Garmin 03393 Part 15 Low Power Communication Device Transmitter User Manual Operating Manual

Garmin International Inc Part 15 Low Power Communication Device Transmitter Operating Manual

Operating Manual

Download: Garmin 03393 Part 15 Low Power Communication Device Transmitter User Manual Operating Manual
Mirror Download [FCC.gov]Garmin 03393 Part 15 Low Power Communication Device Transmitter User Manual Operating Manual
Document ID3675878
Application IDwqu+15R8WvQmodzZKpSUSA==
Document DescriptionOperating Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize61.28kB (765958 bits)
Date Submitted2017-12-13 00:00:00
Date Available2018-01-27 00:00:00
Creation Date0000-00-00 00:00:00
Document Lastmod0000-00-00 00:00:00
Document TitleOperating Manual

© 2017 Garmin Ltd. or its subsidiaries
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without
the written consent of Garmin. Garmin reserves the right to change or improve its products and to make
changes in the content of this manual without obligation to notify any person or organization of such
changes or improvements. Go to www.garmin.com for current updates and supplemental information
concerning the use of this product.
Garmin and the Garmin logo are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and
other countries.
and Garmin Canine™ are trademarks of Garmin Ltd. or its subsidiaries. These
trademarks may not be used without the express permission of Garmin.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by
Garmin is under license.
®
®
Table of Contents
Getting Started............................ 1
Device Overview ........... 1
Charging the Dog Collar Device .......... 1
Turning On the Dog Collar Device ....... 2
Attaching the Dog Collar Device to a
Collar Strap .......................................... 2
Pairing Your Smartphone with the Dog
Collar Device ....................................... 3
Fitting the Collar on Your Dog ............. 3
Garmin Canine............................. 4
Syncing the Dog Collar Device with the
Garmin Canine App ............................. 5
Bark Correction........................... 5
My device does not seem to be
active ................................................... 9
My device is not charging or does not
hold a charge ....................................... 9
My dog is still barking .......................... 9
My dog is barking too much ............... 10
Device Information.................... 10
Specifications .................................... 10
Sleep Mode ....................................... 11
Battery Replacement
Instructions ........................................ 11
Getting More Information ................... 12
Third-Party Software License
Agreement ......................................... 12
Index........................................... 14
Selecting a Training Mode ................... 6
Status LED Indicator ............................ 7
Correction Methods ............................. 7
Automatic Intensity .............................. 7
Choosing the Correct Intensity
Level .................................................... 8
Troubleshooting .......................... 8
The bark detection is too sensitive ...... 8
My dog collar device is not
responding ........................................... 8
Table of Contents
2 Plug the power cable into a power
source.
The color and number of lit status LED
indicators change as the collar
charges. All the status LED indicators
turn solid green when the device is
fully charged.
3 After all the status LED indicators turn
solid green, remove the USB cord from
the device.
NOTE: The device turns on
automatically when you remove it from
the charger.
Turning On the Dog Collar Device
seconds, a blue or green LED turns
red.
Turning Off the Dog Collar Device
Hold the power key until the status
LED turns solid red and the device
beeps.
Attaching the Dog Collar Device to
a Collar Strap
You can attach the dog collar device to a
collar strap that is a maximum of 25.4 mm
wide (1 in.) and 2.78 mm thick (0.11 in.).
1 With the buckle facing outward, insert
the end of the collar strap À through
the slot Á on the collar device.
The device remains on until you turn the
device off manually (page 2)
TIP: The device does not issue corrections
for two minutes after any button press, or
after the device is removed from the
charger.
Hold the power key until all of the
status LED indicators turn green.
The device beeps, and an LED
indicates the active mode. An LED
turns blue when the smart mode is
active. An LED turns green when any
other mode is active. After two
Getting Started
TIP: For bark correction, the device
should be positioned near the dog's
vocal cords. This location varies based
on the breed of dog. If the device does
not seem to detect the dog's barks,
you should move the device closer to
or farther from the dog's body to find
the ideal location.
2 Confirm that the ID tags on the collar
strap do not come into contact with the
device.
NOTE: ID tags contacting the device
may cause unintentional corrections.
3 Tighten the strap so that it is very snug
around the dog's neck, and fasten the
buckle.
NOTE: The collar should fit tightly and
should not be able to rotate or slide on
the dog's neck. The dog must be able
to swallow food and water normally.
You should observe your dog's
behavior to verify that the collar is not
too tight.
4 Wiggle the device to work the contact
points through the dog's coat.
NOTE: The contact points must have
contact with the dog's skin to be
effective.
Garmin Canine
The free Garmin Canine app allows you to
review your dog's daily activity and get
insights into your dog's behavior. The app
also allows you to wirelessly send
software updates to your dog device.
Set up bark correction: Allows the device
to detect and correct barks
automatically. You can adjust the
method of the corrections. When using
stimulation, you can adjust the
intensity level or use auto-rise.
Analyze your data: You can view
summary data, including your dog's
Garmin Canine
daily activity level and number of
barks. You can view more detailed
information about your dog's activity,
including event times and corrective
actions used.
Set up family members and dogs:
Allows you to create and edit dog
profiles, pair compatible dog collar
devices, and invite other family
members.
Syncing the Dog Collar Device with
the Garmin Canine App
Garmin recommends you sync your
device daily to review updated data in the
app and receive important notifications,
such as low battery alerts and software
updates.
1 Bring your smartphone within 10 m
(33 ft.) of the dog collar device.
TIP: You may need to wake the device
if your dog is stationary for a long
period of time.
2 Open the Garmin Canine app.
The dog collar device periodically
syncs data with the Garmin Canine
app automatically. The app indicates
when the last sync occurred.
®
Bark Correction
3 View your current data in the Garmin
Canine app.
Bark Correction
NOTICE
Before playing with your dog, you should
remove the dog collar device or deactivate
the correction feature.
When using the device, you should
remove all other collars, tags, or other
items from your dog. These other items
can cause the device to activate when the
dog is not barking.
The device can correct your dog
automatically when the dog barks. The
device detects vibrations to distinguish
between barking and other vocalizations.
You can use the Garmin Canine app to
manually adjust the amount of barking
allowed. You can allow no barking or set a
custom number to indicate how many
barks are allowed before correcting your
dog. You can also allow some barking (up
to 5 barks) to help avoid unintentional
corrections resulting from everyday
activity, such as yawning, sneezing, or
going through a dog door.
You can use any of these methods when
correcting your dog with the device.
• Tone
• Vibration
• Smart mode
• Stimulation
NOTE: If you turn off all correction
methods, the device continues to detect
your dog's barks without performing any
corrections. This can help you track your
dog's barking behavior using the Garmin
Canine app.
Selecting a Training Mode
When your device is paired with a
smartphone (page 5), you can use smart
mode. You must select smart mode on the
collar to use the settings in the Garmin
Canine app. When you do not select smart
mode during setup, the device defaults to
the last standard mode you used.
TIP: The device turns off when you hold
the button for more than three seconds.
When the mode is set in the app, the
center LED indicator turns blue and the
smart mode option becomes available
after you cycle through the standard
corrections. You must press the button to
see the current mode. When a correction
is issued in smart mode, the
corresponding LED indicates your
selected correction.
You can select a standard or smart mode.
1 Remove the collar band from the
device.
2 Press the mode button until the green
LED indicates the current mode.
3 Press the mode button within two
seconds to cycle the green LED
through the modes, and select a
mode.
NOTE: When the center LED is blue,
you can select smart mode.
After two seconds, the LED turns from
green to red, and the device issues a
sample correction of your selected
mode.
When you select stimulation mode, the
device does not issue a sample
correction.
If the device is in smart mode, the blue
LED cycles to a green, then a red LED
on the selected correction mode.
Bark Correction
Status LED Indicator
The center status LED indicators flashes
when the device detects a bark or has a
low battery charge.
LED
Activity
State
Flashing
white
Flashing
red
Status
A bark was
detected, and no
correction was
applied.
Correction
mode
A bark was
detected, and a
correction was
applied.
After a
correction
The battery is low.
Correction Methods
Stimulation: Applies a brief stimulation.
You can manually adjust the
stimulation intensity level using the
Garmin Canine app.
Tone: Activates an audible tone. A tone
can provide a patterned interruption to
stop a behavior. The tone can be more
effective when it is already associated
with a negative consequence or
alternate behavior.
Bark Correction
Vibration: Applies a vibration to the dog
for a short period of time to help break
focus on the current cause of a
behavior. The effectiveness of the
vibration may vary based on the dog's
temperament and experience.
Automatic Intensity
The device can set the stimulation
intensity level automatically based on the
barking behavior of the dog. The device
starts at the lowest intensity level and
increases the intensity level gradually until
the dog stops barking. When the dog is
quiet, the intensity decreases over time.
The automatic intensity feature is
designed to eliminate excessive nuisance
barking. To stop barks sooner, you should
set the intensity level manually.
The extended panic guard is a safety
feature that disables stimulation after four
corrections at the highest level, with 10
seconds between corrections. After the
fourth correction, the device waits until no
barks are detected in 2 minutes.
NOTE: When you set a fixed correction
level, the device does not enter extended
panic guard, even at the highest level of
correction.
Choosing the Correct Intensity
Level
You should choose the lowest intensity
level that discourages the dog from
barking. If you have never used a bark
correction collar with the dog, the dog
requires time and experience to learn that
the bark is the cause of the correction.
1 From the Garmin Canine app, set the
intensity to the lowest level.
2 For thirty minutes, when the dog barks,
observe the dog for a reaction, such as
a head shake, neck movement, a
change in the way the dog barks, or
just a change in expression.
3 If there is no reaction, increase the
intensity by one level until the dog has
a slight but recognizable reaction to
the stimulation.
4 Allow 24 hours for the dog to learn to
respond by not barking.
5 If the dog continues barking while
wearing the collar, increase the
intensity level gradually until you find
the level that discourages the dog from
barking.
Troubleshooting
The bark detection is too sensitive
If the feature activates when the dog is
not barking, or if the bark detection
appears to be too sensitive, you can try
these tips.
• Use the Garmin Canine app to adjust
the amount of barking allowed before
correcting your dog.
• Use the Garmin Canine app to turn off
the feature during heavy play, when
the dog is very active, or when the dog
is eating.
• Remove all other collars, tags, or other
items from your dog.
My dog collar device is not
responding
If the dog collar device stops responding,
you can try these tips.
• Verify the dog collar device is turned
on (page 2).
• Enable Bluetooth wireless technology
on your smartphone.
• Pair the dog collar device with your
smartphone (page 3).
Troubleshooting
•
•
•
Confirm that you are the only user
currently attempting to train the dog.
NOTE: Only one smartphone can be
connected to the dog collar device at a
time.
Check the battery level of the dog
collar device in the Garmin Canine
app.
NOTE: You should sync your dog
collar device with the Garmin Canine
app to view updated information and
battery level notifications.
Hold the power key for 10 seconds to
reset the dog collar device.
My device does not seem to be
active
When the device is active, the center
status LED flashes only when the device
detects a bark or motion.
• Verify the collar is turned on (page 2).
• Verify in the Garmin Canine app that
the battery is not low.
• Remove the device from the dog, and
shake the device briefly.
When the device is active, the device
detects the motion, and the center
status LED flashes.
Troubleshooting
My device is not charging or does
not hold a charge
If the device does not seem to be charging
or holding a charge, you can try these tips.
• Verify the charging connections are
secure (page 1).
• Verify the AC adapter and outlet are
functional.
TIP: To determine whether the adapter
is functional, you can plug the device
into your computer with a USB cord.
• Verify the status LED indicators are
green after charging.
• If necessary, replace the battery
(page 11).
My dog is still barking
If the dog continues barking while wearing
the device, you can try any of these
options to improve the effectiveness of the
device.
• Tighten the collar until it is very snug
(page 3).
• Adjust the position of the device on the
dog's neck (page 3).
• Wiggle the device to work the contact
points through the dog's coat.
•
Gradually increase the intensity level
(page 8).
•
My dog is barking too much
The device detects barks and, when paired
with the Garmin Canine app, shows when
barking occurs. You can use this
information to determine the cause of the
dog barking and take steps to prevent the
behavior. Each dog and situation is
different, and you should experiment to
discover what works for your dog.
TIP: Barking habits can change as a dog
ages. A younger dog can outgrow barking
behaviors, and an older dog can develop
new barking behaviors. You should
discuss sudden changes in barking
behavior with your veterinarian.
If you are home when the dog barks, you
can play with the dog or take the dog for a
walk. If the dog barks when you are not
home, you can take some precautions to
reduce barking.
•
10
Prevent the dog from seeing objects or
people that can trigger barking.
You can install privacy fencing for
outdoor dogs, and close the blinds or
curtains for indoor dogs.
•
•
Provide a safe place for the dog to
reduce anxiety barking.
The safe place should be cozy, limit
the view to outside stimuli, and include
a toy or food to occupy the dog.
Increase the physical and mental
activity of the dog. Some dogs are
vocal when they are bored.
You can increase the amount of
physical activity and engage the dog in
active training and play time.
Look for suggestions online
(page 12).
Device Information
Specifications
Battery type
Rechargeable lithium-ion
Battery life
Up to 30 days, typical use
Operating
From -20 to 60 C (from
temperature range -4 to 140 F)
Charging
From 0 to 40 C (from
temperature range 32 to 104 F)
Storage
From -20 to 70 C (from
temperature range -4 to 158 F)
(up to 1 month)
Device Information
Replacing the Dog Collar Device
Battery Assembly
Before you replace the battery, you must
remove all dirt, water, and debris from the
device. You also need the security
screwdriver included with the new battery.
You can purchase a replacement battery
assembly at http://buy.garmin.com. You
should use only a certified Garmin
replacement part. The battery assembly
includes a pre-assembled back plate with
a gasket, battery, and battery connector.
1 Remove the four security screws from
the corners of the device.
2 Lift up the battery assembly.
3 Grip the battery connector wires close
to the connector, and pull the
connector outward from the circuit
board to disconnect the battery
connector from the device.
4 With the new battery assembly,
connect the battery connector to the
device.
When properly installed, the connector
plug snaps into the port and the top
face of the connector plug is flush with
the edges of the port.
12
5 Verify the gasket is not damaged and
is completely seated in the groove.
6 Hold the battery assembly and the
device firmly together, and replace all
four security screws without tightening.
7 Verify the battery assembly and the
device are aligned with no gaps.
8 Tighten the screws evenly.
Getting More Information
You can find more information about this
product on the Garmin website.
• Go to support.garmin.com.
• Go to www.garmin.com/outdoor.
• Go to http://buy.garmin.com, or
contact your Garmin dealer for
information about optional accessories
and replacement parts.
Third-Party Software License
Agreement
Copyright © 2009-2012 ARM Limited.
All rights reserved.
Redistribution and use in source and
binary forms, with or without modification,
are permitted provided that the following
conditions are met:
Device Information
•
Redistributions of source code must
retain the above copyright notice, this
list of conditions and the following
disclaimer.
• Redistributions in binary form must
reproduce the above copyright notice,
this list of conditions and the following
disclaimer in the documentation and/or
other materials provided with the
distribution.
• Neither the name of ARM nor the
names of its contributors may be used
to endorse or promote products
derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND
CONTRIBUTORS "AS IS" AND ANY
EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL
COPYRIGHT HOLDERS AND
CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR
Device Information
CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED
AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
13
Index
accessories 12
apps, smartphone 3–5
bark correction 5, 7–9
battery 8, 9
replacing 11, 12
charging, collar 1
collar
attaching strap 2
charging 1
contact points 1
fitting 3
pairing 3
contact points 3, 9
pairing
collar 3
smartphone 3
power key 2
resetting the device 8
sleep mode 11
smartphone, pairing 3
specifications 10
training
modes 6
stimulation 7
tone 7
vibration 7
troubleshooting 8–10, 12
dog, status 7
dog collar device 3
history 5
intensity level 1, 9
automatic 7
choosing 8
14
Index


Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Page Layout                     : SinglePage
Page Count                      : 20
EXIF Metadata provided by EXIF.tools
FCC ID Filing: IPH-03393

Navigation menu