GL Solutions TM10-B-QQ RFID READER/WRITER MODULE User Manual
GL Solutions Inc. RFID READER/WRITER MODULE Users Manual
Manual r1
1/4
User’s Manual
FCC ID: VQ7TM10-B-QQ
IC ID: 10795A-TM10BQQ
Model No.:TM10-B/QQ
Manufacturer’s name: GL Sciences Inc.
Precautions of use
Before using the reader/writer and card, read the following precautions. Be sure to
adhere to the precautions to avoid malfunctions and failures caused by misuse. Note
that we shall bear no responsibilities for collateral damages to the stored data caused by
faults, malfunctions or failures of the reader/writer.
Changes or modifications not expressly approved by the manufacturer for compliance
could void the user’s authority to operate the equipment.
1. Installation in an enclosure
Adhere to the following mounting dimensions when installing the board in an enclosure.
Only the diagonally shaded area around the mounting hole may be metal.
6.0
6.0
R3
2/4
2. Care should be taken when modifying the card attributes and key settings
When modifying the card attributes and key settings, the card must be in the
reader/writer’s communication range. If the special data area is compromised due to
insufficient power supply, access to the card will become infeasible thereafter.
3. Avoid using the reader/writer in the presence of strong electromagnetic
waves
The reader/writer supplies power to the card via an electromagnetic wave to
communicate with the card. Presence of strong electromagnetic waves (especially waves
with frequencies around 13.56 MHz) in the proximity of the reader/writer or card will
affect communication between the reader/writer and card, causing reduced access area
or inability to access the card. Similarly, if the switching frequencies (and its harmonics)
of a switching mode power supply, or its backup switch-mode UPS/CVCF are around
13.56 MHz, switching noises will affect the reader/writer via wiring; be sure to test the
reader/writer using the actual power source in the installation location environment
before use.
4. Keep precision devices that may be affected by electromagnetic waves
away from the reader/writer
Since the reader/writer constantly emits an electromagnetic wave (of around 13.56
MHz), placing precision devices that may be affected by electromagnetic waves near the
reader/writer can cause malfunction or failure of the devices. When operating the
reader/writer, keep precision devices away from the reader/writer. If such precision
devices must be located near the reader/writer, shield the precision devices with a metal
cover and be sure to test the devices to check for any influence.
5. Avoid using multiple readers in proximity to each other
The reader supplies power to the card via an electromagnetic wave to communicate with
3/4
the card and thus constantly emits an electromagnetic wave (of around 13.56 MHz).
Using multiple readers in proximity to each other will cause interference, interrupt
communication between the card and reader, and prevent access to the card.
The readers must be apart from each other by at least 30 cm in every direction.
Others
- Use the reader/writer as a general-purpose communication tool (for terminals) such
as OA devices.
- Use the reader/writer in a place unaffected by organic solvents, oils or water.
- Use the reader/writer in a place free of corrosive gases, toxic gases, or flammable
gases.
FCC/IC Statements
This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The following sentence has to be displayed on the outside of the device in which the
transmitter module is installed:
“Contains FCC ID: VQ7TM10-B-QQ”
“Contains transmitter module IC: 10795A-TM10BQQ”
RF exposure information: This equipment complies with FCC/IC radiation exposure
limits set forth for an uncontrolled environment.
CAUTION: Any changes or modifications not expressly approved by the party
responsible for compliance could void the users’ authority to operate this equipment.
IC Statement (French)
Cet appareil est conforme à la norme CNR210 des règlements d’Industrie Canada. Son
fonctionnement est sujet aux deux conditions suivantes: 1) Cet appareil ne doit pas
provoquer d’interférences et 2) Cet appareil doit accepter toutes les interférences, y
compris celles pouvant entraîner son dysfonctionnement.
4/4
La phrase suivante doit être affichée à l'extérieur du dispositif, dans lequel le module
émetteur est installé:
“Contains transmitter module IC: 10795ATM10BQQ”
Avis d’Industrie Canada sur l’exposition aux Rayonnements: Cet appareil est conforme
aux limites d’exposition aux rayonnements d’Industrie Canada pour un environnement
non contrôlé.
CE Statements
GL Science Inc. declares that this product is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
The mentioned device has been successfully tested against the following standards;
EN 302 291-2 V1.1.1 (2005-07)
EN 301 489-1 V1.9.2 (2011-09)
EN 301 489-3 V1.4.1 (2002-08)
EN 60950-1:2006 + A1:2010 + A12:2011