Garmin 01653 Marine VHF Radio User Manual

Garmin International Inc Marine VHF Radio

a href="https://usermanual.wiki/Garmin" itemprop="url"> Garmin >

User Manual

                       A01653Installation Instructions.............................................................................. 2Instructions d'installation............................................................................ 5Istruzioni di installazione............................................................................ 8Installationsanweisungen.........................................................................11Instrucciones de instalación.....................................................................15Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express permission of Garmin.NMEA® and NMEA 2000® are registered trademarks of the National Marine Electronics Association. Other trademarks and trade names are those of their respective owners.El número de registro COFETEL/IFETEL puede ser revisado en el manual a través de la siguiente página de internet.September 2016 190-02061-93_0APrinted in China
972.48A01653 Series InstallationInstructionsImportant Safety Information WARNINGSee the Important Safety and Product Information guide in the product box forproduct warnings and other important information. CAUTIONAlways wear safety goggles, ear protection, and a dust mask when drilling,cutting, or sanding.NOTICEWhen drilling or cutting, always check what is on the opposite side of thesurface.Registering Your DeviceHelp us better support you by completing our online registration today.• Go to http://my.garmin.com.• Keep the original sales receipt, or a photocopy, in a safe place.Contacting Garmin® Product Support• Go to www.garmin.com/support for in-country support information.• In the USA, call 913-397-8200 or 1-800-800-1020.• In the UK, call 0808 238 0000.• In Europe, call +44 (0) 870 850 1241.Mounting ConsiderationsNOTICEThis device should be mounted in a location that is not exposed to extremetemperatures or conditions. The temperature range for this device is listed inthe product specifications. Extended exposure to temperatures exceeding thespecified temperature range, in storage or operating conditions, may causedevice failure. Extreme-temperature-induced damage and relatedconsequences are not covered by the warranty.When selecting a mounting location, you should observe these considerations.• The location should provide optimal viewing as you operate your boat.• The location should allow for easy access to all device interfaces, such asthe keypad, touchscreen, and card reader, if applicable.• The location must be strong enough to support the weight of the deviceand protect it from excessive vibration or shock.• To avoid interference with a magnetic compass, the device should not beinstalled closer to a compass than the compass-safe distance value listedin the product specifications.• The location must allow room for the routing and connection of all cables.Antenna Mounting and EME Exposure WARNINGRadio operators with cardiac pacemakers, life-support machines, or electricalmedical equipment should not be exposed to excessive radio-frequency (RF)fields, because the RF field may interfere with the function of their medicalequipment. CAUTIONThis device generates and radiates radio frequency (RF) electromagneticenergy (EME). Failure to observe these guidelines may expose people to RFradiation absorption exceeding the maximum permissible exposure (MPE).Garmin declares a MPE radius of   m (9797 in.) for this system, which wasdetermined using 25 W output to an omni-directional, 6 dBi gain antenna. Theantenna should be installed to maintain a distance of   m (  in.) betweenthe antenna and all people.Bail Mounting the DeviceNOTICEIf you are mounting the bracket on fiberglass with screws, it is recommendedto use a countersink bit to drill a clearance counterbore through only the topgel-coat layer. This will help to avoid cracking in the gel-coat layer when thescrews are tightened.Stainless-steel screws may bind when screwed into fiberglass andovertightened. It is recommended to apply an anti-seize lubricant on thescrews before installing them.You can use the included bracket to bail mount the device on a flat surface.1Using the bail-mount bracket À as a template, mark the pilot holes.2Using a 3.5 mm (9/64 in.) drill bit, drill the pilot holes.3Using the included screws Á, secure the bail-mount bracket to themounting surface.4Install the bail-mount knobs  on the sides of the device.5Place the device in the bail-mount bracket and tighten the bail-mountknobs.Flush Mounting the DeviceNOTICEBe careful when cutting the hole to flush mount the device. There is only asmall amount of clearance between the case and the mounting holes, andcutting the hole too large could compromise the stability of the device after it ismounted.If you are mounting the bracket on fiberglass with screws, it is recommendedto use a countersink bit to drill a clearance counterbore through only the topgel-coat layer. This will help to avoid cracking in the gel-coat layer when thescrews are tightened.Stainless-steel screws may bind when screwed into fiberglass andovertightened. It is recommended to apply an anti-seize lubricant on thescrews before installing them.The included template and hardware can be used to mount the device in yourdashboard.1Trim the template and make sure it fits in the location where you want tomount the device.2Using a 9.5 mm (3/8 in.) drill bit, drill one or more of the holes inside thecorners of the solid line on the template to prepare the mounting surfacefor cutting.3Using a jigsaw or rotary tool, cut the mounting surface along the inside ofthe solid line indicated on the template.4Place the device in the cutout to test the fit.5If necessary, use a file and sandpaper to refine the size of the cutout.6After the device fits correctly in the cutout, ensure the mounting holes onthe device line up with the pilot holes on the template.7If the mounting holes on the device do not line up, mark the new pilot-holelocations.8Using a 3.5 mm (9/64 in.) drill bit, drill the pilot holes.9Remove the template from the mounting surface.10 If you will not have access to the back of the device after you mount it,connect all necessary cables to the device before placing it into the cutout.11 If necessary, cover unused connectors with the attached weather caps toprevent corrosion of the metal contacts.12 Install the foam gasket À on the back of the device.The pieces of the rubber gasket have adhesive on the back. Make sureyou remove the protective liner before installing them on the device.2 Installation Instructions2.48 97
Download:
Mirror Download [FCC.gov]
Document ID3155973
Application IDKJSUVfK2IXOrF1zAfyzusA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize220.78kB (2759710 bits)
Date Submitted2016-10-04 00:00:00
Date Available2016-10-04 00:00:00
Creation Date2016-09-09 10:56:26
Producing SoftwareAntenna House PDF Output Library 6.2.625 (Windows (x64))
Document Lastmod2016-10-04 10:28:30
Document TitleUntitled
Document CreatorAH XSL Formatter V6.2 MR5 for Windows (x64) : 6.2.7.18952 (2014/11/12 16:18JST)
FCC ID Filing: IPH-01653

Navigation menu