GENERALSCAN ELECTRONICS GSM500BT Bluetooth Barcode Scanner User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2461896
Application ID	zIOECqvt+bS4RbkTmi72KQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	85.31kB (1066426 bits)
Date Submitted	2014-12-03 00:00:00
Date Available	2014-12-03 00:00:00
Creation Date	2014-11-18 11:48:23
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-11-18 11:48:26
Document Title	User Manual
Document Creator	Adobe InDesign CS6 (Windows)

GS-M500BT Quick Start Guide
Thanks for you use Generalscan all series barocde scanner product!
Please be sure to read this quick start guide before you use our product in
first time.
Optimal Scanning Distance
GS-M500BT series bluetooth barcode scanner's best scanning distance is
between 5 cm to 20 cm which depend on the density of barcode .
GS-M500BT series bluetooth barcode scanner are divided into high density
and low density model. Optimal scanning distance of Low density model is 1024 cm.High density model 's scanning distance is 3-7 cm .It can read higher
density barcode like 3mil.
GS-M500BT series 2D bluetooth barcode scanner 's best scanning distance is
7cm -10 cm. Please scan barcode in this range to obtain the best performance.
Scanning Techniques
Please aim at the middle of the barcode through the red light when scan the
barcode.
Please scan properly in accordance with the following diagram,adjust the
scanner angle and distance slowly ,at the same time ,press the trigger button
,make the centre red light cover the left to right of the barcode .
Do not use the second image to scan barcode .
Charging Function
Model
Interface
Charging Voltage
Battery Volume
Charging Time
Working Time(10s interval trigger with good decode)
GS-M500BT
Micro-USB
DC-5V 0.5A
600maH
5 hour
14 hour
GS-M500BT Quick Start Guide
Working with Mobile Phone Adapter
M series bluetooth barcode can fix on the mobile phone adapter. You can stick the adapter
on the back of mobile phone's protective case with magic double side sticker.So you can
handhold the scanner with smartphone with one hand .
Please fix mobile phone adapter in th clip on the back of scanner ,The steps is shown in
the following figure:
Installation Step
Figure-1
Figure-1 ,Put the
front of scanner into
the clip of adapter
Figure-2，Press the
bottom of scanner
,make the clip of
adapter claw at the
scanner.
Figure-2
Dismantle Step
Figure-3 ，Put the
clip of adapter to
outside
图二
Figure-4,Put scanner
up from the adapter
and take out the
scanner.
Figure-3
Figure-4
GS-M500BT Quick Start Guide
Product Outlook
④
⑤
①
⑥
⑧
Function Description
Item
Name
Scanning Window
Buzzer Hole
Trigger Button
Status LED
Strap Hole
MicroUSB
Power Switch
Buckle for Adapter
Magic Strap Hole
10
Battery cover
⑦
Description
Reading barcode ,Red light or Laser will beam out from this
window
The buzzer will sound when good decoded：
（1）Connect USB cable，buzzer will beep “b....b.b.”；
（2）Good decoed：Flashing green light and buzzer one time.
Press the trigger button to scan the barcode one time,Double
click to hide and display soft keyboard in iOS device like iphone
or iPad.
LED has three color (Red,Green,Blue) which indicate with different
scenario.Please reference the following table for detail description
Fix strap into this hole
Charge with bluetooth barcode scanner with Micro-USB or
connect PC with USB port.
Swith to left or right to power on the scanner of turn off the
scanner.Please turn off the power to save power.
Use for buckle scanner with adapter
Take the yellow magic strap through the hole to wear it on the
finger
Take off the battery cover to change the battery
LED Indicator Description
Item
Status
Green LED light flashing (with buzzer sound)
Green LED light flashes continuously
Red LED light constant light
Red LED light turn off
Red LED light flashes continuously
Blue LED continuously flashing
Blue LED turn off
Description
Decode success
Low battery alarm
Charging
Charging is complete
Built-in battery abnormal
Enter the Bluetooth pairing mode
Bluetooth Pairing successful
Bluetooth Pairing Guide
Bluetooth Pairing and Data Transfer
When you use Generalscan GS-M500 series bluetooth barcode first time,the
default data transfer interface is bluetooth ,You can pairing bluetooth barcode scanner
with Android ,iOS,WP8 smartphone or Windows tablet. For detail instruction ,please
reference the following document：
http://www.generalscan.com/pdf/BluetoothPairUserGuide-english.pdf
When you connect with Android and iOS smartphone,please confirm the data
interface is Bluetooth ,If you don't confirm ,please scan the following barcode to
switch Bluetooth mode.
Set Bluetooth Output
The bluetooth have two transfer protocol ,One is HID keyboard ,You can use this
protocol as a external keyboard.Android and iOS support HID ,You don't need install
any software to use HID.You can scan barcode into the cursor position.Please scan the
following barcode to switch HID mode：
HID Mode
Another mode is SPP mode. This mode is wireless serial port mode .Android
system support SPP mode ,but iOS don't support this mode for free, When you
connect Android not successful in HID mode ,please switch to SPP mode.
SPP Mode
When you connect with Android and iOS device ,please scan the Enter Pairing
Mode barcode first .You will see the blue LED will blink after scan Enter Pairing Mode
barcode, then search device in Android and iOS setting interface,The name of GS-M
serial bluetooth barcode will display as "GS-BarcodeScanner"
Enter Pairing Mode
After you pairing successfuly ,the blue LED will stop blink.
The detail pairing procedure for Android ,iOS ,WP8 ,please reference the
following video：
http://www.generalscan.com/en-us/video-en.php
Programming Bar Code
Factory Reset
USB Accessory Sleep Disable
Sled Battery Information Upload Enable
SLed Battery Information Upload Disable
Enter Standard Charging Mode
Enter Quick Charing Mode
USB Accessory Sleep in 60 minutes
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2014:11:18 11:48:23+08:00
Metadata Date                   : 2014:11:18 11:48:26+08:00
Modify Date                     : 2014:11:18 11:48:26+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:bdc718aa-d909-41b9-bbd4-d1892d5ee2d2
Original Document ID            : xmp.did:9555F66A15D1E311B372E712EE214F8F
Document ID                     : xmp.id:FD0A37AFD56EE4119491B41870826F02
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:FC0A37AFD56EE4119491B41870826F02
Derived From Document ID        : xmp.did:780A2AE3D36EE4119491B41870826F02
Derived From Original Document ID: xmp.did:9555F66A15D1E311B372E712EE214F8F
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2014:11:18 11:48:23+08:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 6
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools