GE GFK 1918D FXVersaPro User Manual To The E757f124 6f65 4350 95e4 E4d1ba01ef74
User Manual: GE GFK-1918D to the manual
Open the PDF directly: View PDF 
.
Page Count: 114
| Download | |
| Open PDF In Browser | View PDF |
Getting Started Logic Developer - PLC PLC Programming Software Version 4.00 May 2003 GFK-1918D All rights reserved. No part of this publication may be reproduced in any form or by any electronic or mechanical means, including photocopying and recording, without permission in writing from GE Fanuc Automation Americas, Inc.. Disclaimer of Warranties and Liability The information contained in this manual is believed to be accurate and reliable. However, GE Fanuc Automation Americas, Inc. assumes no responsibilities for any errors, omissions or inaccuracies whatsoever. Without limiting the foregoing, GE Fanuc Automation Americas, Inc. disclaims any and all warranties, expressed or implied, including the warranty of merchantability and fitness for a particular purpose, with respect to the information contained in this manual and the equipment or software described herein. The entire risk as to the quality and performance of such information, equipment and software, is upon the buyer or user. GE Fanuc Automation Americas, Inc. shall not be liable for any damages, including special or consequential damages, arising out of the use of such information, equipment and software, even if GE Fanuc Automation Americas, Inc. has been advised in advance of the possibility of such damages. The use of the information contained in the manual and the software described herein is subject to GE Fanuc Automation Americas, Inc. standard license agreement, which must be executed by the buyer or user before the use of such information, equipment or software. Notice GE Fanuc Automation Americas, Inc. reserves the right to make improvements to the products described in this publication at any time and without notice. © 2003 GE Fanuc Automation Americas, Inc. All rights reserved. CIMPLICITY is a registered trademark of GE Fanuc Automation. Any other trademarks referenced herein are used solely for purposes of identifying compatibility with the products of GE Fanuc Automation Americas, Inc. We want to hear from you. If you have any comments, questions, or suggestions about our documentation, send them to the following email address: doc@gefanuc.com 2 Contents 1 Welcome 1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Product Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2 CIMPLICITY Machine Edition 9 Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Projects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Machine Edition Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Companion Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 InfoViewer Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 3 GE Fanuc PLC Targets 23 Addinging, Configuring and Converting Targets . . . . . . . . . . . . . .24 Adding Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Configuring Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Converting Targets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Configuring Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Configuring Communication for PACSystems™ . . . . . . . . . . . .28 Configuring Communication for non-PACSystems™ PLCs . . . .30 Interacting with the PLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Validating a Target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Online/Offline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Upload/Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Run/Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Fault Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Reference View Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 CIMPLICITY Logic Developer - PLC Version 4.00 i 4 Hardware Configuration (HWC) 43 PACSystems™ RX7i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Configuring PACSystems™ RX7i Hardware . . . . . . . . . . . . . . 44 Redundancy (Series 90™-70 and PACSystems™ RX7i only) . . 50 Configuring Redundant Systems . . . . . . . . . . . . . . . . . . . . . . . 52 Series 90™-30: DSM314 Motion Module . . . . . . . . . . . . . . . . 55 Series 90™-70 Genius Remote I/O Scanner . . . . . . . . . . . . . . 57 VersaMax Remote I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 5 Logic Editors 63 LD Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Working with the LD Editor Offline . . . . . . . . . . . . . . . . . . . . 67 Editing Logic as Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Working with the LD Editor Online . . . . . . . . . . . . . . . . . . . . 72 Word-for-Word Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Writing Changes to a Target PLC . . . . . . . . . . . . . . . . . . . . . . 74 LD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 IL Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Working with the IL Editor Offline . . . . . . . . . . . . . . . . . . . . . 80 Working with the IL Editor Online . . . . . . . . . . . . . . . . . . . . . 82 Writing Changes to a Target PLC . . . . . . . . . . . . . . . . . . . . . . 83 IL Instructions and Functions . . . . . . . . . . . . . . . . . . . . . . . . . 84 C Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Working with C blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 C Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 User Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Working with User Programs . . . . . . . . . . . . . . . . . . . . . . . . . 89 6 Motion Programming 91 PLC Motion Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Working with the Motion Editor . . . . . . . . . . . . . . . . . . . . . . . 93 Motion Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Local Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Working with Local Logic Editor . . . . . . . . . . . . . . . . . . . . . . . 96 Local Logic Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Local Logic Commands and Operators . . . . . . . . . . . . . . . . . . 99 ii CIMPLICITY Logic Developer - PLC Version 4.00 CAM Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 Working with the CAM Editor . . . . . . . . . . . . . . . . . . . . . . . .101 CIMPLICITY Logic Developer - PLC Version 4.00 iii 1 Welcome Congratulations on your purchase of Logic Developer - PLC, the GE Fanuc PLC programming component of Machine Edition automation software. This software package provides all the tools necessary to create powerful control applications. Logic Developer - PLC provides a way to configure your PLC hardware or remote I/O, create and edit PLC logic, upload and download projects, and monitor and debug the execution of control programs. Projects can be imported from Logicmaster, VersaPro, and CimplicityControl folders. CIMPLICITY Logic Developer - PLC Version 4.00 1 1 We l c ome Logic Developer - PLC makes it possible to develop control applications on a personal computer and download them to a PLC via Ethernet or serial/modem connection. Hosted in the Machine Edition environment, Logic Developer - PLC takes advantage of a powerful set of common programming tools (see page 14). The same tools can be applied to Logic Developer - PC (PC Control), Logic Developer State, CIMPLICITY View and CIMPLICITY Motion components, providing a single programming environment. The Machine Edition environment unites and organizes components, providing data sharing and networked operation. The following features are included in this version of Logic Developer - PLC: 2 ■ Hardware Configuration (HWC): a comprehensive tool for configuring and customizing GE Fanuc PLCs or racks of Remote I/O for your specific operating needs. For more information on Hardware Configuration, see page 43. ■ LD Editor: an intelligent, cell-based, graphical editor for developing LD (Ladder Diagram) logic. You can customize the look and feel of the LD Editor. For more information on the LD Editor, see page 63. ■ IL Editor: an easy-to-use, free-form text editor for creating Instruction List logic. Configurable formatting rules and color coding make your scripts easy to read. For more information on the IL editor, see page 79. ■ C Blocks and C Programs: independent sections of executable code, written in C language, that are developed outside of Logic Developer - PLC. Precompiled C blocks and C programs are imported into your project. For more information on C blocks, see page 86. For more information on C programs, see page 88. ■ PLC Motion Editor: a free-form text editor that enables you to enter the program in your preferred style. The PLC Motion editor is specifically designed for support of the IC693DSM314 motion module. For more information on the Motion editor, see page 91. ■ Local Logic Editor: a text-based editor used for developing logic that executes locally on a IC693DSM314 motion module. Local Logic runs synchronously with the PLC Motion program, but is independent of the PLC’s CPU. For more information on the Local Logic editor, see page 95. ■ CAM Editor: an accessory for the Logic Developer - PLC Motion editor specifically designed for support of the IC693DSM314 motion module. It provides a graphical means to create, edit, and manage electronic CAM profiles. For more information on the CAM editor, see page 100. CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D We l co me System Requirements SYSTEM REQUIREMENTS To use Logic Developer - PLC and its tools, you require the following: ■ Windows® NT version 4.0 with service pack 6.0 or later OR Windows 2000 Professional OR Windows XP Professional OR Windows ME OR Windows 98 SE. GFK-1918D ■ Internet Explorer version 5.5 with Service Pack 2 or later. (You must install IE5.5 SP2 before installing Machine Edition.) ■ 500 MHz Pentium-based computer. (1 GHz recommended.) ■ 128 MB RAM (256 MB recommended). ■ TCP/IP Network protocol-based computer. ■ 150-750 MB free hard disk space depending on the selected products. ■ 200 MB hard disk space for sample projects (optional). ■ Additional hard disk space for projects and temporary files. CIMPLICITY Logic Developer - PLC Version 4.00 3 1 We l c ome Installation INSTALLATION For last-minute information, release notes, and supported hardware lists for Machine Edition products, see the Important Product Information (IPI) document on the CD. There are several ways to view this document ■ When installing Machine Edition, select Important Product Information on the initial Launcher screen. ■ From the Machine Edition Help menu, choose Important Product Information. ■ When running Machine Edition, click the InfoView tab in the Navigator, then double-click the Important Product Information page under Getting Started in the Table of Contents. ■ When running Machine Edition, click the Home button on the InfoViewer toolbar, then click the What’s New link under Get Started on the left hand side. If you have a previous version of Machine Edition installed on your workstation, you must uninstall it before installing the latest version. You can do so by selecting the “Uninstall CIMPLICITY Machine Edition” option from the CIMPLICITY Machine Edition Start menu group. All projects, settings, and authorizations will remain intact during an uninstall operation. T o ins ta ll L o gic D e ve lo p er - P LC 1. Insert the CIMPLICITY Machine Edition CD into your CD-ROM drive. By default, the setup program will automatically start. If the setup program does not automatically start, run Setup.exe in the root directory of the CD. 2. Click Install to start the install process. 3. Follow the instructions as they appear on the screen. 4 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D We l co me Product Authorization PRODUCT AUTHORIZATION Before you can start developing projects with Logic Developer - PLC, you must authorize the software with a program called Product Authorization. If you don’t authorize the software, you can use it for only a four-day trial period. This procedure takes only a few minutes and enables you to take advantage of any product support for which you qualify. You will need to contact us by telephone, fax, or e-mail as part of the authorization process. T o aut ho ri ze a c op y of Mac hi n e Ed i ti o n 1. Have your serial numbers ready. The serial numbers can be found on the License Key sheet that came with your product. 2. Run the Product Authorization program from the Start menu > Programs > Product Authorization. The Product Authorization dialog box appears. 3. Click Add. 4. Select the medium with which you are authorizing: Internet, Phone/Fax/E-mail, or Floppy Disk Transfer. Click Next. If you choose the Internet option, proceed to step 5. If you choose the Phone/ Fax/E-mail option, proceed to step 5. If you choose the Floppy Disk Transfer option, ensure you have an authorization disk before proceeding. 5. Fill in the fields in the dialog box. Fields that are identified with an asterisk (*) must be filled in. 6. If authorizing by: ■ Internet, click Submit Authorization. We will reply by e-mail with your new key code(s). ■ Phone, click Phone/Fax and call the number on the screen to receive a new key code(s). ■ Fax, click Phone/Fax. In the dialog box that appears, click Print FAX. Fax the Product Authorization Request to us, using our fax number on the printout. We will reply by fax with your new key code(s). ■ E-mail, click Send E-mail. In the dialog box that appears, click Authorize to email us. We will reply by e-mail with your new key code(s). Product Authorization is complete after you enter the new key code and it has been accepted. Depending on the product you have purchased, you may need to run the Product Authorization program a number of times. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 5 1 We l c ome Product Authorization T o mo ve t he a uth or i z ati on to a no the r c o mp ute r You can run the software on only the computer that the Product Authorization was run on. If you want to develop your projects on a different computer, you need to complete the following steps to move the authorization from one computer to another. 1. Install Logic Developer - PLC on the computer that the authorization will be moved to. Run the Product Authorization program from the Start menu > Programs > CIMPLICITY Machine Edition > Product Authorization. The Product Authorization dialog box appears. 2. Click Software. There is a Target Site Code on the top right-hand side of the screen. Write down this site code carefully. It must be accurate for the move to work. You will need the Target Site Code when you move the authorized software from the source computer. 3. Click Add. The Product Authorization wizard appears. 4. Click Authorize by disk. At this point, you need to go to the source computer that has the authorized software, and move the authorization to a disk. 5. From the source computer, run the Product Authorization program and click Software. 6. Click Move, and then click OK. Enter the Target Site Code that you wrote down from Step 3 and click Next. Verify that the site code is correct and click OK. 7. Insert a blank formatted floppy disk into the floppy drive and click Next. The authorization code will be moved to the disk and a dialog box should appear telling you it was successful. 8. Click OK. 9. Go back to the computer to which you are moving the authorization and insert the floppy disk. The screen that is asking for an authorization disk should be displayed. 10. Click Next. 11. Click Finish. A screen should appear telling you the move was successful. 12. Click OK. The authorization has now been moved to the new computer. 6 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D We l co me Technical Support TECHNICAL SUPPORT Support is available to registered users at no charge for 90 days after purchase. A support agreement can be purchased from your local GE Fanuc distributor if extended support is required. If problems arise that can’t be solved using the information in your product manual, online Help system, or the GE Fanuc Technical Advisor knowledge base, contact us by telephone, fax, or mail. When contacting us, call from a telephone near your computer and have your CIMPLICITY Machine Edition software running. Have the following information handy to help us assist you as quickly as possible: ■ The serial number from your installation CD case, and the Product name and version number from the Help>About dialog box. ■ The brand and model of any hardware in your system. ■ Operating system and version number. ■ The steps you performed prior to the problem occurring. North America Support Hotline: 1-800-GEFANUC (1-800-433-2682) Fax: (780) 420-2049 Internet: http://www.gefanuc.com Email: support@gefanuc.com Comments about our manuals and help: doc@gefanuc.com Mailing Address: GE Fanuc 2700 Oxford Tower, 10235 - 101 St. Edmonton, AB, Canada, T5J 3G1 South America Telephone: +58 (261) 760 2862 Fax: +58 (261) 765 0909 Internet: http://www.gefanuc.com (visit our Portuguese web site at www.gefanuc.com.br) E-Mail: luis.wilhelm@gefanuc.com Mailing Address: GE Fanuc Automation Latin America Calle 120 con Av. 17, Los Haticos -GE Turbimeca Maracaibo, Venezuela Europe Internet: For up-to-date contact information, visit www.gefanuc-europe.com and click on “Offices and Services”. For up-to-date technical information visit www.gefanuc.com/support. E-mail: plc_europe@gefanuceur.ge.com GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 7 2 CIMPLICITY Machine Edition Machine Edition offers you a complete solution for the development of automation applications in one package. Machine Edition features an integrated development environment and tools that enable you to spend more time building applications and less time learning the software. All Machine Edition products are fully integrated into the environment and interact with each other. ■ They share the same set of tools providing a consistent interface throughout the development process. ■ They feature full drag-and-drop capabilities between tools and editors. ■ They feature a true scalable solution. You have the choice of what type of machine your projects run on. ■ They automatically display Help in the Companion for what you click on. The following illustrates a Machine Edition project: Help Index Toolchest Navigator InfoViewer Inspector Companion Data Watch Feedback Zone CIMPLICITY Logic Developer - PLC Version 4.00 9 2 CIMPLICITY Machin e Edition Quick Start QUICK START Machine Edition makes it easy to get started developing a project. To st ar t Mac hin e Ed itio n 1. Click Start, point to Programs, point to CIMPLICITY Machine Edition and then choose CIMPLICITY Machine Edition. After Machine Edition initializes, the Environment Themes dialog box appears. Note: The Environment Themes dialog box appears automatically the first time you start Machine Edition. To change the theme later, choose Apply Theme from the Windows menu. 2. Choose the Logic Developer - PLC theme. 3. Click OK. When you open a project, the appearance of your Machine Edition screen will match the preview in the Environment Themes dialog box. 10 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D CIMPLICITY Machin e Edition Quick Start The CIMPLICITY Machine Edition dialog box appears. Select this option if you want to create a new project from scratch. Select this option if you want to use a Machine Edition template to create your project. Select this option if you want to select an existing project. Select this option to display only the projects that have been used recently. Select this option to display all existing projects. Select this check box if you do not want to see this dialog box again. 4. Select the appropriate option to open a project. The Open an existing project option is selected by default. Notes: ■ If you select either the Empty project option or the Machine Edition template option, the New Project dialog box appears and you can continue creating a new project (see page 12). ■ If you select the Open an existing project option, you can also select either the Recent Projects option or the All Projects option. The Recent Projects option is selected by default. 5. If you selected the Open an existing project option, select from the list the project that you want to open. The existing projects include samples and tutorials that you can open and use to familiarize yourself with Machine Edition. 6. If you want, select the Don’t show this dialog box on startup option. 7. Click OK. Your project opens in the Machine Edition environment that you specified in the Environment Themes dialog box. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 11 2 CIMPLICITY Machin e Edition Projects PROJECTS You can create and edit Machine Edition projects using products such as CIMPLICITY View, Logic Developer - PC, CIMPLICITY Motion, Logic Developer State, and Logic Developer - PLC. These products share Machine Edition tools to provide a high level of integration between the various parts of your project. You can import folders created with Logicmaster, CimplicityControl, or VersaPro. Using Logic Developer - PLC, you can build multiple projects to suit your specific requirements. T o cr e at e a ne w pr o je ct us ing a t e mp lat e Before creating a project, there are some things you should know: ■ The primary components your project will contain. ■ The PLC you project will run on. 1. From the File menu, choose New Project, or click on the File toolbar. The New Project dialog box appears. Enter the name of your project in the Project Name box. Choose your project template from the Project Template list. You can set the selected project template as the default template by clicking the Set as default button. A sample description of the project appears on the screen. 2. Choose a Project Template that suits your needs. 3. Enter a descriptive Project Name. 4. Click OK. Your project opens in the Machine Edition environment. 12 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D CIMPLICITY Machin e Edition Projects To op en a n ex is ting p r ojec t fo r ed it ing 1. Open the Navigator and choose the Manager tab. A list of projects is displayed. 2. Right-click a project and choose Open. Your project loads and is ready for editing. Want to know more? In the Help Index, look up “Projects”. Navigator: Manager tab T o i mp or t a f ol de r 1. Open the Navigator and choose the Project tab. 2. Select the target that you want to import the folder into. 3. Right-click the target, point to Import, and choose the folder type. 4. In the dialog box that appears, navigate to and double-click the folder you want to import. Want to know more? In the Help Index, look up “import a CimplicityControl folder”, “import a Logicmaster folder”, or “import a VersaPro folder”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 13 2 CIMPLICITY Machin e Edition Tools TOOLS Project development is supported by the Machine Edition tools. Each tool is opened and closed by means of a button on the Tools toolbar. A description of each tool’s function is provided below. Infoviewer Navigator Feedback Zone Inspector Na vig at or 14 Companion Toolchest Data Watch The Navigator is a docking tool window containing a set of tabs. Each tab displays information about your development system in a hierarchical tree structure similar to Windows Explorer. The available tabs depend on which Machine Edition products you have installed and what kind of work you are developing or managing. The Project tab shows the overall organization of your application. Fe e d ba c k Z on e The Feedback Zone window is a docking window used to display several types of output information generated by Machine Edition components. This interactive window uses category tabs to organize the output generated from the Machine Edition products you have installed. I ns pe c to r The Inspector lists the properties and current settings for a selected object or element. You can edit these properties directly in the Inspector. When you select several objects, the Inspector window lists the properties commom to all of them. The Inspector window provides a simple method of viewing and setting properties for all objects. D at a Wa tc h The Data Watch tool is a runtime debugging tool that enables you to monitor and edit the values of variables. This tool is useful while working online to a target. With the Data Watch tool, you can monitor individual variables or user-defined lists of variables. Data Watch lists can be imported, exported, or saved with a project. CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D CIMPLICITY Machin e Edition Tools T o olc he s t The Toolchest is a powerful storehouse of objects you can add to your project. You can drag most items directly from the Toolchest into Machine Edition editors. You can choose from predefined objects or create your own reusable fxClasses. The Toolchest adds true object-oriented capability to Machine Edition. Co mp an io n The Companion provides useful tips and information while you work. While the Companion is open, it tracks your moves and displays help on whatever item is currently selected in the Machine Edition environment. It is context-sensitive and displays a description of whatever you click on the Machine Edition screen. I nf o V i e we r The InfoViewer is an embedded Web browser used mainly to display ■ Machine Edition help. ■ Machine Edition reports. ■ The documentation associated with a project or target. If you are familiar with Internet Explorer or Netscape Navigator, then you are already familiar with the basic InfoViewer interface. Like the Companion, the InfoViewer is context-sensitive. Press F1 to get help on any item you select in the Machine Edition environment. A table of contents is found in the InfoView tab of the Navigator. Want to know more? In the Help Index, look up “Tools: an Overview”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 15 2 CIMPLICITY Machin e Edition Variables VARIABLES A variable (sometimes called a tag) is a named storage space for data values. All variables in a project are displayed in the Variables tab of the Navigator. A variable represents a memory location in the target PLC. Each variable must be mapped to a reference address (for example, %R00001) for all PLC families except PACSystems™ RX7i. On a PACSystems™ RX7i, if you don’t map to a specific reference address, it is considered a symbolic variable. Machine Edition handles all the mapping for you in a special portion of PACSystems™ user space memory. The reference address and other properties of a variable, such as data type, are configured in the Inspector. Navigator: Variables tab 16 Arrays and compound structure variables are supported by Machine Edition. Variable definitions can be imported from and exported to a variety of file types. You can edit your variables in a spreadsheet and then import them. Logic Developer - PLC variables, that is, variables used on GE Fanuc PLC and PACSystems™ targets, can be viewed in CIMPLICITY View. The following diagram shows the Inspector displaying a typical set of variable properties. CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D CIMPLICITY Machin e Edition Variables T o cr e at e a va ri ab le 1. In the Variables tab of the Navigator, right-click choose the data type of the variable. Variable List, point to New Variable and then The New Variable dialog box appears. New Variable menu 2. Type a name for the variable and press ENTER. Variable names can range from 1 to 32 characters, begin with a letter, contain upper or lower case letters, use numbers between zero and nine, and use the underscore character (“_”). 3. Select the target the variable will be used in. 4. If the new variable is an array, select the Array check box and enter the size(s). 5. Click OK. A new variable with a default name appears in the list. T o ma p a v ar iab le t o PL C m e mo ry In order to successfully download a project to the PLC, variables must be properly mapped to the PLC’s memory, unless they are symbolic variables, which a PACSystems™ RX7i will automatically map for you. There are two ways to map a non-symbolic variable. First method: 1. In the Variables tab of the Navigator, right-click a variable and choose Properties. The Inspector displays the properties of the variable. 2. In the Ref Address field, enter an address. You can: GFK-1918D ■ Spell out the exact address, for example, %R00123 or 123R. In either case this maps the variable to %R00123. ■ Enter only the memory area, for example %R. This maps the variable to the next highest available address. For example, if %R00122 was the last address used, entering %R maps the variable to %R00123. CIMPLICITY Logic Developer - PLC Version 4.00 17 2 CIMPLICITY Machin e Edition Variables Second method: 1. In the Variables tab of the Navigator, right-click a variable and choose Properties. The Inspector displays the properties of the variable. 2. Click the Ref Address field and then click the button. The Reference Address Wizard appears. Select an index Select a region of Select a bit reference for a BOOL variable in 16-bit memory. 3. From the Memory Area list, choose a region of PLC memory. 4. In the Index box, enter an index from the beginning of the region. 5. Select a bit reference. The Bit Reference box is available only if you're mapping a BOOL variable to 16bit memory area on a PACSystems™ PLC. 6. Click OK. Your variable is mapped to the Reference Address. Want to know more? In the Help Index, look up “Variables”, “Importing variables from a file”, “Symbolic Variable”, and “Bit addressing in 16-bit memory”. 18 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D CIMPLICITY Machin e Edition Options OPTIONS The Options tab of the Navigator contains option and preference settings. Options are organized into folders and pages. Click or to expand or collapse folders. Examples: Editors > Ladder > View >Coil Justification: The leftmost column in which coils can be placed; also the column where the right power rail resides. The default is 10. PLC> General > Duplicate Addresses: Indicates whether to prevent, warn about, or ignore mapping two variables of the same data size (1, 8, 16, 32, or 64 bits) and length (array size) to the same reference address. Navigator: Options tab PLC > Hardware Configuration >New Reference Assignment: The way in which default reference addresses will be assigned when modules are added to the Hardware Configuration. T o se t o pt ion s and p r e f e re nc e s 1. In the Options tab of the Navigator, expand an options folder to display the option’s properties in the Inspector. 2. In the folder and right-click a page within the Inspector, edit the option’s settings as needed.. Want to know more? In the Help Index, look up “Options”, “Confirmations”, “PLC Options”, and “General Options”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 19 2 CIMPLICITY Machin e Edition Machine Edition Help MACHINE EDITION HELP CIMPLICITY Machine Edition includes a comprehensive online help system that enables you to access specific help topics while working with Machine Edition. Use the InfoViewer or Companion to access help. Companion Help The Companion is a Machine Edition help system that provides useful tips and information while you work. While the Companion is open, it displays help on whatever item is currently selected in the Machine Edition environment, tracking your movements while you work. T o us e Co mp ani on he lp 1. Ensure the Companion window is open. To open it, press Shift+F11. 2. Click on any item on the screen. A description of the item you clicked appears in the Companion. InfoViewer Help The InfoViewer, another Machine Edition help system, provides detailed information. The InfoViewer has its own toolbar for navigating the help system, a Table of Contents (in the InfoView tab of the Navigator), and a searchable index. As with the Companion, InfoViewer help is context-sensitive. Click an item on the screen and press F1 to display the appropriate topic in the InfoViewer. 20 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D CIMPLICITY Machin e Edition Machine Edition Help T o us e the He lp i n de x 1. From the Help menu, choose Index. The Index dialog box appears. 2. Enter a keyword in the top text box or select one in the middle text box. 3. Click List Topics. A list of topics appears in the bottom text box. The topics are sorted by their rating or likelihood of containing the correct information. 4. In the bottom text box, select a topic to display. 5. Click Display. The selected Help topic is displayed in the InfoViewer. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 21 2 CIMPLICITY Machin e Edition Machine Edition Help T o loo k up t op ic s i n t he H e lp T ab le o f C on te nt s 1. Open the InfoView tab of the Navigator. A table of contents for the entire help system appears. 2. Expand Libraries and 3. Double-click a Books to locate a topic of interest topic. The topic is displayed in the InfoViewer. Navigator: InfoView Tab 22 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D 3 GE Fanuc PLC Targets A target represents a run-time destination of the programs you develop with Logic Developer - PLC. Each target contains all of the components that will download to it. Logic Developer - PLC supports the following GE Fanuc PLC target families: Navigator: New PACSystems™ Project ■ PACSystems™ RX7i ■ Series 90™-70 PLC ■ Series 90™-30 PLC ■ VersaMax® PLC ■ VersaMax® Nano/Micro PLC ■ Series 90™ Micro PLC and the following remote I/O interface targets: ■ GE Fanuc Series 90™-70 Genius Remote I/O Scanner ■ GE Fanuc VersaMax® Ethernet ■ GE Fanuc VersaMax® Genius ■ GE Fanuc VersaMax® Profibus CIMPLICITY Logic Developer - PLC Version 4.00 23 G E F a n u c P L C Ta r g e t s 3 Addinging, Configuring and Converting Targets ADDINGING, CONFIGURING AND CONVERTING TARGETS Adding Targets Normally a target is present in a project when you use a template to create the project (see page 12). A project can contain multiple targets. The actual largest number possible may vary, depending on the available memory on your computer, the operating system you are using, or the available disk space, etc. One target is required for each PLC or remote I/O adapter your project accesses, except when you are using CPU redundancy. In this case, one target contains a Primary Hardware Configuration and a Secondary Hardware Configuration, which respectively correspond to the primary PLC and the redundant PLC. For more information, see page 50. Existing targets can be converted from one GE Fanuc PLC family to another. For more information, see page 26. T o ad d a ta rg e t to a pr o je ct 1. In the Project tab of the Navigator, right-click the Project node and point to Add Target. 2. Point to GE Fanuc PLC or GE Fanuc Remote I/O and then respectively choose the PLC family or the Remote I/O. Project right-click menu 24 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Addinging, Configuring and Converting Targets Configuring Targets The properties of a target specify the PLC family, the communication connections between your computer and the PLC, and various other settings. All properties are edited in the Inspector. The following table describes a PLC target’s properties: Name Type Description Documentation Address Family PLC Target Name Update Rate (ms) Sweep Time (ms) PLC Status Dual HWC Selected HWC Physical Port IP Address Additional Configuration Edit the name for your target in this field. The type of target is set by default to GE Fanuc PLC. Note: Logic Developer - PLC is operational with GE Fanuc PLCs only. Enter a description of your project in this field. The maximum characters is 255. Enter the URL where your project documentation is stored. By changing the PLC type in this field, you initiate a target conversion. Caution: Changes are irreversible. The name of the target as stored on the PLC target. Set the rate at which the screen is updated while online. The sweep time of the PLC when online is also displayed on the status bar. The online/offline, run/stop status of the PLC. (Series 90™-70 only.) Indicates whether HWC redundancy is set up. Change the field to False to delete the secondary HWC. (Displayed only if Dual HWC is set to True.) Change the selected HWC in this field. Choose the type of connection to the PLC (Ethernet, COM, or modem). (Ethernet protocol only.) Set the IP address of the PLC. Group of properties used for the detailed configuration of your communication connection. T o co nf i g ur e a PL C tar g e t 1. In the Project tab of the Navigator, right-click a target and choose Properties. The properties of the target appear in the Inspector. 2. In the Inspector, GFK-1918D configure the properties as needed. CIMPLICITY Logic Developer - PLC Version 4.00 25 3 G E F a n u c P L C Ta r g e t s Addinging, Configuring and Converting Targets Converting Targets With Logic Developer - PLC, you can convert targets from one GE Fanuc PLC family type to another. This enables you, for example, to take logic written for a Series 90™-70 PLC and convert it for use on a PACSystems™ RX7i. However, target conversions are irreversible; when logic blocks are deleted during a conversion, they cannot be restored. It is recommended that you make a backup of your project before converting a target in it. There may also be execution differences when converting an application from one GE Fanuc PLC family type to another. You must validate the application execution prior to deployment into a production environment. T o co nve r t a ta rg e t 1. In the Project tab of the Navigator, right-click an existing target and choose Properties. The Inspector displays the target’s properties. 2. In the Inspector, click Family. 3. From the list, choose the new PLC Family you want to convert the target to. Target conversion involves the following changes: ■ Stripping all the configured modules from the original Hardware Configuration (HWC) and setting up the destination family’s default HWC, with a single power supply and a CPU. Note: PACSystems™ RX7i supports many Series 90™-70 modules and some Series 90™-70 expansion racks. When converting a Series 90™-70 target to a PACSystems™ RX7i target, the supported modules and expansion racks are retained (with rare exceptions). The modules’ parameters are also retained or 26 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Addinging, Configuring and Converting Targets converted to the nearest equivalent. Unsupported expansion racks are converted to the nearest equivalent. which retains the supported modules. All Hardware Configuration changes made during the conversion are documented in a target conversion report. ■ Deleting or adding target components, blocks, and/or programs. ■ Updating the system variables, including the fault locating references. ■ Displaying a conversion report in the InfoViewer when converting to PACSystems™ targets only Warning: Changing the PLC Family can result in logic in your project becoming invalid. Note: PLC hardware must be configured before it will be operational. For detailed information on hardware configuration, see page 46.. Want to know more? In the Help Index, look up “Target Conversions (GE Fanuc PLC Targets)”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 27 3 G E F a n u c P L C Ta r g e t s Configuring Communication CONFIGURING COMMUNICATION In order for Logic Developer - PLC to communicate with a target PLC, a connection must be properly configured. The properties of a target are adjustable to accommodate your connection(s). T o co nf i g ur e a n E the r ne t or s e r ial co nn ec t ion 1. In the Project tab of the Navigator, right-click a target and choose Properties. The Inspector opens showing the target’s properties. 2. In the Inspector, set the Physical Port property to Ethernet or a COM port (or a modem if one is installed). 3. If the Physical Port is Ethernet, enter the IP Address of the target PLC. Note: You can connect to a GE Fanuc PACSystems™ RX7i by means of Ethernet only. 4. Double-click Additional Configuration to access the detailed settings for your connection. Note: Serial communication with a non-PACSystems™ PLC is always available if it is the only device connected and an SNP_ID is not specified. An IP address must be set in the PLC before an Ethernet link can be established. Want to know more? In the Help Index, look up “Configuring a direct connection”. Configuring Communication for PACSystems™ The only communication method supported by a PACSystems™ is Ethernet. This ensures fast communication, because every PACSystems™ has an embedded Ethernet adapter. T o co nfig ur e c o mmu nic at ion wit h a P ACS ys t em s ™ RX 7i 1. Physically connect the PACSystems™ RX7i to the Ethernet network. 2. Set up a temporary IP address. For more information, see “To set a temporary IP address for a PACSystems™ RX7i”. The temporary IP address enables you to communicate with the PACSystems™ RX7i the first time. 3. Do one of the following: If there is already a hardware configuration stored on the PACSystems™ RX7i target, it contains a permanent IP address. To obtain this permanent IP address from the PACSystems™, upload the hardware configuration from the PACSystems™ RX7i. - OR - 28 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Configuring Communication Set up a permanent IP address. For more information, see “To set a permanent IP address for a PACSystems™ RX7i”. T o se t a te m po ra r y I P ad dr e ss f or a PA CS ys te m s™ RX 7i 1. In the Utilities tab of the Navigator, double-click Set Temporary IP Address. The Set Temporary IP Address dialog box appears. 2. In the MAC Address field, specify the MAC address for the PACSystems™ RX7i. 3. In the IP Address to Set field, specify the temporary IP address you want to set on the PACSystems™ RX7i. 4. If required, select the Network Interface Selection check box and specify the network interface the PACSystems™ RX7i is located on. 5. Click the Set IP button. The IP address of the specified PLC or device is temporarily set to the indicated address. Warning: The IP address set by the Set Temporary IP Address utility will not be retained through a power cycle. If you want to set a permanent IP address, you must do so by other methods. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 29 3 G E F a n u c P L C Ta r g e t s Configuring Communication T o se t a pe r ma ne nt I P a d dr e ss fo r a PA CS ys te m s™ R X7 i 1. In the Project tab of the The Navigator, right-click the target and choose Properties. Inspector displays the target’s properties. 2. In the IP Address property, enter an IP address. 3. Download the hardware configuration to the PACSystems™ RX7i. For more information, see page 35. Note: Ensure that you have configured the rest of the hardware configuration before downloading it. Want to know more? In the Help Index, look up “Configuring communication with a PACSystems™ RX7i” and “Set Temporary IP Address utility”. Configuring Communication for non-PACSystems™ PLCs T o se t an I P a d dr e ss fo r S e ri es 9 0™ - 70 PL Cs 1. In the Project tab of the 2. Expand the Navigator, expand the Hardware Configuration node. Main Rack and double-click the slot where you want to add a communications module. The Module Catalog appears. 3. Choose the Communications tab and select the communications module you want to add. Select either IC697CMM741 or IC697CMM742. 4. Click OK. The Parameter editor opens showing the configuration settings for the module. 5. In the Settings tab, double-click the IP Address parameter. 30 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Configuring Communication The IP Address dialog box appears.. 6. Enter the IP Address and click OK. T o se t a n I P a d dr e ss fo r a S e rie s 9 0™ - 30 CP U36 4 or CP U37 4 Note: For CPU364 and higher-end Series 90™-30 CPUs, the Ethernet adapter is built into the CPU. For other Series 90™-30 CPUs, the Ethernet connects through an optional expansion slot on the rack. 1. Obtain an IP address, perhaps from your network administrator. 2. In the Project tab of the Navigator, expand the slot containing a CPU364 or CPU374. Hardware Configuration node to reveal the rack and 3. Right-click the slot containing the CPU364 or CPU374 and choose Configure. The Parameter editor appears. 4. In the Parameter editor, click the Ethernet tab. The Parameter editor displays the contents of the Ethernet tab. 5. Double- click the IP address parameter. The IP Address dialog box appears 6. Enter the IP address in the box and click OK. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 31 3 G E F a n u c P L C Ta r g e t s Configuring Communication T o se t a n I P a d dr e ss fo r o the r S e r ie s 90 ™- 3 0 C PUs (n ot CP U36 4 o r CP U37 4) 1. In the Project tab of the Navigator, expand the Hardware Configuration node. 2. Right-click the slot containing an Ethernet Interface Module (IC693CMM321)and choose Configure. The Parameter editor opens showing the configuration settings for the module. 3. In the Settings tab, double-click the IP Address field. The IP Address dialog box appears. 4. Enter the IP address and click OK. T o do wnl oa d an IP a dd re s s to a n on -P AC Sy st e ms ™ ta rg e t 1. Configure a CPU or Ethernet COM Module with an IP address using Hardware Configuration. 2. Right-click the target and choose Properties. The Inspector displays the target’s properties. 3. In the Physical Port property, select a serial connection. 4. Right-click the target and choose Go Online. 5. Right-click the target and choose Download to PLC. The Download to PLC dialog box appears. 6. Select Hardware Configuration and click OK. The IP address is assigned to the PLC. 7. Right-click the target anch choose Go Offline. 8. Right-click the target and choose Properties. 9. In the Physical Port property, select Ethernet. The next time you go online, Machine Edition will use an Ethernet connection with the specified IP address. 32 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Interacting with the PLC INTERACTING WITH THE PLC Communicating with the PLC is necessary to perform such operations as storing and loading programs or monitoring data values and PLC status information. You can connect to a PLC from Logic Developer - PLC over a serial, Ethernet or modem connection, depending on the capabilities of the PLC. All interactions with a target are available from the target’s right-click menu. Validating a Target Validating your project detects any syntax errors that may be present. Error messages are generated for each error and displayed in the Feedback Zone. A project containing errors cannot be downloaded. For that reason, whenever you initiate a download, the logic is automatically validated. T o val ida te a t ar g e t • In the Project tab of the Navigator, right-click a target and choose Validate. Logic Developer - PLC checks all items under the target for syntax errors. Any errors detected are noted with messages in the Build tab of the Feedback Zone. Tip: Double-click an error message to locate the noted error in your project. The appropriate editor or tool opens automatically with the item in question selected. Tips showing you how to proceed are displayed in the Companion. To open the Companion, press SHIFT + F11. Online/Offline When offline from a target PLC, there is no ongoing communication between the PLC and your development computer. When offline from the target PLC the number and type of interactions available are limited, and the actual communication link is not required as long as you only edit logic. If a communication link has been configured and the Offline PLC Operations option is enabled, you can: GFK-1918D ■ Download to the PLC . ■ Upload from the PLC. ■ Start the PLC. ■ Stop the PLC. ■ Clear the PLC. CIMPLICITY Logic Developer - PLC Version 4.00 33 3 G E F a n u c P L C Ta r g e t s Interacting with the PLC When you issue such commands, the communication link becomes active while performing the operation and then returns to an idle state. When the Offline PLC Operations option is disabled, the only PLC operation you can perform while offline is to go online. Note: You enable or disable the PLC Offline Operations option in the Options tab of the Navigator. For more information, see page 19. While online to a target PLC, a communication link exists and is active and you have an ongoing real-time communication with the PLC. You can perform commands to monitor and control the PLC’s action and memory including the commands available when offline. Also, while online, the LD editor displays a graphical representation of LD logic as it executes, if the PLC’s project is equal to the current project. You can edit LD logic while online; you are prompted to download your word-for-word changes. For more information on word-for-word changes, see page 73. Want to know more? In the Help Index, look up “Offline versus Online”. T o go o nli ne to a P LC • In the Project tab of the Navigator, right-click a target PLC and choose Go Online. Logic Developer - PLC connects your project to the PLC. The online status is indicated by the target icon in the Project tab and on the status bar. Note: When online to a PLC, the target icon in the Project tab of the Navigator appears as (equal), (not equal), or (stop faulted). To go o fflin e fr om a PL C • In the Project tab of the Navigator, right-click a target PLC and choose Go Offline. Logic Developer - PLC goes offline. Want to know more? In the Help Index, look up “going online with a PLC” and “going offline from a PLC”. 34 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Interacting with the PLC Upload/Download The download process creates (or builds) and validates all runtime files necessary for a target to perform its role in a completed project. The compiled project is then transferred to the target hardware via the communication connection previously configured. For more information, see page 28. The upload process acquires a project from an active PLC target and transfers it to Logic Developer - PLC for editing. T o do wnl oa d to a ta r ge t PL C 1. In the Project tab of the choose Download to PLC. Navigator, right-click the target to which you want to download files and The Download to PLC dialog box appears. Note: If the PLC is running, you can download only logic that is not equal to the PLC’s current logic and the Download to PLC dialog box does not appear. 2. Choose the items you want to download and click OK. Tip: To download files for all targets in a project, right-click the project node and choose Download All. If you want to download files to the active target, choose Download Active Target. Note: Only one project can be downloaded to a target at a time. If you download to a target machine that already has a project on it, the existing project is overwritten. For each target that you download to, Machine Edition saves the project, performs a validation, builds the runtime files and attempts to establish a connection to the target. Any errors that occur are displayed in the Build tab of the Feedback GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 35 3 G E F a n u c P L C Ta r g e t s Interacting with the PLC Zone. If connection to a target is successful, Machine Edition sends all the necessary runtime files to the PLC. Want to know more? In the Help Index, look up “downloading to PLC”. To upl oa d files fr om a PL C 1. In the Project tab of the Navigator, right-click the information and choose Upload from PLC. target PLC from which you want to upload The Upload from PLC dialog box appears. Note: If you are uploading from Logic Developer - State, only the Hardware Configuration can be uploaded. 2. Choose the item(s) you want to upload and click OK. Logic Developer - PLC connects to the PLC and uploads the selected item(s) to Logic Developer - PLC. If you already had a version of the PLC’s project open, the uploaded project merges with the existing project. This ensures that all variable names are retained throughout the uploading process. If you upload to an empty target, all variables are assigned default names. For example, %R00001 is named R00001. Want to know more? In the Help Index, look up “uploading from PLC”. Run/Stop You can set a target PLC to Run or Stop mode. In Stop mode, you can choose to enable or disable the outputs. If you are starting a PACSystems™ RX7i or Series 90™-70 PLC, you can choose to have outputs enabled or disabled. 36 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Interacting with the PLC T o st ar t a PLC • In the Project tab of the Navigator, right-click a Commands, and then choose Start PLC. target, point to Online Commands or to Offline The target PLC begins executing its program. T o st op a P LC 1. In the Project tab of the Navigator, right-click a Commands, and choose Stop PLC. target, point to Online Commands or to Offline The Stop PLC dialog box appears, prompting you to enable or disable the PLC’s outputs. 2. Select an option. 3. Click OK. The target PLC stops executing its program. Want to know more? In the Help Index, look up “starting the PLC” and “stopping the PLC”. Fault Tables The PLC and I/O Fault Tables display fault information logged by the CPU or modules in the PLC. This information is used to determine if there are problems with the PLC hardware or software running in the PLC’s CPU. To view the PLC and I/O fault tables, your computer must be online to the PLC. T o vie w t he f ault t ab le r e po r ts • In the Project tab of the Diagnostics. GFK-1918D Navigator, right-click the target you want to report on and choose CIMPLICITY Logic Developer - PLC Version 4.00 37 3 G E F a n u c P L C Ta r g e t s Interacting with the PLC The fault table appears in the InfoViewer window. Choose the type of fault information you require. Indicates online status of PLC. Print fault table by clicking here. Select the format of fault data. View the date and time of the faults. Sort fault information. Double-click a row to view details of faults. Clear fault information by clicking here. Want to know more? In the Help Index, look up “fault”, then select “Working with the Fault Tables”. Reference View Tables The Reference View Tables (RVTs) are tables of reference addresses that can be monitored and changed in real-time. In the Project tab of the Navigator the Reference View Tables folder contains a Default Tables folder and you can add user-defined tables to the Reference View Tables folder. A target can have zero or more user-defined RVTs. The number of entries contained in an RVT does not affect performance. Performance is affected only by the number of entries that are displayed and have to be updated in the view. An RVT displays data when the parent GE Fanuc PLC target is active and online. You can configure the appearance of your RVTs in the Options tab of the Navigator. 38 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Interacting with the PLC Data values at sequential addresses are displayed, by default, from right to left, starting at the reference address specified. Both default and user-defined RVTs display rows of 8 cells for discrete memory and rows of 10 cells for register memory. The amount of data displayed in the columns depends on the data display format. Selected address Starting Address Format of selected address Subsequent addresses are displayed right to left by default. This is the data at the starting address. Display format can be selected for individual cells or the entire table. T o cr e at e a us e r- d e f i ne d R e f e re n ce V i ew T a ble • In the A new GFK-1918D Project tab of the Navigator, right-click on the Reference View Tables folder and choose New. Reference View Table with a default name is added to the folder. CIMPLICITY Logic Developer - PLC Version 4.00 39 3 G E F a n u c P L C Ta r g e t s Interacting with the PLC T o wo rk w ith a Re f e r e nc e V i e w T ab le 1. n the Project tab of the table you want to view. Navigator, expand the Reference View Tables folder and double-click the The Reference View Table appears in the Machine Edition main window. 2. Add reference addresses to the table as required. Note: You cannot add reference addresses to a default RVT. 3. Format the table entries as desired. Want to know more? In the Help Index, look up “RVT”, then select “Working with Reference View Tables. Navigator: Project Tab Reference View Table node Reports Reports provide summaries and tables of information about your project. Most reports are displayed in the InfoViewer window (see page 20). The Reports tab of the Feedback Zone contains a list of all reports generated since the last Machine Edition project was opened. The following list shows the types of reports and logic printouts available in Logic Developer - PLC: Address Use report C block report* Hardware Configuration report IL block report* Variables report(s) Local Logic block report * CAM profile report Motion block report* Online Force Report Notes ■ An asterisk (*) indicates a logic printout. ■ Reports are not generated for LD blocks. Rather, these blocks are printed directly from the Program Blocks node. T o ge n er a te r e po r ts • In the node. Project tab of the Navigator, right-click a node and choose Report to generate a report on that A report is automatically generated and displayed in the InfoViewer. 40 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D G E F a n u c P L C Ta r g e t s Interacting with the PLC Note: To generate an Online Force report for a target, you must be online to the target. Right-click the target, point to Online Commands, and then choose Online Force Report. T o re d is pla y a p re v iou sly g e ne ra te d r e po r t 1. In the Feedback Zone, double-click the Reports tab. A list of previously generated reports appears in the Feedback Zone. 2. From the list choose the report you want to view. The report displays in the Infoviewer. Many items in a report contain hyperlinks. Click a hyperlinked item to jump to that item in the project. For example, if a variable's name appears hyperlinked in a report, clicking it selects that variable in the Variables tab of the Navigator. Large reports are often separated into several pages. To view a different page of the report, scroll to the bottom of the report in the InfoViewer and click the number of the page you want to view. T o pr i nt a re p o rt d isp la ye d i n t he I nf o V i e we r 1. Do one of the following: ■ Generate the report you want to print. - OR ■ Redisplay a previously generated report. 2. When the report is displayed, right-click the InfoViewer window and select Print. Want to know more? In the Help Index, look up “Reports”. To pr int L D Blo ck s 1. In the Project tab of the Navigator, expand the Logic node. 2. Right-click the Program Blocks node and choose Print LD Blocks. The Print dialog box appears. 3. Select the blocks to print. ■ To print all of the target's LD blocks, select the All option. ■ To print only some of the target's LD blocks, select the Selection option, then select the check box in front of each block you want to print. 4. Select options as required and click OK. Want to know more? In the Help Index, look up “printing LD logic”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 41 4 Hardware Configuration (HWC) Logic Developer - PLC supports six GE Fanuc PLC families and various remote I/O interfaces (see page 59) with a variety of CPUs, racks and modules for each. In order to operate, PLC hardware must be configured with Logic Developer - PLC or some other GE Fanuc tool. The HWC component of Logic Developer - PLC provides a way to completely configure your target equipment. This chapter details specifics on configuring PLC hardware for your operational needs. The first step in configuring PLC hardware is to select the PLC you want to configure (see page 24). When creating a new project, you can use a project template containing default hardware configuration, or you can create an empty project and configure it manually. PACSystems™ RX7i The PACSystems™ RX7i, pictured below, is the newest family of GE Fanuc PLCs. Most of its features are based on the features of the Series 90™-70 PLC family. The PACSystems™ RX7i’s Ethernet capabilities are based on the Series 90™-30 CPU364. Power Supply Rack CPU I/O Modules The PACSystems™ RX7i consists of a main rack and up to seven expansion racks. The PACSystems™ RX7i supports two types of main racks, IC698CHS017 and IC698CHS117. It supports five types of expansion racks, all of them Series 90™-70 racks. All main racks and expansion racks support three non-intelligent Series 90™-70 fan kits. CIMPLICITY Logic Developer - PLC Version 4.00 43 Ha rd war e Con fig ur atio n (H WC) 4 The PACSystems™ RX7i main racks have 18 single-width VME slots. Slot 0 supports two power supply modules: IC698PSA100 and IC698PSA350. Slots 1 and 2 are used to house a double-width CPU. PACSystems™ RX7i supports two CPUs IC698CPE010 (300 mHz) and IC698CPE020 (700 mHz). The PACSystems™ RX7i communicates through Ethernet only and the CPU has an embedded Ethernet adapter. In addition to the Ethernet adapter, up to three IC698ETM001 Ethernet modules can be installed in a PACSystems™ RX7i main rack. The Ethernet modules occupy only one slot. All of the IC698 modules are supported only on the main racks. PACSystems™ RX7i supports several Series 90™-70 modules. Each one is doublewidth, that is, it occupies two slots on the main rack, but it occupies only one slot on a Series 90™-70 expansion rack. You can plug double-width modules into any two adjacent slots of the main rack except slots 0, 1, or 2. Because slot 17 is a double-width slot, any module in slot 17 occupies only slot 17. Slot 17 can also accept a single-width module. PACSystems™ RX7i supports the following Series 90™-70 bus expansion modules: ■ IC697BEM711 ■ IC697BEM713 In addition to the Series 90™-70 support, PACSystems™ also supports numerous Genius devices. Configuring PACSystems™ RX7i Hardware When you create a target with a PACSystems™ RX7i rack system, the default HWC consists of the main rack, with a power supply in slot 0 and a single CPU in slots 1 and 2. You can change the default power supply and CPU, and add single-width or double-width modules. You can add up to seven secondary racks, and on each of these, you can add Series 90™-70 modules. Note: On PACSystems™ RX7i targets, only one rack is added by default. On Series 90™-70 and Series 90™-30 PLCs, seven secondary racks are added by default to the HWC. You do not need to add them. The configuration of the PACSystems™ RX7i is detailed in the following procedures. Configuration procedures for the other PLC types supported by Logic Developer - PLC are almost identical. Navigator: Project Tab displaying the HWC node of a PACSystems™ RX7i 44 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) T o ch oo s e a po we r s up ply The default power supply for the PACSystems™ RX7i is the PSA100. To change the power supply: 1. In the Project tab of the Navigator, right-click Slot 0 and choose Replace Module. A list of available power supplies appears. Note: For other GE Fanuc PLC families, there is no Slot 0. Right-click the PWR node instead. 2. Select the power supply you have installed in your rack and click OK. T o ch oo s e a CPU The default CPU specified in all project templates for a PACSystems™ RX7i is the CPE010. To change the CPU: 1. In the Project tab of the Navigator, expand the Hardware Configuration folder. All racks are revealed. 2. Expand the 3. Right-click Main rack. Slot 1 and choose Replace Module. HWC right-click menu GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 45 4 Ha rd war e Con fig ur atio n (H WC) The Module Catalog dialog box appears. 4. From the list, select a CPU. 5. Click OK. A dialog box appears asking if you want to retain the settings from the existing CPU. 6. Click Yes or No. Note: On targets other than PACSystems™, you are prompted to confirm the replacement. The target is configured with the selected CPU. T o co nf i g ur e a CP U 1. In the Project tab of the Navigator, right-click a slot containing a CPU and choose Configure. The Parameter editor appears showing all configurable settings for the CPU. 46 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) 2. Modify the settings as required. For information on any parameter, select the parameter. Help is displayed in the Companion. Tip: To open the Companion, press SHIFT+F11. T o ad d a se c on da ry r ac k (PA CS ys te m s™ RX 7i onl y) Note: On Series 90™-70 and Series 90™-30 PLCs, seven secondary racks are added by default to the HWC. You do not need to add them. 1. In the Project tab of the Navigator, right-click the HWC node and choose Add Rack. The Module Catalog dialog box appears listing available rack types. 2. Select a rack and click OK. Navigator: Project tab PACSystems™ HWC configuration The Series 90™-70 expansion rack is added to the PACSystems™ RX7i rack system. It is assigned an available number in the range of 1 through 7, excluding numbers already assigned to other expansion racks. T o re p la ce a r ac k 1. In the Project tab of the Navigator, right-click a rack node and choose Replace Rack. The Module Catalog dialog box appears listing available rack types. 2. Select a rack and click OK. Navigator: Project tab HWC configuration GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 47 4 Ha rd war e Con fig ur atio n (H WC) T o ad d a fan k it t o a ra c k (PA CS ys te m s™ R X7 i o nly ) 1. In the Project tab of the 2. Right-click a Navigator, expand the Hardware Configuration folder. rack and choose Properties. The rack’s properties are displayed in the Inspector. 3. In the Inspector, to the right of the Fan Catalog Number property, click . The Fan Kits catalog opens. 4. Select the fan kit you want to add and click OK. The fan kit is added to the rack. T o co nf i g ur e t he Et he r ne t da ug hte r bo a rd (P AC Sy st e ms ™ R X7i on ly) 1. In the Project tab of the Navigator, expand the Main rack), and then Slot 1. 2. Double-click Hardware Configuration folder, then Rack 0 (the Ethernet adapter. The Parameter Editor window opens. 3. Configure the Ethernet adapter’s parameters as needed. Navigator: Project tab PACSystems™ Ethernet Daughterboard 48 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) T o ad d an Eth e rn et m od ule ( PA CS ys te ms ™ R X7 i o nly) 1. In the Project tab of the (the Main rack). Navigator, expand the Hardware Configuration folder and then Rack 0 2. Right-click the slot you want to add an Ethernet module to and choose Add Module. The Module Catalog opens. 3. In the Communications tab of the Module Catalog, select the Ethernet Module and click OK. The Ethernet module is added to the slot. 4. Double-click the Ethernet module (IC698ETM001). The Parameter Editor opens. 5. Configure the Ethernet module’s parameters as needed. Want to know more? In the Help Index, look up “configuring a PACSystems™ RX7i Rack System”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 49 4 Ha rd war e Con fig ur atio n (H WC) Redundancy (Series 90™-70 and PACSystems™ RX7i only) In redundant systems, two units are set up and configured to share the responsibility of a single unit. If one unit fails or is taken offline, the other unit assumes responsibility without interrupting operation of the entire system. There are three types of redundant systems: ■ Basic CPU Redundancy (Series 90™-70 only) ■ Genius Redundancy ■ CPU Redundancy Over Genius (Series 90™-70 only) Bas ic CP U R e d und anc y (Series 90™-70 CPUs CGR772 and CGR935 only.) To implement CPU redundancy, a single target is associated with two physical PLCs, a Primary and a Secondary. Both PLCs share the same logic, but each has its own Hardware Configuration (HWC): Primary or Secondary. The selected HWC is the HWC that you can go online with, download to, upload from, and so on. Series 90™-70 rack systems support three types of basic CPU redundancy. These redundant systems can be used in combination with Genius redundancy schemes. Navigation: Project Tab HWC Node CPU Redundancy (Series 90™-70 only) 50 ■ Single Bus with Preferred Master - uses a single Genius bus with one or more bus controllers in each PLC. The primary unit is always chosen as the active unit when the units initially synchronize. ■ Single Bus with Floating Master - uses a single Genius bus with one or more bus controllers in each PLC. No switchover occurs on initial synchronization to make the primary unit the active unit. ■ Dual Bus with Floating Master - uses dual busses with one or more bus controllers in each PLC. No switchover occurs on initial synchronization. Bus Switching Modules (BSMs) are required in accordance with configuration of a dual bus network. This option provides redundancy of both the PLC and the I/O bus. CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) G e nius R e du nd anc y (PACSystems™ RX7i and Series 90™-70.) A redundant Genius system contains duplicate components that are controlled in a way that keeps the Genius system operating properly even if one of the duplicate components fails or is taken out of service. Redundant Genius systems can be used in combination with Series 90™70 redundant CPU systems. You can configure five types of redundant Genius systems: ■ Genius Dual Bus Redundancy (Paired GBC Internal) ■ Genius Dual Bus Redundancy (Paired GBC External) ■ Genius Dual GBC Redundancy (Paired GBC Internal) ■ Genius Dual GBC Redundancy (Paired GBC External) ■ Genius Dual Bus & Dual GBC Redundancy CPU R e dun da nc y O ve r G e nius (Series 90™-70 only.) A CPU Redundancy Over Genius system contains duplicate components that are controlled in a way that keeps the system operating properly if one of the duplicate components fails or is taken out of service. Five types of CPU Redundancy Over Genius systems can be built upon the various types of redundant Genius systems combined with the basic CPU Redundancy schemes. ■ CPU Redundancy (GHS) Using Genius Dual GBC Redundancy (Paired GBC External) - Single Bus with Preferred Master ■ CPU Redundancy (GDB) using Genius Dual GBC Redundancy (Paired GBC External) - Single Bus with Floating Master ■ CPU Redundancy (GDB) using Genius Dual Bus Redundancy (Paired GBC External) - Single Bus with Floating Master ■ CPU Redundancy (GDB) using Genius Dual Bus and Dual GBC Redundancy Dual Bus with Floating Master ■ CPU Redundancy (GDB) using a Mixed Genius Redundancy Scheme Want to know more? In the Help Index, look up “Redundant HWC Overview”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 51 4 Ha rd war e Con fig ur atio n (H WC) Configuring Redundant Systems The procedures below are the general steps to follow for configuring redundant systems. For the procedures on configuring specific redundancy sytems, see the online help. To se t up t he p rim ar y h ar d war e c o nfig ur at ion fo r CPU re d und a ncy (S eri e s 9 0™ - 70 o nly) 1. In the Project tab of the redundancy. 2. Right-click Navigator, expand the target node for which you want to set up CPU Hardware Configuration, point to Redundancy, and choose Wizard. The Redundancy Wizards dialog box opens, with the Set up a Primary Hardware Configuration for CPU Redundancy option selected by default. 52 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) 3. Click Next and follow the wizard to the end. The wizard adds a redundant CPU, the Bus Transmitter Module (BTM) and the Redundancy Communications Module (RCM) to the configuration. Note: The target property, Dual HWC, is now available in the Inspector and is set to False. Ad d ing G e nius B us Co ntr o lle rs ( GB C) t o you r sy st e m (P AC Sy st e ms ™ R X7i an d Se r ie s 90 ™ -7 0) 1. In the 2. Right-click Project tab of the Navigator, expand the target for which you want to set up redundancy. Hardware Configuration, point to Redundancy, and choose Wizard. The Redundancy Wizards dialog box appears. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 53 4 Ha rd war e Con fig ur atio n (H WC) 3. Select Add GBCs for Genius Redundancy. 4. Click Next and follow the wizard to the end. The wizard allows you to select a Genius redundancy scheme and the location of the GBC modules. You can run this wizard multiple times to configure additional pairs of redundant busses in the same system. Note: When you add a Genius Bus Controller (GBC) to a Series 90™-70 rack, a new Genius bus network is automatically created and associated with that slot and GBC module. Up to 31 Genius I/O devices (blocks) can be connected to a GBC through its Genius bus. Co nfig ur ing th e s e co nd ar y h ar dw ar e c on fig ur at ion (S eri es 9 0™ - 70 o nly) 1. In the Project tab of the Navigator, select the Hardware Configuration folder. 2. Right-click Hardware Configuration, point to Redundancy, and choose Mirror to Secondary Hardware Configuration. A secondary rack system that is a copy of the primary rack system is generated. The target now displays two Hardware Configurations (HWCs), one labeled [Primary] and the other, [Secondary]. The Primary HWC is bolded because it is currently selected. The target property, Dual HWC, is now set to True. 54 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) Note: You can mirror as many times as necessary to synchronize the two HWCs after modifying the primary HWC. Each time you mirror the primary HWC, the secondary HWC is updated to reflect those changes. Want to know more? In the Help Index, look up “Redundancy”. Series 90™-30: DSM314 Motion Module The Series 90™-30 supports a module which no other GE Fanuc PLC family supports: the Motion Mate DSM314 (see page 91). The DSM314 is a high performance, easy-to-use multi-axis motion control module. Compatible with Series 90™-30 PLC logic solving and communications functions, the DSM314 supports the following servo types: ■ Digital - GE Fanuc digital servo amplifiers and motors. ■ Analog - GE Fanuc SL Series analog servos and third-party servos. The DSM314 Motion module has four axes that can be individually configured in Standard or Follower mode. It can control up to four analog mode servo axes or up to two digital mode servo axes. When axis one and two are controlling digital mode servos, axis three can control an analog servo. In order to perform motion programming in Logic Developer - PLC, you must have a DSM314 motion module properly configured (see page 91). T o ad d a DS M3 14 mo t ion mo d ule 1. With a rack of the Hardware Configuration node expanded, right-click the empty slot you want to add a DSM314 motion module to and choose Add Module. The Module Catalog dialog box appears. 2. On the Module Catalog dialog box, click the Motion tab. A selection of motion modules appears in the Module Catalog dialog box. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 55 4 Ha rd war e Con fig ur atio n (H WC) 3. From the list, select Motion Mate DSM314. 4. Click OK. A DSM314 is added to the hardware configuration of your project. T o co nf i g ur e a D S M31 4 1. In the Project tab of the Navigator, double-click the slot containing a Motion Mate DSM314. The Parameter editor appears. 2. Configure the DSM314 by using the Parameter editor. Note: For details on configuring the DSM314, see GFK-1742, Motion Mate DSM314 for Series 90-30 PLCs Users Manual . 56 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) Series 90™-70 Genius Remote I/O Scanner A Remote I/O Scanner (IC697BEM733) is a Genius device that is part of a Genius Bus system. As such, it is added as a Genius device to the Genius Bus Controller (GBC) and it is represented in Logic Developer - PLC by an SBA node under the GBC node in a Series 90™-70 target. Navigator: Series 90™-70 Remote I/O Scanner as a Genius device under a GBC A Remote I/O Scanner resides in Slot 1 of the main rack of a Series 90™-70 PLC. I/O modules can be inserted into the other slots of the main rack and on all the slots of the other racks. As such, the Remote I/O Scanner is represented by a target in the Project tab of the Navigator, and is also represented by a module in slot 1 of the main rack of that target. Navigator: Series 90™-70 Remote I/O Scanner as a target and as a module in Slot 1 of the main rack GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 57 4 Ha rd war e Con fig ur atio n (H WC) T o se t up a R e mo te I /O S c an ne r 1. Add the Remote I/O Scanner as a Genius device to the GBC. 2. When prompted to add a new target for the Remote I/O Scanner, click Yes. Logic Developer - PLC automatically sets up some of the properties that link the Remote I/O Scanner to its GBC. 3. Set up the SBA to the same value to the Remote I/O Scanner as a target and to the Remote I/O Scanner as a Genius Device. Now whenever you update the I/O map on the Remote I/O Scanner, the I/O map is automatically updated to the GBC. 4. Configure the Remote I/O Scanner’s target properties. 5. Add and configure the I/O on the Remote I/O Scanner’s rack system. 6. Configure the Remote I/O Scanner’s module properties. 7. Configure the properties of the Remote I/O Scanner as a Genius bus device. Want to know more? In the Help Index, look up “IC697BEM733, Remote I/O Scanner”. 58 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) VersaMax Remote I/O VersaMax remote I/O consists of a Network Interface Unit (NIU) (Ethernet, Genius or Profibus), and one or more I/O modules. If your target type is remote I/O, you can use Logic Developer - PLC to configure this hardware. Once configured, the remote I/O can be controlled from a PLC or PC controller. The differentiating factor between a VersaMax remote I/O and a PLC is that a remote I/O is simply an input/output device with a communication interface. Unlike a PLC, a remote I/O has no CPU. When working with the VersaMax Remote I/O hardware configuration, Logic Developer - PLC enables you to add racks, configure the power supply and configure modules. Remote I/O targets are generally added to a project when you create a project with a template (see page 12). You can add additional Remote I/O targets later. Navigator: VersaMax Remote I/O T o cr e at e a p ro je c t c o nta inin g a G E Fa nuc R e mo te I/ O t ar g e t f ro m a t e mp lat e 1. From the File menu, choose New Project. The New Project dialog box appears. 2. From the Project Template list, choose the GE Fanuc Remote I/O you want to add to your project. 3. Enter a descriptive Project Name. 4. Click OK. A new Remote I/O project is started. T o ad d a GE Fa nuc R e mo te I/ O ta rg e t to an e xi st ing p ro je c t 1. In the Project tab of the Navigator, right-click the Project node. 2. Point to Add Target, then to GE Fanuc Remote I/O, and choose the remote I/O you want to add. Note: The Series 90-70 Genius option is a Series 90™-70 Remote I/O Scanner (see page 57). GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 59 4 Ha rd war e Con fig ur atio n (H WC) T o re p la ce t he p o we r su pp ly fo r yo ur r e mo te I /O c o nfig ur at ion 1. In the Project tab of the Navigator, expand the Hardware Configuration node of the remote I/O. The Navigator displays the following: 2. Right-click the PWR node and choose Replace Module. The Module Catalogue dialog box appears: 3. From the list, select the power supply that you want to configure for your system. T o ad d a ne w C ar rie r /Ba s e to y our V e r s aMa x Re m ot e I /O 1. In the Project tab of the Navigator, select a remote I/O target. 2. Expand the Hardware Configuration node and the Main Rack node. The Navigator displays the following: 3. Right-click the 60 Slot 0 node and choose Add Carrier/Base. CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Hardware Configuration (HWC) The Module Catalog dialog box appears. 4. Select the carrier/base that you want to add to the remote I/O target. Note: You can add a maximum of eight carrier modules to each VersaMax® rack. 5. Click OK. T o ad d a mo dul e to a c ar r ie r/ ba se 1. Double-click an empty carrier/base. The Module Catalog appears. 2. From the Module Catalog list, select the module that you want to install. Want to know more? In the Help Index, look up “Hardware Configuration”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 61 5 Logic Editors The following logic types are supported by Logic Developer - PLC (not including motion programming) and are compiled and downloaded to the PLC represented by the associated GE Fanuc PLC target. The Logic folder of a GE Fanuc PLC target includes: ■ Ladder Diagram (LD) Blocks ■ Instruction List (IL) Blocks ■ C Blocks ■ C programs These items will be downloaded to, and run on, the target. Each block and user program is a named section of executable code. Blocks can be grouped under user-defined folders in the Program Blocks folder. C programs are grouped under the main Logic folder. Each target must contain one block or user program named “_MAIN”. On any target except a release 6 or later Series 90™-70 PLC, the _MAIN block is first to execute when the project is downloaded to a PLC. Depending on the type of target PLC, blocks other than”_ MAIN” can be scheduled for execution based on timer or I/O interrupts. Note: On release 6 or later of Series 90™-70 PLCs, the LD program can be scheduled. That is, the Series 90™-70 PLC does not necessarily execute the _MAIN LD block first. Want to know more? In the Help Index, look up “LD Program”. CIMPLICITY Logic Developer - PLC Version 4.00 63 Logic Editors 5 T o cr e at e a us e r- d e f i ne d f o lde r 1. In the expand the Project tab of the Logic folder. Navigator, expand the target with the logic you want to organize and then 2. Right-click the Program Blocks folder, point to New, and choose Folder. A new user-defined folder appears with a default name. 3. Optionally enter a new folder name, which must be unique among the folders directly under the Program Blocks folder. Want to know more? In the Help Index, look up "PLC" then choose “Organizing Your PLC Logic”. T o sc he d ule e x e cu ti o n o f a lo g ic bl oc k 1. In the Project tab of the Navigator, right-click an existing LD, C or IL block, and choose Properties. The block’s properties appear in the 2. In the Inspector, click the Inspector. button in the Scheduling property. The Scheduling dialog box appears. 3. Configure scheduling by entering values in each of the fields. Inspector: IL, LD, C properties 64 Want to know more? In the Help Index, look up “Scheduling.” CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors T o se t a cc e ss c o ntr o l 1. Right-click an LD, IL or C Block and choose Properties. 2. In the Inspector, expand the Lock Settings property. 3. In the Lock Type property, choose a setting from the list. 4. In the Password property, enter a password. T o se a rc h/ re p la ce i n o ne b lo ck 1. Double-click an LD or IL block to open it. 2. From the Search menu, choose Find or Replace. A dialog box appears. 3. In the Find what or in the Text to find field, enter the text to find. 4. (Only if you want to replace text) In the Replace with field or in the New text field, enter the text to replace the found text with. 5. Select or clear each search/replace option, as required. 6. Click Find, Find next, Replace, Replace All, Close, or Cancel, as required. Note: Logic Developer - PLC provides the capability to search for some text in an entire target or portions thereof, which you can specify. Various options are available to narrow a search. Want to know more? In the Help Index, look up “Global” and select the “Conducting a Global Search” help topic. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 65 5 Logic Editors LD Editor LD EDITOR The Ladder Diagram (LD) editor is used to create programs with the Ladder Diagram programming language. LD logic graphically represents the programmed actions performed by a PLC as it executes. The LD editor is cell-based with rungs constructed of horizontal sequences of instructions that are wired together. A given instruction and its operands can occupy one or more cells. Navigator: Project tab An LD Block You can work with the LD editor while offline to edit a disk copy of a project, or while online to monitor the execution of the logic while you fine tune the project by making word-for-word changes (see page 73). You can customize the appearance and behavior of the LD editor. An LD block is a named section of LD Logic that is compiled and downloaded to the PLC represented by the associated target. The following table describes the number of blocks supported by each CPU type for a given target. CPU Type Number of Blocks Maximum Number of Blocks VersaMax 64 subroutine blocks plus one _MAIN block 65 Series 90™-30 64 subroutine blocks plus one _MAIN block 65 Series 90™-70 255 subroutine blocks plus one _MAIN block 256 PACSystems™ 511 subroutine blocks plus one _MAIN block 512 T o cu st om i ze the L D e d i to r 1. In the Options tab of the 2. Right-click a Navigator, expand the Editors folder and then the Ladder folder. page (Confirmations, Editing, Font and Colors, or View), and choose Properties. The configurable settings appear as properties in the Inspector. 3. In the Inspector, adjust settings as required. T o cr e at e a n L D bl oc k 1. In the Project tab of the choose LD Block. 66 CIMPLICITY Logic Developer - PLC Version 4.00 Navigator, right-click the Program Blocks folder point to New, and then GFK-1918D Logic Editors LD Editor A new LD block with a default name is created. Note: If you use a template or add a target, the first block added to a target is named “_MAIN” and subsequent blocks added are named LDBK1, LDBK2, and so on, by default. 2. Rename the block as desired. T o op e n a n LD b lo ck f o r e d i ti ng • In the Project tab of the Navigator, double-click an LD block. The block opens in the LD editor. Note: You can have multiple blocks open for editing. To navigate to another open LD block, click the tab that displays its name at the bottom of the editor window. Working with the LD Editor Offline While in offline mode, there is no live communication between the LD editor and the target. Most logic development is done while offline. The following diagram illustrates some of the more common operations you can perform using the ladder editor offline. Insert common instructions and wiring with the ladder instruction toolbar. In-place editor comment rungs. Drag variables to instruction operands to assign them. Right-click to insert an instruction. Use the Inspector to configure address and length for instructions The Companion tracks your moves and provides information on what you click. GFK-1918D Drag LD instructions from the Toolchest. Displays a list of the places the selected variable is used in the References tab of the Feedback Zone. CIMPLICITY Logic Developer - PLC Version 4.00 67 5 Logic Editors LD Editor To ins e rt a n in st ruc t ion 1. In the LD editor, right-click an empty cell and choose Place Instruction. A smart list appears listing all available instruction mnemonics. 2. Choose an instruction mnemonic from the list and press ENTER. Note: Only functions that have no inputs can be placed in the first column. T o co nf i g ur e a n i nst r uct i o n’s a dd re s s a nd le ng th pr o pe r tie s There are two methods to configure an instruction’s address and length properties. First method 1. In the LD editor, insert an instruction that requires Address and/or Length configuration. Four question marks correspond to the Address property Two question marks correspond to the Length property. 2. Right-click the instruction and choose Properties. The Inspector displays the instruction’s properties. Address Field Length Field 3. In the Address property, enter a variable name or a reference address to specify the start of a memory block. Note: If you type a reference address, it is converted to a variable name automatically. 4. In the Length property, enter the number of PLC registers that the instruction requires in the memory block. 68 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors LD Editor Second method 1. In the LD editor, insert an instruction that requires Address and Length configuration. Four question marks correspond to the Address property Two question marks correspond to the Length property. 2. Double-click the instruction or select it and press ENTER. The Function Properties dialog box appears. 3. In the Address property, enter a variable name or a reference address to specify the start of a memory block. Note: If you type a reference address, it is converted to a variable name automatically. 4. In the Length property, enter the number of PLC registers that the instruction requires in the memory block. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 69 5 Logic Editors LD Editor T o as s ign va ria b le s to i ns t ruc ti on op e r and s 1. In the LD editor, double-click beside any operand of an instruction, or click there and press ENTER. A smart list appears prompting you to enter a variable name or reference address. Note: If the smart list that appears prompts you for a mnemonic, supply a contact or a wire. 2. Type, or choose from the list, a variable name or reference address. If you enter a reference address, a variable name will be automatically substituted. Editing Logic as Text You can enter LD logic into the LD editor by starting to type right into a cell. The smart list will appear and you can contirue type your instructions and operands. When you press ENTER, the logic you typed will appear in customary graphic form in the LD editor. For example, in the first cell of a new rung, if you type AD MyDint1 MyDint2 Result12;AD MyDint3 MyDint4 Result34, the following logic will appear in the LD editor: A horizontal wire was inserted in the first cell to make room for the ADD_DINT insturction’s operands and the operands were inserted in their proper places. In the keyboard entry, "AD" stood for "ADD_DINT", because it was the first available instruction that begins with "AD" in the smart list. A semicolon separates the ADD_DINT instructions. The required horizontal wires are supplied automatically.. Want to know more? In the Help Index, look up “Keyboard Method”. A powerful extension of typing logic into the LD editor is the ability to write LD logic in any text editor and copy and paste it into the LD editor, or to copy and paste logic from the LD editor to a text editor. You can copy an entire block of LD logic from the Navigator to any text editor, or copy sections of LD logic as text from the LD editor to any text editor. You can then edit the logic in the text editor and copy the edited logic back into the LD editor. 70 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors LD Editor When LD logic is copied as text, a verbose format is used to make it easier to read, but when you edit the logic as text you can use the same shorthand used in the keyboard method of entering LD logic in the LD editor. T o co p y a n e nt ir e LD b lo ck as t ex t 1. Validate the 2. In the target to ensure that the LD block contains only valid logic. Project tab of the 3. Expand the Navigator, expand the target and expand the Program Blocks folder and, if the LD block is in a Logic folder. user-defined folder, expand the user-defined folder. 4. Right-click the LD block and choose Copy. The contents of the LD block are copied to the Windows Clipboard. 5. Paste the contents of the Windows Clipboard into your text editor. The LD logic is pasted as text. T o co p y a s e ct ion o f L D lo gic a s te x t 1. Validate the target to ensure that the LD block contains only valid logic. 2. In the LD editor, select the cells that contain the logic you want to copy as text. 3. Right-click the selected logic and choose Copy. The LD logic is copied to the Windows Clipboard. 4. Paste the contents of the Windows Clipboard into your text editor. The LD logic is pasted as text. T o co p y te x t i nto t he L D e di to r 1. In the text editor, select and copy the LD logic to the Windows clipboard. 2. In the LD editor, do one of the following: ■ Select the cells that you want to overwrite. - OR ■ Click the cell that will be the upper left corner of the LD logic you want to paste. 3. Right-click and choose Paste. Existing cells in the LD editor are overwritten with the contents of the Windows clipboard. Want to know more? In the Help Index, look up “Copying LD Logic as Text: Overview”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 71 Logic Editors 5 LD Editor Working with the LD Editor Online In online mode, there is a live communication connection to the target PLC enabling increased interaction with Logic Developer - PLC. While online, the LD editor animates the LD logic to reflect program execution in the target PLC. Data values change in real time while coils and contacts indicate power flow. Many GE Fanuc targets also supports Run Mode Store (RMS), that is, they support the downloading of logic to a running target. Three methods are at your disposal to make changes in your LD logic and download the changes to an online running PLC: ■ Online Editing (PACSystems™ only): While you make your changes in your logic, the LD editor displays both the original logic and the modified logic, and the PACSystems™ executes the original logic. You can test your changes online, and the PACSystems™ retains an inactive copy of the original logic while executing the modified logic. You can then commit the modified logic permanently to the PACSystems™, or make the PACSystems™ revert back to the original logic, or cancel the test and continue editing the logic before testing the logic again or abandoning the modified logic. ■ Word-for-word changes: Changes in the logic made while online that fit in the same amount of memory as the original logic. For example, changing an operand is usually a word-for-word change. You can make a word-for-word change and download it to the PLC while online without having to download all the logic. ■ Other logic changes: Changes in the logic that do not fit in the same amount of memory as the original logic, for example, adding a new function in a rung or adding a new rung. Once you have completed a change, you can write the modified logic to the PLC while it is still running. (For some types of changes, you must stop the PLC and then download to it.) T o go o nli ne to a t ar g e t P LC • In the Project tab of the Navigator, right-click the Target and choose Go Online. The grey target icon turns green to indicate that it is online. The status bar is updated to reflect the online status. The LD editor, if equal to the PLC, displays various online features, as shown in the following illustration: 72 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors LD Editor Rung Number State Flow is indicated by bolded lines. Online Status is indicated by the color of the target icon. A red, underlined variable indicates that it has been forced ON. Right-click a variable to force it. Online indicator PLC status and sweep time are displayed in real-time in the Inspector. Monitor and change values in real-time with the Data Watch tool. Feedback Zone PLC status is indicated in the status bar. Word-for-W ord Changes Word-for-word changes may be completed online to PACSystems™, Series 90™30, Series 90™-70, Series 90™ Micro, and VersaMax® modular PLCs. (VersaMax Nano/ Micro PLCs do not support word-for-word changes.) Several of the changes to the program that do not modify its size are considered word-for-word changes. Examples include changing the type of contact or coil, or changing a reference address used for an existing function block. T o ma ke wo rd - for - wo rd c ha ng es 1. While online to a target PLC, make a change to LD logic that does not change the logic size. You are prompted to download the change. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 73 5 Logic Editors LD Editor 2. Click Yes. The changes are written to the PLC. Writing Changes to a Target P LC If you change the size of the program, you must write the changes to the PLC to maintain equality. You can do so whether the target is running or not. All PLC families support this run-mode store capability, but not every PLC in every family. T o wr i te c ha ng e s to th e ta r ge t PL C 1. While online to a target, make a change to LD logic. 2. In the Project tab of the Write Changes. Navigator, right-click the target, point to Online Commands, and choose New logic is immediately written to the PLC without stopping the PLC. If the LD logic was altered, other than a word-for-word change, you are prompted to download to the running PLC. The entire target is validated, but only the changed blocks are downloaded. T o tur n on/ of f o r for c e a va ria bl e • In the LD editor, right-click a BOOL variable anywhere in LD logic and choose Force ON, Force OFF, Turn ON, or Turn OFF. Note: Forcing a variable ON or OFF overrides any actions the application may take during runtime. That is, if a variable is forced OFF (0), but LD logic is trying to turn it ON (1), it stays OFF. Want to know more? In the Help Index, look up “Online Editing: an Overview” and “working online with LD editor: overview". 74 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors LD Editor LD Functions The following is a list of all LD functions available in Logic Developer - PLC. An asterisk followed by the letter P (*p) indicates the functions exclusive to PACSystems™ PLCs. An asterisk followed by "70" (*70) indicates the functions exclusive to Series 90™-70 PLCs. A simple asterisk (*) indicates the functions shared by PACSystems™ and Series 90™-70 PLCs and exclusive to them. Companion help indicates which PLCs support the other functions. Want to know more? In the Help Index, look up “LD Functions”. Ad va nc e d Mat h ACOS COS LN SQRT_DINT ASIN EXP LOG SQRT_INT ATAN EXPT SIN SQRT_REAL TAN Bit Op era tio ns AND_DWORD* BIT_SET_DWORD* NOT_WORD SHIFTL_DWORD* AND_WORD BIT_SET_WORD OR_DWORD* SHIFTL_WORD BIT_CLR_DWORD* BIT_TEST_DWORD* OR_WORD SHIFTR_DWORD* BIT_CLR_WORD BIT_TEST_WORD ROL_DWORD* BIT_POS_DWORD* MASK_COMP_DWORD ROL_WORD XOR_DWORD* BIT_POS_WORD MASK_COMP_WORD ROR_DWORD* XOR_WORD BIT_SEQ NOT_DWORD* ROR_WORD SHIFTR_WORD Co ils COIL NEGCOIL p PTCOIL*p CONTCOIL NTCOIL* RESETCOIL NCCOIL POSCOIL SETCOIL CONTCON LOALR* NOCON POSCON* FAULT* NCCON NOFLT* PTCON*p HIALR* NEGCON* NTCON*p Co nta ct s GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 75 Logic Editors 5 LD Editor Co ntr o l DO_IO EXIT_FOR* PID_ISA DRUM FOR_LOOP* SER END_FOR* PID_IND SUS_IO* SVC_REQ Co nve r sio ns BCD4_TO_INT DINT_TO_BCD8* INT_TO_REAL REAL_TO_WORD UINT_TO_REAL* BCD4_TO_REAL DINT_TO_INT* INT_TO_UINT* TRUNC_DINT WORD_TO_REAL BCD4_TO_UINT* DINT_TO_REAL RAD_TO_DEG TRUNC_INT BCD8_TO_DINT* DINT_TO_UINT* REAL_TO_DINT UINT_TO_BCD4* BCD8_TO_REAL* INT_TO_BCD4 REAL_TO_INT UINT_TO_DINT* DEG_TO_RAD INT_TO_DINT* REAL_TO_UINT* UINT_TO_INT* Co unt er s DNCTR UPCTR D at a M ove BUS_TS_BYTE* P BLK_CLR_WORD BLKMOV_DINT* BUS_TS_DWORD* BLKMOV_DWORD* BUS_WRT_BYTE* P P DATA_INIT_UINT* SWAP_WORD* DATA_INIT_WORD* VME_CFG_READ*70 MOVE_BOOL VME_CFG_WRITE*70 MOVE_DINT* VME_RD_BYTE* 70 BLKMOV_INT BUS_WRT_DWORD* BLKMOV_REAL BUS_WRT_WORD* P MOVE_DWORD* VME_RD_WORD* 70 BLKMOV_UINT* COMM_REQ MOVE_INT VME_RMW_BYTE* 70 BLKMOV_WORD DATA_INIT_ASCII* MOVE_REAL VME_RMW_WORD* 70 DATA_INIT_COMM* MOVE_UINT* VME_TS_BYTE* 70 BUS_RD_DWORD* P DATA_INIT_DINT* MOVE_WORD VME_TS_WORD* 70 BUS_RD_WORD* P DATA_INIT_DLAN*70 SHFR_BIT VME_WRT_BYTE* 70 DATA_INIT_DWORD* SHFR_DWORD* VME_WRT_WORD* 70 DATA_INIT_INT* SHFR_WORD DATA_INIT_REAL* SWAP_DWORD* BUS_RD_BYTE* P BUS_RMW_BYTE* P BUS_RMW_DWORD* BUS_RMW_WORD* 76 P P P CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors LD Editor D at a T a bl e ARRAY_MOVE_BOOL FIFO_WRT_WORD* SEARCH_GE_UINT* SEARCH_NE_DINT ARRAY_MOVE_BYTE LIFO_RD_DINT* SEARCH_GE_WORD SEARCH_NE_DWORD* ARRAY_MOVE_DINT LIFO_RD_DWORD* SEARCH_GT_BYTE SEARCH_NE_INT ARRAY_MOVE_DWORD* LIFO_RD_INT* SEARCH_GT_DINT SEARCH_NE_UINT* ARRAY_MOVE_INT LIFO_RD_UINT* SEARCH_GT_DWORD* SEARCH_NE_WORD ARRAY_MOVE_UINT* LIFO_RD_WORD* SEARCH_GT_INT SORT_INT* ARRAY_MOVE_WORD LIFO_WRT_DINT* SEARCH_GT_UINT* SORT_DINT* ARRAY_RANGE_DINT* LIFO_WRT_DWORD* SEARCH_GT_WORD SORT_WORD* ARRAY_RANGE_DWORD* LIFO_WRT_INT* SEARCH_LE_BYTE TBL_RD_DINT* ARRAY_RANGE_INT* LIFO_WRT_UINT* SEARCH_LE_DINT TBL_RD_DWORD* ARRAY_RANGE_UINT* LIFO_WRT_WORD* SEARCH_LE_DWORD* TBL_RD_INT* ARRAY_RANGE_WORD* SEARCH_EQ_BYTE SEARCH_LE_INT TBL_RD_UINT* FIFO_RD_DINT* SEARCH_EQ_DINT SEARCH_LE_UINT* TBL_RD_WORD* FIFO_RD_DWORD* SEARCH_EQ_DWORD* SEARCH_LE_WORD TBL_WRT_DINT* FIFO_RD_INT* SEARCH_EQ_INT SEARCH_LT_BYTE TBL_WRT_DWORD* FIFO_RD_UINT* SEARCH_EQ_UINT* SEARCH_LT_DINT TBL_WRT_INT* FIFO_RD_WORD* SEARCH_EQ_WORD SEARCH_LT_DWORD* TBL_WRT_UINT* FIFO_WRT_DINT* SEARCH_GE_BYTE SEARCH_LT_INT TBL_WRT_WORD FIFO_WRT_DWORD* SEARCH_GE_DINT SEARCH_LT_UINT* FIFO_WRT_INT* SEARCH_GE_DWORD* SEARCH_LT_WORD FIFO_WRT_UINT* SEARCH_GE_INT SEARCH_NE_BYTE Ma th GFK-1918D ABS_DINT* ADD_UINT* MOD_DINT MUL_REAL SUB_REAL ABS_INT* DIV_DINT MOD_INT MUL_UINT* SUB_UINT* ABS_REAL* DIV_INT MOD_UINT* SCALE_INT ADD_DINT DIV_MIXED* MUL_DINT SCALE_WORD ADD_INT DIV_REAL MUL_INT SUB_DINT ADD_REAL DIV_UINT* MUL_MIXED* SUB_INT CIMPLICITY Logic Developer - PLC Version 4.00 77 5 Logic Editors LD Editor Pr og r am Flo w CALL ENDMCR JUMP LABELN COMMENT ENDMCRN JUMPN MCR END H_WIRE LABEL MCRN V_WIRE R el at ion al CMP_DINT* EQ_UINT* GT_REAL LT_INT RANGE_DINT CMP_INT* GE_DINT GT_UINT* LT_REAL RANGE_DWORD* CMP_REAL* GE_INT LE_DINT LT_UINT* RANGE_INT CMP_UINT* GE_REAL LE_INT NE_DINT RANGE_UINT* EQ_DINT GE_UINT* LE_REAL NE_INT RANGE_WORD EQ_INT GT_DINT LE_UINT* NE_REAL EQ_REAL GT_INT LT_DINT NE_UINT* T i me r s 78 OFDT_HUNDS ONDTR_HUNDS TMR_HUNDS OFDT_SEC* ONDTR_SEC* TMR_SEC* OFDT_TENTHS ONDTR_TENTHS TMR_TENTHS OFDT_THOUS ONDTR_THOUS TMR_THOUS CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors IL Editor IL EDITOR Instruction List (IL) is a programming language specified by the IEC 61131-3 standard. This text language is accumulator-based and much like the assembly languages used for programming microprocessors. The instructions executed by the IL program modify or use an accumulator that is located in PLC memory. Two types of accumulators are defined: one analog accumulator for numeric and bitwise operations and eight boolean accumulators for discrete logic to support eight levels of nested boolean expressions. The IL editor is free-form with an option to apply a standard formatting rule. The appearance and behavior of the IL editor is user-configurable. Navigator: Project tab An IL Block Note: Only Series 90™-30, VersaMax PLCs, and VersaMax Nano/Micro support IL logic. T o co nf i g ur e a cc um ula to rs 1. In the Project tab of the Navigator, right-click the Program Blocks folder and choose Properties. The Inspector opens, displaying the Accumulator Address properties. 2. In the Boolean Start property, enter the reference address of the first of eight PLC memory locations to use for boolean accumulators. The ending address is calculated automatically. The memory area must be %T, %M, or %Q. 3. In the Analog Start property, enter the PLC memory locations to use for the analog accumulator. The ending address is calculated automatically. The memory area must be %R, %AI or %AQ. T o cr e at e a n I L blo c k 1. In the Projects tab of the Navigator, right-click the Program Blocks folder, point to New, and choose IL Block. An empty IL block with the default name ”ILBkn” is added to the folder, where n represents a unique number. 2. Rename the block as desired. T o op e n a n IL b loc k f o r e di ti ng • In the Project tab of the Navigator, right-click an IL Block and choose Open. The block opens in the IL editor. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 79 5 Logic Editors IL Editor Note: You can have multiple blocks open for editing. To navigate to another open IL block, click the tab displaying its name at the bottom of the editor window. Working with the IL Editor Offline Most project development is carried out while offline from the target PLC. Editing while offline provides maximum flexibility in editing and allows you to interact with the Machine Edition tools as shown in the following diagram. The Variables tab of the Navigator lists all the variables in your projects. Right click in the IL Editor to insert an instruction or variable. Drag and drop variables from the Variables list into the IL editor. A description of a variable pops up when you hover the mouse over it. Configure the accumulators in the Inspector. The Build tab of the Feedback Zone lists error messages when you validate. The Companion tracks all of your moves and provides information on what you click. To ins e rt a n in st ruc t ion o r func tio n 1. In the IL editor, right-click and choose Insert Keyword. A smart list appears listing all available instruction mnemonics. 2. From the list, select an instruction and press ENTER. The instruction is inserted in your logic. T o as s ign o pe r an ds t o an ins tr uc tio n 1. In the IL editor, right-click and choose Insert Variable. A smart list appears showing all your defined variables. 80 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors IL Editor 2. Type, or choose from the list, a variable name or reference address and then press ENTER. The name appears in your logic. Note: If you entered a reference address or a new variable name, you must create a variable from it. T o cr e at e a va ri ab le fr om a r e fe re n ce a d dr e ss 1. In the IL editor, right-click a reference address, point to Create “name” as, and then choose a data type. A variable is created and a default name is applied. For example, if the reference address is %R0032, the auto-created variable is named R00032. T o cr e at e a va ri ab le f r om a na me 1. In the IL editor, right-click a name, point to Create “name” as, and then choose a data type. A variable is created with the name you right-clicked. 2. Map the variable to PLC memory. (See page 17.) T o mo ve o r du plic a te I L lo gic 1. In the IL editor, select a range of logic. 2. To move it, click the selection and drag it to a new location. To duplicate it, press CTRL while clicking the selection, and drag the selection to where you want to place the duplicate. When you release the mouse button, the selection is respectively moved to the new location or a duplicate copy of the selected logic is placed in the new area. To ins e rt a n in line c o mme n t 1. In the IL editor, click where you want to insert an inline comment. 2. Type an apostrophe (‘) followed by comment text. Press ENTER to complete the comment. T o i ns e rt a bl oc k c om me nt 1. In the IL editor, click where you want to insert a block comment. 2. Type (* followed by comment text. A block comment can contain any number of characters and can span multiple lines. 3. Type *) to complete the block comment. T o re fo r ma t I L c od e • In the IL editor, right-click and choose Beautify Source. The entire content of the IL editor is reformatted according to the default formatting (indentation) rules. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 81 5 Logic Editors IL Editor Working with the IL Editor Online While online to a target PLC, the IL editor enables you to edit logic, monitor data values, and change or force the state of BOOL variables in real-time. This allows you to test the execution of logic, to trigger an event within an executing project, or to remove an element from logic execution. Target icon changes to indicate status of the PLC. Hover over a variable to show a popup of its value. Right-click a BOOL to change or force its state. The Feedback Zone indicates that a connection has been established with the PLC. The Companion tracks your moves and provides information on what you click. Monitor and change variable values in the Data Watch. PLC status is indicated in the status bar. T o mo nit or a d at a v alu e • Click anywhere in the IL editor and hover the mouse pointer over a variable. A tooltip appears, showing the variable’s current value. This value, however, does not update. You must move the mouse pointer away and back over the variable. T o ch ang e a BO OL va r iab le ’s s ta te • In the IL editor, right-click the BOOL variable whose value you want to change and choose Turn On or Turn Off. The state of the variable in the target PLC changes when the command is received. It remains in that state until acted on by the PLC’s logic. 82 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors IL Editor T o for c e a BOO L va ria b le ’s st at e • In the IL editor, right-click a BOOL variable and choose Force On or Force Off. The state of the forced variable will remain unchanged, regardless of any actions by the PLC’s logic. To re m ov e the for c e fr om a BO OL va ri ab le • In the IL editor, right-click a BOOL variable and choose Remove Forces. The state of the forced variable will be controlled by the PLC’s logic. Writing Changes to a Target P LC You can change your IL logic while online, but you must write the changes to the PLC to maintain equality. Writing changes to a target PLC requires the PLC to be online and running. Note: If you go offline, you can do a regular download. T o wr i te c ha ng e s to th e ta r ge t PL C ( i f th e ta r ge t PL C s up po r ts i t ) 1. While online to a target PLC, make a change to IL logic. 2. In the Project tab of the Write Changes to PLC. Navigator, right-click the target, point to Online Commands, and choose You are prompted to confirm a Run Mode Store. That is, the altered IL block will be downloaded to the PLC without stopping the PLC. Want to know more? In the Help Index, look up “Writing Changed Logic to the PLC” GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 83 5 Logic Editors IL Editor IL Instructions and Functions The following is a list of all IL instructions and functions available in Logic Developer - PLC. An asterisk (*) indicates the functions exclusive to VersaMax® PLCs. Companion help indicates which PLCs support the other functions. Bas ic I ns tr uc tio ns ADD CAL GT MOD NT R SUB XORN AND DIV LE MUL OR RET AND_WORD EQ LT NE ORN RETC ANDN GE MCRN NOT PT S TAN Ad va nc e d Mat h ACOS COS LN SQRT_INT ASIN EXP LOG SQRT_DINT ATAN EXPT SIN SQRT_REAL Bit Op era tio ns AND_WORD BIT_SEQ MASK_COMP_DWORD OR_WORD BIT_CLR_WORD BIT_SET_WORD MASK_COMP_WORD ROL_WORD BIT_POS_WORD BIT_TEST_WORD NOT_WORD ROR_WORD SHIFTL_WORD Co ntr o l DO_IO PID_ISA DRUM SER PID_IND SVC_REQ Co nve r sio ns BCD4_TO_INT DINT_TO_REAL RAD_TO_DEG REAL_TO_WORD BCD4_TO_REAL INT_TO_BCD4 REAL_TO_DINT TRUNC_DINT DEG_TO_RAD REAL_TO_INT TRUNC_INT INT_TO_REAL WORD_TO_REAL Co unt er s DNCTR 84 UPCTR CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors IL Editor D at a M ove BLK_CLR_WORD BLKMOV_INT BLKMOV_REAL BLKMOV_DINT COMM_REQ MOVE_INT MOVE_BOOL MOVE_REAL SHFR_BIT MOVE_WORD SHFR_WORD D at a T a bl e ARRAY_MOVE_BOOL SEARCH_EQ_INT ARRAY_MOVE_BYTE SEARCH_EQ_WORD SEARCH_GT_INT ARRAY_MOVE_DINT SEARCH_GE_BYTE SEARCH_GT_WORD SEARCH_LT_INT ARRAY_MOVE_INT SEARCH_GE_DINT SEARCH_LE_BYTE SEARCH_LT_WORD SEARCH_LE_DINT SEARCH_NE_BYTE ARRAY_MOVE_WORD SEARCH_GE_INT SEARCH_GT_DINT SEARCH_LT_BYTE SEARCH_NE_WORD SEARCH_LT_DINT SEARCH_EQ_BYTE SEARCH_GE_WORD SEARCH_LE_INT SEARCH_NE_DINT SEARCH_EQ_DINT SEARCH_GT_BYTE SEARCH_NE_INT SEARCH_LE_WORD Mat h ADD_DINT DIV_DINT MOD_DINT MUL_DINT SCALE_WORD* SUB_REAL ADD_INT DIV_INT MOD_INT MUL_REAL SUB_DINT ADD_REAL DIV_REAL MUL_INT SCALE_INT* SUB_INT CALL ENDMCR JUMP LABELN COMMENT ENDMCRN JUMPN MCR END H_WIRE LABEL MCRN EQ_DINT GE_DINT GT_DINT LE_DINT LT_DINT NE_DINT RANGE_DINT EQ_INT GE_INT GT_INT LE_INT LT_INT NE_INT RANGE_INT EQ_REAL GE_REAL GT_REAL LE_REAL LT_REAL NE_REAL RANGE_WORD Pr og r am Flo w V_WIRE R el at ion al T i me r s OFDT_HUNDS ONDTR_HUNDS TMR_HUNDS OFDT_TENTHS ONDTR_TENTHS TMR_TENTHS OFDT_THOUS ONDTR_THOUS TMR_THOUS GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 85 5 Logic Editors C Blocks C BLOCKS A C block is an independent section of executable code written in the C programming language, that is downloaded to and executed on the target PLC. C blocks are created externally using GE Fanuc’s C Programming Toolkit and then imported into a project. A C block compiled for PACSystems™ has a .gefelf extension. A C block compiled for Series 90™-70 or Series 90™-30 has a .exe extension. C Blocks can be called as a subroutine from another block (LD or IL) but cannot call another block. Navigator: Project tab For more information on developing C Blocks, refer to C Programmer’s Toolkit for Series 90 PLCs (GFK-0646) and PACSystems RX7i C Toolkit User’s Guide (GFK2259). A C Block Working with C blocks T o imp or t a C b lo ck 1. In the Projects tab of the Navigator, right-click the Program Blocks folder and choose Add C block. The Open dialog box appears. 2. Browse to the .exe or .gefelf file you want to import and click Open. The selected file is added to the the .exe or gefelf file. Program Blocks folder with the same name as Note: You can then move the C Block to a user-defined folder. Want to know more? In the Help Index, choose “C” and "User-Defined Folder". 86 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors C Blocks T o se t a C b lo ck ’s p a ra me te r s Note: This procedure applies only to PACSystems™ and to Series 90™-70 targets and to C blocks that were written to require parameters. 1. In the The Projects tab of the Navigator, right-click the C block and choose Properties. Inspector displays the block’s properties. 2. In the Inspector, select the Parameters property and click . The Parameters dialog box opens. 3. Type a name and description for each required input and output parameter. For information on the required parameters, consult the written documentation for the C block. The names you enter will display in the CALL instruction. The names and descriptions will display as tooltip help when you hover over the CALL instruction. Want to know more? In the Help Index, enter “Parameterized” and select the “C Block” help topic. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 87 5 Logic Editors C Programs C PROGRAMS Note: C programs are supported only on Series 90™-70 CPUs, firmware release 6.00 and later. A C program is an independent section of executable code, written in C language, that is downloaded to and executed on the associated target PLC. To develop a C program, use GE Fanuc's C Programmer's Toolkit for Series 90 PLCs User's Manual (GFK-0646). You then import it into a project. Navigator: Project Tab A C Program A C program has access to all the % reference tables of the PLC except for the _MAIN LD block’s %P memory and the %L memory of any other LD block. A C program can also call any of the numerous PLC-embedded function blocks, which are included in the C Programmer’s Toolkit. A C program cannot be called as a subroutine. Execution is controlled only through scheduling. A C program cannot call another block as a subroutine. By setting the parameters of a C program, you enable it to access memory directly. When a C program begins to execute, it reads the data for all the parameters and makes a copy of the data. If the C program’s execution is interrupted or time-sliced over multiple scans, the C program, when it resumes execution, uses the copy of the data that it made upon beginning to execute. You can add C programs to a Series 90™-70 target only if the _MAIN block is an LD block. The LD program is then treated as a user program, which can be scheduled. The maximum number of C programs you can add is 15. If you have State Logic on a Series 90™-70 target, it is compiled into a C Program called _STATE, whether State Logic coexists with LD logic or not. If State Logic does not coexist with LD logic, _STATE is the only C program supported by the target. C programs can coexist with State Logic on a Series 90™-70 PLC. For such a target, the State Logic is compiled into a C program. This C program is named _MAIN if there is no LD logic; however, if State Logic coexists with LD logic, the State Logic is compiled into a C program named _STATE and one LD block must be named _MAIN. User Programs User programs consists of: ■ C programs ■ 88 The LD program, if the _MAIN block is an LD block. CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Logic Editors C Programs Working with User Program s T o co nf i g ur e e x e cut i o n s c he du ling 1. In the Projects tab of the Properties. The Navigator, right-click a C program or the _MAIN LD block, and choose Inspector displays the user program’s properties. 2. In the Inspector, expand the Scheduling property. 3. Select a Schedule Mode. 4. Select the other properties used in the schedule mode you selected. 5. Click OK. Note: If you made any entries, they are checked when you click OK. You must correct any errors before you can close the dialog box by clicking the OK button. S et tin g a C p ro g ra m’s p a ra me t er s Note: You must provide a list of all the input and output parameters that the C program requires. The LD program does not use parameters. 1. In the The Projects tab of the Navigator, right-click a C program and choose Properties. Inspector displays the C program’s properties. 2. In the Inspector, select the Parameters property and click . The Parameters dialog box opens. 3. On the Input and Output tabs, enter up to 8 input and up to 8 output parameters. Each parameter has its own row on the tab. For each parameter, double-click the following cells and enter the required data: ■ Name: The parameter’s name. ■ Type: The parameter’s data type. ■ Length: The length of the input or output reference. ■ Variable: The first data item associated with the parameter. ■ Description: (Optional) The parameter’s description. Want to know more? In the Help Index, choose “C Program”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 89 6 Motion Programming Logic Developer - PLC supports motion programming for the Motion Mate DSM314 motion control module. A high performance, easy-to-use, multi-axis motion control module, the Motion Mate DSM314 is highly integrated with the Series 90™-30 PLC logic solving and communication functions. The DSM314 (see page 55) supports 10 motion programs, 40 subroutines and a maximum total of 1000 motion program statements. Logic Developer - PLC, making motion programming possible, supports the following motion editors: PLC Motion Editor Local Logic Editor CAM Editor Navigator: Project tab This chapter outlines basic procedures that will get you started with Logic Developer - PLC to create motion programs, using these three motion editors. Motion Program nodes T o ad d a Mot io n c om po ne n t t o a ta rg e t • In the Project tab of the Navigator, right-click the target, point to Add Component and then choose Motion. A Motion Program node is added to your project. Included are empty Motion Blocks, Local Logic, CAM Profiles and CAM Blocks folders. Target right-click menu CIMPLICITY Logic Developer - PLC Version 4.00 91 6 Motion Programming PLC Motion Editor PLC MOTION EDITOR Logic Developer - PLC includes a PLC Motion Editor, which enables you to create PLC Motion blocks for the DSM314. This text-based editor is configurable as to its appearance and behavior. Comments and white space are not considered as PLC Motion program statements. Motion programming has a different programming syntax from Local Logic. T o ad d a Mot io n Blo c k 1. In the Project tab of the 2. Right-click the Navigator, expand the Motion Program folder. Motion Blocks folder and choose New. A new empty PLC Motion block with a default name is added to your project. 3. Rename the block as desired. Navigator: Project tab Motion Blocks T o op e n a m ot io n b lo ck f o r e di ti ng • In the Project tab of the Navigator, right-click the Motion Block node and choose Open. The block opens for editing in the PLC Motion editor 92 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Motion Programming PLC Motion Editor Working with the Motion Editor T o ins e rt a c om ma nd 1. In the Motion editor, right-click and choose Insert Keyword. A smart list appears showing all available motion commands. 2. Select the appropriate command from the smart list and press ENTER. The command is placed in the motion editor. Insert a PLC Motion command by choosing a keyword. Insert a PLC Motion variable by selecting a variable from the smart list. The Companion tracks all mouse clicks. The Feedback Zone indicates that a connection has been established with the PLC. Want to know more? In the Help Index, choose “PLC Motion Editor”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 93 6 Motion Programming PLC Motion Editor Motion Commands ACCEL BLOCK NUMBER CAM CAM-LOAD CAM-PHASE CALL CMOVE DWELL ENDPROG ENDSUB JUMP LOAD PMOVE PROGRAM SUBROUTINE SYNC BLOCK VELOC 94 CIMPLICITY Logic Developer - PLC Version 4.00 The ACCEL statement sets the axis acceleration for subsequent moves and remains in effect in a given program unless changed. Note: If a move instruction is executed before ACCEL, the tag Acceleration is used. Block numbers may be used as the destination of JUMP commands. Block numbers must be unique and can be between 1 and 65535. The CAM statement starts CAM motion and specifies exit conditions. CAM-LOAD loads a parameter register with the starting location for a CAM slave axis. CAM-PHASE sets the phase for CAM commands. The CALL command executes another block as a subroutine The CMOVE command programs a continuous move using the specified position and acceleration mode. DWELL causes motion to cease for a specified time period before processing the next command. The ENDPROG statement terminates a PLC Motion program definition. The ENDSUB statement terminates a PLC Motion subroutine definition. Jump to a block number or a sync block within the current program or subroutine. The jump may be unconditional or conditional based on the status of a CTL bit. Initializes or changes a parameter data register with a 32-bit twoscomplement integer value. The PMOVE command programs a positioning move using the specified position and accelerator mode. The PROGRAM statement is the first statement in a motion program. The program statement identifies the program number (1-10) and the axis configuration. Program definitions cannot nest. The SUBROUTINE statement is the first statement in a motion subroutine. The subroutine statement identifies the subroutine number (1-40) and the axis configuration. A sync block is a special case of a block number. A sync block may only be used in multi-axis programs. Sets the process VELOCITY used by subsequent motion program move commands and remains in effect until changed by another VELOC statement. GFK-1918D Motion Programming Local Logic LOCAL LOGIC A Local Logic program runs synchronously with the Motion program, but is independent of the PLC’s CPU scan. This allows the DSM314 to interact much more quickly with motion I/O signals on its faceplate connectors than would be possible if the logic for the signals was handled in the main ladder program running on the PLC. Local Logic language uses free-form, text-based circuits and contains basic mathematical and logical constructs. Local Logic programming syntax allows you to assign a variety of logic tasks to your motion programs while working in conjunction with PLC Logic programs and motion programs to yield a flexible programming environment. Because it uses straightforward, understandable syntax, it is easy to gain proficiency with this editor. The Local Logic programming language supports assignments, conditional statements, arithmetic, logical and relational statements. Local Logic provides the user access to motion controller data, parameters using a fixed set of variables, control and status bits. Navigator: Project tab Local Logic ■ Parameter data - accessible from Local Logic host PLC and motion programs. The parameter data are similar to variables in a program. ■ CTL bits - allow the Local Logic program or host PLC to signal the motion program to start an event. ■ Motion program block numbers - the current block number can be used within the Local Logic program or host PLC to make an action occur only during a specific motion programming section. T o cr e at e a L oc al Lo g ic bl oc k 1. In the Projects tab of the A new Navigator, right-click the Local Logic folder and choose New. Local Logic block with a default name is created. 2. Rename the block as required. T o op e n a L o ca l L og ic b lo ck fo r e d iting • In the Projects tab of the Navigator, right-click the Local Logic block and choose Open. The Local Logic block opens in the Local Logic editor and is ready for editing. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 95 6 Motion Programming Local Logic Working with Local Logic Editor The Local Logic editor has its own distinctive syntax for constructing Local Logic programs. Navigator shows the organization of your project. Drag and drop variables from the Local Logic Variable table into the Local Logic editor. Right-click to choose commands from a list. T o ins e rt a Lo c al Lo g ic co m man d 1. In the Local Logic editor, right-click and choose Insert Keyword from the menu. A smart list appears showing all available Local Logic commands. 2. Select the desired command in the smart list and press ENTER The command is inserted. Note: You can drag variables from the Local Logic Variable Table to the Local Logic editor. 96 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Motion Programming Local Logic Local Logic Variables Local Logic is designed to complement a PLC’s logic and mathematical capabilities. Solving small Local Logic and mathematical sets require a tight synchronization with the controlled motion. Logic Developer - PLC includes a table containing Local Logic variables, the Local Logic Variable Table (LLVT), that you can drag into your logic programs. As illustrated in the diagram below, the LLVT has several tabs that organize the variables by category: Click a heading to sort the table in ascending order. Click again to sort descending. Right-click a name to copy it to the clipboard. Click a tab to view a group of variables T o vie w t he L L VT 1. In the InfoViewer tab of the Navigator, expand the Logic Developer - PLC library then expand the Local Logic Editor book and double-click Local Logic Variable Table. The LLVT appears in the Infoviewer. The variables or data in each tab are: Axis 1 Axis 2 Axis 3 Axis 4 Global CTL bits Parameter Registers GFK-1918D Variables specific to axis 1 Variables specific to axis 2 Variables specific to axis 3 Variables specific to axis 4 Global data such as module status code DSM general Control/Status bits DSM parameter data CIMPLICITY Logic Developer - PLC Version 4.00 97 Motion Programming 6 Local Logic The table has six columns: Name Type Group Description R W Contains the variable name that is to be used within a Local Logic program The data type for this variable. For example, 32-bit means that this variable is a 32-bit variable. The group this variable is placed in. For example, Faceplate I/O means that this variable refers to a point on the module faceplate. This column contains a textual description of the variable. When the user hovers the mouse pointer over the description, a tool tip displays the description. This column indicates if the variable can be read by a Local Logic program. This column indicates if the variable can be written by a Local Logic program. T o ins e rt a Lo c al Lo g ic va ria bl e 1. In the Local Logic editor, right-click and choose Insert Variable. A smart list appears prompting you to choose a Local Logic variable name. 2. Select a variable in the list and press ENTER. The variable is inserted in your Local Logic. 98 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Motion Programming Local Logic Local Logic Commands and Operators Local Logic enables you to execute basic logic and mathematical functions on the DSM module. Commands use upper case characters only and are case sensitive. ABS BWAND BWOR BWXOR BWNOT ON OFF TRUE FALSE IF THEN END_IF MOD + plus -(minus) / (divide) * (multiply) :=(assign) >(greater than) < (less than) >= (greater than or equal to) <= (less than or equal to) <> (not equal) Want to know more? In the Help Index, choose “Local Logic: an Overview”. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 99 6 Motion Programming CAM Editor CAM EDITOR The CAM editor is an accessory for Logic Developer - PLC motion programming that provides a means to create, edit, and manage electronic CAM profiles. Each CAM profile is a curve that specifies the response of a slave servo to a master position index. CAM profiles are referenced by name in the associated motion program and grouped into CAM blocks. Each block is intended for download to a specific motion module by means of a PLC controller. The hardware components are specified in the HWC for the associated project. CAM profiles are user-defined in a library and then grouped into blocks by aliasing them. This allows you to reuse CAM profiles by including them in multiple CAM blocks. Project Tab: Navigator CAM Blocks T o cr e at e a CA M b lo ck 1. In the Project tab of the 2. Right-click the Navigator, expand the Motion Program folder. CAM blocks folder and choose New. A new CAM block with a default name is created. 3. Rename the block as desired. T o imp or t CA M b lo ck s 1. In the Project tab of the 2. Right-click the Navigator, expand the Motion Program folder. CAM blocks folder and choose Import from File. The Open dialog box appears. 3. Browse to the CAM block you want to import (.csv or .txt file). 4. Click Open. The imported block appears in your project. 100 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Motion Programming CAM Editor Working with the CAM Editor You can adjust the curves of your CAM profile to suit the specific needs of your project. With the CAM editor you create profiles by defining points on a master/slave position curve. Groups of adjoining points are allocated to sectors. Each sector is assigned a polynomial curve fit order (1,2,3) that specifies how the curve will be interpolated between points. Curves of the profile can be adjusted and edited graphically. Navigator displays CAM profiles and blocks. CAM profile table allows numeric editing and curve order grouping Secondary curves show the velocity, acceleration and jerk of the CAM profile. Configure profiles and blocks in the Inspector. The Companion tracks your moves and provides information on what you click. T o cr e at e a CA M p r of i l e • In the Project tab of the Navigator, right-click the CAM Profiles folder and choose New. A new CAM profile with a default name is added to your project. To co nfig ur e a CA M pr of ile 1. In the Project tab of the Navigator, right-click a CAM profile and choose Properties. The Inpector displays the properties of the CAM profile. 2. Adjust the properties of the CAM profile in the Inspector to specify its type and boundary conditions. GFK-1918D CIMPLICITY Logic Developer - PLC Version 4.00 101 6 Motion Programming CAM Editor To edit a CA M p ro fil e 1. In the Project tab of the Navigator, expand the Motion Program folder and double-click a CAM profile. A graphical representation of your profile appears in the profile editor and a numeric representation appears in the profile table. 2. Insert and move points in the profile editor or table. 3. Group points into sectors in the profile table and assign curve fit order to each sector. T o ad d an al ias t o a C AM bl oc k • In the Project tab of the Navigator, right-click a CAM block, point to Add Alias to, and then choose a profile. Note: Aliases correspond to CAM profiles within CAM blocks. In order to create aliases for CAM blocks, you must have previously created CAM profiles. Want to know more? In the Help Index, choose “CAM”. 102 CIMPLICITY Logic Developer - PLC Version 4.00 GFK-1918D Index Index A Access Control Setting 65 Accumulators Configuring 79 Adding Carrier/Base to VersaMax Remote I/O 60 DSM314 Motion Module 55 Ethernet Modules (PACSystems™) 49 Genius Bus Controllers 53 Modules to a Carrier/Base 61 Adding Targets 24 Address and Length (LD) Configuring 68 Address Use Report 40 Advanced Math Functions IL 84 LD 75 Aliases 102 Analog Start Address 79 Arrays 16 Assigning Operands to an Instruction 80 Variables to Operands 70 B Basic CPU Redundancy 50 Basic Instructions IL 84 Bit Operations IL 84 LD 75 Bit References 18 Blocks GFK-1918D _MAIN 63 C 2, 63, 86 CAM 100, 102 IL 63 LD 63, 66 Local Logic 95 PLC Motion 92 Reports 40 Scheduling 64 BOOL Variables Changing the State 82 Forcing the State 83 Removing the Force 83 Boolean Start Address 79 Build Tab 33, 35 C C Block Report 40 C Blocks 2, 63, 86 Importing 86 Setting Parameters 87 C Programs 2, 63, 88 Setting Parameters 89 CAM Blocks 100, 102 Aliases 102 Creating 100 Importing 100 CAM Editor 2, 91, 100 CAM Profile Report 40 CAM Profiles Configuring 101 Creating 101 Editing 102 Carrier/Base 61 Adding Modules 61 Adding to VersaMax Remote I/O 60 Changing the State of BOOL Variables 82 Choosing CPUs 45 Power Supplies 45 CIMPLICITY Machine Edition 1, 2, 6, 9, 12, 32, 35 CIMPLICITY Motion 2, 12 CIMPLICITY View 2, 12 CimplicityControl 1, 12 Coils LD 75 COM 25 COM ports 28 Communication Configuring with nonPACSystems™ RX7i 30 Configuring with PACSystems™ RX7i 28 Ethernet 28 Serial Connection 28 Companion 15, 33 Companion Help Using 20 Compound Structure Variables 16 Configuring Accumulators 79 Address and Length (LD) 67, 68 CAM Profiles 101 Communication with nonPACSystems™ RX7i 30 Communication with PACSystems™ RX7i 28 CPUs 32, 46 DSM314 55, 56 CIMPLICITY Logic Developer - PLC Version 4.00 103 Index Ethernet Communication 28 Ethernet Daughterboard 48 Execution Scheduling 89 Hardware 27, 43 PACSystems™ RX7i 44 Redundant Systems 52 Remote I/O 1 Scheduling 64 Secondary HWC 54 Serial Communication 28 Targets 25 VersaMax Remote I/O 59 Contacts LD 75 Context-Sensitive Help 15, 20 Control Functions IL 84 LD 76 Conversion Functions IL 84 LD 76 Conversion Reports 27 Converting Targets 26 Copying Entire LD Blocks as text 71 Sections of LD Blocks as text 71 Text into the LD Editor 71 Counters IL 84 LD 76 CPE010 45 CPU Choosing 45 Configuring 32, 46 CPU Redundancy Setting Up Primary HWC 52 CPU Redundancy Over Genius 50, 51 CPU364 31 CPU374 31 Creating CAM Blocks 100 CAM Profiles 101 IL Blocks 79 104 Local Logic Blocks 95 Projects 12, 43 Reports 40 User-Defined Folders 64 User-Defined RVTs 39 Variables 17 Variables from Names 81 Variables from Reference Addresses 81 CTL Bits (Local Logic) 95 Customizing the LD Editor 66 D Data Move Functions IL 85 LD 76 Data Table Functions IL 85 LD 77 Data Values Monitoring 82 Data Watch Tool 14 Default RVTs 38 Diagnostics 37 Documentation Address 25 Downloading IP Addresses non-PACSystems™ 32 PACSystems™ RX7i 29, 30 Downloading to a Target 35 DSM314 55, 56, 91, 92, 95 Adding 55 Configuring 55, 56 Dual HWC 25, 53, 54 Duplicating IL Logic 81 E Editing CAM Blocks 101 CAM Profiles 102 IL Blocks 79 LD Blocks 67, 70 LD Logic 70 Local Logic Blocks 95 PLC Motion Blocks 92 CIMPLICITY Logic Developer - PLC Version 4.00 Projects 12 Variables 16 Editing Online 72 Editors CAM 2, 91, 100 IL 2, 79 LD 2, 66 Local Logic 2, 91, 96 Logic 63 PLC Motion 2, 91, 92 Ethernet 25, 28, 44, 48, 49 Adding Modules 49 Ethernet Adapter 28 Ethernet Daughterboard 44 Configuring 48 Executing Programs 37 Execution Scheduling Configuring 89 Expansion Racks 43, 44, 47 F Fan Kits Adding to PACSystems™ RX7i 48 Catalog 48 Intelligent 43 Non-Intelligent 43 Fault Locating References 27 Fault Table Reports 37 Fault Tables 37 Feedback Zone 14, 33, 35, 40, 41 Finding text Global Search 65 In one block 65 Folders Importing 13 Forcing BOOL Variables 74, 83 Functions IL 84 LD 75 fxClasses 15 G GBC 54, 57 GFK-1918D Index Adding 53 GE Fanuc PLC 1, 2, 24 Remote I/O 24 Series 90™-70 Genius Remote I/O Scanner 23 VersaMax Ethernet 23 VersaMax Genius 23 VersaMax Profibus 23 Genius Bus Controller (GBC) 54, 57 Adding 53 Genius Devices 44 Genius Redundancy 50, 51 Global Search 65 Going Offline from a Target 34 Going Online to a Target 34, 72 H Hardware Configuring 27, 43 Hardware Configuration (HWC) 2, 26, 43 Hardware Configuration Report 40 Help Companion 20 InfoViewer 20 Help Index 21 HWC 26, 43 Dual 54 Primary 50, 55 Secondary 50, 54, 55 Synchronizing 55 Hyperlinks 41 I IL Block Comments Inserting 81 IL BlockReport 40 IL Blocks 63 Creating 79 Editing 79 IL Code GFK-1918D Reformatting 81 IL Editor 2, 79 Offline 80 Online 82 IL Functions 84 Advanced Math 84 Basic Instructions 84 Bit Operations 84 Control 84 Conversion 84 Counters 84 Data Move 85 Data Table 85 Math 85 Program Flow 85 Relational 85 Timers 85 IL Inline Comments Inserting 81 IL Instructions 84 Inserting 80 IL Logic 2, 79 Duplicating 81 Moving 81 Importing C Blocks 86 CAM Blocks 100 Folders 13 Index 21 InfoViewer 15, 40 InfoViewer Help 20 Inserting IL Block Comments 81 IL Inline Comments 81 IL Instructions 80 LD Instructions 68 Inspector 14 Installation 4 Instruction List (IL) 79 Instructions IL 84 LD 75 Interacting with the PLC 33 Internet Explorer 15 IP Address 25, 32 Downloading to nonPACSystems™ 32 Downloading to PACSystems™ RX7i 29, 30 Setting for Lower-End Series 90™-30 32 Setting for PACSystems™ RX7i (Permanent) 30 Setting for PACSystems™ RX7i (Temporary) 29 Setting for Series 90™-30 CPU364 31 Setting for Series 90™-30 CPU374 31 Setting for Series 90™-70 30 L Ladder Diagram Logic 2 LD Blocks 63, 66 Copying Entire as Text 71 Copying Sections as Text 71 Editing 67, 70 Printing 41 Reports 40 LD Editor 2, 66, 70 Copying Text into 71 Customizing 66 Offline 67 Online 72 LD Functions 75 Advanced Math 75 Bit Operations 75 Coils 75 Contacts 75 Control 76 Conversion 76 Counters 76 Data Move 76 Data Table 77 Math 77 Program Flow 78 Relational 78 Timers 78 LD Instructions 75 CIMPLICITY Logic Developer - PLC Version 4.00 105 Index Inserting 68 LD Logic 2, 66, 70 LLVT 97 Local Logic 2, 91, 95 Local Logic Block Report 40 Local Logic Blocks Creating 95 Editing 95 Local Logic Editor 2, 91, 96 Logic IL 2, 79 LD 2, 66, 70 Local 2, 91 Logic Developer - PC 2, 12 Logic Developer - PLC 1, 2, 5, 6, 12, 23, 25, 33, 36, 43, 55, 63 Logic Developer - State 2, 12, 36 Logic Editors 63 Logic Printouts 40 Logicmaster 1, 12 M Machine Edition 1, 2, 9, 12, 32, 35 Starting 10 Making Word-for-Word Changes 73 Mapping Variables 17 Math Functions IL 85 LD 77 Mnemonics 80 Modem 25 Module Catalog 30, 46, 47, 49, 60, 61 Monitoring Data Values 82 Motion 2, 12 Motion Programming 91 Motion Report 40 Moving IL Logic 81 N Navigator 14, 16, 34, 38 Network Administrator 31 Network Interface Unit (NIU) 59 106 NIU 59 O Offline 33 Going Offline from a Target 34 IL Editor 80 LD Editor 67 Offline PLC Operations Disabled 34 Enabled 33 Online 33 Going Online to a Target 34 IL Editor 82 LD Editor 72 Target PLC 72 Online Editing 72 Online Force Report 40 Opening a Project 13 Operands Assigning to an Instruction 80 Assigning Variables 70 Options Tab 34, 38 P PACSystems™ RX7i 16, 23, 26, 28, 43, 66, 72, 73, 75 Adding Fan Kits 48 Configuring 44 Downloading IP Addresses 29, 30 Setting Permanent IP Addresses 30 Setting Temporary IP Addresses 29 Parameter Data (Local Logic) 95 Parameter Editor 31, 46, 56 Parameters C Blocks 87 C Programs 89 Permanent IP Address Setting for PACSystems™ RX7i 30 CIMPLICITY Logic Developer - PLC Version 4.00 PLC 1, 24 Family 25, 43 Interacting with 33 Motion Blocks 92 Motion Editor 2, 91, 92 Offline Operations 33, 34 Starting 37 Status 25 Stopping 37 Power Supply 59 Choosing 45 Primary HWC 50, 55 Setting Up for CPU Redundancy 52 Printing LD Blocks 41 Reports 41 Product Authorization 5 Program Flow Functions IL 85 LD 78 Programs C Programs 2, 63, 88 User Programs 88, 89 Projects CIMPLICITY Machine Edition 9 Creating 12, 43 Downloading 35 Editing 12 Executing 37, 82, 99 Importing Folders 13 Opening 13 Uploading 35 PSA100 45 Q Quick Start 10 R Racks 43, 59 Expansion 43, 44, 47 Replacing 47 Secondary 44, 47 GFK-1918D Index Redisplaying Reports 41 Redundancy 50 Basic CPU 50 Configuring Systems 52 CPU Over Genius 50, 51 Genius 50, 51 Wizards 52, 53 Reference Address 16, 39, 68 Reference View Tables Default 38 User-Defined 38 Working with 40 Reference View Tables (RVT) 38 Reformatting IL Code 81 Relational Functions IL 85 LD 78 Remote I/O 2, 24, 43, 60 Configuring 1 Remote I/O Scanner 57 Setting Up 58 Removing the Force from BOOL Variables 83 Replacing Racks 47 Text 65 Reports 40 Address Use 40 C Block 40 CAM Profile 40 Conversion 27 Creating 40 Fault Table 37 Hardware Configuration 40 IL Block 40 LD Blocks 40 Local Logic Block 40 Motion 40 Online Force 40 Printing 41 Redisplaying 41 Variables 40 Reports Tab 40, 41 Right-Click Menu HWC 45 GFK-1918D Target 33, 91 RMS 72 Run Mode 36 Run Mode Store (RMS) 72 Runtime Destination 23 Runtime Files 35 RVT 38 S SBA Node 57 Scheduling Blocks 64 Configuring 64 User Programs 89 Searching Global Search 65 In one block 65 Secondary HWC 50, 55 Configuring 54 Secondary Racks 44, 47 Serial Communication 28 Series 90™ Micro 23, 73 Series 90™-30 23, 44, 55, 66, 73 Series 90™-70 23, 26, 43, 44, 50, 66, 73, 75, 88 Remote I/O Scanner 23 Series 90™-70 Genius Remote I/O Scanner 23, 57 Setting Access Control 65 Setting IP Addresses Lower-End Series 90™-30 32 PACSystems™ RX7i (Permanent) 29 PACSystems™ RX7i (Temporary) 29 Series 90™-30 CPU364 31 Series 90™-30 CPU374 31 Series 90™-70 30 Setting Parameters C Blocks 87 C Programs 89 Setting Up Primary HWC for CPU Redundancy 52 Remote I/O Scanner 58 Slots 44, 45 SNP_ID 28 Starting a PLC 37 Starting Machine Edition 10 Status Bar 34 Stop Mode 36 Stopping a PLC 37 Sweep Time 25 Symbolic Variables 16, 17 Synchronizing HWCs 55 System Requirements 3 T Table of Contents 22 Target Properties 25 Targets 23, 63 Adding 24 Configuring 25 Converting 26 Downloading 35 Going Offline 34 Going Online 34, 72 Offline 33 Online 33 PACSystems™ RX7i 23 Remote I/O Scanner 57 Right-Click Menu 33, 91 Run Mode 36 Series 90™ Micro 23 Series 90™-30 23 Series 90™-70 23 Series 90™-70 Remote I/O Scanner 23 Stop Mode 36 Uploading 36 Validating 33 VersaMax 23 VersaMax Ethernet 23 VersaMax Genius 23 VersaMax Nano/ Micro 23 VersaMax Profibus 23 Writing Changes 74, 83 Technical Support 7 Templates 12, 24, 59 CIMPLICITY Logic Developer - PLC Version 4.00 107 Index Temporary IP Address Setting for PACSystems™ RX7i 29 Timers IL 85 LD 78 Toolchest 15 Tools 14 U Uploading from a Target 36 URL 25 User Programs 88, 89 Scheduling 89 User-Defined Folders Creating 64 User-Defined RVTs 38 Creating 39 Using 21, 22 Using Help Companion Help 20 108 Help Index 21 InfoVeiwer Help 20 Table of Contents 22 Using Templates to Create Projects 12 V Validating Targets 33 Variables 16, 27 Compound Structure 16 Creating 17 Creating from Names 81 Creating from Reference Addresses 81 Editing 16 Forcing 74 Mapping 17 Symbolic 16, 17 Turning On or Off 74 Variables Report 40 VersaMax 23, 66, 73 CIMPLICITY Logic Developer - PLC Version 4.00 Adding Carrier/Base to Remote I/O 60 Configuring Remote I/O 59 Ethernet 23 Genius 23 Nano/ Micro 23, 73 Profibus 23 Remote I/O 59 VersaPro 1, 12 View 2, 12 Viewing Fault Table Reports 37 W Windows Explorer 14 Word-for-Word Changes 34, 72 Making 73 Working with Reference View Tables 40 Writing Changes to a Target 74 Writing Changes to a Target PLC 83 GFK-1918D
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Modify Date : 2003:07:10 16:52:22-04:00 Create Date : 2003:05:20 13:52:26Z Creator : FrameMaker 6.0 Subject : GFK-1918D Page Count : 114 Creation Date : 2003:05:20 13:52:26Z Mod Date : 2003:05:20 14:18:59Z Producer : Acrobat Distiller 5.0 (Windows) Metadata Date : 2003:05:20 14:18:59Z Title : fXVersaPro.book Page Mode : UseOutlinesEXIF Metadata provided by EXIF.tools