GE MDS DS-LEDR700S Digital Radio User Manual

GE MDS LLC Digital Radio 3627D LEDR Body

a href="https://usermanual.wiki/GE-MDS" itemprop="url"> GE MDS >

Users Manual

Installation & Operation Guide P/N 05-3627A01, Rev. DJANUARY 2003 Covering LEDR 400S/F, 700S, 900S/F, 1400S/F Models Including Protected (1+1) and Space Diversity Versions LEDR SeriesDigital Microwave Radios Microwave Data Systems Inc.
LEDR Series radios are supplied from the factory in matched pairs and are configured to user’s specifi-cations. There are a few steps necessary to place the pair on-the-air communicating with each other. Once this is done, system-specific parameters will need to be reviewed and changed to match your requirements. Below are the basic steps for installing the LEDR radio. For more detailed instructions, please see “INITIAL STARTUP AND CONFIGURATION” on page 25. When making cable connections, refer to Section 3.6, Rear Panel Connectors , on page 17 for a rear panel view of the radio. 1. Install and connect the antenna system to the radio • Ensure a path study has been conducted and that the radio path is acceptable. • Use good quality, low loss coaxial cable. Keep the cable as short as possible.• Preset directional antennas in the direction of desired transmission/reception. 2. Connect the data equipment to the rear panel data interface • The data interface should be an RJ-45 connector for Fractional-T1, Fractional-E1, or E1, and a DB-25 connector for EIA-530. • Verify the customer premises data equipment is configured as DTE. (By default, the LEDR radio is configured as DCE.) 3. Apply DC power to the radio • Verify that the line voltage matches the power supply input range (typically 24 Vdc or 48 Vdc).• The power connector is a three-pin keyed connector. The power source can be connected with either polarity. The center conductor is not connected.• Ensure the chassis Ground lug is connected to an appropriate ground point. 4. Change SUPER password and set up user access • Login to Network Management System, using the password SUPER . (See “login” on page 68 .)• Change the password using the PASSWD command. ( See “passwd” on page 72. )• Set up required users, passwords and access levels using the USER command, as required.( See “user” on page 86. ) 5. Set the radio’s basic configuration using front panel or Console interface • Set the transmit/receive frequencies ( TX xxx.xxxx / RX xxx.xxxx ) if they need to be changed from the factory settings. (See “freq” on page 59 .)• Refer to this manual for other configuration settings. 6. Verify and set the following parameters as necessary to allow data throughput and intercon- nection with the network. • RF transmit and receive frequencies. (See “freq” on page 59 .)• Radio modulation type and data rate parameters. ( See “modem” on page 71. ).• Data interface clocking. ( See “clkmode” on page 55. ).• Data framing. ( See “fstruct” on page 59. ). Quick-Start instructions continued on the rear cover of this manual.QUICK-START GUIDE
Download:
Mirror Download [FCC.gov]
Document ID312318
Application IDbAPtCFnpVa191/Mqij6Ltw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize244.84kB (3060542 bits)
Date Submitted2003-03-21 00:00:00
Date Available2003-03-21 00:00:00
Creation Date2003-01-31 11:35:49
Producing SoftwareAcrobat Distiller 4.0 for Macintosh
Document Lastmod2003-03-04 09:25:27
Document Title3627D-LEDR_Body.book
Document CreatorFrameMaker 5.5
Document Author: MDS Employee
FCC ID Filing: E5MDS-LEDR700S

Navigation menu