Futaba FMR-03-24G Radio Control User Manual 2

Futaba Corporation Radio Control 2

UserManual.wiki >

FMR-03-24G User Manual >

Contents

1. User Manual 1
2. User Manual 2
3. User Manual 3

User Manual 2

69<Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.TELEMETRY Displaying data from the receiver This screen displays your choice of data from the receiver.Also warnings can be activated regarding other data from your aircraft. For example, if the receiver voltage drops, the user can be warned by an alarm (and vibration).*Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions. ● Select [TELEMETRY] in the Linkage menu and access the setup screen shown below by pushing the RTN button.● Push S1 button to advance to next page.How to see telemetry data1. Telemetry screen can be called select [TELEMETRY] in the Linkage menu and access the setup screen by pushing the RTN button. 2. If each item is chosen and the RTN button is pushed, an alarm setup can be performed with the minimum/maximum after a transmitter is turned on. *Receiver voltage can be checked immediately. An optional sensor will need to be attached to S.BUS2 of a receiver if you would like to see other information. *No special setup is necessary if each sensor displayed is left as in the default setup. Separate sensor ID is also unnecessary. However, if two or more of one kind of sensor is used, setup is required in the "SENSOR" menu.WARNING Do not watch the transmitter screen during ight.*You may loose sight of the aircraft during ight and this is extremely dangerous. Have an assistant on hand to check the screen for you. A pilot should NEVER take his eyes off his aircraft.Scrolling● Moving cursor● Receiver → Transmitter. The reception strength is shown.● Push the S1 button to call next page.

70 <Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.TELEMETRY : RECEIVER [BATTERY] Displaying data from the receiver battery voltageIn this screen, the battery voltage of a receiver is displayed.If it becomes higher or lower than the setting an alarm and/or vibration will alert you.*Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.● Select [Rx-BATT.] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.● Select [BATTERY] in the RECEIVER screen and access the setup screen shown below by pushing the RTN button.●A setup of the voltage on which the alarm operates.Scrolling● Moving cursor● Receiver battery voltage ● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.● ↓The "down" arrow will indicate that an alarm will sound when the voltage drops to below the setting.● ALARM is chosen from BUZZER, VOICE, and INHIBIT. ● The ON/OFF switch of SPEECH is chosen.Alarm set 1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN.2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate.3. Move the cursor to the LIMIT [4.0V] item and push the RTN button to switch to the data input mode. 4. Ajust the rate by scrolling the edit dial. Initial value: 4.0V Adjustment range: 0.0V~100.0V*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.

71<Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.● Select [Rx-BATT.] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.Alarm set 1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, and INHIBIT, and pushes RTN.2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate.3. Move the cursor to the LIMIT [4.0V] item and push the RTN button to switch to the data input mode. 4. Ajust the rate by scrolling the edit dial. Initial value: 4.0V Adjustment range: 0.0V~100.0V*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.TELEMETRY : RECEIVER [EXT BATT.] Displaying data from the EXT battery voltage portThe EXT-VOLT screen will display the data from the EXT-battery output from the R7008SB receiver. In order to use this function, it is necessary to connect external voltage connector of the R7008SB receiver to a CA-RVIN-700 or SBS-01V to the battery you desire to measure the voltage of the EXT-battery.You will be alerted by an alarm or vibration if the voltage set by you is exceeded.*FMR-03 isn't equipped with EXT-battery port.*Only receiver voltage will be received in the FASSTest 12CH mode.*The FASSTest 18CH mode will display all telemetry data.*CA-RVIN-700 must be installed in the aircraft.● Select [EXT BATT.] in the RECEIVER screen and access the setup screen shown below by pushing the RTN button.●A setup of the voltage on which the alarm operates.Scrolling● Moving cursor● EXT battery voltage ● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.● ↓The "down" arrow will indicate that an alarm will sound when the voltage drops to below the setting.● ALARM is chosen from BUZZER, VOICE, and INHIBIT. ● The ON/OFF switch of SPEECH is chosen.

72 <Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.TELEMETRY : TEMPERATURE Displaying data from the temperatureTemperature is a screen which displays/sets up the temperature information from an optional temperature sensor. The temperature of the model (engine, motor, battery, etc.) which is ying can be displayed.If it becomes higher or lower than the setting an alarm and/or vibration will alert you.*Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.● Select [TEMPERATURE] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.Scrolling● Moving cursor● Temperature● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.● ↓ A downward arrow will show that an alarm will sound when the temperature drops below the set value.● ↑ An upward arrow will show that an alarm will sound when the temperature rises above the set value.Alert set : Hot warning 1. Move the cursor to the ↑ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [ ℃] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 100℃ Adjustment range: 0℃~200℃(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)Alert set : Low-temperature warning1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [ ℃] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 0℃ Adjustment range: 0℃~200℃(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)*A temperature sensor must be installed in the aircraft.●Select [TEMPERATURE](small font display) in the TEMPERATURE screen and access the setup screen shown below by pushing the RTN button.● The ON/OFF switch of SPEECH is chosen.●A setup of the temperature on which the alarm operates.TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.

73<Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.TELEMETRY : RPM SENSOR Displaying data from the RPMRPM sensor is a screen which displays / sets up the rotation information from an optional RPM sensor. The rotation of the model (engine, motor, etc.) which is ying can be shown.If it becomes higher or lower than the setting an alarm and/or vibration will alert you. *Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.Alarm set : Over rotations 1. Move the cursor to the ↑ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [2,000rpm] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 2,000rpm Adjustment range: 0rpm~150,000rpm(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)Alarm set : Under rotations1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [0rpm] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 0rpm Adjustment range: 0rpm~150,000rpm(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)*A RPM sensor must be installed in the aircraft.● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.●A setup of the revolution on which the alarm operates.● Select [RPM sensor] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.Scrolling● Moving cursor● RPM●"MAGNET" or "OPTICS" is set according to the sensor you use.SBS-01RM : MAGNETSBS-01RO : OPTICS● ↓A downward arrow indicates that the alarm will sound when the RPM falls below the set value.● ↑An upward arrow indicates that the alarm will sound when the RPM rises above the set value.● In "MAGNET", the gear ratio of your engine (motor) you are using is entered. ● In "OPTICS", the number of blades of the propeller ( r o t o r ) your model is entered. ●Select [ROTATION](small font display) in the RPM sensor screen and access the setup screen shown below by pushing the RTN button.● The ON/OFF switch of SPEECH is chosen.TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.

74 <Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.TELEMETRY : ALTITUDE Displaying data from the altitudeALTITUDE is a screen which displays / sets up the altitude information from an optional altitude sensor or GPS sensor. The altitude of the model which is flying can be known. If it becomes higher (low) than preset altitude, you can be told by alarm. To show warning by vibration can also be chosen. Data when a power supply is turned on shall be 0 m, and it displays the altitude which changed from there. Even if the altitude of an aireld is high, that shall be 0 m and the altitude difference from an airfield is displayed. This sensor calculates the altitude from atmospheric Pushure. Atmospheric Pushure will get lower as you go up in altitude, using this the sensor will estimate the altitude. Please understand that an exact advanced display cannot be performed if atmospheric Pushure changes in a weather situation.*Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.● Select [ALTITUDE] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.Scrolling● Moving cursor● Altitude● ↓ A downward arrow indicates the alarm will sound when the altitude reaches below your set value.● ↑ An upward arrow indicates the alarm will sound when the altitude reaches above your set value.First, the set of a reference is required.1. The model and transmitter to which the altitude sensor was connected are turned on. 2. Move the cursor to the [PRESET] of "REFERENCE" item. 3. Push the RTN button is pushed for 1 second. (To terminate the input and return to the original state, push the Home/Exit button.) *Atmospheric Pushure is changed according to the weather also at the same aireld. You should preset before a ight.Alarm set : High side 1. Move the cursor to the ↑ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [m] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 200m Adjustment range-500m~+3,000m(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)Alarm set : Low side1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [m] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: -50m Adjustment range-500m~+3,000m(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)*An altitude sensor or GPS sensor must be installed in the aircraft.●Select [ALTITUDE](small font display) in the TEMPERATURE screen and access the setup screen shown below by pushing the RTN button.● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.●The ON/OFF switch of SPEECH is chosen.●If this is set to MODE1-4, a rise and dive are told by a different melody.MODE1: Little rise/dive→Melody changes (sensitively) MODE4: Big rise/dive→Melody changes (insensible) . . .TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.

75<Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.● Select [ALTITUDE] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.TELEMETRY : ALTITUDE [VARIOMETER] Displaying data from the variometerVARIO is a screen which displays / sets up the variometer information from an optional altitude sensor or GPS sensor. The variometer of the model which is ying can be known.If it becomes higher or lower than the setting an alarm and/or vibration will alert you.To ensure that the pilot is aware as to the model's status, the FMT-03 incorporates a different melody for ascent and descent. Additionally, depending upon the rate of climb or descent, the tones vary to indicate whether or not the airplane is climbing or descending at a rapid rate. *Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.Alert set : Rise side 1. Move the cursor to the ↑ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [m/s] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: +1m Adjustment range -50m/s~+50m/s(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)Alert set : Dive side1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [m/s] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: -1m Adjustment range -50m/s~+50m/s(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)*An altitude sensor or GPS sensor must be installed in the aircraft.●If this is set to MODE1-4, a rise and dive are told by a different melody.MODE1: Little rise/dive→Melody changes (sensitively) MODE4: Big rise/dive→Melody changes (insensible) . . .Scrolling● Moving cursor● ↓ A downward arrow indicates the alarm will sound when the variomete reaches below your set value.● ↑ An upward arrow indicates the alarm will sound when the variometer reaches above your set value.TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.●Select [VARIOMETER](small font display) in the TEMPERATURE screen and access the setup screen shown below by pushing the RTN button.● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.● Variometer●The ON/OFF switch of SPEECH is chosen.

76 <Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.In this screen, the battery voltage is displayed. In order to use this function, it is necessary to connect External voltage connector of FMR-03 ⇔ SBS-01V ⇔ Battery SBS-01V measures two batteries. The power battery connected to two lines is displayed on EXT-VOLT. The battery for receivers connected to 3P lines is displayed here. *Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.*SBS-01V must be installed in the aircraft.＜Two examples of wiring are shown ＞*Refer to the manual of SBS-01V for the details of wiring.Drive battery （EXT Battery)SwitchPower supplies for servosAnother power supply Hub S.BUS2servosDrive battery are measured (SBS-01V use) Drive battery and power supplies for servos are measured (SBS-01V use)●Battery voltage measurement for receivers [FMR-03 use]●Battery voltage measurement for receivers [SBS-01V use]●The drive battery is measured in an EXT line [SBS-01V use]●Battery voltage measurement for receivers [FMR-01 use]●The drive battery is measured in an EXT line [SBS-01V use]●The voltage for servos is measured in a power supply line [SBS-01V use]Normal LineEXT LineEXT Line*SBS-01V measures two voltage. One corresponds to high voltages, such as a drive battery, with an EXT line. Another is a normal line and is measurement of the battery for receivers of a line connected to 3P connector, or the battery for servos.*The same receiver batteryReceiver battery Drive battery （EXT Battery)TELEMETRY : VOLTAGE [BATTERY] Displaying data from the battery voltage●Select [VOLTAGE] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.●Select [BATTERY] in the VOLTAGE screen and access the setup screen shown below by pushing the RTN button.●A setup of the voltage on which the alarm operates.Scrolling● Moving cursor●Battery voltage ●The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.●↓The "down" arrow will indicate that an alarm will sound when the voltage drops to below the setting.●ALARM is chosen from BUZZER, VOICE, and INHIBIT. ●The ON/OFF switch of SPEECH is chosen.Alarm set 1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN.2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate.3. Move the cursor to the LIMIT [4.0V] item and push the RTN button to switch to the data input mode. 4. Ajust the rate by scrolling the edit dial. Initial value: 4.0V Adjustment range: 0.0V-100.0V*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.

77<Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.Alarm set 1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, and INHIBIT, and pushes RTN.2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate.3. Move the cursor to the LIMIT [4.0V] item and push the RTN button to switch to the data input mode. 4. Ajust the rate by scrolling the edit dial. Initial value: 4.0V Adjustment range: 0.0V~100.0V*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)TELEMETRY : VOLTAGE [EXT-VOLT] Displaying data from the EXT battery voltage portIn this screen, the EXT battery voltage is displayed. In order to use this function, it is necessary to connect External voltage connector of FMR-03 ⇔ SBS-01V ⇔ Battery SBS-01V measures two batteries. The power battery connected to two lines is displayed on EXT-VOLT. *Only receiver voltage will be received in the FASSTest 12CH mode.*The FASSTest 18CH mode will display all telemetry data.*SBS-01V must be installed in the aircraft.● Select [VOLTAGE] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.● Select [EXT BATT.] in the RECEIVER screen and access the setup screen shown below by pushing the RTN button.●A setup of the voltage on which the alarm operates.Scrolling● Moving cursor● EXT battery voltage ● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.● ↓The "down" arrow will indicate that an alarm will sound when the voltage drops to below the setting.● ALARM is chosen from BUZZER, VOICE, and INHIBIT. ● The ON/OFF switch of SPEECH is chosen.TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.

78 <Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.TELEMETRY : GPS [DISTANCE] Displaying data from the Distance ScreenThe Distance screen displays and sets altitude data from an SBS-01G GPS Sensor (sold separately), and allows the distance to the airborne aircraft to be read by the transmitter. When the aircraft flies inside or outside the set distance an alarm and vibration alerts the pilot.*The GPS sensor is necessary, and is sold separately. Mount and connect the sensor in accordance with the sensor instruction manual. *Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.*A GPS sensor must be installed in the aircraft.●This indicates the receiving accuracy from a GPS Satellite. When three bars are displayed, the GPS is ready for use.SurfaceAltitudeSlant●Altitude calculated as either straight　line distance (slant) or surface distance on a map can also be selected.●Select <SLANT> <SURFACE> to “DISTANCE MODE”, scroll either to the desired method and push the RTN button.*Positioning time of GPSWhen powered up, the SBS-01G begins to acquire GPS satellite data. This process can take several minutes. Please do not move the model during this process. During acquisition, the LED on the SBS-01G will blink green; after the satellites signals have been acquired, the LED will become solid green, and the GPS signal strength display on the transmitter will show three bars.Moving the model before the satellites are fully acquired will cause a delay in acquiring the satellite signal.● Select [GPS] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.Scrolling● Moving cursor● Distance● ↓ A downward arrow indicates the alarm will sound when the distance reaches below your set value.● ↑ An upward arrow indicates the alarm will sound when the distance reaches above your set value.●Select [DISTANCE](small font display) in the TEMPERATURE screen and access the setup screen shown below by pushing the RTN button.● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.●The ON/OFF switch of SPEECH is chosen.●Move the cursor to the [PRESET] of "REFERENCE" item. Push the RTN button is pushed for 1 second. Sets the current aircraft position as the starting point.TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.● Push the S1 button to call next page.

79<Functions of Linkage Menu>First, setting the pointos of reference is required.1. The model and transmitter on which the GPS sensor is connected are turned on. 2. Move the cursor to the [PRESET] of "REFERENCE" item. 3. Push the RTN button is pushed for 1 second. (To terminate the input and return to the original state, push the Home/Exit button.) *Now, the position of the present model was set to 0 m.Setting a "too far" alarm distance 1. Move the cursor to the ↑ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [m] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 1,000m Adjustment range 0m~3,000m(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)Setting a "too close" alarm distance1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [m] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 0m Adjustment range 0m~3,000m(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)DistanceSpeedposition

80 <Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.TELEMETRY : GPS [SPEED] Displaying data from the speedThe speed screen displays and sets the speed data from an SBS-01G (GPS sensor) sold separately.The speed of the aircraft during ight can be displayed. After flight, the maximum speed during flight can be viewed. Because this speed is based on position data from a GPS satellite, the ground speed is displayed instead of air speed. Consequently, with a head wind, the displayed speed decreases and with a tail wind, the displayed speed increases.*The GPS sensor is necessary, and is sold separately. Mount and connect the sensor in accordance with the sensor instruction manual. *Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.*A GPS sensor must be installed in the aircraft.●This indicates the receiving accuracy from a GPS Satellite. When three bars are displayed, the GPS is ready for use.● Select [GPS] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.Scrolling● Moving cursor● Speed● ↓ A downward arrow indicates the alarm will sound when the speed reaches below your set value.● ↑ An upward arrow indicates the alarm will sound when the speed reaches above your set value.●Select [SPEED](small font display) in the TEMPERATURE screen and access the setup screen shown below by pushing the RTN button.● The maximum and the minimum when powering ON are shown. It will be preset, if a cursor is moved to this place and the RTN button is pushed for 1 second.●The ON/OFF switch of SPEECH is chosen.●It links with the "DISTACE" display.●Pushing [PRESET] sets the current aircraft position as the starting point.Alarm setting when speed increases 1. Move the cursor to the ↑ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [km/h] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 200km/h Adjustment range 0km/h-500km/h(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)Alarm setting when speed decreases1. Move the cursor to the ↓ALARM item, and it chooses from BUZZER, VOICE, INHIBIT, and pushes RTN. 2. When not operating vibrator, it is "VIBRATOR" to INHIBIT. TYPE1-3 will be chosen if it is made to operate. 3. Move the cursor to the LIMIT [km/h] item and push the RTN button to switch to the data input mode.4. Ajust the rate by scrolling the edit dial. Initial value: 0km/h Adjustment range 0km/h-500km/h(↑LIMIT ≧ ↓LIMIT)*When the RTN button is pushed for one second, the rate is reset to the initial value.5. Push the RTN button. (To terminate the input and return to the original state, push the Home/Exit button.)*Speed alarm precautionSince the GPS speed sensor displays the ground speed, it cannot be used as a stall alarm. For example, an aircraft that stalls at 50km/h will stall if the tailwind is 5km/h or greater even through 55km/h is displayed by ground speed. In addition, with an aircraft that will fail in midight at 400km/h at an over-speed alarm, when the headwind reaches 30km/h the airplane will fail in midair due to over speeding even at a ground speed of 370km/h.TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.● Push the S1 button to call next page.

81<Functions of Linkage Menu>S1● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.<Edit dial>TELEMETRY : GPS [ALTITUDE, VARIOMETER, POSITION]The altitude, variometer, position screen displays and sets the data from an SBS-01G (GPS sensor) sold separately.*The GPS sensor is necessary, and is sold separately. Mount and connect the sensor in accordance with the sensor instruction manual. *Only receiver voltage can be used in FASSTest 12CH mode.*The FASSTest 18CH mode can use all the telemetry functions.*A GPS sensor must be installed in the aircraft.● Push S1 button to advance to next page.●This indicates the receiving accuracy from a GPS Satellite. When three bars are displayed, the GPS is ready for use.● Select [GPS] in the TELEMETRY screen and access the setup screen shown below by pushing the RTN button.● Refer to the former page for a setup about ALTITUDE and VARIOMETER. ● Push S1 button to advance to next page.● The position of the present model is displayed.Scrolling● Moving cursor● Push the S1 button to call next page.

82 <Functions of Linkage Menu>TELEMETRY : Servo sensor [Current] [Temperature] [Angle]The SBS-01S can monitor and display the in-flight current, operating angle, and internal temperature of up to two S.BUS2 servos.If you forget to connect the servo wiring during fuselage assembly, or the servo was disconnected, an alarm can be activated at the transmitter.*Only receiver voltage will be received in the FASSTest 12CH mode.*The FASSTest 18CH mode will display all telemetry data.*SBS-01S must be installed in the aircraft.SBS-01StoS.BUS2 portS.BUS servoServo sensor screenCalling of a servo sensor screen.①[Linkage menu]→[Telemetry]②Select [SERVO SENS] in the TELEMETRY screen and access the next screen shown below by pushing the RTN button.The current and the temperature of servo 1To current setup screenTo temperature setup screenThe current and the temperature of servo 21/4 : Servo1: Current・Temp2/4 : Servo1: Angle Servo2: Current3/4 : Servo2: Temp・Angle4/4 : Servo1・2 : ConnectPageMax. and min. values since the power was turned ON will display.Alarm settingA setup of the current on which the alarm operates. Alarm is chosen from Buzzer, Voice, and Inhibit.The ON/OFF switch of Speech is chosen.↑ An upward arrow indicates the alarm will sound when the current reaches above your set value.↓ A downward arrow indicates the alarm will sound when the current reaches below your set value. TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.Connect Alarm settingWhen the Alarm or Vibrator options are activated, the servo connection will display.*This alarm and display is limited to the S.BUS servos connected to the servo sensors.If you forget to connect the servo wiring during fuselage assembly, or the servo was disconnected, an alarm can be activated at the transmitter.

83<Functions of Linkage Menu>Current sensor screenAlarm settingCalling of a current sensor screen.①[Linkage menu]→[Telemetry]②Select [Current] in the TELEMETRY screen and access the next screen shown below by pushing the RTN button.A setup of the current on which the alarm operates. Alarm is chosen from Buzzer, Voice, and Inhibit.The ON/OFF switch of Speech is chosen.↑ An upward arrow indicates the alarm will sound when the current reaches above your set value.↓ A downward arrow indicates the alarm will sound when the current reaches below your set value.PageDriveBatterySBS-01CTo ReceiverMotorESC*Current sensor must be installed in the aircraft.TELEMETRY : Current sensor [Current] [Voltage] [Capacity]The SBS-01C has the capability of measuring current, voltage and capacity (consumption) from drive battery at the same time. *Only receiver voltage will be received in the FASSTest 12CH mode.*The FASSTest 18CH mode will display all telemetry data.1/2 : Current・Voltage2/2 : CapacityMax. and min. values since the power was turned ON will display.TYPE 1TYPE 2TYPE 3"VIBRATOR" typeIf the following types are selected, the transmitter will vibrate during the warning.To current setup screenTo voltage setup screenPage

84 <Functions of Linkage Menu>S1● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.<Edit dial>SENSOR Various telemetry sensors settingThis screen registers the telemetry sensors used with the transmitter. When only one of a certain type of sensor is used, this setting is unnecessary and the sensor can be used by simply connecting it to the S.BUS2 port of the transmitter.When using 2 or more of the same kind of sensor, they must be registered here. ● Select [SENSOR] in the Linkage menu and access the setup screen shown below by pushing the RTN button.● As shown in the table below, an altimeter requires 3 contiguous slots and a GPS sensor requires 8 contiguous slots. In addition, since the GPS (SBS-01G) start slots are 8, 16, and 24. ＜Assignable slot ＞*Altimeter, GPS, and other sensors that display a large amount of data require multiple slots.*Depending on the type of sensor, the slot numbers that can be allocated may be limited.[What is a slot?]Servos are classified by CH, but sensors are classied in units called “slot”. There are slots from #1 to #31.Altitude sensors, GPS sensors and other data sensor units may use multiple slots.Using a sensor which uses two or more slots, the required number of slots is automatically assigned by setting up a start slot.When 2 or more of the same kind of sensor are used, the sensors themselves must allocate unused slots and memorize that slot.*3 slots of altitude sensor are used.*8 slots of GPS sensor are used.Sensor The required number of slots The number which can be used as a start slot Selling areaTEMP (SBS-01T/TE) 1 slot 1 ～31GlobalRPM (SBS01RM/RO/RB) 1 slot 1 ～31Voltage (SBS-01V) 2 slots 1,2,3,4,5,6,8,9,10,11,12,13,14,16,17,18,19,20,21,22,24,25,26,27,28,29,30Altitude (SBS-01A/02A) 3 slots 1,2,3,4,5,8,9,10,11,12,13,16,17,18,19,20,21,24,25,26,27,28,29Current (SBS-01C) 3 slots 1,2,3,4,5,8,9,10,11,12,13,16,17,18,19,20,21,24,25,26,27,28,29S.BUS Servo (SBS-01S) 6 slots 1,2,8,9,10,16,17,18,24,25,26GPS (SBS-01G) 8 slots 8,16,24TEMP125-F1713 1 slot 1 ～31EuropeVARIO-F1712 2 slots 1,2,3,4,5,6,8,9,10,11,12,13,14,16,17,18,19,20,21,22,24,25,26,27,28,29,30VARIO-F1672 2 slots 1,2,3,4,5,6,8,9,10,11,12,13,14,16,17,18,19,20,21,22,24,25,26,27,28,29,30GPS-F1675 8 slots 8,16,24Scrolling● Moving cursor● Push S1 button to advance to next page.● Push S1 button to advance to next page.● Push the S1 button to call next page.

85<Functions of Linkage Menu>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.● Call page 3/3 by pushing the S1 button 2 times from the [SENSOR] menu.● Call page 3/3 by pushing the S1 button 2 times from the [SENSOR] menu.SENSOR : RELOADSENSOR : REGISTERThis page is set when using multiple telemetry sensors of the same type.This page is set when using multiple telemetry sensors of the same type.When using multiple sensors of the same type the sensors must be registered in the transmitter. Connect all the sensors to be used to the FMT-03 as shown in the gure at the right and register them by the following procedure. The ID of each sensor is registered in the transmitter.This function registers an additional sensor. Connect the sensor as shown in the figure at the right and register it by the following procedure. The sensor ID is registered in the transmitter.All the sensors to be used are connected. SENSORSENSOR3-way hub or Y-harnessesSENSORSENSORSENSORFMT-03FMT-03SENSORReading all the sensors to be used1. Connect all the sensors to be used to the FMT-03 through a hub as shown in the gure above.2. Move the cursor to “RELOAD” on page 3/3 of the [SENSOR] screen.3. Push the RTN button. All the sensors are registered and can be used.Additional sensor registration1. Connect the sensor to be used to the FMT-03 through a hub as shown in the gure at the right.2. Move the cursor to “REGISTER” on page 3/3 of the <Sensor> screen.3. Push the RTN button. The sensor is registered and can be used.*When the number of slots needed in registration is insufcient, an error is displayed and registration cannot be performed. Disable unused slots or perform the following relocate.*It is not necessary to carry out multiple connection of the battery like a T18MZ/T14SG. (It will damage, if it connects.)*It is not necessary to carry out multiple connection of the battery like a T18MZ/T14SG. (It will damage, if it connects.)● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.

86 <Functions of Linkage Menu>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.● Call page 3/3 by pushing the S1 button 2 times from the [SENSOR] menu.This procedure changes the slot number of one registered sensor.Sensor slot change1. Connect the sensor to be changed to the FMT-03 through a hub as shown in the gure above.2. Move the cursor to “CHANGE SLOT” on page 3/3 of the <Sensor> screen.3. Push the RTN button. A sensor details screen appears.4. Move the cursor to “READ” and push the RTN button.5. The current start slot is displayed. Move the cursor to the number of the start slot and change it to the desired value.（Cannot be set to a slot that cannot be allocated like the table of all pages.）6. Move the cursor to “WRITE” and push the RTN button.SENSOR : CHANGE SLOTFMT-03SENSORThis page is set when using multiple telemetry sensors of the same type.● Select [CHANGE SLOT] in the SENSOR screen and access the setup screen shown below by pushing the RTN button.*It is not necessary to carry out multiple connection of the battery like a T18MZ/T14SG. (It will damage, if it connects.)

87<Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.● RECEIVER : Data from a receiver is recorded.● TRAINER : Data from a trainer connector is recorded. *The special use for which usual isn't used.TELE. SETTING Speech interval set, data logging of telemetry.The set of the speech interval of telemetry data, and a switch setup for carrying out logging of the telemetry data to micro SD card and a setup of a logging interval are carried out. Telemetry data can be checked with PC after a ight.*The software which displays the logging data of micro SD card on PC has not been put on the market yet. Speech interval setting1. Select the Linkage Menu [TELE. SETTING] and push the RTN button.2. The TELE. SETTING setup screen is displayed.3. Select numerical value beside[SPEECH INTERVAL] and push the RTN button.4. Ajust the time by scrolling the edit dial. Initial value: 0 Adjustment range 0~305. Push the RTN button.Logging switch setting1. Select the Linkage Menu [TELE. SETTING] and push the RTN button.2. The TELE. SETTING setup screen is displayed.3. Select [OFF] beside [LOGGING SWITCH] and push the RTN button.4. Move the cursor to the [SWITCH] item and call the switch setup screen by pushing the RTN button and select the switch and ON direction.(For a detailed description of the setting method, see [Switch Setting Method] at the end of this manual.)Logging interval setting1. Select the Linkage Menu [TELE. SETTING] and push the RTN button.2. The TELE. SETTING setup screen is displayed.3. Select numerical value beside [LOGGING INTERVAL] and push the RTN button.4. Ajust the time by scrolling the edit dial. Initial value: 0 Adjustment range 0~1005. Push the RTN button.● Select [TELE. SETTING] at the linkage menu and call the setup screen shown below by pushing the RTN button.Scrolling● Moving cursor● Selecting mode● Adjusting value

88 <Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.WARNING Mixing warning normal resetThe warning display at power ON can be turned ON/OFF for each function. Use by setting functions which may be dangerous if operated at power ON to ON. Initial setting is all ON.Warning ON/OFF setting 1. The settings can be changed individually. When set to [OFF], a warning is not displayed at power ON.● Select [WARNING] at the linkage menu and call the setup screen shown below by push the RTN button.Scrolling● Moving cursor● Selecting mode

89<Functions of Linkage Menu>TRAINER Trainer system starting and settingFMT-03 trainer system makes it possible for the instructor to chose which channels and operation modes that can be used in the students transmitter. The function and rate of each channel can be set, the training method can also be matched to the student's skill level. Two FMT-03s must be connected by an optional Trainer Cord, and the Instructors’ transmitter should be programmed for trainer operation, as described below.When the Instructor activates the trainer switch, the student has control of the aircraft (if MIX/ FUNC/NORM mode is turned on, the Instructor can make corrections while the student has control). When the switch is released the Instructor regains control. This is very useful if the student gets the aircraft into an undesirable situation.● Setting data are stored to model data.● Student rate can be adjusted at MIX/FUNC/NORM mode.● Activated student channels can be selected by switches.NOTE: This trainer system can be used in the following manner;1. With the FMT-03 transmitter and a conventional transmitter, if the channel order is different, it is necessary to match the channel order before using this function. You can select the channel of input data from student's transmitter in the "FUNC" or "MIX" mode.2. A transmitter of anything but FMT-03 doesn't correspond to this trainer system.3. Be sure that all channels work correctly in both transmitters before ying.

90 <Functions of Linkage Menu>S1● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.<Edit dial>When using at the teacher side1. Select the mode.*When changing the mode, use the edit dial to move to the item you want to change and push the RTN button to switch to the data input mode and change the mode by turning the edit dial to the left or right. The display blinks. Push the RTN button to change the mode. "TEACHER/STUDENT": Select [TEACH]. "ACT/INH": Enable operation by changing to [OFF] or [ON]. "CHANNEL MODE": Select [16CH]. 2. Select the trainer switch.*When setting or changing the switch, use the edit dial to move to the "SWITCH" item, call the switch setup screen by pushing the RTN button and set the desired switch and ON/OFF direction. (See "Switch selection method" at the end of this manual for selection method details.)*The switch mode can also be selected when setting the ON position on the switch setup screen. When [NORM] is selected, normal ON/OFF operation is performed. When [ALTERNATE] is selected, the trainer function is alternately turned on and off each time the switch is operated. . Note: The trainer function won’t be turned on unless the Instructor's transmitter receives signals from the student's transmitter. Be sure to confirm this after connecting your trainer cable.3. Select the operating mode for each channel.● Select [TRAINER] at the system menu and call the setup screen shown below by pushing the RTN button.When using at the student side1. Select the mode.*When changing the mode, use the edit dial to move to the item you want to change and push the RTN button to switch to the data input mode and change the mode by turning the edit dial to the left or right. The display blinks. Push the RTN button to change the mode. "TEACHER/STUDENT": Select [STUD] (student). "ACT/INH": Enable operation by changing to [ON]. "CHANNEL MODE": Select [16CH]. Note: In "student mode", only the teacher side can turn on and off the power to the student's transmitter. Keep the power switch always at off position.Scrolling● Moving cursor● Selecting mode

91<Functions of Linkage Menu>*Use the edit dial scrolling to move the cursor to the "MODE" item of the channel you want to change and push the RTN button to switch to the data input mode and change the mode by turning the edit dial to the left or right. The display blinks. Push the RTN button to change the mode. "NORM": The model is controlled by signals from the student transmitter. "MIX" mode: The model is controlled by signals from the teacher and student transmitters. (Reset the student's model data to the default condition.) "FUNC" mode (function mode): The model is controlled by signals from the student transmitter with the teacher AFR setting. (Reset the student's model data to the default condition.) "OFF": Only the teacher side operates.*The setting above allows setting of the servo throw relative to the amount of student side operation when [MIX] or [FUNC] was selected. When changing the rate, use the edit dial scrolling to move the cursor to the [RATE] item of the channel you want to change and use the edit dial to adjust the rate. Setting range: -100~+100 Initial value: +100 Push the RTN button to end adjustment and return to the cursor move mode.*When the RTN button is pushed for 1 second, the rate is reset to the initial value.3. Set the switch of each channel.*When setting the switch at each channel, use the edit dial to move to the "SW" item of the channel you want to change, call the switch setup screen by pushing the RTN button, and select the switch. "--" : Always ON. "SA"-"SH": The switch which enables student side operation can be selected. (See "Switch selection method" at the end of this manual for selection method details.)Trainer student channel setting function Which channel of the signal from the student's transmitter can be assigned as the instructor functions input signal when "FUNC" or "MIX" was set as the trainer function instructor's transmitter mode setting can be set. This makes trainer connection easy even when the instructor side and student side channel assignment is different.*When the instructor's transmitter mode is set to "NORM", the signal of the same channel of the student's transmitter is output as is. (The same as before.)

92 <Functions of Linkage Menu>S1<Edit dial>● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.●When INH is selected, the function cannot be used. When ON or OFF is selected, the function is activated. ON and OFF changes are linked to the switch.●The current throttle stick position.●e.g., Always to make them stick alarm in spite of switch.●Select " －－ " ●Select "ON" ● Stick alarm position.STICK ALARM Throttle stick positional alarmAn alarm (single beep) can be sounded at the specied throttle stick position.*Alarm function ON/OFF can be set by switch. Scrolling● Moving cursor● Selecting mode● Adjusting value100%50%0%Stick alarm setting procedure*Perform the following settings after using the edit dial to move the cursor to the item you want to set.1. Activate the function: Move the cursor to the [ACT/INH] item and push the RTN button to switch to the data input mode. Switch the blinking from "INH" to "ACT" by turning the edit dial to the left and then push the RTN button.2. Switch setting: Move the cursor to the [SWITCH] item, call the switch setup screen by pushing the RTN button, and select the switch and ON direction.(For a detailed description of the setting method, see [Switch Setting Method] at the back of this manual.)3. Alarm position setting: Move the cursor to the [POSITION] item and push the RTN button to switch to the data input mode. Adjust the alarm position operation by turning the edit dial to the left or right. Initial value: 50% Adjustment range: 0%-100%(When the RTN button is pushed for 1 second, the offset rate is reset to the initial value.) Push the RTN button to end adjustment and return to the cursor move mode.● Select [STICK ALARM] at the linkage menu and call the setup screen shown below by pushing the RTN button.

93<Functions of Linkage Menu>S1● Select the function name and return to the Linkage menu by pushing the RTN button or pushing the Home/Exit button.<Edit dial>DATA RESET Model memory setting data reset. (by item)This function is designed to allow you to reset selected portions or all of the settings saved in the active model memory. You may individually choose to reset the following sets of data;T1-T6:Reset the digital trim setting.*All the conditions, or the condition currently being displayed (the entire group for group setting), can be selected.*The trim step amount and trim rate are not reset.Data resetting method1. Move the cursor to the item you want to reset and push the RTN button.*A conrmation message appears.2. Execute reset by pushing the RTN button again. (Operate edit dial or S1 button to stop resetting.) [T1-T6 (ALL CONDITION)]: Resets only the T1-T6 (all conditions) [T1-T6 (CURRNT+GROUP COND.)]: Resets only the data of T1-T6 (condition in use and all the conditions set to group mode) [MODEL MENU SETTING]: Resets all the functions in the model menu, except the condition selection functions.Model menu setting:Resets all the functions in the Model menu except condition select.All model setting:Resets all Linkage and Model menu functions except for frequency, model select, and model type.Function Name:A function name is reset.Telemetry:Reset the telemetry setting. [ALL MODEL SETTING]: Resets all the functions in the linkage menu and model menu except the frequency, model select, and model type functions. [FUNCTION NAME]: Resets only the function name functions. [TELEMETRY]: Resets only the telemetry functions.● Select [DATA RESET] at the linkage menu and call the setup screen shown below by pushing the RTN button.Scrolling● Moving cursor● Push S1 button to advance to next page.● Push the S1 button to call next page.

94 <Model Menu (Common Functions)>●Selectthe[MODELMENU]andreturnto the homescreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.MODEL MENU (COMMON FUNCTIONS)This section describes the AFR, program mixing, and other functions common to all model types.Before setting the model data, use the Model Type function of the Linkage Menu to select the model type matched to the fuselage. When another model type is selected thereafter, the AFR, program mixing, and other setting data will be reset.The functions in the Model Menu can be set for each flight condition. When you want to use the system by switching the settings for each condition by switch, stick position, etc., use the Condition Select function to add flight conditions. (Up to 8 conditions can be used)Note:Thesetupscreensintheinstructionmanualaretypicalexamples.(Model Menu screen example)*The Model Menu screen depends on the model type. Model Menu functions (Common) list●SERVO MONITORServo test and servo position display (For a description of its functions, see the Linkage Menu section.)●COND.SELECTFlight conditions addition, deletion, copy, condition renaming, and condition delay can be set. ●AFRSets the function rate and curve of all the operation functions. ●DUAL RATEA D/R curve which can be switched with a switch, etc. can also be added.●PROG. MIXProgram mixing which can be freely customized. Up to 10 mixes can be used for each condition.●GYROThis is a dedicated mix when a Futaba GY series gyro is used.●Selectthe[MODEL]atthehomescreen and call themodelmenushownbelowbypushingtheRTNbutton.●UsetheeditdialtoselectthefunctionyouwanttosetandcallthesetupscreenbypushingtheRTNbutton.S1<Editdial> Scrolling●Movingcursor●Callingsetupscreen

95<Model Menu (Common Functions)>S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>CONDIT. SELECT Flightcondition'saddition,deletion,copy,conditionrenaming,andconditiondelaycanbeset.[Allmodeltypes]The functions in the Model Menu can be used by switching the settings of up to 8 flight conditions by using the Condition Select function to add ight conditions. Add conditions, as required.When you do not want to use the Condition Select function, this setting is unnecessary. In this case, use the flight conditions assigned at initial setting.●Sinceswitchingbystickandleverposition,inadditiontoordinarytoggleswitch,ispossibleastheflightconditionselectorswitch,thisfunctioncanbelinkedwithotheroperations.●AConditionDelayfunctioncanbeset.Unnecessaryfuselagemotiongeneratedwhentherearesuddenchangesintheservopositionsandwhentherearevariationsintheoperatingtimebetweenchannelsduringconditionswitchingcanbesuppressed.Thedelaycanbesetforeachchannel.Whensettingthedelayfunctionattheswitchingdestinationcondition,therelatedfunctionchangesafteradelaycorrespondingtothesetamount.●Whenmultipleconditionswereset,theiroperationprioritycanbefreelychanged.●Theconditionnamecanbechanged.Theselectedconditionnameisdisplayed onthescreen.Whenacondition hasbeenadded,giveitanamewhichcanbeeasilyconrmed. (Conditions List)(Currently selected condition name)●Select[CONDIT.SELECT]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.(For a detailed description of the setting method, see [Switch Setting Method] at the back of this manual.)*The data (except the condition name) of the condition currently being used is copied to the added condition.Condition deletion1.UsetheeditdialtomovethecursortotheconditionyouwanttodeleteintheconditionslistandpushtheRTNbutton.*The number before the condition name become reverse-video to show that it is to be deleted.2.Movethecursorto[REMOVE]andpushtheRTNbutton.*A conrmation message is displayed.*Note that if initially operated up and down, the objective condition changes.3.WhentheRTNbuttonispushedagain,theconditionisdeleted.(OperatetheeditdialorS1buttontostopdeletion.) PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.Condition name change1.Usetheeditdialtomovethecursortotheconditionyouwanttochangeinthe*Perform the settings below after using the edit dial to move the cursor to the item you want to set.Condition addition1.UsetheeditdialtomovethecursortoanyconditionintheconditionslistandpushtheRTNbutton. Movethecursortotheconditionyouwanttoadd.2.Movethecursorto[ADD]andpushtheRTNbutton.*Only the number of the conditions which can be added is displayed.3.AddtheconditionbypushingtheRTNbuttonagain.PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.4.Movethecursorto[SWITCH]item,calltheswitchsetupscreenbypushingtheRTNbutton,andselecttheswitchandONdirectiontobeusedinconditionswitching.Scrolling●Movingcursor

96 <Model Menu (Common Functions)>conditionslist.*The number before the condition name become reverse-video to show that it is to be deleted.2.Movethecursorto[RENAME]andpushtheRTNbutton.*The condition name setup screen appears.3.Changetheconditionnameasdescribedbelow: [Movingcursorininputbox] Select[←]or[→],andpushtheRTNbutton. [Deletingacharacter] When[DELETE]isselectedandtheRTNbuttonispushed,thecharacterimmediatelyafterthecursorisdeleted. [Addingacharacter] WhenacandidatecharacterisselectedfromthecharacterlistandtheRTNbuttonispushed,thatcharacterisaddedatthepositionimmediatelyafterthecursor.*A name of up to 8 characters long can be entered as the condition name. (A space is also counted as 1 character.)5.Attheendofinput,select[ENTER]andpushtheRTNbutton.(Toterminateinputandreturntotheoriginalstate,select[CANCEL]andpushtheRTNbutton.)Condition copy1.UsetheeditdialtomovethecursortoanyconditionintheconditionslistandpushtheRTNbutton.2.Usetheeditdialtomoveto[COPY].3.PushtheRTNbutton.*The copy screen appears.4.Usetheeditdialtomovethecursortothe"SOURCECOND."(copysource)itemandpushtheRTNbutton.*The models already saved are displayed at the right side of the screen.5.Afterusingtheeditdialtomovethecursortothecopysourcecondition,pushtheRTNbutton.*The copy source condition is displayed at the "SOURCE COND." position.6.Usetheeditdialtomovethecursorto"DESTIN.CND."(copydestination)andpushtheRTNbutton.*The models already saved are displayed at the right side of the screen.7.Afterusingtheeditdialtomovethecursortothecopydestinationcondition,pushtheRTNbutton.*The copy destination conditions are displayed at the "DESTIN.COND." position.8.Usetheeditdialtomovethecursorto[COPY]andpushtheRTNbutton.9.WhentheRTNbuttonispushedagain,copyisexecuted.(OperateeditdialorS1buttontostopcopying.) PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.Priority change1.Usetheeditdialtomovethecursortotheconditionwhosepriorityyouwanttochangeintheconditionlist.2.Movethecursorto[UP]or[DOWN]of[PRIORITY]andpushtheRTNbutton.(Thelastconditionbecomesthehighestpriority.)*The initial setting condition cannot be shifted. The priority is the lowest.Condition delay setting1.UsetheeditdialtomovethecursortotheconditionyouwanttochangeintheconditionlistandpushtheRTNbutton.2.Movethecursorto[DELAY]andpushtheRTNbutton.*The condition delay setup screen appears.3.Usetheeditdialtomovethecursortothe"DELAY"itemofthechannelyouwanttosetandpushtheRTNbuttontoswitchtothedatainputmode. Adjustthedelayamountwiththeeditdial. Initialvalue:0 Adjustmentrange:0~27(maximumdelay) PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.● Thesettingmode(group[GROUP]/single[SINGLE]mode)canbeswitched.(For more information, see the description at the back of this manual.)

97<Model Menu (Common Functions)>S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>AFR Thefunctionrateandcurveofeachoperationfunctioncanbeset.[Allmodeltypes]AFR function is used to adjust the throw and operation curve of the stick, lever, and switch functions for each ight condition. This is normally used after End Point has defined the maximum throw. When mixing is applied from one channel to another channel, both channels can be adjusted at the same time by adjusting the operation rate through the AFR function.●Operationcurveadjustment:Threetypesofcurves(EXP1,EXP2,andPOINT)canbeselected.Amaximum17pointscurvecanbeusedforthepointcurvetype.(Initialsetting:9points)Thenumberofpointscanalsobeincreasedanddecreasedandcurvesfromcomplexcurvestosimplecurvescanbeused.●Operationspeedadjustment:Theoperationspeedofeachfunctionwhenthefunctionisoperated(includingatflightconditionswitching)canbeadjusted.Thefunctionoperatessmoothlyataconstantspeedcorrespondingtothesetspeed.(Currently selected condition name)(Number of D/R curves set at the currently selected condition)●Servospeedsetting(For a description of the setting method, see the description at the back of this manual.)●Group/singlemodeswitch(GROUP/SINGLE)(For more information, see the description at the back of this manual.)●Operationcurvesetting(For a description of the setting method, see the description at the back of this manual.)●Select[AFR]atthemodel menu and call the setupscreenshownbelowbypushingtheRTNbutton.Function selection method1.Usetheeditdialtomovethecursorto[FUNC.]andpushtheRTNbuttontoswitchtothedatainputmode.2.Selectthedesiredfunction byscrollingtheeditdialtotheleftorright,pushtheRTNbutton.*The setting mode (group [GROUP]/single [SNGLE] mode) can be switched (For more information, see the description at the back of this manual.)[AFR, D/R]: Displays the currently selected rate (AFR, D/R).●FunctionselectionScrolling●Movingcursor●Selectingmode●Adjustingvalue●Pushthe S1 buttontocallnextpage.

98 <Model Menu (Common Functions)>S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>Dual rate adding1.Movethecursortothe[INH]displayofanunusedD/RandpushtheRTNbuttontoswitchtothedatainputmode. TurnitoffbyscrollingtheeditdialtotheleftandactivatetheD/RfunctionbypushingtheRTNbutton.2.Movethecursortothe"FUNCTION"itemandpushtheRTNbuttontoswitchtothedatainputmode. SelectthefunctionbyscrollingtheeditdialandpushtheRTNbutton.3.Movethecursortothe[SWITCH]itemandcalltheswitchsetupscreenbypushingtheRTNbuttonandselecttheswitchandONdirection.Alternatemodecanbeassignedtodualrateswitch.(For a detailed description of the setting method, see [Switch Setting Method] at the end of this manual.)DUAL RATE [Allmodeltypes]D/R curves which can be switched by switch, etc. can be added. The curve can be adjusted by the AFR function.● Upto 6ratescan beaddedfor eachcondition.● D/Rissetforeachconditionandisnotreectedatotherconditions.● D/RatthetopoftheD/Rlisthaspriority.●Select[DUALRATE]at the model menu and call thesetupscreenshownbelowbypushingtheRTNbutton.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●Pushthe S1 buttontocallnextpage.

99<Model Menu (Common Functions)>S1●SelectthefunctionnameandreturntotheprecedingscreenbytouchingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>PROG. MIXES Programmixingwhichcanbefreelycustomized.Upto10mixingscanbeusedforeachcondition.[Allmodeltypes]Programmable mixing may be used to correct undesired tendencies of the aircraft, and it may also be used for unusual control congurations. Mixing means that the motion of a command channel, called the "master," is added to the motion of the mixed channel, called "slave."You may choose to have the Master's trim added to the Slave channel response ("Trim" setting). The mixing curve can be changed so that the undesired tendencies can be corrected effectively by setting the EXP1/EXP2/POINT modes. The Delay function can be programmed for each rate. The Delay is used to change the rate smoothly when switching mixes. You may dene Mixing ON/OFF switch, control or you may choose to have mixing remaining on all the time. Mixing ON/OFF delay time can be adjusted. The Programmable mixing includes a powerful link function, which allows Programmable mixing to be linked with the special mixing functions, or with other programmable mixing functions. The link function can be set up for Master and Slave channel individually.The slave channel AFR mode (STK-STK mode) may be selected, where the slave channel AFR and D/R settings are observed when Link function is set. The knob for ne tuning can be set up for every mixing circuit. (Fine tune function)The programmable mixing (in mixing mode) STK to STK mixing function can be used even when the Master is a stick or other hardware.(Currently selected condition name)●Select[PROG.MIXES]atthemodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.●Operationcurvesetting(For a description of the setting method, see the description at the back of this manual.)●MixoperatingdisplayMix setup screen call● MovethecursortothemixNo.whosefunctionyouwanttoactivateandcallthesetupscreenbypushingtheRTNbutton.*When the function is activated, the master and slave channel name or is displayed.●Group/singlemodeswitching(GROUP/SINGLE)(For more information, see the description at the back of this manual.)●CurrentmixnumberScrolling●Movingcursor●Selectingmode●Adjustingvalue●Pushthe S1 buttontocallnextpage.

100 <Model Menu (Common Functions)>*Perform the settings below after using the edit dial to move the cursor to the item you want to set.●Group/single mode selection1.Whenyouwanttoactivatefunctionsforonlyselectedconditions,movethecursortothe[GROUP]itemandpushtheRTNbuttontoswitchtothedatainputmode.2.Turntheeditdialtotheleftuntil[SINGLE]startstoblinkandthenpushtheRTNbutton.*The mode changes to the single mode [SINGLE].*When using common settings at each conditions, remain in the [GROUP] mode.●Activate the function.1.Movethecursorto[INH]andpushtheRTNbuttontoswitchtothedatainputmode.2.Turntheeditdialtotheleftuntil[ACT]startstoblinkandthenpushtheRTNbutton.*The function is activated. (ON or OFF display)*ON/OFF switch and mix rate are not set even through the function is activated.●ON/OFF switch setting Movethecursortothe[SWITCH]item,calltheswitchsetupscreenbypushingtheRTNbutton,andselecttheswitchandONdirection.(For a description of the setting method, see [Switch Setting Method] at the back of this manual.)*Always on when [--].●Master channel setting1.Movethecursortothe[FUNCTION.H/W]itemof[MASTER]andpushtheRTNbuttontoswitchtothedatainputmode. SelectthefunctionbyscrollingtheeditdialandpushtheRTNbutton.2.Whenyouwanttolinkthismixingwithothermixes,movethecursortothe[LINK]itemandpushtheRTNbuttontoswitchtothedatainputmode. Setthelinkmodeto[+]or[-]byscrollingtheeditdialandpushtheRTNbutton.*Check the direction by actual operation.*Master channel control can be set to simple operating amount of sticks and VR which do not include ATV, AFR, D/R, and mixing setting. In this case, the switch setup screen is displayed by pushing the RTN button with "H/W" selected by function selection. Select master channel side control. (To terminate the "H/W" selection, select the [--] display and push the RTN button.●Slave channel setting1.Movethecursortothe[FUNCTION.H/W]itemof[SLAVE]andpushtheRTNbuttontoswitchtothedatainputmode. SelectthefunctionbyscrollingtheeditdialandpushtheRTNbutton.2.Whenyouwanttolinkthismixwithothermixes,movethecursortothe[LINK]itemandpushtheRTNbuttontoswitchtothedatainputmode. Setthelinkmodeto[+]or[-]byscrollingtheeditdialandpushtheRTNbutton.*Check the direction by actual operation.●Servospeedsetting(For a description of the setting method, see the description at the back of this manual.)●Switchselection(For a description of the switch setting method, see the description at the back of this manual.)●Finetuningtrimsetting(For a description of the setting method, see the description at the back of this manual.)●Linksetting●MasterCH●SlaveCH●Trimmodesetting●SlaveCHAFRmode●ON/OFF●MixON/OFFdelay

101<Model Menu (Common Functions)>●Offset mode settingOffset mode is function which allows simultaneous offset control of up 4 slave functions per circuit.1.Use[MODE]settingtoselecttheprogrammixingoparationmode.[MIXING]isthenormalmixingmodeand[OFFSET]istheoffsetmode.2.Movethecursorto[INHIBIT]ofthemixingNo.settotheoffsetmodeandpushtheRTNbutton.Thesetupscreenisdisplayed.3.PresstheS1button.Page5/5isdisplayed.4.Movethecursortothe[STATUS]itemandswitchtothedatainputmodebypushingtheRTNbutton.5.Turnthedialtotheleftandrightuntil[ACT]blinks,andthenpushtheRTNbutton.Todeactivatethefunction,switchto[INH].●ON/OFF switch selection Movethecursortothepage5/5[SWITCH]item,calltheswitchsetupscreenbypushingtheRTNbutton,andthenselecttheswitchandONdirection.(Foradetaileddescriptionoftheselectionmethod,see[SwitchSelectionMethod]atthebackoftheinstructionmanual.)●Slave No. selection SettingoftheslaveNo.from1to4atpages1/5~4/5isdisplayed.WhentheS1buttonispushed,thedisplayedslaveNo.isswitched.●Slave function setting Movethecursortothe[FUNCTION]itemandswitchtothedatainputmodebypushingtheRTNbutton.SelectthefunctionbyscrollingthedialandthenpushtheRTNbutton.●Offset rate settingThe function operation offset amount when the mixing switch is ON and OFF can be set independently.1.Movethecursortothe[ON]or[OFF]itemandswitchtothedatainputmodebypushingtheRTNbutton.2.TurnthedialtotheleftandrightandsettheoffsetratewhentheswitchisONorOFF.Initialsetting:0%Settingrange:-300%~+300%3.Aftersetting,switchtothecursormovemodebypushingtheRTNbutton.*At adjustment, the offset rate is reset to the initial value by pushing the RTN button for 1 second.●Trim mode ON/OFF setting1.Whenchangingthetrimmode,movethecursortothe[TRIM]itemandpushtheRTNbuttontoswitchtothedatainputmode. SelectON/OFFbyscrollingtheeditdialandsettheselectionbypushingtheRTNbutton.*When mixing includes master side trim, select [ON] and when mixing does not include master trim, select [OFF].*Effective when a function is set at the master channel.●Slave channel AFR mode setting (STK-STK)1.Movethecursortothe[STK-STK]item,selectthemodebyscrollingtheeditdial,andchangethemodebypushingtheRTNbutton.*When link is set at the slave side, and you want to add AFR (D/R) to the mixing rate, select [ON].*This is effective when the linkage is the same, but the travels are substantially different.●Mixing curve setting(For a description of the curve setting method, see the description at the back of this manual.)●Fine tuning trim settingOperation control [CTRL], operation mode [MODE], and rate [RATE] adjustment is possible by [FINE TUNING] item.(For a description of the ne tuning trim setting method, see the description at the back of this manual.)●Servo speed settingAdjustment is possible with the [SPEED] item.(For a description of the servo speed setting method, see the description at the back of this manual).●Mixing ON/OFF delay settingDelay time at mix ON [START] and delay time at mix OFF [STOP] adjustment is possible by [DELAY] item.*This function is inactive when a mixing switch is not set.1.Movethe[START]or[STOP]itemandpushtheRTNbuttontoswitchtothedatainputmode.2.Adjustthedelaytimebyscrollingtheeditdial. Initialvalue:0.0sec Adjustmentrange:0~4sec(When the RTN button is pushed for 1 second, the delay time is reset to the initial value.) PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.

102 <Model Menu (Common Functions)>●Fine tuning trim settingOperation control [CTRL], operation mode [MODE], and rate [RATE] adjustment is possible by [FINE TUNING] item.(For a description of the ne tuning trim setting method, refer to [Fine tuning trim setting] at the back of this manual.)●Operation mode settingThe operation mode when the switch was operated is selected. Normal mode [NORM] or timer mode [TIME] can be selected.[Normal mode]After the switch is set to ON, mixing is turned ON after the time set by start delay ([START]) has elapsed. Similarly, after the switch was set to OFF, mixing is turned OFF after the time set by stop delay ([STOP]) has elapsed.[Timer mode]After the switch was set to ON, mixing is turned ON after the time set by start delay ([START]) has elapsed. Mixing is automatically turned OFF after the time set by stop delay ([STOP]) has elapsed. Examples of use are jet plane and scale model retractable landing gear and cover linked mixing, etc. ●Servo speed settingThe speed at function operation can be adjusted. (For a description of the setting method, refer to [Servo speed setting] at the back of the instruction manual.)●Delay settingMixing operation at mixing switch ON ([START]) and OFF ([STOP]) can be delayed by [DELAY] item.(When switch is set.)1.Movethecursortothe[START]or[STOP]itemandswitchtothedatainputmodebypushingtheRTNbutton.2.TurnthedialtotheleftandrightandsetthemixingoperationdelaytimeatswitchONorOFF.Initialsetting:0secSettingrange:0sec~35sec3.Afteradjustment,switchtothecursormovemodebypushingtheRTNbutton.*At adjustment, the delay time can be reset to the initial value by pushing the RTN button for 1 second.

103<Model Menu (Common Functions)>S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>GYRO [Correspondingmodeltype]:Multicopter/Airplane/glider,generalThis function is used when a GYA Series gyro is used to stabilize the aircraft's attitude. The sensitivity and operation mode (Normal mode/GY mode) can be switched with a switch.●Threerates(Rate1/Rate2/Rate3)canbeswitched.●Upto3axes(Gyro/Gyro2/Gyro3)canbesimultaneouslycontrolled.*Initial setting does not assign a sensitivity channel. Use the Function menu of the Linkage Menu to assign the sensitivity channel (Gyro/Gyro2/Gyro3) used to a vacant channel beforehand. Set [Control] and [Trim] other than Function to [--].●Theoperationmode(AVCS/NOR)andsensitivityofthe3axiscontrolledbyGyro/Gyro2/Gyro3canbeset.●Group/singlemodeswitching(For more information, see the description at the back of this manual.)●Threerates(Rate1/Rate2/Rate3)canbeused. Movethecursortothe[RATE]itemandpushtheRTNbuttontoswitchtothedatainputmode.Adjusttheratebyscrollingtheeditdial.●Whenusingthisfunction, movethecursortothe[ACT]itemandpushtheRTNbuttontoswitchtothedatainputmode.TurntheeditdialtotheleftandpushtheRTNbutton.●WhenaFutabaGYAgyroisused,when[GY]typeisselected,thesensitivitysetvalueisdirectlyreadinboththeAVCSandNORMmodes.●Whensettingaswitch,movethecursortotheSWITCHitemandpresstheRTNbuttontocalltheselectionscreen,andthenselecttheswitchandsetitsONdirection. (Foradescriptionoftheswitchselectionmethod,seethedescriptionattheendofthismanual.)(Currently selected condition name)●Select[GYRO] at themodelmenuandcallthesetupscreenshownbelowbypushingtheRTNbutton.Scrolling●Movingcursor●Selectingmode●Adjustingvalue●Pushthe S1 buttontocallnextpage.

104 <Data>This section describes the functions often used at the function setup screen. Refer to it when setting each function.Operations related to ight conditionsCOMMON OPERATIONS USED IN FUNCTION SETUP SCREENGroup/single mode switching (GROUP/SINGLE)When setting multiple flight conditions, linking the setting contents with all conditions (group mode) or setting independently (single mode) can be selected. The mode can be changed at the [GROUP] item on each setup screen.[Group/single mode switching]1. Use the edit dial to move the cursor (reverse-will display) to the [GROUP] item on the setup screen and push the RTN button to switch to the data input mode.2. Turn the edit dial to the left until switch [SINGLE] starts to blink.*At this point, the mode has still not been changed.*When changing from [SINGLE] to [GROUP], turn the edit dial to the right.3. Change the mode by pushing the RTN button.●Group mode (GROUP) The same setting contents are set to all the ight conditions.●Single mode (SINGLE) Set this mode when the setting contents are not linked with other conditions.Condition delay settingUnnecessary fuselage motion generated when there are sudden changes in the servo position and variations in the operating time between channels can be suppressed by using the condition delay function of the condition select function [COND. SELECT].When the delay function is set at the switching destination condition, a delay corresponding to that amount is applied and the related functions change smoothly.[Setting method] *At the condition delay setup screen [COND.DELAY], move the cursor to the [DELAY] item of the channel you want to set and perform the following settings:1. Switch to the condition you want to set and push the RTN button to switch to the data input mode.2. Set the delay by turning the edit dial. Initial value: 0 Adjustment range: 0~27 (maximum delay)(When the RTN button is pushed for 1 second, the delay is reset to the initial value.)3. Push the RTN button to end adjustment and return to the cursor move mode.

105<Data>Operations related to ne tuning VR●VR selection ●Rate adjustment(Fine tuning VR operation position)●Operation mode selection*The operation modes which can be selected depend on the function.[Fine tuning VR operation mode][LIN.] Mixing rate 0% at center of VR. When the VR is turned clockwise and counterclockwise, the mixing rate increases and decreases, respectively.[ATL+] Mixing rate 0% at left end of VR. When the VR is turned, the mixing rate increases.[ATL-] Mixing rate 0% at right end of VR. When the VR is turned, the mixing rate increases.[SYM.] When the VR is turned to the left or right of the neutral position, the mixing rate increases.[Setting method]1. Control selection Use the edit dial to move the cursor (reverse-will display) to the [CTRL] item and push the RTN button to call the selection screen. Move to the control you want to set by turning the edit dial to the left or right and push the RTN button.2. Mode selection Use the edit dial to move the cursor to the [MODE] item and push the RTN button to switch to the data input mode. Turn the edit dial to the left or right and switch to the operation mode ([LIN.], [ATL+], [ATL-], or [SYM.]) corresponding to the set control and push the RTN button.3. Rate adjustment Move the cursor to the [RATE] item and push the RTN button to switch to the data input mode. Turn the edit dial to the left or right and set the rate. Initial value: 0% Adjustment range: -100%~+100%(When the RTN button is pushed for 1 second, the rate is reset to the initial value.) Push the RTN button to end adjustment and return to the cursor move mode.

106 <Data>Operations related to servo speedServo speed settingThe servo speed at each function operation (including flight condition switching) can be adjusted. The servos operate smoothly at a fixed speed corresponding to the set speed. The operating speed (IN side) and return speed (OUT side) can be set individually.Switch the operation mode according to the set function. "SYM." mode: Used with ailerons and other self neutral functions. "LIN." mode: Used with functions which hold the operation position of the throttle and switch channel, etc.[Setting method]1. Use the edit dial to move the cursor (reverse-will display) to the [MODE] item and push the RTN button to switch to the data input mode. Turn the edit dial to the left or right and switch to the operation mode ("SYM." or "LIN.") corresponding to the set function and push the RTN button.2. Move the cursor to the direction ([IN] or [OUT]) item you want to set and push the RTN button to switch to the data input mode. Turn the edit dial to the left or right and set the speed. Initial value: 0 Adjustment range: 0~27 (maximum delay)(When the RTN button is pushed for 1 second, the servo speed is reset to the initial value.) Push the RTN button to end adjustment and return to the edit mode.

107<Data>Curve setting operationThis section describes the setting procedure of curves which are used with the AFR function and each mixing function.Curve type selectionThree types of curves (EXP1, EXP2 and POINT) can be selected.Curve type selection1. Use the edit dial to move the cursor (reverse-will display) to the [MODE] item and push the RTN button to switch to the data input mode.2. Display the curve you want to use by turning the edit dial to the left or right.*The curve type blinks.3. When the RTN button is pushed, the curve type is changed. (Operate the edit dial or S1 button to stop the change.) [EXP1]: EXP1 curve [EXP2]: EXP2 curve [POINT]: point curveSetting by curve typeWhen the curve type is selected as described above, adjustment items corresponding to the curve type appear on the screen. Adjust each curve as described below.B], [EXP A], or [EXP B] setting item and push the RTN button to switch to the data input mode.2. Set the rate by turning the edit dial to the left or right. Initial value: +100.0% (rate)/+0.0% (EXP rate) *Initial value differs depending on function. Adjustment range: -200.0~+200.0% (rate)/-100.0~+100.0% (EXP rate)(When the RTN button is pushed for 1 second, the rate is reset to the initial value.) Push the RTN button to end adjustment and return to the cursor move mode.[Offsetting the curve horizontally in the vertical direction]1. Use the edit dial to move the cursor (reverse-will display) to the [OFFSET] setting item and push the RTN button to switch to the data input mode.2. Move the curve in the vertical direction by turning the edit dial to the left or right. Initial value: +0.0%(When the RTN button is pushed for 1 second, the rate is reset to the initial value.) Push the RTN button to end adjustment and return to the cursor move mode.EXP1/EXP2 curve adjustment(EXP1 curve)Using the EXP1 curve is effective in smoothing starting of the ailerons, elevator, rudder, etc.(EXP2 curve)Using the EXP2 curve is effective in engine rise and other engine control.The curve left and right rates ([RATE A], [RATE B]) and EXP curve rate ([EXP A], [EXP B]) can be adjusted individually. ([EXP] for EXP2)The curve can also be offset horizontally ([OFFSET]) in the vertical direction.[Rate setting]1. Use the edit dial to move the cursor (reverse-will display) to the [RATE A], [RATE

108 <Data>Point curve (POINT) adjustment(Point)Up to 11 or 17 points curve can be used. (differs with function) Initial point number: 9 points (17 points curve), 11 points (11 points curve)*The set points can be freely increased, decreased, and offset.[Rate adjustment of each point]1. Use the edit dial to move the cursor (reverse-display) to the [POINT] or [RATE] item and push the RTN button to switch to the curve setting mode.*It is changed from the reverse-display to the square box display.*In this mode, push the RTN button to switch the [POINT] item and [RATE] item alternately.2. Move the cursor (square box) to the [POINT] item by pushing the RTN button.3. Turn the edit dial to the left or right and select the point whose rate you want to set.*The mark on the curve shows the currently selected point. The mark on the curve shows the currently deleted point.4. Move the cursor (square box) to the [RATE] item by pushing the RTN button and set the rate by turning the edit dial to the left or right. Repeat steps 2 through 5 and adjust the curve. Push the S1 button to end adjustment and return to the cursor move mode.[Point addition]1. In the curve setting mode, push the RTN button to move the cursor to the [POINT] item and turn the edit dial to the left or right and move the cursor on the curve to the position (mark ) you want to add.2. When the RTN button is pushed for 1 second, the point is added.[Point deletion]1. In the curve setting mode, push the RTN button to move the cursor to the [POINT] item and turn the edit dial to the left or right and move the cursor on the curve to the position (mark ) you want to delete.2. When the RTN button is pushed for 1 second, the point is deleted.[Offsetting the curve horizontally in the vertical direction]1. Use the edit dial to move the cursor (reverse-will display) to the [OFFSET] item.2. Move the curve in the vertical direction by turning the edit dial to the left or right. Initial value: +0.0%(When the RTN button is pushed for 1 second, the curve is reset to the initial value.) Push the RTN button to end adjustment and return to the cursor move mode.

109<Data>Switch selection methodThe various functions used in the FMT-03 can be selected by switch. The switch (including when stick, trim lever, or VR are used as a switch) setting method is common to all functions.Switch selectionWhen a switch is selected at a mixing function, etc., the selection screen shown below is called.(Switch selection screen example)When switch was selectedWhen switch was selected, ON/OFF position setting is also performed.*The ON/OFF setting state of each position is displayed.1. When you want to change the ON/OFF setting, use the edit dial to move the cursor and push the RTN button to switch to the data input mode. Switch the ON/Off display by turning the edit dial to the left or right.*ON/OFF display blinks.2. When the EDIT button is pressed, the ON/OFF setting is changed. (Operate the edit dial or S1 button to stop the change.)3. To return to the preceeding screen, move the cursor to the [ON/OFF] at the top of the screen and push the RTN button.When stick, trim lever, or knob selectedWhen a stick, trim lever, or knob is used as a switch, four operation modes can be selected by the following mode and type combination:1. When you want to change the mode, move the cursor to [MODE] and push the RTN button to switch to the data input mode. Switch the display to the mode you want to change by turning the edit dial to the left or right and then make the change by pushing the RTN button. ●Mode: [LINEAR]/[SYMMETRY]*Set the ON/Off point by the method described on the next page.Switch selection1. Use the edit dial to move the cursor (highlights) to the switch you want to select and push the RTN button.*The switch blinks.2. To return to the preceeding screen, move the cursor to the [HARDWARE SEL.] at the top of the screen and push the RTN button. Or, move the cursor to the [ON/OFF] and call the ON/OFF position setting screen by pushing the RTN button.Alternate mode setting ●Mode: [NORMAL]/[ALTERNATE]1. Move the cursor to the [ALTERNATE] item and push the RTN button to switch to the data input mode. 2. Change to the mode you want to set by turning the edit dial to the left or right.*The mode display blinks.3. Push the RTN button. (Operate the edit dial or S1 button to stop the change.)4. To return to the preceeding screen, move the cursor to the [ON/OFF] at the top of the screen and push the RTN button.

110 <Data>Operation modesThe operation modes when stick, trim lever, or knob are selected is described below. Linear modeThis mode sets ON/OFF at the left or right (up or down) with the set point as the reference. Symmetrical modeLeft and right (up and down) operations are symmetrical about the neutral position. For instance, when you want to switch DR1 with the aileron stick, when the stick is moved to the left or right, DR1 can be turned on at the same left and right position.Shifting the ON/Off pointThe ON/OFF point can be shifted. ON/OFF at a free position can be changed.●Black range: OFF range●White range: ON range[Setting method]1. First, use the edit dial to move the cursor to the [POSITION] item.2. Move the stick, trim lever, or knob to the point you want to change and push the RTN button. The point is shifted.3. To return to the preceeding screen, move the cursor to the [ON/OFF] at the top of the screen and push the RTN button.

111<Data>Logic mode AND: When both switches are ON, the condition is ON. OR: When either switches is ON, the condition is ON. EOR: When the two switches are in different states, the condition is ON.Switch mode selection1. Move the cursor to the [MODE] item and push the RTN button to switch to the data input mode. 2. Turn the edit dial to the left and select the [LOGIC].*[LOGIC] display blinks.3. Push the RTN button to change to the logic switch mode.(Logic switch setting screen)Swich selection1. Select the switch A and B. (Refer to the description at the previous page.)Logic mode selection1. Move the cursor to the [LOGIC] item and push the RTN button to switch to the data input mode. 2. Turn the edit dial to the left or right and select the logic mode.*The mode display blinks.3. Push the RTN button to change to the logic mode.4. To return to the preceeding screen, move the cursor to the [SWITCH] at the top of the screen and push the RTN button.Logic switch (Condition Select function only)The logic switch function lets you turn operation on and off by combining two switches. For instance, the condition is activated when 2 switches are turned on.

112 <Data>UPDATINGYour Futaba FMT-03 transmitter programming can be updated easily online. When functions are added or improved, the update le can be downloaded from our website. Copy the update les to the SD card and then use the following procedure to update the program.Check our web site for the FAQ regarding updating for more information.Updating procedureNote: If the battery fully discharges during program updating, updating will fail. When the remaining battery capacity is 50% or less, always recharge the battery before updating.Note: The model data in the transmitter can be used unchanged after updating, but to be safe, back up the model data before updating.1. Copy update files to a SD card. Typical structure of folders of the card for update are following.2. Attach the SD card into the SD slot of the FMT-03.3. Press the Home/Exit switch and turn on the power switch, and FMT-03 should begin to update.4. When updating is complete, the screen shown below appears. 5. Turn off the power switch. After the monitor LED goes off, switch the update switch in the down direction. After the updating above has been completed, turn on the power and then check the system program version at the system menu information screen.6. If writing goes wrong, the following error message will come out."LOW BATTERY""UPDATE FILE NOT FOUND""BROKEN FILE""WRITE ERROR" Removable disk (E:)② It inserts until it locks micro SD card into SD card slot.*It is releasable if a card is pushed once again.*Don't mistake the direction that the micro SD card is inserted.① Open the battery cover. (Minus driver is used.)SD card slot

113＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.AIRPLANE/GLIDER/HELICOPTER FUNCTIONSFMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of airplane, glider and helicopter.But, FMT-03 is also equipped with the function of the airplane, glider and helicopter. It's indicated on a page after this by reference.

114 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.●Selectthe[MODELMENU]andreturnto the homescreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.MODEL MENU (AIRPLANE/GLIDER FUNCTIONS)The dedicated mixes, etc. usable when airplane or glider model type is selected are displayed in this Model Menu functions section. First use the Model Type function of the Linkage Menu to preset the model type, wing type, and tail type matched to the fuselage used. Other settings reset the data used in mixing function, etc.These dedicated mixes can be set for each flight condition, as required. When you want to use the system by switching the settings for each condition by switch or stick position, use the Condition Select function to add ight conditions. (Up to 8 conditions can be used)Note:TheFMT-03isdesignedsothattheairplaneandglidermodeltypescanhandleaircraftofthesamewingtype.Thefunctionscommontoairplanesandgliders,exceptsomededicatedfunctions,aresummarizedwithoutregardtothemodeltype.Thesettingitemsaredifferent,dependingonthenumberofservos,etc.accordingtothewingtypeused.Thesetupscreensintheinstructionmanualaretypicalexamples.Model Menu functions listAIL DIFFERENTIALThis function adjusts the left and right ailerons. Roll axis correction and ne tuning with a VR are also possible. This is convenient when making settings during ight.[Airplane/glider, 2 ailerons or more]FLAP SETTINGThe aps can be adjusted independently. For a 4 aps model, the camber aps can be mixed with the brake aps. [Airplane/glider, 2 aps or more]AIL to CAMBERFLPThis mix operates the camber flaps in the aileron mode. It improves the operation characteristic of the roll axis. [Airplane/glider, 2 ailerons + 2 aps or more]AIL to BRAKEFLPThis mix operates the brake aps in the aileron mode. It improves the operation characteristic of the roll axis. [Airplane/glider, 4 aps or more]AIL to RUDThis mix is used when you want to operate the rudder at aileron operation. Banking at a shallow bank angle is possible. [Airplane/glider, general]AIRBRAKE to ELEThis mix is used to correct operation of the airbrakes (spoilers) when landing. [Airplane/glider, general](Model Menu screen example)*The Model Menu screen depends on the model type. This screen is for model type 4AIL+4FLP.●Selectthe [MODEL] atthehomescreenandcallthemodelmenushownbelowbypushingtheRTNbutton.●UsetheeditdialtoselectthefunctionyouwanttosetandcallthesetupscreenbypushingtheRTNbutton.S1<Editdial>●Pushthe S1 buttontocallnextpage. Scrolling●Movingcursor

115＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.AIL 3(Chip Aileron) AIL 4(Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)FLP 2(Camber Flap)FLP 1(Camber Flap)ELEVATOR(ELEVATOR 2)V-TAIL AILVATORFLP 3AIR BRAKE(Brake Flap)FLP 4(Brake Flap) RUDDER 2 WingletRUDDER 1RUDDER (RUDDER 2) Wingletat Flying wing at Flying wing( ) ( )ELEVATOR ELEVATOR 2(AILERON 5)(AILERON 6)RUD to AILThis mix is used to correct roll maneuvers, knife edge, etc. of stunt planes. [Airplane/glider, general]CAMBER MixThis mix adjusts the camber and corrects the elevators. [Airplane/glider, 2 ailerons or more]ELE to CAMBERThis mix is used when you want to the mix camber aps with elevator operation. Lifting force can be increased at elevators up. [Airplane/glider, 2 ailerons or more]CAMBERFLP to ELEThis mix is used to correct for attitude changes when the camber aps are being used. [Airplane/glider, 2 ailerons + 1 ap or more]BUTTERFLY (Crow)This function is used when powerful brake operation is necessary. [Glider, 2 ailerons or more]TRIM MIX 1/2The ailerons, elevators, and flaps trim offset rate can be called by switch or condition selection. [Glider, 2 ailerons or more]AIRBRAKEThis function is used when airbrakes are necessary when landing or when diving, etc. during ight. (Airplane, general)GYROThis is a dedicated mix when a GYA Series gyro is used. [Airplane/glider, general]V-TAILThis function adjusts the elevators and rudder of V-tail models. [Airplane/glider, V-tail specications]AILEVATORThis function adjusts the elevators and ailerons of models with elevator specications. [Airplane/glider, elevator specications]WINGLETThis function adjusts the left and right rudders of winglet models. [Airplane/glider, winglet specications]MOTORThe operation speed when the motor of F5B and other EP gliders is started by switch can be set. [EP glider, general]RUD to ELEThis function is used to correct roll maneuvers, knife edge, etc. of stunt planes. [Airplane, general]SNAP ROLLThis function selects the snap roll switch and adjusts the steering angle of each rudder. Servo speed can also be adjusted. [Airplane general]

116 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.Servo connection by Airplane/glider typeThe FMT-03 transmitter channels are automatically assigned for optimal combination according to the type selected with the Model Type function of the Linkage Menu. The channel assignment (initial setting) for airplane/glider type is shown below. Connect the receiver and servos to match the type used.*The set channels can be checked at the Function screen of the Linkage Menu. The channel assignments can also be changed. For more information, read the description of the Function menu.Airplane/glider/motor glider●Airplane and V tailRXCH1AIL 2AIL 2AIL+1FLAP 2AIL+2FLAPAirplane Glider Airplane Glider Airplane Glider Airplane GliderEP EP EP EP1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator3 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX74Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder5Gear AUX6 AUX6 Gear AUX6 AUX6 Gear AUX6 AUX6 Aileron2 Aileron2 Aileron26 Airbrake Airbrake Airbrake Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Flap Flap Flap7 AUX5 AUX5 AUX5 AUX5 AUX5 AUX5 Flap Flap Flap Flap2 Flap2 Flap28AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX5 AUX5 AUX5 Gear AUX6 AUX69AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX4 AUX4 AUX4 AUX5 AUX5 AUX510 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX3 AUX3 AUX3 AUX4 AUX4 AUX411 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX2 AUX2 AUX2 AUX3 AUX3 AUX312 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX2 AUX2 AUX213 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX114 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX115 AUX1 AUX1 AUX1 AUX1 Buttery Buttery AUX1 Buttery Buttery AUX1 Buttery Buttery16 AUX1 AUX1 AUX1 Camber Camber Camber Camber Camber Camber Camber Camber CamberDG1 SW SW SW SW SW SW SW SW SW SW SW SWDG2 SW SW SW SW SW SW SW SW SW SW SW SWRXCH2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator3 Throttle Rudder Rudder Throttle Rudder Rudder Throttle Rudder Rudder4Rudder Aileron2 Aileron2 Rudder Aileron2 Aileron2 Rudder Aileron2 Aileron25Gear Flap Flap Gear Aileron3 Aileron3 Gear Aileron3 Aileron36 Aileron2 Flap2 Flap2 Aileron2 Aileron4 Aileron4 Aileron2 Aileron4 Aileron47 Flap Flap3 Flap3 Aileron3 FlapFlapAileron3 FlapFlap8Flap2 Flap4 Flap4Aileron4 Flap2 Flap2 Aileron4 Flap2 Flap29Flap3 Motor AUX7Flap MotorAUX7Flap Flap3 Flap310 Flap4 AUX6 AUX6 Flap2 AUX6 AUX6Flap2 Flap4 Flap411 AUX5 AUX5 AUX5 AUX5 AUX5 AUX5 Flap3 Motor AUX712 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 Flap4 AUX6 AUX613 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX5 AUX5 AUX514 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX4 AUX4 AUX415 AUX1 Buttery Buttery AUX1 Buttery Buttery AUX3 Buttery Buttery16 Camber Camber Camber Camber Camber Camber Camber Camber CamberDG1 SW SW SW SW SW SW SW SW SWDG2 SW SW SW SW SW SW SW SW SWFASSTest 12CHFASSTest 18CHThe output CH of each systemFASSTest 12CHFASSTest 18CHThe output CH of each system

117＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.RXCH1AIL 2AIL 2AIL+1FLAP 2AIL+2FLAPAirplane Glider Airplane Glider Airplane Glider Airplane GliderEP EP EP EP1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator3 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX74Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder5Gear AUX6 AUX6 Gear AUX6 AUX6 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator26 Airbrake Airbrake Airbrake Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron27 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Flap Flap Flap Flap Flap Flap8AUX5 AUX5 AUX5 AUX5 AUX5 AUX5 Gear AUX6 AUX6 Flap2 Flap2 Flap29AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX5 AUX5 AUX5 Gear AUX6 AUX610 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX4 AUX4 AUX4 AUX5 AUX5 AUX511 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX3 AUX3 AUX3 AUX4 AUX4 AUX412 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX2 AUX2 AUX2 AUX3 AUX3 AUX313 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX2 AUX2 AUX214 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX115 AUX1 AUX1 AUX1 AUX1 Buttery Buttery AUX1 Buttery Buttery AUX1 Buttery Buttery16 AUX1 AUX1 AUX1 Camber Camber Camber Camber Camber Camber Camber Camber CamberDG1 SW SW SW SW SW SW SW SW SW SW SW SWDG2 SW SW SW SW SW SW SW SW SW SW SW SWRXCH2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator3 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX74Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder5Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator2 Elevator26 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron27 Flap Flap Flap Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Aileron38Flap2 Flap2 Flap2 Aileron4 Aileron4Aileron4Aileron4 Aileron4Aileron49Flap3 Flap3 Flap3Flap Flap Flap Flap Flap Flap10 Flap4 Flap4 Flap4Flap2 Flap2Flap2Flap2 Flap2 Flap211 Gear AUX6 AUX6 Gear AUX6 AUX6 Flap3 Flap3Flap312 AUX5 AUX5 AUX5 AUX5 AUX5 AUX5 Flap4 Flap4 Flap413 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 Gear AUX6 AUX614 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 AUX5 AUX5 AUX515 AUX2 Buttery Buttery AUX2 Buttery Buttery AUX4 Buttery Buttery16 Camber Camber Camber Camber Camber Camber Camber Camber CamberDG1 SW SW SW SW SW SW SW SW SWDG2 SW SW SW SW SW SW SW SW SW●AilevatorFASSTest 12CHFASSTest 18CHThe output CH of each systemFASSTest 12CHFASSTest 18CHThe output CH of each system

118 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.●Tailless wingRXCH2AIL 2AIL+1FLAP 2AIL+2FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX4 AUX43 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX74Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder5Gear AUX6 AUX6 Gear AUX6 AUX6 Aileron2 Aileron2 Aileron26 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Flap Flap Flap7 AUX5 AUX5 AUX5 Flap Flap Flap Flap2 Flap2 Flap28AUX3 AUX3 AUX3 AUX5 AUX5 AUX5 Gear AUX6 AUX69AUX2 AUX2 AUX2 AUX3 AUX3 AUX3 AUX5 AUX5 AUX510 AUX1 AUX1 AUX1 AUX2 AUX2 AUX2 AUX3 AUX3 AUX311 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX2 AUX2 AUX212 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX113 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX114 AUX1 AUX1 AUX1 AUX1 Buttery Buttery AUX1 Buttery Buttery15 Camber Camber Camber Camber Camber Camber Camber Camber Camber16 Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator ElevatorDG1 SW SW SW SW SW SW SW SW SWDG2 SW SW SW SW SW SW SW SW SWRXCH2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron23 Throttle Motor AUX7 Throttle MotorAUX7Throttle MotorAUX74Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder5Flap Flap Flap Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Aileron36 Flap2 Flap2 Flap2 Aileron4 Aileron4 Aileron4 Aileron4 Aileron4 Aileron47 Flap3 Flap3 Flap3 FlapFlapFlapFlap FlapFlap8Flap4 Flap4 Flap4 Flap2 Flap2 Flap2 Flap2 Flap2 Flap29AUX4 AUX4 AUX4 AUX4 AUX4 AUX4Flap3 Flap3 Flap310 Gear AUX6 AUX6 Gear AUX6 AUX6 Flap4 Flap4 Flap411 AUX5 AUX5 AUX5 AUX5 AUX5 AUX5 AUX4 AUX4 AUX412 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 Gear AUX6 AUX613 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX5 AUX5 AUX514 AUX1 Buttery Buttery AUX1 Buttery Buttery AUX3 Buttery Buttery15 Camber Camber Camber Camber Camber Camber Camber Camber Camber16 Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator ElevatorDG1 SW SW SW SW SW SW SW SW SWDG2 SW SW SW SW SW SW SW SW SWFASSTest 12CHFASSTest 18CHThe output CH of each systemFASSTest 12CHFASSTest 18CHThe output CH of each system

119＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.●Tailless wing Winglet 2RudderRXCH2AIL 2AIL+1FLAP 2AIL+2FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2RUD2 RUD2 RUD2 RUD2 RUD2 RUD2 RUD2 RUD2 RUD23 Throttle Motor AUX7 Throttle Motor AUX7 Throttle Motor AUX74Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder5Gear AUX6 AUX6 Gear AUX6 AUX6 Aileron2 Aileron2 Aileron26 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Flap Flap Flap7 AUX5 AUX5 AUX5 Flap Flap Flap Flap2 Flap2 Flap28AUX3 AUX3 AUX3 AUX5 AUX5 AUX5 Gear AUX6 AUX69AUX2 AUX2 AUX2 AUX3 AUX3 AUX3 AUX5 AUX5 AUX510 AUX1 AUX1 AUX1 AUX2 AUX2 AUX2 AUX3 AUX3 AUX311 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX2 AUX2 AUX212 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX113 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX1 AUX114 AUX1 AUX1 AUX1 AUX1 Buttery Buttery AUX1 Buttery Buttery15 Camber Camber Camber Camber Camber Camber Camber Camber Camber16 Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator ElevatorDG1 SW SW SW SW SW SW SW SW SWDG2 SW SW SW SW SW SW SW SW SWRXCH2AIL+4FLAP 4AIL+2FLAP 4AIL+4FLAPAirplane Glider Airplane Glider Airplane GliderEP EP EP1 Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron Aileron2Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron2 Aileron23 Throttle Motor AUX7 Throttle MotorAUX7Throttle MotorAUX74Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder Rudder5Flap Flap Flap Aileron3 Aileron3 Aileron3 Aileron3 Aileron3 Aileron36 Flap2 Flap2 Flap2 Aileron4 Aileron4 Aileron4 Aileron4 Aileron4 Aileron47 Flap3 Flap3 Flap3 FlapFlapFlapFlap FlapFlap8Flap4 Flap4 Flap4 Flap2 Flap2 Flap2 Flap2 Flap2 Flap29RUD2 RUD2 RUD2 RUD2 RUD2 RUD2Flap3 Flap3 Flap310 Gear AUX6 AUX6 Gear AUX6 AUX6 Flap4 Flap4 Flap411 AUX5 AUX5 AUX5 AUX5 AUX5 AUX5 RUD2 RUD2 RUD212 AUX3 AUX3 AUX3 AUX3 AUX3 AUX3 Gear AUX6 AUX613 AUX2 AUX2 AUX2 AUX2 AUX2 AUX2 AUX5 AUX5 AUX514 AUX1 Buttery Buttery AUX1 Buttery Buttery AUX3 Buttery Buttery15 Camber Camber Camber Camber Camber Camber Camber Camber Camber16 Elevator Elevator Elevator Elevator Elevator Elevator Elevator Elevator ElevatorDG1 SW SW SW SW SW SW SW SW SWDG2 SW SW SW SW SW SW SW SW SW* Output channels differ by each system of a table. When using a system with few channels, there is a wing type which cannot be used. It cannot be used when there is a function required out of the range of the arrow of a gure.FASSTest 12CHFASSTest 18CHThe output CH of each systemFASSTest 12CHFASSTest 18CHThe output CH of each system

120 ＜Model Menu (Airplane/Glider Functions) ＞Reference FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.S1●SelectthefunctionnameandreturntotheprecedingscreenbypushingtheRTNbuttonorpushingtheHome/Exitbutton.<Editdial>AIL 3(Chip Aileron) AIL 4(Chip Aileron)AIL1(Main Aileron) AIL 2(Main Aileron)AIL DIFF. [Airplane/glider,2aileronsormore]The left and right aileron differential can be adjusted independently. The differential rate can also be adjusted according to the flying state by setting a ne tuning VR.●CallstheAFR screendirectlywhenadjustingaileronoperationAFR.●FinetuningVRsetting*The graph is operated by setting a VR, etc.●Group/singlemodeswitching(For more information, refer to the description at the back of this manual.)●Aileronleft/rightadjustment<Wing type: 4 ailerons screen>*The display screen is an example. The actual screen depends on the Model Type.●OveralladjustmentbyRateAandRateB.Setting method●Movethecursortotheaileron(AIL)1~4left(orright)settingitemandpushtheRTNbuttontoswitchtothedatainputmode. Adjusttheaileronangleswhenthestickismovedtotheleft(orright)end. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.*The aileron AFR screen can be directly called from the AIL differential setup screen. ([AIL-AFR] )●WhensettingthefinetuningVR,movethecursortothe"--"itemandpushtheRTNbuttontocalltheselectionscreen,andthenselectthenetuningVR. PushtheRTNbuttontoendadjustmentandreturntothecursormovemode.●Thenetuningratecanbesetbycurve.(Currently selected condition name)●Select[AILDIFF.]atthemodelmenuandcallthesetupscreenshown below by pushingtheRTNbutton.Scrolling●Movingcursor●Selectingmode●Adjustingvalue

Navigation menu

Upload a User Manual

Namespaces

Wiki Guide
HTML
PDF
Info

Views

User Manual
Discussion / Help

Navigation

© 2024 UserManual.wiki | Privacy Policy

Contact Us
DMCA