GN Audio USA GN9120 Cordless Phone User Manual users manual

GN Netcom Inc Cordless Phone users manual

users manual

GN 9120 User GuideGN NetcomGN9120 BETA User Guide 11/20/02 5:12 PM Page 1
GN 9120 User GuideComponents1. Base Unita) On-Line Indicatorb) Mute Indicatorc) Battery Re-Charge Indicatord) Link Indicatore) Telephone Termination Switch 2. Headset a) Multifunction Buttonb) Volume Up c) Volume Down3. Headband4. Earhook5. Earplate6. Ear cushion7. Base Stand8. Connection Cord 9. Cord Manager10. Power Cord3(1a)(1)(1d)(1b)(2)(3)(1e)(5)(2b)(4)(8)(9) (6)(7.)(10)(2c)(2a)(1c)GN9120 BETA User Guide 11/20/02 5:12 PM Page 2
4) Insert the Base Unit into the Base Standand twist until secure.Note: Use the Cord Manager to organize all cords attached to the Base Unit.Charging the Battery Fully charge the headset for 1.5 hours prior to initial use. To charge, place the headset in thebase. The Battery-Charging Indicator on the Base Unit will flash while charging and will stopflashing, but remain lit when the battery is fullycharged. A completely charged battery provides up to 8hours of talk time. If the battery needs to berecharged, a beep will sound in the headset every20 seconds.*** REMEMBER ***CHARGE THE BATTERY FOR 1.5 HOURS PRIOR TO INITIAL USE54Your headset will have one of the following Boom styles: a) Headset with NC (noise canceling microphone)b) Headset with SoundTubeTMc) Headset with MidiBoomTMThese instructions apply to all 3 Headsets. Installation1) Disconnect the handset cord from the telephone's handset port and connect it to the port marked handset on the Base Unit.2) Insert the Connection Cordinto the telephone's handset port marked handset. Then insert the other end of the Connection Cord into the port on the Base Unit marked telephone.3) Plug the Power Adapter into the port marked power icon at the bottom of the Base Unit. Connect to a power outlet.(a.)(b.)(c.)GN9120 BETA User Guide 11/20/02 5:12 PM Page 4
Checking Your SystemTo check that your system is set up cor-rectly, first remove the headset from theBase Unit. The green, Link Indicator onthe front of the Base Unit will light up andthe red, On-Line Indicator on the headsetwill flash. Adjusting to Your Telephone1) First, make sure the Mute function is off. If the Mute function is activated, you will hear a beep in your headset every 15 seconds. Turn off the Mute function by pressing the Multifunction Buttononce quickly.2) Put on the headset.3) Lift the telephone's handset and listen for a dial tone in your headset. 4) If there is little or no dial tone, move the Telephone Termination Switch on the back of the Base Unit, from A through G until the dial tone is clearly heard. 76Adjusting Transmit and Receive Volume 1) Put on the headset.2) Lift the handset.3) Call someone and ask them to help you evaluate the headset's transmit volume.4) Make sure that the boom arm/microphone is positioned closely to your mouth.5) Press the +/- buttons on the headset simultaneously until you hear a beep. Adjust the Transmit Volume by pressing the + or - Button. + raises transmit and - lowers transmit.When the person you are speaking with finds the volume of your voice appropriate, press the +/- Buttons simultaneously for 2 seconds. This setting is now stored in the headset.6) Now, adjust the Receive Volume by pressing the + or - Button, until you reach the sound level you desire. This setting is now stored in the headset.Note: When the maximum or minimum volume is reached, you will hear a beep in your headset. GN9120 BETA User Guide 11/20/02 5:12 PM Page 6
Answering telephone calls using the GN 1000 RHL (Remote Handset Lifter):You may purchase a GN 1000 RHL as an accessory, whichlets you answer and end telephone calls while away from yourdesk. Please contact your preferred reseller or visitwww.gnnetcom.com for further information.To use the GN 1000 RHL accessory with your GN 9120 telephone: 1) Install a Remote Handset Lifter using the directions provided with that product.2) To make a call, lift the handset out of the Base Unit. The Remote Handset Lifterwill immediately lift up and you will hear a dial tone. To terminate the call, press the Multifunction Button for 2 seconds or put the headset back in its base.3) To answer a call while wearing the headset, press the Multifunction Button quickly to establish a link. To end the call, press the Multifunction Button on your headset for 6 seconds. The call will be terminated.Conference ModeUsing the Conference Mode, additional headsets may be joinedto a telephone conference via the base station. The headsetused with your Base Unit is the Master headset.1) Lift your Master headset out of the Base Unit.2) Initiate or answer a call. Adjusting Receive Tone ControlSelect the tone (Normal, Bass Lift or Treble Lift) according to personal preference:1) Press the Multifunction Button for 6 seconds. A beep will indicate when 6 seconds has passed.2) Press the volume +or - button to toggle between the 3 sound modes.When the desired sound mode is reached, press the Multifunction Button to exit the sound mode feature.Muting the MicrophoneTo mute the microphone, press the Multifunction Button on the headset once quickly. When themicrophone is muted, you will hear a beep every 15 seconds in your headset and the red MuteIndicator on the Base Unit will light. You will still hear the other party.Placing and Answering Telephone Call1) Remove the headset from the Base Unit. The Link Indicator will light. 2) Put on the headset.3) Lift the handset from the phone. Answer or place the call.4) You can now move freely away from the Base Station. If you move out of trans mission range, you will hear a beep in the headset every 10 seconds. Once back in range, the beeping will stop.To end the call, replace the handset.98GN9120 BETA User Guide 11/20/02 5:12 PM Page 8
Your headband allows you to wear your headset on yourright or left ear. Rotate the Boom Arm (x) 180 degrees forleft ear or right ear wearing. The Stay-Put TM click-stopheadband lengthens and shortens to the desired length fora custom fit over your head. Pull to lengthen. Push to shorten.Note: The Boom Arm cannot be rotated a full 360degrees.Do not force it if you cannot rotate it any further.To Attach the Earhook for Over-the-Ear Wearing:1) Gently press the Earhook Ring into the Headset Receiver. The square knob on the Earhook Ringwill match the square hole in the Headset Receiver.2) Attach the Earhook to the Earhook Ring.After attaching the Earhook, you may now adjust the headset to be worn on your right or left ear, depending on personal preference. Changing the Headset's Wearing Style:1) Remove the Ear Cushion from the Headset Receiver (headband version only).11103) During the telephone call, place an additional headset into the Master's Base Unit. 4) Listen for a beep in the master headset. You will have 15 seconds after the beep to accept the additional headset for conference. Accept the additional headset by simultane-ously pressing the +/- Buttons briefly. The additional headset can exit the conference call by pressing the Multifunction Button for 2 seconds. 5) The conference mode is terminated when:the Master headset is placed in the Base Unit or; the Master headset's Multifunction Button is pressed for 2 seconds (this will end the call) Note: Repeat steps 3-5 to add more headsets to the conference mode. Up to 4 headsets may participate in the conference mode.Comfort AdjustmentsThe GN 9120 has 2 different wearing styles:Headband or Over-the-Ear.To attach the headband:1) Align the Headset Receiver with the Headband Ring.2) Gently press the Headband Ring to the Headset Receiver until it clicks. The square knob on the Headband Ring will match the square hole in the Headset Receiver.3) Press the Ear Cushion onto the Headset Receiver until it clicks.Align Heaband Ring withHeadset ReceiverGN9120 BETA User Guide 11/20/02 5:12 PM Page 10
- Check the position of the Boom Arm and make sure that the microphone is positioned close to your mouth.- You may be out of range. Move closer to the Base Unit.Why do I hear a buzz or humming noise in my headset?- Static sometimes results when your Base Unit is placed too close to your telephone or other electronic devices. Try moving the base station further away from other devices.Operational and Safety InformationReplacing the batteryIf you need to replace the battery, you must use GN Netcom-approved batteries.No other parts can be replaced by the user.Inside the Headset Receiver is where the battery is located, press down on the plastic tab securing the battery and pull the battery out. Insert the new battery into the battery compartment.Note: Make sure that the battery is placed correctly in the headset with the + of the battery corresponding to the + indicated in the battery slot of the headset.Memory ResetWhen the battery is removed or the power adapter is unplugged (for at least a few seconds), allcustomized headset settings (clear dial tone, transmit volume, received sound volume and tonecontrol) are returned to factory-set default settings.Cleaning and Replacing Parts The Ear Cushion and Earplate may be cleaned or replaced. When cleaning, use only water and asmall amount of dishwashing liquid if needed.For the Earplate , remove the Earplate from the Headset Receiver.For the Headset's Ear Cushion, gently peel it off the Earplate2) While carefully handling the headset, gently press the Headset Receiver's speaker with your thumb and pull the Headband/EarhookRing away.Frequently Asked QuestionsWhy can't I hear a dial tone? - Check that all the cords are connected correctly.- Be sure that the AC power adapter is plugged in and has power.- Check that the On-Line Indicator is lit. If not, place the headset in the Base Unitand take it out again.- Check that the battery is fully charged. If the battery is fully charged, the Battery-Charging Indicator on the Base Unit will light up.If the green, On-Line Indicator does not light up, check the wiring connections on the Base Unit and be sure that the AC power adapter is connected. If the On-Line Indicatoron the headset does not flash continuously put the headset back in the Base Unit and remove it again.Why do I hear beeping in my headset?- A beep every 10 seconds indicates that you are out of range. Move closer to the Base Unit.- A beep every 15 seconds indicates that the Mute function is active.- A beep every 20 seconds indicates that the battery is too low and needs recharging.Why can't the caller hear me speaking? - Check that the Mute function is off. - Readjust the microphone volume. 1312GN9120 BETA User Guide 11/20/02 5:12 PM Page 12
Cautionary Notes to Computer Users When using any headset with a computer, care should be taken in dry or low humidity environmentsto protect the user from electrostatic discharge from the monitor (CRT). Computer monitors caninduce a substantial electrostatic charge when turned on or off, or when there is a power failure, andthe resulting electrostatic discharge can be passed through the headset to ground.A user in close proximity to or touching the computer may feel a common “shock” sensation, similarto touching a doorknob after walking across a carpet, causing no harm to the user. This discharge isentirely due to the computer monitor; the headset is merely the shortest path to ground.To minimize the possibility of electrostatic discharge through the headset, you can:• Use a grounded screen in front of the monitor.• Use static dissipative wrist straps.• Increase the relative humidity in the room to 60% or more.• Install static dissipative carpets or floor coverings (anti-static sprays can be helpful).• Remove the headset before turning the computer on or off.GN Netcom, Inc. headsets meet all OSHA, UL, FCC and CS standards.Safety Instructions• Never try to dismantle the product yourself. None of the internal components can be repaired by users.• Do not expose the headset to rain or other liquids.• The headset is equipped with a rechargeable NiMH battery (nickel-metal-hydride). For battery replacement, please contact your distributor or reseller.FCC Notice to UsersUpon request only, you must notify your telephone utility company (telco) of your intention to install orpermanently remove an FCC Part 68 registered device or system. Include the FCC RegistrationNumber and the Ringer Equivalence Number (REN) located on the amplifier label.The telco has the right to make changes to their network, which may affect the operation of yourequipment, provided you are given adequate advance written notice to permit correct operation.This device complies with part 15 of the FCC Rules and ICES-003 Operation is subject to the follow-15Registering a New Master HeadsetA new master headset may be registered to the product in case of loss or damage to the original headset. To register a new master headset:1) Unplug the power adapter for a couple of seconds.2) Plug the power adapter back to the power outlet.3) Secure the new master headset into the Base Unit.14GN9120 BETA User Guide 11/20/02 5:12 PM Page 14
IC Notice to UsersThe Industry Canada label identifies certified equipment. This certification means that the equipmentmeets telecommunications network protective, operational and safety requirement as prescribed inthe appropriate Terminal Equipment Technical Resource Document(s). The department does notguarantee the equipment will operate to the user’s satisfaction.Before installing this equipment, users should ensure that it is permissible to be connected to thefacilities of the local telecommunications company. The equipment must also be installed using an acceptable method ofconnection. The customer should be aware that compliance with the above conditions may not pre-vent degradation of service in some situations.Repairs to certified equipment should be coordinated by a representative designated by the supplier.Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may givethe telecommunications company cause to request the user to disconnect the equipment.Users should ensure for their own protection that the electrical ground connections of the power utili-ty, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be partic-ularly important in rural areas. Caution: Users should not attempt to make such connections them-selves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indica-tion of the maximum number of terminals allowed to be connected to a telephone interface. The ter-mination of an interface may consist of any combination of devices subject only to the requirementthat the sum of the ringer equivalence Numbers of all the devices does not exceed 5.17ing two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation.Note: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and usedin accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equip-ment does cause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:1) Reorient or relocate the receiving antenna.2) Increase the separation between the equipment and receiver.3) Connect the equipment into an outlet on a circuit different from that to which the receiveris connected.4) Consult the dealer or an experienced radio/TV technician for help.Complies with part 15 & 68, FCC RulesOperation is subject to the following two rules:1) This device may not cause harmful interference and2) This device must accept any interference received, including interference that may cause undesired operation.Industry Canada requires Indoor Use Only16GN9120 BETA User Guide 11/20/02 5:12 PM Page 16
WarrantyGN Netcom, Inc. warrants this product against all defects in material and workmanship for a period ofone year from the date of original purchase. The conditions of this warranty and our responsibilitiesunder this warranty are as follows:• The warranty is limited to the original purchaser.• The warranty is void if the serial number, date code label or product label is removed, or if theproduct has been subject to physical abuse, improper installation, modification, or repair byunauthorized third parties.• The responsibility of GN Netcom, Inc. under this warranty shall be limited to the repair orreplacement of the product at the sole discretion of GN Netcom, Inc.• Any implied warranty on GN Netcom, Inc. products is limited to one year from the date of pur-chase on all parts, including the cords and connectors. Specifically exempt from warranty arelimited-life consumable components subject to normal wear and tear, such as microphonewindscreens, ear cushions, ear tips, decorative finishes, batteries, and other accessories. GNNetcom, Inc. is not liable for any incidental or consequential damages arising from the use ormisuse of any GN Netcom, Inc. product. • A copy of your receipt or other proof of purchase is required. Without proof of purchase, yourwarranty is defined as beginning on the date of manufacture as labeled on the product.• This warranty gives you specific legal rights and you may have other rights which vary fromstate to state.Unless otherwise instructed in the User Guide, the user may not, under any circumstances, attemptany service, adjustments or repairs on this unit, whether in or out of warranty. FCC Part 68.216 man-dates that “Repair of registered terminal equipment and registered protective circuitry shall be accomplished only by the manufacturer or assembler thereof or by their authorized agent.”ContactGN Netcom, Inc. at (800) 826-4656 for authorized service locations.19To Obtain ServiceFor customer service and technical support, call GN Netcom, Inc. at 1-800-826-4656.If it becomes necessary to send a unit in for repair, it is not necessary to call for a Return MaterialAuthorization (RMA) number, as one will be assigned upon receipt of the package at the factory.Ship the product in a suitable shipping container, fully insured and with the shipping charges prepaid.Include the following with the product:• Your name, company name, address and telephone number.• A description of the problem.• A copy of the receipt or other proof of purchase (without proof of purchase, your warranty willbe defined as beginning on the date of manufacture as labeled on the product).Or, for out of warranty products:• A purchase order which authorizes repair.In warranty products are warranted for one year from the repair date or for the remainder of the origi-nal warranty period, whichever is longer. Out of warranty products will be repaired or replaced at theprevailing charge and carry a one year warranty from repair date. GN Netcom, Inc. will not assume any responsibility for any loss or damage incurred in shipping. Anyrepair work on GN Netcom, Inc. products by unauthorized third parties voids any existing GNNetcom, Inc. warranty.Ship To: GN Netcom, Inc. • 77 Northeastern Boulevard • Nashua, NH 03062 • 1-800-826-465618GN9120 BETA User Guide 11/20/02 5:12 PM Page 18
20GN9120 BETA User Guide 11/20/02 5:12 PM Page 20

Navigation menu