Garmin 00447 Low Power Data Transmitter User Manual 190 00580 00 0A indd

Garmin International Inc Low Power Data Transmitter 190 00580 00 0A indd

Contents

users manual 2

Download: Garmin 00447 Low Power Data Transmitter User Manual 190 00580 00 0A indd
Mirror Download [FCC.gov]Garmin 00447 Low Power Data Transmitter User Manual 190 00580 00 0A indd
Document ID615508
Application ID9QZIclSfoQoBkO6vGdpq+w==
Document Descriptionusers manual 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize93.76kB (1172032 bits)
Date Submitted2005-12-27 00:00:00
Date Available2005-12-23 00:00:00
Creation Date2005-12-27 16:26:00
Producing SoftwareAdobe PDF Library 6.0
Document Lastmod2005-12-27 16:26:10
Document Title190-00580-00_0A.indd
Document CreatorAdobe InDesign CS (3.0.1)

GETTING STARTED
Configure the Edge
When you first turn on your Edge, the following setup screens appear.
Follow the on-screen instructions:
Screens 4 and
5 apply to Edge
305 only.
12
190-00580-00_0A.indd 12
Edge Owner’s Manual
12/1/2005 9:44:13 AM
GETTING STARTED
Acquire Satellite
Signals
Before you begin using the Edge,
you must acquire GPS satellite
signals. It may take 30-60
seconds to acquire signals.
To acquire satellite signals:
Go outdoors to an open area
away from tall buildings and
trees. Then press and hold
the Power button.
On the Satellite page, the
available satellites are
flashing while the Edge
searches for satellite signals.
Acquired satellites and each
corresponding bar below
change to solid.
The GPS accuracy appears at
the top of the page.
NOTE: You can turn off the GPS
receiver and use the Edge indoors.
See page 55.
Edge Owner’s Manual
190-00580-00_0A.indd 13
13
12/1/2005 9:44:14 AM
GETTING STARTED
Position the Heart
Rate Monitor
information on customizing the
data fields on your Edge.
NOTE: The heart rate monitor is an
accessory for the Edge 305 only.
Wear the heart rate (HR) monitor
directly on your skin, just below
the breastplate. It should be snug
enough to stay in place during
your workout. To view heart rate
information on your Edge during
a workout, you must add it to the
data fields on one of the data
pages. See page 53 for more
To use the heart rate monitor:
1. Push one tab on the elastic
strap through the slot in the
heart rate monitor.
2. Wet both sensors on the back
of the heart rate monitor to
create a strong connection
between your pulse and the
transmitter.
sensors
14
190-00580-00_0A.indd 14
Edge Owner’s Manual
12/1/2005 9:44:15 AM
GETTING STARTED
3. Attach the strap to the other
side of the heart rate monitor
around your chest.
NOTE: If you have trouble with
erratic heart rate readings, position
the transmitter on your back instead
of your chest, or try applying
electrode gel.
4. Tighten or loosen the strap as
necessary so that it fits snugly
against your body.
5. Turn on the Edge.
6. Bring it within range (3
meters) of the heart rate
monitor. The heart rate
monitor automatically
transmits your heart rate
to the Edge, and the heart
rate icon
changes from
flashing to constant.
Edge Owner’s Manual
190-00580-00_0A.indd 15
TIP: Be sure to move away from
other heart rate monitors while the
Edge is trying to “pair” with your heart
rate monitor and begin receiving
heart rate data. Once the Edge pairs
with your heart rate monitor, you can
go near other heart rate monitors. For
more information on pairing, training,
and troubleshooting, see pages
70-74.
15
12/1/2005 9:44:15 AM
GETTING STARTED
Position the GSC10TM
Sensor
NOTE: The GSC10 is an accessory
for the Edge 305 only.
To install the GSC10:
1. Place the GSC10 on the rear
chain stay. Loosely attach the
GSC10 using two cable ties.
Installing GSC10
Sensor
The Edge 305 CAD
includes a wireless speed
and cadence sensor. Both
magnets must be aligned
with their respective
indication line for the Edge
to receive data.
1 GSC10 on rear chain stay
reset button
cable ties
indication
line
16
190-00580-00_0A.indd 16
Edge Owner’s Manual
12/1/2005 9:44:15 AM
GETTING STARTED
2. Attach the pedal magnet
to the crank arm using the
adhesive mount and a cable
tie. Make sure the pedal
magnet is within 5 mm of the
GSC10 and the indication line
on the pedal magnet lines up
with the indication line on the
GSC10.
3. Attach the spoke magnet by
unscrewing the magnet from
the plastic piece. Then place
the spoke in the groove of
the plastic piece and tighten
slightly. The magnet can face
away from GSC10 if there is
not enough room between
sensor arm and spoke. Make
sure the magnet is aligned
with the sensor arm indication
line.
Edge Owner’s Manual
190-00580-00_0A.indd 17
2 pedal magnet on crank arm
cable tie
indication
line
4. Unscrew and move the
sensor arm to within 5 mm of
the spoke magnet. You can
also tilt the GSC10 closer to
either magnet for improved
alignment.
17
12/1/2005 9:44:16 AM
GETTING STARTED
5. Press the Reset button on the
GSC10. The LED light turns
red, then green. Pedal to test
the sensor alignment. The
red LED blinks each time the
crank arm passes the sensor,
and the green LED blinks
each time the wheel magnet
passes the sensor arm.
NOTE: This will test the first 60
passes. Press Reset again if you
require additional passes.
6. When everything is aligned
and working correctly, tighten
the cable ties, sensor arm,
and spoke magnet.
3 spoke magnet on wheel
spoke
magnet
pedal
magnet
18
190-00580-00_0A.indd 18
sensor arm
indication
line
Edge Owner’s Manual
12/1/2005 9:44:17 AM
GETTING STARTED
Set Your User Profile
The Edge uses information
that you enter about yourself to
calculate calorie consumption.
Set your user profile before you
begin using the Edge to ensure
it is recording accurate workout
data.
To set your user profile:
1. Press mode to access the
Main Menu.
2. Select Settings > User
Profile.
3. Enter your Gender, Birth
Date, and Weight.
If you are setting your user profile
for the first time (Edge 305 with
heart rate monitor), a Max HR
message appears. Select Yes to
adjust your maximum heart rate
calculation based on your user
profile.
TIP: When finished selecting options
or entering values on your Edge,
press the mode button to exit the
field or page.
Edge Owner’s Manual
190-00580-00_0A.indd 19
19
12/1/2005 9:44:17 AM
GETTING STARTED
Set Your Bike Profile
You can set up to three profiles.
To set your bike profile:
1. Press mode to access the
Main Menu.
2. Select Settings > Bike
Profile.
5. If you have an Edge 305
with the GSC10 speed and
cadence sensor on your bike,
select the Sensor Mounted
check box.
6. In the Wheel Size field, select
Auto to have the GSC10
automatically detect your tire
size using GPS data or select
Custom to enter your tire
size.
Change the Backlight
and Contrast Settings
3. Select the bike profile you
wish to use.
4. Enter the Bike Weight.
20
190-00580-00_0A.indd 20
To change the Edge display:
1. Press mode to access the
Main Menu.
2. Select Settings > Display.
Edge Owner’s Manual
12/1/2005 9:44:17 AM
GETTING STARTED
3. Select the amount of time the
backlight stays on. Use a low
backlight timeout setting to
conserve battery power.
4. Select the amount of screen
contrast.
NOTE: You can also adjust the
screen contrast on the Satellite page
using the
arrows.
Edge Owner’s Manual
190-00580-00_0A.indd 21
21
12/1/2005 9:44:17 AM
TRAINING
TRAINING
The Edge offers several training
features and optional settings.
Use your Edge to set goals
and alerts, train with a Virtual
Partner™, program workouts, and
plan courses based on existing
rides.
Auto Pause/Lap
You can set the Edge to pause
the timer automatically during
your ride when you stop moving
or your speed drops below a
custom value. This setting is
helpful if your course includes
stop lights or other places where
you need to slow down or stop.
When you turn on Auto Pause,
the Edge stores any paused time
as Rest Time and any paused
22
190-00580-00_0A.indd 22
distance as Rest Distance. To
add these data fields to a custom
page, see page 53.
You can use the Auto Lap Trigger
feature to automatically mark
the lap at a specific position or
after you have traveled a specific
distance. This setting is helpful
for comparing your performance
over different parts of a workout
(each mile or kilometer or a major
hill, for example).
To set Auto Pause/Lap:
1. Press mode to access the
Main Menu.
2 Select Training > Auto
Pause/Lap.
3. In the Auto Timer Pause
field, select When Stopped
or Custom Speed to enter a
value.
Edge Owner’s Manual
12/1/2005 9:44:17 AM

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 11
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:f1589501-84a2-48f7-8a44-5c5f5cc65867
Modify Date                     : 2005:12:27 16:26:10-05:00
Create Date                     : 2005:12:27 16:26:00-05:00
Metadata Date                   : 2005:12:27 16:26:10-05:00
Document ID                     : uuid:92de4892-efad-4917-b184-1bb3b0924b93
Format                          : application/pdf
Title                           : 190-00580-00_0A.indd
Creator                         : Adobe InDesign CS (3.0.1)
Producer                        : Adobe PDF Library 6.0
EXIF Metadata provided by EXIF.tools
FCC ID Filing: IPH-00447

Navigation menu