G4S Technology S843 Mifare proximity reader for access control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	364333
Application ID	ZbWk8da0QkfxCaN0+IlVKw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.21kB (252604 bits)
Date Submitted	2003-10-10 00:00:00
Date Available	2003-10-10 00:00:00
Creation Date	2003-10-07 08:57:16
Producing Software	Acrobat Distiller 4.05 for Windows
Document Lastmod	2003-10-10 08:54:35
Document Title	\\Dell-noir\c dell-noir\Group4\Hardware manuals\Reader Instructions\s843\s843.eps
Document Creator	CorelDRAW(TM) Classic

Installation and User Instructions for S843 Readers
The S843 is a contactless smart-card reader, with
®
liquid-crystal display and keypad, able to read Philips
®
MIFARE and Philips MIFARE DESfire formatted
cards.
The S843 uses 20mA current loop pseudo-random
communications.
Fit the Weatherproofing Kit
When mounting outside, the two-part gasket kit
must be fitted:
a) Remove the backplate from the reader
by releasing the two securing
screws.
b) Remove the cutouts and backing paper
from the two gaskets, then stick them to
the backplate as shown.
The optional heater kit maintains the reader at
the correct temperature when mounted
outside. With the backplate off, remove the
backing paper from the two elements, then
stick them to the inner sides of the reader. The
heaters must be connected to a 24V AC supply
(min 25VA).
Outer gasket
Backplate
Inner
gasket
Backplate
securing screws
Mount the Backplate
With the backplate off (see above), mount
the backplate adjacent to the opening edge
of the door and at a convenient height.
Feed the required cables through the
backplate:
! The cable from the controller.
! The cable from the heater, if used (must
be a separate cable).
! A cable from a Remote Interface Module
(RIM), if used. A RIM can reduce cable
lengths to door furniture.
You should find that the
backplate has holes for
connection to most
standard electrical
backboxes.
3
Check the Reader Links
Ensure no jumpers are fitted across LK3 (NODE TERM), LK4 (HGU TERM) and LK2 (TEST). If a jumper
is provided, park it across one pin only. LK1 (USER FB) - set to 1 for sound on and 0 for sound off.
Reader Connections
Controller
connections
(20mA current
loop)
12V
S843 Reader
0V
TX-
+V
RXRX+
I/0
TXTX+
- (not used)
TX+
RXRX+
Connect shield at controller
end only (attach to case).
The I/O terminal is
for connection to a
RIM (see the RIM
Instructions).
On completion, resecure the reader to
the backplate.
Twisted pairs (use
Belden 9503 cable)
0V
If you are using the reader with
a Hand Geometry Unit (HGU),
connect the HGU to PL1.
Using the Reader
Present the card face-on to the reader until you hear a "bleep". Cards can be presented in rapid
succession; there is no need to wait for "UNLOCKED" to disappear before presenting another.
If the reader has been enabled for user-code mode at the controller, you can gain access by pressing
the # key, entering your card number, then pressing the * key.
About the Reader Messages
The reader is waiting for a valid card to be presented.
READY
UNLOCKED
When UNLOCKED is displayed, the lock is released and you
may open the door.
ACCESS DENIED
& LOCKED
These messages are displayed if you do not have access rights
to gain entry, or if the reader did not read your card properly (in
this case, present it again).
ENTER PIN
If the ENTER PIN message is displayed, enter your PIN. If you
make a mistake, the message INCORRECT PIN is momentarily
displayed, followed by ENTER PIN, to prompt you to try again.
Flashing or
steady
These auxiliary indicators can be configured to operate in
conjunction with conditional commands.
9600-0340. Installation and User Instructions for S843
Readers, Issue 1.0x2 7th October 2003. © AMAG Technology
Ltd, 2003.
FCC Notice: This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Any unauthorised modification to this device may void the
authority of the user to operate it.
Specifications
Input voltage: 9-14Vdc.
Input current (excl. heater): 150mA @ nom. 12Vdc.
Operating temperature: -4 to 158°F (-20 to 70°C)
without heater.
Operating humidity: 15 to 90%, non-condensing.
Maximum read range: 1" (25mm).
Approvals: EN50133, R&TTE, IP656.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2003:10:07 08:57:16Z
Creator                         : CorelDRAW(TM) Classic
Modify Date                     : 2003:10:10 08:54:35+01:00
Page Count                      : 2
Creation Date                   : 2003:10:07 08:57:16Z
Producer                        : Acrobat Distiller 4.05 for Windows
Mod Date                        : 2003:10:10 08:54:35+01:00
Metadata Date                   : 2003:10:10 08:54:35+01:00
Title                           : \\Dell-noir\c dell-noir\Group4\Hardware manuals\Reader Instructions\s843\s843.eps

EXIF Metadata provided by EXIF.tools