Garrett Metal Detectors SM100-00000 SM 100 User Manual 1538600 SM 100 Wireless REV B indd

Download:
Mirror Download [FCC.gov]
Document ID	2712420
Application ID	JjqRldTND0wPDtlMddktGw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	113.32kB (1416535 bits)
Date Submitted	2015-08-12 00:00:00
Date Available	2015-08-12 00:00:00
Creation Date	2015-08-11 13:35:30
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2015-08-11 15:38:38
Document Title	1538600_SM-100_Wireless_REV_B.indd
Document Creator	Adobe InDesign CS6 (Windows)

Installation and Operating Instructions
SM 100 Wireless Synchronization Module
# 1168800
USA
Security Division
Garrett Metal Detectors
1881 West State Street
Garland, Texas 75042-6797 USA
OUTSIDE USA
International Division
Garrett Metal Detectors
1881 West State Street
Garland, Texas 75042-6797 USA
Phone:
Fax:		
Email:		
Website:
Phone:
Fax:		
Email:		
Website:
972-494-6151
972-494-1881
security@garrett.com
www.garrett.com
972-494-6151
972-494-1881
international@garrett.com
www.garrett.com
SM 100 Wireless Synchronization Module
The Garrett SM 100 Wireless Synchronization Module allows the operation of multiple Garrett PD 6500i walk- through
metal detectors to operate in close proximity without the need for power line phase or wired synchronization. This
feature is especially important when the units are operated from battery power. A master unit can control a cluster of
slave units within approximately 20 feet. A cluster consists of one master unit and as many slave units as space allows.
Sixteen radio channels are available to allow the configuration of multiple clusters within a venue.
1.
1.1.1
1.2
1.2.1
Indicators
The module has two LEDs. The Communication Status LED indicates the status of communication between the host walk-through
and the sync module. The Walk-Through Link LED is used to confirm that the SM 100 is connected and communicating to the host
walk-through. The LED is illuminated when the connection is made and will blink at 15 second intervals and whenever the Operate
button on the walkthrough control panel is pressed, indicating data is being transferred. The Radio Link LED will illuminate when
the following conditions are met: 1) one SM 100 in a cluster is set to master and is active; 2) the frequency settings of the slave
walk-throughs is the same as the master; and 3) the distance between master and a slave module is within acceptable limits based
on environmental conditions.
Installation
Connecting the module requires removal of the control module cover located inside the control unit of the walk-through. Disconnect
the power cord, remove the three screws holding the cover, and remove. Connect the communication cable (provided) to the RJ-45
connector located on the left side of the circuit board. Connect the twisted wires (provided) to pins 1 and 2 of the plug-wire terminal
connector. These SYNC wires provide the synchronization pulses to/from the sync module depending on SYNC status and must be
connected correctly.
Connect the black (or dark colored) wire to pin 1 and the red (or light colored) wire to pin 2. See Figure 1.
CAUTION—An incorrect connection will cause unwanted interference between two or more detectors.
Figure 1
1538600_REV B, July 2015 © 2015 Garrett Electronics, Inc.
1.2.2 The SM 100 may be installed on top of or inside the detection unit of the PD-6500i. External placement provides additional range.
Internal placement protects the module from weather and tampering. Use the attaching strips to position the module as shown in
Figure 2.
Figure 2
(Above) Wireless Synchronization Module mounted internally. 		
(Above) Wireless Synchronization Module mounted externally.		
1538600_REV B, July 2015 © 2015 Garrett Electronics, Inc.
1.3
Configuration
		1.3.1
For large installations, the walk-through detectors should be organized into one or more clusters. Each cluster will consist of one
master and multiple slaves. It is recommended that a slave unit be placed within 20 feet of its master unit. Checkpoint spanning
greater distances may require multiple clusters. Use frequency offsets and a minimum distance of 10 feet between clusters to ensure
proper operation.
The SM 100 modules are used to synchronize the operation of the units to eliminate unit-to-unit interference. The configuration of
SM 100 module is controlled by the settings of the walkthrough to which it is attached. The settings that control the operation are
described in the PD 6500i User Manual. Refer to the section for Multiple Walkthrough Site Installation for configuration and spacing
requirements. The SM 100 modules will be used in place of the Synchronization Wires. Remember that the master unit must always
be operational if more than one unit in a cluster is switched on. The settings of each walkthrough must be as follows:
•
•
•
•
•
Synchronization—Make this selection through the menu setting on the PD 6500i. Set the Synchronization of one unit
in each cluster to master and all others in the cluster to slave.
Line Sync—
• Set the Line Sync for each master to Off which also sets the unit to Channel 1
• For slave Units, switch Line Sync to OFF to allow the selection of the Frequency value. Line Sync must then be switched
ON for Channel selection and operation.
Channel—Alternate the Channel settings on adjacent units between 1 and 2 starting with the master unit which will
always be in Channel 1.
Frequency—
• The Frequency setting provides a means for frequency offsets which are used to allow multiple walkthrough units
or multiple walkthrough clusters to operate without interference within a venue. Adjustments to frequency can also
be useful in eliminating interference from other walkthrough unit or from other electrical interference. The
allowable frequency range for this application is between 1970 and 2300. Refer to the manual for detailed information on
frequency selection.
• This frequency number is also the unique identifier that places a walkthrough into a synchronization cluster. For a
SM 100 in the master mode to be recognized, the walkthrough to which the slave SM 100 is connected must be set to
the same frequency as the SM 100 master unit.
• This number also controls the radio channel of the synchronization system. Each block of 39 consecutive frequencies
are assigned to one radio channel. When operating multiple clusters of walk-through detectors at a venue, select
frequency numbers for each cluster that are at least 39 numbers apart.
M Filter—Switch M Filter to OFF on each unit when operating multiple clusters in close proximity.
1.4
Operation
		1.4.1
1. Power on each walkthrough unit and verify that the LEDs on the wireless sync module light up as described above.
2. The Link Status LED should glow continuously (solid) to indicate proper radio frequency communication.
3. The Communication Status LED should blink at least once every 15 seconds.
3. Always verify that all SM 100 modules are connected and configured properly. Observe the bar graph activity and the ready light
on each unit for a period of time to be sure there is no interference between units. If interference is observed, check the settings on
each unit and/or switch the slave units off one at a time until the interference disappears. Re-check the settings and the connection
of the sync wires on pins 1 and 2 of the connector on the unit causing the problem.
For more information on walkthrough synchronization, please read the PD 6500i User Manual.
1538600_REV B, July 2015 © 2015 Garrett Electronics, Inc.
1.5
Limitation of the Wireless Sync Module
		1.5.1
The wireless sync modules communicate using radio frequency waves in the 2.4G Hz spectrum. As such, any physical obstacle that
might block the transmission of these waves could degrade functioning of this module. Examples of such obstacles include thick
walls and metal barriers.
		1.5.2
Successful reception of signal on the wireless sync module is limited to approximately a 20 feet radius from the master unit. This
distance may be reduced if there are obstacles between the master and slave units.
1.6
Regulatory
		1.6.1
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation. Any modifications to this equipment without the approval of the manufacturer will void the user’s authority to
operate the equipment.
This product complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference including interference that may cause
undesired operation of this device.
Ce produit est conforme avec Industrie Canada, exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux
conditions suivantes: (1) ce dispositif ne peut pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence y
compris les interférences qui peuvent causer un mauvais fonctionnement de ce dispositif.
1538600_REV B, July 2015 © 2015 Garrett Electronics, Inc.


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Instance ID                     : uuid:73f357ca-3ce3-4c99-99b4-6d48c5d63acb
Original Document ID            : adobe:docid:indd:a5b958aa-e331-11dd-a619-fef83d678f36
Document ID                     : xmp.id:E3DCADBE5740E51181D3E7F9775875C4
Rendition Class                 : proof:pdf
Version ID                      : 1
Derived From Instance ID        : xmp.iid:D1E9B5ED5640E51181D3E7F9775875C4
Derived From Document ID        : xmp.did:D1E9B5ED5640E51181D3E7F9775875C4
Derived From Original Document ID: adobe:docid:indd:a5b958aa-e331-11dd-a619-fef83d678f36
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2015:08:11 13:35:31-05:00
Create Date                     : 2015:08:11 13:35:30-05:00
Modify Date                     : 2015:08:11 15:38:38-07:00
Metadata Date                   : 2015:08:11 15:38:38-07:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Title                           : 1538600_SM-100_Wireless_REV_B.indd
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Page Count                      : 6
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools