G4S Technology S840 Access control proximity reader User Manual S840

G4S Technology Limited Access control proximity reader S840

S840 user manual

Installation and User Instructions for S840 ReadersYou should find that thebackplate has holes forconnection to moststandard electricalbackboxes.With the backplate off (see above), mountthe backplate adjacent to the opening edgeof the door and at a convenient height. Feedthe required cables through the backplate:The cable from the controller.The cable from the heater, if used (mustbe a separate cable).A cable from a Remote Interface Module(RIM), if used. A RIM can reduce cablelengths to door furniture.!!!2The optional heater kit maintains the reader atthe correct temperature when mounted outside.With the backplate off, remove the backing paperfrom the two elements, then stick them to theinner sides of the reader. The heaters must beconnected to a 24V AC supply (min 25VA).When mounting outside, the two-part gasket kitmust be fitted:a) Remove the backplate from the reader byreleasing the two securing screws.b) Remove the cutouts and backing paperfrom the two gaskets, then stick them to thebackplate as shown.Outer gasketInnergasketBackplatesecuring screwsBackplate1Fit the Weatherproofing KitMount the BackplateEnsure no jumper is fitted across LK2 (TEST). If a jumper is provided, park it across one pin only. LK4(AUDIO KB FB) - set to 1 for sound on and 0 for sound off. LK1 (LED BR) - set to H position.3Reader LinksThe S840 is a contactless smart-card reader withkeypad, which uses p. The S840 is able to read HID formatcards.20mA current loop seudo-randomcommunications ®
SpecificationsInput voltage: 9-14Vdc.Input current (excl. heater): 110mA @ nom. 12Vdc.Operating temperature: -13 to 158 F (-25 to 70 C)without heater.Operating humidity: 15 to 90%, non-condensing.Maximum read range: 6" (150mm).Approvals: EN50133, R&TTE, IP656.°°5Using the Reader0VConnect shield at controllerend only (attach to case).RX+RX-TX+TX-12V ReaderTwisted pairs (useBelden 9503 cable)Controllerconnections(20mA currentloop)The I/O terminal is forconnection to a RIM (seethe RIM Instructions).On completion, re-securethe reader to the backplate.0VTX+Do not useTX-I/0RX+RX-+12V4Reader Connections9600-0347. Installation and User Instructions for S840 Readers,Issue 1.0x2 7th January 2004. AMAG Technology Ltd, 2004.All trademarks acknowledged. HID is a registered trademark of HIDCorporation.FCC Notice: This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This devicemay not cause harmful interference, and (2) this device must acceptany interference received, including interference that may causeundesired operation.Any unauthorized modification to this device may void the authority ofthe user to operate it.©Present the card face-on to the reader until you hear "bleep". Cards can be presented in rapidsuccession; there is no need to wait for the green or red LED to extinguish efore presenting another.abIf the reader has been enabled for user-code mode at the controller, you can gain access by pressingthe # key, entering your card number, then pressing the * key.If the amber LED flashes, enter your PIN. If you make amistake, the red LED is lit for a moment, then the flashingamber prompts you to try again.These auxiliary LED indicators can be configured tooperate in conjunction with conditional commands.When this LED is lit, the lock is released and you mayopen the door.Green (accessgranted) LEDRed (accessdenied) LEDFlashing amber(PIN) LEDAlarm LEDSwitch LEDThis is lit if you do not have access rights to gain entry, orif the reader could not read your card (in this case, movethe card away, then present it again).About the Reader LEDs}

Navigation menu