GUANGZHOU U and I TECHNOLOGY BS186FP TWS Bluetooth Headset User Manual 15 BS186FP UserMan
GUANGZHOU U&I; TECHNOLOGY COMPANY LIMITED TWS Bluetooth Headset 15 BS186FP UserMan
15_BS186FP UserMan
BS186FP Structure Sketch TWS Bluetooth Headset User Manual Erect headset and place them into the cochlea 1)MFB(multifunction button) 2)Indicator light(MIC) 3)Speaker 4)The charging contact point Step② Slightly rotate headset until it firm 5)ON/OFF for the base 6)Charging base indicator 7)Micro USB charging port Bluetooth Version: V5.0 Support: HSP,HFP,A2DP,AVRCP Audio Decoding Protocol: SBC,AAC Transmission Power: Class 2 Operation Range: Up to 10 meters Frequency Range: 2.4GHz-2.48GHz Battery of Headset: 45mAH Li-polymer Battery Charging Voltage of Headset: DC 5±0.25V Charging Time of Headset: About 1.5 hours Music Playing Time:* ≥3 hours Talk Time:* ≥3 hours Standby Time:* About 85 hours Call Mode Driver: φ6mm Driver sensitivity : 93db/1kHz Headset Charging Mode Driver impedance: 16Ω±15% Driver frequency ring range: 20Hz-20kHz Charging Base Charging Mode Power On State After power on the indicator light flashes blue for 3 times. Power Off State When power off the indicator light flashes red for 4 times. Low Voltage Alarm State The indicator light flashes red once every 20 seconds Dimensions of single headset(mm): L19.5×W19.5×H26 Weight of single headset(mm): About 4.8g Chagring base specifications Charging base battery specifications: 460mAH Li-polymer Battery Charging base voltage: DC 5±0.25V Charging time of base: About 2 hours Step③ Headset status Status No. Status Make the headset to cochlear edge tightly. Headset Performance Identify according to L&R and wear the headset (R) and headset (L) respectively 2-3times Charging base size (mm): L80×W33×H31 Weight(Total): About 58g *The time mentioned above may vary due to user's operation mode and device settings. Method Charging Ways of Headset The indicator light of headset is red when being charged, and will turn off automatically after being fully charged Put the headset (L) (R) to the corresponding position in the bottom of the charging base, and press the charging base switch. Charging Ways of Charging Base Use the USB charging cable to charge Headset(R) Headset(L) Note 1: Check the charging device suits to the headset or not. Note 2: Use only the supplied charger to charge the headset, if using other device it may violate or the maintenance article of this product and may cause danger. Note 3: Do not attempt to force open the built-in battery as this could damage the headset. Note 4: A fully charged headset will lose its power automatically if left unused. It is recommended to charge the headset each three months. Note 5: Do not leave the headset in a too hot or too cold condition (best between -10℃ and 50℃) which may affect the headset's operations although it is fully charged. r. Note 6: Do not dispose of the headset into fire or water. Note 7: Please bounce up the changing base switch if the headset idles for a long time to avoid power consumption. In OFF MODE, press and hold headset(R) or headset(L) MFB for 2 seconds to turn on. In ON MODE, press and hold headset(R) or headset(L) MFB for 5 seconds to turn off. When in a call, the indicator light of the headset flashes red every 5 seconds The indicator light of the headset is red when being charged, and will turn off automatically after being fully charged The indicator lights of the charging base flashes when being charged, and four lights are on after being fully charged Use the USB cable to connect with mobile phone charger Turning ON/OFF The Single Pairing The indicator light of headset(R) flashes red and blue alternately headset(R) After TWS pairing successed, the indicator light of right headset alternately flashing red and blue; When the right TWS Pairing headset pairing successfully with mobile phone, the indicator light flashes blue once every 5 seconds The indicator light of the headset flashes blue once every Standby Mode 5 seconds Charging Headset Times from Charging base: Use the USB cable to connect with computer Bluetooth headset should be used with the compatible devices which support Bluetooth wireless technology. This allows you make two calls and enjoy the music streaming at any time freely. Please read this user manual carefully before using the headset, and also read your device’s user manual regarding the Bluetooth function, and pay attention to those important safety and maintenance information. Please keep the headset away from children. Headset specifications Wearing Steps: Step① Method Pick up the headsets from the charging base to turn on automatically. Put them back to power off and charge the headset. (Make sure the charging base switch is pressed down) TWS Pairing 2s Note: • The main headset and vice headset speakers will emit "Connected", (L) prompts "Left Channel", (R) prompts "Right Channel" at the same time, and the main headset prompts "Second Device connected" after successful connection with the mobile phone. • After the headset has used the switching function, both the left and the right headset can be used as the main ear, it will not affect the use. 接听/挂断电话/ Ending a Call Answering On OFF state, press MFB of headset (R) or headset (L) for 2 seconds to power on and waiting for about 10 seconds , the two headsets will enter auto-pairing mode. The two headsets connect with each other after few seconds, the headset (R) alternately flashing red and blue, and then open the phone's bluetooth device to search “BS186FP”. Pick up the two headsets from the charging base to power on and waiting for 10 seconds , the two headsets will enter auto-pairing mode. The two headsets connect with each other after few seconds, the headset (R) alternately flashing red and blue, and then open the phone's bluetooth device to search. Bluetooth ON BS186FP Auto Transfering between R & L headset TWS firstly use the default right headset as the main heaset and left headset as the vice headset. But when the main headset is turned off, the vice headset will automatically connect with the mobile phone and can be used individually. And the turned-off headset will quickly reconnected with the main headset and work normally after restarting. TWS Reconnected Method1: Press headset (R) and (L) multifunction button at the same time for 2 seconds to power on → wait for several seconds and the two headsets will automatically connect → wait a few seconds for the headset to connect with the paired phone → re-connection successfully. Method2: When you pick up the headset from the charging case after 3 seconds to power on→wait for a few seconds, the two headsets will automatically connect→wait for a few seconds, the headset will be linked with the paired mobile phone→ re-connection successfully. On standby mode, shortly press MFB of headset(R) or headset(L) to play music. On music playing state, double-click MFB of headset(R) to PAUSE music. But headset(L) can not pause music independently. • When incoming call, short press MFB of headset (R) or headset (L), the speaker prompts once “Du” to answer call; In call mode, long press MFB of headset (R) or headset (L) for 2 seconds heard twice“Du” to end a call. Adjusting the Volume In call mode or music mode, shortly press MFB of the headset(R) to volume up and shortly press the headset(L) to volume down. Once “Du” can be heard when volumne is up to maximum or minimum The instructions of headset charging power switch 1. When switch button is pressed,headsets charging position 5V probe is normal output and headsets can be charged normally. When switch button is bounced,headsets charging position 5V probe output off,headsets can not be charged and will automatically on. Please off headsets manually at this time. After headsets are off, they can be stored in charging base,which will not consume battery power of charging base. 2. If switch button is pressed and no use for a long time,headsets will run out of charging base battery power. Forward/Backward Rejecting a call Press and hold MFB of headset(R) or headset (L) for 2 seconds to reject the call, the speaker prompts twice “Du” and “call reject”. Do as the above ways: 1 or 2 , after TWS successfully paired: left headset prompts "left channel" and right headset prompts "right channel-pairing" Cell phone begins to search for bluetooth devices (see the user guide of your phone for instructions). Mobile phone to search for “BS186FP” and select the “BS186FP”. Music Pause/Playing Siri or Google Assistant function On standby mode or music playing state, double-click the secondary headset (L) function key, which can be heard once "Du". Note:This feature only supports mobile phones with voice dial-up functions. Two-call Handling (Only support the mobile phone which has the function of handling two phones.) When you are answering a call, there is another call coming : 1.Long press and hold MFB of headset(R) for 2 seconds to end the current call and answer incoming call; 2.Short press MFB of headset(R) to hold the current call and answer incoming call; 3.After the second implementation, short press MFB of headset(R) to switch between two calls; 4.After the second implementation, long press MFB of headset(R) for 2 seconds to end the current call, and long press MFB of headset(R) for 2 seconds to end the other call. Note: All the above operations have to respect the precondition supported Bluetooth hands free profile V1.5 and Phones are running holding function (Network services) from telecom. In playing music, long press the (R) multi-function button for 3 seconds till hear the twice “DuDu” and release then next song; Long press the headset(L) multi-function button for 3 seconds till hear twice “Du Du”. release after the prompt, then last song. Delete Pairing Records on the Headset In any state, press and hold the headset multi-function button for about 10 seconds (off state)→ ON MODE(2 seconds)→ Delete pairing records(10 seconds), until hearing the “Du” voice for 3 times, and the red/blue light flashes twice at the same time. Function Instruction of Charging Base The instruction of charging base indicator light Four blue indicator lights, each of which represents 25% of the battery. Charging base indicator light On charging mode of charging base,flash blue indicator light. · One light is always on, which means charging base battery power fully charged by 25%; · Two lights mean charging base battery power has been fully charged by 50%; · Three lights mean charging battery power fully charged by 75%; · Four lights mean charging base battery power fully charged by 100%. Charging base battery display When no charging but opening the charging base, after four indicator flash in turn (about 1.5 seconds to complete flash), the indicator will light on for about 5 seconds to show how much battery is left (after 5 seconds, indicator lights all off ). · One light is always on, which means charging base battery power fully charged by 25%; · Two lights mean charging base battery power fully charged by 50%; · Three lights mean charging base battery power fully charged by 75%; · Four lights mean charging base battery power fully charged by 100%. When the switch is bounce, is a raised state. When the switch is pressed, is flush with the surface of the charging base. Maintenance • Do not use abrasive cleaning solvents to clean the headset. • Do not allow the headset to touch with any sharp objects as this will cause scratching and damage • Please keep headset away from high-temperature, humidity and dust. Common Faults and Exclusion Faults Reasons Solutions Can not turn on low battery protection Charging headsets for 2-3 hours Can not turn on by picking up the headset /No indicator light when headset being charged Charging base low battery protection Charging both the headsets and charging base for 2-3 hours No sounds pairing Wrong pairing Pairing again Too many pairing records Delete pairing records according to user manual Charging base without DC power supply doesn’t indicator light when output power charging Check whether the micro USB charging line is plugged or the power switch is on Headsets without indicator light when charging The headsets couldn’t being charged in charging base 1)Checking headset charging interface whether has touched to POGO PIN of charging base and the location is correct or not. 2)Charging for charging base 3) whether the button is pressed state Turning off automatically Low battery Charging headset for 2-3 hours Headset echo Volume is too loud environment is noisy after The two headsets TWS pairing failure/TWS paired successful but can not find the headset(R) or Adjust the volume at phone or change a place Environmental interference Change a place or move to caused or distance between close the headset and mobile headset and mobile is too far Adjusting wearing position of Low voice of the calling Wearing headset is wrong headset party The charging base without Charging for charging base power, the headset will auto turn The headset no on and paired charging after put Press the headphone charging The headset charging power back to the charging power switch switch bounce base Noise in call Wearing headset is wrong Adjusting wearing position of headset NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Format : application/pdf Title : BS186FP 英文说明书 未转曲 FCC Metadata Date : 2018:08:13 18:09:47+08:00 Modify Date : 2018:08:13 18:09:47+08:00 Create Date : 2018:08:13 18:09:46+09:00 Creator Tool : Adobe Illustrator CS6 (Windows) Thumbnail Width : 148 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 15941 bytes, use -b option to extract) Instance ID : uuid:51a12024-0cfb-498c-b573-789a4050fb4a Document ID : xmp.did:6C936948D59EE8119901EF127193B58F Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:6B936948D59EE8119901EF127193B58F Derived From Document ID : xmp.did:6B936948D59EE8119901EF127193B58F Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:BDAD87ABC2C1E111BED484D3A664D8C3, xmp.iid:6C936948D59EE8119901EF127193B58F History When : 2012:06:29 16:16:04+08:00, 2018:08:13 18:09:44+08:00 History Software Agent : Adobe Illustrator CS5, Adobe Illustrator CS6 (Windows) History Changed : /, / Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : False N Pages : 1 Max Page Size W : 296.999615 Max Page Size H : 213.077778 Max Page Size Unit : Millimeters Font Name : ArialNarrow, ArialMT, Arial-BoldMT, Arial-BoldItalicMT, Myriad-Bold, MyriadPro-Bold, SimHei, AdobeSongStd-Light Font Family : Arial, Arial, Arial, Arial, Myriad, Myriad Pro, 黑体, Adobe 宋体 Std Font Face : Narrow, Regular, Bold, Bold Italic, Bold, Bold, Regular, L Font Type : Open Type, Open Type, Open Type, Open Type, Type 1, Open Type, Open Type, Open Type Font Version : Version 2.40, Version 2.95, Version 2.90, Version 2.90, 001.001, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329, Version 5.01, Version 5.017;PS 5.002;hotconv 1.0.67;makeotf.lib2.5.33168 Font Composite : False, False, False, False, False, False, False, False Font File Name : ARIALN.TTF, Arial_0.ttf, arialbd_1.ttf, arialbi_0.ttf, wmb_____.pfb; wmb_____.pfm, MyriadPro-Bold.otf, simhei.ttf, AdobeSongStd-Light.otf Plate Names : Cyan, Magenta, Yellow, Black, HKS 93 K, HKS 92 K Swatch Group Name : 默认色板组 Swatch Group Type : 0 Swatch Colorant Swatch Name : 白色, 黑色, CMYK 红, CMYK 黄, CMYK 绿, CMYK 青, CMYK 蓝, CMYK 洋红, C=15 M=100 Y=90 K=10, C=0 M=90 Y=85 K=0, C=0 M=80 Y=95 K=0, C=0 M=50 Y=100 K=0, C=0 M=35 Y=85 K=0, C=5 M=0 Y=90 K=0, C=20 M=0 Y=100 K=0, C=50 M=0 Y=100 K=0, C=75 M=0 Y=100 K=0, C=85 M=10 Y=100 K=10, C=90 M=30 Y=95 K=30, C=75 M=0 Y=75 K=0, C=80 M=10 Y=45 K=0, C=70 M=15 Y=0 K=0, C=85 M=50 Y=0 K=0, C=100 M=95 Y=5 K=0, C=100 M=100 Y=25 K=25, C=75 M=100 Y=0 K=0, C=50 M=100 Y=0 K=0, C=35 M=100 Y=35 K=10, C=10 M=100 Y=50 K=0, C=0 M=95 Y=20 K=0, C=25 M=25 Y=40 K=0, C=40 M=45 Y=50 K=5, C=50 M=50 Y=60 K=25, C=55 M=60 Y=65 K=40, C=25 M=40 Y=65 K=0, C=30 M=50 Y=75 K=10, C=35 M=60 Y=80 K=25, C=40 M=65 Y=90 K=35, C=40 M=70 Y=100 K=50, C=50 M=70 Y=80 K=70, PANTONE Cool Gray 7 C, C=0 M=0 Y=0 K=100, C=0 M=0 Y=0 K=90, C=0 M=0 Y=0 K=80, C=0 M=0 Y=0 K=70, C=0 M=0 Y=0 K=60, C=0 M=0 Y=0 K=50, C=0 M=0 Y=0 K=40, C=0 M=0 Y=0 K=30, C=0 M=0 Y=0 K=20, C=0 M=0 Y=0 K=10, C=0 M=0 Y=0 K=5, C=0 M=100 Y=100 K=0, C=0 M=75 Y=100 K=0, C=0 M=10 Y=95 K=0, C=85 M=10 Y=100 K=0, C=100 M=90 Y=0 K=0, C=60 M=90 Y=0 K=0, HKS 93 K, HKS 92 K Swatch Colorant Mode : CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK, CMYK Swatch Colorant Type : PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, SPOT, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, PROCESS, SPOT, SPOT Swatch Colorant Cyan : 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 14.999998, 0.000000, 0.000000, 0.000000, 0.000000, 5.000001, 19.999998, 50.000000, 75.000000, 85.000000, 90.000000, 75.000000, 80.000000, 70.000000, 85.000000, 100.000000, 100.000000, 75.000000, 50.000000, 35.000004, 10.000002, 0.000000, 25.000000, 39.999996, 50.000000, 55.000000, 25.000000, 30.000002, 35.000004, 39.999996, 39.999996, 50.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 85.000000, 100.000000, 60.000004, 25.000000, 10.000000 Swatch Colorant Magenta : 0.000000, 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 90.000000, 80.000000, 50.000000, 35.000004, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 30.000002, 0.000000, 10.000002, 14.999998, 50.000000, 95.000000, 100.000000, 100.000000, 100.000000, 100.000000, 100.000000, 95.000000, 25.000000, 45.000000, 50.000000, 60.000004, 39.999996, 50.000000, 60.000004, 65.000000, 70.000000, 70.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 75.000000, 10.000002, 10.000002, 90.000000, 90.000000, 0.000000, 0.000000 Swatch Colorant Yellow : 0.000000, 0.000000, 100.000000, 100.000000, 100.000000, 0.000000, 0.000000, 0.000000, 90.000000, 85.000000, 95.000000, 100.000000, 85.000000, 90.000000, 100.000000, 100.000000, 100.000000, 100.000000, 95.000000, 75.000000, 45.000000, 0.000000, 0.000000, 5.000001, 25.000000, 0.000000, 0.000000, 35.000004, 50.000000, 19.999998, 39.999996, 50.000000, 60.000004, 65.000000, 65.000000, 75.000000, 80.000000, 90.000000, 100.000000, 80.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 100.000000, 100.000000, 95.000000, 100.000000, 0.000000, 0.003099, 10.000000, 5.000000 Swatch Colorant Black : 0.000000, 100.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 10.000002, 30.000002, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 25.000000, 0.000000, 0.000000, 10.000002, 0.000000, 0.000000, 0.000000, 5.000001, 25.000000, 39.999996, 0.000000, 10.000002, 25.000000, 35.000004, 50.000000, 70.000000, 37.000000, 100.000000, 89.999405, 79.998795, 69.999702, 59.999104, 50.000000, 39.999401, 29.998802, 19.999701, 9.999103, 4.998803, 0.000000, 0.000000, 0.000000, 0.000000, 0.000000, 0.003099, 80.000000, 65.000000 Swatch Colorant Tint : 100.000000, 100.000000, 100.000000 Producer : Adobe PDF library 10.01 Page Count : 3 Creator : Adobe Illustrator(R) 16.0 For : Administrator, Bounding Box : -1145 -2885 -249 -1335 Container Version : 11 Creator Version : 16EXIF Metadata provided by EXIF.tools