G4S Technology S840 Access control proximity reader User Manual S840

Download:
Mirror Download [FCC.gov]
Document ID	394750
Application ID	gIRU6d5OJG1oJc45Uz4NHw==
Document Description	S840 user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.01kB (200079 bits)
Date Submitted	2004-02-06 00:00:00
Date Available	2004-02-13 00:00:00
Creation Date	2004-01-09 09:32:43
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2004-02-06 10:25:01
Document Title	C:\Group4\Hardware manuals\Reader Instructions\s84x\s840 Installation Instructions.eps
Document Creator	CorelDRAW(TM) Classic

Installation and User Instructions for S840 Readers
The S840 is a contactless smart-card reader with
keypad, which uses 20mA current loop pseudo-random
communications. The S840 is able to read HID® format
cards.
Fit the Weatherproofing Kit
When mounting outside, the two-part gasket kit
must be fitted:
a) Remove the backplate from the reader by
releasing the two securing screws.
b) Remove the cutouts and backing paper
from the two gaskets, then stick them to the
backplate as shown.
The optional heater kit maintains the reader at
the correct temperature when mounted outside.
With the backplate off, remove the backing paper
from the two elements, then stick them to the
inner sides of the reader. The heaters must be
connected to a 24V AC supply (min 25VA).
Mount the Backplate
With the backplate off (see above), mount
the backplate adjacent to the opening edge
of the door and at a convenient height. Feed
the required cables through the backplate:
! The cable from the controller.
! The cable from the heater, if used (must
be a separate cable).
! A cable from a Remote Interface Module
(RIM), if used. A RIM can reduce cable
lengths to door furniture.
Outer gasket
Backplate
Inner
gasket
Backplate
securing screws
You should find that the
backplate has holes for
connection to most
standard electrical
backboxes.
Reader Links
Ensure no jumper is fitted across LK2 (TEST). If a jumper is provided, park it across one pin only. LK4
(AUDIO KB FB) - set to 1 for sound on and 0 for sound off. LK1 (LED BR) - set to H position.
4
Reader Connections
Reader
12V
Controller
connections
(20mA current
loop)
0V
TXTX+
RXRX+
Connect shield at controller
end only (attach to case).
Twisted pairs (use
Belden 9503 cable)
The I/O terminal is for
+12V connection to a RIM (see
RX- the RIM Instructions).
RX+ On completion, re-secure
the reader to the backplate.
I/0
TXTX+
Do not use
0V
Using the Reader
Present the card face-on to the reader until you hear a "bleep". Cards can be presented in rapid
succession; there is no need to wait for the green or red LED to extinguish before presenting another.
If the reader has been enabled for user-code mode at the controller, you can gain access by pressing
the # key, entering your card number, then pressing the * key.
About the Reader LEDs
Green (access
granted) LED
When this LED is lit, the lock is released and you may
open the door.
Red (access
denied) LED
This is lit if you do not have access rights to gain entry, or
if the reader could not read your card (in this case, move
the card away, then present it again).
Flashing amber
(PIN) LED
If the amber LED flashes, enter your PIN. If you make a
mistake, the red LED is lit for a moment, then the flashing
amber prompts you to try again.
Alarm LED
Switch LED
These auxiliary LED indicators can be configured to
operate in conjunction with conditional commands.
9600-0347. Installation and User Instructions for S840 Readers,
Issue 1.0x2 7th January 2004. © AMAG Technology Ltd, 2004.
FCC Notice: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Any unauthorized modification to this device may void the authority of
the user to operate it.
All trademarks acknowledged. HID is a registered trademark of HID
Corporation.
Specifications
Input voltage: 9-14Vdc.
Input current (excl. heater): 110mA @ nom. 12Vdc.
Operating temperature: -13 to 158°F (-25 to 70°C)
without heater.
Operating humidity: 15 to 90%, non-condensing.
Maximum read range: 6" (150mm).
Approvals: EN50133, R&TTE, IP656.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:01:09 09:32:43Z
Creator                         : CorelDRAW(TM) Classic
Modify Date                     : 2004:02:06 10:25:01Z
Page Count                      : 2
Creation Date                   : 2004:01:09 09:32:43Z
Producer                        : Acrobat Distiller 4.05 for Windows
Mod Date                        : 2004:02:06 10:25:01Z
Metadata Date                   : 2004:02:06 10:25:01Z
Title                           : C:\Group4\Hardware manuals\Reader Instructions\s84x\s840 Installation Instructions.eps

EXIF Metadata provided by EXIF.tools