GE GFWR2700H1WW User Manual WASHER Manuals And Guides 1508274L
User Manual: GE GFWR2700H1WW GFWR2700H1WW GE WASHER - Manuals and Guides View the owners manual for your GE WASHER #GFWR2700H1WW. Home:Laundry & Garment Care Parts:GE Parts:GE WASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
-.,h. C_4 .. O( Y t,, Appliances Procedure for Programming Controls: WH12X23219 and WH12X23218 When replacing the User Interface control has been programmed. (UI) control, the washer will not function properly until the replacement Once the UI has been replaced, it may sometimes power up with all of the UI LEDs blinking. case, follow only steps 6-9 below. Otherwise, follow all of the steps from the beginning. If this is the Step 1 Begin with the washer in Idle Mode (all LEDs on display off). Step 2 Depending on model, press the following key sequence, to enter Service Mode: [] GHWS3600F, GHWS3605F, GFWR4800F and GFWR4805F Rinse--> Delay Wash --> Rinse--> Delay Wash [] GFWS2600F, GFWS2605F, GFWR2700H and GFWR2705H Extra Rinse--> Delay Wash--> Extra Rinse--> Delay Wash Note: The sequence must be done in order. If there are any other button presses or buttons are pressed out of order, the sequence must be started from the beginning. Step 3 Upon entering the Service Mode, the UI will be in Test Selection Mode and will show "O1" (Test Number 1). Step 4 Rotate the knob clockwise until the display shows "O2". Step 5 Once "02" is showing on the 7-segment display, press the Start/Pause The digits on the 7-segment display will begin blinking. button to initiate the Model Number test. Step 6 Simultaneously the model. press and hold both the Tamp & Spin buttons for three seconds to prepare the control for selecting Step 7 Press the Soil button to increase or press the Tamp button to decrease the Model Code number selection until correct number is displayed, per the table below. Washer Model Number Catalog # Model Code GFWS2600F / GFWS2605F (all models) WH12X23219 001 GFWR2700H / GFWR2705H (ell models) WH12X23218 005 GHWS3600F / GHWS3605F (all models) WH12X23219 002 GFWR4800F0 or F1 / GFWR4805F0 or F1 (F0 or F1 models) WH12X23219 003 GFWR4800F2 / GFWR4805F2 (F2 or greeter models) WH12X23219 006 Step 8 Once the Model Code is selected, press and hold the Start/Pause button for three seconds to set the model. The board will then return to an idle state and will exit the Service Mode. It could take up to 10 seconds for the washer to respond after setting the model. Step 9 The washer is now ready for use. Note: If the above sequence is interrupted at any time, the Ul Model Code will not be saved properly. If an error is made in selecting the correct model number, repeat the steps. GE Appliances & Lighting General Electric Company Louisville, KY40225 GEAppNances.com WHOOX5625 31-16721-2 05-15 GE -.,h. C_4 .. O( Y t,, Appliances Procedure for Programming Controls: WH12X23219 and WH12X23218 When replacing the User Interface control has been programmed. (UI) control, the washer will not function properly until the replacement Once the UI has been replaced, it may sometimes power up with all of the UI LEDs blinking. case, follow only steps 6-9 below. Otherwise, follow all of the steps from the beginning. If this is the Step 1 Begin with the washer in Idle Mode (all LEDs on display off). Step 2 Depending on model, press the following key sequence, to enter Service Mode: [] GHWS3600F, GHWS3605F, GFWR4800F and GFWR4805F Rinse--> Delay Wash --> Rinse--> Delay Wash [] GFWS2600F, GFWS2605F, GFWR2700H and GFWR2705H Extra Rinse--> Delay Wash--> Extra Rinse--> Delay Wash Note: The sequence must be done in order. If there are any other button presses or buttons are pressed out of order, the sequence must be started from the beginning. Step 3 Upon entering the Service Mode, the UI will be in Test Selection Mode and will show "O1" (Test Number 1). Step 4 Rotate the knob clockwise until the display shows "O2". Step 5 Once "02" is showing on the 7-segment display, press the Start/Pause The digits on the 7-segment display will begin blinking. button to initiate the Model Number test. Step 6 Simultaneously the model. press and hold both the Tamp & Spin buttons for three seconds to prepare the control for selecting Step 7 Press the Soil button to increase or press the Tamp button to decrease the Model Code number selection until correct number is displayed, per the table below. Washer Model Number Catalog # Model Code GFWS2600F / GFWS2605F (all models) WH12X23219 001 GFWR2700H / GFWR2705H (ell models) WH12X23218 005 GHWS3600F / GHWS3605F (all models) WH12X23219 002 GFWR4800F0 or F1 / GFWR4805F0 or F1 (F0 or F1 models) WH12X23219 003 GFWR4800F2 / GFWR4805F2 (F2 or greeter models) WH12X23219 006 Step 8 Once the Model Code is selected, press and hold the Start/Pause button for three seconds to set the model. The board will then return to an idle state and will exit the Service Mode. It could take up to 10 seconds for the washer to respond after setting the model. Step 9 The washer is now ready for use. Note: If the above sequence is interrupted at any time, the Ul Model Code will not be saved properly. If an error is made in selecting the correct model number, repeat the steps. GE Appliances & Lighting General Electric Company Louisville, KY40225 GEAppNances.com WHOOX5625 31-16721-2 05-15 GE
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Fri Aug 28 08:29:20 2015 Author : Title : Subject :EXIF Metadata provided by EXIF.tools