GIGA TMS UM800 UHF RFID READER / WRITER MODULE User Manual rf1356op

Download:
Mirror Download [FCC.gov]
Document ID	2328775
Application ID	ZVz1GtijDVKSxDcidAeJDQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	44.11kB (551370 bits)
Date Submitted	2014-07-18 00:00:00
Date Available	2014-07-18 00:00:00
Creation Date	2014-06-23 16:55:16
Producing Software	Microsoft® Office Visio® 2007
Document Lastmod	2014-06-23 16:55:16
Document Title	rf1356op
Document Creator	Microsoft® Office Visio® 2007
Document Author:	jerry

UM800 Series
Embedded UHF RFID
Read/Write Module
User's Manual
TM970177
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user's authority to operate this
equipment. (Example - use only shielded interface cables when connecting to computer or
peripheral devices).
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must be
labeled in visible area with the following: “Contains FCC ID: __ WXAUM800___”
”
End Product Manual Information
The user manual for end users must include the following information in a prominent location
“IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna
used for this transmitter must be installed to provide a separation distance of at least 20cm from all
persons and must not be colocated or operating in conjunction with any other antenna or
transmitter.” This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions (1) This device may not cause harmful interference and (2) This device
must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or colocation with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the
OEM integrator will be responsible for reevaluating the end product (including the transmitter) and
obtaining a separate FCC authorization. This device is intended only for OEM integrators under
the following conditions: The antenna must be installed such that 20 cm is maintained between the
antenna and users. As long as a condition above is met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end product for any additional
compliance requirements required with this module installed (for example, digital device emissions,
PC peripheral requirements, etc.).
D-
D+
TXD
RXD
PIO8
34
VRF
PIO7
33
GND
PIO6
10
32
GND
31
ANT
30
GND
PIO5
11
PIO4
12
PIO3
13
29
GND
PIO2
14
28
GND
PIO1
15
27
GND
PIO0
16
26
GND
VDD
17
25
GND
19
20
21
22
23
24
GND
GND
GND
GND
UM800
18
Access Control System
Security System
RFID Printer
Mobile Phone
Point of Sale
Patrol System
Portable Battery Device
APPLICATIONS
·
Top View
·
·
·
·
PIN DIAGRAMS
V33
·
·
C2CK
·
·
Low cost ,Small Outline 30x20x3.6mm
Compliant with EPCglobal Class1 Gen2
(ISO18000-6C)
Operating Frequency 840 ~ 960 MHz
Adjustable Transmit Output Power from +10
to +22dBm
Operate voltage range 5 V
Low power consumption: 50mA@ standby,
250mA @22dBm Output
USB HID or UART TTL Interface
12 GPIO for Customize Application
No RF Connect and Cable request
Support In-System Programmable and Self
Firmware Update
Provides Development Kit - UM800DK
PIO9
·
·
PIN #1
IDENTIFY
PIO10
FEATURES
Embedded UHF RFID Read/Write Module
C2D
PROMAG
UM800
PIO11
GIGA-TMS
34-PIN SMD
DESCRIPTION
UM800 is a compact and practical embedded UHF reader module which compliant with EPC Global
Class1 Gen2.
With small dimensions (30x20x3.6mm) and low power consumption ( 50mA for standby;250mA,
22dBm for output) make UM800 an ECO friendly choice for your system.
With adjustable frequency (840~960 Mhz), adjustable transmit output (10 to 22dBm), optional
interface (USB or UART TTL) and 12 GPIO enable you the flexibility for various applications under
different environments.
UHF is one of the best solutions for middle and long range RFID applications.
Such as access control, parking, logistic and vehicle tracking etc.
Using UM800, you can extend the wonderful experience to portable or mobile devices.
GIGA-TMS makes what you need and customizes what you want.
Copyright 2012 by GIGA-TMS Corporation.
HTTP://WWW.GIGATMS.COM.TW
Preliminary
UM800
PIN FUNCTIONS
Pin1
GIGATEK
made in Taiwan
MODEL NO.:UM800
PART NO.:UM800-00
FCC ID : WXAUM800
MFG. NO.:REV.X
XXXX XXX XXXX
Top View
PIN
PIN
NAME
I/O
10
11
12
13
14
15
16
17
18
19
20
21~30
31
32~33
34
RXD
TXD
D+
DV33
C2CK
C2D
PIO8
PIO7
PIO6
PIO5
PIO4
PIO3
PIO2
PIO1
PIO0
VDD
PIO11
PIO10
PIO9
GND
ANT
GND
VRF
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Bottom View
FUNCTION DESCRIPTION
USART asynchronous input.
USART asynchronous transmit.
USB Differential Plus Line
USB Differential Minus Line
3.3V Voltage Output, Maximal 100mA Current Output
ISP
ISP
GPIO , 5 V tolerant with high sink current
GPIO , 5 V tolerant with high sink current
GPIO , 5 V tolerant with high sink current / Wiegand Data0
GPIO , 5 V tolerant with high sink current / Wiegand Data1
GPIO , 5 V tolerant with high sink current
GPIO , 5 V tolerant with high sink current
GPIO , 5 V tolerant with high sink current
GPIO , 5 V tolerant with high sink current
GPIO , 5 V tolerant with high sink current
5 V Power Supply ( 5.3V is suggested )
GPIO , 5 V tolerant with high sink current
GPIO , 5 V tolerant with high sink current
GPIO , 5 V tolerant with high sink current
Power Ground
Connect To Antenna
Power Ground
RF PA power supply Input ( UM800 not use )
[ Note 1 ] I : Input , O : Output , I/O : Input or Output , P : Power , A : Antenna
Copyright 2012 by GIGA-TMS Corporation.
HTTP://WWW.GIGATMS.COM.TW
Preliminary
UM800
APPLICATION CIRCUIT
GND
RXD
Vin
*Note3
TXD
UART TTL
GND
D+
D-
Vbus
USB
GND
C2CK
C2D
3V3
ISP
*Note1,2
VCC
VDD
RXD 1
D+ 3
TXD 2
D- 4
V33 5
C2D 7
C2CK 6
+3.3V
Output
8 PIO8
VRF 34
9 PIO7
GND 33
10 PIO6
GND 32
11 PIO5
ANT 31
12 PIO4
GND 29
14 PIO2
GND 28
PIO11
PIO10
PIO9
GND
GND
GND
GND
23
24
GND 25
22
17 VDD
Lp
21
GND 26
20
GND 27
19
15 PIO1
16 PIO0
18
VDD
50 ohm RF track
GND 30
UM800
13 PIO3
*Note1,2
Antenna
[ Note ]
1. When UART Interface : VCC > 5.5V
VCC
LowDropout
Regulator
VDD
or
VCC
StepDown
DC/DC
LowDropout
Regulator
VDD
2. When UART Interface : VCC < 4.75V
VCC
Step-up
DC/DC
LowDropout
Regulator
VDD
3. When USB Interface :
VDD
D+
D-
Vbus
D+
DESD
PROTECTOR
Copyright 2012 by GIGA-TMS Corporation.
HTTP://WWW.GIGATMS.COM.TW
Preliminary
UM800
SPECIFICATIONS
POWER REQUIREMENTS
4.75 ~ 5.5V ( 5.3V is recommended.) regulated for Operate Voltage . A linear
regulator is recommended.
CURRENT CONSUMPTION
50 mA AVG @ Standby Mode
250 mA AVG @ 22dBm RF Power Output
RFID PROTOCOL SUPPORT
SUPPORT EPC DRM
FREQUENCY
DEMODULATION
DATA ENCODING
BIT RATE
TX OUTPUT POWER
ANTENNA TYPE
EPC Class 1 Gen 2, ISO18000-6C
Yes
840 ~ 960MHz
ASK or PSK
FM0 or Miller code
Supports uplink data rate of 40,160,320 Kbps
10 ~ 22 dBm
Mono-static
HOST INTERFACE
UART ( Default : 19200 Baud rate ) Programmable
USB HID
INPUT / OUTPUT PIN
Programmable 12 Input / Output Pin by Customer
CONFIGURE INTERFACE
DIMENSIONS
WEIGHT
UART , 19200 bps 8N1
30 x 20 x 3.6 mm
< 10 gm
ENVIRONMENT
Operating Temp : -0℃ ~ +60℃
Humidity : 10 ~ 90 % Non-condensing
PACKAGE DESCRIPTION
34-Pin SMD Package
Dimensions in Millimeters
2.54
T=0.8
25
PIN1
Top View
20
18
30
Copyright 2012 by GIGA-TMS Corporation.
HTTP://WWW.GIGATMS.COM.TW
3.2
Preliminary
UM800
Package Drawings and Markings
11
3.82
0.3
5.25
GIGATEK
4.85
6.04
3.25
2.54
made in Taiwan
30 mm
MODEL NO.:UM800
PART NO.:UM800-00
FCC ID : WXAUM800
MFG. NO.:REV.X
XXXX XXX XXXX
3.95
2.25 0.3
4.42
0.3 2.34
3.09
0.83
Pin 1
Pin 1
1.35
20 mm
2.06
1.8
3.6V
3.3V
Example Board Layout
UM800
GND
TOP SOLDER
TOP LAYER
Copyright 2012 by GIGA-TMS Corporation.
HTTP://WWW.GIGATMS.COM.TW
TOP OVERLAY
Preliminary


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 8
Language                        : zh-TW
Tagged PDF                      : Yes
Title                           : rf1356op
Author                          : jerry
Subject                         : 
Create Date                     : 2014:06:23 16:55:16+08:00
Modify Date                     : 2014:06:23 16:55:16+08:00
Producer                        : Microsoft® Office Visio® 2007
Creator                         : Microsoft® Office Visio® 2007

EXIF Metadata provided by EXIF.tools