Garmin Canada SDM-A Speed and Distance Monitor User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	667430
Application ID	inU9x8p55cLLGjuWd15Dyw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	300.04kB (3750499 bits)
Date Submitted	2006-06-12 00:00:00
Date Available	2006-06-12 00:00:00
Creation Date	2006-06-06 18:16:57
Producing Software	AFPL Ghostscript 8.14
Document Lastmod	2006-06-06 18:16:57
Document Title	Instructions SDM2 Wireless Speed and Distance Monitor 060606
Document Creator	PDFCreator Version 0.8.0
Document Author:	gbuckley

SDM2 Wireless
Speed and
Distance Monitor
USING THE SDM2 SPEED
AND DISTANCE MONITOR
The SDM2 Speed and Distance Monitor (foot
pod) must be attached securely on the shoe
of the user as shown. The pod must stay in
place on the shoe for optimum accuracy.
• Press the button for 1-2 seconds to
power on the pod. The red light
slowly blinks, indicating the pod is
powered on and sending data. If the
red light is solid, the pod is not
transmitting data and may require
service.
• After running, press and hold the
button to turn off the pod. The red
light becomes solid as the button is
held and then turns off as the pod
powers off.
PAIRING THE SDM2 SPEED AND DISTANCE MONITOR
WITH A SPORTS MONITORING WATCH
The SDM2 Speed and Distance Monitor must “pair” with an ANT-enabled sports monitoring watch in
order to display performance data to the user. Pairing is required only for first use and after a battery
change. To pair your monitor:
• Power on the SDM2 Speed and Distance Monitor. Bring the pod within 10-30 inches (25-75 cm) of
the sports monitoring watch.
• Ensure that you are standing at least 72 inches (183 cm) away from any other ANT-enabled speed and
distance monitor. You can be in proximity to other ANT-enabled devices.
• After the SDM2 Speed and Distance Monitor pairs with the sports monitoring watch, the running
shoe icon appears on the watch’s LCD display. The pod and the watch remain paired until a battery
change.
If the watch has previously paired with a different foot pod, subsequent re-pairing is necessary. The repairing procedure is similar to pairing except that the SDM2 Speed and Distance Monitor must be started
in RF Pair Mode. To power on the pod in RF Pair Mode, press and hold the button for 3-6 seconds. RF
Pair Mode lasts for 60 seconds and is indicated by a double-blinking red light.
Preliminary document not for redistribution. Product features and specifications may vary. Copyright ©2005 Dynastream Innovations Inc.
6/6/2006
REPLACING THE BATTERY ON YOUR
SDM2 SPEED AND DISTANCE MONITOR
Your SDM2 Speed and Distance Monitor uses one AAA battery, which is estimated to last 65-70 hours.
Power off the pod after running to lengthen battery life. The battery hatch is located on the front flat end
of the monitor and can be opened with a coin. Select a coin that fits the slot on the battery door. Insert the
coin into the slot and, applying firm downward pressure, turn the coin counterclockwise to open and
remove the battery door. Insert the battery with the positive end first. Replace the battery door. Insert the
coin into the slot and, applying firm downward pressure, turn the coin clockwise to close.
SPECIFICATIONS
Size (max dimensions):
Weight:
Sensors:
Power:
Battery life:
Storage temp:
Operating temp:
Water resistance:
User-interface:
Speed-distance computation:
Available data and accuracy:
Speed range:
RF frequency/protocol:
Communication range:
Regulatory compliance:
73 (L) x 41 (W) x 25 (H) mm
40 g
Dynastream SpeedMax sensor
Single user-replaceable AAA battery
Minimum 65-70 hours run time at 20°C when used as a running pod;
up to 2 weeks as an activity monitor
-20°C to +70°C
-10°C to +50°C
3 ATM for 24 hours
Wireless sports monitoring watches and other ANT-enabled
data-receiving products
Dynastream patented SpeedMax algorithms
Speed and distance – uncalibrated >97%, calibrated >99%
1.0-5.5 m/s (2.2-12.3 mph)
2.4 GHz / Dynastream ANT transmit protocol
> 3 m (receiver dependent)
FCC, IC, and CE
Preliminary document not for redistribution. Product features and specifications may vary. Copyright ©2005 Dynastream Innovations Inc.
6/6/2006
FCC Compliance
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the product warranty and the user’s authority to operate this equipment under Part 15
regulations.
Preliminary document not for redistribution. Product features and specifications may vary. Copyright ©2005 Dynastream Innovations Inc.
6/6/2006
Warranty Information
VENDOR Warranty: LIMITED WARRANTY This VENDOR product is warranted to be free from defects in materials or
workmanship for one year from the date of purchase. Within this period, VENDOR will at its sole option, repair or replace any
components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided
that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to abuse, misuse, accident
or unauthorized alteration or repairs. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN
LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDING ANY LIABILITY ARISING
UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR
OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE.
IN NO EVENT SHALL VENDOR BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL
DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR INABILITY TO USE THIS PRODUCT OR FROM
DEFECTS IN THE PRODUCT.
Warranty does not cover the receiver or the transmitter battery, damage due to misuse, abuse, accidents or non-compliance with the
precautions; improper maintenance, commercial use, cracked or broken cases.
Some jurisdictions do not allow the exclusion of incidental or consequential damages, so the above limitations may not apply to you.
VENDOR retains the exclusive right to repair or replace the unit or software or offer a full refund of the purchase price at its sole
discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. To
obtain warranty service, contact your local VENDOR authorized dealer. Or call VENDOR Customer Service at one of the numbers
shown below, for shipping instructions and an RMA tracking number. The unit should be securely packed with the tracking number
clearly written on the outside of the package. The unit should then be sent, freight charges prepaid, to any VENDOR warranty center.
A copy of the original invoice is required as the proof of purchase for warranty repairs. Products sold through online auctions are not
eligible for rebates or other special offers from VENDOR. Online auction confirmations are not accepted for warranty verification. To
obtain warranty service, an original or copy of the invoice from the original retailer is required. VENDOR will not replace missing
components from any package purchased through an online auction.
VENDOR CONTACT INFO HERE
Preliminary document not for redistribution. Product features and specifications may vary. Copyright ©2005 Dynastream Innovations Inc.
6/6/2006

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 4
Producer                        : AFPL Ghostscript 8.14
Create Date                     : 2006:06:06 18:16:57
Modify Date                     : 2006:06:06 18:16:57
Title                           : Instructions SDM2 Wireless Speed and Distance Monitor 060606
Creator                         : PDFCreator Version 0.8.0
Author                          : gbuckley
Subject                         : 

EXIF Metadata provided by EXIF.tools