................................................................ 2-5 Selecting the Training Speed................................................................................... 2-9 Finding Echo Position with the Cursor..................................................................... 2-9 Event Marker......................................................................................................... 2-10 Depth and Horizontal Range Markers ................................................................... 2-11 Adjusting the Picture ............................................................................................. 2-12 Target Lock ........................................................................................................... 2-17 Horizontal Menu Overview .................................................................................... 2-21 Interpreting the Horizontal Display......................................................................... 2-23 3. VERTICAL FAN MODE .................................................................... 3-1 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 iv Operational Overview.............................................................................................. 3-1 Typical Vertical Fan Mode Display........................................................................... 3-2 Selecting the Range................................................................................................ 3-3 Selecting Train Center............................................................................................. 3-4 Selecting Display Sector ......................................................................................... 3-5 Selecting Sector Center .......................................................................................... 3-6 Selecting the Training Speed................................................................................... 3-7 Finding Echo Position with the Cursor..................................................................... 3-7 Event Marker........................................................................................................... 3-8 Depth and Horizontal Range Markers ..................................................................... 3-9 Adjusting the Picture ............................................................................................. 3-10 Vertical Menu Overview......................................................................................... 3-12 Interpreting the Vertical Fan Display...................................................................... 3-13 4. ECHO SOUNDER MODE ................................................................. 4-1 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11 Operational Overview.............................................................................................. 4-1 Typical Echo Sounder Display................................................................................. 4-2 Selecting the Range................................................................................................ 4-3 Train Direction......................................................................................................... 4-4 Selecting Tilt Angle.................................................................................................. 4-4 Selecting Picture Advance Speed............................................................................ 4-4 Measuring Range by Cursor.................................................................................... 4-5 Event Marker........................................................................................................... 4-5 Range Marker ......................................................................................................... 4-7 Adjusting the Picture ............................................................................................... 4-7 Echo Sounder Menu Overview.............................................................................. 4-10 5. MENU OPERATION.......................................................................... 5-1 5.1 5.2 5.3 5.4 COM1 Menu............................................................................................................ 5-1 COM2 Menu............................................................................................................ 5-3 Short-cut Menu, Preset Menu.................................................................................. 5-4 SYS Menu............................................................................................................... 5-9 6. MAINTENANCE, TROUBLESHOOTING.......................................... 6-1 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 Preventive Maintenance.......................................................................................... 6-1 Cleaning the Equipment .......................................................................................... 6-1 Hull Unit Maintenance ............................................................................................. 6-2 Transducer Maintenance......................................................................................... 6-3 Fuse Replacement .................................................................................................. 6-3 Troubleshooting ...................................................................................................... 6-4 Error Messages....................................................................................................... 6-5 Diagnostics ............................................................................................................. 6-6 Test Pattern............................................................................................................. 6-8 MENU TREE.......................................................................................... M-1 SPECIFICATIONS ............................................................................... SP-1 INDEX .................................................................................................. IN-1 v FOREWORD Thank you for purchasing the CH-250/CH-250S Color LCD Searchlight Sonar. We are confident you will discover why FURUNO has become synonymous with quality and reliability. Dedicated in the design and manufacture of marine electronics equipment for half a century, FURUNO Electric Company has gained an unrivaled reputation as a world leader in the industry. This is the result of our technical excellence as well as our worldwide distribution and service network. Please carefully read and follow the safety information and operating and maintenance instructions set forth in this manual before attempting to operate the equipment and conduct any maintenance. Your sonar will perform to the utmost of its ability only if it is operated and maintained in accordance with the correct procedures. Features The CH-250/CH-250S displays underwater objects on a bright 10.4” color LCD display, in 8 or 16 colors according to received echo strengths. Operating frequency is selectable among 60, 88 and 150 kHz for CH-250 and 180 and 240 kHz for CH-250S. Eight operating modes provide information for virtually any fishing application. The main features of the CH-250/CH-250S are • High definition active matrix color LCD. • Target lock on a fish school or stationary position (reef, etc.). • Audible detection of echoes frees the operator from continuous watch of the display. • Compact display and hull units permit installation where space is limited. • Interface IF-8000 permits use of a commercial monitor instead of standard display unit. • Automatic pulselength switching for optimum performance in short and long ranges. • Eight operational modes: Horizontal, Expanded Horizontal, Vertical Fan, Echo Sounder, Horizontal/Vertical Fan, History, Video Plotter and Strata. • Automatic retraction of transducer at operator-selected ship’s speed between 5 and 15 knots. • CUSTOM MODE keys provide one-touch setup of the equipment or short-cut key function. • Tracing of ship’s track with connection of position-fixing equipment (GPS, etc.). • One of the echo strengths may be displayed in white to enhance the specific echo level. • The “Vertical Search” feature provides a cross-sectional view of the vertical plane, which is useful for evaluating fish school concentration. vi Usage Precautions • The Motion Sensor MS-100 compensates for ship’s pitching and rolling. However, it does not compensate for load unbalance. • If the equipment will not be used for a long time shut off the power to it at the mains switchboard to prevent battery discharge. • If the soundome is to be operated while the ship is dry-docked set the transmitter output power to “minimum” on the COM1 menu. Damage to the train-tilt section may result if it is operated with maximum transmitter power. • When the ship is dry-docked check for signs of corrosion on the soundome. Find the reason for the corrosion and attach a zinc plate to the hull unit as an anticorrosion measure if necessary. vii SYSTEM CONFIGURATION INTERFACE UNIT IF-8000 Note 2 MONITOR UNIT MU-100C Navigator Control Unit Display Unit Note 1 VGA Ext. Monitor Remote Controller CH-256 TRANSCEIVER UNIT CH-253 CONTROL UNIT CH-252 MOTION SENSOR 12-32 VDC HULL UNIT SPEAKER DATA/VIDEO OUT 12-32 VDC Speaker Motion Sensor MS-100 HULL UNIT CH-254/254S CH-255/255S 12/24-32 VDC Note 1: MU-100C is the standard supply monitor unit. An external monitor may be connected via the interface unit (option). The drawing above shows the system configuration with the MU-100C. The monitor unit and control unit can be installed separately (optional mounting kit required). Note 2: For blackbox type, MU-100C is not supplied. Connect external monitor and control unit to the interface unit. How to remove the hard cover (blackbox type only) Place your thumbs at the locations shown with circles in the illustration at right, and then lift the cover while pressing it with your thumbs. viii 1. OPERATIONAL OVERVIEW 1.1 Control Description Selects center bearing of training sector. Selects detection range. Switches training sector to 360˚ (horizontal mode), or 180˚ (vertical fan mode). Turns the power on/off. Selects scan speed (sonar)/picture advancement speed (echo sounder). Raises the transducer. = Controls tilt angle. = Selects center direction of Adjusts receiver sensitivity. the vertical scanning sector. Selects width of training sector. Turns target lock on/off. Omnipad = Shifts cursor. = Selects menu items, options. XDR GAIN SECTOR RANGE TRAIN POWER MAIN FULL FAST SUB HALF SCAN DISPLAY MODE Lowers the transducer. TILT BRILL TARGET MENU R/B EVENT CUSTOM MODE Select display mode. Provide short-cut key or one-touch setup. Adjusts display brilliance. Alternately selects main and sub windows in combination displays. Horizontal/Video Plotter Opens/closes menu. Inscribes/erases event marker. Inscribes/erases range and bearing markers. Horizontal/Vertical Fan Horizontal/History Horizontal/Strata DISPLAY MODE Horizontal Expanded Horizontal Echo Sounder Vertical Fan Figure 1-1 Control unit 1-1 1.2 Remote Controller The Remote Controller CH-256 (option) provides armchair control over range, tilt, target lock and range of sounding. Select tilt angle. Select display range. Selects range of sounding for full circle 360˚ (horizontal mode) or half circle 180˚ (vertical fan mode). Enables/disables target lock. Figure 1-2 Remote controller Note: The remote controller can also be used with a commercial monitor. 1-2 1.3 Turning the Power On/Off 1.3.1 Power on This sonar has a demonstration mode which lets the operator become acquainted with the features of the sonar. For further details see page 5-18. Press the [POWER] switch on the control unit till hear “click.” A beep sounds, the lamp above the switch lights and the last-used display appears. Note: Wait at least five seconds before reapplying the power. 1.3.2 Power off 1. Press the [↑] switch on the control panel. The lamp above the switch blinks while the transducer is being raised and lights steadily when it is fully raised. 30 25 Transducer status indicator • Up arrow is filled when transducer has been retracted into the tank. • Down arrow is filled when transducer has been fully lowered. • Appropriate arrow flashes during raising/lowering of transducer. NOTE: When the transducer is being raised automatically (auto raise feature), the arrows are filled and the up arrow flashes. When the transducer has been fully retracted, the up arrow lights and the down arrow becomes hollow. 2. Press the [POWER] switch after the [↑] switch lights steadily. Note 1: The transducer is automatically retracted into the tank if the [POWER] switch is pressed before retracting the transducer. However, for safety purposes, make it a habit to retract the transducer before turning off the power. Note 2: After changing settings, wait at least one minute before turning off the equipment to allow the equipment to memorize settings, and start up with them at the next powering of the equipment. No harm will result to the equipment if this not done. 1-3 1.4 Raising, Lowering the Transducer 1.4.1 Lowering the transducer With the boat at the fishing ground, press the [↓] switch to lower the transducer. The lamp above the switch blinks while the transducer is being lowered and lights when it is completely lowered. The down arrow of the transducer status indicator at the top right corner of the display is filled when the transducer is completely lowered. CAUTION Do not exceed 20 knots when operating the equipment and do not exceed 15 knots when lowering or raising the transducer. The transducer may become damaged. 1.4.2 Raising the transducer Press the [↑] switch to raise the transducer. The lamp above the switch blinks while the transducer is being raised and lights steadily when it is fully raised. The up arrow of the transducer status indicator at the top right corner of the display is filled when the transducer is fully retracted. Note 1: With speed input, the transducer can be raised automatically when the ship’s speed exceeds a preset speed between 5 and 15 knots. If speed data is erroneous the transducer may be raised at a speed different from the preset speed. For further details about the automatic retraction feature, see AUTO RETRACTION on page 5-12. Note 2: An alarm may sound depending on ship’s speed. For details see page 5-13. 1-4 1.5 Adjusting Screen Brilliance, Panel Dimmer Screen brilliance can be adjusted in nine steps and panel dimmer (backlighting) in four. 1. Press the [BRILL] key to open the dialog box for screen brilliance and panel dimmer. Do the next step within four seconds, otherwise the dialog box will be erased. BRILL:3 DIMMER:3 Figure 1-3 Brilliance, panel dimmer dialog box 2. Operate or to adjust screen brilliance (0 is the lowest brilliance; 9 the highest). Note that continuous pressing of the [BRILL] key also changes the brilliance level. 3. Operate or to adjust the panel dimmer (0 is the lowest level; 4 is the highest). 4. Press the [MENU] key to register settings and close the dialog box. Note that the dialog box is automatically erased if there is no control operation within about four seconds. Note 1: The brilliance of a commercial monitor cannot be adjusted with the [BRILL] key. Use the associated control on the monitor. Note 2: For the supplied monitor unit, if you turn off the power with the brilliance set at minimum the screen will show nothing at next power-up. In this case press the [BRILL] key several times. 1-5 1.6 Selecting a Display This sonar has eight display modes and you may select one with one of the DISPLAY MODE keys. Refer to the chapter shown in the illustration for more information about each mode. Key Picture Key Picture NAV DATA HORIZONTAL NAV DATA EXPANDED HORIZONTAL This mode provides 360 degree coverage. Useful for general search. (Chapter 2) Zoomed horizontal picture appears over the entire screen. (Chapter 2) NAV DATA or A-SCOPE DISPLAY NAV DATA Water temp/depth VERTICAL FAN Vertical section of underwater conditions appears on the entire screen. (Chapter 3) NAV DATA HORIZONTAL/HISTORY The horizontal picture appears in the main window; the history picture in the sub window. Useful for showing history of fish movement, distribution. (Chapter 2) NAV DATA HORIZONTAL/VERTICAL FAN The horizontal picture appears in the main window; the vertical fan picture in the sub window. (Chapter 3) ECHO SOUNDER Using a fixed spot beam this display shows fish echoes below or around the vessel. (Chapter 4) NAV DATA HORIZONTAL/VIDEO PLOTTER The horizontal picture appears in the main window and the video plotter picture, which traces ship's track, in the sub window. (Chapter 2) NAV DATA HORIZONTAL/STRATA The horizontal picture appears in the main window; the strata picture in the sub window. The strata picture shows bottom undulatons in different colors. It is useful in bottom trawling to avoid projections. (Chapter 2) Figure 1-4 Display modes 1-6 1.7 Adjusting the Gain The [GAIN] control adjusts the sensitivity of the receiver. Normally, the control is adjusted so that the bottom echo is displayed in reddish-brown mixed with red. Initially set the gain between “4” and “6” and then fine tune depending on fishing ground, etc. Too Low Proper Too High Figure 1-5 How to adjust the gain 1.8 Basic Menu Operation The menu, consisting of six menus, mostly contains items which once preset do not require frequent adjustment. Below is the procedure for basic menu operation. 1. Press the [MENU] key to open the menu. Note: Either PRESET (default setting) or SHORT-CUT appears between ES and SYS at the top of the screen depending on the setting of CUSTOM KEY on the SYSTEM SETTING 1 menu, and they set the function of the custom keys [1], [2], [3]. For further details see pages 5-3 through 5-7.) MENU COM1 COM2 DELETING TRACK WHITE MARKER NO OFF SIG LEVEL COLOR BKGD COLOR BEARING READOUT OFF 16 2 RELATIVE : SELECT : CHANGE HORZ VERT ES PRESET SYS MENU: END Figure 1-6 COM2 menu 1-7 2. The last-used menu is displayed. (In Figure 1-6 the COM2 menu is selected.) To select a to select MENU at the top of the screen and then press or to different menu, press select menu desired. or 3. Press provided. to select menu item desired. At the bottom of the screen menu help is 4. Press ► to open the corresponding dialog box. The example below shows the dialog box for DELETING TRACK in the COM2 menu. DELETING TRACK NO YES Figure 1-7 Dialog box for deleting track 5. Press or or to select option desired. If the option requires selection of numeric data, use to lower or raise the figure, respectively. 6. Press or to return to the menu, or press the [MENU] key to register your selection and close the menu. 1-8 2. HORIZONTAL MODE 2.1 Operational Overview The figure below shows the typical horizontal mode operating sequence. 7. Set center bearing of train sector. 6(a). Set scanning sector. 8. Set tilt angle. 5. Set range. 1. Turn on the power. 11. Adjust menu settings 9. Adjust gain. (ex. TVG) as required. XDR GAIN SECTOR POWER DISPLAY MODE 2. Lower the transducer. RANGE TRAIN TILT MAIN FULL FAST SUB HALF SCAN BRILL TARGET MENU R/B EVENT CUSTOM MODE 4. Select appropriate horizontal mode. 6(b). Select training sector for full circle. 10. Measure range and bearing to target with cursor. 3. Adjust screen brilliance. Figure 2-1 Control panel 2-1 2.2 Typical Horizontal Mode Display * Depth marker When depth data is input from external equipment, the depth marker shifts according to depth data. If the depth data is greater than the horizontal range, the depth marker shifts to lowest position. Tilt angle indicator (Indicates transducer tilt angle.) Horizontal max. range 30 Range and bearing markers Demonstration Sector marker mode Cursor data Bottom echo (DEMO) N Interference Range rejector R T 40 m 40˚ Depth marker* (See note at left.) Transducer status indicator Filled arrow: Respective action completed Blinking arrow: Action in progress 30 25 NE NW Target lock indicator Bearing marker Fish echo ETA marker Own ship marker Tilt angle Tilt angle Train indicator 16 13 B208˚ + 25 Vertical max. depth 34˚ 12. 343' N 134˚ 34. 213' W E W Range marker CSE SPD 357˚ 9.9 kt DEP TMP 35 m 12.3˚C CUR 11.0˚ CUR 11.0˚ 2.0 kt 2.0 kt GAIN 5.3 Event marker Position in latitude*, longitude* Course*, speed* Depth, water temperature* Tide direction*, tide speed* Gain setting SE Cursor SW 16 B234˚ Event marker data 9 8 B7˚ S TVG LEVEL 4.0 DISTANCE 200 m COLOR Color bar * Requires appropriate sensor. Range and bearing markers data Ship's track* Current vector* Sweep indicator (Shows train position in horizontal mode.) TVG level, distance settings North marker* N NW NE W E SWS SE Figure 2-2 Typical horizontal mode display With the tilt angle lowered, your ship is at the center, the bottom, which appears in reddish-brown color, is displayed as a circle and fish echoes appear within the circle. 2-2 2.3 Selecting the Range The [RANGE] control selects the detection (display) range. Select the range according to either the fish species being searched or the depth desired. 15 ranges are available and minimum and maximum ranges depend on the transducer used. SEA SURFACE SEA SURFACE BOTTOM BOTTOM Range indicated onRange the screen. indicated on the screen. Figure 2-3 How to select the range Default horizontal mode range settings Range No.1 No.2 No.3 No.4 No.5 No.6 No.7 No.8 No.9 No.10 No.11 No.12 No.13 No.14 No.15 60 kHz m 10 20 40 80 120 160 200 250 300 400 500 600 800 1200 1600 ft 40 80 120 200 300 400 500 600 800 1000 1500 2000 3000 4000 5000 88 kHz m ft 10 40 20 80 40 120 80 200 120 300 160 400 200 500 250 600 300 800 400 1000 500 1500 600 2000 800 2500 1000 3500 1200 4000 150 kHz m ft 10 40 20 80 40 120 60 200 80 300 120 400 160 500 200 600 250 700 300 800 400 1000 500 1500 600 2000 800 2500 1000 3500 180 kHz m ft 10 40 20 80 40 120 60 200 80 300 100 400 120 500 160 600 200 700 250 800 300 1000 400 1200 500 1500 600 2000 800 2500 240 kHz m ft 10 30 20 60 30 90 40 120 60 150 80 200 100 250 120 300 160 400 200 500 250 600 300 800 400 1000 500 1500 600 2000 Normally the range is set so that the bottom is traced at the lower part of the screen (like an echo sounder). Each time the [Range] control is operated the newly selected range briefly appears in large characters at the screen top. Range is always displayed at the right-hand corner of the screen. Note 1: Unit of range measurement may be selected for meters, feet, fathoms, passi/braza or Hiro (Japanese) with UNIT on the SYSTEM SETTING 1 menu. For details see page 5-10. Note 2: Ranges may be freely preset as desired. For details see page 5-14. 2-3 2.4 Selecting Sector Width Sector means the width of the transducer training. Display sector (shown: 96˚) 96° Figure 2-4 Display sector The [SECTOR] control selects the training (display) area among the sixteen positions shown in the table below. Clockwise rotation of the control increases the sector width; counterclockwise rotation decreases it. Sector width (°) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 6 24 48 72 96 120 144 168 192 216 240 264 288 312 336 360 In the full-circle mode (360°) the direction of training is clockwise; in the half-circle mode the direction is clockwise to counterclockwise alternately. One-touch selection of 360°° sector Each pressing of the [FULL/HALF] key alternately selects 360° sector (full circle) or 168° sector (half circle). If the [SECTOR] control is operated following the selection of the full-circle display, the next pressing of the [FULL/HALF] key presents the full-circle display. Sector set with SECTOR control Full circle FULL/HALF key Half circle FULL/HALF key Figure 2-5 How the FULL/HALF key works 2-4 168° 2.5 Selecting Train Center The [TRAIN] control selects the center direction of the detection range. The range of adjustment is 0° to 354° in increments of 6°. The selected bearing is shown with a filled circle, the train indicator, on the bearing scale. 0˚ (360˚) → 6˚ → 12˚ → 18˚ → ... 354˚ Train indicator Sector Figure 2-6 Train center 2.6 Selecting the Tilt Angle The tilt angle shown the direction to which the sound wave is emitted. When the sound wave is emitted horizontally, the tilt angle is Sounding beam +5˚ 0˚ Horizontal direction said to be 0° and when emitted vertically, 90°. To set a tilt angle, operate the [TILT] control. Watch the tilt angle indication and tilt angle indicator at the top right corner of the screen. Transducer Tilt angle setting range 90° Vertical direction The tilt angle can be set in increments of 1° from 0° to +5° (upward) to 0° to 90° (downward). Select tilt angle depending on target fish. For surface fish select a narrow angle (about 5°) and for bottom fish, a wide angle (about 40°). 2-5 2.6.1 Bottom echo and tilt angle Refer to the illustration below. Case1: Tilt angle 30°° to 40°° This tilt angle will display the entire bottom since it is captured by the full width of the beam. Case2: Tilt angle 10°° to 20°° This tilt angle will only display half the bottom since it is only captured by the lower half of the beam. Case3: Tilt angle 0°° to 5°° This tilt angle may or may not capture the bottom since the returning echo is weak. 2.6.2 How to discriminate fish echoes from the bottom The figure at the bottom of the page illustrates how two fish schools “a” and “b” are displayed on the screen using three different tilt angles. Case 1(Tilt angle 30°° to 40°): Fish school is obscured by the bottom. Case 2(Tilt angle 10°° to 20°): Fish school is located above the bottom (midwater). Case 3(Tilt angle 0°° to 5°): Case 1 Fish school is located close to the bottom. Case 3 Case 2 Fish school "a" Fish school "a" Fish school "a" Bottom Fish school "b" Bottom Bottom Fish school "b" Fish school "b" Case 1 Case 2 Figure 2-7 Fish echo and tilt angle 2-6 Case 3 Points to consider Normally, a vertically distributed fish school is a better sonar target than the bottom, because it reflects the transmitted pulse back toward the transducer. In case 3, both fish schools “a” and “b” are presented. Generally speaking, however, midwater fish schools tend to be larger than bottom fish schools and they are often displayed near the bottom on the display. It is difficult to detect bottom fish when they are not distributed vertically. 2.6.3 Tilt angle for surface fish Sound emitted from the sonar transducer forms an oval-shaped beam with a width of approximately 12° (for 60 kHz transducer at –3 dB) in the vertical direction (vertical beam width). The tilt angle is indicated by the angle between the center line is parallel with the sea surface and one half of the emitted sound goes upward, toward the sea surface. This causes one half of the emitted sound to be reflected toward the transducer and displayed on the screen as sea surface reflections. When the sea is calm, since the sound is reflected just like reflections become negligible. However if the sea is not calm enough, they will become dominant and interfere with observation of wanted echoes. To minimize these sea surface reflections and to search fish schools effectively, the tilt angle is usually set between 5° and 6° so the upper portion of the beam becomes almost parallel with the sea surface. When the sea is rough, the tilt angle is slightly increased to lessen the affect of sea surface reflections. Sea surface Tilt angle 0° 12° Sea surface Tilt angle 5-7° 12° Figure 2-8 Tilt angle 2-7 2.6.4 Suitable tilt angle The figure below illustrates the relationship among tilt angle, depth and detection range. Refer to it to find out the suitable tilt angle for a given depth/detection range. Tilt angle and beam coverage (frequency 60 kHz, vertical beamwidth 12° at -3 dB) 100 (200) 200 (400) 300 (600) 20(40) 400 (800) Range (m) 0° 5° 40(80) 60(120) 10° 80(160) 15° 100(200) Depth (m) 200(400) Vertical width of sonar beam 300 m 200 m 100 m ° 12 21 m 42 m 63 m Figure 2-9 Tilt angle and beam coverage 2-8 2.7 Selecting the Training Speed The training speed selects how fast the transducer scans the sounding sector. Two choices are available, normal speed (default setting) and high speed, and one may be selected with the [FAST SCAN] key. Each time the key is pressed “NORM” (normal speed) or “FAST” (high speed) momentarily appears at the screen top. Normal (6°) : 60 transmissions required to complete full 360° picture (default setting). High (12°) : 30 transmissions required to complete the full 360° picture. The time necessary to train a full circle depends on range and transducer used. The table below shows the time required to complete one full circle in the horizontal mode using the 150 kHz transducer. Ranges Unit m ft Time required Norm (sec) for one full Fast circle 1 10 40 2 20 80 3 40 120 4 60 200 5 80 300 6 120 400 7 160 500 8 200 600 9 250 700 10 300 800 11 400 1000 12 500 1500 13 600 2000 14 800 2500 15 1000 3500 7 7 7 7 7 10 13 16 20 24 32 40 48 64 81 7 7 7 7 7 9 11 13 15 17 21 25 28 36 45 Note1: Above data for soundome having serial no. 1000 and higher. Note2: The range setting must be at least 160 m to active high speed training, using the 150 kHz transducer. The [FAST SCAN] key is inoperative when the range setting is less than 160 meters. 2.8 Finding Echo Position with the Cursor The cursor measures horizontal range, depth and bearing. Operate the Omnipad to place the cursor where desired. Cursor position data appears at the top left-hand corner on the screen. Cursor position data : Horizontal range : Depth B: Bearing NAV DATA Cursor Figure 2-10 Location of cursor position data 2-9 2.9 Event Marker The event marker functions to mark important locations on the screen, and five event markers may be inscribed. Each time the [EVENT] key is pressed the “latest event marker” (⊕) is inscribed at the cursor location and all previously entered event markers are shown by the “previous event marker” (+). When the capacity for event markers is reached the eldest event marker is erased from the screen to make room for the latest. Note 1: With position data the event marker moves with ship’s movement. The event marker can be inscribed without position data, however it will be stationary. Note 2: The event marker cannot be inscribed from the sub window (strata, history and video plotter displays). It can only be inscribes from the main window. Note 3: Event marker position can be output to external equipment and marked on the display of the external equipment. Each press of the [EVENT] key outputs event marker position. For details see TARGET L/L on page 5-11. Note 4: The tilt angle must be less than 75 degrees to use this feature. 2.9.1 Inscribing the event marker 1. Operate the Omnipad to place the cursor on the location desired for an event marker. 2. Press the [EVENT] key to inscribe the event marker. Event marker data appears at the bottom left-hand corner. "Latest event marker" Display area "Previous event marker" NAV DATA Event marker data →: Horizontal range B: Bearing To delete all event markers, place the cursor outside the display area and press the [EVENT] key. Figure 2-11 How to use the event marker 2-10 2.9.2 Deleting all event markers All event markers can be erased from the screen as follows: 1. Operate the Omnipad to place the cursor outside the display area. 2. Press the [EVENT] key to show the following dialog box. Do the next step within four seconds, otherwise the dialog box will be erased. DELETE EVENT MARK? NO YES to select YES and press the [MENU] key. All event markers are erased from the 3. Press screen. 2.10 Depth and Horizontal Range Markers The horizontal range, depth and bearing to a fish school can be measured by using the range and bearing markers. 1. Operate the Omnipad to place the cursor on the location desired. 2. Press the [R/B] key to display the range and bearing markers. Horizontal range, depth and bearing to the cursor location are shown at the bottom right-hand corner of the screen.. 3. To erase the range and bearing markers, place the cursor outside the display area and press the [R/B] key, or place the cursor on the range or bearing marker and press the [R/B] key. Bearing marker Range marker NAV DATA Range and bearing markers data →:Horizontal range ↓: Depth B: Bearing from ship's bow Figure 2-12 Range and bearing markers 2-11 2.11 Adjusting the Picture 2.11.1 Suppressing bottom and surface reflections In shallow fishing grounds, excessive sea surface and bottom reflections often interfere with wanted fish echoes and they cannot be eliminated sufficiently with the TVG controls. In such cases, try to reduce the output power, without turning down the gain. The picture becomes clearer when output power is reduced rather than when the gain is decreased. 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press COM1 MENU COM2 TX POWER PULSELENGTH TX RATE MAX LONG 10 INT REJECT AGC AUDIO LEVEL OFF OFF 0 : SELECT : CHANGE to select the COM1 menu. HORZ VERT ES PRESET SYS MENU: END Figure 2-13 COM1 menu 3. Press or to select TX POWER and press . The following dialog box appears. TX POWER MAX 4. Press MIN to select MIN. (For long range detection be sure to return the setting to MAX.) 5. Press the [MENU] key to register your selection and close the menu. 2-12 2.11.2 Suppressing bottom tail As described earlier, fish schools near the bottom are sometimes difficult to detect because you have to discriminate fish echoes from the bottom reflections. To discriminate fish echoes near the bottom, select the short Tx pulselength on the COM1 menu to decrease the tail of bottom reflections. 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press 3. Press or to select the COM1 menu. to select PULSELENGTH and press . The following dialog box appears. PULSELENGTH LONG 4. Press SHORT to select SHORT. 5. Press the [MENU] key to register your selection and close the menu. 2.11.3 Displaying weak echoes clearly Echoes from targets (such as the bottom or a fish) return to the transducer in order of the distance to them, and when their intensities are compared at the transducer face, those from nearer targets are generally stronger when their reflecting properties are nearly equal. The sonar operator will be quite inconvenienced if these echoes are directly displayed on the screen, since he won’t be able to judge the actual size of the target from the size of echoes displayed on the screen. To overcome this inconvenience, use the TVG function. It compensates for propagation loss of sound in water: amplification of echoes on short range is suppressed and gradually increased as range increases, so that similar targets are displayed in similar intensities irrespective of the ranges to them. The TVG also functions to suppress unwanted echoes and noise which appears in a certain range area on the screen. Without TVG Noise caused by strong reflection of surface turbulence. Proper TVG setting Nearer target echoes appear Reduce Echoes of equal gain for in larger size. size targets are nearby presented in the areas, same color and size. using Noise is rejected. TVG. Figure 2-14 How TVG works Note: Excessive TVG may eliminate short-range echoes. 2-13 To adjust TVG: 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press COM1 MENU COM2 TVG LEVEL TVG DISTANCE GAIN ADJUST 4.0 4.0 0 RES. COLOR CLUTTER TARGET KEY LOG 0 REVERSE LOCK MODE AUTO TILT AUTO OFF : SELECT : CHANGE to select HORZ. HORZ VERT ES PRESET SYS MENU: END Figure 2-15 HORZ menu 3. Press or to select TVG DISTANCE and press TVG DISTANCE . The following dialog box appears. 4.0 Hi Lo 200 or to adjust TVG distance between 3.0 and 5.0 (130-320 m). As a general rule, 4. Press use a higher setting for low frequency transducer; a lower setting for high frequency transducer. The larger the figure the greater the distance at which TVG works. When you open the TVG dialog box the TVG line changes from solid to dashed and a solid line denotes current TVG setting. TVG Distance Setting Meters Feet Passi/braza Hiro 2-14 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 .... 10.0 3 10 2 2 8 30 5 5 20 70 10 10 40 130 20 20 60 210 40 40 100 330 60 60 130 410 80 80 160 520 100 100 200 660 120 130 250 820 150 170 320 1040 180 210 .... 1000 3280 600 660 .... 5. Press the [MENU] key to register your selection and close the menu. 6. To suppress reflections by the sea surface or plankton, select TVG LEVEL and press . or to adjust TVG LEVEL, considering sea conditions. A setting between 2.0 and 7. Press 5.0 should provide satisfactory results. The higher the figure the less the gain over distance. 8. Press the [MENU] key to register your selection and close the menu. 9. Watch a distant fish echo which is approaching own ship. Adjusting the tilt angle so the fish echo is within the sounding beam. Observe color of fish echo. If the color and size of the echo stay the same as the echo approaches own ship, the TVG setting is proper. If the echo suddenly becomes smaller, the TVG level may be too high. 2.11.4 Erasing weak echoes Weak echoes such as interfere can be erased from the screen. This is useful when you want to observe a fish school echo. 1. Press the [MENU] key to open the menu. 2. Press to select MENU. 3. Press to select COM2. 4. Press or 5. Press to open the dialog box. to select SIG LEVEL. SIG LEVEL OFF 1 OFF 14 (OFF, 1-14) 8-color display: OFF, 1-6 16-color display: OFF, 1-14 or to select echo color to erase. Pressing erases echoes from weak to 6. Press strong in ascending order of strength. You can also see which echo color is erased by watching the color bar. 7. Press the [MENU] key to register your selection and close the menu. 2-15 2.11.5 Enlarging fish echoes (expand horizontal display) Fish echoes may be enlarged 1.5 times by using the expanded horizontal display. Press the key to show the expanded horizontal display. The direction of expansion depends on the train direction as below. Train center direction Position after expansion Remarks 318° –42° Moves to screen bottom For viewing forward 48° –123° Moves to left side of screen For viewing starboard side 138° –222° Moves to screen top For viewing aft 228° -312° Moves to right side of screen For viewing port side Sector marker Cursor position data Tilt angle Train indicator Range →14 ↓ 12 B46° + R T 40 m 40° 30 25 Train position 34° 12. 343' N 134° 34. 213' W CSE SPD 357° 9.9 kt DEP TMP 35 m 12.3˚C CUR 11.0˚ 11.0° CUR 2.0 kt 2.0 kt GAIN 5.3 Own ship marker TVG LEVEL 4.0 DISTANCE 200 m COLOR Cursor Figure 2-16 Expanded horizontal display 2-16 2.12 Target Lock Three types of target lock modes are available. Manual reverse: The transducer train direction is reversed manually. This is the default setting, and is available in the horizontal and vertical fan modes. Position: Tracks stationary position (such as a reef) using position data from a navigator. Available in the horizontal mode only. Echo: Tracks fish echo either manually or automatically. Available in the horizontal mode only. 2.12.1 Setting target lock mode 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press 3. Press or 4. Press to show following dialog box. or to select the HORZ menu. to select TARGET KEY. TARGET KEY REVERSE 5. Press or POS ECHO to select option desired. 6. Press the [MENU] key to register your selection and close the menu. 2.12.2 Manual reverse mode The transducer train direction is reversed manually, thereby emphasizing possible fish echoes. Note: This function is inoperative in the echo sounder mode. In the vertical fan mode the manual reverse mode is automatically selected regardless of the setting in paragraph 2.12.1. To activate the manual reserve mode: 1. Select REVERSE following the procedure in paragraph 2.12.1. 2. Press the [TARGET] key to reverse the transducer train direction when a fish school appears. “REVERSE” momentarily appears at the screen top when the key is pressed and then the transducer train direction is reversed. 2-17 2.12.3 Position mode This mode tracks a stationary position (such as a reef) using position data fed from a navigator. Note1: This function is inoperative in the echo sounder mode. In the vertical fan mode the reverse mode is automatically selected regardless of the setting in paragraph 2.12.1. Note2: This mode requires position data. When there is no position data the message “NO POSITION DATA.” appears for five seconds and tracking is automatically cancelled. Check the navigator. Note3: The tilt angle must be less than 75 degrees to use this feature. To use the position mode: 1. Select POS following the procedure in paragraph 2.12.1. 2. Use the Omnipad to select the location to track. 3. Press the [TARGET] key. The message “POS LOCK” appears momentarily at the screen top, the target lock marker is displayed at the cursor position and the target lock indicator appears at the top right-hand corner of the screen while tracking (with position data from external equipment) is occurring. If the position goes out of the display area target lock is automatically cancelled and the target lock indicator and target lock marker disappear. The SECTOR, TILT and TRAIN controls are inoperative since they are automatically adjusted. Target lock indicator Target lock marker Figure 2-17 Target lock indicator 4. To turn off the target lock, press the [TARGET] key again. The message “LOCK END” momentarily appears, the target lock marker and the target lock indicator disappear and previously used sector, train and tilt settings are restored. Also, latitude and longitude indication returns to normal. 2-18 2.12.4 Echo mode The echo mode tracks a fish school either automatically or manually. The default setting is automatic, and you can select automatic or manual with “LOCK MODE” in the HORZ menu. Automatic echo tracking mode The automatic echo target lock function automatically tracks a fish school appearing in the operator-selected target lock zone. If the tracked fish school goes out of the zone in the range direction, tracking is suspended until it or a new fish school comes into the zone. To use the automatic echo tracking mode: 1. Select ECHO following the procedure in paragraph 2.12.1. 2. If necessary select LOCK MODE to AUTO (default setting ) on the HORZ menu. 3. Press the [TARGET] key. The dialog box below appears at the screen center, the message “ECHO LOCK” appears for three seconds at the top of the screen, the target lock area appears in the current train area and the target lock indicator appears at the right-hand side of the screen. TARGET LOCK AREA. : INSIDE : OUTSIDE 4. Use the [SECTOR] and [TRAIN] controls and the Omnipad to set the detection area. Do not include bottom echoes in the zone, so that target lock will not be activated by bottom echoes. When a target of red or reddish-brown color is detected in the zone, the target lock indicator blinks and a buzzer sounds to call the operator’s attention. The [SECTOR], [TILT] and [TRAIN] controls are inoperative since they are automatically adjusted. When you attempt to operate shoes controls the message “TARGET LOCKING NOW.” appears. Outer limit Target lock indicator NAV DATA Inner limit Figure 2-18 Target lock area 2-19 When the fish echo is lost the tilt angle is automatically changed as below to continue tracking the echo: Tilt changed to search [(A + 10˚) → (A - 10˚) →A] Detection area displayed once again and target lock indicator lights. A: Tilt angle at start of target lock 5. To turn off the target lock, press the [TARGET] key again. The message “LOCK END” appears for three seconds at the screen top, the target lock indicator disappears and operation continues with current train and tilt settings. Manual echo tracking mode 1. Select ECHO following the procedure in paragraph 2.12.1. 2. Select LOCK MODE to MANUAL on the HORZ menu. 3. Press the [TARGET] key when a wanted target echo appears. The message “ECHO LOCK” appears along with the target lock indicator. Then, the transducer train direction is reversed and searching starts with the current tilt angle. When a target echo appears the transducer train direction is again reversed automatically, the buzzer sounds and the target lock indicator blinks. If the fish echo is lost the tilt angle is automatically changed to continue tracking as below. 1. Tilt angle is changed by +10˚ (A+10˚). (A is the tilt angle used when tracking began.) 2. Tilt angle is changed by -10˚ (A-10˚). 3. If the echo could not be found, tracking is cancelled and tilt angle A is restored. 4. To quit the target lock, press the [TARGET] key again. The message “LOCK END” appears momentarily. 2-20 2.13 Horizontal Menu Overview This section presents an overview of the items on the HORZ menu. 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press COM1 MENU COM2 TVG LEVEL TVG DISTANCE GAIN ADJUST 4.0 4.0 0 RES. COLOR CLUTTER TARGET KEY LOG 0 REVERSE LOCK MODE AUTO TILT AUTO OFF : SELECT : CHANGE or to select the HORZ menu. HORZ VERT ES PRESET SYS MENU: END Figure 2-19 HORZ menu 3. Press or to select item desired. 4. Press to show corresponding dialog box. 5. Press or to select option desired. 6. Press the [MENU] key to register your selection and close the menu. 2.13.1 Horizontal menu description TVG LEVEL: Compensates for propagation loss of sound in water. Default setting is 4.0. For further details, see paragraph 2.11.3 on page 2-13. TVG DISTANCE: As above. Default setting is 4.0. GAIN ADJUST: Compensates for too weak or too strong echo level. Adjust it when the gain on the horizontal mode when it is not the same as that on the vertical fan and echosounder modes. Setting range: -10 to +10. Default setting is 0. 2-21 CLUTTER: Low intensity echoes, often caused by sediments in water, are painted on the screen as a large number or random dots. This noise can be suppressed. The higher the number (setting) the weaker the echoes which are erased. RES. COLOR: Sets transfer characteristics of input signal level versus display echo level. Echo strength is emphasized in order of CUBE, SQUARE, LINEAR, LOG, and you can observe the characteristics of each by watching the color bar as you change the setting. LOG: Displays weak to strong echoes in their respective levels. This is the default setting, and is suitable for general use. LINEAR: Downplays the weak echoes when compared with LOG. Effective for suppressing weak echoes such as plankton. SQUARE: Strong echoes are emphasized more than in LINEAR. CUBE: Strong echoes are emphasized even more than in SQUARE. TARGET KEY: Selects target lock function among reverse, position and echo. Default setting is REVERSE. For further details see paragraph 2.12 on page 2-17. LOCK MODE: Selects how to track fish echo in ”echo” target lock; automatically or manually. Default setting is AUTO. For further details see paragraph 2.12 on page 2-17. AUTO TILT: Turns automatic tilt on or off, and the default setting is OFF. The choices are ±2°, ±4°, ±6°, and ±10°. Automatic tilt adjusts the tilt angle in the following sequence: B → (B-A) → B → (B+A) → B → (B-A) → B → (B+A)… B: Current tilt angle A: Auto tilt setting For example, the tilt angle is 30° and the automatic tilt setting is 4°. Then, the tilt angle is changed in the following sequence: 30° → 26° → 30° → 34° → 30°→ 26° → 30° → 34°… Note: The [TILT] control is inoperative when automatic tilt is active. 2-22 2.14 Interpreting the Horizontal Display This section provides information necessary for interpreting the horizontal display. 2.14.1 How the horizontal mode picture is painted The wide sounding beam is emitted from the soundome at a certain tilt angle (see hatched area in the figure below). The information (target echoes) obtained by this beam is displayed in sectors of increments of 12° of the screen. Thus, all directions around the boat are sounded in 30 times of transmissions. Note: When the “FAST SCAN” is switched off, the equipment operates in a narrow sounding beam. Then, the echoes appear on a 6° sector in each transmission, so 60 transmissions are required to complete the full 360° picture (6°x 60=360°). This means that training speed is slower. However, since transmission power is concentrated into the narrow sounding beam, a superior detection range is obtained. Furthermore, since the bottom contour is painted distinctly, bottom fish may be more easily detected. Sounding Beam Screen Display Train: 6˚* Tilt: θ Tilt: θ Sounding Beam When the narrow sounding beam (6˚) is selected 60 transmissions are required to complete the full circle. *12˚ When high speed training is selected. Figure 2-20 How the horizontal mode picture is painted 2-23 2.14.2 Sample echo displays Bottom echoes When the tilt angle is changed, the bottom echo illustrated below will appear on the display. When the tilt is decrease (toward 0°), the bottom trace becomes winder and weaker. By observing the bottom condition on the display, the skipper can prevent net damage. (A) Flat bottom Tilt angle: 10˚ to 15˚ Decreased tilt angle Only half of vertical beam width captures the bottom. (B) Flat bottom Tilt angle: 20˚ or more (C) Sloping bottom Bottom is displayed narrower and in stronger colors when compared to (A). Tilt angle: 20˚ or more Shallow bottom is displayed in a strong color and with a short tail. Bottom The deeper, sloping bottom echo is displayed in a weak color and with a long tail. Figure 2-21 Bottom echoes 2-24 Fish schools A fish school appears as a mass of echoes on the screen. The color of the mass shows the density of fish schools on the sonar beam. To find distribution and center point of a fish school, try several different tilt angles. (A) Sea surface fish Tilt angle: 0˚ to 10˚ Bottom echo not displayed because of decreased tilt angle. Sea surface reflections are present. Fish school Sea surface reflections (B) Midwater, bottom fish Tilt angle: 30˚ or more Fish echo which appears before bottom can be detected. Bottom Fish school Large midwater fish school is present. Tilt angle: 0˚ to 20˚ Fish echo which appears together with or after bottom can be detected. Fish school Bottom When the tilt angle is shallow, the reflection echo from bottom is weak and the fish echo which appears from bottom is easy to find. Figure 2-22 Fish schools 2-25 Sea surface reflections To reduce sea surface reflections, set the tilt angle to 5° or higher, so the upper edge of the sonar beam does not hit the sea surface, or adjust TVG. When a decreased tilt angle is used, sea surface reflections cover a large area as illustrated below. Sea surface Tilt angle indication 17˚ Sea surface reflections Sea surface 17˚ Figure 2-23 Sea surface reflections Wake A wake produced by own ship or another ship can be a strong reflecting object when a decreased tilt angle is used. As the wake appears as a thick continuous line, it can be easily distinguishes from a fish school. A wake contains many air bubbles which attenuate ultrasonic energy, making it difficult to sound beyond the wake. Other ship Own ship Own ship's screw noise Wake produced by other ship Own ship's screw noise Figure 2-24 Wake 2-26 Own ship's wake (produced when own ship turned) Sidelobe echo (false echo) An ultrasonic wave is emitted only in the direction set by the [TILT] control, however there are some emissions outside the main beam. These are called sidelobes. The energy of the sidelobe is fairly weak but when the water is comparatively shallow and the bottom is rocky and hard, strong signals are detected by the sidelobe. These are represented on the display as a false echo as shown below. Mainlobe echo Sidelobe echo Sidelobe Mainlobe The bottom echo detected by sidelobe appears at a certain tilt angle when the sidelobe points vertically. Also, poor soundome projection may result in a similar false echo. Figure 2-25 Sidelobe echoes Noise and interference When the fishing ground is crowded with many fishing boats, the sonar is subject to interference from ultrasonic equipment (echo sounder or sonar) on other boats as well as those on own ship. For instance, interference from the sonar operated on other boats will show itself on the display as in (A) in the figure below. This interference can be suppressed by changing the Tx rate on the COM1 menu. Noise from marine life shows itself on the displays as in (B) in the figure below. This type of noise can be suppressed with the interference rejector on the COM1 menu. (A) Inteference from other sonars (yours or other's) (B) Interference from marine life Figure 2-26 Noise and interference 2-27 2.14.3 Combination display examples Horizontal/history display Press the key to display the horizontal/history display. Tilt angle Cursor position data Tilt angle indicator Range →17 ↓ 14 B148˚ + R 40 m T 40˚ 30 Interference rej. ON Target lock indicator 25 Own ship marker 34° 12. 343' N 134° 34. 213' W CSE 357˚ SPD 9.9 kt Train position Transducer status indicator Position in latitude*, longitude* Course*, speed* Fish echo Bottom echo Cursor * Requires appropriate sensor input. Horizontal Display HIstory Display Figure 2-27 Horizontal/history display The horizontal display appears in the main window; the history display in the sub window. The length of the picture displayed in the history display is equal to about four full circle pictures. Thus the history display enables you to observe the history of fish movement and distribution. It is also useful for detecting bottom fish, reefs and sunken vessels. The history display cannot be adjusted. 2-28 Horizontal/video plotter display Press the key to display the horizontal/video plotter display. Tilt angle Cursor position data Tilt angle indicator Range →18 ↓ 15 B154˚ + R 40 m T 40˚ 30 Interference rej. ON Target lock indicator 25 Transducer status indicator Own ship marker 34° 12. 343' N 134° 34. 213' W Train position CSE 357˚ SPD 9.9 kt Track* Position in latitude*, longitude* Course*, speed* Sonar range marker (Radius changes with video plotter range.) Event marker (Entered from horizontal mode) Event marker Cursor →15 B 195° Event marker data 500 * Requires appropriate sensor. Horizontal Display Scale Track* Video Plotter Display Figure 2-28 Horizontal/Video Plotter display The horizontal display appears in the main window; the video plotter display, which traces ship’s track on the display, in the sub window. Compared to the horizontal display the video plotter’s range is much longer. For example, an event marker entered on the horizontal display disappears from that display when it goes out of the current range. However, it remains on the video plotter display for a much longer time when a long range scale is used. This can be useful when you want to return to the location denoted with an event marker. To display track on the horizontal display, the tilt angle must be less than 75 degrees. You may switch control between the horizontal display and the video plotter display with the [MAIN/SUB] key. The message MAIN WINDOW CONTROLLABLE or SUB WINDOW CONTROLLABLE appears with each pressing of the key. A red rectangle circumscribes the sub window when it is selected. With the video plotter display selected you may change its range with the [RANGE] control. Note: Controls other than RANGE may only be operated from the main window. When you attempt to operate them when the sub window is selected the message SELECT MAIN WINDOW appears. The video plotter display cannot be adjusted. 2-29 Horizontal/strata display Press the key to display the horizontal/strata display. Tilt angle Cursor position data Tilt angle indicator Range →12 ↓ 10 B133˚ + R 40 m T 40˚ 30 Interference rej. ON Target lock indicator 25 Own ship marker Transducer status indicator 34° 12. 343' N 134° 34. 213' W CSE 357˚ SPD 9.9 kt Train position PORT Position in latitude*, longitude* Course*, speed* STBD Number of lines increases by one with each train. Top line is latest; bottom line is oldest. Color bar for strata display * Requires appropriate sensor input. Cursor -90° Horizontal Display (main display) 0° Heading +90° Strata Display (sub window) Figure 2-29 Horizontal/strata display The horizontal display appears in the main window; the strata display in the sub window. The strata picture shows bottom undulations in different colors. This is useful in bottom trawling to avoid projections which may damage the net. Coverage for the horizontal mode is 360° picture, and for the strata display it is maximum 90° from port to 90° starboard. The strata display may be adjusted with the [RANGE] and [SECTOR] controls. Press the [MAIN/SUB] key to select the main or sub window. The message MAIN WINDOW CONTROLLABLE or SUB WINDOW CONTROLLABLE appears with each pressing of the key. A red cursor appears in the sub window when it can be controlled. 2-30 Color bar for the strata display The depth of the bottom each in all directions is displayed in the sub window, in the colors set by the color bar for the strata display. The color bar for the strata display shows search angle range below 336 degrees. Strongest color Weakest color -90˚ -18˚ -12˚ -6˚ 0˚ 6˚ 12˚ 18˚ 90˚ The undulation of the bottom echo in all directions is shown by the colors on the color bar for the strata display. Color bar for strata display The position of the weakest echo can be changed with the [RANGE] control, and the width of each color on the color bar for the strata display with the [SECTOR] control. Use the [SECTOR] control to adjust width of each color. Weakest color Use the [RANGE] control to move the location of the weakest echo color. Note: TILT, TRAIN, FULL/HALF, FAST SCAN, R/B, EVENT, TARGET, CUSTOM MODE controls may only be operated from the main window. When you attempt to operate them from the sub window the message “SELECT MAIN WINDOW.” appears for about four seconds. Flat bottom and strata display Each layer on the strata display is equal to one train on the horizontal display. -90˚ PORT STBD +90˚ Color "a" on the color bar When the bottom is flat the horizontal display inscribes the bottom as a true circle, and the strata display inscribes the color of point "a". Color "a" The color of this position on the color bar is the color of point "a" on the strata display. Figure 2-30 Flat bottom and strata display 2-31 Projection in fore direction and strata display Color "b" on the color bar is displayed here. -90˚ Color "b" PORT STBD +90˚ Color "a" on the color bar Color "a" Figure 2-31 Projection in fore direction and strata display Depth becoming shallower gradually in fore direction and strata display Color "c" -90˚ Color "b" PORT STBD +90˚ Color "a" Color "b" Color "d" Color "a" "a" Color Color "c" Figure 2-32 Depth becoming shallower gradually in fore direction and strata display Depth becoming deeper gradually in fore direction and strata display a -90˚ b c d c b Color "a" +90˚ Color "b" Color "d" Color "a" Color "c" Figure 2-33 Depth becoming deeper gradually in fore direction 2-32 3. VERTICAL FAN MODE 3.1 Operational Overview The figure below shows the typical vertical fan mode operating sequence. 6. Set center bearing of train sector. 7(a). Set scanning sector. 1. Turn on the power. 8. Set tilt angle. 5. Set range. 11. Adjust menu settings 9. Adjust gain. (ex. TVG) as required. XDR GAIN SECTOR POWER DISPLAY MODE RANGE TRAIN TILT MAIN FULL FAST SUB HALF SCAN BRILL TARGET MENU R/B EVENT CUSTOM MODE 2. Lower the transducer. 4. Select appropriate vertical fan mode. 7(b). Select training sector 180˚. 10. Measure range and bearing to target with cursor. 3. Adjust screen brilliance. Figure 3-1 Control panel 3-1 3.2 Typical Vertical Fan Mode Display Bearing indicator (Shows training direction.) FORE Own ship PORT STARBOARD AFT Vertical range Horizontal range Training indicator Interference rejector ON Transducer status indicator Filled arrow: Respective action completed Blinking arrow: Action in progress Heading* Cursor position data Horizontal range scale +→6 ↓ 145 60 R → 60 m ↓ 100 m 340˚ FORE AFT 60 34° 12. 343' N 134° 34. 213' W Fish echo Cursor CSE SPD Horizontal range DEP Bottom echo 20 Depth TMP 56 Horizontal marker CUR 100 Sector center indicator Event marker Sweep indicator (Shows tilt angle in vertical fan mode.) 35 m 12.3˚C 11.0˚ 2.0 kt GAIN 5.3 TVG LEVEL 4.0 DISTANCE 200 m COLOR Vertical range scale Horizontal range marker Figure 3-2 Typical vertical fan mode display 3-2 357˚ 9.9 kt Position in latitude*, longitude* Course*, speed* Depth Water temperature* Tide direction*, tide speed* Gain setting TVG level, distance settings Color bar * Requires appropriate sensor. 3.3 Selecting the Range The [RANGE] control selects the detection (display) range, in 15 settings. Select the range according to either the fish species being searched or the depth desired. Each time the control is operated the newly selected range briefly appears in large characters at the screen top. Range is permanently displayed at the top right-hand corner of the screen. Normally the range is set so that the bottom is traced at the lower part of the screen (like an echo sounder). Surface RANGE m Bottom Figure 3-3 Range concept Default vertical fan mode range settings Unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Meters 10 20 30 40 60 80 100 120 160 200 250 300 400 500 600 Feet 30 60 90 120 150 200 250 300 400 500 600 800 1000 1500 2000 Note 1: Unit of range measurement may be selected for meters, feet, fathoms, passi/braza or Hiro (Japanese) with UNIT on the SYSTEM SETTING 1 menu. For details see page 5-10. Note 2: Ranges may be freely preset as desired. For details see page 5-16. 3-3 3.4 Selecting Train Center The [TRAIN] control determines the bearing of the vertical fan beam, from 0° to 180°. Bearing of beam position can be found with the train indicator. 0˚ (360˚) → 6˚ → 12˚ → 18˚ → ... 180˚ Train Indicator Train of Vertical Fan Beam Train indicator Bow TRAIN Figure 3-4 Train indicator Train 0˚ Train 90˚ FORE Train 180˚ STBD Figure 3-5 Train indicator and display 3-4 AFT 3.5 Selecting Display Sector Sector means the width of the transducer training, from 6° to 180°. Sector (Shown: 24˚) 24˚ Figure 3-6 Sector The [SECTOR] control selects the training area among the sixteen positions shown in the table below. Clockwise rotation of the control increases the sector width; counterclockwise rotation decreases it. Sector width (°) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 6 12 24 36 48 60 72 84 96 108 120 132 144 156 168 180 One-touch selection of 180°° sector 1. Press the [FULL/HALF] key. A half-circle display of 180° is presented. 2. Press the [FULL/HALF] key again, and a 120°-sector display is presented. Note: Operating the [SECTOR] control between steps 1 and 2 in the procedure above displays the 180° sector at the next pressing of the [FULL/HALF] key. Sector set with SECTOR control Half circle FULL/HALF key 0˚ 180˚ FULL/HALF key 0˚ 180˚ 180˚ 120˚ 24˚ Figure 3-7 How the FULL/HALF key works 3-5 3.6 Selecting Sector Center The center direction of the sounding beam in the vertical direction can be changed with the [TILT] control. The setting range is 0° to 180° in increments of 6°. Select the setting which places the sector center in the middle of the detection range. Sector center angle set with TILT control PORT In the example display at left, the sector center indicator is starboard, and the width of the sector is 48˚. STBD 0˚ Sector range 180˚ Sector center indicator Sector of 48˚ set with [SECTOR] control Figure 3-8 Sector center Automatic shifting of own ship position Own ship position on the screen is automatically shifted either rightward or leftward according to the direction of the sector center and display sector width. The figure below shows the own ship position has been shifted rightward on the screen to provide the wider view at the port side. Sector center 0° to 60°: Own ship position shifted to port side Sector center 66° to 114°: Own ship position shifted to center Sector center 120° to 180°: Own ship position shifted starboard Display sector Sector center Figure 3-9 How automatic shifting works 3-6 3.7 Selecting the Training Speed The training speed selects how fast the transducer scans the display sector. Two choices are available, 3° (normal speed, default setting) and 6° (high speed), and one may be selected with the [FAST SCAN] key. Each time the key is pressed the display momentarily shows “NORM” (normal speed) or “FAST” (high speed). Normal: 60 transmissions for half circle in increments of 3°. High: 3.8 30 transmissions for half circle in increments of 6°. Finding Echo Position with the Cursor The cursor measures horizontal range and depth. Operate the Omnipad to place the cursor where desired. Cursor data appears at the top left-hand corner on the screen. Cursor data +→ : Horizontal range ↓: Depth NAV DATA Cursor Figure 3-10 Location of cursor position data 3-7 3.9 Event Marker The event marker functions to mark important locations on the screen, and five event markers may be inscribed. Each time the [EVENT] key is pressed the “latest event marker” (⊕) is inscribed at the cursor location and all previously entered event markers are shown by the “previous event marker” (+). When the capacity for event markers is reached the eldest event marker is erased from the screen to make room for the latest. Note 1: Event marker position can be output to external equipment and marked on the display of the external equipment. Each press of the [EVENT] key outputs event marker position. For details see TARGET L/L on page 5-11. Note 2: Event markers cannot be inscribed from the vertical fan display when it is in the sub window (Horizontal/vertical fan display). Inscribe the marker from the horizontal display to show it in the vertical fan display. 3. Operate the Omnipad to place the cursor on the location desired for an event marker. 4. Press the [EVENT] key to inscribe the event marker. The event marker is inscribed on the vertical fan display, as well as the horizontal and video plotter displays. "Previous event marker" Display area NAV DATA "Latest event marker" To delete all event markers, place cursor outside display area and press the [MENU] key. Figure 3-11 How to inscribe, delete the event markers 3-8 3.9.1 Deleting all event markers All event markers can be erased from the screen as follows: 4. Operate the Omnipad to place the cursor outside the display area. 5. Press the [EVENT] key to show the following dialog box. Do the next step within four seconds, otherwise the dialog box will be erased. DELETE EVENT MARK? NO YES to select YES and press the [MENU] key. All event markers are erased from the 6. Press screen. 3.10 Depth and Horizontal Range Markers The depth and horizontal range markers function to measure the horizontal range and depth to a desired echo. Note: Depth and horizontal range markers cannot be inscribed from the vertical fan display when it is in the sub window (Horizontal/vertical fan display). Inscribe the markers from the horizontal display to show it in the vertical fan display. 1. Operate the Omnipad to place the cursor on the location desired. 2. Press the [R/B] key to display the depth and horizontal range markers. Horizontal range and depth appear on the screen. 3. To erase the depth and horizontal range markers, press the [R/B] key again, or place the cursor on the depth or horizontal range marker and press the [R/B] key. Horizontal range NAV DATA 94 Horizontal range marker 105 Depth Depth marker Figure 3-12 Depth and horizontal range markers 3-9 3.11 Adjusting the Picture 3.11.1 Displaying weak echoes clearly Echoes from targets (such as the bottom or a fish) return to the transducer in order of the distance to them, and when their intensities are compared at the transducer face, those from nearer targets are generally stronger when their reflecting properties are nearly equal. The sonar operator will be quite inconvenienced if these echoes are directly displayed on the screen, since he won’t be able to judge the actual size of the target from the size of echoes displayed on the screen. To overcome this inconvenience, use the TVG function. It compensates for propagation loss of sound in water: amplification of echoes on short range is suppressed and gradually increased as range increases, so that similar targets are displayed in similar intensities irrespective of the ranges to them. The TVG also functions to suppress unwanted echoes and noise which appears in a certain range area on the screen. To adjust TVG: 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press COM1 MENU COM2 TVG LEVEL TVG DISTANCE 4.0 4.0 GAIN ADJUST RES. COLOR CLUTTER HORZ RANGE 0 LOG 0 x1 : SELECT or to select the VERT menu. HORZ VERT : CHANGE ES PRESET SYS MENU: END Figure 3-13 VERT menu 3. Press or to select TVG DISTANCE and press TVG DISTANCE GAIN Hi Lo 3-10 200m to show the following dialog box. 4.0 4. Press or to adjust TVG distance, considering sea conditions. The larger the figure the greater the distance at which the TVG works. TVG Distance Setting Meters Feet Passi/braza Hiro 5. Press or 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 .... 10.0 3 10 2 2 8 30 5 5 20 70 10 10 40 130 20 20 60 210 40 40 100 330 60 60 130 410 80 80 160 520 100 100 200 660 120 130 250 820 150 170 320 1040 180 210 .... 1000 3280 600 660 .... to close the dialog box and return to the VERT menu. 6. To suppress reflections by the sea surface or plankton, select TVG LEVEL and press . or to adjust TVG LEVEL, considering sea conditions. The larger the figure the 7. Press less the gain over distance. 8. Press the [MENU] key to register your selection and close the menu. Wrong Correct Level too high Distance too high Figure 3-14 Examples of proper and improper TVG 3.11.2 Suppressing noise and interference You may encounter occasional or intermittent noise and interference as shown below. This is mostly caused by electrical equipment, engine, propeller noise from own ship, or noise from other sonars being operated nearby. If interference appears, turn on the interference rejector in the COM1 menu to suppress it. Interference rejector ON Interference (In this display, interference shows itself every 6˚.) Figure 3-15 Appearance of interference 3-11 3.12 Vertical Menu Overview This section presents an overview of the items on the VERT menu. 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press COM1 MENU COM2 TVG LEVEL TVG DISTANCE GAIN ADJUST 4.0 4.0 0 RES. COLOR CLUTTER HORZ RANGE LOG 0 x1 : SELECT : CHANGE or to select the VERT menu. HORZ VERT ES PRESET SYS MENU: END Figure 3-16 VERT menu 3. Press or to select item desired. 4. Press to show corresponding dialog box. 5. Press or to select option desired. 6. Press the [MENU] key to register your selection and close the menu. 3.12.1 Vertical menu description TVG LEVEL: Compensates for propagation loss of sound in water. The default setting is 4.0. TVG DISTANCE: As above. Default setting is 4.0. GAIN ADJUST: Compensates for too weak or too strong echo level. Adjust it when the gain on the vertical fan mode is not the same as that on the horizontal and echo sounder modes. Setting range: -10 to +10. Default setting is 0. RES. COLOR: Sets transfer characteristics of input signal level versus display echo level. Echo strength is emphasized in order of CUBE, SQUARE, LINEAR, LOG. You can see the characteristics of each by watching the color bar as you change the setting. Default setting is LOG. LOG: Displays weak to strong echoes in their respective levels. This setting is suitable for general use. LINEAR: Downplays the weak echoes when compared with LOG. Effective for suppressing weak echoes such as plankton. SQUARE: Strong echoes are emphasized more than in LINEAR. CUBE: Strong echoes are emphasized even more than in SQUARE. 3-12 CLUTTER: Low intensity echoes, often caused by sediments in water, are painted on the screen as a large number of random dots. The higher the number (setting) the weaker the echoes which are erased. HORZ RANGE: You may choose the horizontal range expansion factor for the vertical scan picture, from x1 or x2. Note that this feature cannot be adjusted when the vertical search mode, activated by a function key, is turned on. 3.13 Interpreting the Vertical Fan Display This section provides information necessary for interpreting the vertical fan display. 3.13.1 How the vertical fan mode picture is painted The sounding beam is emitted and the information (target echoes) obtained by the beam appears in the corresponding sector as it appears on the sonar mode. The difference is that the training is performed only in vertical direction. It forms a sounding area of a half-circle (like a slice of watermelon) to observe a vertical section of underwater conditions. The bearing of the vertical sounding beam can be selected manually or automatically. Sounding Beam (1) Bearing of the Freq: 60 kHz sounding beam 0° Screen Display (1) Bearing of the sounding beam Bow 180° 180° 0° Sector center 90°. Display range 24°. Tilting direction (2) Sector center (3) Display area (2) Sector center, (3) Display area Select the bearing of the sounding beam (1) by [TRAIN] control, the sounding sector center (2) by the [TILT] control and the display area (3) by the [SECTOR] control. Figure 3-17 How the vertical fan mode picture is painted 3-13 3.13.2 Sample echo displays Port-starboard picture (bottom) You can see fish echoes at the center-right of the screen. The bottom is displayed wider as the distance from the ship’s position increases. Therefore, it may be difficult to discriminate bottom fish. Own ship STBD PORT Fish school Bottom Figure 3-18 Port-starboard picture When ship passes over fish schools The sounding beam is directed fore-aft and the display is off-centered* to present a wider view of the area forward of the ship. You can clearly see fish schools approaching from the bow of the ship. *: Automatically shifted. Own ship Forward FORE AFT Fish school FORE Fish school AFT Figure 3-19 Picture appearance when passing over fish schools 3-14 Display of net hauling This is an example of net hauling display. The location of the net is indicated clearly. FORE AFT Net Figure 3-20 Net hauling and sonar picture False echo In shallow water (depth less than 100 m) detection, unwanted echoes shown in the figure may appear. This phenomenon is caused by the false echo from the previous transmission. Reducing the Tx rate on the COM1 menu may lessen this effect. PORT False echo STBD Bottom Fish Range Figure 3-21 False echoes 3-15 3.13.3 Horizontal/vertical fan display Press the key to display the horizontal/vertical fan display. Tilt angle Cursor data Vertical fan bearing cursor →17 ↓ 14 B156˚ + Tilt angle indicator Range R T 40 m 40˚ 30 Interference rejector ON Target lock indicator 25 Transducer status indicator Own ship marker 34° 12. 343' N 134° 34. 213' W CSE 357˚ SPD 9.9 KT Train position AFT FORE Position in latitude*, longitude* Course*, speed* * Requires navigator. Sweep indicator (tilt angle) Cursor 100 Horizontal Display (main window) Vertical Fan Display (sub window) Figure 3-22 Horizontal/vertical fan display The horizontal display appears in the main window; the vertical fan display in the sub window. The displays are independent of each other so you can adjust them as desired. Press the [MAIN/SUB] key to select the window to adjust. Each pressing of the key momentarily displays MAIN WINDOW CONTROLLABLE or SUB WINDOW CONTROLLABLE at the top of the screen. A red cursor appears in the sub window when it can be controlled. The following controls are operative on either window: SECTOR, TRAIN, RANGE, TILT, FAST SCAN, FULL/HALF and CUSTOM MODE. Note: R/B, EVENT or TARGET controls may only be operated from the main window. When you attempt to operate them from the sub window the message SELECT MAIN WINDOW appears. TRAIN control For horizontal display: Sets training center direction. For vertical fan display: Sets direction of bearing cursor shown on the horizontal mode display. 3-16 SECTOR control For the vertical fan display: When the display sector is 6° (minimum) the tilt angle of the horizontal and vertical fan modes are interlocked and each transmission on the horizontal display is reflected on the vertical fan display. The message TILT ANGLE MONITOR WINDOW momentarily appears on the screen and the vertical bearing cursor disappears. Note: Only the [SECTOR] control may be operated in this condition. The size of the vertical scan and horizontal displays and the location of the vertical scan display may be changed as desired. Press the below. key to change the arrangement as in the figure 3-17 (This page intentionally left blank.) 3-18 4. ECHO SOUNDER MODE 4.1 Operational Overview The figure below shows the typical echo sounder mode operating sequence. 8. Set tilt angle. 7. Select display sector. 5. Set range. 11. Adjust menu settings (turn on A-scope display, etc.). 1. Turn on the power. 6. Adjust gain. XDR GAIN SECTOR RANGE TRAIN POWER DISPLAY MODE TILT MAIN FULL FAST SUB HALF SCAN BRILL TARGET MENU R/B EVENT CUSTOM MODE 2. Lower the transducer. 4. Select echo sounder 10. Measure range to fish school with cursor. mode. 9. Set picture advance speed. 3. Adjust screen brilliance. Figure 4-1 Control panel 4-1 4.2 Typical Echo Sounder Display Press the key to display the echo sounder picture. Tilt angle indicator Bearing (Shows tilt angle of transducer.) indicator (Shows train Tilt angle direction.) Interference rejector ON Range Heading Cursor position + 4 ↓ 340° Transducer status indication R 10 m T 60° Minute marker 34° 12. 343' N 134° 34. 213' W Fish echo Cursor Range CSE SPD 357˚ 9.9 kt CUR 11.0˚ 2.0 kt GAIN 5.3 5 5 Bottom echo TVG LEVEL 4.0 DISTANCE 200 m Position in latitude*, longitude* Course*, speed* Tide direction*, tide speed* Gain setting TVG level, distance settings Color bar 10 DEP 6.5 m Depth (When the tilt angle is 90 deg., the depth measured by this sonar is displayed inside a rectangle.) TMP 12. 3˚C Water temperature* * Requires appropriate sensor. Range marker Range scale Event marker Figure 4-2 Typical echo sounder display 4-2 4.3 Selecting the Range The [RANGE] control selects the detection (display) range, in 15 settings. Select the range according to either the fish species being searched or the depth desired. Each time the control is operated the newly selected range briefly appears in large characters at the screen top. Range is permanently displayed at the top right-hand corner. Normally the range is set so that the bottom is traced at the lower part of the screen. Surface RANGE m Bottom Figure 4-3 Range concept Default echo sounder mode range settings Unit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Meters 10 20 30 40 60 80 100 120 160 200 250 300 400 500 600 Feet 30 60 90 120 150 200 250 300 400 500 600 800 1000 1500 2000 Note 1: Unit of range measurement may be selected for meters, feet, fathoms, passi/braza or Hiro (Japanese). For details see page 5-11. Note 2: Ranges may be freely preset as desired. For details see page 5-17. 4-3 4.4 Train Direction The sounding beam may be directed toward fore, aft, port or starboard. Operate the [TRAIN] control to select sounding beam direction. Each setting on the control is an increment of 6°. The train indicator at the top of the screen shows training direction: 0°, fore direction; 90°, starboard direction; 180°, aft direction, and 270°, port direction. 0˚ (360˚) → 6˚ → 12˚ → 18˚ → ... 354˚ Train 0˚ Train 90˚ Train 180˚ Train 270˚ Figure 4-4 Train indicator and display 4.5 Selecting Tilt Angle The transducer can pointed directly toward the bottom or forward of the ship. Operate the [TILT] control to select an appropriate tilt angle. The available tilt angle is 0° (horizontal direction) to 90° (vertical) in increments of 1°. Selected tilt angle appears at the top of the display to the right of “T”. 4.6 Selecting Picture Advance Speed The picture advance speed determines how quickly the vertical scan lines run across the screen, from right to left. When selecting a picture speed, keep in mind that a fast advance speed will expand a fish school horizontally on the screen and a slow one will contract it. 1. Press the [FAST SCAN] key. The following dialog box appears. Do the next step within four seconds otherwise the dialog box will be erased. ADVANCE 1/8 1/4 1/2 1/1 2/1 or ([FAST SCAN] key may also be used) to select a speed. The fractions in 2. Press dialog box correspond to the number of scan lines produced per transmission. For example, “2/1” means two scan lines are produced per transmission. 3. Press the [MENU] key to close the dialog box. Note that the dialog box is automatically closed if there is no control operation for about four seconds. 4-4 4.7 Measuring Range by Cursor Use the cursor to display the range from own ship to the cursor location. Use the Omnipad to place the cursor where desired. The range to the cursor appears at the upper left-hand corner of the screen. ↓ Range to cursor : Range NAV DATA or A-SCOPE DISPLAY Depth, Water Temp. Display Cursor Figure 4-4 How to measure range with the cursor 4.8 Event Marker The event marker functions to mark important locations on the screen, and five event markers may be inscribed. Each time the [EVENT] key is pressed the “latest event marker” (⊕) is inscribed at the cursor location and all previously entered event markers are shown by the “previous event marker” (+). When the capacity for event markers is reached the eldest event marker is erased from the screen to make room for the latest. Note 1: The event marker inscribed on the echo sounder display will also be inscribed on the horizontal and video plotter displays. However, the mark is always inscribed at own ship position on the horizontal and video plotter displays regardless of the location of the mark on the echo sounder display. Note 2: Event marker position can be output to external equipment and marked on the display of the external equipment. Each press of the [EVENT] key outputs event marker position. For details see TARGET L/L on page 5-11. Note 3: Event markers are automatically erased as they move off the screen with picture advancement. 4-5 4.8.1 Inscribing the event marker 1. Operate the Omnipad to place the cursor on the location desired for an event marker. 2. Press the [EVENT] key to inscribe the event marker. Display area "Previous event marker" NAV DATA or A-SCOPE DISPLAY Depth, Water Temp. Display "Latest event marker" To delete all event markers, place the cursor outside the display area and press the [EVENT] key. Figure 4-5 How to inscribe, delete the event markers 4.8.2 Deleting all event markers All event markers can be erased from the screen as follows: 1. Operate the Omnipad to place the cursor outside the display area. 2. Press the [EVENT] key to show the following dialog box. Do the next step within four seconds, otherwise the dialog box will be erased. DELETE EVENT MARK? NO YES to select YES and press the [MENU] key. All event markers are erased from the 3. Press screen. 4-6 4.9 Range Marker The range marker functions to measure the range to a target echo (fish school, bottom, etc.) 1. Operate the Omnipad to place the cursor on the location desired. 2. Press the [R/B] key to display the range marker. The range marker appears along with range indication. 3. To erase the range marker, press the [R/B] key again, or place the cursor on the range marker and press the [R/B] key. Range marker Range NAV DATA or A-SCOPE DISPLAY 67 Depth, Water Temp. Display Figure 4-6 Range marker 4.10 Adjusting the Picture 4.10.1 Displaying weak echoes clearly Echoes from targets (such as the bottom or a fish) return to the transducer in order of the distance to them, and when their intensities are compared at the transducer face, those from nearer targets are generally stronger when their reflecting properties are nearly equal. The sonar operator will be quite inconvenienced if these echoes are directly displayed on the screen, since he won’t be able to judge the actual size of the target from the size of echoes displayed on the screen. To overcome this inconvenience, use the TVG function. It compensates for propagation loss of sound in water: amplification of echoes on short range is suppressed and gradually increased as range increases, so that similar targets are displayed in similar intensities irrespective of the ranges to them. The TVG also functions to suppress unwanted echoes and noise which appears in a certain range area on the screen. To adjust TVG: 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press or to select the ES menu. 4-7 COM1 MENU COM2 TVG LEVEL TVG DISTANCE GAIN ADJUST RES. COLOR CLUTTER 4.0 4.0 0 LOG 0 A-SCOPE OFF HORZ VERT : CHANGE : SELECT ES PRESET SYS MENU: END Figure 4-7 ES menu 3. Press or to select TVG DISTANCE and press . The following dialog box appears. TVG DISTANCE 4.0 GAIN Hi Lo 4. Press or TVG Distance Setting Meters Feet Passi/braza Hiro 5. Press or 200m to adjust TVG distance. 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 .... 10.0 3 10 2 2 8 30 5 5 20 70 10 10 40 130 20 20 60 210 40 40 100 330 60 60 130 410 80 80 160 520 100 100 200 660 120 130 250 820 150 170 320 1040 180 210 .... 1000 3280 600 660 .... to close the dialog box and return the ES menu. 6. To suppress reflections by the sea surface or plankton, select TVG LEVEL and press 7. Press or to adjust TVG LEVEL. 8. Press the [MENU] key to register your selection and close the menu. 4-8 . 4.10.2 Finding echo strength (A-scope display) The A-scope display shows echoes at each transmission with amplitudes and tone proportional to their intensities on the right 1/4 of the screen. It is useful for estimating the kind of fish school and bottom composition. 1. Press the [MENU] key. 2. Press to select MENU. 3. Press or 4. Press to select A-SCOPE. 5. Press or to select ES. to open the dialog box. A-SCOPE OFF 6. Press ON to select ON. 7. Press the [MENU] key to close the dialog box. Echo sounder picture A-scope display Depth, Water Temp. Display Figure 4-8 A-scope display 4-9 4.11 Echo Sounder Menu Overview This section presents an overview of the items on the ES menu. 1. Press the [MENU] key to open the menu. 2. Press to select MENU and then press COM1 MENU COM2 TVG LEVEL TVG DISTANCE GAIN ADJUST RES. COLOR CLUTTER 4.0 4.0 0 LOG 0 A-SCOPE OFF : SELECT : CHANGE or to select the ES menu. HORZ VERT ES PRESET SYS MENU: END Figure 4-9 ES menu 3. Press or to select item desired. 4. Press to show corresponding dialog box. 5. Press or to select option desired. 6. Press the [MENU] key to register your selection and close the menu. 4.11.1 Echo sounder menu description TVG LEVEL: Compensates for propagation loss of sound in water. See paragraph 4.10.1 on page 4-7. Default setting is 4.0. TVG DISTANCE: As above. Default setting is 4.0. GAIN ADJUST: Compensates for too weak or too strong echo level. Adjust the gain on the echo sounder mode when it is not the same as that on the horizontal and vertical fan modes. Setting range: -10 to +10. Default setting is 0. 4-10 RES. COLOR: Sets transfer characteristics of input signal level versus display echo level. Echo strength is emphasized in order of CUBE, SQUARE, LINEAR, LOG. You can see the characteristics of each by watching the color bar as you change the setting. The default setting is LOG. LOG: Displays weak to strong echoes in their respective levels. This setting is suitable for general use. LINEAR: Downplays the weak echoes when compared with LOG. Effective for suppressing weak echoes such as plankton. SQUARE: Strong echoes are emphasized more than in LINEAR. CUBE: Strong echoes are emphasized even more than in SQUARE. CLUTTER: Low intensity echoes, often caused by sediments in water, are painted on the screen as a large number of random dots. The higher the number (setting) the weaker the echoes which are erased. A-SCOPE: Turns the A-scope display on/off. Default setting is OFF. See paragraph 4.10.2 on page 4-9. 4-11 (This page intentionally left blank.) 4-12 5. MENU OPERATION This chapter provides menu operating information on menus not previously discussed: COM1, COM2, PRESET (or SHORT-CUT, depending on the setting of CUSTOM KEY on the SYSTEM SETTING 1 menu) and SYS (System) menu. 5.1 COM1 Menu 1. Press the [MENU] key to open the menu. 2. Press to select MENU, and then press COM1 MENU TX POWER COM2 HORZ VERT ES PRESET SYS MAX PULSELENGTH LONG TX RATE INT REJECT AGC AUDIO LEVEL 10 OFF OFF 0 : SELECT to select COM1. : CHANGE MENU: END Figure 5-1 COM1 menu 3. Press or to select item; or to open associated dialog box. 4. Press or to select option desired. 5. Press or to return to the COM1 menu, or press the [MENU] key to register your selection and close the menu. 5-1 5.1.1 COM1 menu description TX POWER: Selects transmitter output power to maximum or minimum. The default setting is "maximum." For further details see page 2-12. PULSELENGTH: Selects pulselength to short or long (default setting). For details see paragraph 2.11.2 on page 2-13. TX RATE: The Tx rate may be set between 1-10 (default setting: 10) in the case of the internal transmitter, or an external synchronous signal may be used. The higher the number the greater the number of transmissions. For operation in shallow waters, select the Tx rate which displays the second reflection from the bottom between the sea surface and bottom. For use of an external video sounder or sonar, select EXT. INT REJECT: Turns the interference rejector on or off (default setting). For details, see paragraph 3.11.2 on page 3-11. AGC: Automatically lowers sensitivity against strong echoes such as those from the bottom and large fish schools to emphasize weak echoes such as those from fish close to the bottom. The default setting is OFF. AUDIO LEVEL: Adjusts the audio level of the external loudspeaker (option). 5-2 5.2 COM2 Menu 5.2.1 Displaying the COM2 menu 1. Press the [MENU] key to open the menu. 2. Press ▲ to choose MENU, and then press ◄ or ► to choose COM2. COM1 MENU DELETING TRACK WHITE MARKER SIG LEVEL COM2 HORZ VERT ES PRESET SYS NO OFF OFF COLOR 16 BKGD COLOR 2 BEARING READOUT RELATIVE : SELECT : CHANGE MENU: END COM2 menu 5.2.2 COM2 menu description DELETING TRACK: Choose ON to delete all ship’s track (from horizontal and horizontal/video plotter displays). WHITE MARKER: Displays desired echo in white. It is useful for discriminating bottom fish from the bottom echo. The setting range for the 8-color display is OFF, 1-7, and for the 16-color display, OFF, 1-15. SIG LEVEL: Refer to page 2-17. COLOR: Chooses 8- or 16-color display. BKGD COLOR: Chooses color of background, text and menu. Three choices are available and these are shown in the table below. BKGD COLOR Background Text Menu 1 Black Gray Dark-blue 2 Dark-blue White Medium blue 3 White Black Gray BEARING READOUT: Chooses how to display bearing of markers (cursor, event marker, bearing marker), in Relative or True bearing. True bearing requires heading data. 5-3 5.3 Short-cut Menu, Preset Menu These menus program the CUSTOM MODE keys [1], [2] and [3], and one of the menus appears according to the setting of CUSTOM KEY on the SYSTEM SETTING 1 menu. Short-cut key: One-touch activation of corresponding dialog box. This is the default setting. Preset key: One-touch setup of mode, sector, train, range, tilt and speed controls. Below are the default settings for PRESET. CUSTOM MODE key Display Mode Sector Train Range (m)* Tilt Speed Key 1 Expanded Horizontal 240° 0° 250 30° Fast Key 2 Horizontal 360° 0° 250 30° Fast Key 3 Vertical Fan 180° 90° 120 90° Fast * - Default range for 60 kHz transducer. Default range changes with transducer. 5.3.1 Selecting short-cut or preset 1. Press the [MENU] key to open the menu. 2. Press to select MENU, and then press MENU COM1 COM2 : SELECT HORZ VERT YES GO TO SYS MENU to select SYS. : CHANGE ES PRESET NO MENU: END Figure 5-2 Display for opening system menu 3. Press to select GO TO SYS MENU. 4. Press to select YES. 5-4 SYS ** SYSTEM MENU ** SYSTEM SETTING: RANGE-SONAR MODE RANGE-VERTICAL MODE RANGE-E/S MODE RANGE-TRACK MODE COLOR PALETTE LANGUAGE SYSTEM BACKUP LOAD BACKUP DATA HEADING OFFSET, DRAFT OFFSET ADJ MOTION SENSOR TX FREQ ADJUST TEST TEST PATTERN DEMO MODE DEFAULT : SELECT : MENU DISPLAY MENU: END Figure 5-3 System menu 5. Press to open the SYSTEM SETTING menu. ** SYSTEM SETTING 1 ** MENU 1 : SHIP'S L/L SHIP'S LOP CURSOR L/L : OFF ON POSITION TRACK CURRENT DATA : OFF HEADING INDICATION : TRUE NORTH MARK : OFF CSE DATA : NAV NAV DATA : GPS TVG CORRECTION : OFF UNIT FLOW FROM ON GYRO LoranC LoranA DR DECCA OTHERS 1/2 1/1 ft °C OFF PRESET KEY OFF °F TEMP TARGET L/L CUSTOM KEY EMPHASIS MODE ETA MARK : OFF : CHANGE FLOW TO AZ m : : : : : : SELECT 2 fa HIRO P/B ON SHORT-CUT KEY NORMAL RED 10sec 30sec 1min 3min 6min MENU: END Figure 5-4 System setting 1 menu 6. Press or to select CUSTOM KEY. 5-5 7. Press or to select PRESET KEY or SHORT-CUT KEY as desired. 8. Press the [MENU] key twice to register your selection and close the menu. 5.3.2 Preset key 1. Select PRESET KEY following the procedure in paragraph 5.2.1 on page 5-3. 2. Press the [MENU] key to open the menu. 3. Press to select MENU, and then press COM1 MENU MODE COM2 SECTOR or to select PRESET. HORZ VERT TRAIN ES RANGE PRESET SYS TILT SPEED PRESENT 360° 0° 160 30° NORM CUSTOM1 240° 0° 160 30° FAST CUSTOM2 360° 0° 160 30° FAST CUSTOM3 180° 90° 120 90° FAST ADJUST THE KNOBS AND FUNCTION KEYS TO THE DESIRED SETTING, THEN PRESS A CUSTOM MODE KEY TO SAVE THE SETTING. FUNCTION KEY: ENTRY MENU: END Figure 5-5 PRESET menu 4. Set the [MODE], [SECTOR], [TRAIN], [RANGE], [TILT] and [FAST SCAN] controls according to target fish or fishing area. 5. Press the CUSTOM MODE keys [1], [2] or [3] to program. You are asked if you want to save the settings to the custom key pressed. (In the example, the custom key [1] was pressed.) SAVE THE SETTING TO CUSTOM1 KEY? NO : CHANGE 6. Press YES MENU: END to select YES. 7. Press the [MENU] key. The message “PRGM SET” appears at the screen top. 8. Press the [MENU] key to finish. Activating custom mode 1. Press appropriate CUSTOM MODE key. The indication CUSTOM1, CUSTOM2 or CUSTOM3 appears at the top of the screen depending on key pressed. 2. To escape from the custom mode operation, operate any of the controls among [MODE], [SECTOR], [TRAIN], [RANGE], [TILT] and [FAST SCAN]. 5-6 5.3.3 Short-cut key The default settings are key [1], interference rejector; key [2], signal level, and key [3], background color. The operator may change their functions as desired. Note: In the combination modes the short-cut key operation is only possible from the main window. 1. Select SHORT-CUT following the procedure in paragraph 5.2.1 on page 5-3. 2. Press the [MENU] key to open the menu. 3. Press to select MENU, and then press COM1 MENU KEY 1 KEY 2 KEY 3 COM2 or to select SHORT-CUT. HORZ VERT ES SHORT-CUT SYS VER SEARCH VOLUME DEL TRACK AUTO TILT SIG LEVEL CLUTTER RES. COLOR WHITE MARKER VER SEARCH VOLUME DEL TRACK SIG LEVEL CLUTTER RES. COLOR WHITE MARKER VER SEARCH VOLUME DEL TRACK SIG LEVEL CLUTTER RES. COLOR WHITE MARKER AUTO TILT AUTO TILT BKGD BKGD BKGD SELECT FUNCTION TO BE ALLOCATED TO EACH CUSTOM KEY. CUSTOM KEY MAY BE USED AS A PRESET KEY. : CHANGE : SELECT MENU: END Figure 5-6 SHORT-CUT menu 4. Press or to select key to preset. For example select KEY 1. 5. Press or to select item. 6. Press the [MENU] key to finish. Activating a short-cut key 1. Press a CUSTOM MODE key, and the dialog box programmed for the custom key pressed appears. The dialog box below is for CLUTTER (HORZ). CLUTTER (HORZ): 2. Press or 0 1 2 3 to select option desired 3. Press the [MENU] key to close the dialog box. 5-7 VERTICAL SEARCH FUNCTION When you find a target of interest on the horizontal display, simply press the function key programmed for VER. SEARCH to get a cross-sectional view of the vertical plane. This mode is useful for evaluating fish school concentration and location of the targeted fish school or for navigation purposes. Fish School The vertical search picture is drawn using the following specifications: - Horizontal range: - Vertical range: - Train marker: - Vertical scan display range: 5-8 Same as set on horizontal mode Same as set on horizontal mode Train angle at the moment function key is turned on 0-90 degrees (own ship position shifted leftward) 5.4 SYS Menu This menu provides items which may be set according to operator’s preference. A demonstration mode is provided to acquaint you with the many functions of this equipment, and it may be used without connection of the transducer. 5.4.1 Displaying the SYSTEM menu 1. Press the [MENU] key to open the menu. 2. Press to select MENU, and then press 3. Press to select GO TO SYS MENU. 4. Press to select YES. to select SYS. ** SYSTEM MENU ** SYSTEM SETTING: RANGE-SONAR MODE RANGE-VERTICAL MODE RANGE-E/S MODE RANGE-TRACK MODE COLOR PALETTE LANGUAGE SYSTEM BACKUP LOAD BACKUP DATA HEADING OFFSET, DRAFT OFFSET ADJ MOTION SENSOR TX FREQ ADJUST TEST TEST PATTERN DEMO MODE DEFAULT : SELECT : MENU DISPLAY Adjusted at installation. See installation manual See Chapter 6. MENU: END Figure 5-7 System menu 5. Press or to select item desired. 6. Press or to open corresponding dialog box. 7. Press or to select option. 8. Press the [MENU] key twice to register your selection and close the menu. 5-9 SYSTEM SETTING 1 menu 1. Display the SYSTEM menu and press 2. Press or to select SYSTEM SETTING. . 3. Press to MENU. 4. Press to select “1.” ** SYSTEM SETTING 1 ** MENU 1 2 POSITION TRACK : SHIP'S L/L SHIP'S LOP CURSOR L/L : OFF ON CURRENT DATA HEADING INDICATION NORTH MARK CSE DATA NAV DATA TVG CORRECTION : : : : : : UNIT TEMP TARGET L/L CUSTOM KEY EMPHASIS MODE : : : : : ETA MARK : OFF : SELECT OFF FLOW FROM TRUE OFF NAV GPS OFF AZ ON GYRO LoranC LoranA DR DECCA OTHERS 1/2 1/1 m ft °C °F FLOW TO fa HIRO P/B OFF ON PRESET KEY SHORT-CUT KEY OFF NORMAL RED : CHANGE 10sec 30sec 1min 3min 6min MENU: END Figure 5-8 System setting 1 menu SYSTEM SETTING 1 menu description POSITION: Chooses how to displays ship’s position; latitude and longitude, Decca/Loran LOP or Cursor L/L. (The connected navigator must be capable of displaying L/L or LOP.) The default setting is latitude and longitude. Position data required. TRACK: Turns the track display on or off on the horizontal display. The track is always shown on the video plotter display regardless of this setting. CURRENT DATA: Turns current data (tide) on or off. FLOW FROM shows from what direction the current is flowing; FLOW TO shows the direction the current is heading. The default setting is OFF. Requires connection of a current indicator. Current Vector FLOW FROM FLOW TO Figure 5-9 Current vector 5-10 HEADING INDICATION: Selects heading indication format, true (default setting) or azimuth, for the echo sounder and vertical fan modes. The default setting is TRUE. Requires heading data. NORTH MARK: Turns the north marker on or off (default setting). Requires heading data. When turned on, the bearing scale shows bearings in cardinal points (N, S, E, W) and half-cardinal points (NE, NW, SE, SW). CSE DATA: Selects heading data source, navigator or gyrocompass, to draw ship’s track. The default setting is navigator. For heading sensor or gyrocompass connection, choose gyrocompass. NAV DATA: Selects source of position data, GPS, Loran C, Loran A, DR (Dead Reckoning), Decca or Others (for equipment not shown, receives talker only). Default setting is GPS. TVG CORRECTION: Changes TVG curve to compensate for attenuation absorption of ultrasonic wave in water. OFF (default setting), standard TVG curve; 1/2, 1/2 of the theoretical absorption value added to TVG curve, and 1/1, full theoretical absorption value added to TVG curve. UNIT: Selects unit of depth measurement: meters (default setting), feet, fathoms, passi/braza, Hiro. TEMP: Selects unit of water temperature measurement: °C (default setting), °F. TARGET L/L: Turn on to output event marker position to external equipment. Requires heading and latitude and longitude data from external equipment. Default setting is OFF. CUSTOM KEY: Selects function of custom mode keys: preset (default setting) or short-cut. For details see paragraph 5.2 on page 5.3. EMPHASIS MODE: Turn on to stretch strongest strength echo in range direction. Default setting is OFF. ETA MARK: A vector line extends from the own ship marker in direction of ship’s bow on the horizontal mode display. The tip of the line shows the estimated time of arrival after the selected ETA time elapses, using the current ship’s speed. ETA is calculated every second considering tilt and detection range. This function requires speed input. ETA marker Figure 5-10 ETA marker 5-11 SYSTEM SETTING 2 menu description ** SYSTEM SETTING 2 ** 1 MENU 2 : OFF : OFF ON SPEED ALARM/MESSAGE : OFF ON SWEEP INDICATOR : DOT SOUNDOME SERIAL NO : -999 DEFAULT SETTING : NO LINE 1000YES STABILIZER AUTO RETRACTION (OFF, 5-15kt) MAXIMUM ALLOWABLE SPEED IS 15 KNOTS WHILE SOUNDDOME IS BEING RETRACTED. IF VESSEL HAS RAPID ACCELERATION CAPABILITIES, AUTO RETRACTION SETTINGS OF 10-12 KNOTS ARE MANDATORY TO AVOID CATASTROPHIC DAMAGE TO SOUNDOME ASSY. ANY PHYSICAL DAMAGE TO THE SOUNDOME ASSY. IS CONSIDERED ABUSE AND IS NOT A WARRANTY ISSUE. : SELECT : CHANGE MENU: END Figure 5-11 System setting 2 menu STABILIZER: Choose ON to compensate for effects of ship’s pitching and rolling. Requires Motion Sensor MS-100 or Clinometer BS-704. AUTO RETRACTION: Turn on to automatically retract the transducer when ship’s speed exceeds the speed set here. The ship’s speed range for automatic retraction is from 5 to 15 knots. The default setting is OFF (no automatic retraction). Requires speed input. Note: The transducer may be retracted at a speed other than the intended one when ship’s speed data is erroneous. 5-12 SPEED ALARM MESSAGE: Turn on (default setting) to display speed alarm message and sound the audio alarm when ship’s speed exceeds allowable speed for a given transducer operation. The audio alarm can be silenced with the [R/B] key. [↓] pressed to lower transducer Speed above 15 kts Message 1 appears. Reduce speed below 15 kts to restore normal operation. Transducer being lowered Speed over 15 kts Message 1 appears and lowering continues. Transducer lowered Speed above 20 kts Message 2 appears accompanied with the aural alarm. Reduce the speed below 20 kts to restore normal operation. [↑] pressed to raise transducer Speed above 15 kts Message 1 appears accompanied with the aural alarm. Transducer is not raised. Reduce the speed below 15 kts to erase the message and restore normal operation. Then, press [↑] again to raise the transducer. Transducer being raised Speed above 15 kts SHIPS SPEED EXCEEDS 15 kt. (SLOW DOWN UNDER 15 kt WHEN MOVING TRANSDUCER UNIT.) PRESS R/B KEY TO SILENCE ALARM. Message 1 Message 1 appears and raising continues. Reduce the speed below 15 kts to erase the message and restore normal operation. TRANSDUCER REMAINS LOWERED. (REDUCE SHIP'S SPEED AND PRESS ↑ TO RETRACT IT.) PRESS R/B KEY TO SILENCE ALARM. Message 2 SWEEP INDICATOR: Shows train position in the horizontal mode and tilt angle in the vertical fan mode, with a line or a dot. (See the illustration on page 2-2 and 3-2.) SOUNDOME SER. NO.: Set according to serial no. of soundome. Note that the setting is not cleared when default settings are restored. 5-13 DEFAULT SETTING: Select YES and press the [MENU] key to restore all default system menu settings. Several beeps sound while default settings are being restored and then normal operation is restored. ** FACTORY SETTING ** ARE YOU SURE? : NO YES NOTE: ALL THE SYSTEM SETTING WILL BE CHANGED TO FACTORY SETTING. : CHANGE MENU: END Figure 5-12 FACTORY SETTING menu 5-14 5.4.2 Sonar (horizontal) mode range settings The user may preset horizontal mode ranges as desired. 1. Select RANGE-SONAR MODE at the SYS menu and then press . ** RANGE-SONAR MODE ** 1 2 3 4 : : : : 5 6 7 8 9 : : : : : 80 120 160 200 250 10 11 12 : : : 300 400 500 13 14 15 TRACK DISP : : : : 10 (10-1600m) 20 40 60 600 800 1000 500 (500-5000m) DEFAULT SETTING : : SELECT NO : CHANGE YES MENU: END Figure 5-13 Range-sonar mode menu 2. Press or to select range number desired. 3. Press or to set range. The setting range depends on the transducer used. The figure above shows the default settings for the 60 kHz transducer. 4. To set the range of the video plotter display, press or . with to select TRACK DISP and set range 5. To restore default horizontal mode range settings, select DEFAULT SETTING, press select YES and press the [MENU] key. to 6. Press the [MENU] key to register settings and close the menu. 5-15 5.4.3 Vertical fan mode range settings As with the horizontal mode, the user may preset the vertical fan mode’s ranges. 1. Select RANGE-VER MODE at the SYS menu and then press . ** RANGE-VER MODE ** 1 2 3 4 : : : : 10 (10-600m) 20 30 40 5 6 7 8 9 : : : : : 60 80 100 120 160 10 11 12 13 14 15 : : : : : : 200 250 300 400 500 600 DEFAULT SETTING : : SELECT NO : CHANGE YES MENU: END Figure 5-14 Range-ver mode menu 2. Press or to select range number desired. 3. Press or to set range. 4. To restore default vertical fan mode range settings, select DEFAULT SETTING, press select YES and press the [MENU] key. 5. Press the [MENU] key to register settings and close the menu. 5-16 to 5.4.4 Echo sounder mode range settings As with the horizontal and vertical fan modes, the user may preset the echo sounder mode’s ranges. 1. Select RANGE-E/S MODE at the SYS menu and then press . ** RANGE-E/S MODE ** 1 2 3 4 : : : : 10 (10-600m) 20 30 40 5 6 7 8 9 : : : : : 60 80 100 120 160 10 11 12 13 14 15 : : : : : : 200 250 300 400 500 600 DEFAULT SETTING : : SELECT NO : CHANGE YES MENU: END Figure 5-15 Range-E/S mode menu 2. Press or to select range number desired. 3. Press or to set range. The setting range depends on the transducer used. 4. To restore default echo sounder mode range settings, select DEFAULT SETTING, press to select YES and press the [MENU] key. 5. Press the [MENU] key to register settings and close the menu. 5-17 5.4.5 Track range settings You may choose the video plotter display scale range as follows. 1. Choose RANGE-TRACK at the SYS menu and then press ►. ** RANGE-TRACK MODE ** 1 2 3 : : : 500 (100-10000m) 1000 2000 4 : 4000 5 : 8000 DEFAULT SETTING : : SELECT NO YES : CHANGE MENU: END Figure 5-16 Range-track mode menu 2. Press ▲ or ▼ to choose range number desired. 3. Press ◄ or ► to set. 4. Press the [MENU] key to register settings and close the menu. 5-18 5.4.6 Color palette The color palette lets the user change the color of echoes, background, text and menu as desired. Cursor ** COLOR PALETTE ** 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ECHO Arrow BKGD TEXT MENU BKGD TEXT MENU BKGD2 BKGD1 BKGD TEXT MENU BKGD3 COLOR : ECHO 1 R G B : : : DEFAULT SETTING : 3 6 13 NO : SELECT YES (ECHO & BKGD COLORS WILL BE CHANGED.) : CHANGE MENU: END Figure 5-17 Color palette 1. Press or to place the cursor and arrow on the item to change. Pressing arrow and cursor from left to right and top to bottom. 2. Press or to select R(red), G(green) or B(blue) as appropriate. 3. Press or to adjust color. shifts the 4. Press the [MENU] key to register your settings and close the menu. Note: To restore default color settings, select DEFAULT SETTING, press to select YES, and press the [MENU] key. A few beeps sound while the default colors are being restored and then normal operation is restored. 5-19 5.4.7 Language Menu language can selected from among the languages shown in the Language menu and the default language is English. ** LANGUAGE ** LANGUAGE: JAPANESE ITALIANO SVENSK : CHANGE MENU: END ENGLISH PORTUGUES THAI FRANCAIS DANSK CHINESE Figure 5-18 Language menu 5.4.8 System backup User settings can be backed up with the menu item SYSTEM BACKUP. ** SYSTEM BACKUP ** ARE YOU SURE? : NO YES NOTE: OVERWRITE PREVIOUS BACKUP DATA. : CHANGE MENU: END Figure 5-19 System backup menu 5.4.9 Loading backup data System data may be loaded from the LOAD BACKUP DATA menu. ** LOAD BACKUP DATA ** ARE YOU SURE? : NO YES NOTE: OVERWRITE CURRENT SETTINGS. : CHANGE MENU: END Figure 5-20 Load backup data menu 5-20 ESPANOL NORSK VIETNAM 5.4.10 Transducer frequency adjustment If the CH-250 is receiving interference from a video sounder or other sonar on board your ship, adjust the frequency of the CH-250’s transducer to reduce the interference. ** TX FREQ ADJUST ** FREQ SHIFT : : CHANGE 60.0 kHz (57-63 kHz) MENU: END Figure 5-21 TX frequency adjustment menu 5.4.11 Demonstration mode The demonstration mode provides a simulated sonar picture which helps you become acquainted with how your sonar works. Connection of the transducer is not required. All controls are operational. 1. Display the SYS menu. 2. Select DEMO MODE. 3. Press to open the menu. ** DEMO MODE ** DEMO MODE : CHANGE : OFF ON MENU: END Figure 5-22 Demo mode menu 4. Select OFF or ON as appropriate and press the [MENU] key. (DEMO) appears at the top of the screen when the demonstration mode is active. 5-21 5.4.12 Restoring all default settings The item DEFAULT lets you restore all default menu settings. Select YES and press the [MENU] key to restore all default settings. Note that settings stored in SYSTEM BACKUP are not disturbed. ** DEFAULT ** ARE YOU SURE? : NO YES NOTE: RESET ALL THE SETTINGS INCLUDED IN SYSTEM MENU TO DEFAULT. : CHANGE MENU: END Figure 5-23 Default menu CAUTION All default settings will be restored. If necessary jot down settings which must be restored. 5-22 6. MAINTENANCE, TROUBLESHOOTING This chapter provides information necessary for keeping the equipment in good working order. WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. 6.1 Preventive Maintenance Check the following points monthly. • Check all cables. If damaged, replace. • Check connectors at rear of each unit. Clean if necessary. • Check earth of each unit. Clean if necessary. • Check voltage of ship’s mains to be sure it is within the equipment’s power rating. 6.2 Cleaning the Equipment Dust or dirt can be removed from the equipment with a soft, dry cloth. Do not use chemical cleaners to clean the equipment – they can remove paint and markings. Wipe the LCD carefully to prevent scratching, using tissue paper and an LCD cleaner. To remove stubborn dirt, use an LCD cleaner, wiping slowly with tissue paper so as to dissolve the dirt. Change paper frequently so the dirt will not scratch the LCD. 6-1 6.3 Hull Unit Maintenance 6.3.1 Lubrication Grease the raise/lower screw shaft once a year. Also, grease the raise/lower main shaft (upper part of the grease cotton retainer) twice a year. These parts can be accessed by removing the raise/lower drive assembly cover. 6.3.2 Manually raising, lowering transducer WARNING Turn off the power at the ship's mains switchboard before conducting the procedure below. Rotating motor can cause bodily injury. 1. Turn off the breaker on the hull unit. 2. Set 19 mm ratchet wrench to nut and turn. 3. Check that the transducer raises and lowers smoothly, from the upper to the lower limit positions. If the transducer cannot be raised smoothly, do not use excessive force; the shaft may bend, causing damage to other components. 4. Check soundome and tank. Remove marine life with fine sandpaper or piece of wood. Attach ratchet wrench here. Figure 6-1 Hull unit 6-2 6.4 Transducer Maintenance When the ship is dry-docked remove marine growth from the transducer with fine sandpaper or a piece of wood. CAUTION Do not paint the transducer face. Loss of sensitivity will result. Do not use plastic solvents to clean the transducer. They can damage the transducer. 6.5 Fuse Replacement The fuse in the hull and transceiver units protect them from overvoltage, equipment fault and reverse polarity of the ship’s mains. If the power cannot be applied first check the power cable between the transceiver unit and the display unit. If the power still cannot be applied, the fuse in the transceiver unit may have blown. Have a suitably qualified technician check the fuse. CAUTION Use the proper fuse. Use of a wrong fuse can cause fire or equipment damage. 6-3 6.6 Troubleshooting The table below provides common symptoms of equipment troubles and the means to rectify them. Symptom Cannot turn on the power. Bottom echo becomes irregular. Weak echo Check, Remedy • • • • • Check cable between transceiver unit and display unit. Check ship’s mains. Have a suitably qualified technician check the fuse in the transceiver unit. Rough seas. Distance to the bottom changes due to rolling and pitching. Long range selected. Transmission period is longer so ship’s pitching and rolling are apt to affect detection of echo. • Output power set to minimum. Set to maximum, on the COM1 menu. • Excessive TVG. Readjust TVG on the appropriate menu (HORZ, VERT, ES). Note that readjustment of TVG is necessary when gain is adjusted. Somewhat strange color Picture contains noise. • [BRILL] key setting too low. Increase brightness with [BRILL] key. • Equipment not grounded properly. Check equipment ground. • Power cable is too close to the signal cable. Relocate power cable or signal cable. • Debris may be on sea surface. Reject unwanted noise with the interference rejector on the COM1 menu. Picture does not change when tilt angle is changed. (Bottom is not displayed in vertical fan picture when bottom is flat.) 6-4 • Problem in tilt mechanism or control line. Contact a FURUNO agent or dealer for advice. 6.7 Error Messages The table below shows the error messages which may appear on the display. All error messages are accompanied by an audio alarm, which you may silence with the [R/B] key. Message Meaning, Remedy Hull Unit HULL UNIT POWER OFF (CHECK BREAKER AND FUSE.) PRESS R/B KEY TO SILENCE ALARM. Hull unit is not powered. Silence the audio alarm with the [R/B] key, and then turn on the hull unit to erase the message and restore normal operation. RAISE/LOWER FUNCTION HAS NOT BEEN COMPLETED. CHECK IF THE BREAKER AT THE HULL UNIT HAS BEEN ACTIVATED. MAXIMUM ALLOWABLE SPEED IS 15 KNOTS WHILE SOUNDOME IS BEING RETRACTED. PRESS R/B KEY TO SILENCE ALARM. You attempted to raise or lower the transducer when the ship’s speed is above 15 knots or the breaker on the hull unit tripped. Check the breaker and lower the ship’s speed below 15 knots to execute function desired. Frequency Code Error FREQUENCY CODE ERROR (CHECK TRANSCEIVER UNIT.) PRESS R/B KEY TO SILENCE ALARM. CPU does not receive frequency flag from transducer. Silence the audio alarm with the [R/B] key, and then check the transceiver unit. Train Error TRAIN NG CPU does not receive heading signal. Check source of heading signal. Excessive Speed SHIPS SPEED EXCEEDS 15 kt. (SLOW DOWN UNDER 15 kt WHEN MOVING TRANSDUCER.) PRESS R/B KEY TO SILENCE ALARM. See page 5-11 for details. TRANSDUCER REMAINS LOWERED. (REDUCE SHIP'S SPEED AND PRESS ↑ TO RETRACT IT.) PRESS R/B KEY TO SILENCE ALARM. 6-5 6.8 Diagnostics 1. Press the [MENU] key to open the menu. 2. Press to select MENU, and then press 3. Press to select GO TO SYS MENU. 4. Press to select YES. to select SYS. 5. Select TEST and press to start the test. The lamps above the XDR switches light alternately for one second while the test is being conducted. In a few moments the results of the test appear. MAIN PROGRAM NO. 0650110-0** PANEL PROGRAM NO. 0650104-0** ROM : OK RAM : OK VRAM : OK NMEA : OK* PANEL CPU : OK TX FREQUENCY : 60 kHz† ROLL : 10 PITCH : 10 PULSES NG 357 0 TRAIN TEST COUNT= : 0 REMOTE CONTROL PANEL 0-127 (LED) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 EXIT 0 0 0 * = Requires special plug to test. Nothing displayed when plug is not connected. ** = Program Version No. † = Frequency depends on transducer used. Figure 6-2 Test results Interpreting the test results display • The program numbers of the MAIN and PANEL programs appear at the top of the display. • The ROM, RAM, VRM, NMEA and PANEL CPU are checked for proper operation and the results displayed as OK or NG (No Good). For NG contact a FURUNO agent or dealer for advice. • The TX FREQUENCY of the transducer is measured and displayed. 6-6 • TRAIN shows a figure between 355-359 if normal. NG appears in case of train error. • TEST COUNT shows the number of times the test has been consecutively executed. • At the bottom of the screen there are two major groups of zeroes (0), and they represent the keys and controls on the control panel and remote controller. Press a key and its on-screen location shows “1” while the key is pressed and “0” when it is released. Operate a control and its on-screen location changes as below. When the [GAIN] control is operated the panel dimmer increases or decreases with adjustment of the control. GAIN control: Shows 0-127. Other controls: Shows 0-19. To quit the test, press the [MENU] key three times. 6-7 6.9 Test Pattern A test pattern can be displayed to check for proper display of colors. 1. Press the [MENU] key to open the menu. 2. Press to select MENU, and then press 3. Press to select GO TO SYS MENU. 4. Press to select YES. to select SYS. 5. Select TEST PATTERN and press to display the test pattern. Press again to change the test pattern. The pattern changes in the sequence shown below with each press of . 16 tones of RED 16 tones of GREEN 16 tones of BLUE WHITE RED BLACK BLUE Figure 6-3 Test pattern To quit the test pattern, press the [MENU] key three times. 6-8 GREEN MENU TREE [MENU] key COM1 menu TX POWER (MAX, MIN) PULSELENGTH (LONG, SHORT) TX RATE (EXTERNAL, 1-10; 10) INT REJECT (OFF, ON) DEFAULT SETTINGS AGC (OFF, ON) SHOWN IN BOLD ITALIC. AUDIO LEVEL (0-10) COM2 menu DELETING TRACK (NO, YES) WHITE MARKER (8-color: OFF, 1-7; 16-color: OFF, 1-15) SIG LEVEL (8-color: OFF, 1-6; 16-color: OFF, 1-14) COLOR (16, 8) BKGD COLOR (1, 2, 3) BEARING READOUT (RELATIVE, TRUE) HORZ menu TVG LEVEL (0-10, 4.0) TVG DISTANCE (0-10, 4.0) GAIN ADJUST (-10 - +10, 0) RES. COLOR (LOG, LINEAR, SQUARE, CUBE) CLUTTER (0, 1, 2, 3) TARGET KEY (REVERSE, POS, ECHO) LOCK MODE (AUTO, MANUAL) AUTO TILT (OFF, ±2°, ±4°, ±6°, ±10°) VERT menu TVG LEVEL (0-10, 4.0) TVG DISTANCE (0-10, 4.0) GAIN ADJUST (-10 - +10, 0) RES. COLOR (LOG, LINEAR, SQUARE, CUBE) CLUTTER (0, 1, 2, 3) HORZ RANGE (x1, x2) ES menu TVG LEVEL (0-10, 4.0) TVG DISTANCE (0-10, 4.0) GAIN ADJUST (-10 - +10, 0) RES. COLOR (LOG, LINEAR, SQUARE, CUBE) CLUTTER (0, 1, 2, 3) A-SCOPE (OFF, ON) (When SHORT-CUT KEY is selected at SYSTEM SETTING 1 menu.) SHORT-CUT menu KEY1 (VER SEARCH, VOLUME, DEL TRACK, AUTO TILT, BKGD SIG LEVEL, CLUTTER, RES. COLOR, WHITE MARKER) KEY2 (Same choices as KEY1. Default setting: VOLUME) KEY3 (Same choices as KEY1. Default setting: DEL TRACK) PRESET menu (Default setting) CUSTOM1 (MODE: HORIZONTAL EXPANSION, SECTOR: 240°, TRAIN: 0°, RANGE (m): 200, TILT: 30°, SPEED: FAST ) CUSTOM2 (MODE: HORIZONTAL, SECTOR: 360° , TRAIN: 0°, RANGE (m): 2000, TILT: 30°, SPEED: FAST ) CUSTOM3 (MODE: VERTICAL, SECTOR: 180°, TRAIN: 90°, RANGE (m): 120, TILT: 90°, SPEED: FAST ) (CONTINUED ON NEXT PAGE) M-1 (CONTINUED FROM PREVIOUS PAGE) SYSTEM menu SYSTEM SETTING SYSTEM SETTING 1 POSITION (SHIP'S L/L, SHIP'S LOP, CURSOR L/L) TRACK (OFF, ON) CURRENT DATA (OFF, FLOW FROM, FLOW TO) HEADING INDICATION (TRUE, AZ) NORTH MARK (OFF, ON) CSE DATA (NAV, GYRO) NAV DATA (GPS, LoranC, LoranA, DR, DECCA, OTHERS) TVG CORRECTION (OFF, 1/2, 1/1) UNIT (m, ft, fa, HIRO, P/B) TEMP (°C, °F) TARGET L/L (OFF, ON) CUSTOM KEY (PRESET KEY, SHORT-CUT KEY) EMPHASIS MODE (OFF, NORMAL, RED) ETA MARK (OFF, 10sec, 30sec, 1min, 3min, 6min) SYSTEM SETTING 2 STABILIZER (OFF, ON) AUTO RETRACTION (OFF, 5-15kt) SPEED ALARM/MESSAGE (OFF, 15kt, 20kt) SWEEP INDICATOR (DOT, LINE) SOUNDOME SERIAL NO. (-999, 1000-) DEFAULT SETTING (NO, YES) RANGE-SONAR MODE (all default ranges) 60 kHz (min. range: m, 10: ft, 40; fa, p/b, hiro, 5. max. range: m , 1600; ft, 5000, fa, 800; P/B, Hiro, 1000) 88 KHz (min. range: m, 10: ft, 40 ; fa, P/B, Hiro, 5; max. range: m, 1200; ft, 4000; fa, 700; P/B, Hiro, 800) 150 KHz (min. range: m, 10: ft, 40 ; fa, P/B, Hiro, 5; max. range: m, 1000; ft, 3500; fa, 700; P/B, Hiro, 700) 180 KHz (min. range: m, 10: ft, 40 ; fa, P/B, Hiro, 5; max. range: m, 800; ft, 2500; fa, 500; P/B, 600, Hiro, 700) 240 KHz (min. range: m, 10: ft, 30 ; fa, P/B, Hiro, 5; max. range: m, 600; ft, 2000; fa, P/B, Hiro, 400) RANGE-VER MODE (all default ranges) m: 10, 20, 30, 40, 60, 80, 100, 120, 160, 200, 250, 300, 400, 500, 600 ft: 30, 60, 90, 120, 150, 200, 250, 300, 400, 500, 600, 800, 1000, 1500, 2000 fa, P/B, Hiro: 10, 20, 30, 40, 50, 60, 80, 100, 120, 140, 160, 200, 250, 300, 400 RANGE-E/S MODE (all default ranges) m: 10, 20, 30, 40, 60, 80, 100, 120, 160, 200, 250, 300, 400, 500, 600 ft: 30, 60, 90, 120, 150, 200, 250, 300, 400, 500, 600, 800, 1000, 1500, 2000 fa, P/B, Hiro: 10, 20, 30, 40, 50, 60, 80, 100, 120, 140, 160, 200, 250, 300, 400 RANGE-TRACK MODE (all default ranges) m: 500, 1000, 2000, 4000, 8000 ft: 1000, 2000, 5000, 10,000, 20,000 fa, P/B, Hiro: 200, 500, 1000, 2000, 4000 COLOR PALETTE (Adjusts color of echoes, text and background.) LANGUAGE (JAPANESE, ENGLISH, FRANCAIS, ESPANOL, ITALIANO, PORTUGUES DANSK, NORSK, SVENSK, THAI, CHINESE, VIETNAM) SYSTEM BACKUP (NO, YES) LOAD BACKUP DATA (NO, YES) HEADING OFFSET. DRAFT OFFSET (-180°, +180°, 0; 0 - 60 (m), 0) ADJ MOTION SENSOR (ROLL ANGLE: -10° - +10°, 0; PITCH ANGLE: -10° - +10°, 0) TX FREQ ADJUST (171 - 189 kHz, 180 kHz) TEST (Checks equipment for proper operation.) TEST PATTERN (Displays series of test patterns.) DEMO MODE (OFF, ON) DEFAULT (NO, YES) M-2 FURUNO CH-250/250S SPECIFICATIONS OF 10.4 INCH COLOR LCD SEARCHLIGHT SONAR CH-250/250S 1 GENERAL 1.1 Display system 1.2 Transmit frequency CH-250 CH-250S 1.3 Output power 1.4 Range (factory setting) Range 10.4 inch color LCD 60, 88 or 150 kHz selected 180 or 240 kHz selected 0.8 kW (60 kHz) to 1.2 kW (150 kHz) 60 kHz H V Detection Range (m) [H: horizontal mode, V: vertical fan mode] 88 kHz 150 kHz 180 kHz H V H V H V 240 kHz H V 1 10 10 10 10 10 10 10 10 10 10 2 20 20 20 20 20 20 20 20 20 20 3 40 30 40 30 40 30 40 30 30 30 4 80 40 80 40 60 40 60 40 40 40 5 120 60 120 60 80 60 80 60 60 60 6 160 80 160 80 120 80 100 80 80 80 7 200 100 200 100 160 100 120 100 100 100 8 250 120 250 120 200 120 160 120 120 120 9 300 160 300 160 250 160 200 160 160 160 10 400 200 400 200 300 200 250 200 200 200 11 500 250 500 250 400 250 300 250 250 250 12 600 300 600 300 500 300 400 300 300 300 13 800 400 800 400 600 400 500 400 400 400 14 1200 500 1000 500 800 500 600 500 500 500 15 1600 600 1200 600 1000 600 800 600 600 600 2 DISPLAY/ CONTROL UNIT 2.1 Display 10.4 inch color LCD, 640 x 480 dots 2.2 Picture color Echo: 16 or 8 colors (echo) Back-ground: 3 colors selected (user setting available) 2.3 Display mode Horizontal (Normal/Expanded), Vertical fan (Left-right or top-bottom position), Echo sounder 2.4 Combination display Plotter, Vertical fan, Strata, History 2.5 Alphanumerical indication Range, Sensitivity, TVG, Tilt angle, Interference rejection 2.6 Data indication L/L (own ship or cursor), Depth, Bearing, Ship’s speed/Water current vector, Track, Water temperature (external data required) 2.7 Marker Range and bearing to waypoint 2.8 Indication unit Meter, feet, fathom, P/B SP - 1 E1316S01L 110408 FURUNO 2.9 CH-250/250S Audio monitor 2 W output (4 ohms), Freq. 1.0 kHz (external speaker required) 2.10 Event mark 5 points 2.11 Hue Low level enhanced echo disappeared 2.12 Red color enhancement Strong echo indicated as expanded to range direction 2.13 Arrival mark Vector estimated point after 10 seconds to 6 min. (menu setting) 2.14 Target lock (three function selected on menu) Scanning reverse Scanning orientation changed by pressing key Location search Auto-search for marker setting location Echo search Auto-search for signal level in a search zone, or manual search 2.15 Clutter Suppresses low intensity echoes. 3 TRANSCEIVER UNIT 3.1 Frequency 60/88/150/180/240 kHz, Auto-setting according to Hull unit specs. 3.2 Output power 0.8-1.2 kW (due to frequency), power reduction function available 3.3 Output pulse length 0.2 to 20.0 ms, according to range 3.4 TVG Level: 100 dB max. , Distance: 1000 m 4 HULL UNIT 4.1 Transducer travel 4.2 Raise/lower time 30 s at 400 mm travel 4.3 Ship’s bow setting Setting offset on menu at installation within ±30° 4.4 Horizontal mode control 4.5 400 mm or 250 mm Scanning angle 6° to 360°, 24° step Scanning center 6° steps, 360° setting available Scanning step angle Normal: 6°, High speed: 12° Elevation angle +5° to 90°, 1° step Auto tilt setting ±2° to ±10° Time to train full circle 60 kHz: Range (m) Time (sec) 10 20 40 80 120 160 200 250 300 400 500 600 800 1200 1600 Norm 9 9 9 9 10 13 16 20 24 32 40 48 64 97 128 Fast 9 9 9 9 10 12 14 16 18 22 26 30 37 54 70 10 20 40 60 80 120 160 200 250 300 400 500 600 800 1000 Norm 7 7 7 7 7 10 13 16 20 24 32 40 48 64 81 Fast 7 7 7 7 7 9 11 13 15 17 21 25 28 36 45 150 kHz: Range (m) Time (sec) 4.6 Vertical fan mode control Scanning angle 6° to 180°, 12° step Scanning center 0° to 180°, 6° step Scanning step angle Normal: 3°, High speed: 6° Time to train 360°, 6° step SP - 2 E1316S01L 110408 FURUNO 4.7 Transceiver beam width (-6 dB) CH-250/250S Frequency Vertical Horizontal 60 kHz: 20° 17° 88 kHz: 16° 13° 150 kHz: 9° 9° 180 kHz: 9° 9° 240 kHz: 8° 8° 4.8 Allowable ship’s speed 20 kn or less (15 kn during raise/lower operation) 4.9 Stabilizer Within 30°, optional motion sensor or clinometers required 5 5.1 5.2 INTERFACE Data format Input IEC61162-1 (NMEA0183 Ver1.5/2.0) DBS, DBT, DPT, GGA, GLL, HDG, HDM, HDT, MDA, MTW, RMA, RMC, VDR, VHW, VTG 5.3 Output SSTLL 6 POWER SUPPLY 6.1 Display/Control /Transceiver unit 12-32 VDC: 4.7-1.8 A, 58 VA or less 6.2 Hull unit 12/24-32 VDC: 4.7/2.3-1.8 A, 58 VA or less Max. 16.7/8.2-7.7 A, 200-246 VA 6.3 Rectifier (option) 110/220 VAC, 13 A, 1 phase, 50/60 Hz 7 ENVIRONMENTAL CONDITION 7.1 Ambient temperature -15°C to +55°C (Soundome: 0°C to +35°C) 7.2 Relative humidity 95% or less at +40°C 7.3 Degree of protection Display/Control unit IPX5 Transceiver/Hull unit IPX2 8 COATING COLOR 8.1 Display/Control unit 8.2 Transceiver unit N3.0 (panel), 2.5GY5/1.5 (chassis) N3.0 SP - 3 E1316S01L 110408 This page is intentionally left blank. INDEX A AGC .......................................................5-2 A-scope display ......................................4-9 Automatic tilt.........................................2-18 B Background color....................................5-2 Backup data loading ..............................................5-20 saving ...............................................5-20 BRILL control..........................................1-5 C Clutter echosounder mode ........................... 4-11 horizontal mode.................................2-18 vertical fan mode...............................3-13 Color palette .........................................5-19 Colors background .........................................5-3 display.................................................5-3 COM1 menu ...........................................5-1 COM21 menu .........................................5-3 Control description..................................1-1 Course data.......................................... 5-11 Current (tide) data.................................5-10 Cursor data echo sounder mode ............................4-5 horizontal mode...................................2-5 vertical fan mode.................................3-7 Custom key .......................................... 5-11 CUSTOM MODE keys preset function ....................................5-6 selection of function ............................5-4 short-cut function.................................5-7 D Default settings.....................................5-22 Demonstration mode ............................5-21 Depth marker (horizontal mode) .............2-7 Depth marker (vertical fan mode)............3-9 Diagnostics.............................................6-6 Display modes ........................................1-6 EVENT key echo sounder mode.............................4-5 horizontal mode...................................2-6 vertical fan mode .................................3-8 Event marker deleting from echo sounder mode .......4-6 deleting from horizontal mode .............2-7 deleting from vertical fan mode............3-9 inscribing from echo sounder mode.....4-6 inscribing from horizontal mode...........2-6 inscribing from vertical fan mode .........3-8 output on/off ......................................5-11 F FAST SCAN key echo sounder mode.............................4-4 horizontal mode...................................2-5 vertical fan mode .................................3-7 FULL/HALF key horizontal mode...................................2-4 vertical fan mode .................................3-5 Fuse replacement ...................................6-3 G Gain adjustment echo sounder mode...........................4-10 horizontal mode.................................2-17 vertical fan mode ...............................3-12 GAIN control ...........................................1-7 H Heading indication ................................5-11 Horizontal range (vertical fan mode) .....3-13 Horizontal range marker (vertical fan mode)...............................3-9 Horizontal/history display ......................2-25 HORZ menu..........................................2-17 Hull unit maintenance .............................6-2 I Interference rejector..............................3-11 L Language..............................................5-20 E M Emphasis mode.................................... 5-11 Error messages ......................................6-5 ES menu...............................................4-10 ETA marker........................................... 5-11 MAIN/SUB key.............................2-25, 3-16 Maintenance hull unit................................................6-2 preventive............................................6-1 IN-1 replacement of fuse.............................6-3 transducer...........................................6-3 MENU key ..............................................1-7 Menu tree .............................................. M-1 N Navigation data..................................... 5-11 North marker......................................... 5-11 P Position display format..........................5-10 POWER switch .......................................1-3 PRESET menu .......................................5-6 Pulselength.............................................2-9 R R/B key echo sounder mode ............................4-7 horizontal mode...................................2-7 vertical fan mode.................................3-9 Range echo sounder mode ............................4-3 horizontal mode...................................2-3 presetting for echo sounder mode.....5-17 presetting for horizontal mode...........5-15 presetting for vertical fan mode .........5-16 track range preset .............................5-18 vertical fan mode.................................3-3 RANGE control echo sounder mode ............................4-3 horizontal mode...................................2-3 vertical fan mode.................................3-3 Range marker echo sounder mode ............................4-7 Remote controller ...................................1-2 Resolution color echosounder mode ........................... 4-11 horizontal mode.................................2-18 vertical fan mode...............................3-12 S SECTOR control horizontal mode...................................2-4 vertical fan mode.................................3-5 SHORT-CUT menu.................................5-7 Signal level .............................................5-3 Signal level ........................................... 2-11 Speed alarm .........................................5-13 IN-2 Stabilizer ...............................................5-12 Sweep indicator ....................................5-13 SYS menu...............................................5-9 System configuration ............................... vii SYSTEM SETTING 1 menu..................5-10 SYSTEM SETTING 2 menu..................5-12 T Target lock echo mode ........................................2-15 manual position mode .......................2-14 manual reverse mode........................2-13 selection of mode ..............................2-13 Test pattern .............................................6-8 TILT control echo sounder mode.............................4-4 horizontal mode...................................2-5 vertical fan mode .................................3-6 Track deleting................................................5-3 on/off .................................................5-10 range preset ......................................5-18 TRAIN control echo sounder mode.............................4-4 horizontal mode...................................2-5 vertical fan mode .................................3-4 Transducer automatic retraction...........................5-12 maintenance........................................6-3 Transducer (XDR) switches ....................1-3 Transmitter output power ........................2-8 Troubleshooting ......................................6-4 TVG echo sounder mode.............................4-7 horizontal mode...................................2-9 vertical fan mode ...............................3-10 TVG curve.............................................5-11 U Unit of measurement depth .................................................5-11 water temperature .............................5-11 V VERT menu ..........................................3-12 W White marker ..........................................5-3
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Mode : UseOutlines XMP Toolkit : 3.1-701 About : uuid:0fef07fc-28c5-4666-b3aa-b791c994f22f Producer : Acrobat Distiller 4.05 for Windows Create Date : 2003:11:04 10:04:36Z Modify Date : 2011:04:08 13:13:25+09:00 Metadata Date : 2011:04:08 13:13:25+09:00 Document ID : uuid:4ce35383-c2df-4db8-b2c5-1babd46cc882 Instance ID : uuid:4501c2bb-1bbe-4e6e-9a8b-350c57e33b8c Format : application/pdf Has XFA : No Page Count : 118EXIF Metadata provided by EXIF.tools