Garmin 03023 Outdoor GPS User Manual

Garmin International Inc Outdoor GPS

Users Manual part 4of4

%DLO0RXQWLQJ,QVWUXFWLRQV:$51,1*See the Important Safety and ProductInformation guide in the GPS deviceproduct box for product warnings andother important information.Garmin® strongly recommends having anexperienced installer with the properknowledge of electrical systems install thedevice. Incorrectly wiring the power cablecan result in damage to the vehicle or thebattery and can cause bodily injury.&$87,21Always wear safety goggles, earprotection, and a dust mask when drilling,cutting, or sanding.NOTICEThe metal contacts on the GPS deviceand the mount should be kept dry to avoidequipment damage. Use the weather capon the mount at all times when the unit isnot mounted to keep the metal contactsdry and protected.To obtain the best performance and toavoid damage to your boat, install thedevice according to these instructions.Read all installation instructions beforeproceeding with the installation. If youexperience difficulty during the installation,contact Garmin Product Support.7RROV1HHGHG• Drill• Phillips screwdriver• 9.5 mm (3/8 in.) wrench or socket• 3 bolts or 3 screws:◦#8 (4 mm) pan-head machine boltswith nuts and washers, and a5 mm (5/32 in.) drill bit◦#8 (4 mm) pan-head self-tappingscrews and a 1.5 mm (1/16 in.) drillbit0RXQWLQJ&RQVLGHUDWLRQVNOTICEThe swivel base must be mounted usingpan-head machine bolts or self-tappingscrews. Using screws with countersunkheads can damage the mounting bracket.DRAFTAng an anoperms install thems install thehe power cablehe power cablethe vehicle or thethe vehicle or these bodily injury.dily injury.DRDRDD&$87,21safety goggles, earsafety goggles, ea dust mask whea dust mask whDDCEallallng with thng wiience difficulty dience diffntact Garmin Productntact Garmin Pr7RROV1HHGHG7RROV1HHGHG••DrillDrill•Phillips scPhil• 9.5 mm• 9.5 m•3 b3b
The device should be mounted in alocation that provides a clear view of thescreen and is easy to reach.The device should be mounted in alocation that is sturdy enough to supportthe mount and device.The device must be mounted in a locationthat allows room to route and connect thecables. You should allow at least 8 cm(3 in.) of clearance behind the case.0RXQWLQJWKH%UDFNHW$VVHPEO\Separate the swivel base ➀ from themount.Using the swivel base as a template,mark the pilot hole locations ➁.Select an option:• If you intend to secure the basewith machine bolts, drill three 5 mm(5/32 in.) holes.• If you intend to secure the basewith self-tapping screws, drill three1.5 mm (1/16 in.) starter holes.127(Do not make the holesdeeper than half of the screwlength.Secure the swivel base with the boltsor screws ➂.Place the swivel mount bracket ➃over the swivel base and secure it withthe short knob ➄.,QVWDOOLQJWKH0RXQWRQWKH0RXQWLQJ%UDFNHWAlign the slot ➀ on the back of thecradle with the long mounting knob ➁,2 Important Safety InformationDRAese as a tempse as a temations ations Tswivel bswivws ws ➂➂..
and slide the cradle into place on thebar.127(You can turn the long mountingknob to adjust the width of the bracketarms.Adjust the angle of the cradle, andtighten the long mounting knob untilthe cradle ➂ is secure.Rotate the swivel mount bracket ➃ toan optimal viewing angle, and tightenthe knob.The bracket clicks as you turn it.&RQQHFWLQJ3RZHUWRWKH0RXQWSelect a mounting location based onavailable power sources, safe cablerouting, and an unobstructed view.Connect the cables.Important Safety Information 3DRAFTe cradle, ande cradle, anounting knob untilnting knob untilsecure.securRotate the swivRotatan optimal vanthe knobthe kThe bThe b&RQ0
,WHP :LUH&RORU :LUH)XQFWLRQ➀Red Power➁Black Power➂Yellow Serial data input➃Blue Serial data output➄Green Serial ground wire➅Audio jackInsulate and secure unconnectedwires.,QVWDOOLQJWKH'HYLFHLQWKH0RXQWNOTICEBefore you place the device in the mount,ensure that the metal contacts on thedevice and the mount are dry. Moisture onthe contacts causes equipment damage.Use the weather cap to keep the mountcradle dry.Place the weather cap ➀ in thestorage area on the mount.Place the bottom of your device intothe cradle ➁.Tilt the device back until it snaps intoplace.4 Important Safety InformationDRAFTwireAARARARARAnnectednnec'HYLFHLQWKH'HYLFHLQWKHDCEce in thce in thPlace the bottomace thethe cradle the cradle ➁➁
Using the security screw tool, tightenthe security screw ➂ on the top of themount ➃.5HPRYLQJWKH'HYLFHIURPWKH0RXQWLoosen the security screw.Press the button ➀ on the side of themount to release the device.Lift the device out of the mount.Place the weather cap ➁ on thecradle.Important Safety Information 5DRAFTRPrew.rew.➀ on the side of theon the side of thee the device.the device.Lift the device oLift thPlace the wPlacradle.cradle
DRAFT
DRAFT
Garmin® and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Thesetrademarks may not be used without the express permission of Garmin.© 2011–2016 Garmin Ltd. or its subsidiariesPrinted in Taiwanwww.garmin.com/supportJuly 2016190-02006-92_ENDRAFT

Navigation menu