Furuno Navpilot 700 Installation Instructions
2015-08-11
: Furuno Furuno-Navpilot-700-Installation-Instructions-800170 furuno-navpilot-700-installation-instructions-800170 furuno pdf
Open the PDF directly: View PDF .
Page Count: 6
Download | ![]() |
Open PDF In Browser | View PDF |
FURUNO U.S.A., INC. www.furunousa.com Camas, WA (360) 834-9300 Denton, MD (410) 413-4420 FPS8 Power Steering Module for the NavPilot 700 711 720 Autopilot Installation Information Compatible with the following pump models: PUMPHRP05-12, PUMPHRP05-24, PUMPHRP11-12, PUMPHRP11-24, PUMPHRP17-12, PUMPHRP17-24 1) 2) 3) 4) 5) 6) Table of Contents Cover Pre-Attachment Preparation Attaching the FPS8 to the HRP Pump Hydraulic Diagram – Single Helm and Single Cylinder Hydraulic Diagram – Dual Helm and Dual Cylinder Electrical Connection Diagram FURUNO U.S.A., INC. www.furunousa.com Camas, WA (360) 834-9300 Denton, MD (410) 413-4420 Pre-Attachment Preparation WARNING!!! It is critical that this conversion only be performed on a VERY CLEAN work surface! DIRT, DUST AND/OR OTHER CONTAMINANTS WILL DAMAGE THE PUMP AND CAUSE IT TO FAIL!!! STEP 1 Use either a 19mm or 3/4" wrench to remove the 3 hydraulic fittings from the top of the HRP Pump and discard. Five new fittings are provided with the hardware kit. See compatible pump models listed above STEP 2 Insert the 3 "O" rings from the hardware kit into the round recesses in the bottom of the FPS-8 Power Steering Module. Apply a small amount of hydraulic fluid to the “O” rings to hold them in place. Carefully assemble and tighten allen screws evenly, ensuring that the o-rings are not pinched!! FURUNO U.S.A., INC. www.furunousa.com Camas, WA (360) 834-9300 Denton, MD (410) 413-4420 Attaching the FPS8 to the HRP Pump STEP 3 Align the 3 bolt holes in FPS-8 Power Steering Module with the 3 threaded holes in the HRP Pump housing. Screw in the 3 Allen-head bolts from the hardware pack. Tighten them evenly with a 3/16" Allen wrench. Make sure the "O" rings remain in place and do not fall out or get pinched during assembly. STEP 4 Insert the 5 hydraulic fittings from the hardware pack into the 5 threaded holes in the FPS-8 Power Steering Module. Please see the FPS-8 Installation Manual for more information regarding the hydraulic connections. Connect wires per instructions in the NavPilot 700 Installation Manual Pump / motor wires to TB2 in NavPilot Processor FPS-8 Sensor wires to TB5 in Navpilot Processor FURUNO U.S.A., INC. www.furunousa.com Camas, WA (360) 834-9300 Hydraulic Diagram - Single Helm & Single Ram HELM STARBOARD HELM / TANK RT PO STARBOARD STARBOARD PORT PORT NavPilot HRP Pump with FPS8 Power Steering Module CYLINDER A Denton, MD (410) 413-4420 FURUNO U.S.A., INC. www.furunousa.com Camas, WA (360) 834-9300 Denton, MD (410) 413-4420 Hydraulic Diagram - Dual Helm & Dual Cylinder HELM B UPPER Upper Helm Station must have a vented fill plug. Lower Helm Station must have a non-vented fill plug. HELM A LOWER PORT HE LM / TA N K PORT STARBOARD CYLINDER A STARBOARD CYLINDER B STARBOARD PORT PORT NavPilot HRP Pump with FPS8 Power Steering Module PORT HELM / TANK STARBOARD PORT STA R BO A R D STARBOARD K HELM / TAN FURUNO U.S.A., INC. www.furunousa.com Camas, WA (360) 834-9300 Denton, MD (410) 413-4420 Electrical Connection Diagram NavPilot 700 / 711 / 720 Processor (FAP-7002) TB13 TB2 Motor / Solenoid + - TB1 Power Input + - TB8 TB10 TB3 TB11 TB12 TB4 TB5 TB6 TB7 Each of the sensor cables has the same 3 wires. It does not matter which set of 3 go to pins 1, 2 & 3 or 4, 5 & 6. It only matters that the order of the wires are as follows: To TB5 12 / 24 VDC INPUT Pin 1 = SW1 Brown Pin 2 = SW1 Black Pin 3 = SW1 Blue Pin 4 = SW2 Brown Pin 5 = SW2 Black Pin 6 = SW2 Blue 1 2 3 4 5 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Furuno Create Date : 2011:11:18 19:15:35Z Modify Date : 2011:11:22 10:33:59-08:00 Subject : Has XFA : No Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : Furuno Description : Title : Creator Tool : Microsoft® Office Visio® 2007 Metadata Date : 2011:11:22 10:33:59-08:00 Keywords : Producer : Microsoft® Office Visio® 2007 Document ID : uuid:806290b1-3458-44dc-91dc-5553a95a6643 Instance ID : uuid:32facbad-69fa-466a-b58f-e77c9f32002d Page Count : 6EXIF Metadata provided by EXIF.tools