GRAUPNER BLWM 2.4GHz WiFi module User Manual Yokomo BL WM USER MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	3312036
Application ID	uK62hPTBC7DYXa6l80YVwA==
Document Description	15_BL-WM UserMan
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.52kB (131483 bits)
Date Submitted	2017-03-10 00:00:00
Date Available	2017-03-10 00:00:00
Creation Date	2017-03-03 15:29:06
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2017-03-07 15:06:50
Document Title	Microsoft Word - Yokomo_BL-WM_USER_MANUAL
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

Yokomo BL-WM USER MANUAL
Thanks for purchasing BL-WM. Please carefully read this instruction manual before using this unit.
1.
Introduction
This BL-WM is connected to ESC and smart device like android, i-phone, tablet pc and
program can be set with wireless system. You can also check actual racing data in real time,
and racing information up to 50mintes can be stored so that users can easily find and know
the character of the driving.
2.
Specifications
Operating voltage: 5~7.4V
WiFi protocol: IEEE 802.11/b/g/n
WiFi valid signal range: (0~10m, depending RF status)
Size: 25 x 25 x 9 mm (L x W x H)
Weight: 7g
WiFi SSID: GRAUPNER_ESC_XXXX (MAC Address 4 )
WiFi Password: 1234567890
3.
Features
1)
Wireless Programming : Easy to set ESC program such as Power Curve, Brake,
Turbo/Boost timing, etc via smart device.
2) Live
function
/Stop
Watch:
Easy
to
check
real
driving
data
such
as
RPM/Voltage/Current/Consumed battery via Live, with Stop Watch
3) Log View: This is to store driving data for max 50min, and user can store/recall then see
the driving performance.
4) Wireless Firmware Update: User can easily update ESC/ BL-WM via smart device.
5) WiFi is On and Off according to monitor operation to minimize interference to a receiver.
4.
User Guide
1) How to connect BL-WM (Connecting the BL-WM)
a) Download BL-WM Link app then install ( please refer to our homepage )
b) Like figure below, the signal of connection location for BL-WM and ESC setting
should be connected with 3 pins white band of WiFi.
Note:
If Graupner transmitter would be used, clear SUMD V2 at CH2 setting then
use.

c)
Connect the ESC to Power then switches on the ESC. Once WiFi works, the Yellow LED
on the BL-WM should flash. Then, refer to “BL-WM – Setup item”
Note: To minimize the impact of WiFi to a receiver, WiFi module should be placed far from an
antenna on a receiver.
2)
BL-WM setting (BL-WM – Setup)
< BL-WM Link application and , connected WiFi ID>
Note : GRUAPNER_ESC_XXXX is individual WiFi module ID, and it can vary depending
on products.
Choose the detected GRAUPNER_ESC WiFi.
2.1) Switch on “WiFi” setting in a smart phone.
2.2) Then, chose “GRAUPBER_ESC_(XXXX) at WiFi, then password box appears.
2.3) Initial WiFi password is 1234567890. Insert the password then check WiFi
connection.
2.4) Once it is connected, click on “BL-WM APP” in a smart phone. Once APP start screen
is pressed, it should move into a main screen.
2.5) Click
at the right bottom of the main screen, then select WiFi item. Change
WiFi name(SSID) and password as other customers can also use the provided initial
ID and password. Reset WiFi and connect to avoid any confusion.
Note: After changing name or password of BL-WM, research again WiFi then set and
proceed.
Note: In case you forget the password, please update BL-WM using grStudio then set
WiFi and proceed. After this wired update, WiFi module is initialized. Please refer to the
homepage on the detailed operation.
2.6) After all of the above procedures are executed, overall setup on BL-WM is complete.
Once a motor is operated. WiFi is automatically On and Off, except for Live Mode. Thus,
we recommend you to switch off the application in a smart phone to reduce RF
interference during driving.
5.
LED Status (LED status)
YELLOW LED is ON
: WiFi module is ON
YELLOW LED flashes : WiFi module is OFF
RED LEDflashes
: Command comes from smart phone
RED LED is ON
: BL-WM is being updated in wired condition.
RED LED flashes three time
Initialization is complete. Default ID and password are set.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note 1: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Note 2: 1.Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
2. The minimum separation generally be used is at least 20 cm.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2017:03:07 15:06:50+08:00
Create Date                     : 2017:03:03 15:29:06+08:00
Metadata Date                   : 2017:03:07 15:06:50+08:00
Format                          : application/pdf
Title                           : Microsoft Word - Yokomo_BL-WM_USER_MANUAL
Creator                         : Administrator
Document ID                     : uuid:154f95fb-eeea-430a-969a-e4469f1fcd8b
Instance ID                     : uuid:c17c149b-a167-44c6-8d55-1befee279a46
Page Count                      : 4
Author                          : Administrator

EXIF Metadata provided by EXIF.tools