GL Solutions TM10-B-QQ RFID READER/WRITER MODULE User Manual
GL Solutions Inc. RFID READER/WRITER MODULE Users Manual
Manual r1
User’s Manual FCC ID: VQ7TM10-B-QQ IC ID: 10795A-TM10BQQ Model No.:TM10-B/QQ Manufacturer’s name: GL Sciences Inc. Precautions of use Before using the reader/writer and card, read the following precautions. Be sure to adhere to the precautions to avoid malfunctions and failures caused by misuse. Note that we shall bear no responsibilities for collateral damages to the stored data caused by faults, malfunctions or failures of the reader/writer. Changes or modifications not expressly approved by the manufacturer for compliance could void the user’s authority to operate the equipment. 1. Installation in an enclosure Adhere to the following mounting dimensions when installing the board in an enclosure. Only the diagonally shaded area around the mounting hole may be metal. R3 6.0 6.0 1/4 2. Care should be taken when modifying the card attributes and key settings When modifying the card attributes and key settings, the card must be in the reader/writer’s communication range. If the special data area is compromised due to insufficient power supply, access to the card will become infeasible thereafter. 3. Avoid using the reader/writer in the presence of strong electromagnetic waves The reader/writer supplies power to the card via an electromagnetic wave to communicate with the card. Presence of strong electromagnetic waves (especially waves with frequencies around 13.56 MHz) in the proximity of the reader/writer or card will affect communication between the reader/writer and card, causing reduced access area or inability to access the card. Similarly, if the switching frequencies (and its harmonics) of a switching mode power supply, or its backup switch-mode UPS/CVCF are around 13.56 MHz, switching noises will affect the reader/writer via wiring; be sure to test the reader/writer using the actual power source in the installation location environment before use. 4. Keep precision devices that may be affected by electromagnetic waves away from the reader/writer Since the reader/writer constantly emits an electromagnetic wave (of around 13.56 MHz), placing precision devices that may be affected by electromagnetic waves near the reader/writer can cause malfunction or failure of the devices. When operating the reader/writer, keep precision devices away from the reader/writer. If such precision devices must be located near the reader/writer, shield the precision devices with a metal cover and be sure to test the devices to check for any influence. 5. Avoid using multiple readers in proximity to each other The reader supplies power to the card via an electromagnetic wave to communicate with 2/4 the card and thus constantly emits an electromagnetic wave (of around 13.56 MHz). Using multiple readers in proximity to each other will cause interference, interrupt communication between the card and reader, and prevent access to the card. The readers must be apart from each other by at least 30 cm in every direction. Others Use the reader/writer as a general-purpose communication tool (for terminals) such as OA devices. Use the reader/writer in a place unaffected by organic solvents, oils or water. Use the reader/writer in a place free of corrosive gases, toxic gases, or flammable gases. FCC/IC Statements This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The following sentence has to be displayed on the outside of the device in which the transmitter module is installed: “Contains FCC ID: VQ7TM10-B-QQ” “Contains transmitter module IC: 10795A-TM10BQQ” RF exposure information: This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the users’ authority to operate this equipment. IC Statement (French) Cet appareil est conforme à la norme CNR210 des règlements d’Industrie Canada. Son fonctionnement est sujet aux deux conditions suivantes: 1) Cet appareil ne doit pas provoquer d’interférences et 2) Cet appareil doit accepter toutes les interférences, y compris celles pouvant entraîner son dysfonctionnement. 3/4 La phrase suivante doit être affichée à l'extérieur du dispositif, dans lequel le module émetteur est installé: “Contains transmitter module IC: 10795ATM10BQQ” Avis d’Industrie Canada sur l’exposition aux Rayonnements: Cet appareil est conforme aux limites d’exposition aux rayonnements d’Industrie Canada pour un environnement non contrôlé. CE Statements GL Science Inc. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The mentioned device has been successfully tested against the following standards; EN 302 291-2 V1.1.1 (2005-07) EN 301 489-1 V1.9.2 (2011-09) EN 301 489-3 V1.4.1 (2002-08) EN 60950-1:2006 + A1:2010 + A12:2011 4/4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c320 44.284297, Sun Apr 15 2007 17:19:00 Producer : Acrobat Elements 8.0.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2013:03:04 11:45:40+09:00 Create Date : 2013:03:04 11:45:40+09:00 Format : application/pdf Title : <4D6963726F736F667420576F7264202D208274829382858292816582938140826C8281828E82958281828C5F31335F30335F30342E646F63> Creator : izaki Document ID : uuid:84875b16-d057-4072-88c0-52e21c266ec6 Instance ID : uuid:efb155c0-cc92-451e-b660-c36729ded078 Page Count : 4 Author : izakiEXIF Metadata provided by EXIF.tools