GE MDS DS-SERIES6 Digital Radio System Six.4 Series User Manual user guide

GE MDS LLC Digital Radio System Six.4 Series user guide

user manual

Microwave Data Systems Digital Radio System MDS FOUR.9 Series MDS SIX.4 Series User Reference and Installation Guide PRELIMINARY Part No. 05-4561A01, Rev. A Date: 9 JUNE 2006
© 2006 Microwave Data Systems Inc. All Rights Reserved. This book and the information contained herein is the proprietary and confidential information of Microwave Data Systems Inc. that is provided by Microwave Data SystemsTM exclusively for evaluating the purchase of Microwave Data Systems Inc. technology and is protected by copyright and trade secret laws. No part of this document may be disclosed, reproduced, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Microwave Data Systems Inc. For permissions, contact Microwave Data Systems Inc. Marketing Group at 1-585-241-5510 or 1-585-242-8369 (FAX). Notice of Disclaimer The information and specifications provided in this document are subject to change without notice. Microwave Data Systems Inc. reserves the right to make changes in design or components as progress in engineering and manufacturing may warrant. The Warranty(s) that accompany Microwave Data Systems Inc., products are set forth in the sales agreement/contract between Microwave Data Systems Inc. and its customer. Please consult the sales agreement for the terms and conditions of the Warranty(s) proved by Microwave Data Systems Inc. To obtain a copy of the Warranty(s), contact your Microwave Data Systems Inc. Sales Representative at 1-585-241-5510 or 1-585-242-8369 (FAX). The information provided in this Microwave Data Systems Inc., document is provided “as is” without warranty of any kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability, fitness for a particular purpose, or non-infringement. Some jurisdictions do not allow the exclusion of implied warranties, so the above exclusion may not apply to you. In no event shall Microwave Data Systems Inc. be liable for any damages whatsoever – including special, indirect, consequential or incidental damages or damages for loss of profits, revenue, use, or data whether brought in contract or tort, arising out of or connected with any Microwave Data Systems Inc., document or the use, reliance upon or performance of any material contained in or accessed from this Microwave Data Systems Inc. document. Microwave Data Systems’ license agreement may be provided upon request. Additional Terms and Conditions will be finalized upon negotiation or a purchase. The above information shall not be constructed to imply any additional warranties for Microwave Data Systems Inc. equipment including, but not limited to, warranties of merchantability or fitness for an intended use. Trademark Information Software Defined Indoor UnitTM (SDIDUTM) is a product and trademark of CarrierComm Inc. JavaTM is a trademark of Sun Microsystems Inc. Windows® is a registered trademark of Microsoft Corporation All other brand or product names are trademarks or registered trademarks of their respective companies or organizations.
Table of Contents 1 SAFETY PRECAUTIONS ......................................................................................................................1-1 2 SYSTEM DESCRIPTION .......................................................................................................................2-1 2.1 About This Manual............................................................................................................................2-1 2.2 Introduction.......................................................................................................................................2-1 2.3 System Features ...............................................................................................................................2-5 2.4 Physical Description ........................................................................................................................2-6 2.4.1 Model Types ................................................................................................................................2-6 2.4.2 Options ........................................................................................................................................2-8 2.4.3 Front Panel Indicators .................................................................................................................2-8 2.4.4 Front Panel Connections .............................................................................................................2-9 2.5 System Description ........................................................................................................................2-13 2.6 Consecutive Point Architecture ....................................................................................................2-16 2.7 2 + 0 (East-West) Configuration ....................................................................................................2-18 2.8 1+1 Protection .................................................................................................................................2-19 2.9 1 + 1 Multi-hop Repeater Configuration .......................................................................................2-20 2.10 Data Interfaces ................................................................................................................................2-22 2.11 Power Management ........................................................................................................................2-22 2.12 MDS Digital Radio Series Software and Network Management.................................................2-23 3 INSTALLATION .....................................................................................................................................3-1 3.1 Unpacking..........................................................................................................................................3-1 3.2 Notices ...............................................................................................................................................3-2 3.3 Required Tools..................................................................................................................................3-2 3.3.1 SDIDUTM Tools ............................................................................................................................3-2 3.3.2 ODU Tools...................................................................................................................................3-2 3.4 PRE-INSTALLATION NOTES ...........................................................................................................3-3 3.5 Overview of Installation and Testing Process ...............................................................................3-3 3.6 Site Evaluation ..................................................................................................................................3-5 3.6.1 Preparing for a Site Evaluation....................................................................................................3-6 3.6.2 Site Evaluation Process...............................................................................................................3-7 3.6.3 Critical System Calculations......................................................................................................3-12 3.6.4 Frequency Plan Determination..................................................................................................3-13 3.6.5 Antenna Planning ......................................................................................................................3-14 3.6.6 ODU Transmit Power Setup ......................................................................................................3-15 3.6.7 Documenting a Site Evaluation .................................................................................................3-17 3.7 Installation of the Digital Radio Series .........................................................................................3-20 3.7.1 Installing the Software Defined IDUTM .......................................................................................3-20 3.7.2 Installing the ODU .....................................................................................................................3-21 3.7.3 Routing the ODU/ SDIDUTM Interconnect Cable .......................................................................3-23 3.8 Quick Start Guide ...........................................................................................................................3-25 3.8.1 Materials Required ....................................................................................................................3-25 3.8.2 Grounding the ODU...................................................................................................................3-25
3.8.3 Grounding the SDIDUTM ............................................................................................................3-27 3.8.4 Connecting the SDIDUTM to the PC and Power Source............................................................3-27 3.8.5 SDIDUTM Configuration..............................................................................................................3-28 3.8.6 ODU Antenna Alignment ...........................................................................................................3-30 3.8.7 Quick Start Settings...................................................................................................................3-31 3.9 Documenting MDS FOUR.9 Series Configuration .......................................................................3-32 4 SUMMARY SPECIFICATIONS..............................................................................................................4-1 5 FRONT PANEL CONNECTORS ...........................................................................................................5-1 5.1 DC Input (Power) Connector............................................................................................................5-1 5.2 Ethernet 100BaseTX Payload Connector 1-2.................................................................................5-1 5.3 SONET Payload Connector..............................................................................................................5-2 5.4 STM-1 Payload Connector ...............................................................................................................5-2 5.5 DS-3/E-3/STS-1 Payload Connector................................................................................................5-2 5.6 NMS 10/100BaseTX Connector 1-2 .................................................................................................5-3 5.7 Alarm/Serial Port Connector............................................................................................................5-3 5.8 ODU Connector.................................................................................................................................5-4 5.9 T1- Channels 1-2 Connector............................................................................................................5-4 5.10 T1- Channels 3-16 Connector..........................................................................................................5-5 5.11 USB ....................................................................................................................................................5-7 5.12 Voice Order Wire...............................................................................................................................5-8 5.13 Data Order Wire ................................................................................................................................5-8 6 APPENDIX .............................................................................................................................................6-1 6.1 Alarm Descriptions...........................................................................................................................6-1 6.2 Abbreviations & Acronyms............................................................................................................6-14
© 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 1 Safety Precautions PLEASE READ THESE SAFETY PRECAUTIONS! RF Energy Health Hazard—FOUR.9 Series The radio equipment described in this guide employs radio frequency transmitters. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. Do not allow people to come closer than 119 cm (47.2 inches) to the front of the antenna while the transmitter is operating. The antenna must be professionally installed on a fixed-mounted outdoor permanent structure to provide separation from any other antenna and all persons as detailed in this manual. RF Energy Health Hazard—SIX.4 Series The radio equipment described in this guide employs radio frequency transmitters. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. Do not allow people to come closer than 3.17 meters (124.80 inches) to the front of the antenna while the transmitter is operating. The antenna must be professionally installed on a fixed-mounted outdoor permanent structure to provide separation from any other antenna and all persons as detailed in this manual. Protection from Lightning Article 810 of the US National Electric Department of Energy Handbook 1996 specifies that radio and television lead-in cables must have adequate surge protection at or near the point of entry to the building. The code specifies that any shielded cable from an external antenna must have the shield directly connected to a 10 AWG wire that connects to the building ground electrode. Warning – This is a Class A product Warning – This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Warning – Turn off all power before servicing
User Reference and Installation Guide 1-2 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Warning – Turn off all power before servicing this equipment. Safety Requirements Safety requirements require a switch be employed between the SDIDU™ external power supply and the SDIDU™ power supplies. Proper Disposal The manufacture of the equipment described herein has required the extraction and use of natural resources. Improper disposal may contaminate the environment and present a health risk due to the release of hazardous substances contained within. To avoid dissemination of these substances into our environment, and to lessen the demand on natural resources, we encourage you to use the appropriate recycling systems for disposal. These systems will reuse or recycle most of the materials found in this equipment in a sound way. Please contact Microwave Data Systems or your supplier for more information on the proper disposal of this equipment.
© 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 2 System Description 2.1 About This Manual This manual is written for those who are involved in the installation and use of the MDS FOUR.9 Series or MDS SIX.4 Series Digital Radio System, including installation technicians, site evaluators, project managers, and network engineers. The transceivers are comprised of a Software Defined Indoor UnitTM (SDIDUTM) and outdoor unit (ODU). The SDIDUTM is a product and trademark of CarrierComm. This manual assumes the reader has a basic understanding of how to install hardware, use Windows based software, and operate test equipment. For the purposes of this manual, the radios are referred to as the “Digital Radio Series” except where it is necessary to make a distinction between the models covered or their operating frequency ranges. 2.2 Introduction The Microwave Data Systems family of digital radios provides high capacity transmission, flexibility, features, and convenience for wireless communications networks. These radios represent a new microwave architecture that is designed to address universal applications for both PDH and SDH platforms. This advanced technology platform provides the flexibility customers need for their current and future network requirements. The radio family is based on a common platform used to support a wide range of network interfaces and configurations. It supports links for 16 x E1/T1, 100BaseTX Ethernet, and DS-3/E-3/STS-1 (optional, consult factory for availability). The radio family is spectrum and data rate scalable, enabling service providers or organizations to trade-off system gain with spectral efficiency and channel availability for optimal network connectivity. The radio family enables network operators (mobile and private), government and access service provides to offer a portfolio of secure, scalable wireless applications for data, video, and Voice over IP (VoIP). The MDS FOUR.9 Series digital radio family operates in the FCC Public Safety Band of 4.940 to 4.990 GHz, which is generically referred to as the “4.9 GHz band.” It supports three types of user data payload connectivity as follows: • 100Base-TX intelligent bridging between two locations without the delay and expense of installing cable or traditional microwave. • Scalable Ethernet capability of 25 and 50 Mbps is included. These scalable radios provide LAN connectivity and offer performance trade-offs between operational bandwidths, data rates, and distance.
User Reference and Installation Guide 2-2 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A • 16E1 or T1 for cellular backhaul, enterprise voice applications and voice network redundancy The MDS SIX.4 Series digital radio family operates in the FCC Fixed Microwave Services band of 5.925 to 6.425 GHz, which is generically referred to as the “6.4 GHz band.” It supports four types of user data payload connectivity as follows: • Gigabit Ethernet intelligent bridging between two locations without the delay and expense of installing cable or traditional microwave. • Scalable Ethernet capability of 16 to 131 Mbps is included. These scalable radios provide LAN connectivity and offer performance trade-offs between operational bandwidths, data rates, and distance. • 32 T1 for cellular backhaul, enterprise voice applications and voice network redundancy with 85 Mbps of Ethernet • SONET (Synchronous Optical Network) For customers such as cellular carriers requiring backhaul and backbone extension as well as service providers requiring network redundancy, new Points of Presence (POPs), and last mile access, the Digital Radio Series is a cost effective alternative to leased lines with carrier-class quality of performance. The Digital Series radio is a cost effective solution to meet the growing demand for enterprise Local Area Network (LAN) connectivity between buildings and campuses as well as service providers requiring reliable products for infrastructure expansion, extending Metropolitan Area Network (MAN) fiber access, and network redundancy. The Digital Series includes integrated Network Management functionality and design features that enable simple commissioning in the field at the customer’s premises. Furthermore, a highlight of MDS radio products is scalability and the capability to support a ring-type architecture. This ring or consecutive point radio architecture is “self-healing” in the event of an outage in the link and automatically re-routes data traffic to ensure that service to the end user is not interrupted. The Digital Series radio system is composed of a Software Defined Indoor UnitTM (SDIDUTM) and Outdoor Unit (ODU). It supports 1+0 and 1+1 protection and ring architectures in a single 1 Rack Unit (1RU) chassis. The modem and power supply functions are supported using easily replaceable plug-in modules. An additional feature of the SDIDUTM is provision for a second plug-in modem/IF module to provide repeater or east/west network configurations. The overall architecture consists of a single 1RU rack mount Software Defined Indoor Unit (SDIDUTM) with a cable connecting to an Outdoor Unit (ODU) with an external antenna.
User Reference and Installation Guide 2-3 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Core AccessNetworkIndoor UnitIndoor UnitIndoor UnitOutdoorUnitOutdoorUnitOutdoorUnitOutdoorUnitOutdoorUnitOutdoorUnit Figure 2-1. MDS Digital Radio Series SDIDUTM and ODU Architecture Table 2-1 lists key features that Digital Radio Series technology offers to those involved in the design, deployment and support of broadband fixed wireless networks. Table 2-1 Key Benefits and Advantages of MDS Digital Radio Series Benefits Advantages to Providers/Customers Reference Wireless license-free system (FOUR.9 only): ISM bands do not require expensive license band fees or incur licensing delays. Wireless licensed system (SIX.4 only): No interference from other services as this band is licensed to the user. Wireless connectivity supplements existing cable (Ethernet). Fast return on investment. Lower total cost of total ownership. Media diversity avoids single points of failure. 146H143H2.2 –147H144H2.4 Easy to install units Straightforward modular system enables fast deployment and activation. Carrier-class reliability. Fast return on investment. No monthly leased line fees. 148H145H3.5 Complete support of payload capacity with additional wayside channels Aggregate capacity beyond basic payload: FOUR.9 Series—34 Mbps, 50 Mbps or 100 Mbps. SIX.4 Series—16 to 131 Mbps Increases available bandwidth of network. Allows customer full use of revenue-generating payload channel. 149H146H2.2– 150H147H2.5
User Reference and Installation Guide 2-4 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Benefits Advantages to Providers/Customers Reference Scalable and spectrally efficient system. Separate networks for radio overhead/management and user payload. Up to 16 (FOUR.9 Series) or 32 (SIX.4 Series) T1/E1 wayside channels support extension of PBX connectivity between buildings without additional leased-line costs. Lowers total cost of ownership. Ring Architecture Supports a ring (consecutive point) configuration, thus creating a self-healing redundancy that is more reliable than traditional point-to-point networks. In the event of an outage, traffic is automatically rerouted via another part of the ring without service interruption. Ring/consecutive point networks can overcome line-of-sight issues and reach more buildings than other traditional wireless networks. Networks can be expanded by adding more Digital Radio Series units, or more rings without interruption of service. A separate management channel allows for a dedicated maintenance ring with connections to each radio on the ring. Enables network scalability. Increases deployment scenarios for initial deployment as well as network expansion with reduced line-of-sight issues. Increases network reliability due to self-healing redundancy of the network. Minimizes total cost of ownership and maintenance of the network. Allows for mass deployment. 2.6,2.7,2.9 Adaptive Power Control Automatically adjusts transmit power in discrete increments in response to RF interference. For EIRP compliance, the power output is limited to the maximum established at the time of installation, per FCC Part 90 (FOUR.9 Series) or 101 (SIX.4 Series) rules. Enables dense deployment. Simplifies deployment and network management. 2.11 Comprehensive Link/Network Management Software A graphical user interface offers security, configuration, fault, and performance management via standard craft interfaces. Suite of SNMP-compatible network management tools that provide robust local and remote management capabilities. Simplifies management of radio network and minimizes resources as entire network can be centrally managed from any location. Simplifies troubleshooting of single radios, links, or entire networks. 2.12
User Reference and Installation Guide 2-5 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Benefits Advantages to Providers/Customers Reference Simplifies network upgrades with remote software upgrades. Allows for mass deployment. 2.3 System Features  Selectable Rates and Interfaces o Up to 16 (FOUR.9 Series) or 32 (SIX.4 Series) x E1/T1 (wayside channels) o 100BaseTX/Ethernet: Scalable 25-50 Mbps (FOUR.9 Series) or 16 to 131Mbps (SIX.4 Series) o DS-3/E-3/STS-1 (option; consult factory for availability)  Support for multiple configurations o 1+0, 1+1 protection/diversity o Hot Standby o East/West Repeater (2 + 0)  Selectable Spectral Efficiency of 0.8 to 6.25 bits/Hz (FOUR.9 Series) or 5 to 7 bits/Hz (SIX.4 Series). These figures include FEC and spectral shaping effects.  16 – 64 QAM Modulation (FOUR.9 Series) or 32 – 64 QAM Modulation (SIX.4 Series)  Powerful Trellis Coded Modulation concatenated with Reed-Solomon Error Correction  Built-in Adaptive Equalizer  Support of Voice Orderwire Channels  Peak output power at antenna port (FOUR.9 Series): o 24.4 dBm at 4.9 GHz (High Power) o 17.1 dBm at 4.9 GHz (Low Power)  Peak output power at antenna port (SIX.4 Series): o 26 dBm at 6.4 GHz (High Power) o 8 dBm at 6.4 GHz (Low Power)
User Reference and Installation Guide 2-6 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A  Receive Sensitivity: -84 dBm to -72 dBm (depending on data rate/modulation/FEC/ODU)  Adaptive Power Control—Adjusts power output to account for changing path conditions. Power is limited to the maximum established at the time of installation, per FCC Part 90.  Built-in Network Management System (NMS)  Consecutive Point ring architecture  Built-in performance statistics o Built-in Bit Error Rate (BER) performance monitoring  Data encryption of all payload data and T1/E1 wayside channels for Series-100 radios and Series-50 Ethernet models (Consult factory for availability) 2.4 Physical Description The following section details the physical features of the Digital Series digital radios • Model types • Front panel indicators • Front panel connections 2.4.1 Model Types 158H155HTable 2-2 lists the radio series according to model number and associated capabilities of throughput, data interface, and wayside channel. 159H 156H Table 2-3 lists the ODU model numbers. Table 2-2 MDS Digital Radio Series SDIDUTM Model Types MODEL NUMBER* FULL DUPLEX THROUGHPUT DATA INTERFACE WAYSIDE SDIDUxxMNVN 100 Mbps Aggregate (50 Mbps full duplex) 100 BaseTX Two T1/E1s
User Reference and Installation Guide 2-7 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A MODEL NUMBER* FULL DUPLEX THROUGHPUT DATA INTERFACE WAYSIDE SDIDUxxMPVN 100 Mbps Aggregate (50 Mbps full duplex), 1+1 Protection or 2+0 100 BaseTX Two T1/E1s SDIDUxxMNCN 200 Mbps Aggregate (100 Mbps full duplex) 100 BaseTX Two T1/E1s SDIDUxxMPCN 200 Mbps Aggregate (100 Mbps full duplex), 1+1 Protection or 2+0 100 BaseTX Two T1/E1s SDIDUxxMNTN 68 Mbps Aggregate (34 Mbps full duplex) + scalable Ethernet 1-16xE1/T1 Scalable Ethernet, 2 Mbps SDIDUxxMPTN 72 Mbps Aggregate (36 Mbps full duplex), 1+1 Protection or 2+0 1-16xE1/T1 Scalable Ethernet, 2 Mbps * “xx” changes in accordance with the frequency range of radio; 49 for 4.9 GHz, 64 for 6.4 GHz) Table 2-3 MDS Digital Radio Series ODU Model Types PRODUCT NAME MODEL NUMBER ANTENNA MDS FOUR.9 - ODU49e ODU4900MEP External antenna required MDS SIX.4 – ODU* ODU6400MLL Transmit: 5929 – 6110 MHz Receive: 6181 – 6362 MHz External antenna required MDS SIX.4 – ODU* ODU6400MLH Transmit: 6181 – 6362 MHz Receive: 5929 – 6110 MHz External antenna required
User Reference and Installation Guide 2-8 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A MDS SIX.4 – ODU* ODU6400MHL Transmit: 5988 – 6169 MHz Receive: 6240 – 6421 MHz External antenna required MDS SIX.4 – ODU* ODU6400MHH Transmit: 6240 – 6421 MHz Receive: 5988 – 6169 MHz External antenna required * To support the FCC Part 101 6.4 GHz band plan, four separate ODUs are required to cover the frequencies as listed above. 2.4.2 Options The following items are also available: • AC/DC power supply • Data Encryption • OC-3/STM-1 Mini-IO Module Please consult the factory for more information. 2.4.3 Front Panel Indicators All models of the Digital Radio Series support a variety of front panel configurations that are dependent on the network interface and capacity configurations. 160H157HFigure 2-2 provides an example of a 1+0 configuration and the associated LEDs displayed on the SDIDUTM front panel. The controller, standard I/O, and each modem card have a status LED. Figure 2-2. Front Panel LEDs: SDIDUTM Configuration for 1+0 Configuration The modem status LED indicates the modem status as described in Table 2-4.
User Reference and Installation Guide 2-9 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Table 2-4. Modem status LED. LED STATUS Green Active Locked Link Orange Standby Locked Link (1+1 Non-Diversity Only) Flashing Green Low SNR Flashing Orange Unlocked The controller status LED is the primary front panel indicator of alarms. An alarm is generated when a specific condition is identified and is cleared when the specified condition is no longer detected. When an alarm is posted, 1. The controller status LED turns orange for 5 seconds 2. The controller status LED turns off for 5 seconds 3. The controller status LED flashes orange the number of times specified by the first digit of the alarm code 4. The controller status LED turns off for 3 seconds 5. The controller status LED flashes orange the number of times specified by the second digit of the alarm code Steps 2 through 5 are repeated for each alarm posted. The entire process is repeated as long as the alarms are still posted. The standard I/O and modem status LEDs are set to red when certain alarms are posted. A complete list of alarms is provided in Appendix 161H158H6.1. The alarm description is also displayed in the Graphical User Interface (GUI) as described in the User Interface Reference Manual. 2.4.4 Front Panel Connections Please refer to the 162H159HFigure 2-3 for an example of the SDIDUTM front panel followed by a descriptive text of the connections.
User Reference and Installation Guide 2-10 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Figure 2-3. Front Panel Connections, 1+1 Protection: SDIDUTM
User Reference and Installation Guide 2-11 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Power Supply Input DC Input -48 VDC -48v (Isolated Input); 2-pin captive power connector. The unit requires an input of -48 volts dc ±10% at the front panel DC Input connector. The total required power is dependent on the option cards and protection configuration (1+0, 1+1). The SDIDUTM front panel power connector pin numbering is 1 through 2, from left to right, when facing the unit front panel. Pin 1 is the power supply return and is connected to unit chassis ground internally. Pin 2 should be supplied with a nominal -48 V dc, with respect to the unit chassis (ground). A ground-isolated supply may be used, provided it will tolerate grounding of its most positive output. The recommended power input is -44 to -52 V dc at 2 Amps minimum. It is recommended that any power supply used be able to supply a minimum of 100 Watts to the SDIDUTM. A mating power cable connector is supplied with the SDIDUTM. It is a 2-pin plug, 5 mm pitch, manufactured by Phoenix Contact, P/N 17 86 83 1 (connector type MSTB 2,5/2-STF). This connector has screw clamp terminals that accommodate 24 AWG to 12 AWG wire. The power cable wire should be selected to provide the appropriate current with minimal voltage drop, based on the power supply voltage and length of cable required. The recommended wire size for power cables under 10 feet in length supplying -48 Vdc is 18 AWG. The SDIDUTM supplies the ODU with all required power via the ODU/SDIDUTM Interconnect cable. The SDIDUTM does not have a power on/off switch. When DC power is connected to the SDIDUTM, the digital radio powers up and is operational. There can be up to 204 mW of RF power present at the antenna port (external antenna version). The antenna should be directed safely when power is applied.
User Reference and Installation Guide 2-12 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Alarm/Serial Interface Alarms/Serial DB-15HD female connector for two Form-C relay alarm outputs (rated load: 1A @ 24 VDC), two TTL alarm outputs, four TTL alarm inputs, and Serial Console. The two Form-C relay alarm outputs can be configured to emulate TTL alarm outputs. USB Interface USB USB connector, optional. Voice Orderwire Connector Voice Orderwire Call Call button to alert operator at link-partner SDIDUTM of incoming Voice-Orderwire call. Voice Orderwire RJ-11 modular port connector for voice orderwire interface. NMS 10/100 Network Management System Connections NMS 10/100 1 10/100Base-TX RJ-45 modular local port connector for access to the Network Management System (SNMP) and GUI. NMS 10/100 2 10/100BaseTX RJ-45 modular remote port connector for access to the Network Management System (SNMP). This port to be used for consecutive point networks. 100/Ethernet Models: Ethernet 100BaseT Connections USER 10/100 1 100Base-TX RJ-45 modular port connector for the local Fast Ethernet interface. USER 10/100 1 100Base-TX RJ-45 modular port connector. This port to be used for consecutive point networks. T1 Channels T1 1-2 Two T1/E1 (RJ-48C) interface connections. T1 3-16 Fourteen T1/E1 high density interface connector
User Reference and Installation Guide 2-13 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A 2.5 System Description The overall digital radio architecture consists of a single 1RU rack mount Software Defined Indoor UnitTM (SDIDUTM) with a cable connecting to an Outdoor Unit (ODU). The ODU is designed for use with an external antenna only. This SDIDUTM/ODU architecture is advantageous when compared to a single IDU with external mount antenna, since supporting a signal from the IDU rack to the antenna can result in significant signal losses, which would be difficult to avoid without the use of expensive coaxial cable or a waveguide. 163H160HFigure 2-4 shows the SDIDUTM and interfaces from a functional point of view. The functional partitions for the I/O, Modem/IF, and power supply modules are shown. The SDIDUTM comes with the standard I/O capability that can be upgraded. In addition, the Modem/IF function is modular. This allows the addition of a second Modem to support protection or ring architectures. The power supply is similarly modular.
User Reference and Installation Guide 2-14 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A ExternalAntennaInternal/ HorizontalAntennaTransferSwitch DuplexerDiversitySwitchTransmitterUp-ConverterReceiverDown-Converter350MHz140MHzDC/DCConverters-48Vdc +10Vdc+5Vdc+3Vdc-5VdcCommlink& Processor5/10MHzODURSL(Received Signal Level)VoltageVerticalAntennaTNCN-typeBNC5.3/5.8 GHzFRAMERSTM-1/OC3DS-3/ES/STS-12xSTM-1/OC34xDS3/ES/STS1Future64 kbps Voice16 T1/E1User 2x 100Base-Tx Switch MODEM/FEC ASICMODEM/FEC ASIC4x44.736/34.368/51.84 Mbps2x 155.52 Mbps4x44.736/34.368/51.84 Mbps155.52 Mbps2x 100 Mbps16x 1.544/2.048 MbpsDigitalIFQuadMuxSNMP 2x 100Base-Tx SwitchCPUEast/Primary ModemWest/Secondary ModemDigitalIFQuadMux2x 100 MbpsIDU CONTROLLEROptional I/O Cards(Small Slot)Standard I/O CardsOptional I/O Cards(Large Slot)Primary Power SupplySecondary Power SupplySerialRCH SerialModem ControlTelemetryIDU-48Vdc-48VdcQuadMux-48Vdc-48VdcMultiplexedIFMultiplexedIF Figure 2-4. MDS Digital Radio Series System Block Diagram The SDIDUTM interfaces with the ODU to receive and provide modulated transmit and receive waveforms. The SDIDUTM interfaces provide Fast Ethernet 100Base-T connections to the network. Contact the factory for availability of SONET OC-3 connections. In addition, two E1/T1 channels are provided for PBX extension. SNMP is provided on 10/100BaseT ports.
User Reference and Installation Guide 2-15 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A The ODU RF Up/Down Converter card provides the interface to the antenna. The transmit section up-converts and amplifies the modulated Intermediate Frequency (IF) of 350 MHz from the IF Processor and provides additional filtering. The receive section down converts the received signal, provides additional filtering, and outputs an IF of 140 MHz to the IF Processor. The 64-QAM Modem performs the modulation and demodulation of the payload and forward error correction using advanced modulation and coding techniques. Using all-digital processing, the 64-QAM Modem uses robust modulation and forward error correction coding to minimize the number of bit errors and optimize the radio and network performance. The 64-QAM Modem also scrambles, descrambles and interleaves/de-interleaves the data stream in accordance with Intelsat standards to ensure modulation efficiency and resilience to sustained burst errors. The modulation will vary by application, data rate, and frequency spectrum. The highest order modulation mode supported is 64 Quadrature Amplitude Modulation (QAM). 164H161HTable 2-5 summarizes the TCM/convolutional code rates for each modulation type supported by the MDS Digital Radio Series. Table 2-5. MDS Digital Radio Series TCM/Convolutional Code Rates Modulation Type Available Code Rates 16-QAM 3/4, 7/8, 11/12 32-QAM 4/5, 9/10 64-QAM 5/6, 11/12 The major functions of the SDIDUTM can be summarized as follows: • I/O Processing – The SDIDUTM comes with a standard I/O capability that includes support for up to 16xT1/E1 and 2x100Base-TX user payloads, 2x100Base-TX for SNMP, and voice orderwire. In addition, option cards for DS-3/E3/STS-1, 1-2 x STM-1/OC-3, and 4xDS-3/E3/STS-1 may be added. The SDIDUTM architecture is flexible and allows for the addition of other I/O types in the future. • Switch/Framing – The SDIDUTM includes an Ethernet Switch and a proprietary Framer that are designed to support 1+1 protection switching, ring architecture routing, and overall network control functions. • Network Processor – The SDIDUTM includes a Network Processor that performs SNMP and Network Management functions. • Modem/IF – The SDIDUTM Modem performs forward-error-correction (FEC) encoding, PSK/QAM modulation and demodulation, equalization, and FEC decoding functions. The IF chain provides a 350 MHz carrier, receives a 140 MHz carrier, processes OOK telemetry, and provides –48V power. Two modems can be used for 1+1 protection or ring architectures. • Power Supply – The SDIDUTM power supply accepts -48 Vdc and supplies the SDIDUTM and ODU with power. A second redundant power supply may be added as an optional module. The Modem Processor and its associated RAM, ROM, and peripherals control the digital and analog Modem operation. It also provides configuration and control for both the IF and I/O cards. The
User Reference and Installation Guide 2-16 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A SDIDUTM interfaces with the ODU to receive and provide modulated transmit and receive waveforms. The SDIDUTM also provides the physical interface for the user payload and network management. In transmit mode, the Framer merges user payload with radio overhead-encapsulated network management data. This combined data stream is transmitted without any loss of user bandwidth. In the receive mode, the Framer separates the combined data stream received from the 64-QAM Modem. The SDIDUTM supports Scalable Ethernet data rates, such as 25 or 50 Mbps via the 100BaseT data interface port. The SDIDUTM provides network management data on 10 Mbps ports accessible via the 10/100BaseTX port. The Central Processor Unit (CPU) provides the embedded control and network element functionality of the NMS. The CPU also communicates with other functions within the SDIDUTM for configuration, control, and status monitoring. In Ethernet models, the payload of each user Ethernet data packet and all T1 can be encrypted using an AES encryption algorithm. In addition, the encryption engine is re-seeded with a new, randomly generated key stream every 10 seconds, in order to provide enhanced security. The initial key is based off of a pass phrase entered into each Digital Radio Series unit by the network administrator. Consult factory for the availability of this encryption function. The power supply converts -48 Vdc to the DC voltage levels required by each component in the system. 2.6 Consecutive Point Architecture The consecutive point network architecture of the Digital Radio Series is based upon the proven SONET/SDH ring. Telecommunications service providers traditionally use the SONET/SDH ring architecture to implement their access networks. A typical SONET/SDH network consists of the service provider’s Point of Presence (POP) site and several customer sites with fiber optic cables connecting these sites in a ring configuration (see 165H162HFigure 2-5). This architecture lets providers deliver high bandwidth with high availability to their customers.
User Reference and Installation Guide 2-17 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Figure 2-5. Ring Configuration. SONET/SDH rings are inherently self-healing. Each ring has both an active path and a standby path. Network traffic normally uses the active path. Should one section of the ring fail, the network will switch to the standby path. Switchover occurs in seconds. There may be a brief delay in service, but no loss of payload, thus maintaining high levels of network availability. The consecutive point architecture implemented in the Digital Radio family is based on a point-to-point-to-point topology that mimics fiber rings, with broadband wireless links replacing in-ground fiber cable. A typical consecutive point network consists of a POP and several customer sites connected using MDS Digital Radio Series units. These units are typically in a building in an east/west configuration. Using east/west configurations, each unit installed at a customer site is logically connected to two other units via an over-the-air radio frequency (RF) link to a unit at an adjacent site. Each consecutive point network typically starts and ends at a POP. A pattern of wireless links and in-building connections is repeated at each site until all buildings in the network are connected in a ring as shown in 166H163HFigure 2-6. . For 2 x 1+0 and 2 x 1+1 nodes payload and NMS connections need to be jumpered between two SDIDUTMs. For 1 x 2+0 nodes, there is no need for jumpers as there is a single SDIDUTM. For SDH or SONET payloads, the configuration is similar but an external add/drop MUX and a second SDH/SONET interface card are required.
User Reference and Installation Guide 2-18 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Figure 2-6. Consecutive Point Network 2.7 2 + 0 (East-West) Configuration The SDIDUTM supports an east/west, or 2+0, configuration that allows a consecutive point architecture to be achieved with only a single 1 RU chassis at each location. In this configuration the SDIDUTM contains two modems supplies and may contain two power supplies. One modem is referred to as the west modem and the other as the east modem. The SDIDUTM is connected to two ODUs, one broadcasting/receiving in one direction of the ring architecture and the other broadcasting/receiving in the other as shown in Figure 2-7.
User Reference and Installation Guide 2-19 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Connected toeast modemConnected towest modemConnected toeast modemConnected towest modemConnected towest modemConnected toeast modemConnected towest modemConnected toeast modem Figure 2-7. 2+0 (East-West) configuration. 2.8 1+1 Protection The MDS Digital Radio Series supports 1+1 protection as an option for a critical link. In this configuration, protection is provided in a single 1 RU chassis. The SDIDUTM contains two power supplies and two modems. The power supply, ODU, IF/telemetry and modem are protected. The digital framing and LIUs are not. One modem is referred to as the west modem and the other as the east modem. 1+1 protection can be run in two modes called diversity and non-diversity. In diversity mode, the link between each pair of modems is the same, as shown in 168H165HFigure 2-8, providing complete redundancy. This arrangement requires bandwidth for both links and non-interference between the links, but it provides hitless receive and transmit switching. The SDIDUTM supports both frequency and spatial diversity. In frequency diversity, two frequencies are used. In spatial diversity, two non-interfering paths are used. In either case, the proprietary framer chooses the best, or error-free, data stream and forwards it to the Line Interface Units (Luis).
User Reference and Installation Guide 2-20 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Connected toeast modemConnected towest modemConnected towest modemConnected toeast modem Figure 2-8. 1+1 protection in diversity mode 169H166HFigure 2-9 shows operation in non-diversity mode. In this mode, one ODU at each location transmits to both two ODUs at the other location. This mode does not require the extra bandwidth or interference protection of diversity mode. It provides hitless receive switching and hot standby. The SDIDUTM automatically switches transmit ODU upon appropriate ODU alarm or ODU interface error, minimizing transmit outage time. Connected towest modemConnected toeast modemConnected towest modemConnected toeast modem Figure 2-9. 1+1 protection in non-diversity mode 2.9 1 + 1 Multi-hop Repeater Configuration The MDS Digital Radio Series supports a 1 + 1 multi-hop repeater configuration with drop/insert capability as shown in 171H168HFigure 2-10. This configuration provides individual 1 + 1 link protection as described in section 172H169H2.8, as well as the full-scale protection inherent in the consecutive point architecture as described in section 173H170H2.6. At each location within the network, data may be dropped or inserted. Front panel connections for drop/insert capability are shown in 174H171HFigure 2-11. In this configuration each SDIDUTM contains two power supplies and two modems.
User Reference and Installation Guide 2-21 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Datadrop/insertDatadrop/insertDatadrop/insertDatadrop/insertProtectedLinkProtectedLinkProtectedLinkProtectedLinkFigure 2-10. 1 + 1 Multi-hop Repeater Configuration
User Reference and Installation Guide 2-22 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A Figure 2-11. Front Panel connections in 1 + 1 multi-hop repeater configuration 2.10 Data Interfaces The I/O card has 2x100BaseTX interfaces that can be configured as either primary payload, or secondary wayside channels. The Over-the-air channel has a data-bandwidth capacity that is set by the frequency-bandwidth, modulation, and coding. The data-bandwidth may be allocated to various I/O card interfaces, including STM-1, 2 Mbps per E1, up to 50 Mbps Ethernet, and up to 1 Mbps NMS. Only up to 100 Mbps of data-bandwidth may be allocated for Ethernet data, and the two I/O card 100BaseTX interfaces will share that 100 Mbps data-bandwidth. There is also an option mini-I/O card, which provides STM-1 Optical/OC-3 or STM-1 Electrical interfaces. The optical interface is single mode at 1300 nm. Consult factory for availability of Mini-IO STM-1/OC-3 Module. 2.11 Power Management RF power management is a radio design feature that controls the power level (typically expressed in dBm) of the RF signal received from a transmitter by a receiver. The traditional goal of power management is to ensure that the RF signal at a receiver is strong enough to maintain the radio link under changing weather and link conditions. Traditional power management techniques such as Constant Transmit Power Control (CTPC) and Automatic Transmit Power Control (ATPC) transmit at a high power level to overcome the effects of fading and interference. However, these techniques continue to operate at a higher
User Reference and Installation Guide 2-23 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS Digital Radio Series 05-4561A01, Rev. A power level than needed to maintain the link in clear weather. Because transmit power remains high when the weather clears, the level of system interference increases. Radios operating at high transmit power will interfere with other radios, even if the interfering source is miles away from the victim. High interference levels can degrade signal quality to the point that wireless radio links become unreliable and network availability suffers. The traditional solution to system interference is to increase the distance between radios. However, the resulting sparse deployment model is inappropriate for metropolitan areas. In response to the need for a high-density deployment model the MDS Digital Radio Series use a unique power control technique called AdTPC. AdTPC enables MDS Digital Radio Series units to transmit at the minimum power level necessary to maintain a link regardless of the prevailing weather and interference conditions. The MDS Digital Radio Series is designed and manufactured to not exceed the +23 dBm maximum power allowed. The purpose of power management is to minimize transmit power level when lower power levels are sufficient. AdTPC also extends the concept of power management by controlling not only the power (dBm) of the RF signal, but its quality (signal-to-noise ratio) as well. In contrast to ATPC, the AdTPC technique dynamically adjusts the output power based on both the actual strength and quality of the signal. Networked radios constantly monitor receive power and maintain 10-12 BER performance under varying interference and climate conditions. Each radio detects when there is a degradation in the received signal level of quality and adjusts the transmit power level of the far-end unit to correct for it. AdTPC provides maximum power in periods of heavy interference and fading and minimum power when conditions are clear. Minimal transmit power reduces potential for co-channel and adjacent channel interference with other RF devices in the service area, thereby ensuring maximum frequency re-use. The resulting benefit is that operators are able to deploy more radios in a smaller area. 2.12 MDS Digital Radio Series Software and Network Management All Digital Radio Series parameters are accessible in three ways: 1. Using a standard web-browser via HTTP to access the built in webserver. 2. Via SNMP using the fully featured MIB, allowing for automation of data collection and network management. 3. Via a command line client accessible from a terminal client connected to the serial port, or telnet over the NMS Ethernet. The GUI, SNMP, and CLI control are discussed in the Digital Radio Series User Interface Manual.
© 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3 Installation 3.1 Unpacking The following is a list of possible included items. Description Quantity Digital Radio SDIDUTM (1RU chassis) 1 ODU (with hardware) 1 Manual and/or Quick Start Guide 1 ODU SDIDUTM Figure 3-1. MDS Digital Radio Series Components Be sure to retain the original boxes and packing material in case of return shipping. Inspect all items for damage and/or loose parts. Contact the shipping company immediately if anything appears damaged. If any of the listed parts are missing, call the distributor or the factory immediately to resolve the problem.
User Reference and Installation Guide 3-2 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3.2 Notices CAUTION DO NOT OPERATE EXTERNAL ANTENNA ODU UNITS WITHOUT AN ANTENNA, ATTENUATOR, OR LOAD CONNECTED TO THE ANTENNA PORT. DAMAGE MAY OCCUR TO THE TRANSMITTER DUE TO EXCESSIVE REFLECTED RF ENERGY. ALWAYS ATTENUATE THE SIGNAL INTO THE RECEIVER ANTENNA PORT TO LESS THAN –20 dBm. THIS WILL PREVENT OVERLOAD AND POSSIBLE DAMAGE TO THE RECEIVER MODULE. WARNING HIGH VOLTAGE IS PRESENT INSIDE THE ODU and SDIDUTM WHEN THE UNIT IS PLUGGED IN. TO PREVENT ELECTRICAL SHOCK, UNPLUG THE POWER CABLE BEFORE SERVICING. UNIT SHOULD BE SERVICED BY QUALIFIED PERSONNEL ONLY. 3.3 Required Tools The following tools are needed for installation. 3.3.1 SDIDUTM Tools • 1/8” Slotted screwdriver for securing power supply connector • Screwdriver for rack mount assembly. Size and types depends on rack mount screws (not included). 3.3.2 ODU Tools • 13 mm or adjustable wrench for ODU bracket mounting bolts • 17 mm or adjustable wrench for U-Bolt
User Reference and Installation Guide 3-3 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3.4 PRE-INSTALLATION NOTES It may be useful to gain familiarity with the MDS Digital Radio Series via back-to-back bench testing prior to final installation. We highly recommend installation of lightning protectors on the ODU/SDIDUTM Interconnect Cable to prevent line surges from damaging expensive components. Back-to-back bench testing prior to final installation is highly recommended in order to gain familiarity with the product. The following additional equipment is required for back-to-back testing: • Low-loss cables, N-male connectors on ODU interfaces. • Two inline RF attenuators, 30 dB each, rated for ODU frequency. The SDIDUTM and ODUs must be configured in an operational configuration and set-up as shown in 175H172HFigure 3-2. When equipment is connected in operational configuration, no errors should be reported on the front panel. ODU - 1SDIDU - 1To IDUAnt. PortODU - 2SDIDU - 230 dB 30 dBTM TMAnt. Port Figure 3-2. MDS Digital Radio Series Back-to-Back Testing Configuration 3.5 Overview of Installation and Testing Process The installation and testing process is accomplished by performing a series of separate, yet interrelated, procedures, each of which is required for the successful implementation of a production Digital Radio Series network. These procedures are as follows: • Site Evaluation: gathering specific information about potential radio installation sites.
User Reference and Installation Guide 3-4 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A • Cable and Installation: Testing and installing ODU cables and optional interface devices at installation sites. • ODU Mounting and Alignment: Mounting ODUs to a pole or wall, performing link alignment and radio frequency (RF) verification. • Radio Configuration: Using MDS Series Link Manager software to install network- and site-specific parameters in the radios. • Radio Testing: Performing cable continuity checks and RF tests for links, the payload/radio overhead channel, and the management channel. The following diagram shows where installation and commissioning resides within the radio network deployment life cycle, and defines the sequence in which the processes that comprise installation and commissioning should be performed.
User Reference and Installation Guide 3-5 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 03-01-013bCustomerRequirementsRF Planning& NetworkDesignSite Selection& AcquisitionInstallation &CommissioningNetworkOperation &MaintenanceNetworkUpgrade &ExpansionInstall CablesMount and AlignODUsPerform SiteEvaluationConfigure DigitalSoftware DefinedIDUTMPerform FastPDH Network TestPerformSDH Network TestType ofNetwork?Installation &CommissioningCompletePDH SDHNetwork Life Cycle 3.6 Site Evaluation A site evaluation consists of a series of procedures for gathering specific information about potential radio locations. This information is critical to the successful design and deployment of a network. Site evaluations are required to confirm whether or not a building meets network design requirements. The main objectives are as follows:
User Reference and Installation Guide 3-6 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A • Confirm • Line of sight for each link • ODU mounting locations • Site equipment locations • Cable routes • Any other potential RF sources • Prepare site drawings and record site information 3.6.1 Preparing for a Site Evaluation The following tools are required to perform a site evaluation: • RF and network design diagrams (as required) • Binoculars • Global positioning system (GPS) or range finder • Compass • Measuring tape and/or wheel • Digital camera • Area map • Aerial photograph (if available) • List of potential installation sites (“targeted buildings”) The following tasks must be completed prior to performing a site evaluation: • Prepare the initial network design by performing the following: • Identify potential buildings by identifying targeted customers (applicable if you’re a service provider) • Identify potential links by selecting buildings based on the high probability of line of sight • Arrange for access with the facility personnel into the buildings, equipment rooms, and architectural plans to become familiar with the location of all ducts, risers, etc.
User Reference and Installation Guide 3-7 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3.6.2 Site Evaluation Process The following steps must be completed to perform a successful site evaluation. Each step in the process is detailed in the following subparagraphs: • Ensure RF Safety compliance: Ensure that appropriate warning signs are properly placed and posted at the equipment site or access entry. For a complete list of warnings, refer the Safety Precautions listed at the beginning of this manual. • Ensure Compliance with Laws, Regulations, Codes, and Agreements: Ensure that any installation performed as a result of the site evaluation is in full compliance with applicable federal and local laws, regulations, electrical codes, building codes, and fire codes. • Establish Radio Line of Sight between radios: The most critical step in conducting a site evaluation is confirming a clear visual and radio Line of Sight (LOS) between a near radio and a far radio. If LOS does not exist, another location must be used. Radios used in a link must have a clear view of each other, or visual “line of sight”. Binoculars may be used evaluate the path from the desired location of the near radio to the desired location of the far unit. To confirm Line of Sight: - Ensure that no obstructions are close to the transmitting/receiving path. Take into consideration trees, bridges, construction of new buildings, unexpected aerial traffic, window washing units, etc. - Ensure that each ODU can be mounted in the position required to correctly align it with its link partner. The radios must also have a clear radio line of sight. If a hard object, such as a mountain ridge or building, is too close to the signal path, it can damage the radio signal or reduce its strength. This happens even though the obstacle does not obscure the direct, visual line of sight. The Fresnel zone for a radio beam is an elliptical area immediately surrounding the visual path. It varies in thickness depending on the length of the signal path and the frequency of the signal. The necessary clearance for the Fresnel zone can be calculated, and it must be taken into account when designing a wireless links. As shown in the picture above, when a hard object protrudes into the signal path within the Fresnel zone, knife-edge diffraction can deflect part of the signal and cause it to reach the receiving antenna slightly later than the direct signal. Since these deflected signals are out of phase with the direct signal, they can reduce its power or cancel it out altogether. If trees or other 'soft' objects protrude into the Fresnel zone, they can attenuate (reduced the strength of) a passing signal. In short, the fact that you can see a
User Reference and Installation Guide 3-8 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A location does not mean that you can establish a quality radio link to that location. Microwave Data Systems provides a link planner spreadsheet that calculates the Fresnel ratio and helps determine link feasibility. Contact your technical support representative for a copy of the spreadsheet.  Determine ODU Mounting Requirements: ODUs can be mounted on an antenna mast, brick, masonry or wall. Refer to detailed installation sections. • Determine SDIDUTM Installation Location: SDIDUsTM can be installed tabletop or cabinet, wall mount, or rack mount. The site must provide DC power or an optional AC/DC converter may be used. Refer to detailed installation sections. • Document Potential Sources of Co-location Interference: When ODUs are located on a roof or pole with other transmitters and receivers, an interference analysis may be required to determine and resolve potential interference issues. The interference analysis needs to be performed by an RF engineer. The specific information required for each transmitter and receiver includes the following: - Transmitting and/or receiving frequency - Type of antenna - Distance from ODU (horizontal and vertical) - Polarity (horizontal or vertical) - Transmit power level - Antenna direction • Measure the Link Distance: The two ways to measure link distance are as follows: - GPS: record the latitude and longitude for the near and far ODU sites and calculate the link distance. Record the mapping datum used by the GPS unit and ensure the same mapping datum is used for all site evaluations in a given network. - Range finder: measure the link distance (imperial or metric units may be used). Once the link distance has been measured, verify that the link distance meets the availability requirements of the link. Microwave Data Systems has created a spreadsheet tool that calculates the link availability based on the details of the link. The Microsoft Excel spreadsheet is available on Internet, at http://www.microwavedata.com/, and is shown on the following page. The following parameters should be entered (items in yellow): • Operating Frequency: Enter 4900 • Transmit Antenna Gain: Enter the gain of the external antenna. • Transmit Output Power: Selectable between +5 to +23 dBm in 1 dB steps. • Receive Antenna Gain: Enter the gain of the external antenna if used.
User Reference and Installation Guide 3-9 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A • Link Distance: Enter distance in miles or kilometers (must select the correct units: miles or kilometers) • Fresnel Clearance Ratio: This is a factor indicating the radio line of sight. A clear radio line of site has a Fresnel clearance ratio of +0.60. As the curvature of the earth or other obstacles degrade the radio line of sight, the ratio can drop to –1. A separate spreadsheet is provided to calculate the appropriate ratio. In this spreadsheet the path length, tower heights and heights of any obstructions or ridges in the path of the link are entered. • Climate Factor: Enter 0.1 for dry, 0.25 for average and 0.5 for humid environments • Terrain Factor: Enter 0.25 for mountainous, 1 for average, and 4 for smooth (water) • Determine the Length of Interconnect Cable from ODU to SDIDUTM: The primary consideration for the outdoor interconnect cable from the ODU to SDIDUTM is the distance and route between the ODU and SDIDUTM. Maximum cable lengths are listed in 176H173HTable 3-1. Table 3-1. Maximum cable lengths Loss at (dB/100 m) Cable Type 140 MHz 350 MHz Maximum Length* LMR-200 12.6 20.1 100 m LMR-300 7.6 12.1 165 m LMR-400 4.9 7.8 256 m RG-214 8 13.1 153 m Belden 7808 8.6 14 143 m * Does not account for connector loss. The link availability, dispersive fade margin and expected signal strength readings are calculated based on the entered parameters. Maximum link distances based on the antenna and transmitter power settings are also displayed.
User Reference and Installation Guide 3-10 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A MDS FIVE series Link Planner: 5.3GHz AvailabilityParameterOperating Frequency (MHz)Transmit Antenna Gain (dBi)Transmitter Output Power (dBm)Receive Antenna Gain (dBi)Link Distance 3.93 milesFresnel Clearance Ratio1,2Climate FactorTerrain FactorMDS FIVE series Mode5.3GHz BandModem Data Rate (Mbps)Channel Bandwidth (MHz)Receiver Sensitivity3 (dBm)Link Fade Margin (dB)ODU RSSI (dBm)Availability (%)5.3G-25FE1 31.112E+6 30.0 -83 12 -71 99.99875.3G-25FE2 31.112E+6 20.0 -82 11 -71 99.99845.3G-25FE3 31.112E+6 13.3 -82 11 -71 99.99845.3G-50FE1 56.733E+6 30.0 -80 9 -71 99.99755.3G-50FE2 56.733E+6 20.0 -77 6 -71 99.99505.3G-50FE3 56.733E+6 13.3 -72 1 -71 99.98455.3G-100FE1 107.797E+6 30.0 -73 2 -71 99.98765.3G-16E1-2 36.918E+6 20.0 -82 11 -71 99.99845.3G-16T1-2 28.655E+6 20.0 -84 13 -71 99.99905.3G-16E1-3 36.918E+6 13.3 -82 11 -71 99.99845.3G-16T1-3 28.655E+6 13.3 -84 13 -71 99.9990Note1: FCC's definition; negative clearance indicates no optical LOS; range is [-1,…,0.6]; 0.6 is radio LOS condition.Note2: Accounting for single knife-edge diffraction loss only.Note3: BER<<1e-6.Note4: Listed data rates inlcudes 2 E1 Wayside channels, except for 16E1/T1 modes.(miles)99.9% 99.99% 99.999%5.3G-25FE1 QPSK 3/4 -83 9535.3G-25FE2 16QAM 3/4 -82 9535.3G-25FE3 16QAM 3/4 -82 9535.3G-50FE1 16QAM 3/4 -80 8535.3G-50FE2 32QAM 4/5 -77 7425.3G-50FE3 64QAM 11/12 -72 5325.3G-100FE1 32QAM 9/10 -73 5325.3G-16E1-2 16QAM 3/4 -82 9535.3G-16T1-2 16QAM 3/4 -84 9635.3G-16E1-3 16QAM 7/8 -82 9535.3G-16T1-3 16QAM 7/8 -84 96323for Various AvailabilityMax DistanceValue5300236MDS FIVE series ModeModulation and Code RateReceiver Sensitivity3 (dBm)0.600.251
User Reference and Installation Guide 3-11 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Path Length (Km ) 10TX Tow er Height (m ) 30RX Tow e r Height (m ) 30Fre quency (MHz) 5800Calculated Fresnel Clearance Ratio 0.48MDS FIVE series Link Planner: Fresnel Zone ClearanceDistance from TX (Km )Optical LOS Height (m )1st Fresnel Zone Radius (m )1st Fre snel Zone Height (m )Radio LOS (60% Fre snel Clearance) Zone Height (m )Earth Curvature1 (m )Obstruction Height (m )Total Earth Terrain Height (m )Fr esnel Clearance Ratio 0.0 30.0 0.0 30.0 30.0 0.0 0.0 0.0 -0.3 30.0 3.5 26.5 27.9 0.1 0.0 0.1 8.420.5 30.0 5.0 25.0 27.0 0.3 0.0 0.3 6.000.8 30.0 6.0 24.0 26.4 0.4 0.0 0.4 4.951.0 30.0 6.8 23.2 25.9 0.5 0.0 0.5 4.321.3 30.0 7.5 22.5 25.5 0.6 0.0 0.6 3.911.5 30.0 8.1 21.9 25.1 0.8 0.0 0.8 3.611.8 30.0 8.6 21.4 24.8 0.8 20.0 20.8 1.062.0 30.0 9.1 20.9 24.5 0.9 10.0 10.9 2.102.3 30.0 9.5 20.5 24.3 1.0 10.0 11.0 2.002.5 30.0 9.8 20.2 24.1 1.1 23.0 24.1 0.602.8 30.0 10.1 19.9 23.9 1.2 24.0 25.2 0.483.0 30.0 10.4 19.6 23.8 1.2 0.0 1.2 2.763.3 30.0 10.6 19.4 23.6 1.3 0.0 1.3 2.703.5 30.0 10.8 19.2 23.5 1.3 0.0 1.3 2.653.8 30.0 11.0 19.0 23.4 1.4 0.0 1.4 2.604.0 30.0 11.1 18.9 23.3 1.4 10.0 11.4 1.674.3 30.0 11.2 18.8 23.3 1.4 0.0 1.4 2.544.5 30.0 11.3 18.7 23.2 1.5 0.0 1.5 2.534.8 30.0 11.3 18.7 23.2 1.5 0.0 1.5 2.525.0 30.0 11.4 18.6 23.2 1.5 0.0 1.5 2.515.3 30.0 11.3 18.7 23.2 1.5 0.0 1.5 2.525.5 30.0 11.3 18.7 23.2 1.5 0.0 1.5 2.535.8 30.0 11.2 18.8 23.3 1.4 0.0 1.4 2.546.0 30.0 11.1 18.9 23.3 1.4 0.0 1.4 2.576.3 30.0 11.0 19.0 23.4 1.4 0.0 1.4 2.606.5 30.0 10.8 19.2 23.5 1.3 18.5 19.8 0.946.8 30.0 10.6 19.4 23.6 1.3 0.0 1.3 2.707.0 30.0 10.4 19.6 23.8 1.2 0.0 1.2 2.767.3 30.0 10.1 19.9 23.9 1.2 0.0 1.2 2.847.5 30.0 9.8 20.2 24.1 1.1 0.0 1.1 2.947.8 30.0 9.5 20.5 24.3 1.0 0.0 1.0 3.058.0 30.0 9.1 20.9 24.5 0.9 0.0 0.9 3.208.3 30.0 8.6 21.4 24.8 0.8 0.0 0.8 3.388.5 30.0 8.1 21.9 25.1 0.8 0.0 0.8 3.618.8 30.0 7.5 22.5 25.5 0.6 0.0 0.6 3.919.0 30.0 6.8 23.2 25.9 0.5 0.0 0.5 4.329.3 30.0 6.0 24.0 26.4 0.4 0.0 0.4 4.959.5 30.0 5.0 25.0 27.0 0.3 0.0 0.3 6.009.8 30.0 3.5 26.5 27.9 0.1 0.0 0.1 8.4210.0 30.0 0.0 30.0 30.0 0.0 0.0 0.0 -Note1: Earth Curvature is based on a spherical Earth model w ith a nominal radius of 6371Km and a typical K-f actor of 1.33. 0.05.010.015.020.025.030.035.00.0 2.0 4.0 6.0 8.0 10.0Di st a nc e ( k m)Opt ical LOS 1st Fr esnel Radio LOS Ear th Cur vat ure Obstr uctions
User Reference and Installation Guide 3-12 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Select the Grounding Location for both the ODU and SDIDUTM: The units must be properly grounded in order to protect them and the structure they are installed on from lightning damage. Final ODU/SDIDUTM installation requires: • Grounding all ODUs as specified by supplier • Grounding all SDIDUsTM to the rack • Confirming the Presence of DC Power for the SDIDUsTM 3.6.3 Critical System Calculations 3.6.3.1 Received Signal Level (RSL) and Link Budget The received signal level (RSL) can be estimated using the following formula: RSL (dBm) = PTX + GTX ANT – LPath + GRX ANT Where: PTX is the transmitter output power (in dBm) GTX ANT is the gain of the transmit antenna (in dB) GRX ANT is the gain of the receive antenna (in dB) LPath is the Path loss, defined by: LP (dB) = 36.6 + 20log10(F*D) Where: F is the Frequency in MHz (4900 GHz), D is the Distance of path in miles This link budget is very important in determining any potential problems during installation. The expected RSL and measured RSL should be close (+/- 5 to 10 dB) 3.6.3.2 Fade Margin Calculation The fade margin is the difference between the actual received signal and the MDS FOUR.9 Series Radio’s threshold for the modulation mode selected. The fade margin can be used to determine availability and should be at least 10 dB. 3.6.3.3 Availability Calculation Availability of the microwave path is a prediction of the percent of time that the link will operate without producing an excessive BER due to multipath fading. Availability is affected by the following: • Path length • Fade margin
User Reference and Installation Guide 3-13 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A • Frequency • Terrain (smooth, average, mountainous, valleys) • Climate (dry, temperate, hot, humid) Depending on the type of traffic carried over the link and the overall network design redundancy, fade margin should be included to support the desired availability rate. Critical data and voice may require a very high availability rate (99.999% or 4.9 minutes of predicted outage per year). To improve availability, the fade margin can be increased by shortening the path length, transmitting at a higher power level, or by using higher gain antennas. Availability can be computed using the following formula, which is known as the Vigants Barnett Method. Availability = 100 × (1 – P) P = 2.5 × 10-9 × C × F × D3× 10(-FM/10) Where F is the frequency in MHz (4900 MHz) D is the distance in miles FM is the fade margin in dB C is the climate/terrain factor as defined below: Humid/Over Water: C = 4 (worst case channel) Average Conditions: C = 1 Dry/Mountains: C = 0.25 (best case channel) Example: Assume 21 dB fade margin, over 5 miles with average climate/terrain, at 4.9 GHz. The availability comes out to be 99.9986. This corresponds to the link being unavailable for 7.6 minutes per year. 3.6.4 Frequency Plan Determination When configuring Digital Radio Series units in a point-to-point or consecutive point configuration, careful engineering should be applied in order to minimize potential interference between nearby radios. Nearby radios should operate on different frequencies, transmitting in the same band (high side or low side). When designing multi-radio configurations, antenna size, antenna polarization, and antenna location are critical. The frequency plan must be selected based on desired data rate and expected link conditions. In a high interference environment or with lower gain antennas, higher bandwidth, more robust modulation formats must be employed. The available frequency plans are illustrated in Figure 3-3. The channel assignments shown in the figures correspond to the channel numbers entered via the graphical user interface (GUI) or SNMP.
User Reference and Installation Guide 3-14 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Figure 3-3. Frequency Plans for 4.9 GHZ and 6.4 GHz Band (Pubs Note: The lower chart needs to be revised for 6.4 GHz—Greg Mills?) 3.6.5 Antenna Planning The ODU must be used with an external antenna. The choice of antenna should provide adequate link performance for most applications. Larger antennas have the advantage of providing narrower beamwidths and high isotropic gain, which yields better link performance (higher fade margin, better availability), and improves immunity to spatial interference (due to the smaller beamwidths). However, larger antennas are more costly to purchase and install than smaller antennas and in some cases, they require special equipment for installation due to narrower beamwidths. They are also more easily affected by wind.
User Reference and Installation Guide 3-15 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Only directional antennas can be used with the radios. Consult factory for antenna manufacturer options. 1. Select where the cable will enter the building from the outside. 2. Determine the length of cable required. Allow three extra feet on each end to allow for strain relief, as well as any bends and turns. 3.6.6 ODU Transmit Power Setup Setting the ODU transmit power is conditional on the band and application. The installer of this equipment is responsible for proper selection of allowable power settings. If there are any questions on power settings refer to your professional installer in order to maintain the FCC legal ERP limits. The SDIDUTM employs spectrally efficient shaped Quadrature Amplitude Modulation (QAM). This waveform is not a constant envelope waveform. Therefore, the average power and peak power are different. The difference in peak and average power depends on the constellation type and shaping factor, where spectral efficiency such as more constellation points or lower shaping factor leading to peak powers higher than average powers. The peak power is typically 5-7 dB greater than the average power in the SDIDUTM, and never exceeds 7 dB. Regulatory requirements are usually based on peak EIRP which is based on peak power and antenna gain. 3.6.6.1 4.9 GHz Band In the 4.9 GHz Public Safety band the peak EIRP (Effective Isotropic Radiated Power) is limited to +57.8 dBm at the antenna for bandwidths up to 15 MHz and is reduced for narrower bandwidths in accordance with FCC Part 90.1215. The ODU must therefore be adjusted so that the station does not exceed the allowable limit. The installer is responsible during set up of transmit power to not exceed FCC limits on transmission power. These maximum power levels are provided in Table 3-2 for various antenna configurations, along with the operational bandwidths. Note that though regulatory limits are stated in terms of peak power, the system transmit power levels are calibrated as averaged power readings. Average power is used for link calculations. Therefore the levels provided in table 3-2 are average power levels that have been certified to correspond with the maximum peak EIRP allowed. EIRP is calculated for link budget with external antennas as, EIRP(avg) dBm = External Antenna Gain (dBi) + 23 dBm 3.6.6.1.1 ODU with External Antenna When using external antennas with gains greater than 23 dBi, the transmit power must be reduced in dB from that given in Table 3-1 by the antenna gain difference above 23 dBi for the mode that is being used. For example, using a 6-foot dish antenna with 37 dBi gain, the output power would be dropped by
User Reference and Installation Guide 3-16 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Antenna Gain (External) – 23 dBi = Antenna Gain Difference 37.6 dBi – 23 dBi = 14.6 dB For mode 100FE1 (single channel configuration with 30MHz emission bandwidth) the power would be lowered from Tx Power – Antenna Gain Difference = Tx Power (External Ant) +5 dBm – 14.6 dB = -9.6 dBm (-10 dBm). Table 3-1 also presents transmit power settings for various antenna dish sizes. For link budget, EIRP (Avg) dBm = 37 dBi + Tx Power Setting (dBm). Table 3-2. Maximum Power Settings for 4.9GHz Public Safety Band Operation (US). Antenna Diameter Antenna Gain, dBi* (example) Maximum Tx Power Setting, dBm EIRP 8 foot dish 39.5 17 56.5 6 foot dish 36.1 21 57.1 4 foot dish 33.1 23 56.1 3 foot dish 30.5 23 53.5 2 foot dish 27.1 23 50.1 * Note: Many antenna manufacturers rate antenna gain in dBd (dB referred to a dipole antenna) in their literature. To convert to dBi, add 2.15 dB. Power settings for other modes of operation can be easily extrapolated from Table 3-2. For link budget calculations, EIRP (Avg) dBm= Antenna Gain (dBi) + Tx Power Setting (dBm). Though transmitter radiated power is limited in the 4.9 GHz band regardless of antenna size, the receiver benefits from gain of larger antennas. 3.6.6.2 6.4 GHz Band In the 6.4 GHz Fixed Microwave Services band the peak EIRP (Effective Isotropic Radiated Power) is limited to +55 dBw at the antenna for any bandwidths. The ODU must therefore be adjusted so that the station does not exceed the allowable limit. The installer is responsible during set up of transmit power to not exceed FCC limits on transmission power. EIRP is calculated for link budget with external antennas as,
User Reference and Installation Guide 3-17 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A EIRP (avg) dBm = External Antenna Gain (dBi) + 23 dBm For link budget calculations, EIRP (Avg) dBm= Antenna Gain (dBi) + Tx Power Setting (dBm). Though transmitter radiated power is limited in the 6.4 GHz band regardless of antenna size, the receiver benefits from gain of larger antennas. 3.6.7 Documenting a Site Evaluation Use the site evaluation form provided on the following pages to document the results of your site evaluation. Optimally, this complete site form would be stored with the SDIDUTM for future reference.
User Reference and Installation Guide 3-18 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Address Site EngineerContact PersonPhoneSite No Site AgentSite Type# Latitude LongitudeODUExample Information Information InformationODU# 4Clear Line of Sight YesMounting Method Wall or PoleFCC Compliance YesCollocationAestheticsODU Azimuth 60 degreesGPS Reading 80 21' 48"Cable LengthsAlarmInterconnect Cable 250 feetGrounding/LightingInstructionsPhotographs*Photo 1Photo 2Photo 3Sketches**Sketch 1Sketch 2*Photographs **SketchesPhoto 1 - ODU mounting location Sketch 1- Roof and cable route to entry pointPhone 2 - View from the ODU mounting location to the link partner Sketch 2 - Details for grounding and lighting protectionPhoto 3 - IDU location Sketch 3 - IDU room and cable routes from entry portSite Evaluation FormODU Roof LocationMapping Datum (ex. NDA27)Roof RequirementsRecommendations for Site Photographs and Sketches
User Reference and Installation Guide 3-19 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Site Evaluation Parameters Example Information Information Information Information Source PCS Tx and/or Rx Tx/Rx Frequency 2.1 GHz Distance from ODU 5 feet Owner Sprint PCS Azimuth 210 degrees Elevation 2 degrees downtilt Antenna Type Power Power 14W Parameters Example Information Information Information Information IDU room Identified Yes Space for cabinet Yes Phone line Need to install 48 VDC available? Yes Cables Confirm cables Take Photo 3 Sketch 3 Front View Top View Side View Equipment Cabinet Batteries NoteEquipment Dimensions Colocated SDIDUTM Indoor Space
User Reference and Installation Guide 3-20 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3.7 Installation of the Digital Radio Series The following sections provide installation guides for: • SDIDUTM Installation • ODU Installation 3.7.1 Installing the Software Defined IDUTM The SDIDUTM can be installed in the following three options: 1. Table top or cabinet 2. Wall mount 3. Rack mount The SDIDUTM should be: • Located where you can easily connect to a power supply and any other equipment used in your network, such as a router or PC. • In a relatively clean, dust-free environment that allows easy access to the rear grounding post as well as the front panel controls and indicators. Air must be able to pass freely over the chassis. • Accessible for service and troubleshooting. • Protected from rain and extremes of temperature (it is designed for indoor use). 3.7.1.1 Installing on a Table Top or Cabinet The SDIDUTM can be placed on a tabletop or cabinet shelf. In order to prevent possible disruption, it is recommended to use a strap to secure the SDIDUTM. 3.7.1.2 Installing on a Wall An installation option for the SDIDUTM is mounting the unit to a wall. If the wall mount option is being considered, plan to position the SDIDUTM at a height that allows LEDs, the connectors on the front panel, and the rear grounding post to be visible at all times and easily accessible. Also, including plastic clamps to support and arrange the ODU/ SDIDUTM Interconnect Cable should also be considered.
User Reference and Installation Guide 3-21 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3.7.1.3 Installing in a Rack To rack-mount the SDIDUTM, use the supplied mounting brackets to secure the chassis to a 19-inch rack cabinet. As shown in 179H176HFigure 3-5, the brackets can be attached to the front sides of the enclosure. An optional 21-inch rack mount kit is also available (consult factory for details). Figure 3-5. SDIDUTM Dimensions 3.7.2 Installing the ODU The ODU is intended for mounting on either a pole or antenna mast. Each site must be assessed for the mounting method, location, and height. After defining the mounting location and height for the ODU, re-confirm the line of sight. When operating a 1+1 configured SDIDU™, i.e. an SDIDU™ with two power supplies and two modem modules installed, in 1+0 mode, the ODU must be connected to the modem in the bottom slot. If the ODU is connected to the modem in the top slot, the SDIDU™ will not communicate with the ODU, and a link cannot be established. 3.7.2.1 Installing the Mounting Poles First install the mounting poles, on which you will mount the ODU. It is important to note the direction in which the ODU will point when installing the mounting pole. The mounting pole must be mounted in a vertical position. Failure to do so may result in improper alignment of the ODU. Vertical tilt of the ODU is accomplished from the tilt-mounting bracket. The mounting pole must be grounded. Now that you have installed the mounting pole, you are ready to install the ODU onto the mounting poles. Refer to80H177HFigure 3-6 through 181H178HFigure 3-9.
User Reference and Installation Guide 3-22 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Figure 3-6. Mounting Parts for the ODU 1. Remove the pole mount portion of the tilt bracket from the ODU by loosening the middle bolts and removing the top and bottom bolts on each side. 2. Mount the tilt bracket to the mounting pole using the U-Bolts and nuts. Insert the U-bolts around the pole and through the holes in the tilt bracket. Install a washer and nut to each side of the threaded U-bolt and hand tighten. Repeat this step for the second U-bolt. 3. Place the ODU on the mating half of the tilt bracket connected by the two center bolts. 4. Add the remaining four bolts to the tilt bracket and tighten securely. 5. Manually point the antenna in the direction of the link partner. Figure 3-7. ODU Rear View
User Reference and Installation Guide 3-23 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Figure 3-8. Tilt Bracket Figure 3-9. ODU with Mounted Tilt Bracket 3.7.3 Routing the ODU/ SDIDUTM Interconnect Cable 1. Select where the cable will enter the building from outside. 2. Determine the length of cable required. Allow three extra feet on each end to allow for strain relief, as well as any bends and turns.
User Reference and Installation Guide 3-24 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3. Route the cable. The SDIDUTM is equipped with TNC female connector on the front of the chassis. Depending on the ODU type, it will be equipped with either a N-type or TNC female connector at its interconnecting port. A length of coaxial cable (such as Times Microwave Systems LMR-400, LMR-300 or LMR-200) fitted with the appropriate N-type or TNC male connectors is required to connect the ODU to the SDIDUTM. This cable assembly may be supplied in fixed lengths with the digital radio. Bulk coaxial cable of equivalent specification may also be used, with terminating connectors applied during cable installation. Based on an evaluation of the cable routing path, pull the ODU/SDIDUTM Interconnect cable from one unit to the other, utilizing cable trays, ducts, or conduit as required. Take care that the ODU/ SDIDUTM Interconnect cable is not kinked or damaged in any way during installation. Be sure to protect the TNC connectors from stress, damage and contamination during installation (do not pull the cable by the connectors). If multiple ODU/ SDIDUTM Interconnect cables are to be installed along the same route, the cables should all be pulled at one time. Be sure the installed cable does not have any bends that exceed the specified cable bend radius. The ODU/ SDIDUTM Interconnect cable should be adequately supported on horizontal runs and should be restrained by hangers or ties on vertical runs to reduce stress on the cable. Outside the building, support and restrain the cable as required by routing and environmental conditions (wind, ice). The ODU/SDIDUTM and interconnection must be properly grounded in order to protect it and the structure it is installed on from lightning damage. This requires that the ODU, any mounting pole or mast and any exposed interconnect cable be grounded on the outside of the structure. The SDIDUTM must be grounded to a rack or structure ground that also has direct path to earth ground. The ODU must be directly connected to a ground rod or equivalent earth ground. The ODU/ SDIDUTM interconnect cable should also be grounded at the ODU, where the cable enters the structure and at intermediate points if the exposed cable run is long (typically at intervals of 100 ft), with the cable manufacturer’s grounding kits. Lightning protection devices used with the interconnect cable must be appropriate for the transmission of the interconnect signals (DC to 350 MHz). Provide a sufficient but not excessive length of cable at each end to allow easy connection to the ODU and SDIDUTM without stress or tension on the cable. Excessive cable length, especially outdoors, should be avoided to minimize signal attenuation and provide a more robust and reliable installation. If installing using bulk coaxial cable, terminate the ODU/ SDIDUTM Interconnect cable at each end with a TNC male connector on the SDIDUTM side and either a N-type or TNC male connector on the ODU side that is appropriate for the cable type. Use of connectors, tools and termination procedures specified by the cable manufacturer is recommended. Once the cable has been installed but before connection has been made to either unit, a simple DC continuity test should be made to verify the integrity of the installed cable. A DC continuity tester or digital multimeter may be used to verify a lack of DC continuity between the cable center conductor and outer conductor, with the opposite end of the cable unconnected. With a temporary test lead or shorting adapter connected to one end of the cable, DC continuity should be verified between the center and outer conductors at the opposite end.
User Reference and Installation Guide 3-25 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3.8 Quick Start Guide 3.8.1 Materials Required 1. Power supply (-48 V DC @ 2 Amps) OR optional AC/DC power supply and power cable (A Phoenix Contact P/N 17 86 83 1 connector is provided 2. Digital voltmeter with test leads and BNC connector (optional, for ODU alignment). 3. SDIDUTM Serial Cable (Optional) 4. Computer with networking capability, consisting of either: - Laptop computer and Ethernet card with any necessary adapters and a Cat-5 Ethernet regular or crossover cable or… - Networked computer and an additional Ethernet cable providing access to the network. The computer must meet the following system requirements: Minimum: • Pentium II 400MHz • 128MB RAM • 30MB available hard drive space • Windows 98, Windows NT, Windows 2000, or Windows XP • Internet Explorer 5.5 (available at 66H66Hhttp://www.microsoft.com) and above or Mozilla Firefox 1.0.6 (available at 67H67Hhttp://www.firefox.com) with default settings. • Sun Java JVM 1.5.0 or above (available at 68H68Hhttp://www.java.com) Recommended: • Pentium III 500MHz • 256 RAM • 30MB available hard drive space • Windows 98SE, Windows NT, Windows 2000, or Windows XP • Internet Explorer 5.5 (available at 69H69Hhttp://www.microsoft.com) and above or Mozilla Firefox 1.0.6 (available at 70H70Hhttp://www.firefox.com) with default settings. • Sun Java JVM 1.5.0 or above (available at 71H71Hhttp://www.java.com) 5. Site engineering folder with site drawings, or equivalent SDIDUTM configuration information 6. 1/8” slotted screwdriver 3.8.2 Grounding the ODU 1. Place the grounding rod so as to allow for the shortest possible path from the grounding cable to the ODU. 2. Drive the grounding rod into the ground at least eight inches from the ground surface.
User Reference and Installation Guide 3-26 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3. Attach a grounding clamp to the grounding rod. You will use this clamp to attach grounding wires for both the ODU and SDIDUTM, reference 182H179HFigure 3-10. Figure 3-10 Ground Connections to ODU 4. Connect a ground lug to one end of the grounding wire.
User Reference and Installation Guide 3-27 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 5. Remove one of the lower mounting screws of the mounting pole. Insert a screw through the grounding lug terminal and re-install it to the mounting pole. 6. Attach the grounding wire to the clamp on the grounding rod. If necessary, use wire staples to secure the grounding wire to the outside wall. 3.8.3 Grounding the SDIDUTM 1. The SDIDU™ should be able to be connected to a system or building electrical ground point (rack ground or power third-wire ground) with a cable of 36” or less. 2. Connect the grounding wire to either grounding point on the front panel. Use 6-32x5/16 maximum length screws (not provided) to fasten the lug of the grounding cable. 3. Connect the other end of the ground to the local source of ground in an appropriate manner. 3.8.4 Connecting the SDIDUTM to the PC and Power Source 1. Using the supplied power cable connector, pin 2 (labeled -V) should be connected to the power supply terminal supplying -48 V dc, while pin 1 (labeled RET) should be connected to the power supply return. Refer to 183H180HFigure 3-11. Use of a power supply with an inappropriate ground reference may cause damage to the SDIDUTM and/or the supply. Figure 3-11. SDIDUTM DC Power Cable Connector 2. Connect the SDIDUTM power cable to the -48 V dc power supply, and place the voltmeter probes on the unconnected SDIDUTM end of the power cable, with the positive voltmeter probe on pin 2 (-V) of the cable connector and the negative probe on pin 1(RET). The connector terminal screw heads may be used as convenient monitor points. Refer to 184H181HFigure 3-11. 3. Turn on the –48 V dc supply. Verify that the digital voltmeter reads between -44 V dc and -52 V dc when monitoring the cable points specified above. Adjust the power supply output voltage and/or change the connections at the power supply to achieve this reading. 4. Turn the -48 V dc supply off. 5. Plug the SDIDUTM power cable into the SDIDUTM front panel DC Power connector (DC Input). Place the voltmeter probes on the cable connector terminal screw heads as per 2 1
User Reference and Installation Guide 3-28 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A step 2 above. Refer to 185H182HFigure 3-11. Note that the SDIDUTM does not have a power on/off switch. When DC power is connected, the digital radio powers up and is operational. There can be up to 320 mW of RF power present at the antenna port. The antenna should be directed safely when power is applied. 6. Turn on the -48 V dc power supply, and verify that the reading on the digital voltmeter is as specified in step 3 above. 7. Connect the SDIDUTM to the laptop computer, using a Cat-5 Ethernet cable or connect the SDIDUTM to a computer network, using a Cat-5 Ethernet cable. Connect the Ethernet cable to the NMS 1 or 2 connector on the SDIDUTM front panel. Refer to 186H183HFigure 3-12 for the SDIDUTM front panel connections. Figure 3-12. Front Panel Connections, 1+1 Protection: SDIDUTM 3.8.5 SDIDUTM Configuration Although basic configuration of the SDIDUTM does not require a connection to the ODU, it is recommended that the ODU and SDIDUTM be connected prior to configuring the SDIDUTM. A connection to the ODU must be established prior to running the Link Configuration process (section 5.2) in order to configure ODU related parameters. 3.8.5.1 Setting the IDU IP Address 1. The PC’s network configuration must be set with the parameters provided at the end of this guide. 2. The IDU should be accessible from your PC at the default IP address provided at the end of this guide. A network ‘ping’ can be done to verify connectivity to the IDU. 3. Start web browser and use the SDIDUTM default IP address as the URL. 4. Log in at the login prompt. The username and password are provided at the end of this guide.
User Reference and Installation Guide 3-29 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 5. The GUI includes a navigation menu in the left frame. If this navigation menu is not visible, make sure the Java environment is properly installed and active. In the navigation menu, select Administration, then Network Configuration, and then General. The IP address, IP Netmask, and IP Gateway are shown. 6. Enter the new IP address, IP Netmask, and IP Gateway. The gateway must be in the same subnet as the IP address for proper operation. Click “Update” to change the values. 7. To verify the new IP address, change the PC's network configuration to be on the same subnet as the new IP address set in the unit and a network 'ping' may be performed to the new address. 8. To continue using the GUI, point the web browser to the new IP address. 3.8.5.2 Link Configuration 1. Start the SDIDUTM GUI. 2. Use the frame on the left side of the window to navigate to “Link Configuration”, then “Radio Link.” 3. Select the subcategory “Link Configuration.” 4. Select the operating mode. If the SDIDUTM has one modem installed and is connected to one ODU, select standard. If the SDIDUTM has two modems installed and is connected to two ODUs, select 1+1 diversity or 1+1 non-diversity for a protected link or east-west for a 2+0 ring configuration. 5. Follow the wizard located here to enter the rest of the required settings. 3.8.5.3 Setting SDIDUTM Site Attributes 1. Start the SDIDUTM GUI. 2. In the navigation menu, select Administration, then Device Information, and then Device Names. 3. Enter the Owner, Contact, Description, and Location. These values are not required for operation, but will help keep a system organized. 3.8.5.4 CLI Access via NMS Ethernet The CLI may be accessed via NMS Ethernet after connecting and configuring the PC as described in the previous section. Then using a Telnet client, telnet to the SDIDUTM IP address. You will be prompted for a username and password. Use the username and password supplied at the end of this guide.
User Reference and Installation Guide 3-30 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3.8.5.5 CLI Access via Serial Port The CLI for configuring/monitoring the SDIDUTM may be accessed via the front-panel serial port. 187H184HTable 3-3 shows the pinout for constructing a DB-9 to HD-15 cable. Table 3-3: Serial Cable Pinout DB-9 Pin HDB-15 Pin 2 2 3 3 5 5 The serial port parameters are show in 188H185HTable 3-4. Table 3-4: Serial Port Parameters Parameter Value Speed 38400 Bits 8 Stop-Bits 1 Parity None Flow-Control None After powering-on the SDIDUTM, the CLI may be accessed by connecting the serial cable between the PC and the SDIDUTM, launching and configuring a terminal program (e.g. HyperTerminal) and pressing the enter key. You will be prompted for a username and password, which are supplied at the end of this guide. 3.8.6 ODU Antenna Alignment To use the built-in tuning of the ODU antenna, a complete link is required, with both ends of the link roughly pointed at each other, and transmitting. Once the links are roughly pointed, connect the voltmeter to the RSSI (Receive Signal Strength Indication) BNC connector seen on the ODU. This mode outputs 0 to +3 Volts. Adjust the antenna for maximum voltage. The RSSI voltage is linearly calibrated from 2.5 Volts for maximum RSL (received signal level) at –20 dBm to 0Volts for minimum RSL at -90 dBm. This mapping characteristic is plotted below in 189H186HFigure 3-13.
User Reference and Installation Guide 3-31 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A RSSI - Mapped Voltage Output0123-100 -80 -60 -40 -20 0Received Signal Level (dBm )RSSI Output (V) Figure 3-13. ODU RSSI Output vs. Received Signal. 3.8.7 Quick Start Settings PC Network Configuration The Web GUI may be accessed via NMS by connecting a CAT5 patch cable between the SDIDUTM front-panel NMS port and a PC. The PCs network interface must be configured to an open IP address within the same subnet. For the default SDIDUTM configuration, the IP address of the PC needs to be 192.168.0.x, where x (between 2 and 253) provides an available IP address. DHCP may also be used to set the PC IP address if a DHCP server is configured on the same subnet. SDIDUTM Default IP Address Parameter Value IP Address 192.168.0.1 Netmask 255.255.255.0 Gateway 192.168.0.254 After configuring the PCs network interface, a web browser may be launched and the following URL entered to access the Web GUI: http://192.168.0.1/ Username and Password A dialog box will show requesting a username and password: • User: administrator • Pass: d1scovery
User Reference and Installation Guide 3-32 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 3.9 Documenting MDS FOUR.9 Series Configuration Use the configuration form provided at the end of this section, or a similar form, to document the results of the SDIDUTM configuration procedure. Ideally, this complete site form would be stored with the SDIDUTM for future reference.
AB-Full Access Digital Radio Configuration Form Link IDRadio Type (A/B) A=Low band, Horizontal polarization, odd serial numberB=High band & Vertical polarization, even serial numberRadio ID # Radio S/NSite NameAddresses Commissioning:Near IP: Far IP Rain ModelRouting Frequency TX RXNet Mask: IP EMS 1 Grade of ServiceNTP: IP EMS 2 Rain RegionGateway: IP EMS 3IP EMS 4 Link Distance GPS LocationSNMP Community Names Near Latitude deg min secTrap: Super User OR Near Longitude deg min secRead/Write Read: Far Latitude deg min secFar Longitude deg min secRadio Type (A/B)Radio ID# Radio S/NSite Name Addresses Commissioning:Near IP: Far IP Rain ModelRouting Frequency TX RXNet Mask: IP EMS 1 Grade of ServiceNTP: IP EMS 2 Rain RegionGateway: IP EMS 3IP EMS 4 Link Distance GPS LocationSNMP Community Names Near Latitude deg min secTrap: Super User OR Near Longitude deg min secRead/Write Read: Far Latitude deg min secFar Longitude deg min secDistance (meters)Network Administration - RadioDistance (meters)Link Administration - Radio12Network Administration - IFULink Administration - Radio
© 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 4 Summary Specifications Parameter Characteristic System Capacity 50 Mbps Ethernet 1-16 T1/E1 Various combinations of above Frequency Range 4.9475 to 4.9825 GHz Output Power – Average* (At antenna port) +5 to 23 dBm Output Power – Peak* (At antenna port) 17.1 dBm (Low Power) 24.4 dBm (High Power) Input Sensitivity -84 dBm (or higher, based on selected mode) Maximum Input Power -20 dBm Modulation Up to 64-QAM Channelization 12.5, 16.7 MHz Radio Interfaces External Antenna N Type Female SDIDUTM /ODU Link TNC Female RSSI BNC Female Data Interfaces Payload Ethernet 2 T1/E1 14 T1/E1 100Base-Tx RJ-45 RJ-48C Female (2) Molex High-Density 60-pin SNMP 10Base-T/100Base-Tx RJ-45 Female Control Network Management SNMP, web/http browser NMS Connector 10Base-T/100Base-Tx Voice Orderwire RJ-48C Auxiliary Data (64 kbps) RJ-48C
User Reference and Installation Guide 4-2 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Encryption Proprietary, AES (optional) Alarm Port 2 Form C (SPDT), 2 TTL Output, 4 TTL Input, DB-15HD Power/Environment DC Power -48 Volts +/-10%, <70 W SDIDUTM Operational Temperature -5 to 55 degrees C ODU Operational Temperature -30 to 55 degrees C SDIDUTM Humidity 0 to 95%, non-condensing ODU Humidity ODU Humidity Altitude Altitude Physical Dimensions SDIDUTM Size (WxHxD) 17.2 x 1.75 x 14.5 inches (43.7 x 4.5 x 36.0 cm) SDIDUTM Weight 7 lbs (3.12 Kg) SDIDUTM EIA Rack Mount 19 inch/48.2 cm, 1 rack unit ODU Size (W x H x D) 14.6 x 15.4 x 2.6 inches ODU Weight 15 lbs (6.8 Kgs) ODU Mounting/Installation Custom Bracket * For definitions of peak and average power, see Section 3.6.6
© 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 5 Front Panel Connectors 5.1 DC Input (Power) Connector PIN TYPE SIGNAL 1 POWER Power supply return 2 POWER -48 Vdc, nominal Two-pin male 1 2 5.2 Ethernet 100BaseTX Payload Connector 1-2 PIN TYPE SIGNAL 1 INPUT RX+ 2 INPUT RX- 3 OUTPUT TX+ 4 N/A N/A 5 N/A N/A RJ-45 Female 12 3 4 5 6 7 8 6 OUTPUT TX- 7 N/A N/A 8 N/A N/A
User Reference and Installation Guide 5-2 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 5.3 SONET Payload Connector Consult factor for Mini-IO Optical Module for availability. PIN TYPE SIGNAL OUT OUTPUT SONET OC-3 payload output (optical) IN INPUT SONET OC-3 payload input (optical) SC Duplex Female Fiber INOUT 5.4 STM-1 Payload Connector Consult factor for Mini-IO Optical Module for availability. PIN TYPE SIGNAL TX OUTPUT SDH STM-1 payload output (electrical) RX INPUT SDH STM-1 payload input (electrical) BNC Duplex RXTX 5.5 DS-3/E-3/STS-1 Payload Connector PIN TYPE SIGNAL TX OUTPUT DS-3/E-3/STS-1 payload output RX INPUT DS-3/E-3/STS-1 payload input BNC Duplex RXTX
User Reference and Installation Guide 5-3 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 5.6 NMS 10/100BaseTX Connector 1-2 PIN TYPE SIGNAL 1 OUTPUT TX+ 2 OUTPUT TX- 3 INPUT RX+ 4 N/A N/A RJ-45 Female 12 3 4 5 6 7 8 5 N/A N/A 6 INPUT RX- 7 N/A N/A 8 N/A N/A 5.7 Alarm/Serial Port Connector PIN TYPE SIGNAL 1 OUTPUT TTL Alarm Output 3 20F0F1 INPUT/ Output RS-232 RX/TX 31 OUTPUT/ Input RS-232 TX/RX DB-15HD Female 4 OUTPUT TTL Alarm Output 4 5 N/A GROUND 61F1F2 N/A Alarm 1 Form C Contact Normally Open 72 N/A Alarm 1 Form C Contact Normally Closed 82 N/A Alarm 2 Form C Contact Common 1 Pins 2 and 3 are hardware jumper configurable for DCE or DTE operation. 2 Form C Contacts are hardware jumper configurable to emulate TTL outputs.
User Reference and Installation Guide 5-4 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A PIN TYPE SIGNAL 9 INPUT TTL Alarm Input 1 10 INPUT TTL Alarm Input 3 112 N/A Alarm 1 Form C Contact Common 122 N/A Alarm 2 Form C Contact Normally Open 132 N/A Alarm 2 Form C Contact Normally Closed 14 INPUT TTL Alarm Input 2 15 Input TTL Alarm Input 4 5.8 ODU Connector PIN TYPE SIGNAL Center I/O 350 MHz TX IF / 140 MHz RX IF / -48 VDC Shield N/A Shield / Chassis GND TNC coaxial female 5.9 T1- Channels 1-2 Connector PIN TYPE SIGNAL 1 INPUT RX+ 2 INPUT RX- 3 N/A GND 4 OUTPUT TX+ RJ-45 Female 12 3 4 5 6 7 8 5 OUTPUT TX- 6 N/A GND 7 N/A N/A 8 N/A N/A
User Reference and Installation Guide 5-5 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 5.10 T1- Channels 3-16 Connector PIN TYPE SIGNAL 1 OUTPUT T1 Channel 13 Transmit Tip 2 OUTPUT T1 Channel 14 Transmit Tip 3 OUTPUT T1 Channel 15 Transmit Tip 60-pin Molex 4 OUTPUT T1 Channel 16 Transmit Tip 5 OUTPUT T1 Channel 9 Transmit Tip 6 OUTPUT T1 Channel 10 Transmit Tip 7 OUTPUT T1 Channel 11 Transmit Tip 8 OUTPUT T1 Channel 12 Transmit Tip 9 OUTPUT T1 Channel 5 Transmit Tip 10 OUTPUT T1 Channel 6 Transmit Tip 11 OUTPUT T1 Channel 7 Transmit Tip 12 OUTPUT T1 Channel 8 Transmit Tip 13 OUTPUT T1 Channel 3 Transmit Tip 14 OUTPUT T1 Channel 4 Transmit Tip 15 NC NC 16 NC NC 17 OUTPUT T1 Channel 4 Transmit Ring 18 OUTPUT T1 Channel 3 Transmit Ring 19 OUTPUT T1 Channel 8 Transmit Ring 20 OUTPUT T1 Channel 7 Transmit Ring 21 OUTPUT T1 Channel 6 Transmit Ring 22 OUTPUT T1 Channel 5 Transmit Ring 23 OUTPUT T1 Channel 12 Transmit Ring
User Reference and Installation Guide 5-6 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A PIN TYPE SIGNAL 24 OUTPUT T1 Channel 11 Transmit Ring 25 OUTPUT T1 Channel 10 Transmit Ring 26 OUTPUT T1 Channel 9 Transmit Ring 27 OUTPUT T1 Channel 16 Transmit Ring 28 OUTPUT T1 Channel 15 Transmit Ring 29 OUTPUT T1 Channel 14 Transmit Ring 30 OUTPUT T1 Channel 13 Transmit Ring 31 INPUT T1 Channel 16 Receive Tip 32 INPUT T1 Channel 15 Receive Tip 33 INPUT T1 Channel 9 Receive Tip 34 INPUT T1 Channel 14 Receive Tip 35 INPUT T1 Channel 10 Receive Tip 36 INPUT T1 Channel 13 Receive Tip 37 INPUT T1 Channel 11 Receive Tip 38 INPUT T1 Channel 4 Receive Tip 39 INPUT T1 Channel 12 Receive Tip 40 INPUT T1 Channel 3 Receive Tip 41 INPUT T1 Channel 5 Receive Tip 42 INPUT T1 Channel 8 Receive Tip 43 INPUT T1 Channel 6 Receive Tip 44 INPUT T1 Channel 7 Receive Tip 45 NC NC 46 NC NC 47 INPUT T1 Channel 7 Receive Ring 48 INPUT T1 Channel 6 Receive Ring
User Reference and Installation Guide 5-7 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A PIN TYPE SIGNAL 49 INPUT T1 Channel 8 Receive Ring 50 INPUT T1 Channel 5 Receive Ring 51 INPUT T1 Channel 3 Receive Ring 52 INPUT T1 Channel 12 Receive Ring 53 INPUT T1 Channel 4 Receive Ring 54 INPUT T1 Channel 11 Receive Ring 55 INPUT T1 Channel 13 Receive Ring 56 INPUT T1 Channel 10 Receive Ring 57 INPUT T1 Channel 14 Receive Ring 58 INPUT T1 Channel 9 Receive Ring 59 INPUT T1 Channel 15 Receive Ring 60 INPUT T1 Channel 16 Receive Ring 5.11 USB PIN TYPE SIGNAL 1 OUTPUT +5V 2 I/O -Data 3 I/O +Data USB Type A 4 N/A GND
User Reference and Installation Guide 5-8 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 5.12 Voice Order Wire PIN TYPE SIGNAL 1 N/A NC 2 INPUT PTT 3 N/A GND 4 OUTPUT PO- RJ-48C Female 12 3 4 5 6 7 8 5 OUTPUT PO+ 6 INPUT TI- 7 N/A GND 8 N/A NC 5.13 Data Order Wire PIN TYPE SIGNAL 1 OUTPUT TX Clock - 2 OUTPUT TX Clock + 3 OUTPUT TX Data - 4 INPUT RX Data - RJ-48C Female 12 3 4 5 6 7 8 5 INPUT RX Data + 6 OUTPUT TX Data + 7 INPUT RX Clock - 8 INPUT RX Clock +
© 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A 6 Appendix 6.1 Alarm Descriptions Alarm Affected Component Description LED to RED Alarm Code Severity Modem Fault Lower Modem The specified Modem card has indicated a fault. Fault detection is via reading Modem Hardware Status from MODEM during start-up and polling GPIO for MODEM fault indication. Polling interval 5 sec. N/A 11 Critical Modem Comm. Failure Lower Modem The Controller Card is unable to communicate with the specified Modem card. Modem Lower 12 Critical Modem Card Removed Lower Modem The specified Modem card has been removed from the IDU (only if the specified Modem card has been enabled for use). Fault detection via card-detect logic. N/A 13 Major Modem Card Installed Lower Modem The specified Modem card has been installed into the IDU (only if the specified Modem card is not enabled for use). Fault detection via card-detect logic. Alarm is cleared after 5 minutes. Modem Lower 14 Info Modem Unlock Lower Modem The demodulation functional components of the modem have lost lock to the incoming signal. The data received through the RF link is not valid. Fault detection via modem status polling. Polling interval: 1 sec. N/A N/A Critical
User Reference and Installation Guide 6-2 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity RSL Low Lower Modem RSSI is approaching the minimum operational level of the link as set during configuration. Fault detection via modem status polling, comparing RSSI value to threshold value in configuration table. Polling interval 5 sec. N/A N/A Major Synthesizer Unlock Lower Modem Modem synthesizer has unlocked. Fault detection via modem status polling. Polling is done in conjunction with Modem Unlock polling. N/A N/A Critical SNR Low Lower Modem The signal-to-noise ratio is below the minimum operational level of the link as set during configuration. Fault detection via modem status polling, comparing Eb/N0 value to threshold value in configuration table. Polling interval 5 sec. N/A N/A Major Modem Fault Upper Modem The specified Modem card has indicated a fault. Fault detection is via reading Modem Hardware Status from MODEM during start-up and polling GPIO for MODEM fault indication. Polling interval 5 sec. N/A 16 Critical Modem Comm. Failure Upper Modem The Controller Card is unable to communicate with the specified Modem card. Modem Lower 17 Critical Modem Card Removed Upper Modem The specified Modem card has been removed from the IDU (only if the specified Modem card has been enabled for use). Fault detection via card-detect logic. N/A 18 Major
User Reference and Installation Guide 6-3 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity Modem Card Installed Upper Modem The specified Modem card has been installed into the IDU (only if the specified Modem card is not enabled for use). Fault detection via card-detect logic. Alarm is cleared after 5 minutes. Modem Upper 19 Info Modem Unlock Upper Modem The demodulation functional components of the modem have lost lock to the incoming signal. The data received through the RF link is not valid. Fault detection via modem status polling. Polling interval 1 sec. N/A N/A Critical RSL Low Upper Modem RSSI is approaching the minimum operational level of the link as set during configuration. Fault detection via modem status polling, comparing RSSI value to threshold value in configuration table. Polling interval 5 sec. N/A N/A Major SNR Low Upper Modem The signal-to-noise ratio is below the minimum operational level of the link as set during configuration. Fault detection via modem status polling, comparing Eb/N0 value to threshold value in configuration table. Polling interval 5 sec. N/A N/A Major Synthesizer Unlock Upper Modem Modem synthesizer has unlocked. Fault detection via modem status polling. Polling is done in conjunction with Modem Unlock polling. N/A N/A Critical Fan Failure Controller The Fan rotational speed is too low. (Controller card LED flashed red rather than orange). Fault detection via polling fan controller status. Polling interval 10 sec. Controller 21 Critical
User Reference and Installation Guide 6-4 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity Controller Card Fault Controller The CPU has detected a fault in the controller card. (Controller card LED flashes red rather than orange). Fault detection via software. Controller 22 Critical Low Battery Voltage Controller The CPU has detected a low-battery voltage condition. (Controller card LED flashes red rather than orange). Fault detection via software polling RTC via controller FPGA. Controller 23 Info Power Supply Fault Lower Power Supply The Power Supply card has indicated a fault. Fault detection via polling GPIO. Polling interval 5 sec. N/A 31 Critical Power Supply Card Removed Lower Power Supply The specified Power Supply card has been removed from the IDU. Fault detection via card-detect logic. N/A 32 Major Power Supply Fault Upper Power Supply The Power Supply card has indicated a fault. Fault detection via polling GPIO. Polling interval 5 sec. N/A 36 Critical Power Supply Card Removed Upper Power Supply The specified Power Supply card has been removed from the IDU. Fault detection via card-detect logic. N/A 37 Major Standard I/O Card Removed StdIO The Standard I/O card has been removed from the IDU. Fault detect via card-detect logic. N/A 41 Critical Ethernet Payload Disconnect StdIO There is no cable detected at either Ethernet payload on Standard I/O card (only if Ethernet mode enabled). Fault detection via polling of Ethernet PHY. Polling interval 5 sec. Standard I/O 42 Critical
User Reference and Installation Guide 6-5 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity Framer Initialization Timeout StdIO There is an Initialization wait for Framer to turn ON the Framer Receiver side after turning ON the Modem/ODU. Fault detection via polling. Poll only after timeout to detect. Standard I/O 43 Critical Mini I/O Card Removed MiniIO The Mini I/O card has been removed from the IDU (only if Mini I/O card has been enabled for use). Fault detection via card-detect logic. Standard I/O 46 Critical Mini I/O Card Installed MiniIO The Mini I/O card has been installed into the IDU (only if Mini I/O card is noted enabled for use). Fault detection via card-detect logic. Alarm is cleared after 5 minutes. Standard I/O 47 Info Optional I/O Card Removed OptIO The Optional I/O card has been removed from the IDU (only if the Optional I/O card has been enabled for use). Fault detection via card-detect logic. N/A 26 Critical Optional I/O Card Installed OptIO The Optional I/O card has been installed into the IDU (only if the Optional I/O card is not enabled for use). Fault detection via card-detect logic. Alarm is cleared after 5 minutes. Optional I/O 27 Info
User Reference and Installation Guide 6-6 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity T1/E1 Channel Alarm Ch x StdIO (1-16) OptIO (17-32) There is either no cable detected at the specified E1/T1 channel port on Standard I/O Card or there is an AIS condition detected (only for active T1/E1 channels). Fault detection via polling of LIUs on Standard I/O card and Optional I/O Card when installed. Polling interval 2 channels per 1 sec. Report of this alarm in the GUI/Syslog/Alarm history shall indicate whether this is a disconnect or AIS condition. Standard I/O when 1-16 Optional I/O when 17-32 Turn LED orange rather than RED 51-58 (1-16) 61-68 (17-32) Critical T1/E1 Test Mode StdIO The user has selected a T1/E1 test mode (loopback or Tx Data). This alarm shall be set when the user sets the test mode for any of the T1/E1 channels, and cleared when all T1/E1 channels are not in loopback and Tx Data is normal. N/A 59 Info BERT/LB/CW Test Mode StdIO This alarm shall be set when the user enables either BERT, Loopback, or CW mode, and cleared when all BERT, Loopback and CW modes are disabled. N/A 69 Info ODU Fault Lower ODU The ODU has indicated a fault condition. Fault detection via polling of ODU or unsolicited message, if supported. Polling interval 5 sec. Polling done via API functional call. Report of this alarm in the GUI/Syslog/Alarm history shall indicate the fault code from the ODU. N/A 71 Critical ODU Comm. Failure Lower ODU The IDU is unable to communicate with the ODU. This could be a problem with the ODU or a problem with the cable connecting the ODU to the IDU. N/A 72 Critical
User Reference and Installation Guide 6-7 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity ODU Fault Upper ODU The ODU has indicated a fault condition or unsolicited message, if supported. Fault detection via polling of ODU. Polling interval 5 sec. Polling done via API function call. Report of this alarm in the GUI/Syslog/Alarm history shall indicate the fault code from the ODU. N/A 73 Critical ODU Comm. Failure Upper ODU The IDU is unable to communicate with the ODU. This could be a problem with the ODU or a problem with the cable connecting the ODU to the IDU. N/A 74 Critical Protection Switch MODEM/ODU This alarm shall be set when an AL1 command is received from the active MODEM/ODU, and then cleared when an AL2 command is received from the standby MODEM/ODU. Report of this alarm in the GUI/Syslog/Alarm history shall indicate the fault code from the ODU, if received. N/A 75 Critical East ATPC Tx at Max Power ODU The IDU is unable to increase the Tx Power as requested by link partner due to maximum power being reached. Maximum power is specified in the configuration table. N/A 76 Info West ATPC Tx at Max Power ODU The IDU is unable to increase the Tx Power as requested by link partner due to maximum power being reached. Maximum power is specified in the configuration table. N/A 78 Info Link Fault IDU Failed to receive link heartbeat from link partner via Radio Overhead (ROH) channel. Fault detection via timeout counter, which is reset via reception of link heartbeat message. N/A 81 Critical
User Reference and Installation Guide 6-8 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity Remote Fault IDU Link Partner IDU indicating it has a fault condition. Local IDU receives Link Partner Fault detection via Radio Overhead (ROH) channel message. N/A 82 Info Encryption Failure IDU Data is not being decrypted properly due to encryption key mismatch between link partners. Fault detection via software detection of unreadable ROH messages from link partner. N/A 83 Critical Encryption One Way IDU Only one IDU has data encryption enabled. Fault detection via software messages to/from link partner. N/A 84 Major External Alarm 1 External The external Alarm 1 input has been activated. Fault detection via polling GPIO. Polling interval 1 sec. N/A 91 Info External Alarm 2 External The external Alarm 2 input has been activated. Fault detection via polling GPIO. Polling interval 1 sec. N/A 92 Info External Alarm 3 External The external Alarm 3 input has been activated. Fault detection via polling GPIO. Polling interval 1 sec. N/A 93 Info External Alarm 4 External The external Alarm 4 input has been activated. Fault detection via polling GPIO. Polling interval 1 sec. N/A 94 Info Remote IDU Alarm Link Partner IDU The link partner IDU has indicated an alarm condition via ROH. N/A 95 Major Remote IDU External Alarm 1 Link Partner External The link partner IDU has indicated via ROH its external alarm input 1 has been activated. N/A 96 Info
User Reference and Installation Guide 6-9 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity Remote IDU External Alarm 2 Link Partner External The link partner IDU has indicated via ROH its external alarm input 2 has been activated. N/A 97 Info Remote IDU External Alarm 3 Link Partner External The link partner IDU has indicated via ROH its external alarm input 3 has been activated. N/A 98 Info Remote IDU External Alarm 4 Link Partner External The link partner IDU has indicated via ROH its external alarm input 4 has been activated. N/A 99 Info STM Loss of Clock IDU The SDH/SONET clock has lost lock. Fault detection via polling of LIU. N/A Solid Critical STM RS_LOS IDU The SDH/SONET has a Loss of Signal Defect. Fault detection via polling of LIU. N/A Solid Critical STM RS_B1 IDU The SDH/SONET Mux/Demux has a B1 Defect. Fault detection via polling of RS_B1_T bit in STM-1 Core. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major STM RS_LOF IDU The SDH/SONET Mux/Demux has a Loss of Frame Defect. Fault detection via polling of RS_LOF_T bit in STM-1 Core. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM RS_OOF IDU The SDH/SONET Mux/Demux has an Out of Frame Defect. Fault detection via polling of RS_OOF_T bit in STM-1 Core. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical
User Reference and Installation Guide 6-10 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity STM RS_TIM IDU The SDH/SONET Mux/Demux has a Trace Identifier Mismatch Defect. Fault detection via polling of RS_TIM_T bit in STM-1 Core. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major STM MS-AIS IDU The SDH/SONET Mux/Demux has detected an AIS at the Multiplexer Level. Fault detection via polling of MS_AIS_T bit in STM-1 Core. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM MS-REI IDU The SDH/SONET Mux/Demux has detected a Remote Error at the Multiplexer Level. Fault detection via polling of MS_REI_T bit in STM-1 Core. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major STM MS-RDI IDU The SDH/SONET Mux/Demux has detected a Remote Defect at the Multiplexer Level. Fault detection via polling of MS_RDI_T bit in STM-1 Core. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major STM MS_B2 IDU The SDH/SONET Mux/Demux has a B2 Defect at the Multiplex level. Fault detection via polling of MS_B2_T bit in STM-1 Core. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major STM AU-AIS x IDU The SDH/SONET Mux/Demux has detected an AIS at the AU Level. Fault detection via polling of AU_AIS_T bit in STM-1 Core. Where ‘x’ is the HP index. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical
User Reference and Installation Guide 6-11 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity STM AU-LOP x IDU The SDH/SONET Mux/Demux has detected a Loss of Pointer Defect at the AU Level. Fault detection via polling of AU_LOP_T bit in STM-1 Core. Where ‘x’ is the HP index. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM HP-UNEQ x IDU The SDH/SONET Mux/Demux HP number ‘x’ is Unequipped. Fault detection via polling of HP_UNEQ_T bit in STM-1 Core. Where ‘x’ is the HP index. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM HP-TIM x IDU The SDH/SONET Mux/Demux HP number ‘x’ has a Trace Identifier Mismatch. Fault detection via polling of HP_TM_TIM_T bit in STM-1 Core. Where ‘x’ is the HP index. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major STM HP-REI x IDU The SDH/SONET Mux/Demux HP number ‘x’ has a Remote Error Indication. Fault detection via polling of HP_REI_T bit in STM-1 Core. Where ‘x’ is the HP index. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM HP-RDI x IDU The SDH/SONET Mux/Demux HP number ‘x’ has a Remote Defect Indication. Fault detection via polling of HP_RDI_T bit in STM-1 Core. Where ‘x’ is the HP index. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical
User Reference and Installation Guide 6-12 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity STM HP-PLM x IDU The SDH/SONET Mux/Demux HP number ‘x’ has a Path Identifier Mismatch. Fault detection via polling of HP_PLM_T bit in STM-1 Core. Where ‘x’ is the HP index. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM HP_B3 x IDU The SDH/SONET Mux/Demux HP number ‘x’ has a CRC Error. Fault detection via polling of HP_B3_T bit in STM-1 Core. Where ‘x’ is the HP index. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major STM TU-LOM lkm IDU The SDH/SONET Mux/Demux TU number ‘x’ has a Loss of Multiframe. Fault detection via polling of TU_LOMF_T bit in STM-1 Core. Where ‘lkm’ is the TU index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM TU-AIS lkm IDU The SDH/SONET Mux/Demux TU number ‘x’ has an AIS. Fault detection via polling of TU_AIS_T bit in STM-1 Core. Where ‘lkm’ is the TU index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM TU-LOP lkm IDU The SDH/SONET Mux/Demux TU number ‘x’ has a Loss of Pointer Defect. Fault detection via polling of TU_LOP_T bit in STM-1 Core. Where ‘lkm’ is the TU index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical
User Reference and Installation Guide 6-13 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity STM LP-UNEQ lkm IDU The SDH/SONET Mux/Demux LP number ‘x’ is Unequipped. Fault detection via polling of LP_UNEQ_T bit in STM-1 Core. Where ‘lkm’ is the LP index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Info STM LP-TIM lkm IDU The SDH/SONET Mux/Demux LP number ‘x’ has a Trace Identifier Mismatch. Fault detection via polling of LP_TM_TIM_T bit in STM-1 Core. Where ‘lkm’ is the LP index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major STM LP-REI lkm IDU The SDH/SONET Mux/Demux LP number ‘x’ has a Remote Error Indication. Fault detection via polling of LP_REI_T bit in STM-1 Core. Where ‘lkm’ is the LP index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM LP-RDI lkm IDU The SDH/SONET Mux/Demux LP number ‘x’ has a Remote Defect Indication. Fault detection via polling of LP_RDI_T bit in STM-1 Core. Where ‘lkm’ is the LP index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM LP-PLM lkm IDU The SDH/SONET Mux/Demux LP number ‘x’ has a Path Identifier Mismatch. Fault detection via polling of LP_PLM_T bit in STM-1 Core. Where ‘lkm’ is the LP index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical
User Reference and Installation Guide 6-14 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A Alarm Affected Component Description LED to RED Alarm Code Severity STM LP-RFI lkm IDU The SDH/SONET Mux/Demux LP number ‘x’ has a Remote Fault Indication. Fault detection via polling of LP_RFI_T bit in STM-1 Core. Where ‘lkm’ is the LP index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Critical STM LP-BIP2 lkm IDU The SDH/SONET Mux/Demux LP number ‘x’ has a CRC Error. Fault detection via polling of LP_BIP2_T bit in STM-1 Core. Where ‘lkm’ is the LP index as LKM numbering. Alternate detection via Interrupt enabled in STM-1 core. N/A Solid Major 6.2 Abbreviations & Acronyms AIS Alarm Indication Signal BER Bit Error Rate Codec Coder-Decoder CPU Central Processing Unit DB Decibel DBm Decibel relative to 1 mW DCE Data Circuit-Terminating Equipment DTE Data Terminal Equipment EIRP Effective Isotropic Radiated Power FCC Federal Communications Commission FEC Forward Error Correction FPGA Field Programmable Gate Array GPIO General Purpose Input/Output IF Intermediate frequency IP Internet Protocol LED Light-emitting diode
User Reference and Installation Guide 6-15 © 2006 Microwave Data Systems Inc. All Rights Reserved. MDS FOUR.9 Series 05-4561A01, Rev. A LOS Line of Sight MIB Management Information Base Modem Modulator-demodulator ms Millisecond NC Normally closed NMS Network Management System OAM&P Operations, Administration, Maintenance, and Provisioning OC-3 Optical Carrier level 3 ODU Outdoor Unit PCB Printed circuit board POP Point of Presence QAM Quadrature Amplitude Modulation QPSK Quadrature Phase Shift Keying RF Radio Frequency RSL Received Signal Level (in dBm) RSSI Received Signal Strength Indicator/Indication RX Receiver SDH Synchronous Digital Hierarchy SNMP Simple Network Management Protocol SNR Signal-to-Noise Ratio SDIDUTM Software Defined Indoor Unit (CarrierComm trademark) SONET Synchronous Optical Network STM-1 Synchronous Transport Module 1 TCP/IP Transmission Control Protocol/Internet Protocol TTL Transistor-transistor logic TX Transmitter
IN CASE OF DIFFICULTY... MDS products are designed for long life and trouble-free operation. However, this equipment, as with all electronic equipment, may have an occasional component failure. The following information will assist you in the event that servicing becomes necessary. TECHNICAL ASSISTANCE Technical assistance for MDS products is available from our Technical Support Department during business hours (8:00 A.M.–5:30 P.M. Eastern Time). When calling, please give the complete model number of the radio, along with a description of the trouble/symptom(s) that you are experiencing. In many cases, problems can be resolved over the telephone, without the need for returning the unit to the factory. Please use one of the following means for product assistance: Phone: 585 241-5510 E-Mail: mailto:TechSupport@microwavedata.com FAX: 585 242-8369 Web: http://www.microwavedata.com/ FACTORY SERVICE Component level repair of radio equipment is not recommended in the field. Many components are installed using surface mount technology, which requires specialized training and equipment for proper servicing. For this reason, the equipment should be returned to the factory for any PC board repairs. The factory is best equipped to diagnose, repair and align your radio to its proper operating specifications. If return of the equipment is necessary, you will be issued a Service Request Order (SRO) number and return shipping address. The SRO number will help expedite the repair so that the equipment can be repaired and returned to you as quickly as possible. Please be sure to include the SRO number on the outside of the shipping box, and on any correspondence relating to the repair. No equipment will be accepted for repair without an SRO number. A statement should accompany the radio describing, in detail, the trouble symptom(s), and a description of any associated equipment normally connected to the radio. It is also important to include the name and telephone number of a person in your organization who can be contacted if additional information is required. The radio must be properly packed for return to the factory. The original shipping container and packaging materials should be used whenever possible. When repairs have been completed, the equipment will be returned to you by the same shipping method used to send it to the factory. Please specify if you wish to make different shipping arrangements. To inquire about an in-process repair, you may contact our Product Services Group at 585-241-5540 (FAX: 585-242-8400), or via e-mail at: ProductServices@microwavedata.com
User Reference and Installation Guide 6-2

Navigation menu