Futaba FX-20-24G Radio Control User Manual 7 Instruction manual

Download:
Mirror Download [FCC.gov]
Document ID	1876424
Application ID	wkz2X6l2V3Mikl50IKKjpg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.96kB (412038 bits)
Date Submitted	2013-01-09 00:00:00
Date Available	2013-01-09 00:00:00
Creation Date	2012-12-28 03:07:41
Producing Software	PrimoPDF
Document Lastmod	2012-12-28 12:10:25
Document Title	Microsoft Word - 7.Instruction manual.doc
Document Creator	PrimoPDF http://www.primopdf.com
Document Author:	Saegusa

FX-20-2.4G
FX-20
Radio Control
Instruction Manual
INTRODUCTION
Thank you for purchasing a Futaba digital proportional R/C system. In order for you to make the
best use of your system and to use it safely, please read this manual carefully. If you have any
difficulties while using your system, please consult the manual, our online Frequently Asked
Questions (on the web pages referenced below), your hobby dealer.
Owner’s Manual and Additional Technical Help
This manual has been carefully written to be as helpful to you, the new owner, as possible.
There are many pages of setup procedures and examples. However, it need not be your sole
resource of setup guidelines. For example, the back cover includes a quick-start set of
instructions and the Frequently Asked Questions web page referenced below includes this type
of step-by-step setup instructions for a variety of other model types.
Due to potential unforeseen changes in production procedures, the information contained in this
manual is subject to change without notice. No part of this manual may be reproduced in any
form, at any time, without prior permission.
Support and Service: It is recommended to have your Futaba equipment serviced annually
during your hobby’s “off season” to ensure safe operation.
Futaba Corporation
FX-20-2.4G
IN NORTH AMERICA
Please contact Uwe Frank Heinrich to assist you with any questions, problems or
service needs.
Uwe Frank Heinrich
1214 SW 39th Street
Cape Coral, FL 33914
Phone: 239-540-7872
Cell: 239-223-8581
OUTSIDE NORTH AMERICA
Please contact your Futaba importer in your region of the world to assist you with any
questions, problems or service needs.
Please recognize that all information in this manual, and all support availability, is
based upon the systems sold in North America only. Products purchased elsewhere
may vary. Always contact your region’s support center for assistance.
Futaba Corporation
FX-20-2.4G
Federal Communications Commission Interference Statement (for U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void
the user's authority to operate the equipment.
Exposure to Radio Frequency Radiation
To comply with FCC RF exposure compliance requirements, a separation distance of at least
20cm must be maintained between the antenna of this device and all persons.
This device must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Futaba Corporation
FX-20-2.4G
Instruction of the FXFX-2020-2.4G
1.Location
SW-B
LD
SW-E
SW-D
RD
SW-G
SW-A
SW-H
LS
RS
Left Stick
Right Stick
J1
J4
J3
J2
T4
T2
T3
T1
Touch sensor
Power Switch
LCD
Fig. Front view
Charge jack
SD card slot
DSC connector
Fig. side view
Futaba Corporation
FX-20-2.4G
Slider
Fig. Bottom view
Ni-MH battery
Fig. Inside view (Battery box)
2.Charging
2.Charging the battery
1-1. Please confirms the power switch is off.
1-2. Insert the plug of the charger to charging bush of transmitter.
1-3. During the charging, the LED of the charger is on.
The charging time is appx. 15 hours. Please do not charge the battery for 15hours or more.
The overcharge damages the battery.
The battery is 6 cells Ni-MH battery the capacity is 7.2 V/ 1,700mAH.
Futaba Corporation
FX-20-2.4G
３．Operation
３．Operation of the touch sensor
Operation
Contents
Condition
Touch
Short touch
part
S1
Working
At the screen have some pages. The cursor jumps to top of next
(Ex. P-MIX screen)
page
At the screen have Only one(１) The cursor jumps the top of page.
page.
At the input data mode with The setting data is canceled.
blinking the setting data.
RTN
At the moving cursor mode.
Change to the input data mode.
At the input data mode.
Change to the moving cursor mode.
At the input data mode with The data is entered.
blinking the setting data.
Long touch（1 second）
SYS
Home screen,
System menu,
Linkage Menu,
Model menu,
Selecting ON/OFF Switch,
USER NAME,
MODEL NAME,
DISPLAY, INFO,
MODEL SELECT,
MODEL TYPE,
FREQUECY,
DATA RESET,
TIMER,
Selecting Control,
Selecting Function,
SERVO MONITOR
Jump to “System Menu” screen
directly.
Except of above
Jump to “SERVO MONITOR”
screen directly.
LNK
At all screens
Jump to “Linkage Menu” screen
directly.
MDL
At all screens
Jump to “Model Menu” screen
directly.
S1
HOME screen
Key lock On or Off
Except the HOME screen
Jump to HOME screen directly.
RTN
At the input data mode with Entered decision.
blinking the setting data.
At the input data mode without Reset to the initialized value.
blinking the setting data.
Scrolling
Outline
At the moving cursor mode
The cursor is moved.
Futaba Corporation
FX-20-2.4G
of “RTN”
Input data mode
Increment or decrement the data.
Select Yes or No, and so on.
4.Turns
4.Turns on the transmitter
4-1 Power switch is to be on. The red LED is light. LCD displays the bar graph at moment.
4-2 Then, LCD displays the Home screen immediately.
Futaba Corporation
FX-20-2.4G
5． Basic operation of editing
LCD screen is consists of editing button and monitor display. You can go through editing menu
by touch sensor. If you want t o go back to previous menu, you move the cursor to screen title
and touch “RTN”.
6.Home
6.Home screen
You always enter this screen after turning on the power. It is a base screen to edit.
12
11
13
10
1.
2.
3.
4.
5.
6.
7.
User Name
Timer #1
Model Name
Clock icon (Jump to timer screen)
Integrated Timer
Model Timer
Battery Gauge
8.
9.
10.
11.
12.
13.
Mode (MULT / 7CH)
Timer #2
Trim Indicator
Model Type Icon
Memory Card Icon (at detected card)
RF Transmit
Futaba Corporation
FX-20-2.4G
7.Linkage
7.Linkage menu
The linkage menu sets the primary data of the each model. These data are common to every
flight condition.
If you touch “LNK” of the touch sensor over 1 second, you can get into the linkage menu screen.
8.Model
8.Model Menu
The model menu sets the data of mixer. These data of each flight condition can be set.
If you touch “MDL” of the touch sensor over 1 second, you can get into model menu screen.
9.System
9.System Menu
The system menu sets the transmitter setting data. For example, display contrast, stick mode.
If you touch “SYS” of the touch sensor over 1 second, you can get into system menu screen
Futaba Corporation
FX-20-2.4G
Specification
FX-20-2.4G SPECIFICATIONS
1 Radio Characteristics
Engineering standard
Part 15.247 FCC (U.S.)
RF power output
Modulation
Communication scheme
Frequency band
Channel
Data barer rate
Frequency control
50mW
Direct-Sequence Spread-Spectrum
Single communication
2405.376MHz - 2477.056MHz (general mode)
2407.424MHz - 2450.432MHz (France mode)
36 or 22
136 kbps
Crystal controlled frequency synthesizer
Antenna
1/2λ Pencil type antenna 1.5dBi (MAX)
2 Radio communication control
Error checking
CRC-CCITT
3 Terminal interface
Physical interface
none
4 Power Supplying
Supply voltage
Current consumption
7.2V DC
250 mA
5 Environmental
Operating temperature
-10 to +45 ℃
Storage temperature
-20 to +60 ℃
6 Miscellaneous
Indicator
Frequency setting
Case
Outer dimensions
Weight
LCD display, 2 LED
programmable
Plastic
220(W)×210(D)×64(H) mm
Approx. 740g
Futaba Corporation
10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Saegusa
Create Date                     : 2012:12:28 03:07:41Z
Modify Date                     : 2012:12:28 12:10:25+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : PrimoPDF
Creator Tool                    : PrimoPDF http://www.primopdf.com
Metadata Date                   : 2012:12:28 12:10:25+08:00
Document ID                     : 3e50b030-52f7-11e2-0000-9775c6158571
Instance ID                     : uuid:3a7eb530-9e4c-4be8-840e-975920e7b596
Format                          : application/pdf
Title                           : Microsoft Word - 7.Instruction manual.doc
Creator                         : Saegusa
Page Count                      : 10

EXIF Metadata provided by EXIF.tools