Ge Small Dc Motors Fact Sheet

Ge-Small-Dc-Motors-Fact-Sheet-656393 ge-small-dc-motors-fact-sheet-656393

: Ge Ge-Small-Dc-Motors-Fact-Sheet-656393 ge-small-dc-motors-fact-sheet-656393 ge pdf

Open the PDF directly: View PDF .
Page Count: 180

Download
Open PDF In Browser	View PDF

Buyers’ Guide
Direct Current Motors
1-3000 HP

General Information

Page
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2

General
Information

Index

Air Flow Schematics: CD180AT through CD6900 Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5
Replacement Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7

Motor Pricing

Enclosures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3

SAM-QC Form: Basic Requirement Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.10
SAM-QC Form: Minimum Data Check Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.11

Modifications
Pricing

Motor Cutaway: Kinamatic™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Pump Motors: CD180AT through CD6900 Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.12

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

1.1

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

General Description

Introduction

Motor Finish

Designed to meet NEMA specifications, GE’s complete line
of DC motor offerings are available to meet all of your DC
motor needs. The Kinamatic™ and CD6000 series of motors
featured in this publication are a result of many years of
research and development. Quality components and
craftsmanship are designed to provide years of dependable
motor performance.

Our standard motor or generator paint is a machine tool
ANSI #49 grey, heavy duty acrylic enamel over a water based
primer. Polyurethane paint is available for waterproof motors.

Frames
Rugged magnetic ring frame construction of Kinamatic
motors and heavy duty fabricated CD6000 frames designed
for optimum motor performance.

Bearings
Antifriction bearings permit mounting of standard CD320AT
and below frame sizes at any angle and CD365AT-CD5010AY
frames mounted vertical shaft down. For easy maintenance,
CD6000 have antifriction bearings and removable bearing
cartridges and caps.

TREC® Field Coils
Tape Reinforced Encapsulated Construction (TREC®) of all
main field coils and commutating field coils is a process
which strengthens, seals, and bonds the coil to the pole to
form a single unit that is highly resistant to contamination,
vibration, impact, and wear.
The TREC coil is engineered to be elastic enough to withstand expansion and contraction due to temperature
differences. The TREC coil is standard on frames CD365ATCD5010AY and CD6000-CD6900.

Insulation
Kinamatic and CD6000 series DC motors have Class F
insulation containing a number of components rated Class
H, unless otherwise specified.
The insulation system employs many proprietary materials
and processes developed specifically for this line of machines.
The system was chosen to provide long life at rated loads and
also to withstand the effects of mechanical shock, vibration,
and the contamination of many severe environments. The
Class F insulation system has been proven by laboratory tests
and by many years of successful operation.

TIG Welding
Low maintenance, trouble free commutator riser joints are
provided by TIG (Tungsten Inert Gas) welding commutator
risers to the armature coil.
This strong copper-to-copper connection eliminates the use
of material with low melting temperatures and greatly
increases the motor’s ability to withstand overloads.

Terms

Other benefits of TIG welding include excellent mechanical
strength and overload capacity, no tin or lead contaminants,
and no throwing of solder.

(TREC® coils shown above)

Armature Treatment
Radiant Heat Process (RHP) All armatures in frames
CD180AT-CD500AT are treated with a solventless polyester
varnish, Radiant Heat Process. Armatures, in horizontal
position, are rotated under radiant electric heaters. After
preheating, the armatures are dipped and rotated under
heaters to cure the varnish. This process locks the resin in
place, filling the voids.
Vacuum Pressure Impregnation (VPI) All armatures in
frames CD6000-CD6999 are given a vacuum pressure
impregnation (VPI) treatment with high temperature varnish.
Armatures are placed into a vacuum vessel that pulls air
from the armature. Resin is then allowed into the vessel, and
pressure is applied. The pressure pushes the resin into the
voids. The armature is then drained and baked. Two VPI
cycles ensure an even varnish coating and an excellent heat
transfer path while eliminating all air pockets.
® Registered Trademark of General Electric Company

1.2

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Below is a listing of the enclosures offered by GE as defined by the National Electrical Manufacturer’s Association (NEMA). In
addition, the International Electrotechnical Commission (IEC).
Enclosure codes are shown for reference. This is a guide only. Refer to GE for special applications or labeling requirements.

IP-22

IC-01

DPFG-SV

Dripproof fully guarded, separately ventilated

IP-22

IC-17

DPFG-BV

Dripproof fully guarded, blower ventilated

IP-22

IC-06

ESV

Enclosed separately ventilated, air ducted in and out

IP-44

IC-37

SPFG

Splashproof fully guarded, self-ventilated

IP-23

IC-01

SPFG-SV

Splashproof fully guarded, separately ventilated

IP-23

IC-17

SPFG-BV

Splashproof fully guarded, blower ventilated

IP-23

IC-06

Protection

Cooling

TENV

Totally enclosed nonventilated

IP-44

IC-410

TEFC

Totally enclosed fan cooled

IP-44

IC-411

TEAO

Totally enclosed air-over-frame

IP-44

IC-416

TEAAC

Totally enclosed air-to-air cooled

IP-44

IC-666

TEWAC

Totally enclosed water-to-air cooled

IP-44

IC-86W

TENV-WP

Totally enclosed nonventilated, waterproof

IP-45/55**

IC-410

TEFC-WP

Totally enclosed fan cooled, waterproof

IP-45/55**

IC-411

TEAO-WP

Totally enclosed air-over-frame, waterproof

IP-45/55**

IC-416

Protection

Cooling

Totally Enclosed (TE)

Explosionproof (XP)
TENV-XP

Totally enclosed nonventilated, explosionproof

*

*

TEFC-XP

Totally enclosed fan cooled, explosionproof

*

*

TEAO-XP

Totally enclosed air-over-frame, explosionproof

*

*

Modifications
Pricing

Cooling

Dripproof fully guarded, self-ventilated

Accessories &
Modifications

Protection

DPFG

Motor Pricing

IEC Enclosures

Dripproof (DP)

Outline
Dimensions

NEMA Enclosures

General
Information

Enclosures

Terms

Other

Application
Information

* not defined
** IP-45: Drain Holes Open
IP-55: Drain Plugs Installed (special maintenance required)

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

1.3

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Enclosures

Dripproof, Fully Guarded
The standard Dripproof, Fully Guarded (DPFG) machine
allows successful motor operation when drops of liquids or
solid particles strike or enter the enclosure at any angle
from 0º to 15º downward from the vertical. Openings are
protected to prevent entrance of objects larger than 3/4”
in diameter.
Air openings are provided for easy conversion to splashproof
enclosure or for convenient connection of ducting for
separate ventilation.
CD180AT frame DPFG motors mounted sidewall and
vertical shaft end up will not be DPFG in that position,
but will be open fully guarded (OFG).

Dripproof Fully Guarded Self-Ventilated (DPFG)

Totally Enclosed
The standard Totally Enclosed Nonventilated (TENV) or
Totally Enclosed Fan Cooled (TEFC) motor provides effective
protection against adverse environmental conditions.
Among these conditions are dust, shavings, or other foreign
materials which are not classified as hazardous gas or dust
conditions. These machines are enclosed to prevent the
free exchange of air between the inside and outside of the
motor frame, but are not air-tight.

Explosionproof
The standard Explosionproof (XP) motor is a totally enclosed
machine with a housing constructed to contain any explosion within the motor caused by the hazardous atmosphere
entering the enclosure and being ignited. An explosionproof
motor prevents the equipment from triggering a general fire
or explosion.

Other

Application
Information

Totally Enclosed Fan Cooled (TEFC)

Terms

Totally Enclosed Fan Cooled Explosionproof (TEFC-XP)

1.4

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Air Flow Schematics

Dripproof Fully Guarded*, Blower Ventilated (DPFG-BV)

(CD218AT-CD5010AY frames have blower mounted on commutator end.)
*Could also be Splashproof Fully Guarded.

Blower positions and optional blower locations based on the position of the conduit box.
Frame Size
180AT

210AT to 5010AY

CB Location

CD6000 to CD6900

Blower Locations Available

Top

F1

CE-F1, F2

DE-F1, F2

F1

N/A

CE-F2, top

DE-F2, top

F2

N/A

CE-F1, top

DE-F1, top

NOTE: CE = comm end, DE = drive end
F1 = right side when viewed from the motor comm end, feet down
F2 = left side when viewed from the motor comm end, feet down

Terms
Terms

Other
Other

Dripproof Fully Guarded, Separately Ventilated (DPFG-SV)

Application
Application OutlineOutline
Accessories
Accessories
& Modifications
&
Modifications
Motor PricingMotor
Stock
Pricing
Motor
Information
InformationDimensions
Dimensions
Modifications
Modifications
Pricing
Pricing
Pricing

Dripproof Fully Guarded, Self-Ventilated (DPFG)

General
General
Information
Information

CD180AT-CD6900 Frames

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

1.5

Air Flow Schematics

Totally Enclosed Nonventilated (TENV)

Totally Enclosed Air-Over-Frame (TEAO)

Modifications
Pricing

Motor Pricing

General
Information

CD180AT-CD6900 Frames

Accessories &
Modifications

Totally Enclosed Fan Cooled (TEFC)

Totally Enclosed Air-to-Air Cooled (TEAAC)

Terms

Other

Application
Information

Outline
Dimensions

Totally Enclosed Water-to-Air Cooled (TEWAC)

Dwg. No. LO.MISC. 118R00

1.6

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Pricing: Use standard pricing given in this publication, plus
add for special shaft dimensions (page XX, item XX) and a
transition base (page XX, item XX).

3. Dimensional Duplicate (Obsolete duplicate)

This option applies only to older GE motors and is only
required when a mechanically interchangeable replacement
motor is not applicable (e.g., shaft height difference does not
1. Standard Replacement
allow for a transition base, or motor is coupled at both ends
The new motor will be our standard offering (Kinamatic
and a dimensional duplicate of the frame is required). the
motor shown in this publication) which duplicated the older
new motor will duplicate the older motor’s basic rating
motor’s basic rating (horsepower, armature volts, field volts,
(horsepower, armature volts, field volts, and field winding
and field winding type). The new motor will not duplicate the type). The new motor will duplicate critical dimensions of the
older motor’s winding characteristics (e.g., resistance,
older motor’s frame and shaft(s). the new motor will be
inductance, amperage, or regulation). The new motor will not updated with current electrical features, will not necessarily
duplicate the older motor’s drive end shaft dimensions or
duplicate the older motor’s winding characteristics (e.g.,
frame dimensions. The new motor will not duplicate the older resistance, inductance, amperage, or regulation). Standard
motor’s armature inertia, overall frame height, or overall
Class F rise, 1.0 service factor, and NEMA standard overloads
frame length. Standard Class F rise, 1.0 service factor, and
(as defined on page XX, item XX) will not apply unless
NEMA standard overloads (as defined in the Accessories and otherwise specified. The new motor will be supplied with the
Modifications section, page XX item XX) will apply unless
up-to-date versions of the accessories of the older motor.
otherwise specified. The new motor will be supplied with
Pricing: Refer to GE for producibility and pricing.
up-to-date versions of the accessories of the older motor.

This option is available if, and only if, the shaft height of the
older motor is reasonably higher (varies with motor size, but
typically greater than 1 inch is sufficient) than the shaft
height of the Kinamatic motor at the same rating. The new
motor will be our standard offering (Kinamatic motor shown
in this publication) which duplicates the older motor’s basic
rating (horsepower, armature volts, field volts, and field
winding type). By special machining the drive end shaft,

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Motor Pricing
Other

2. Mechanically Interchangeable Replacement
(Up-to-date replacement)

GE suggests that all non-direct motor replacement orders
be Print and Motor Data Approval Required. GE is not
responsible for mechanical or electrical replacement
problems encountered in the field.

Terms

Pricing: Use standard pricing given in this publication.

Modifications
Pricing

To replace a motor which has different mounting dimensions
than the Kinamatic motors shown in this publication (e.g., a
motor made by a different manufacturer or an older GE
motor), three options exist. When replacing a motor made by
a different manufacturer, all of the information listed on the
SAM-QC form (pages XX and XX) is required for quoting and
manufacturing. When replacing an older GE motor, the
model and serial number of the original motor are required
for quoting and manufacturing a replacement.

Accessories &
Modifications

Non-Direct Replacement

Outline
Dimensions

A GE DC motor with a model number which has the
format, 5CDNNNLLNNNLNNN, 5CDNNNLLLNNLNNN or
5BYNNNLLNNNLNNN (where N=number and L=letter) will be
replaced with an exact electrical/mechanical replacement of
the original motor. The new motor will be supplied with the
up-to-date versions of the accessories.

the new motor will duplicate the older motor’s mounting
dimensions. (C & FC dimensions may vary from original).
The new motor will not duplicate the older motor’s winding
characteristics (e.g., resistance, inductance, amperage, or
regulation). The new motor will not duplicate the older
motor’s armature inertia, overall frame height, or overall
frame length. Standard Class F rise, 1.0 service factor, and
NEMA standard overloads (as defined in the Accessories and
Modifications section, page XX, item XX) will apply unless
otherwise specified. The new motor will be supplied with the
up-to-date versions of the accessories of the older motor.

Application
Information

Direct Replacement

General
Information

Replacement Motors

1.7

Motor Cutaway

Quality, Reliability and Serviceability
A

NEMA Enclosures

C

B

Frames

D

•	 Round	steel	frames
•	 	Bored	to	provide	precise	seating	of	main	and	
commutating poles
•	 	Precision	rabbets	for	mounting	of	bearing	brackets

Outline
Dimensions

Bearings

•	 D
	 ouble	shielded	bearings	on	frames	CD180AT	-	CD2110AT
•	 	Open	ball	bearings	on	frames	CD258AT	-	CD5010AY
•	 	Regreasable	features	with	easy	access	alemite	fittings	to	
extend bearing life

•	 Dripproof,	Totally	Enclosed,	Explosionproof
•	 	All	enclosures	are	customizable	to	fit	specific
application requirements

Armature

•	 R
	 adiant	Heat	Process	(RHP)	on	CD180AT	-	CD5010AY	
frames
•	 	Dip	and	bake	process	cures	the	varnish,	preventing	voids	
and protecting against moisture and contaminates
•	 	Controlled	glass	banding	stabilizes	armature	to	withstand	
frequent starts, stops, and reversals
•	 	Commutator	risers	TIG	welded	to	armature	coils	-	
Eliminates hazards of tin or lead contaminates

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Kinamatic

B

J
G

Application
Information

H

I

D

E

C
Other

A

Terms

F

1.8

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Motor Cutaway

Brush Rigging

G

Easily	accessible
Oversized	fabricated	steel	box
Rubber	gasketed	mounting	and	clam	shell
Bronze	grounding	lug
Rotatable	360°	and	F2	mounting	capabilities	make	field	
adaptation easy in any application

Insulation

•	 Class	F	system	with	Class	H	components
•	 Withstands	effects	of	mechanical	shock,	vibration	
and contamination
•	 Long	life	at	rated	loads
H

Accessory Mounting Face

•	 Commutator	end	C-face
•	 Shaft	suitable	for	tachometer	and	speed	limit	switch
•	 Drilled	and	tapped	mounting	holes
I

J

Coils

•	 Random	Wound	Coils
- Frames CD180AT - CD329AT
- Wrapped with Mylar* composite and fiberglass tapes
- Dip and bake process allows varnish to penetrate
the windings
•	 TREC*	(Tape	Reinforced	Encapsulated	Construction)	Coils
- Frames CD360AT - CD5010AY
- Tightly seals coil to the pole, resisting outside
contamination, vibration, impact and wear
- Excellent heat transfer extends motor life
- Engineered to withstand thermal expansion
and contraction

Accessories &
Modifications

•	
•	
•	
•	
•	

Conduit Box

Outline
Dimensions

F

Modifications
Pricing

•	 Field	proven	design	that	requires	no	adjustment
•	 Heavy	cast	brush	holders	with	quick	release	brush	springs	
provide for easy maintenance
•	 Constant	pressure	springs	stabilize	brush	contact	to	
ensure proper commutation and improve brush wear

Application
Information

E

Motor Pricing

General
Information

Kinamatic

Lifting Lugs

Terms

Other

•	 Welded	into	frame	on	CD210AT	-	CD5010AY	frames
•	 Cast	in	endbell	on	CD180AT	frame
•	 Lifting	system	is	safer	than	a	single	eyebolt	lifting	system

* Trademark of General Electric Company.
Mylar® is a registered trademark of DuPont Tejin Films.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

1.9

SAM-QC Form

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Specify a Motor Quickly and Correctly

Basic Requirement
Instructions

The following form is designed to provide guidance through the minimum requirements needed to quote a DC Kinamatic or
CD6000 frame motor. To ensure GE meets your specific needs, each quote must include the following information:
A. Customer Identification Information
B. Basic Motor Description
C. Additional Modifications

Customer Identification Information
Section A – Identification information includes key customer details that will help establish a customer profile. This section
also includes the following information that, although not necessary, may be extremely helpful in distinguishing special
motor needs.
a. Model Number
b. Serial Number

Basic Motor Description
Section B – Basic Motor Description includes each of the following items and are essential in providing the correct motor
specifications to meet the needs of customer applications. These DC motor offerings can be reviewed for both the
Kinamatic and CD6000 frame motors in the “Standard Features” section on page ___ at the beginning of the motor
pricing tab.
1. Horsepower*
2. Base Speed*
3. Top Speed
4. Armature Voltage*
5. Field Voltage *
6. Type of Field*
7. Enclosure*
8. Orientation*
9. Mounting
10. Duty Cycle
11. Direction of Rotation
12. Temperature Rise
13. Ambient
14. Altitude
15. Service Factor
16. Conduit Box Location

Other

* Information REQUIRED to provide a quote

Additional Modifications

Terms

Section C – Additional Selections include all accessories featured in the “Accessories and Modification” section beginning on
page 3.1.

1.10

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

SAM-QC Form

General
Information

Minimum Data
Check Sheet

Check features that apply, and specify descriptions as needed

SECTION A – Customer Identification Information
Mounting:
p C-Face Footed
p D-Flange

Project Name:

p C-Face Footless
p P-Base

Motor Pricing

9.

Customer:

10. Duty Cycle:
p Continuous (Standard)
p Other (Please specify: e.g 30 min, 60 min)

Tracking Number:
Date:
Due Date:
Quote Number:

p Reversing (Standard)

a. Model Number:

p Clockwise

Modifications
Pricing

11. Direction of Rotation:
p Counter Clockwise

12. Temperature Rise:
p Class F

b. Serial Number:

p Class B

13. Ambient:

Horsepower*:

2.

Base Speed*:

3.

Top Speed*:

4.

Armature Voltage*:

p 3300 Ft (Standard)
15. Service Factor:
p 1.0 (Standard)
p 600

p Other
F1-RHS from CE (Standard)

p 150/300

Type of Field*:

SECTION C – Additional Modifications
p Stabilized Shunt
p Compound

Enclosure*:
p DPFG – Dripproof Fully Guarded
p DPFG-BV – Dripproof Fully Guarded Blower Ventilated
p DPFG-SV – Dripproof Fully Guarded Self-Ventilated
p TENV – Totally Enclosed Nonventilated
p TEFC – Totally Enclosed Fan Cooled
p TEWAC – Totally Enclosed Water-to-Air Cooled
p TEAAC – Totally Enclosed Air-to-Air Cooled
p TEAO – Totally Enclosed Air-Over-Frame
p TENV-XP – Totally Enclosed Nonventilated, Explosionproof
p TEFC-XP – Totally Enclosed Fan Cooled, Explosionproof

8.

16. Conduit Box:
Location:

Field Voltage*:

p Shunt Wound (Standard)
p Series
7.

p 750

p Other

Outline
Dimensions

p 500

p 100/200 p 120/240
p
Volts
6.

p Other

Modifications can be found on page 3.1 in section 3 of this catalog. Refer to
GE with any additional specializations.
List all additional modifications/accessories below, with details regarding
dimensions, size, requirements and etc.:

Orientation*:
p Horizontal (Standard)

p Vertical
p Shaft Up

Terms

5.

p 240
Volts

14. Altitude:

Other

p 180
p

p Other

Accessories &
Modifications

1.

p 40ºC (Standard)

Application
Information

SECTION B – Basic Motor Description

p Shaft Down

* Information REQUIRED to provide a quote

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

1.11

Pump Motors

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

CD180AT through CD6900 Frames

DESCRIPTION – Pump Motors
DC Motors with armature voltages from 105-130 Volts in
most cases are used in pump applications. These are special
motors built to pump manufacturer specifications. Because
of the low armature voltage these motors have special
electrical designs and in many cases frame sizes are larger
than standard. If a model number is not available, a request
for motors in this voltage range must be accompanied by
the following information.

Typically Motor RPM will be lower than nameplate speed
(approximately 10-15%) when cold and increase to nameplate RPM as main field reaches operating temperature.
To reduce the cold to hot speed variations, the shunt fields
should be energized at 50 to 70% of rated voltage to
stabilize. However, for ‘emergency’ pump motor applications,
where field pre-heating may not be feasible, the pump
capacity must be sized to the cold start RPM.

Pump motors operated from DC potential busses or
batteries will show significant speed variations from
nominal when the motor is cold and when the applied
voltage varies below nominal.

Also at lower than nominal voltage the motor will run
slower than nameplate RPM, while conversely the motor
will run higher than nameplate RPM when voltage is higher
than nominal.

PUMP FORM

Outline
Dimensions

Altitude

Customer:
Horsepower:
Enclosure:
Duty:

Temperature Rise:
p Class F

Base Speed:
p DPFG p TENV
p Explosionproof
p Cont.

Power Supply: p Battery

p TEFC
p Waterproof

p 60 Min.

°C

Feet (Standard is 3300 feet)

p 30 Min.

p Constant Voltage

p Class B

Service Factor: p 1.0

p 1.15

Rotation:

p CCW

p CW

Space Heater: Heater Voltage
p 120V p 240V

p Other
p None

Armature Voltage:

Volts

Thermostat:

p N.C.

Field Voltage:

Volts

Conduit Box:

p Standard

If Battery Supply: Anticipated Voltage Swing From
Nominal +/– What %?
Minimum Cold Running Speed and Voltage
Field Winding: p Shunt

p Compound

p Reversing

p N.O.

p Oversize

p Waterproof

Conduit Box Location: (as viewed from comm end of motor)
p Right Side p Left Side p Top
RPM

p Stab Shunt

Voltage

Mounting:

p Vertical Shaft Up
p Vertical Shaft Down
p Horizontal

Mounting Flange p C-Face
(If required)
p D-Flange
p P-Base

Drawings must be supplied for P-Base

Terms

Other

Application
Information

Max.	Ambient	Temp.		

Where Used:

1.12

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Motor Pricing

Page
Kinamatic™ Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2

General
Information

Index

180 Volt Motors, Self-Ventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4
180 Volt Motors, Totally Enclosed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5

Motor Pricing

CD6000 Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

240 and 500 Volt Motors, Separately Ventilated, 1 HP-7.5 HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7
240 and 500 Volt Motors, Self- and Separately Ventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8

Modifications
Pricing

240 and 500 Volt Motors, Self-Ventilated, 1 HP-7.5 HP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6

600 and 700 Volt Motors, Separately Ventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.13
Totally Enclosed Nonventilated Motors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.14
Totally Enclosed Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.15
Totally Enclosed Motors, Unit Cooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.16

Outline
Dimensions

600 Volt Motors, Separately Ventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.12

Accessories &
Modifications

500 Volt Motors, Separately Ventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11

Totally Enclosed Nonventilated, 60 Minute Motors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.22
Explosionproof and Dust-Ignitionproof Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.23
Papermill Duty Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.26

Application
Information

Totally Enclosed Nonventilated, 30 Minute Motors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.21

Papermill Duty, Splashproof Separately Ventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.27

Other

Papermill Duty, Totally Enclosed Nonventilated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.26

Terms

Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.29

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2.1

Standard Features

HP Range

1-500

Base Speed

300-3500 RPM

Armature Voltage

240V, 500V

Field Voltage

300/150V, 240/120V

Accessory Mounting

8.5" accessory mounting rabbet with accessory shaft extension

Agency Approvals

CSA

Altitude

3300 ft

Ambient

40°C

Balance/Vibration

Measured at top speed: Peak-to-Peak Amplitude 0.0015"

Bearing Caps

Cast iron CD258AT-CD5010AY both DE and CE

Bearing Type

Anti-friction ball, CDL182AT-CD2010AT: double shielded, CD258AT-CD5010AY: open

Coils

CD180AT-CD329AT random wound- dip and baked
CD360AT-CD5010AY TREC® Coils

Conduit Box

Fabricated steel, 360° rotatable, gasketed, oversized

Current Overload

Occasionally repeated loads of 150% of base speed full load current

Endbells

CD182AT-CD500AT: cast iron, CD5010AY: CE - cast iron, DE - fabricated steel

Frame Material

Rolled Steel

Frame Size

CD182AT-CD5010AY

Grease

Lithium soap base

Ground

Bronze bolt in conduit box

Insulation Class

Class F

Insulation System

Armature Treatment: Radiant Heat Process (RHP)

Lifting Means

Two (2) welded lifting lugs

Mounting

F1, modifiable to F2

Nameplate

Stainless Steel

Paint

ANSI #49 grey, heavy duty industrial enamel

Relubrication

CDL182AT-CD2110AT: pre-lubricated, CD258AT-CD5010AY: zerk grease fittings

Service Factor

1.0

Temperature Rise

Class F @ rated load and rated base speed

Tests

Routine Test: Report available upon request with purchase order

Warranty

24 months from date of installation or 30 months from date of manufacture; whichever occurs first

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Direct Current Motors
Kinamatic™

2.2

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

General
Information

Direct Current Motors
CD6000

300/150V

Accessory Mounting

8.5" accessory mounting rabbet with accessory shaft extension

Agency Approvals

CSA

Altitude

3300 ft

Ambient

40°C

Balance/Vibration

Measured at top speed: Peak to Peak Amplitude .0020"

Bearing Caps

Cast iron - both DE and CE

Bearing Type

Anti-friction ball bearings, open

Coils

TREC® Coils

Conduit Box

Large fabricated sheet metal construction with fixed buss-bar termination

Current Overload

Occasionally repeated loads of 150% of base speed full load current

Endbells

Fabricated Steel

Frame Material

Fabricated Steel

Frame Size

CD6000-CD6900

Grease

Lithium soap base

Ground

External mounting provision

Insulation Class

Class F

Insulation System

Armature treatment: VPI (vacuum pressure impregnation)

Lifting Means

Four (4) welded lifting lugs

Mounting

F1 modifiable to F2

Nameplate

Stainless Steel

Paint

ANSI #49 Grey heavy duty industrial enamel

Relubrication

Zerk grease fittings

Service Factor

1.0

Temperature Rise

Class F @ rated load and rated base speed

Tests

Routine Test: Report available upon request with purchase order

Warranty

12 months of operation / 18 months from date of manufacture; whichever occurs first

Accessories &
Modifications

500V, 600V

Field Voltage

Outline
Dimensions

300-1750 RPM

Armature Voltage

Application
Information

Base Speed

Other

500-3000

Terms

HP Range

Modifications
Pricing

Motor Pricing

Standard Features

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2.3

Dripproof Fully Guarded Motors

Self-Ventilated

General
Information

Class F Insulation
Type K Power Supply➁
For Continuous Operation in 40°C Ambient

PRICES - 180 Volts

PRICES - 180 Volts

Suitable for constant torque to 60% of base speed

Suitable for constant torque to 5% of base speed

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

HP

1
1.5

2

3

5
7.5

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

Enclosure ➂

Frame ➃

1750

2050

$4884

DP

L182AT ➄ •

1150

1380

$5472

DP

L182AT

2500

2750

$4798

DP

L182AT

1750

2050

$5108

DP

L182AT ➄ •

1150

1380

$5874

DP

186AT

2500

2750

$4890

DP

L182AT

1750

2050

$5330

DP

L182AT ➄ •

1150

1380

$6342

DP

186AT

2500

2750

$4540

DP

L182AT

1750

2050

$5166

DP

186AT ➅

1150

1380

$6766

DP

L186AT

2500

2750

$5146

DP

186AT
L182AT ➅ •

1750

2050

$5360

DP

1150

1380

$7778

DP

218AT

1750

2050

$8580

DP

219AT

Dim. Pg.

HP

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

Enclosure ➂

Frame ➃

1

1750

2050

$4886

DP

L182AT ➄ •

2500

2750

$4798

DP

L182AT

1750

2050

$4934

DP

186AT ➄ •

2500

2750

$5134

DP

186AT

1750

2050

$4934

DP

186AT ➄ •

2500

2750

$5134

DP

186AT

1750

2050

$5374

DP

L186AT ➅ •

2500

2750

$5420

DP

189AT

1750

2050

$8580

DP

219AT ➅ •

1.5
2
3
5

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.
➂ NV- Totally Enclosed Nonventilated
FC- Totally Enclosed Fan Cooled
DP- Dripproof Fully Guarded (Self-Ventilated).
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
➄ Stocked with 4.5” rabbet.
➅ Stocked with 8.5” rabbet.
C-FACE MODIFICATION NOT
➆ Stocked with 4.5” and 8.5” rabbet.
INCLUDED IN BASIC LIST PRICE.
10 Refer to GE for frame.

Application
Information

Outline
Dimensions

Type CD
Shunt Wound

Terms

Other

Dripproof Fully Guarded Self-Ventilated (DPFG)
(Frame CDL182AT shown above.)

2.4

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Dim. Pg.

Totally Enclosed Motors

Totally Enclosed

Class F Insulation
Type K Power Supply➁
For Continuous Operation in 40°C Ambient
For explosionproof motors, refer to page ??.

Suitable for constant torque to 5% of base speed

HP

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

Enclosure ➂

Frame ➃

3

1150

1380

$6990

FC

189AT

2500

2750

$6110

FC

189AT

1750

2050

$7108

FC

189AT ➅ •

5

Dim. Pg.

HP

1

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.
➂ NV- Totally Enclosed Nonventilated
FC- Totally Enclosed Fan Cooled
DP- Dripproof Fully Guarded (Self-Ventilated).
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
➅ Stocked with 8.5” rabbet.
C-FACE MODIFICATION NOT
➆ Stocked with 4.5” and 8.5” rabbet.
INCLUDED IN BASIC LIST PRICE.
10 Refer to GE for frame.

1.5

2

3
5

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

Enclosure ➂

Frame ➃

1750

2050

$4816

NV

L182AT ➆ •

1150

1380

$5150

NV

186AT

2500

2750

$4886

NV

186AT

1750

2050

$5086

NV

186AT ➆ •
L186AT

1150

1380

$6046

NV

2500

2750

$4984

NV

186AT

1750

2050

$5232

NV

L186AT ➆ •

1150

1380

$5418

NV

189AT

2500

2750

$5646

NV

L186AT

1750

2050

$5506

NV

189AT ➆ •

1150

1380

$5128

NV

2110AT

2500

2750

$7812

NV

2110AT

1750

2050

$10182

NV

2110AT ➅ •

3500

3500

$11284

NV

258AT

Dim. Pg.

Terms

Other

Application
Information

Outline
Dimensions

7.5

Base
Speed
RPM

Modifications
Pricing

PRICES - 180 Volts

Suitable for constant torque to 60% of base speed

Accessories &
Modifications

PRICES - 180 Volts

Motor Pricing

General
Information

Type CD
Shunt Wound

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2.5

Dripproof Fully Guarded Motors

Self-Ventilated

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

240 Volt Armature - 150/300V or 120/240V Field

500 Volt Armature - 150/300V or 120/240V Field

Suitable for constant torque to 60% of base speed

Suitable for constant torque to 60% of base speed

1

1.5

2

3

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

HP

Other

Application
Information

5

Terms

Type CD
Shunt Wound

7.5

Base
Speed RPM

Rated T op
Speed RPM

Basic List Price*
GO-2A

Frame ➃

1750

2300

$2198

L182AT

Dim. Pg.

1

Base
Speed RPM

Rated T op
Speed RPM

Basic List Price*
GO-2A

Frame ➃

1750

2300

$2972

L182AT
L182AT

1150

2000

$2476

L182AT

1150

2000

$3250

850

1750

$3202

186AT

850

1750

$3656

186AT

3500

3500

$1972

L182AT

3500

3500

$1972

L182AT

2500

3000

$2222

L182AT

2500

3000

$2222

L182AT

1.5

1750

2300

$2468

L182AT

1750

2300

$3242

L182AT

1150

2000

$2882

186AT

1150

2000

$3580

186AT

850

1700

$4300

186AT

850

1700

$5022

186AT

3500

3500

$2170

L182AT

3500

3500

$2170

L182AT

2500

3000

$2414

L182AT

2500

3000

$3188

L182AT

1750

2300

$3290

L182AT •

1750

2300

$3500

L182AT

1500

2100

$3066

10

1500

2100

$3066

10

1150

2000

$3346

186AT

1150

2000

$3580

186AT

850

1700

$4848

L186AT

850

1700

$5308

L186AT

3500

3500

$2466

L182AT

3500

3500

$2466

L182AT

2

2500

3000

$2788

L182AT

2500

3000

$3538

L182AT

1750

2300

$3938

186AT •

1750

2300

$3938

186AT •

1500

2100

$4126

10

1500

2100

$4126

10

1150

2000

$4740

L186AT

1150

2000

$5200

L186AT

850

1700

$5778

218AT

850

1700

$5778

218AT

650

1600

$6820

2110AT

650

1600

$6820

2110AT

3

500

1500

$8224

259AT

500

1500

$8224

259AT

400

1200

$10632

287AT

400

1200

$10632

287AT

300

900

$12578

327AT

300

900

$12578

327AT

3500

3500

$3214

186AT

3500

3500

$3214

186AT

2500

3000

$3772

186AT

2500

3000

$3772

186AT

1750

2300

$4914

L186AT •

1750

2300

$4914

L186AT •

1500

2100

$5300

10

1500

2100

$5300

10

1150

2000

$6064

218AT

1150

2000

$6064

218AT

850

1700

$7264

2110AT

850

1700

$7264

2110AT

650

1600

$8746

259AT

650

1600

$8746

259AT

500

1500

$11444

288AT

500

1500

$11444

288AT

400

1200

$13826

327AT

400

1200

$13826

327AT

900

$20212

365AT
186AT

5

300

900

$20212

365AT

300

3500

3500

$4336

186AT

3500

3500

$4336

2500

3000

$5032

L186AT

2500

3000

$5032

L186AT

1750

2300

$5994

218AT •

1750

2300

$5994

218AT •

1500

2100

$6464

10

1500

2100

$6464

10

1150

2000

$7318

258AT

1150

2000

$7318

258AT

850

1700

$8682

259AT

850

1700

$8682

259AT

650

1600

$11550

288AT

650

1600

$11550

288AT

500

1500

$13810

327AT

500

1500

$13810

327AT

400

1200

$16926

365AT

400

1200

$16926

365AT

300

900

$20212

368AT

300

900

$20212

368AT

7.5

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.

2.6

HP

www.gemotors.com

•

800-541-7191

Dim. Pg.

➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable

for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

GEP387M 09/11 • Prices and data subject to change without notice.

Dripproof Fully Guarded Motors

Separately Ventilated

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

240 Volt Armature - 150/300V or 120/240V Field

500 Volt Armature - 150/300V or 120/240V Field

Suitable for constant torque to 5% of base speed

Suitable for constant torque to 5% of base speed

$2198

L182AT

2

3

5

7.5

Rated T op
Speed RPM

Basic List Price*
GO-2A

Frame ➃

1750

2300

$2972

186AT

1150

2000

$2476

L182AT

1150

2000

10

10

850

1750

$3202

186AT

850

1750

10

10

3500

3500

$1972

L182AT

3500

3500

10

10

$2222

L182AT

2500

3000

10

10

2500

1.5

1

Base
Speed RPM

3000

1.5

1750

2300

$2468

L182AT

1750

2300

$3242

186AT

1150

2000

$2882

186AT

1150

2000

$3580

10

850

1700

10

10

850

1700

10

10

2500

3000

$3188

186AT

1750

2300

$3500

186AT

1500

2100

$3066

L186AT

2500

3000

$2414

L182AT

1750

2300

$2726

L182AT

1150

2000

$3346

186AT

2

850

1700

$4848

L186AT

1150

2000

$3580

L186AT

3500

3500

$2466

L182AT

850

1700

$4848

10

2500

3000

$2788

L182AT

3500

3500

$2466

10

3000

$3538

186AT

1750

2300

$3304

186AT

2500

1150

2000

$4740

L186AT

1750

2300

$3938

186AT

850

1700

$5778

218AT

1500

2100

$4126

L186AT

1150

2000

$4740

L186AT

850

1700

$5778

218AT

650

1600

$6820

2110AT

500

1500

$8224

259AT

400

1200

$9666

287AT

650

1600

$6820

10

1500

$8224

10

3

300

900

$11436

327AT

500

3500

3500

$3214

186AT

400

1200

$9666

10

2500

3000

$3772

186AT

300

900

$11436

10

1750

2300

$4914

L186AT

3500

3500

$3214

10

1500

2100

$5300

10

2500

3000

$3772

L186AT

1150

2000

$6064

218AT

1750

2300

$4914

L186AT

850

1700

$7264

2110AT

1500

2100

$5300

218AT

650

1600

$8746

259AT

1150

2000

$6064

219AT

500

1500

$10404

288AT

850

1700

$7264

2110AT

400

1200

$12570

327AT

650

1600

$8746

10

300

900

$14686

328AT

500

1500

$10404

10

3500

3500

$4336

186AT

400

1200

$12570

10

900

$14686

10
10

5

2500

3000

$5032

L186AT

300

1750

2300

$5994

189AT

3500

3500

$4336

1500

2100

$6464

10

2500

3000

$5032

10

1150

2000

$7318

2110AT

1750

2300

$5994

218AT
219AT

850

1700

$8682

259AT

1500

2100

$6464

650

1600

$10500

288AT

1150

2000

$7318

2110

500

1500

$12556

327AT

850

1700

$8682

259AT

400

1200

$15388

328AT

650

1600

$10500

288AT

300

900

$18376

329AT

500

1500

$12556

327AT

400

1200

$15388

328AT

300

900

$18376

368AT

7.5

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Dim. Pg.

Motor Pricing

2300

HP

Modifications
Pricing

1750

Dim. Pg.

Accessories &
Modifications

Frame ➃

Outline
Dimensions

Basic List Price*
GO-2A

Application
Information

Rated T op
Speed RPM

Other

1

Base
Speed RPM

Terms

HP

General
Information

Type CD
Shunt Wound

2.7

Dripproof Fully Guarded Motors

Self-Ventilated and
Separately Ventilated

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

PRICES - 240 and 500 Volts
Self Ventilated [DPFG]
Suitable for constant torque to 60% of base speed

10

Modifications
Pricing

Motor Pricing

HP

20

25

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

15

30

Terms

Type CD
Shunt Wound

Base
Speed RPM

Rated Top
Speed RPM

Basic List Price*
GO-2A

3500
2500
1750
1500
1150

3500
3000
2300
2100
2000

850
650
500
400
300
250
3500
2500
1750
1500
1150
850
650
500
400
300
250
3500
2500
1750
1500
1150
850
650
500
400
300
250
3500
2500
1750
1500
1150
850
650
500
400
300
250
3500
2500
1750
1500
1150
850
650
500
400
300
250

1700
1600
1500
1200
900
750
3500
3000
2300
2100
2000
1700
1600
1500
1200
900
750
3500
3000
2300
2100
2000
1700
1600
1500
1200
900
750
3500
3000
2300
2100
2000
1700
1600
1500
1200
900
750
3500
3000
2300
2100
2000
1700
1600
1500
1200
900
750

Frame ➃
240V

500V

$5652
$5788
$6874
$7442
$8358

218AT
218AT
219AT •

10

258AT

218AT
219AT •
258AT
258AT

$10988
$13514
$16004
$19706
$24742

287AT
327AT
365AT
366AT
368AT

287AT
327AT
365AT
366AT
407AT

$6894
$7020
$8332
$9078
$11272
$13442
$16708
$20928
$25324
$31092

218AT
219AT
258AT •
288AT
327AT
365AT
368AT
407AT
409AT

218AT
219AT
258AT •
259AT
288AT
327AT
365AT
368AT
407AT
409AT

$8178
$8088
$9600

219AT
258AT
259AT •

219AT
258AT
259AT •

$13098
$16068
$19898
$24734
$30074
$37828

327AT
365AT
366AT
368AT
407AT
504AT

327AT•
365AT
366AT
407AT
407AT
508AT

$9114
$8974
$11926

258AT
258AT
287AT •

258AT
259AT
287AT •

$15074
$18340
$23832
$28350
$34374
$40936

328AT
365AT
368AT
407AT
409AT
504AT

328AT
366AT
368AT
409AT
409AT
508AT

$10420
$9864
$13158

287AT
287AT
288AT •

259AT
259AT
288AT •

$16678
$20390
$26238
$31454
$37860
$46276

365AT
366AT
407AT
407AT
504AT
506AT

365AT
366AT
407AT
409AT
506AT
508AT

10

10

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.

2.8

www.gemotors.com

•

800-541-7191

Dim. Pg.

Separately Ventilated [DPFG-SV]
Suitable for constant torque to 5% of base speed
Basic List Price*
GO-2A

Frame ➃
240V

500V

$5652
$5788
$6874
$7442
$8358

218AT
218AT
219AT

218AT
218AT
219AT
258AT
258AT

$9990
$12286
$14550
$17916
$21516
$24166
$6894
$7020
$8332
$9078
$10248
$12220
$15190
$18198
$21952
$27036
$30546
$8178
$8088
$9600
$10454
$11908
$14608
$18090
$21508
$26152
$31642
$36496
$9114
$8974
$10842
$11660
$13704
$16674
$20724
$24652
$29890
$35596
$41896
$10420
$9864
$11962
$13012
$15162
$18538
$22816
$27352
$32922
$40240
$50400

287AT
327AT
328AT
329AT
366AT
366AT
218AT
219AT
258AT

10

258AT

10

288AT
327AT
327AT
328AT
366AT
366AT
368AT
219AT
258AT
259AT
10

327AT
328AT
328AT
329AT
366AT
407AT
407AT
258AT
258AT
287AT
10

328AT
328AT
329AT
366AT
368AT
409AT
409AT
287AT
287AT
288AT
10

328AT
329AT
366AT
368AT
407AT
409AT
409AT

Dim. Pg.

287AT
327AT
328AT
329AT
368AT
368AT
218AT
219AT
258AT
259AT
288AT
327AT
327AT
329AT
365AT
366AT
409AT
219AT
258AT
259AT
287AT
327AT •
328AT
328AT
329AT
366AT
407AT
10

258AT
259AT
287AT
288AT
328AT•
328AT
329AT
368AT
368AT
409AT
10

259AT
259AT
288AT •
327AT
328AT
329AT
366AT
407AT
407AT
409AT
10

➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable

for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

GEP387M 09/11 • Prices and data subject to change without notice.

Dripproof Fully Guarded Motors

Self-Ventilated and
Separately Ventilated

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

PRICES - 240 and 500 Volts

75

100

288AT
328AT •

$20774
$25386
$31050
$37474
$44662
$54908

366AT
368AT
409AT
504AT
506AT
508AT

366AT •
368AT •
407AT
504AT
506AT
508AT

10

$15088
$17788

327AT
365AT

288AT
328AT •

$23970
$29468
$35708
$42944
$51306

368AT
407AT
504AT
506AT
508AT

368AT •
407AT
409AT
506AT
508AT

$20406
$17608
$20406

10

10

365AT
366AT •

328AT
366AT •

$27434
$33490
$40210
$48652
$57536

407AT
L409AT
504AT
506AT
508AT

368AT •
407AT
504AT
506AT
508AT

$24538
$22450
$24028

10

366AT •

365AT
366AT •

$32310
$38482
$46966
$56104

L407AT
504AT
506AT
508AT

407AT
504AT
506AT
508AT

$30222
$30222

10

368AT

366AT
368AT •

$39558
$46420
$56282

L409AT
504AT
508AT

409AT
506AT
508AT

10

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.

www.gemotors.com

•

800-541-7191

$12004
$11526
$14122
$15598
$18064
$22074
$27000
$32586
$38836
$47746
$56926
$15300
$13716
$16170
$17952
$20844
$25624
$31050
$37342
$44614
$54420
$65250
$18550
$16008
$18550
$20138
$23856
$29122
$34966
$42306
$50032
$60778
$71460
$22308
$20410
$21844
$23176
$28096
$33462
$40840
$48786
$57480
$71586
$79800
$27474
$27474
$29050
$34398
$40366
$48940
$58032
$70398
$84600
$93630

10

10

287AT
328AT
327AT
328AT
366AT
368AT
409AT
407AT
506AT
506AT

288AT
327AT •
328AT
328AT •
366AT
368AT
407AT
409AT
409AT
10

10

10

327AT
328AT
328AT
329AT
368AT
407AT
409AT
506AT
506AT
508AT

288AT
328AT •
329AT
366AT •
368AT
407AT
504AT
409AT
508AT
508AT

10

10

365AT
366AT

328AT
L328AT •
366AT
368AT •
368AT
407AT
504AT
506AT
506AT
508AT

368AT
368AT
409AT
409AT
506AT
508AT
508AT
10

10

365AT
366AT

329AT
329AT•
366AT
368AT•
407AT
504AT
506AT
506AT
508AT

368AT
407AT
409AT
506AT
506AT
508AT
5010AY
366AT
368AT
10

L407AT
L409AT
506AT
506AT
508AT
5010AY
5010AY

Motor Pricing

287AT
287AT
328AT

Modifications
Pricing

$12004
$12678
$15534

Accessories &
Modifications

3500
3000
2100
2000
2000
1700
1600
1500
1200
900
750
3500
2700
2100
2000
2000
1700
1600
1500
1200
900
750
3500
2700
2100
2000
2000
1700
1600
1500
1200
900
750
3500
2700
2100
2000
2000
1700
1600
1500
1200
900
750
2700
2000
2000
2000
1700
1600
1500
1200
900
750

Outline
Dimensions

60

3500
2500
1750
1500
1150
850
650
500
400
300
250
3500
2500
1750
1500
1150
850
650
500
400
300
250
3500
2500
1750
1500
1150
850
650
500
400
300
250
3500
2500
1750
1500
1150
850
350
500
400
300
250
2500
1750
1500
1150
850
650
500
400
300
250

Application
Information

50

Rated Top
Speed RPM

10

366AT
368AT •
368AT
407AT •
409AT
506AT
508AT
5010AY
5010AY
6062

Other

40

Base
Speed RPM

Separately Ventilated [DPFG-SV]
Suitable for constant torque to 5% of base speed
Frame ➃
Basic List Price*
GO-2A
240V
500V
Dim. Pg.

Terms

HP

Self Ventilated [DPFG]
Suitable for constant torque to 60% of base speed
Frame ➃
Basic List Price*
GO-2A
240V
500V
Dim. Pg.

➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable

for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

GEP387M 09/11 • Prices and data subject to change without notice.

General
Information

Type CD
Shunt Wound

2.9

Dripproof Fully Guarded Motors

Self-Ventilated and
Separately Ventilated

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

PRICES - 240 and 500 Volts

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

HP

125

150

200

250

Base
Speed RPM

Rated Top
Speed RPM

2500
1750
1500
1150
850
650
500
400
300
250
2500
1750
1500
1150
850
650
500
400

2700
2000
2000
2000
1700
1600
1500
1200
900
750
2700
2000
2000
2000
1700
1600
1500
1200

300

900

1750
1500
1150
850
650
500
400

2000
1900
1800
1700
1600
1500
1200

300

900

1750
1500
1150
850
650
500
400
300

1900
1800
1700
1600
1600
1500
1200
900

Self Ventilated [DPFG]
Suitable for constant torque to 60% of base speed
Frame ➃
Basic List Price*
GO-2A
240V
500V
Dim. Pg.
$35848
$35848

L407AT

368AT
407AT •

$46420
$54400

504AT
506AT

506AT
508AT

$43192
$43192

10

L409AT

407AT
409AT

$53424
$61590

506AT
508AT

506AT
508AT

$54866

504AT

504AT

$66198

L508AT

508AT

$67534

L506AT

506AT

10

Separately Ventilated [DPFG-SV]
Suitable for constant torque to 5% of base speed
Frame ➃
Basic List Price*
GO-2A
240V
500V
Dim. Pg.
$32590
$32590
$34960
$40366
$47304
$56364
$69264
$80700
$95632
$106624
$37558
$37558
$40672
$46456
$53556
$63466
$78234
$88812

L407AT
L407AT
10

L409AT
504AT
506AT
508AT
5010AY
5010AY
6160
L407AT
L407AT
10

L409AT
506AT
506AT
5010AY
5010AY

368AT
368AT •
407AT
409AT •
506AT
506AT
508AT
5010AY
5010AY
6062
407AT
407AT
409AT
409AT
506AT
506AT
508AT
5010AY

$106624

6062

6062

$47710
$51640
$57564
$65652
$77992
$92718
$106782

L409AT

L409AT
L409AT
506AT
506AT
508AT
6062
6157

10

506AT
508AT
5010AY
6058
6058

$126330

6160

6164

$58726
$62148
$69190
$78130
$88426
$110914
$124290
$145464

L504AT

504AT
506AT
506AT
5010AY
5010AY
6062
6169
6259

10

L508AT
6052
6058
6062
6160
6164

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

Terms

Other

Application
Information

Type CD
Shunt Wound

Dripproof Fully Guarded Separately-Ventilated (DPFG-SV)
(Frame CD506AT shown above.)

2.10

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Dripproof Fully Guarded Motors

Separately Ventilated

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

PRICES - 500 Volts

500

600

Frame ➃

1750
1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400

1900
1800
1600
1500
1500
1300
1200
900
1900
1800
1500
1500
1400
1200
1000
750
1900
1700
1500
1400
1200
1000
1000

$70470
$74906
$81204
$91126
$100846
$121416
$139644
$163024
$98010
$104280
$107730
$117450
$126090
$141840
$166372
$200410
$131130
$134786
$138040
$146814
$153288
$166686
$200544

506AT •
506AT
508AT •
5010AY •
6062
6160
6169
6262
508AT •
5010AY
5010AY •
6062
6160
6259
6262
6266
5010AY •
6055
6058
6160
6164
6262
6266

300
1750
1500
1150
850
650
500
400

750
1900
1700
1500
1300
1200
1000
1000

$228456
$181576
$188510
$201664
$203616
$222928
$248968
$266634

6271
6063
6063
6066
6173
6268
6275
6280

300

750

$290842

6881

500V

Dim. Pg.

HP

700

800

900

1000

1250

Rated Top
Speed
RPM

Basic
List Price*
GO-2A

Frame ➃

1750
1500
1150
850
650
500
400
300
1750
1150
850
650
500
400
300
1150
850
650
500
400
300
1150
850
650
500
400
300
250
1150
850
650
500
400
300

1800
1700
1300
1200
1000
1000
1000
750
1750
1250
1000
1000
1000
1000
750
1250
1000
1000
1000
1000
750
1250
1000
1000
1000
1000
750
710
1150
1000
1000
1000
900
750

$206786
$216564
$224164
$226248
$251260
$273780
$291438
$326238
$242216
$247248
$249630
$275346
$296988
$317656
$355582
$276126
$278298
$298690
$318642
$339120
$379612
$299808
$301686
$320878
$342954
$363186
$406548
$462600
$358344
$360222
$379944
$399922
$423514
$474082

6165

500V

Dim. Pg.

10

6168
6173
6270
6275
6881
6887
10

6173
6270
6275
6280
6881
6887
6268
6270
6275
6779
6887
6985
6268
6270
6774
6881
6887
6985
6991
6776
6778
6785
6896
6996
10

Terms

Other

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

Base
Speed
RPM

Modifications
Pricing

400

Basic
List Price*
GO-2A

Accessories &
Modifications

300

Rated Top
Speed
RPM

Outline
Dimensions

HP

Base
Speed
RPM

Separately Ventilated [DPFG-SV]
Suitable for constant torque to
5% of base speed

Application
Information

Separately Ventilated [DPFG-SV]
Suitable for constant torque to
5% of base speed

Motor Pricing

General
Information

Type CD
Shunt Wound

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2.11

Dripproof Fully Guarded Motors

Separately Ventilated

Modifications
Pricing

Motor Pricing

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

PRICES - 600V
Separately Ventilated [DPFG-SV]
Suitable for constant torque to
5% of base speed

HP

25

30

Application
Information

Outline
Dimensions

Accessories &
Modifications

40

50

60

75

Base
Speed
RPM

Rated T op
Speed
RPM

Basic
List Price*
GO-2A

Frame ➃

1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400

1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400

$10842
$13704
$16674
$20724
$24652
$29890
$11962
$15162
$18538
$22816
$27352
$32922
$14122
$18064
$22074
$27000
$32586
$38836
$16170
$20844
$25624
$31050
$37342
$44614
$18550
$23856
$29122
$34966
$42306
$50032
$21844
$28096
$33462
$40840
$48786
$57480

287AT
327AT
328AT

600V

Separately Ventilated [DPFG-SV]
Suitable for constant torque to
5% of base speed

Dim. Pg.

HP

100

10
10
10

288AT
328AT
329AT

125

10
10
10

327AT
329AT
368AT

150

10
10
10

328AT
329AT
368AT

200

10
10
10

L328AT
368AT
407AT

250

10
10
10

329AT
368AT
409AT

300

10
10
10

Base
Speed
RPM

Rated T op
Speed
RPM

Basic
List Price*
GO-2A

Frame ➃

1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400

1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400

$27474
$34398
$40366
$48940
$58032
$70398
$32590
$40366
$47304
$56364
$69264
$80700
$37558
$46456
$53556
$63466
$78234
$88812
$47710
$57564
$65652
$77992
$92718
$106782
$58726
$69190
$78130
$88426
$110914
$124290
$70470
$81204
$91126
$100846
$121416
$139644

368AT
407AT
409AT

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

Terms

Other

Type CD
Shunt Wound

2.12

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

600V

10
10
10

407AT
409AT
506AT
10
10
10

409AT
409AT
506AT
10
10
10

409AT
506AT
508AT
10
10

6062
504AT
508AT
5010AY
10

6062
6160
506AT
5010AY
10

6062
6160
6164

Dim. Pg.

Dripproof Fully Guarded Motors

Separately Ventilated

Class F Insulation
For Continuous Operation in 40°C Ambient

PRICES - 600V (Type C Power Supply)➁

800

900

1000

1250

1500

1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1150
850
650
500
400
1150
850
650
500
400
1150
850
650
500
400
1150
850
650
500
400
850
650
500
400

$98010
$107730
$117450
$126090
$141840
$166372
$131130
$138040
$146814
$153288
$166686
$200544
$181576
$201664
$203616
$222928
$248968
$266634
$224164
$226248
$251260
$273780
$291438
$247248
$249630
$275346
$296988
$317656
$276126
$278298
$298690
$318642
$339120
$299808
$301686
$320878
$342954
$363186
$360222
$379944
$399922
$423514

508AT
5010AY
6062
6160
6164
6169
6055
6058
6160
6164
6262
6266
6058
6062
6164
6169
6266
6271
6173
6268
6270
6275
6280
6268
6270
6275
6280
6881
6268
6270
6275
6881
6887
6268
6270
6275
6881
6887
6774
6779
6887
6985

1150

1150

$413182

6876

850
650
500
400

850
650
500
400

$413182
$436060
$459172
$486262

6881
6887
6996
6999

Dim.
Pg.

HP

1750
2000
2250
2500
3000

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

850
650
500
850
650
500
850
650
850

850
650
500
850
650
500
850
650
850

$465400
$490894
$516912
$582880
$620200
$670020
$634466
$675090
$684470

6890
6996
6999
6896
6996
6999
6896
6999
6990

850

850

$780486

6996

600V

Dim.
Pg.

PRICES - 700V (3 Phase, 6 Controlled Pulse Power Supply)➁
Separately Ventilated [DPFG-SV]
Suitable for constant torque to
5% of base speed

HP

1500

1750

2000
2250
2500
3000

Frame ➃

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

700V

1150

1150

$413182

6873

850
650
500
450
400
350
850
650
500
450
400
850
650
500
850
650
500
850
650
850

1000
900
850
810
770
720
960
900
800
760
720
900
840
750
850
795
710
850
750
850

$413182
$436060
$459172
$472718
$486262
$527278
$465400
$490894
$516912
$641588
$675292
$582880
$620200
$670020
$634466
$675090
$729320
$684470
$728294
$780486

6876
6881
6981
6985
6985
6991
6881
6990
6996
6999
6999
6896
6996
6999
6896
6996
6999
6996
6999
6996

Base
Speed
RPM

Dim.
Pg.

Accessories &
Modifications

1750
1150
850
650
500
400
1750
1150
850
650
500
400
1750
1150
850
650
500
400
1150
850
650
500
400
1150
850
650
500
400
1150
850
650
500
400
1150
850
650
500
400
850
650
500
400

600V

Frame ➃

Base
Speed
RPM

Outline
Dimensions

700

Basic
List Price*
GO-2A

Application
Information

600

Rated
Top
Speed
RPM

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.

Other

500

Frame ➃

Base
Speed
RPM

Terms

400

Separately Ventilated [DPFG-SV]
Suitable for constant torque to
5% of base speed

Modifications
Pricing

Separately Ventilated [DPFG-SV]
Suitable for constant torque to
5% of base speed

Motor Pricing

PRICES - 600V (Type C Power Supply)➁

HP

General
Information

Type CD
Shunt Wound

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2.13

Totally Enclosed Motors

Nonventilated
Type CD
Shunt Wound

PRICES - 240 and 500 Volts
TENV
Suitable for constant torque to 5% of base speed

HP

1

1.5

TENV
Suitable for constant torque to 5% of base speed

Frame ➃

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

240V

500V

1750
1150
850
650
500
400
300
3500
2500
1750
1150
850
650
500
400

2300
2000
1750
1600
1500
1200
900
3500
3000
2300
2000
1700
1600
1500
1200

$3836
$4132
$3958
$6822
$7930
$9096
$9978
$3006
$3088
$3394
$4472
$6360
$7732
$8928
$10458

L182AT •
L182AT •
186AT
218AT
219AT
219AT
219AT
L182AT
L182AT
186AT
L186AT
189AT
219AT
258AT
258AT

186AT

Dim.
Pg.

HP

10
10
10

2

10
10
10
10
10

186AT
10
10
10

3

10
10

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

Frame ➃

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

240V

500V

3500
2500
1750
1150
850
650
500
400
300
3500
2500
1750
1150
850
650
500
400
300

3500
3000
2300
2000
1700
1600
1500
1200
900
3850
3000
2300
2000
1700
1600
1500
1200
900

$3358
$3710
$4076
$5446
$7008
$8334
$9978
$11670
$14478
$4074
$4520
$5308
$7360
$8350
$9856
$11890
$14982
$17718

186AT
186AT
L186AT
189AT
219AT
2110AT
258AT
259AT
327AT
L186AT
L186AT
L186AT
219AT
2110AT
259AT
288AT
288AT
328AT

186AT
186AT
L186AT
189AT •
219AT
2110AT
258AT
259AT
327AT
L186AT
L186AT
L186AT
219AT
2110AT
259AT

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

2.14

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

10
10
10

Dim.
Pg.

Totally Enclosed Motors

Nonventilated, Fan Cooled,
Air-Over-Frame

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

General
Information

Type CD
Shunt Wound

PRICES - 240 and 500 Volts

10

15

20

Basic
List Price*
GO-2A

240V

3500

3500

$6110

219AT

10

$6341

186AT

10

2500
1750
1500
1150
850
650
500
400
300

3000
2300
2100
2000
1700
1600
1500
1200
900

$7108
$8664

219AT
2110AT

219AT
2110AT •

L186AT
189AT •

L186AT
189AT •
218AT

$10504
$13552
$16120
$19104

258AT
287AT
288AT
327AT

258AT
287AT

$7027
$8174
$9175
$10079
$12080
$15585
$18538
$21970
$26165

3500

3500

$8452

2110AT

10

$8298

L186AT

10

2500
1750
1500
1150
850
650
500
400
300
3500
2500
1750

3000
2300
2100
2000
1700
1600
1500
1200
900
3500
3000
2300

$8664
$10582

2110AT
259AT

2110AT
259AT •

189AT
2110AT •

$13452
$16270
$19456

288AT
327AT
365AT

288AT

$9720
$9964
$11056
$12169
$15470
$18711
$22374
$27418
$32745
$10854
$11144
$11403

189AT
2110AT •
258AT
259AT
288AT
328AT
366AT

1500

2100

$13119

10

287AT

1150
850
650
500
400
3500

2000
1700
1600
1500
1200
3500

$14902
$17802
$21898
$25928
$31761
$13156

288AT
327AT
365AT
368AT
407AT
258AT

288AT
327AT
365AT

2500

3000

$13496

259AT

1750
1500
1150
850
650
500
400
3500
2500
1750
1500
1150
850
650
500

2300
2100
2000
1700
1600
1500
1200
3500
3000
2300
2100
2000
1700
1600
1500

$14849
$16733
$18264
$21776
$28170
$33741
$40696
$16256
$16675
$17110
$19884
$21218
$27076
$33534
$39868

288AT •

$12958
$15480
$19042
$22546

327AT
328AT
366AT
10

10

10
10

327AT
10

366AT
368AT

$14982

328AT

328AT

$18936
$24496
$29340

368AT
407AT
407AT

366AT
368AT
407AT

$18450

366AT

366AT

$23544

10

368AT

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating

www.gemotors.com

•

800-541-7191

240V

10

240V

500V

$13858
$17270
$19838
$22822
$26470

259AT
288AT
327AT
365AT
368AT

259AT

366AT
409AT

$13936
$17170
$19988
$23174
$27560
$32594

259AT
288AT
328AT
365AT
368AT
407AT

259AT
288AT
328AT
365AT
368AT
409AT

$13290

259AT

259AT

288AT
327AT
365AT
368AT
407AT

288AT
327AT
365AT
368AT
407AT

10

$16312
$19198
$22760
$26264
$31738
$14794

10

10

259AT

$15090

10

10

288AT •
288AT
328AT
365AT
368AT
407AT
409AT

$16266

288AT

288AT

$19600
$22654
$28616
$33406
$39508
$17854
$18218
$18596

328AT
365AT
368AT
407AT
409AT

328AT
365AT
358AT
407AT
409AT

10

10

$22168
$27262
$33280
$38788

500V

Dim.
Pg.

Dim.
Pg.

10

259AT
288AT

259AT
10
10

365AT

10
10

10

259AT
288AT
328AT
365AT
368AT
407AT
219AT
2110AT
259AT •

328AT
365AT
368AT
407AT
409AT
287AT
288AT
327AT •
10

366AT
368AT
407AT
409AT

10
10

10

Modifications
Pricing

10

Dim.
Pg.

Basic
List Price*
GO-2A

10

Accessories &
Modifications

500V

Basic
List Price*
GO-2A

10

2110AT
259AT •

10

288AT
327AT
327AT
366AT
368AT
407AT
409AT

10

10

327AT

327AT

366AT
358AT
407AT
409AT

366AT
368AT
407AT
409AT

➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable

for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

GEP387M 09/11 • Prices and data subject to change without notice.

Motor Pricing

Frame ➃

Rated
Top
Speed
RPM

Outline
Dimensions

7.5

Frame ➃

Base
Speed
RPM

Application
Information

5

Frame ➃

TEAO
Suitable for constant torque to
40% of base speed

Other

HP

TEFC
Suitable for constant torque to
60% of base speed

2.15

Terms

TENV
Suitable for constant torque to
5% of base speed

Totally Enclosed Motors

Nonventilated, Fan Cooled,
Air-Over-Frame, Unit Cooled
Type CD
Shunt Wound

PRICES - 240 and 500 Volts
TENV
Suitable for constant torque to
5% of base speed

HP

25

30

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

Rated
Top
Speed
RPM

2500

3000

1750
1500
1150
850
650
500
400
300
2500
1750
1500
1150
850
650
500
400
300
2500
1750
1500
1150
850

2300
2100
2000
1700
1600
1500
1200
900
3000
2300
2100
2000
1700
1600
1500
1200
900
3000
2300
2100
2000
1700

650

1600

500
400
300

1500
1200
900

Frame ➃

Frame ➃

Basic List
Price*
GO-2A

240V

500V

$22150

368AT

368AT

$26880

409AT

407AT

$29066

10

TEAO
Suitable for constant torque to
40% of base speed

409AT

Dim.
Pg.

Basic List
Price*
GO-2A

240V

500V

Frame ➃
Dim.
Pg.

Basic List
Price*
GO-2A

240V

500V

$18837

327AT

327AT

$20098

327AT

327AT

$20097
$21813
$25473
$30912
$38426

328AT •

328AT
328AT
368AT
407AT
409AT

$21194

328AT

328AT

$25868
$31000
$37534

368AT
407AT
409AT

368AT
407AT
409AT

$18082
$19378
$22054
$24442
$29878

$25530
$28212
$30139
$33490
$40924

10

368AT
407AT
409AT

365AT
366AT •
10

407AT
409AT

366AT
368AT •
10

407AT
409AT

365AT
366AT •
365AT
368AT
409AT

366AT
368AT •
366AT
407AT
409AT

TEAAC
Suitable for constant torque to
5% of base speed

$21800
$23096

365AT
366AT

365AT
366AT

$28562
$33998
$40900

407AT
409AT
10

368AT
409AT
409AT

$25918
$28652

366AT
368AT

366AT
368AT

$33242
$39706

407AT
409AT

407AT
409AT

$45700

504AT

504AT

Frame ➃
Dim.
Pg.

Basic List
Price*
GO-2A

240V

500V

$50438
$57560
$68454

368AT
407AT
409AT

368AT
407AT
409AT

$41346
$55858
$63746
$75674

368AT
368AT
409AT
409AT

368AT
407AT
409AT
508AT

$49848

368AT

368AT

$65624
$74890
$88646

409AT
409AT
506AT

409AT
506AT
508AT

Terms

Other

Application
Information

Outline
Dimensions

40

Base
Speed
RPM

TEFC
Suitable for constant torque to
60% of base speed

Totally Enclosed Nonventilated (TENV)
(Frame CD328AT shown above.)

Totally Enclosed Fan Cooled (TEFC)
(Frame CD366AT shown above.)

* Basic list price applies to frames listed. It does not include pricing for
modifications or accessories. Refer to Modifications section for appropriate
list price addition(s).
• Standard rating

➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suit-

2.16

www.gemotors.com

•

800-541-7191

able for belt drive or direct coupling (within limits given in Application
Section). Frames CD6200, CD6700, CD6800, and CD6900 are suitable for
direct drive only.
10 Refer to GE for frame.

GEP387M 09/11 • Prices and data subject to change without notice.

Dim.
Pg.

Totally Enclosed Motors

Fan Cooled, Air-Over-Frame,
Unit Cooled

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

General
Information

Type CD
Shunt Wound

PRICES - 240 and 500 Volts

75

100

Basic
List Price*
GO-2A

240V

500V

1750

2100

$34031

409AT

409AT •

1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400

2000
2000
1700
1600
1500
1200
900
2100
2000
2000
1700
1600
1500
1200
900
2100
2000
2000
1700
1600
1500
1200

$34456
$38638

10

10

L409AT

409AT

300

900

1750
1500
1150
850
650
500
400

2000
2000
2000
1700
1600
1500
1200

300

900

$37051
$38440

$41283
$43948

409AT
10

409AT
10

409AT •
409AT

409AT
409AT

Dim.
Pg.

Frame ➃

Basic
List Price*
GO-2A

240V

500V

$33712

409AT

409AT

$37718
$43070
$51150

L409AT
504AT
506AT

409AT
405AT
506AT

$36338

L409AT

409AT

$41336
$47964
$56736

504AT
506AT
508AT

504AT
506AT
508AT

$40018

L409AT

409AT

$45700
$54432

504AT
10

504AT
506AT

$45880

506AT

506AT

$55830
$62810

10

508AT

10

10

Dim.
Pg.

Basic
List Price*
GO-2A

240V

$34210

500V

Dim.
Pg.

366AT

$44336
$57630
$74358
$84858
$100222
$37680

368AT
409AT
409AT
506AT
506AT

368AT
4007AT
504AT
506AT
508AT
366AT

$40936
$50740
$64880
$82352
$93980
$106758
$42412

368AT
407AT
504AT
504AT
506AT
508AT

368AT
407AT
409AT
504AT
506AT
508AT
366AT

$49046
$59850
$75008
$93312
$106448

L407AT
L409AT
504AT
506AT
508AT

407AT
409AT
504AT
506AT
508AT

$125260

6052

6058

$49454
$55728
$61916
$74050
$90424
$109624
$125104

L407AT
L407AT
504AT
506AT
508AT
6055

407AT
407AT
407AT
409AT
506AT
508AT
5010AY

$146734

6058

6058

Motor Pricing

Rated
Top
Speed
RPM

Modifications
Pricing

60

Frame ➃

Base
Speed
RPM

Accessories &
Modifications

50

Frame ➃

TEAAC
Suitable for constant torque to
5% of base speed

Outline
Dimensions

HP

TEAO
Suitable for constant torque to
40% of base speed

Application
Information

TEFC
Suitable for constant torque to
60% of base speed

Terms

Other

* Basic list price applies to frames listed. It does not include pricing for modifications or
accessories. Refer to Modifications section for appropriate list price addition(s).
• Standard rating
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

Totally Enclosed Air-Over-Frame (TEAO)
(Frame CDL506AT shown above.)

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2.17

Totally Enclosed Motors

Unit Cooled
Type CD
Shunt Wound

PRICES - 500 Volts
TEAAC
Suitable for constant torque to
5% of base speed

HP

125

150

Base
Speed
RPM

Rated T op
Speed
RPM

Basic
List Price*
GO-2A

Frame ➃

1750
1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400
300

2000
2000
2000
1700
1600
1500
1200
900
2000
2000
2000
1700
1600
1500
1200
900

$58594
$66322
$74182
$87346
$104546
$124216
$141756
$165894
$67302
$76458
$85988
$99962
$117698
$137568
$156994
$183392

407AT
409AT
504AT
506AT 21
506AT 21
508AT 21
5010AY
6058
504AT 21
504AT 21
504AT 21
508AT 21
508AT 21
5010AY
6058
6062

500V

TEAAC
Suitable for constant torque to
5% of base speed

Dim. Pg.

HP

200

250

Base
Speed
RPM

Rated T op
Speed
RPM

Basic
List Price*
GO-2A

Frame ➃

1750
1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400
300

2000
2000
2000
1700
1600
1500
1200
900
2000
2000
2000
1700
1600
1500
1200
900

$83750
$95692
$108552
$123676
$141900
$161614
$184436
$214830
$106394
$118590
$130058
$145882
$164048
$183126
$208986
$242882

504AT 21
506AT 21
506AT 21
508AT
5010AY
6062
6157
6164
506AT 21
508AT 21
508AT 21
5010AY
5010AY
6062
6169
6259

500V

Dim. Pg.

* Basic list price applies to frames listed. It does not
include pricing for modifications or accessories. Refer to
Modifications section for appropriate list price addition(s).
➁ For suitability of operation with rectified power supplies,
see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000,
and CD6100 is suitable for belt drive or direct coupling
(within limits given in Application Section). Frames CD6200,
CD6700, CD6800, and CD6900 are suitable for direct
drive only.
21 Totally enclosed Air-to-Air cooled machine provided in “B”
size cooler.

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

Totally Enclosed Air-To-Air Cooled
(Frame CD6774 shown above.)

Terms

Other

Totally Enclosed Air-To-Air Cooled (TEAAC)
(Frame CD506AT shown above.)

2.18

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Totally Enclosed Motors

Unit Cooled

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

General
Information

Type CD
Shunt Wound

PRICES - 500 and 700 Volts

500

600

700

1750

1900

$129550

506

1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400
300
1750
1500
1150
850
650
500
400
300

1800
1600
1500
1600
1300
1200
900
1900
1800
1500
1500
1400
1200
1000
750
1900
1700
1500
1400
1200
1000
1000
750
1900
1700
1500
1300
1200
1000
1000
750
1800
1600
1300
1200
1000
1000
1000
750

$140758
$150754
$166954
$184690
$202812
$231450
$268502
$176754
$184466
$190314
$206562
$222664
$238264
$271908
$314530
$224922
$227516
$228018
$243648
$257420
$269978
$308100
$355602
$280788
$283900
$287014
$305424
$334392
$373452
$406224
$440312
$313748
$316736
$319718
$338134
$367928
$407750
$442850
$480010

508 21
5010AY
5010AY
6062
6160
6169
6262
5010AY
5010AY
5010AY
6062
6160
6259
6262
6266
6055
6058
6058
6160
6164
6262
6266
6271
6063
6063
6063
6173
6268
6275
6280
6881
6165

Frame ➃

Frame ➃
500V

Dim. Pg.

700V

Dim. Pg.

Basic
List Price*
GO-2A

Frame ➃
500V

Frame ➃
Dim. Pg.

700V

Dim. Pg.

21

6062
6164
6169
6262
6266
6271

6160
6169
6262
6266
6271
6887

10

6268
6268
6270
6280
6881
6887

6160
6259
6262
6266
6779
6887

6062
6160
6169
6262

Modifications
Pricing

$136864
$149210
$171898
$206726
$232074
$144764
$150668
$156216
$172282
$183022
$200786
$240776
$269522
$183394
$186662
$189686
$205952
$214442
$226500
$271004
$302682
$239134
$245142
$251152
$264882
$281404
$308170
$333292
$363532
$269272
$274764
$280632
$295064
$313468
$342226
$368418
$402464

10
10
10

6062
6160
6259
6262
6266
6055
6058
6058
6160
6164
6262
6266
6271
6063
6063
6066
6173
6268
6275
6280
6881
6165
6165
6168
6173
6270
6275
6881
6887

Accessories &
Modifications

400

Basic
List Price*
GO-2A

6062
6164
6169
6262
6266
6271

Outline
Dimensions

300

Rated
Top
Speed
RPM

6062
6169
6262
6266
6271
6887

Application
Information

HP

Base
Speed
RPM

TEWAC
Suitable for constant torque to
5% of base speed

Motor Pricing

TEAAC
Suitable for constant torque to
5% of base speed

6160
6259
6262
6266
6779
6887

Terms

Other

* Basic list price applies to frames listed. It does not include pricing for modifications or accessories. Refer to Modifications
section for appropriate list price addition(s).
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable for belt drive or direct coupling (within
limits given in Application Section). Frames CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.
21 Totally enclosed Air-to-Air cooled machine provided in “B” size cooler.

Totally Enclosed Air-To-Air Cooled
(Frame CD6160 shown above.)

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2.19

Totally Enclosed Motors

Unit Cooled

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

PRICES - 500 and 700 Volts
TEAAC
Suitable for constant torque to
5% of base speed

HP

800

900

1000

1250

1500

1750
2000

2250
3000

TEWAC
Suitable for constant torque to
5% of base speed

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

1150

1250

$351042

6268

6268

$308954

6268

6268

850
650
500
400
300
1150
850
650
500
400
300
1150
850
650
500
400
300
1150
850
650
500
400
850
650
500
400
850
650
500
850
650
500
850
650
500
850
650
850

1200
1000
1000
1000
750
1250
1000
1000
1000
1000
750
1250
1000
1000
1000
1000
750
1150
1000
1000
1000
1000
900
900
850
770
900
900
800
900
840
750
850
795
710
850
750
850

$369286
$399686
$439998
$477234
$517280
$381212
$399138
$429964
$470552
$509772
$552550
$410390
$427882
$458988
$499676
$540756
$586132
$479772
$495774
$527092
$567450
$612732
$559170
$590172
$629594
$678598
$619054
$649360
$687416
$757744
$806260
$871026
$818998
$867340
$931512
$877976
$925890
$990246

6270
6275
6779
6881
6887
6268
6270
6774
6779
6887
6985
6270
6275
6774
6881
6887
6985
6776
6778
6785
6896
6996

6270
6275
6280
6881
6887
6268
6270
6275
6779
6881
6985
6268
6275
6779
6881
6887
6985

$323974
$344182
$374756
$401824
$439544
$336296
$351816
$373762
$406004
$433794
$475076
$362800
$378744
$402370
$436160
$464544
$509288
$426032
$442776
$470394
$507628
$537054
$503050
$534428
$574630
$604624
$560368
$595322
$638134
$699456
$744240
$804024
$759568
$808202
$871070
$817706
$870062
$929018

6270
6275
6779
6881
6887
6268
6270
6774
6779
6887
6985
6270
6275
6774
6881
6887
6985
6776
6778
6785
6896
6996

6270
6275
6280
6881
6887
6268
6270
6275
6779
6881
6985
6268
6275
6779
6881
6887
6985

Frame ➃

Frame ➃
500V

Dim. Pg.

700V

6977
6977
6981
6985
6881
6887
10
10

6881
6990
6996
6896
6996
6999
6896
6996
6999
6996
6999
6999

Dim. Pg.

Basic
List Price*
GO-2A

Frame ➃
500V

Frame ➃
Dim. Pg.

700V

Dim. Pg.

6977
6977
6981
6985
6881
6887
10
10

6881
6990
6996
6896
6996
6999
6896
6996
6999
6996
6999
6999

* Basic list price applies to frames listed. It does not include pricing for modifications or accessories. Refer to Modifications section
for appropriate list price addition(s).
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable for belt drive or direct coupling (within limits
given in Application Section). Frames CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.

Terms

Other

Type CD
Shunt Wound

Totally Enclosed Water-To-Air Cooled
(Frame CD6160 shown above.)

2.20

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Totally Enclosed 30 Minute Rating Motors

Nonventilated

14

Class F Insulation
Type C Power Supply➁
For Operation in 40°C Ambient

PRICES - 240 and 500 Volts

7.5

10

15

20

25

30

500V

240V

500V

1750
1150
850
1750
1150
850
1750
1150
850
1750
1150
850
650
1750
1150

2300
2000
1700
2300
2000
1700
2300
2000
1700
2300
2000
1700
1600
2300
2000

$2198
$2476
$3202
$2468
$2882
$4300
$2726
$3346
$4848
$3304
$4740
$5778
$6820
$4914
$6064

L182AT
L182AT
186AT
L182AT
L182AT
186AT
L182AT
L186AT
189AT
186AT
189AT
219AT
2110AT
L186AT
219AT

10

1750
1150
850
650
1750
1150
850
650
1750
1150
850
650
1750
1150
850

2100
2000
1700
1600
2100
2000
1700
1600
2100
2000
1700
1600
2100
2000
1700

$14122
$18064
$22074
$27000
$16170
$20844
$25624
$31050
$18550
$23856
$29122
$34966
$21844
$28096
$33462

365AT
366AT
366AT
407AT
365AT
366AT
368AT
407AT
366AT
368AT
407AT
409AT
366AT
407AT
L409AT

365AT
365AT
366AT
368AT
365AT
366AT
368AT
407AT
366AT
368AT
407AT
409AT
366AT
407AT
409AT

850
650
1750
1150
850
650
1750
1150

1700
1600
2300
2000
1700
1600
2300
2000

$7264
$8746
$5994
$7318
$8682
$10500
$6874
$8358

2110AT
259AT
2110AT
258AT
259AT
288AT
2110AT
259AT

650
1750
1150
850
650
1750
1150
850

1600
2000
2000
1700
1600
2000
2000
1700

$40840
$27474
$34398
$40366
$48940
$32590
$40366
$47304

504AT
368AT
L407AT
504AT
506AT
L407AT
L409AT
506AT

409AT
368AT
407AT
409AT
506AT
407AT
409AT
506AT

2110AT
259AT

850

1700

$9990

288AT

650
1750
1150
850
650
1750
1150
850
650
1750
1150
850
650
1750
1150
850
650

1600
2300
2000
1700
1600
2300
2000
1700
1600
2300
2000
1700
1600
2300
2000
1700
1600

$12286
$8332
$10248
$12220
$15190
$9600
$11908
$14608
$18090
$10842
$13704
$16674
$20724
$11962
$15162
$18538
$22816

328AT
259AT
288AT
327AT
365AT
288AT
328AT
365AT
365AT
327AT
365AT
365AT
366AT
328AT
365AT
366AT
368AT

288AT

650

1600

$56364

508AT

508AT

328AT
259AT
288AT
327AT
365AT
288AT
328AT
365AT
365AT
327AT
365AT
365AT
366AT
328AT
365AT
366AT
368AT

1750
1150
850
650
1750
1150
850
1750
1150
1750
1150
1750

2000
2000
1700
1600
2000
1800
1700
1900
1700
1900
1600
1900

$37558
$46456
$53556
$63466
$47710
$57564
$65652
$58726
$69190
$70470
$81204
$98010

L409AT
504AT
506AT
508AT
504AT
506AT
508AT
L506AT
L508AT
L506AT
L508AT

409AT
506AT
508AT
508AT
504AT
506AT
508AT
506AT
508AT
506AT
508AT
508AT

10
10

Dim.
Pg.

HP

40

10
10
10
10

50

10
10
10
10

60

10
10
10
10

75

10
10

2110AT
258AT

100

10
10

125

150

200
250
300
400

10

Dim.
Pg.

Motor Pricing

240V

Frame ➃

Modifications
Pricing

5

Basic
List Price*
GO-2A

Accessories &
Modifications

3

Rated
Top
Speed
RPM

Outline
Dimensions

2

Base
Speed
RPM

Frame ➃

* Basic list price applies to frames listed. It does not include pricing for modifications
or accessories. Refer to Modifications section for appropriate list price addition(s).
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.
14 The NEMA definition for short time rated motors is as follows “All short time ratings
are based upon a corresponding short time load test, which shall commence only
when the windings and other parts of the machine are within 5°C of the ambient
temperature at the time of starting the test.” This means that field voltage should
be removed when the motor is not operating.
These short time rated motors have 150% occasionally repeated overload capability
at all speeds within the standard speed range. To add for wider than standard speed
range, use rated HP and the tables in page__ item __ (frame size may be different
from standard).

Application
Information

1.5

Basic
List Price*
GO-2A

Other

1

Rated
Top
Speed
RPM

Terms

HP

Base
Speed
RPM

General
Information

Type CD
Shunt Wound

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2.21

Totally Enclosed 60 Minute Rating Motors

Nonventilated

14

General
Information

Class F Insulation
Type C Power Supply➁
For Operation in 40°C Ambient

PRICES - 240 and 500 Volts

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

HP

1

1.5

2

3

5

7.5

10

15

20

25

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

240V

500V

Dim. Pg.

10

1750

2300

$15502

365AT

328AT

a

10

30

1150
850
650
1750

2000
1700
1600
2100

$19552
$23902
$29424
$19624

366AT
366AT
407AT
366AT

365AT
366AT
368AT
365AT

40

1150
850
650
1750

2000
1700
1600
2100

$23296
$28468
$33264
$23672

366AT
368AT
407AT
366AT

366AT
368AT
407AT
366AT

50

1150
850
650
1750
1150
850

2000
1700
1600
2100
2000
1700

$26878
$31160
$37256
$25774
$29772
$34712

368AT
407AT
409AT
368AT
407AT
504AT

368AT
407AT
409AT
366AT
407AT
409AT

10

650

1600

$41728

504AT

409AT

10

1750
1150
850
650
1750
1150
850

2100
2000
1700
1600
2000
2000
1700

$28718
$33264
$39886
$47728
$33408
$41004
$46588

368AT
L407AT
504AT
506AT
L407AT
409AT
506AT

368AT
407AT
504AT
506AT
407AT
409AT
506AT

650

1600

$56376

508AT

508AT

1750
1150
850
650
1750
1150
850
1750
1150

2000
2000
1700
1600
2000
2000
1700
2000
1800

$37544
$46588
$54388
$64928
$43270
$53392
$61736
$54856
$66448

L409AT
504AT
506AT
508AT
L506AT
506AT
508AT
L508AT
L508AT

409AT
506AT
508AT
508AT
504AT
506AT
508AT
508AT
508AT

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List Price*
GO-2A

240V

500V

1750
1150
850
650
1750
1150
850
650
1750
1150
850
650
1750
1150
850

2300
2000
1700
1600
2300
2000
1700
1600
2300
2000
1700
1600
2300
2000
1700

$2268
$2686
$3166
$5456
$2714
$3576
$5088
$6186
$3260
$4356
$5606
$6650
$4246
$5888
$6680

L182AT
L182AT
186AT
L186
L182AT
L182AT
186AT
218AT
L182AT
L186AT
189AT
219AT
186AT
189AT
219AT

650
1750
1150
850
650
1750
1150
850

1600
2300
2000
1700
1600
2300
2000
1700

$7884
$5686
$7010
$8402
$10840
$6930
$8464
$10760

2110AT
189AT
258AT
259AT
259AT
2110AT
258AT
288AT

10

650

1600

$13016

328AT

328AT

1750
1150
850
650
1750
1150
850
650
1750
1150
850
650
1750
1150
850
650

2300
2000
1700
1600
2300
2000
1700
1600
2300
2000
1700
1600
2300
2000
1700
1600

$7948
$10364
$12384
$15232
$10328
$12704
$15148
$19596
$11902
$14760
$18834
$23328
$13980
$17720
$21504
$26730

258AT
259AT
288AT
328AT
288AT
328AT
365AT
365AT
327AT
365AT
365AT
366AT
328AT
365AT
366AT
368AT

2110AT
259AT
327AT
328AT
288AT
328AT
366AT
365AT
327AT
365AT
366AT
366AT
328AT
365AT
366AT
368AT

Frame ➃

10

Dim. Pg.

HP

10
10
10
10
10
10
10
10
10
10
10
10

259AT
259AT
2110AT
259AT
288AT

60

75

100

125

150
200

Frame ➃

* Basic list price applies to frames listed. It does not include pricing for modifications
or accessories. Refer to Modifications section for appropriate list price addition(s).
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.
14 The NEMA definition for short time rated motors is as follows “All short time ratings
are based upon a corresponding short time load test, which shall commence only
when the windings and other parts of the machine are within 5°C of the ambient
temperature at the time of starting the test.” This means that field voltage should
be removed when the motor is not operating.
These short time rated motors have 150% occasionally repeated overload capability
at all speeds within the standard speed range. To add for wider than standard speed
range, use rated HP and the tables in page__ item __ (frame size may be different
from standard).
a 365AT page ___; 328AT page ___.

Terms

Other

Application
Information

Type CD
Shunt Wound

2.22

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Explosionproof and
Dust-Ignitionproof Motors

Nonventilateda nd
Fan Cooled

Class F Insulation
For Continuous Operation in 40°C Ambient

General
Information

Type CD
Shunt Wound

UL File #29056
CSA File #056228
Class I Group D
Class II Group E, F, G - See Page XX

5

1750
1150
2500
1750
1150
2500
1750
1150
2500
1750
1150
2500
1750
1150

2050
1380
2750
2050
1380
2750
2050
1380
2750
2050
1380
2750
2050
1380

$8082
$8457
$8568
$8790
$9609
$9162
$9927
$11085
$10674
$11916
$16776
$14061
$17058
$19719

TENV
TENV
TENV
TENV
TENV
TENV
TENV
TEFC
TEFC
TEFC
TENV
TENV
TENV
TEFC

188AT
188AT
188AT
189AT
189AT
189AT
189AT
189AT
189AT
189AT
2110AT
2110AT
2110AT
2110AT

Dim. Pg.

HP

1

1.5

2

3

5

7.5

10

Totally Enclosed Fan Cooled Explosionproof (TEFC-XP)
(Frame CD409AT shown above.)
* Basic List price applies to frames listed. It does not include pricing for modifications
or accessories. Refer to Modification section for appropriate list price addition(s).
➁ For Suitability of operation with rectified power supplies, see page xx.
➃† Standard shaft for frames CDL188AT-CD409AT is suitable for belt drive or direct
coupling (within limits given in Application Section.)
➅ TENV-Totally Enclosed Nonventilated
TEFC- Totally Enclosed Fan Cooled
10 Refer to GE for frame.
15 UL Operating Temperature Code T4-135 C.

15

20

25

30
40
50
60
75

www.gemotors.com

•

800-541-7191

1750
1150
850
2500
1750
1150
850
3500
2500
1750
1150
850
3500
2500
1750
1150
850
3500
2500
1750
1150
850
3500
2500
1750
1150
850
3500
2500
1750
1150
850
3500
2500
1750
1150
850
2500
1750
1150
850
2500
1750
1150
850
1750
1150
850
1750
1150
850
1750
1150
1750
1750

2300
2000
1700
3000
2300
2000
1700
3850
3000
2300
2000
1700
3850
3000
2300
2000
1700
3850
3000
2300
2000
1700
3500
3000
2300
2000
1700
3500
3000
2300
2000
1700
3500
3000
2300
2000
1700
3000
2300
2000
1700
3000
2300
2000
1700
2300
2000
1700
2100
2000
1700
2100
2000
2100
2100

$8082
$8457
$10635
$8568
$8790
$9609
$14310
$8316
$9162
$9927
$11085
$15768
$9393
$10674
$11916
$16776
$18789
$12057
$14061
$17058
$19719
$23634
$16452
$18732
$19491
$23811
$30267
$19821
$20868
$21399
$27684
$31158
$25740
$25173
$27618
$33300
$39765
$31101
$31794
$38745
$49443
$35133
$35691
$46512
$56448
$40695
$51327
$62745
$51516
$61155
$74730
$62145
$70557
$67659
$75387

Frame ➃†
Enclosure

➅

240V

500V

TENV
TENV
TENV
TENV
TENV
TENV
TENV
TENV
TENV
TENV
TEFC
TENV
TENV
TEFC
TEFC
TENV
TENV
TENV
TENV
TENV
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC
TEFC

188AT
188AT
188AT
188AT
189AT
189AT
2110AT
188AT
189AT
189AT
189AT
2110AT
189AT
189AT
189AT
2110AT
2110AT
2110AT
2110AT
2110AT
2110AT
288AT
2110AT
2110AT
2110AT
288AT
288AT
2110AT
2110AT
288AT
288AT
328AT
288AT
288AT
288AT
328AT
407AT
288AT
328AT
407AT
407AT
288AT
328AT
407AT
407AT
407AT
407AT
409AT
407AT
407AT
409AT
409AT
409AT
409AT

188AT

409AT

GEP387L 09/11 • Prices and data subject to change without notice.

15

Dim.
Pg.

10

Motor Pricing

Frame
➃†

Basic
List
Price*
GO-2X

10
10

189AT

Modifications
Pricing

3

➅

Rated
Top
Speed
RPM

10
10
10

189AT
189AT
189AT
2110AT
10

Accessories &
Modifications

2

Enclosure

Base
Speed
RPM

189AT
189AT
2110AT
2110AT
10

2110AT
2110AT
2110AT
288AT
10

Outline
Dimensions

1.5

Basic
List Price*
GO-2X

2110AT
2110AT
288AT
288AT
10

2110AT
288AT
288AT
328AT

Application
Information

1

Rated
Top
Speed
RPM

10

288AT
288AT
328AT
10

288AT
328AT
10
10

288AT
328AT

Other

HP

Base
Speed
RPM

PRICES - 240 and 500 Volts (Type C Power Supply➁)

10
10
10
10
10
10
10

Terms

PRICES - 180 Volts (Type K Power Supply➁)

10
10
10
10
10

2.23

Explosionproof and
Dust-Ignitionproof Motors

Nonventilateda nd
Fan Cooled
Type CD
Shunt Wound

All listed explosionproof motors meet UL operating temperature code T4A-120°C, except 75 HP, 1750 TEFC, CD409AT frame
which is UL operating temperature code T4-135°C. For 120 volt motor, see page XX, Item XX, special armature voltage.
See page XX for standard explosionproof outlines. A thermostat with a normally closed contact is included as standard.
For Class II, Groups E, F, and G (Division 1 & 2), UL listed motors in frames CD180AT-CD409AT, add $675 GO-2X. For TEAO
explosionproof, add $6612 GO-2X (CD407AT and CD409AT frames only).
For CSA approval on explosionproof motors, add as follows:
GO-2X

Frame

GO-2X

$669

CD320AT

$1338

CD210AT

$936

CD400AT

$1524

CD280AT

$1071

Modifications
Pricing

Frame
CD180AT

NOTE: Special conduit box and nameplates are required on
CSA approved motors.

Accessories &
Modifications

Motor Pricing

General
Information

Class F Insulation
For Continuous Operation in -25°C to 40°C Ambient

ACCESSORIES: Explosionproof motors are available only
with the accessories listed below. An accessory mounting
face is available. Contact GE for suitability and availability of
accessory mounting options.

Application
Information

Outline
Dimensions

Brakes

Breather Drains
Drain holes are normally selected to provide drainage of
moisture that might collect at the lowest point of the motor.
Explosionproof enclosures, as standard, do not have drain
holes. The breather drain is approved for this enclosure
when properly maintained after installation. Add $510
GO-2X per drain.

Other

Not available on explosionproof motors.

Shaft Extensions
Oversize shaft extensions are not available on
explosionproof motors.

Space Heaters
Terms

For heaters installed and leads brought out through
the motor conduit box, add $546 GO-2X.

2.24

www.gemotors.com

•

800-541-7191

For explosionproof (Class 1, Group D, Class II, Groups E, F,
and G) motor-mounted tachometer, add as follows:
GE will not mount non-explosionproof tachometers on
explosionproof motors.
GO-2X

Explosionproof brake. Refer to GE.
NOTE: These are not available with a thru shaft.

Precision Balance

Tachometers

BC42 (50V/1000RPM) or (100V/1000RPM)

$10400

Dynapar X25 (5VDC to 15 VDC Max) (240, 512, 600, 1024, 1200, 2048 PPR)
Only suitable for installation in Class 1, Group D environments

$4080

For other options, refer to GE.
Mounting kit only for BC tach for explosionproof motor (included as
part of tachometer price). Kit includes adapter, coupling, stub shaft,
and mounting bracket for BC tachometers. Mounting kit is assembled
to motor

$1806

For mounting only of customer-supplied explosionproof tachometer.
This includes coupling, stub shaft, mounting bracket, and assembly of
tachometer.

$3269

Other accessories are available. Accessories and modifications may be added only when they do not affect the
explosionproof features of the motor. All accessories must
meet or exceed environment class and group requirements
as defined by the National Electrical Code and Underwriters’
Laboratories. Refer to GE.
Note: A double shaft extension is not available on explosionproof BC tachometers.
The motors described in this section have been listed by
Underwriters’ Laboratories for application in hazardous
locations of the classes and groups referred to.

GEP387L 09/11 • Prices and data subject to change without notice.

Explosionproof and
Dust-Ignitionproof Motors

Purged/Totally Enclosed Separately
Ventilated for Hazardous Locations

Class F Insulation
For Continuous Operation in 40°C Ambient

Class II
Section 502-8 of the National Electrical Code permits the use of enclosed separately ventilated motors with air ducted-in,
air ducted-out ventilation for use in Class II, Division 1 and 2 locations, provided that the maximum surface temperatures
shall not exceed 120°C, (248°F). Auxiliary equipment such as a conduit box, tachometer, and other auxiliary devices mounted
on the motor must be of the explosionproof type for Division 1 locations. Sealed leads and standard conduit box may be
used for Division 2 locations.
Separate ventilation in hazardous locations is not available in CD180AT.
SUMMARY OF MOTOR REQUIREMENTS FOR SEPARATELY VENTILATED MOTORS IN HAZARDOUS LOCATION
MOTOR LEADS

CONDUIT BOX

TACHOMETERS

SPACE HEATERS

AUXILIARY DEVICES

DIVISION 1

SEALED

XP

XP

LOW TEMP

XP

DIVISION 2

SEALED

STANDARD

XP

LOW TEMP

XP

DIVISION 1

SEALED

XP

XP

LOW TEMP

XP

DIVISION 2

SEALED

STANDARD

XP

LOW TEMP

XP

Motor Pricing
Outline
Dimensions

CLASS I

Modifications
Pricing

Section 501-8 of the National Electrical Code permits the use of enclosed separately ventilated motors with air ducted-in, air
ducted-out ventilation in Class I, Division 1 or 2 locations when installation and operation conform to certain requirements.
Motors must be air-purged with a source of clean air and have the control arranged to prevent energization of the machine,
until ventilation has been established and the enclosure has been purged with at least 10 volumes of air. Protective devices
such as a thermostat must be utilized on the motor to detect any increase in temperature of the motor beyond the design
limits, and the control must be arranged to automatically de-energize the equipment. Motor leads must be sealed at the
frame exit (see Section 501-5 of the National Electrical Code). Auxiliary equipment such as a conduit box, tachometer, and
other auxiliary devices mounted on the motor must be of the explosionproof type for Division 1 locations. Sealed leads and
standard conduit box may be used for Division 2 locations.

Accessories &
Modifications

Class I

General
Information

Type CD
Shunt Wound

CLASS II

Application
Information

XP=Explosionproof rated for hazardous location where motor is used

Terms

Other

WARNING: Enclosed separately ventilated motors supplied for use in a hazardous location do not have an
Underwriters’ listing and are not explosionproof. Articles 501-8 and 502-8 of the National Electrical Code
governing the installation of motors in Class I and Class II locations assign approval of the installation to “the
authority having jurisdiction” (see Article 100 - Definitions of the NEC). Therefore, it is the responsibility of the
customer to be familiar with the NEC and the local jurisdictional requirements, and to determine that the motor
selection (including possibly permissible alternative ventilation systems or accessories) is “acceptable to the
authority having jurisdiction.”

www.gemotors.com

•

800-541-7191

GEP387L 09/11 • Prices and data subject to change without notice.

2.25

Papermill Duty

Totally Enclosed Nonventilated

GE produces DC motors designed specifically for papermill
PRICES - 500 Volts (Type C Power Supply➁)
applications. These ratings are available in Splashproof Fully Suitable for constant torque to 5% of base speed
Guarded Separately Ventilated (SPFG-SV) or Totally Enclosed
F Rise
B Rise
Nonventilated (TENV) enclosures. The pricing includes
Frame
Frame
Rated
Basic
Basic
standard papermill features listed below. Other modifications
➃
➃
Base
Top
List
List
Speed
Speed
Price*
Price*
may be specified. Refer to the Accessories and Modifications
HP
RPM
RPM
GO-2A
500V
GO-2A
500V
section for price adders.
1750
2300
218AT
218AT
$7170
$8186
Frames are listed for Class F temperature rise and Class B
temperature rise. Class F rise motors are rated at 1.0 Service
Factor (SF) and 150% occasional overload. Class B rise
motors are rated at 1.0 SF and 200% occasional overload,
Class F rise at 1.15 SF and 150% occasional overload. Class F
or Class B rise must be specified at the time of order. Other
combinations available and must be specified at the time
of order.
All frames listed include 40°C ambient, continuous duty,
and 240/120V or 300/150V shunt field. Voltage must be
specified at the time of order. Ratings up to and including
1250 HP are 500V armature. Ratings 1500 HP and above
are 700V armature.

2

3
5
7.5
10
15

1150
1750
1150
1750
1150
1750
1150
1750
1150
1750
1150

2000
2300
2000
2300
2000
2300
2000
2300
2000
2300
2000

$8540
$8402
$10454
$11758
$14062
$14140
$17010
$16516
$19038
$19440
$23292

218AT
218AT
219AT
2110AT
258AT
259AT
288AT
327AT
328AT
328AT
366AT

$9900
$9726
$12486
$13922
$16688
$16786
$20374
$19756
$22908
$23410
$28026

Dim.
Pg.

219AT
218AT
258AT
2110AT
259AT
259AT
327AT
327AT
328AT
328AT
368AT

* Basic list price applies to frames listed. Refer to Modification section for appropriate
list price addition(s).
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section). Frames
CD6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.

Refer to GE for backstand or unwind applications.

Standard papermill features include:
• Transparent cover (Lexan® or equivalent) located on
the conduit box side of the motor.
• Cast iron endshields on frames CD210AT-CD508AT
• Shaft grounding brush
• One normally opened and one normally
closed thermostat
• Drive end labyrinth seal
• Oversize conduit box
• Waterproof conduit box on frames
CD218AT-CD5010AY
• Special brushes
• Splashproof Fully Guarded Separately Ventilated
(SPFG-SV) or Totally Enclosed Nonventilated
(TENV) enclosure
• Air entry in drive end on separately
ventilated machine

Splashproof Fully
Guarded Self
Ventilated (SPFG-SV)
(Frame CD328AT
shown at right.)

® Registered trademark of General Electric Company.

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Class F Insulation
For Continuous Operation in 40°C Ambient

2.26

www.gemotors.com

•

800-541-7191

GEP387L 09/11 • Prices and data subject to change without notice.

Papermill Duty

Suitable for constant torque to 5% of base speed

15

20

25

30

40

$9724
$11048

218AT
2110AT

850

1700

$12604

259AT

$14774

10

650
500
400
300
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300

1600
1500
1200
900
2300
2000
1700
1600
1500
1200
900
750
2300
2000
1700
1600
1500
1200
900
750
2300
2000
1700
1600
1500
1200
900
750
2300
2000
1700
1600
1500
1200
900
750
2300
2000
1700
1600
1500
1200
900
750
2100
2000
1700
1600
1500
1200
900

$14868
$16924
$20554
$23542
$10604
$12280
$14358
$16654
$18918
$23082
$26682
$29332
$12254
$14616
$16588
$20356
$23364
$27118
$32202
$35712
$13522
$16276
$18976
$23256
$26674
$31318
$36808
$41662
$15210
$18072
$21840
$25890
$29818
$35056
$40762
$47062
$16330
$19530
$23704
$27982
$32518
$38088
$45406
$55566
$18490
$23230
$27240
$32166
$37752
$44002
$52912

288AT
327AT
328AT
368AT
219AT
258AT
287AT
327AT
328AT
329AT
368AT
368AT
258AT
288AT
327AT
327AT
329AT
365AT
366AT
409AT
259AT
327AT
328AT
328AT
329AT
366AT
407AT

$17492
$20060
$24398
$28134
$12320
$14366
$16854
$19724
$23352
$27558
$32058
$35372
$14336
$17176
$19642
$24152
$27910
$32604
$38958
$43346
$15922
$19250
$22626
$27778
$32048
$37854
$44718
$50784
$17920
$21496
$26006
$31070
$35980
$42528
$49658
$57534
$19320
$23320
$28336
$33684
$39354
$46318
$55466
$68166
$22020
$27744
$32756
$38916
$45896
$53708
$64846

288AT
327AT
328AT
368AT
2110AT

10

10

288AT
328AT
329AT
366AT
407AT
407AT
10

327AT
327AT
328AT
366AT
368AT
407AT
409AT
409AT

www.gemotors.com

•

$11220
$13066

218AT
258AT

800-541-7191

500V

F Rise, 150% O.L.

Dim.
Pg.

HP

50

10

327AT
328AT
365AT
329AT
368AT

60

10

259AT
288AT
327AT
328AT
329AT

75

10

407AT
10

259AT
327AT
328AT
328AT
329AT
407AT
409AT

100

10

288AT
328AT
328AT
10

407AT
407AT

125

10
10

288AT
328AT
329AT
368AT
407AT
10
10
10

327AT
329AT
368AT
407AT
504AT
506AT
508AT

150

Base
Speed
RPM
1750
1150
850
650
500
400
300
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250

Rated
Top
Speed
RPM

Basic
List
Price*
GO-2A

Frame
➃

2100
2000
1700
1600
1500
1200
900
2100
2000
1700
1600
1500
1200
900
750
2100
2000
1700
1600
1500
1200
900
750
2000
2000
1700
1600
1500
1200
900
750
2000
2000
1700
1600
1500
1200
900
750
2000
2000
1700
1600

$20538
$26010
$30790
$36216
$42508
$49780
$59586
$23736
$29022
$34288
$40132
$47472
$55198
$65944
$77300
$27010
$33262
$38628
$46006
$53952
$62646
$77426
$86770
$32640
$39564
$45532
$54106
$63198
$76238
$90440
$100600
$37756
$45532
$52470
$61530
$75104
$86540
$101472
$113594
$42724
$51622
$58722
$69306
$84074
$94652
$113594
$126640

328AT
329AT
368AT
368AT
504AT
409AT
508AT
L328AT
368AT
368AT
407AT
504AT
506AT
506AT
508AT
329AT
368AT
407AT
504AT
506AT
506AT
508AT

a
b
c

500

500V

10

368AT
407AT
409AT
506AT
508AT
5010AY
5010AY
6062
368AT
409AT
506AT
506AT
508AT
5010AY
6062
407AT
407AT
409AT
506AT
506AT
508AT
5010AY
6062
10

B Rise, 200% O.L.

Dim.
Pg.

Basic
List
Price*
GO-2A

Frame
➃

$24580
$31220
$37194
$43978
$51842
$60932
$73190
$28352
$34984
$41568
$48872
$58046
$67704
$81136
$96294
$32470
$40248
$46992
$56216
$66146
$77016
$95320
$106720
$39506
$48160
$55622
$66340
$77704
$93834
$112720
$124006
$45902
$55622
$64294
$75620
$92418
$106714
$125378
$140248
$52110
$63234
$72108
$85170
$103630
$116854
$140248
$156556

328AT
368AT
407AT
504AT
504AT
506AT
508AT
329AT
368AT
407AT
504AT

500V

Dim.
Pg.

Modifications
Pricing

2300
2000

287AT
328AT
328AT
329AT
368AT
368AT
409AT

Frame
➃

10

508AT
10
10

368AT
368AT
409AT
504AT
508AT
5010AY

Accessories &
Modifications

10

1750
1150

Dim.
Pg.

500V

Basic
List
Price*
GO-2A

10
10

368AT
409AT
409AT
506AT
508AT
5010AY
6058
6062
407AT
409AT
506AT
506AT
508AT
5010AY
5010AY

Outline
Dimensions

7.5

Base
Speed
RPM

Frame
➃

Application
Information

HP

B Rise, 200% O.L.

Basic
List
Price*
GO-2A

10

L409AT
506AT
506AT
508AT
5010AY
5010AY
6062

Other

F Rise, 150% O.L.
Rated
Top
Speed
RPM

10

* Basic list price applies to frames listed. Prices include standard papermill features listed
on page XX. Refer to Modification section for other accessories and modifications.
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section Frames CD
6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.
a Top speed; Class F rise=1500, Class B rise=1000
b Top speed; Class F rise=1200, Class B rise=1000
c Top speed; Class F rise=900, Class B rise=800

GEP387L 09/11 • Prices and data subject to change without notice.

Motor Pricing

PRICES - 500 Volts

2.27

Terms

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

General
Information

Splashproof Fully Guarded
Separately Ventilated

Papermill Duty

Splashproof Fully Guarded
Separately Ventilated

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Class F Insulation
Type C Power Supply➁
For Continuous Operation in 40°C Ambient

PRICES - 500 Volts

PRICES - 500 Volts

Suitable for constant torque to 5% of base speed

Suitable for constant torque to 5% of base speed

F Rise, 150% O.L.

HP

200

250

300

400

Terms

Other

Application
Information

500

600

700

Base
Speed
RPM
1750
1150
850
650
500
400
300
250
1750
1150
850
650
500
400
300
250
1150
850
650
500
400
300
250
1150
850
650
500
400
300
250
1150
850
650
500
400
300
250
1150
850
650
500
400
300
250
1150
850
650
500
400
300
250

Rated
Top
Speed
RPM

Basic
List
Price*
GO-2A

Frame
➃

2000
1800
1700
1300
1500
1200

$52876
$62730
$71492
$83832
$99688
$113752
$133300
$150340
$63892
$69030
$83970
$94266
$117884
$131260
$152434
$171910
$87044
$96966
$107816
$128386
$146614
$169994
$191980
$113570
$124420
$133060
$148810
$173342
$207380
$228790
$145010
$153784
$160258
$173656
$207514
$235682
$263426
$208634
$210586
$229898
$255938
$273604
$298068
$334526
$231134
$233218
$258230
$280750
$298664
$333464
$374726

L409AT
506AT
506AT
508AT
6062
6165
6164
504AT
504AT
506AT
5010AY
5010AY
6062
6169
6259

d

750
1900
1700
1600
1600
1500
1200
900
750
1600
1500
1500
1300
1200
900
750
1500
1500
1400
1200
1000
750
710
1500
1400
1200
1000
1000
750
710
1500
1300
1200
1000
1000
750
710
1300
1200
1000
1000
1000
750
710

B Rise, 200% O.L.

Dim.
Pg.

500V

10

508AT
5010AY
6062
6160
6169
6262
5010AY
6062
6160
6259
6262
6266
6058
6160
6164
6262
6266
6271
6066
6173
6268
6275
6280
6881
6168
6173
6270
6275
6881
6887
10

Basic
List
Price*
GO-2A

Frame
➃

$124802
$77120
$87904
$104458
$122864
$140446
$164882
$186182
$78572
$92326
$109502
$117500
$145610
$162332
$188798
$213144
$107344
$119746
$133026
$158738
$181524
$210748
$238232
$141632
$153782
$164582
$184270
$214934
$257482
$284244
$179520
$190486
$198578
$215326
$257648
$292794
$327476
$238882
$241126
$263336
$293282
$313596
$341694
$383620
$264758
$267154
$295918
$322072
$342376
$382396
$429850

L409AT
506AT
5010AY
6058
6062
6169
6169

500V

F Rise, 150% O.L.

Dim.
Pg.

800

10

506AT
508AT
5010AY
6062
6062
6169
6262

900

10

1000

5010AY
5010AY
6062
6160
6169
6262

1250

6058
6160
6164
6262
6266
6271

www.gemotors.com

•

800-541-7191

Basic
List
Price*
GO-2A

Frame
➃

1150
850
650
500
400
300
250
1150
850
650
500
400
300
250
1150
850
650
500
400
300
250
1150
850
650
500
400
300

1250
1000
1000
1000
1000
750
710
1250
1000
1000
1000
1000
750
710
1250
1000
1000
1000
1000
750
710
1150
1000
1000
1000
900
750

$254218
$256600
$282316
$304214
$324882
$362808
$406226
$283096
$285268
$305916
$325874
$346346
$386838
$439002
$307034
$308656
$328104
$350180
$370412
$414450
$470502
$365570
$367448
$387170
$407148
$431396
$481984

6173
6270
6275
6280
6881
6887

500V

B Rise, 200% O.L.

Dim.
Pg.

10

6268
6270
6275
6779
6887
6985
10

6268
6270
6774
6881
6887
6985
6991
6776
6778
6785
6896
6996
10

Basic
List
Price*
GO-2A

Frame
➃

$291560
$294298
$323872
$348760
$372528
$416144
$466076
$324770
$327266
$350718
$373664
$397214
$443778
$503666
$352004
$354164
$376232
$401620
$424888
$475430
$539892
$419320
$421480
$444160
$467136
$494940
$553096

6268
6270
6275
6779
6887
6985

500V

Dim.
Pg.

10

6268
6270
6774
6779
6887
6985
10

6776
6778
6785
6896
6996
6999
10
10

6890
6896
6996
6999
10

PRICES - 700 Volts
(3 Phase, 6 Controlled Pulse Power Supply➁)
Suitable for constant torque to 5% of base speed

6157
6160
6164
6262
6275
6779

F Rise, 150% O.L.

6168
6268
6270
6275
6779
6881

HP

1500

6268
6270
6275
6779
6881
6887

1750

10

* Basic list price applies to frames listed. Prices include standard papermill features listed
on page XX. Refer to Modification section for other accessories and modifications.
➁ For suitability of operation with rectified power supplies, see page xx.
➃ Standard shaft for frames CDL182AT-CD5010AY, CD6000, and CD6100 is suitable
for belt drive or direct coupling (within limits given in Application Section Frames CD
6200, CD6700, CD6800, and CD6900 are suitable for direct drive only.
10 Refer to GE for frame.
d Top Speed; Class F=900, Class B=600

2.28

HP

Base
Speed
RPM

Rated
Top
Speed
RPM

2000

Base
Speed
RPM

Rated
Top
Speed
RPM

Basic
List
Price*
GO-2A

Frame
➃

850
650
500
450
400
350
850
650
500
450
850
650
500

1000
900
850
810
770
720
960
900
800
760
900
840
750

$421084
$443962
$467074
$480620
$494164
$535180
$473302
$498796
$524814
$649850
$590782
$628102
$677922

6876
6881
6996
6999
6999
6991
6881
6990
6996
6999
6896
6996
6999

700V

B Rise, 200% O.L.

Dim.
Pg.

Basic
List
Price*
GO-2A

Frame
➃

$483060
$509370
$535948
$551524
$567102
$614268
$543112
$572428
$602348
$746140
$678214
$721132
$778424

6986
6990
6999

700V

Dim.
Pg.

10

6999
10
10

6996
6999
10

6896
6996
6999

NOTE: Motors rated 1000HP and above may need external reactance (supplied by
customer) included in the circuit to limit ripple current when powered by rectified power
supplies (see page XX).

GEP387L 09/11 • Prices and data subject to change without notice.

3000
3500

www.gemotors.com

•

800-541-7191

TR-15905
TR-15906

GEP387L 09/11 • Prices and data subject to change without notice.

12.5
12.5

2.29

Motor Pricing
Modifications
Pricing
Accessories &
Modifications
Outline
Dimensions
Application
Information
Other

If input frequency is 60 hertz and no series inductance is
added externally to the motor armature circuit, these
Motors are suitable for operation with MG sets or with the
quantities need not be indicated and shall be permitted to be
rectified power supplies described below:
omitted from the identification of the power supply. However,
a. Single-phase, full wave, 60 cycle
if one of these qualities is indicated, then both shall appear
(Power Supply Identification K)
Only motors rated 7.5 HP or less, 180 Volts, are suitable for to avoid confusion (NEMA MG1-2009, part 10.61.2).
this type of power supply. These ratings do not require an For other types of power supplies, refer to GE.
external reactor. For AC supplies other than 230 volts, 60
Standard shunt field voltages are as shown under field voltage
cycle, refer to GE.
modification. (Refer to the Modifications Section Item XX)
b. Three-phase modified, 60 cycle
Reactors
(Power Supply Identification D)
All DC motor ratings in CD6000-CD6900 frames operating
This power supply has three controlled rectifiers and three
on twelve pulse, three phase rectified power supplies and
uncontrolled rectifiers plus a free-wheeling rectifier. It
all ratings in CD6000-CD6200 frames operating on less
produces the three pulses per cycle. Motors rated 250 HP
than twelve pulse rectified power supplies do not require
or less in frames CD5010AY and below may be used on
external inductance.
this type of power supply. No external reactors are
DC motor ratings in CD6700-CD6900 frames operating on less
required for motors in frames CD5010AY and below,
than twelve pulse rectified power supplies may require external
although improved operation at low speeds may be
inductance to limit the armature circuit current ripple to assure
obtained on frames CD365AT-CD5010AY using a reactor.
acceptable commutation and long brush, commutator and
The 240 volt motors are based on 230 volt, three-phase,
bearing life. Armature current ripple is determined by power
60 cycle AC voltage applied to the rectifier bridge, while
supply type, ration of DC to AC line voltage, and total circuit
the 500 volt motors are based on 460 volt, three-phase,
inductance. For DC motors in CD6700-CD6900 frames rated at
60-cycle AC voltage applied to the rectifier bridge.
the following horsepower and speed combinations or for any
c. Three-phase, full wave 60 cycle
rating in CD6700-CD6900 frames having an armature circuit
(Power Supply Identification C)
inductance of 0.2mH and less, GE recommends a 0.5mH
This power supply has six controlled rectifiers and produces
external reactor. GE experience indicates that this is especially
six pulses per cycle. The 240 volt motors are based on 230
true of applications where the motor is operated at rated load
volt, three-phase, 60-cycle AC voltage applied to the rectifier
and speed or higher for extended periods.
bridge, while the 500 volt motors are based on 460 volt,
Horsepower
Base Speed (RPM)
three-phase, 60-cycle AC voltage applied to the rectifier
1000-1250
850 and above
1500
650 and above
bridge. Motors in AC voltage CD6000-CD6900 are suitable
1750-3000
500 and above
only for operations from six-controlled, 3 leg power supplies.
d. Three-phase, full wave other than 60-cycle, 240 volt DC When external reactance is used, it should be installed in
(230 volt AC) or 500 volt DC (460 volt AC)
series with the A1 leads of the motor.
Power supplies of this type require identification
The reactor should be sized to have the following:
as follows:
Continuous and overload DC rating equal to the motor rating.
M/N F-V-H-L where:
AC RMS current rating equal to 25% of motor DC rated current
M = a digit indicating total pulses per cycle.
for large variance between AC supply and rectified DC voltage.
N = a digit indicating controlled pulses per cycle.
Frequency rating equal to 360 Hz
F = free wheeling (this letter appears only if free
Enclosure equal to NEMA 1 or as suitable for environment.
wheeling is used).
Following is one source for the reactors described above:
Transformer Engineering Corporation
V = three digits indicating nominal line-to-line AC voltage
2550 Brookpark Road, Cleveland, Ohio 44134
to the rectifier.
Ph. (216) 741-5282
H = two digits indicating input frequency in hertz
DC Current
Design
%AC RMS Amps of DC Amps
L = one, two, or three digits indicating the series induc1000
TR-15902
25
1500
TR-15903
25
tance in millihenries (may be zero) to be added
2000
TR-14711
25
externally to the motor armature circuit.
2500
TR-15904
12.5

Terms

Motor Operation from Rectified Power Supplies

General
Information

Power Supplies

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing
Motor Pricing

General
Information

Motor Pricing

Notes

2.30

www.gemotors.com

•

800-541-7191

GEP387L 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.

3.2
3.2
3.2
3.2
3.2
3.3
3.4
3.4

.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.

3.8
3.8
3.9
3.10
3.11
3.11
3.12
3.13
3.15
3.17
3.17

20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37

Overload-Maximum Load . . . . . . . . .
Pump Motors . . . . . . . . . . . . . . . .
Seals, Drive End Shaft . . . . . . . . . . .
Severe Mechanical Duty . . . . . . . . .
Shaft Extensions . . . . . . . . . . . . . .
Shaft Grounding Brush . . . . . . . . . .
Space Heaters. . . . . . . . . . . . . . . .
Speed Limit Device . . . . . . . . . . . . .
Speed Range Greater than
Standard by Field Control . . . . . . . . .
Tachometer Generator Equipment . . .
Terminal Board in Conduit Box . . . . . .
Tests and Curves . . . . . . . . . . . . . .
Temperature Detectors . . . . . . . . . .
Vertical Mounting . . . . . . . . . . . . . .
Voltages . . . . . . . . . . . . . . . . . . .
Warranty Extension . . . . . . . . . . . .
Windings, Stabilized Shunt, Compound
or Series . . . . . . . . . . . . . . . . . . .
Mod Shop Pricing . . . . . . . . . . . . . .

.
.
.
.
.
.
.
.

3.17
3.18
3.18
3.18
3.19
3.20
3.20
3.21

.
.
.
.
.
.
.
.

3.22
3.24
3.28
3.29
3.30
3.30
3.31
3.31

. 3.32
. 3.34

Motor Pricing

.
.
.
.
.
.
.
.

Accessories &
Modifications

.
.
.
.
.
.
.
.

Accessories &
Modifications

.
.
.
.
.
.
.
.

Application
Information

.
.
.
.
.
.
.
.

Page

Other

10
11
12
13
14
15
16
17
18
19

Accessory Mounting . . . . . . .
Air Pressure Switch . . . . . . . .
Altitude . . . . . . . . . . . . . . .
Ambient Temperature . . . . . .
Balance, Mechanical . . . . . . .
Bases . . . . . . . . . . . . . . . .
Bearings . . . . . . . . . . . . . .
Brakes. . . . . . . . . . . . . . . .
Canadian Standards
Association (CSA) . . . . . . . . .
European Standards, CE Marks
Conduit Boxes . . . . . . . . . . .
Covers. . . . . . . . . . . . . . . .
Crane Motors . . . . . . . . . . .
Customer-Supplied Material . .
Drains . . . . . . . . . . . . . . . .
Enclosures . . . . . . . . . . . . .
Endshields . . . . . . . . . . . . .
Export Boxing . . . . . . . . . . .
Grease and Fittings . . . . . . .

Item Description

Terms

1
2
3
4
5
6
7
8
9

Page

Outline
Dimensions

Item Description

General
Information

CD180AT through CD6900
Index

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.1

Accessories and Modifications

ITEM
1

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

2

DESCRIPTION
ACCESSORY MOUNTING
The accessory mounting face is standard on all CD180ATCD6900 frames, permitting the ease of adding a variety of
accessories, including tachometers and speed limit switches.
When accessories are not specified, the accessory mounting
face and shaft extension are protected by a solidly attached
cover that can be removed easily. (Outlines on pages ___ and
___)
On TEFC CD180AT and CD210AT frames and all explosionproof frames, accessory mounting face is not available.

Accessory Mounting—Standard motor frames CDL182ATCD5010AY are constructed to allow the addition of
tachometers or speed limit switches.

AIR PRESSURE SWITCH
Differential air pressure switch (1-form-C contact, 10amp, 120V,
60 Hz) Used to indicate positive pressure into the motor from an
external source. CAUTION: Switch must be mounted vertical.

3

$2782
$3650

ALTITUDE
Motors and generators are suitable for operation at altitudes from sea level to 3,300 feet above sea level. For other
conditions, refer to GE or frame sizes.
List Price Additions

4

Application
Information

Outline
Dimensions

Accessories &
Modifications

List Price Addition
Blower Ventilated/Separately Ventilated Motor
Totally Enclosed Air-To-Air Cooled (Internal air circuit only)

Terms

Other

5

3.2

Altitude

Frames CD5010AY

Frames CD6000 and Above

3,301-8,800 Ft.
8,801-15,000 Ft.

Add 15%
Add 22%

Add 10%
Add 15%

AMBIENT TEMPERATURE
Standard motor is suitable for operation in an ambient
temperature of 0°C to 40°C. For ambient temperature
greater than 40°C, see List Price adder at right:
Refer to GE for frame size.
Refer to GE for applications in an ambient
temperature higher than 65°C or lower than 0°C.

List Price Additions
Ambient

500 HP and Less

600 HP and above

41°C-60°C
61°C-65°C

Add 20%
Add 25%

Add 10%
Contact GE

BALANCE, MECHANICAL
Vibration measurements are made on motor bearing housings as described in NEMA Standard 1.12.06. Amplitude is
expressed as inches peak-to-peak. Vibration limits for standard and precision balance are for the motor only
without any mounted accessory.
The same limits can generally be met with motor-mounted blowers, PY, and AN tachometers.
Motors with a BC tachometer or a motor-mounted brake will have peak-to-peak amplitudes of 2 times the value
shown below.
Where vertical mounting is required, it should be specified on the order. (For special run out, refer to GE.)
NEMA Standard Vibration Limits
Maximum NP Rated RPM

Peak-to-Peak Amplitude (inches)

3000-4000
1500-2999
1000-1499
0-999

0.0010
0.0015
0.0020
0.0025

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

DESCRIPTION

Precision balance
limits at top speed

0.0002

CD320AT-CD360AT

CD407AT-CD5010AY

PEAK-TO-PEAK AMPLITUDE (INCHES)
0.0003

0.0004

MOTORS LIST PRICE
Description

Up to
$2500

$2501 to
$3592

$3593 to
$5578

$5579 to
$9748

$9749 to $13219 to $23923 to $42137 to $61751 to
$13218
$23922
$42136
$61750
$98628

$98629
and up

List Price Addition
Precision Balance

Not Available

$1338

$1582

$2094

$2688

$3210

$4564

$5490

Not Available

BASES

For P-Base see Endshields, Page 3.15.

6a

Standard Sliding Base
Sliding bases are suggested as a convenient means for adjusting belt tension or may be used as mounting plates.
(For horizontal mounting only — not available for ceiling or sidewall mounting.)
(Not available on CD6700 through CD6900 frames)

6b

Transition Base
Transition bases may be used to match the mounting dimensions of another motor which has a larger “D”
dimension. (A drawing must be provided at the time of order.) This option is available if, and only if, the shaft
height of the older motor is reasonably higher (varies with motor size, but typically greater than 1 inch is sufficient)
than the shaft height of the Kinamatic™ motor at the same rating. For horizontal floor mounting only. Refer to
Replacement Motors/Mechanically interchangeable section on page 10 for additional details. A special shaft
extension may be required.

6c

Sole Plate
Sole plates are two (2) flat steel plates to be mounted in concrete by the customer to provide a mounting surface for
the motor. Refer to pages ___-___ for outlines.

Outline
Dimensions

Accessories &
Modifications

6

Accessories &
Modifications

CD210AT-CD280AT

MOTOR LIST PRICE
Description

Up to
$2500

$2501
to
$3592

$3593
to
$5578

$5579 $9749 $13219 $23923 $42137 $61751 $98629 $157704 $252289 $403651
to
to
to
to
to
to
to
to
to
and
$9748 $13218 $23922 $42136 $61750 $98628 $157704 $252288 $403650
up

a. Standard Sliding Base

$316

$316

$316

$540

$630

$1216

$1600

$2160

$2860

$3844

$6154

b. Transition Base

$700

$810

$944

$1260

$1700

$2300

$3100

$4160

$5560

$7440

$10022

$13724

$18070

c. Sole Plate

$630

$630

$630

$870

$1110

$1530

$2090

$2760

$3750

$5026

$6760

$9150

$12300

Application
Information

Frame Size

Motor Pricing

5 Improved balance vibration limits (applies to listed ratings only). For other speed ranges, refer to GE. Precision
Cont’d balance is not available on CD180AT, CD6000-CD6900 frames, nor explosionproof motors.

Contact GE

Terms

Other

ITEM

General
Information

CD180AT through CD6900

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.3

Accessories and Modifications

ITEM

DESCRIPTION

7

BEARINGS (Belted Drive)
Standard shaft for frames CD180AT-CD6100 are suitable for either belt drive or direct coupling within the limits
given in the application section on page XX (was page 179). Frames CD6200-CD6900 are suitable for direct drive
only. Where the maximum radial load at the end of the shaft exceeds the standard limits, oversize ball bearings and
roller bearings are available as listed below. Maximum radial loads and speeds for these modifications are given on
pages ____

Motor Pricing

General
Information

CD180AT through CD6900

STANDARD SIZE ROLLER BEARING ON DE
CD287AT, CD288AT

Add $1044

OVERSIZE ROLLER BEARING ON DE*

CD218-CD2110

Add $366

CD287AT, CD288AT

Add $1210

CD258-CD288

$468

CD327AT, CD328AT, CD329AT

$1044

CD327AT, CD328AT, CD329AT

$1210

CD327-CD328

$574

CD365AT-CD508AT

$1732

CD365AT-CD5010AY

$2498

CD365-CDL407

$680

CD6000 (Top spd. 1750 RPM)

$3334

CD409-CDL409

$766

CD6100 (Top spd. 1500RPM)

$3860

CD504-CDL508

$892

Not Available on frames
CD180AT, CD210AT, CD258AT,
CD259AT, CD5010AY, CD6200,
CD6700, CD6800, CD6900

Not available on frames
CD180AT, CD210AT, CD258AT,
CD259AT, CD6000-CD6900

* When an oversize bearing on DE is specified, a standard DE shaft extension will be furnished. However, if also required an oversize DE shaft is available at no
additional price.

8

BRAKES — Refer to GE for application of brakes rated above 100%
of rated motor torque.
Order must specify AC/DC voltage and frequency, torque rating
(Lb. Ft.), enclosure, and orientation with respect to the motor.
Customer is responsible for specifying brake torque rating.
GE does not recommend the use of brakes on TEFC Kinamatic
motors. When brakes are required, GE recommends TEAO
enclosures.

8a

BRAKES, DISC TYPE
These brakes are applicable for holding service within rating
limitations shown in the table on the next page. Where brakes are
required for stopping duty, the heat-dissipating capacity may be the
Disc type brakes — Disc type brakes are commonly
determining factor in the brake selection. In such cases, refer to GE.
used on ratings 250 HP and below. The brakes are
continuously rated and can be mounted on CD180ATBrakes are continuously rated and are nonadjustable spring set and
CD5010AY frames.
electrically released. For brakes of a specific manufacturer, nonlisted
capacity, or adjustable or electrically set brakes, refer to GE. For frames
CD6000-CD6900, use floor-mounted brakes.
AC brakes are recommended on disc brake applications wherever possible, especially for those applications where
high cycling duty may occur (e.g., on hoist or screw-down applications). Use a brake of standard enclosure with
dripproof fully guarded or splashproof fully guarded motors, and on TENV and TEAO motors for applications in
ambients containing chips and/or non-abrasive, non-conducting, and non-explosive dusts and coolants.

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Accessories &
Modifications

OVERSIZE BALL BEARING ON DE*

3.4

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

Motor Pricing

Standard brake features include:
•  Class B Insulation 
•  Standard AC brake coils are rated as follows:
•  Spring Set, electrically released
Nominal
Suitable Range
460
440-480
•  Manual release with automatic reset
60Hz
230
220-240
•  Standard or dust tight waterproof enclosure
380
360-400
50Hz
•  CSA certification
190
180-200
•  115 or 230 Volt DC coils
•  Horizontal mounting 
Note: Single voltage coils are supplied on brakes rated 750 lb. ft. and above.
Voltage must be specified at time of order.

WARNING:
Brake performance and features must be carefully matched to the requirements of the application. Consideration
must be given to torque requirements, especially where an overhauling condition exists, as well as thermal
capacity, ambient temperature, atmospheric explosion hazards, type of enclosure, power supply characteristics,
and other unusual conditions.
Improper selection or installation of a brake and/or lack of maintenance may cause brake failure, which can result
in damage to property and/or injury to personnel.
If injury to personnel could be caused by brake failure, proper safeguards must be provided to ensure safety of
personnel.

Motor Torque (Lb. Ft.) =

$1184
$1248
$1248
$1248
$1316
$1417
$1619
$2024
$2833
$3778
$8703
$9040
$9715
$10524
$11738
$18889
$20913
$22937

$1882
$1980
$2058
$2058
$2125
$2226
$2429
$2833
$3643
$4587
$10052
$10389
$11064
$11873
$13088
$20913
$22937
$24961

$1815
$1903
$2017
$2017
$2085
$2186
$2388
$2793
$3602
$4547
$10814
$11151
$11826
$12636
$13850
$22431
$24455
$26479

$2554
$2808
$2827
$2827
$2894
$2995
$3198
$3602
$4412
$5356
$12163
$12501
$13175
$13985
$15199
$24455
$26479
$28503

Application
Information

3600
3600
4000
4000
4000
4000
4000
4000
4000
4000
3600
3600
3600
3600
3600
1800
1800
1800

Other

1.5
3
6
10
15
25
35
50
75
105
125
175
230
330
440
500
750
1000

Motor Mounted Brake
AC Coil
DC Coil
Standard Enclosure
Dust Tight/Waterproof
Standard Enclosure
Dust Tight/Waterproof
NEMA 2
NEMA 4
NEMA 2
NEMA 4
IP23
IP54
IP23
IP54

Terms

Lb. Ft.

Maximum
Horizontal
Speed
(RPM)

HP x 5252
Motor base speed (RPM)

Customer is responsible for specifying brake torque rating.

www.gemotors.com

•

800-541-7191

Accessories &
Modifications

8a
Cont’d

Accessories &
Modifications

DESCRIPTION

Outline
Dimensions

ITEM

General
Information

CD180AT through CD6900

GEP387M 09/11 • Prices and data subject to change without notice.

3.5

Accessories and Modifications

ITEM

DESCRIPTION

8a OPTIONS: (Prices below in addition to brake price on previous page)
Cont’d
BRAKES WITH ACCESSORY MOUNTING
When mounting a second accessory (such as a 56 C-face tachometer or a speed limit device) on DPFG, TENV, TEAO,
TEAAC or TEWAC motors, a brake with accessory mounting is required. Add as follows: (Exceptions are noted below)

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

Brake Torque Lb. Ft.

List Price Addition

10-105
125-440
500-1000

$3976
$4446
$4800

Accessories &
Modifications

Note: Only “AN” style tachometers or a speed limit switch can be mounted with a brake on CD180AT frames. Brake
with accessory mounting is not required because the brake is mounted on the tach or speed switch.
Note: When mounting a brake (up to and including 330 lb. ft.) with a Northstar or Avtron Type AN-DG tach a
standard brake can be used. The brake is mounted on the tach.
Note: AN-DG tachs will not be mounted outboard a brake.

Application
Information

Outline
Dimensions

VERTICAL MOUNTING
For a brake mounted above the motor on DPFG or TENV motors, add as follows:
List Price Addition

1.5-6
10-105
125-1000

$458
$640
$1132

BRAKE SPACE HEATER

BRAKE RELEASE INTERLOCK SWITCH

A brake space heater should be specified whenever a
heater is required on the motor. For brake space
heater, add as follows:

Add as follows:

Brake Torque Lb. Ft.

List Price Addition

Brake Torque Lb. Ft.

List Price Addition

1.5-105
125-1000

$320
$480

1.5-105
125-440
500-1000

$708
$842
$1560

EXPLOSIONPROOF BRAKES
Refer to GE

Terms

Other

8b

Brake Torque Lb. Ft.

3.6

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

ITEM

DESCRIPTION

Motor Pricing

DISC BRAKES — CRANE APPLICATIONS
Brakes used on the gantry or trolley function on dockside, portal, or queue cranes require special brakes.
Order must specify crane duty and whether trolley or gantry. The features listed below are included on crane
duty brakes.

Accessories &
Modifications

Accessories &
Modifications

Standard Crane Duty Brake Features include:
•  Splined hubs (Zinc plated) and discs
•  Stainless steel self-adjusting assembly
•  Full mechanical release with side mounted release lever.  Note: Release is not self-resetting
•  Stainless steel hardware
•  Space heaters
•  Brake interlock switch
•  Dust tight, waterproof enclosure
•  56" lead lengths
When specifying vertical or horizontal, add as follows:
Motor Mounted Brake
AC Coil
Dust Tight/Waterproof

Lb. Ft.

50
75
105
125
175
230
330
440

$5751
$6561
$7545
$13538
$13875
$14651
$15460*
$16945*

Horizontal
Trolley

Gantry

$5238
$6048
$6992
$12762
$13099
$13774
$14583*
$15798*

$5238
$6048
$6992
$17022*
$17359*
$18034*
$18843*
$20058*

Application
Information

Vertical

Outline
Dimensions

List Price Addition

Viton Gasket:
Proximity Switch:
Breather Drain:
Terminal Board: 

Other

* Includes fabricated commutator endshield.
Lb. Ft. Torque =
HP x 5252
Motor base speed (RPM)

To replace standard neoprene gasket.
To replace standard brake interlock switch (microswitch).
To replace standard drain plug.
To replace 56" lead lengths.
List Price Addition

Brake Rating

Viton Gasket

Proximity Switch

Breather Drain

Terminal Board

105 Ft. Lb. and Smaller
125 Ft. Lb. and Larger

$138
$220

$1855
$3767

$552
$614

$180
$180

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Terms

8c

General
Information

CD180AT through CD6900

3.7

Accessories and Modifications

ITEM
9

DESCRIPTION
CANADIAN STANDARDS ASSOCIATION (CSA) APPROVAL
For CSA approval, no price addition except for TEAAC, TEWAC enclosures in a CD5010AY frame, add $500 NET.
For explosionproof motors adder, refer to page 2.24.
Note: CSA approval must be specified at time of order.

10

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

CE MARK, EUROPEAN STANDARDS
This modification provides for a motor that meets the standards requirements of the Low Voltage Directive 73/23/
EEC and relevant sections of the Machinery Directive 98/37/EC and EMC Directive 89/336/EEC. These motors will be
CE marked on the nameplate in accordance with the marking requirements of the Low Voltage Directive.
FRAME SIZE
CD210ATCD320AT

Motor Enclosure

CD360AT

CD400ATCD500AT

CD6000-CD6200

CD6700-CD6900

$3200
$5310
$6400

$3700
$5310
$9530

List Price Addition

Accessories &
Modifications

SPFG*, SPFG-SV*, TENV, TEFC
SPFG-BV*, TEWAC, TEAO
TEAAC

$2000
$3154 •

$2100
$3254 •
$4408

$2900
$4054 •
$5208

* The price addition for CE mark does not include the splashproof enclosure modification. See splashproof enclosure price additions on page __.
• TEWAC not available on CD210AT-CD400AT frame motors.

Application
Information

Outline
Dimensions

CE mark pricing includes:
•  Terminal board in conduit box
•  Ground lug in conduit box
•  Ground lug and tapped holes in foot (only on motors rated 100kw and higher)
•  Special nameplates
•  50 Hz marked blower motor(s) on blower ventilated, TEAO, TEAAC, TEWAC
•  Declaration of Conformity, Declaration of Incorporation 
•  Instruction book in either Spanish, French, German, Italian or English

Terms

Other

Note: All CE marked motors must be reviewed with Engineering to make sure CE temperature rise limits are met. If
the standard motor does not meet CE mark temperature rise limits (on armature and comm field), the price
addition for Class B temperature rise must be used in addition to the above CE mark price additions.
Note: CD180AT and Explosionproof ratings are not available for CE marking.
Note: DPFG, DPFG-BV, and DPFG-SV motor enclosures are not available for CE marking.
Note: CE approved accessories must be used.

3.8

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

11

CONDUIT BOXES, SPECIAL
Note: F1 - The conduit box is located on the right-hand side (as viewed from the commutator end).
F2 - The conduit box is located on the left-hand side (as viewed from the commutator end).
On CD180AT frames, other than explosionproof, the conduit box is built into the endshield and is available in the
F1 location only. On all other frames, a standard conduit box is used. CD6000-CD6900 frames, as standard, provide
a conduit box with fixed terminations for armature, field, and internal accessory leads. Special conduit boxes are as
follows:

11a AUXILIARY CONDUIT BOX OR CONDULET
Allows accessory leads to be brought into a separate conduit box of condulet. When this feature is specified, the
auxiliary conduit box or condulet will always be supplied on the side of the motor which is opposite to the main
conduit box location.
Note: The purchaser must specify which accessory leads are to be brought to the auxiliary conduit box or condulet.
Accessories external to the motor are not wired to the auxiliary box or condulet.

The addition of this modification does not provide a U.L. listed explosionproof motor.
A thermostat is required when an explosionproof conduit box is supplied with a separately ventilated motor. Accessories such as tachometers or brakes mounted on the motor must be of the explosionproof type. See
page 24, Item 28 for BC tachs. Refer to GE for explosionproof brakes.
11d OVERSIZE CONDUIT BOX
Supplied at no additional price on frames CD218AT-CD5010AY upon request. Price addition is required for oversize
conduit box on frames CD6000-CD6900.

Terms

Other

11e TOP MOUNTED CONDUIT BOX
On frames CD218AT-CD5010AY, top mounted conduit boxes are not available with a TEAAC or TEWAC enclosure.
Refer to GE for top mounted conduit boxes on blower ventilated CD218AT-CD5010AY frames. Top mounted
explosionproof box not available on CD210AT-CD320AT.

Application
Information

11c EXPLOSIONPROOF CONDUIT BOX AND SEALED LEADS ON SEPARATELY VENTILATED MOTORS
(Not available on frames CD180AT)
For use only on enclosed separately ventilated motors with air ducted-in and air ducted-out ventilation.
Section 501-8 and 502-8 of the National Electrical Code permits the use of enclosed separately ventilated
motors with air ducted-in and air ducted-out ventilation in certain locations, when installation and operation
conform to certain requirements. It is the responsibility of the user to obtain approval from the local authorities
for such installation.
For additional information, see page __.

Outline
Dimensions

Accessories &
Modifications

11b CAST IRON CONDUIT BOX
Not available on all frames.

Motor Pricing

DESCRIPTION

Accessories &
Modifications

ITEM

General
Information

CD180AT through CD6900

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.9

Accessories and Modifications

ITEM

DESCRIPTION

11f

WATERPROOF CONDUIT BOX
For use on splashproof or better enclosure. For use where motors are required to exclude water applied from a hose
and for outdoor application. Included in the price addition for waterproof motor enclosure. Not available on frames
CD6000-CD6900. The standard conduit box used on frames CD6000-CD6900 is gasketed and “water-resistant.”

Motor Pricing

General
Information

CD180AT through CD6900

MOTOR FRAME SIZE
CD210ATCD320AT

SPECIAL CONDUIT BOX

CD360ATCD400AT

CD504ATCD508AT

CD5010AY

CD6000CD6200

CD6700CD6900

$4780

$754
$376
$225

$1508
$754
Refer to GE

$1508
$754
Refer to GE

$1508
$754
Refer to GE

$3954

$2116

$6658

$8256

$12044

$51784

$51784

$1875

$1238

$1238

$1806

$7766

$7766

0
$838*
$450

0
$2106*
$900

0
$2106*
$900

0
$2106*
$900

$1730
$1730
$4606*
$9414*
Not Available

Not Available

* Not available in all enclosures. Refer to Item 11e.

12

Outline
Dimensions

Accessories &
Modifications

Accessories &
Modifications

List Price Addition
a. Auxiliary conduit box or condulet:
Conduit box for accessory leads
Condulet for accessory leads
b. Cast iron conduit box
c. Explosionproof conduit box with motor
leads sealed at the frame exit
Standard conduit box with motor leads
sealed a the frame exit
d. Oversize conduit box
e. Top mounted conduit box
f. Waterproof conduit box

COVER, TRANSPARENT
A single transparent cover is used in place of the metal cover on a brush opening at the commutator end. On
frames CD218AT-CD5010AY, the standard transparent cover is Lucite® or equivalent. On frames CD6000-CD6900,
the standard transparent cover is Lexan® or equivalent. Lexan® is available on frames CD218AT-CD5010AY.
See below for pricing per motor.
MOTOR LIST PRICE

Application
Information

DESCRIPTION

Up to
$2500

$2501 to $3593 to $5579 to $9749 to
3592
$5578
$9748 $13218

$13219
to
$23922

$23923
to
$42136

$42137
to
$61750

$61751 $98629 $157704 $252289
$403651
to
to
to
to
and up
$98628 $157704 $252288 $403650

List Price Addition
a. Lucite® or equivalent

b. Lexan® or equivalent

(Not available
on all CD180AT
frames or
CD210AT TEFC
frames.)

$270

$270

$406

$406

$406

$406

$540

$540

$540

$812

$812

$812

$812

$1080

Not Available

$1080

$1080

Terms

Other

Lucite® is a registered trademark of DuPont Company.
Lexan® is a registered trademark of General Electric Company.

3.10

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

$1080

$1352

Accessories and Modifications

13

CRANE MOTORS
GE builds DC motors designed specifically for dockside and floating crane applications. Motors in these applications
are main hoists, boom hoists, trolleys, and gantries.
Note: CD180AT frames or AN-DC tachs are not used in crane motor applications. Similarly, TEFC enclosures are not
suitable for crane applications (use TEAO), TEAAC and TEWAC waterproof enclosures are not available.

CD210ATCD250AT

CRANE MOTORS
a. Indoor main hoist/boom hoist
b. Outdoor trolley/gantry
c. D-flange

$3806
$964

CD280AT
Not Applicable
$4492
$1054

MOTOR FRAME SIZE
CD360ATCD320AT
CD400AT
List Price Addition
$4492
$3466**

$2592
$5208
$5322**

CD504ATCD5010AY

CD6000CD6200

$2592
$5792
$6824**

$6382
Not Available

Indoor main hoist/boom hoist features include:

Outdoor trolley/gantry features include:

•  Crane duty paint
•  Space heater
•  Normally closed thermostat
•  Special conduit box adapter

•  Waterproof features
•  Crane duty paint
•  Space heater
•  Normally closed thermostat

Accessories &
Modifications

** Price includes special bracket.

Motor Pricing

DESCRIPTION

Accessories &
Modifications

ITEM

General
Information

CD180AT through CD6900

Outline
Dimensions

•  Special conduit box adapter

Terms

Other

Application
Information

Note: For crane duty brakes, see page 3.7, Item 8c.
For voltages other than those listed above, refer to page 3.32 Item 34.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.11

Accessories and Modifications

ITEM
14

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

DESCRIPTION
CUSTOMER-SUPPLIED MATERIAL
No testing is performed and no warranty is provided for customer-supplied material.
All customer-supplied material must be sent to the following.
Frame Size
CD180AT-CD5010AY

Monterrey
L&M/GE Industrial Motors
605 NAFTA Blvd
Milo Distribution Center
Laredo, Texas 78045
Attn: Customer Service

CD6000-CD6900

14a BRAKE WHEEL
Customer-supplied DS brake wheels must be completely machined and dynamically balanced prior to receipt at the
factory. The factory cannot rebalance the motor after assembly of customer-supplied brake wheel.
Add $3192 list per motor. This price addition is for mounting a brake wheel on the commutator end shaft
extension only. Contact GE for mounting any other brake components or assemblies to the motor.
Note: Refer to GE for application of brakes rated above 100% of rated motor torque.
Mounting/installation instructions, outline dimensions, and parts list must be received at the time of order. Brake
wheel must be received at the factory a minimum of 3 weeks prior to customer promise ship date. Brake wheel
mounting on frames CD182AT-CD5010AY requires a commutator end shaft extension adder. Refer to page 3.19,
Item 24. No adder required for Comm End Shaft Extension on CD6000-CD6900 frames.
14b COUPLINGS (Customer to supply installation instructions for coupling to GE)
For mounting a coupling (which must be completely machined and balanced prior to receipt at the factory), WITH
finish bore and keyseat, add $3192 list per motor. The factory cannot rebalance the motor after assembly of
customer-supplied coupling. Finish bored and key seated coupling and outline drawings must be received at the
factory a minimum of 3 weeks prior to customer promise ship date.
For mounting a coupling (which must be balanced prior to receipt at the factory), WITHOUT finish bore and keyseat,
add $6932 list per motor. Unfinished coupling and outline drawings must be received at the factory a minimum
of 4 weeks prior to customer ship date.
14c TACHOMETER GENERATOR EQUIPMENT
Customer-supplied tachometers will not be tested. Drawings, installation instructions and parts list of customersupplied tachometers must be received at the factory a minimum of 3 weeks prior to customer ship date.
For pricing, refer to page 3.24, Item 29.
14d PAINT
Due to hazardous waste disposal regulations and VOC emissions requirements, GE will not accept orders using
customer-supplied paint. For special paint requirements needed to meet application and commercial needs,
contact GE.
15

DRAINS
Drain holes are normally selected to provide drainage of moisture that might collect at the lowest point of the
motor. Not available on CD180AT Frames. When drain holes are required, placement for horizontal and vertical
mount are as follows: Horizontal Mount (1) at each end, vertical CD210AT-CD320AT: (3) at lowest point, CD360AT
and above: (1) at lowest point.

15a TAPPED HOLE, add $430 list per motor. No adder required for Waterproof enclosures. (STD 1 at each end)
15b TAPPED HOLE WITH SOLID PLUG, add $430 list per motor. No adder required for Waterproof enclosures.
15c AUTOMATIC DRAIN BREATHER, add $510 list per motor.
Available on totally enclosed CD210AT-CD5010AY frames only. Not available on CD6000 frames.

3.12

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

Accessories &
Modifications
Accessories &
Modifications

Dripproof Fully Guarded Blower Ventilated
(DPFG-BV) (Shown above with filter)

Terms

16b SEPARATELY VENTILATED, FULLY GUARDED OR TOTALLY
ENCLOSED SEPARATELY VENTILATED (DPFG-SV) OR (TESV)
For applications where a contaminated atmosphere is
encountered, ventilating air is piped into the motor or
generator from an external source to the commutator end on
frames CDL182AT-CD5010AY and to the drive end on CD6000CD6900 frames. Openings have drilled and tapped holes for
convenient duct connection. Price does not include blower, pipe
or duct. See page ___ for separate ventilating air requirements.
Dripproof Fully Guarded, Separately-Ventilated (DPFG-SV)
Separately ventilated motors with recommended air supply are
(Frame CD366AT shown above with air inlet on top of motor
suitable for constant torque operation with allowable operating
commutator end. Other air inlet locations available.)
temperatures down to five percent base speed with most
power supplies. See application section page XX (was page
177) for motor heating limitations.
On separately ventilated, fully guarded motors, air is expelled into the surrounding environment through air
exhaust openings which are fully guarded.
For use of splashproof on separately ventilated, fully guarded motors, see page 3.14, Item 16c.
On totally enclosed separately ventilated motors, the ventilating air is ducted in and out of the motor and solid
covers are placed on all other air openings. The motor is then inherently splashproof, and the addition of the
splashproof modification to a totally enclosed separately ventilated motor is not necessary.
Note: CD180AT motors must have an 8 1/2" C-Face. Totally enclosed separately ventilated CD180AT frames in
hazardous locations are not available.

Outline
Dimensions

16a BLOWER VENTILATED, FULLY GUARDED (DPFG-BV)
For use on fully guarded motors where the application requires
extended periods of low-speed operation by armature voltage control
at full load torque. The amount of ventilating air is independent of
motor speed, allowing constant torque operation with safe operating
temperatures down to five percent rated speed with most power
supplies. See application section page XX (was page 177) for motor
heating limitations.
The standard blower motor is 230/460 Volt AC, 60 hertz and is
suitable for (but not nameplated for) 220-240/440-480 Volt AC,
60 hertz. Refer to GE for 50 hertz blowers and special blower
motor voltages.
Filters are optional for applications requiring protection against
particles in the air. For fine particles such as cast iron dust, a
blower and filter is not recommended. For these conditions,
totally enclosed construction or separate ventilation should be
considered. Blower filters on frames CD5010AY and below are
washable. Filters for frames CD6000-CD6900 are disposable.
For use of splashproof fully guarded on blower ventilated
motors, see page 3.14, Item 16d.

Motor Pricing

ENCLOSURES

Application
Information

16

DESCRIPTION

Other

ITEM

General
Information

CD180AT through CD6900

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.13

Accessories and Modifications

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

ITEM

DESCRIPTION

16c SPLASHPROOF FULLY GUARDED (SPFG) (FOR SEPARATELY VENTILATED OR SELF-VENTILATED FULLY
GUARDED MOTORS)
Provides for bolted-on splash covers to meet NEMA Standard MG-1-2009, Part 1.25.2. The covers are constructed to
prevent liquids and solid particles from entering in a straight line at any angle not greater than 60° from the vertical.
This does not apply to motors operated in a vertical position. For these applications, refer to GE.
For CD180AT frames, splashproof fully guarded, separately ventilated is only available when horizontally
mounted.
16d SPLASHPROOF FULLY GUARDED (FOR BLOWER VENTILATED, FULLY GUARDED MOTORS)
For splashproof fully guarded, blower ventilated, list price additions for Modifications a. and d. must both be
added.
Provides for bolted-on splash covers to meet NEMA Standard MG-1-2009, Part 1.25.2. The covers are constructed to
prevent liquids and solid particles from entering in a straight line at any angle not greater than 60° from the vertical.
In addition, on CD6000-CD6900 frames with a splashproof fully guarded, blower ventilated enclosures, splashproof
hoods are required to cover the blower air inlets. See page ___ for outline dimensions of frames CD6000-CD6900
with a splashproof, fully guarded blower ventilated enclosure.
This does not apply to motors operated in a vertical position. For these applications, refer to GE.
For CD180AT frames, splashproof fully guarded, blower ventilated is only available when horizontally mounted.
16e WATERPROOF (WP)
For use where motors are required to exclude water applied from a hose and for outdoor application. (Do not
use where ice may form on fan of TEFC motors or generators.) Waterproof features are not available in TEAAC
or TEWAC.
Standard waterproof features for frames CDL182AT-CD5010AY
(TEFC, TENV, and TEAO) include:
•  Spot faced surfaces on frame under the pole bolts
•  Washers under pole bolts
•  Drain holes at low point of machine
•  Polyurethane paint
•   Special neoprene-gasketed, heavy handhold covers with 
machined surfaces on cover and bearing bracket
•   Waterproof conduit box with tapped conduit entrance hole 
and machined mating surfaces (Not on CD180AT. On
CD180AT frames the conduit box is built into the endshield.)
Totally Enclosed Nonventilated Waterproof (TENV-WP)
•   Sealed frame fits and special treatment of all mating 
(Frame CD407ATY shown above)
surfaces
•   Lip type rubbing seals on both outboard bearings 
(where applicable)
•  Corrosion-resistant hardware

Terms

Space heaters are recommended for all waterproof motors.

3.14

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

MOTOR LIST PRICE
Up to
$2500

$2501 to $3593 to $5579 to $9749 to
$3592
$5578
$9748 $13218

$13219
to
$23922

$23923
to
$42136

$42137
to
$61750

$61751
to
$98628

$98629 $157704 $252289
$403651
to
to
to
and up
$157704 $252288 $403650

List Price Addition
a. Blower Ventilated
Motor-mounted blower with
filter: 230/460 V or 575V,
3Ph, 60 Hz
Motor-mounted blower
without filter: 230/460V
or 575V, 3Ph, 60 Hz
For 190/380V, 50 Hz Blower
Motors, add to blower
assembly (a) above
b. Separately ventilated, fully
guarded or enclosed
separately ventilated
c. Splashproof, fully guarded
(for use with self of
separately ventilated, fully
guarded machines)
d. Splashproof, fully guarded
(for use with blower
ventilated fully guarded
machines) Modification Item
a. must also be added for
splashproof, fully guarded,
blower ventilated
e. Waterproof
f. Dustproof (taconite dusts)

$1472

$1472

$1472

$2274

$2576

$2866

$3158

$3706

$4778

$13578

$16848

$28904

$28904

$1032

$1032

$1032

$1814

$1814

$2318

$2318

$3014

$4306

$7090

$8214

$12516

$12516

$208

$208

$208

$364

$364

$464

$464

$604

$862

$1418

$1644

$2504

$2504

For CDL182AT-CD5010AY and CD6000-CD6900 frames, NO PRICE ADDITION

$204

$204

$420

$636

$810

$810

$810

$810

$1216

$1216

$1216

$1216

$1620

$204

$312

$420

$636

$810

$810

$810

$810

$1216

$4086

$4086

$6762

$7368

$1502
$304

$1502
$340

$1658
$486

$2050
$756

$2520
$988

$3100
$620

$3810
$1570

$4710
$1700

$5780
$1970

Not Available
Not Available

Terms

Note: Items e. and f. apply to totally enclosed motors. Items b. and c. apply to splashproof fully guarded, separately ventilated motors. Items a.
and d. apply to splashproof fully guarded, blower ventilated motors.

Application
Information

ENCLOSURE

Accessories &
Modifications

16g TROPICAL PROTECTION
The standard Kinamatic motor is suitable for operation in tropical climates, where fungus and high humidity are
present, without price addition. Space heaters are recommended for motors to be used in environments where high
humidity is present. (See page 3.20, Item 26 for space heaters.)

Accessories &
Modifications

Motor Pricing

DUSTPROOF (DP) Applies to frames CDL182AT-CD5010AY with TEFC and TENV enclosures only.
For applications requiring protection against fine abrasive dust such as taconite. Price addition includes:
•  Metal labyrinth seal on drive end
•  Gasketed handhole covers
•  A sealed dust cap on the commutator end of TENV motors
•   A labyrinth seal on the commutator end of TEFC motors. For cement mill applications or for TEAAC or TEWAC 
motors, refer to GE.

Other

16f

DESCRIPTION

Outline
Dimensions

ITEM

General
Information

CD180AT through CD6900

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.15

Accessories and Modifications

ITEM
17

DESCRIPTION
ENDSHIELDS
Standard NEMA Type C-Face and Type D-Flange dimensions are shown on
the dimensions pages. Refer to GE for CD6000-CD6900 frames. Where oil
will be above the bottom of the horizontal shaft, including splashing or
spraying, a special shaft seal is required. (Refer to page 3.18, Item 22 for
shaft seal.)

17a Type C-Face Endshields are available on frames CD320AT and below.
NEMA does not specify C-Face dimensions for CD365AT-CD5010AY frames.
The desired C-Face dimensions must be approved by GE and specified with
the order.
17b Type D-Flange Endshields are available on frames CD5010AY and below.
Available on frame 5010AY if supported by feet.

NEMA Type C-Face Endshield

17c P-Base Adapters — NEMA does not specify P-Base dimensions for DC motors. The desired P-Base dimensions must
be approved by GE and specified with the order. The factory will use an adapter on a D-Flange (price included in
P-Base adder) to achieve desired dimensions. Apply adder from page 3.31, Item 33 for vertical mounting. If special
drive end shaft dimensions are required, see page 3.19, Item 24 for adder.
MOTOR FRAME SIZE
SPECIAL ENDSHIELDS

CD180AT

CD210AT

CD250AT

CD280AT

CD320AT

CD360AT

CD400AT

CD500AT

CD5010AY

List Price Addition
a. Type C-Face
b. Type D-Flange
c. P-Base Adapter

Outline
Dimensions

Accessories &
Modifications

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

$172†
$216
$648

$502
$964
$1928

$652
$1060
$2312

$846
$1706
$2774

$1100
$1282
$3328

‡

‡

‡

‡

$5356
$6652

$6644
$8636

$7308‡‡
$9500

$7308‡‡
$9500

†For CD180AT frames, please specify 4.5" or 8.5" C-Face.
‡Contact GE
‡‡On CD5010AY frames, motor must also be supported by feet.

Application
Information

The following chart details the standard endshield material used on Kinamatic motors. Non-standard Kinamatic
motors manufactured for special applications may not use standard endshield material. Refer to GE for nonstandard motors.
MOTOR FRAME SIZE
ENDSHIELD

CD180AT

CD210AT

CD250AT

CD280AT

CD320AT

CD360AT

CD400AT

CD500AT

CD5010AY

Other

STANDARD ENDSHIELD MATERIAL
a. Standard Drive End

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

b. C-Face Drive End

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

c. D-Flange Drive End

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

d. P-Base Drive End

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron
Fabricated
Steel
Fabricated
Steel
Fabricated
Steel

e. Commutator End

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Cast Iron

Not Available Not Available Not Available
Fabricated
Steel
Fabricated
Steel

Fabricated
Steel
Fabricated
Steel

Fabricated
Steel
Fabricated
Steel

Cast Iron

Cast Iron

Cast Iron

Terms

Price addition for fabricated steel (per endshield) is as follows:

3.16

Motor Frame Size

List Price Addition

CD210AT-CD320AT
CD360AT
CD400AT
CD5010AY

$2412
$3600
$4268
$4826

www.gemotors.com

•

800-541-7191

Ductile Iron

Fabricated steel is available.

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

19

CD250CD320

CD365CD409

CD504CD5010

CD6000CD6100

CD6200

CD6700

CD6800

CD6900

Net Price

$400

$600

$800

$1000

$1400

$2000

$2500

$3000

$3700

GREASE AND FITTINGS

19a GREASE
The following greases are available:
Standard (Alvania® #2) or equivalent. Suitable for 15°F (-10°C) to 212°F (100°C) ambient temperature.
No price addition.
Low Temperature (Shell Aeroshell® #7) or equivalent. Suitable for -60°F (-51°C) to 200°F (93°C) ambient temperature.
Add $172 list per motor.
High Temperature (Mobil Polyrex EM®) or equivalent. Suitable for -20°F (-28°C) to 350°F (176°C) ambient
temperature.
Add $172 list per motor.
19b FITTINGS
Grease fittings — Not necessary on frames CDL182AT-CD2110AT because prelubricated and shielded bearings are
standard. On CD258AT-CD5010AY and CD6000-CD6900 frames, zerk grease fittings are standard. When grease
fittings are required, open ball bearings and bearing caps are included. (Not available on CD180 frames.)
No price addition.
For re-greaseable bearings with standard alemite grease fittings on CD218AT-CD2110AT, add $516 list per motor.
For special grease fittings, button head, pin head or other than standard, add $172 list per motor.
Pressure Relief Valve add $172 list per motor.

Percent Base Speed

Occasionally Repeated Loads

Frequently Repeated Loads

100%
200%
300% or greater

150%
150%
140%

140%
130%
125%

Application
Information

CURRENT OVERLOAD — MAXIMUM LOAD AT BASE SPEED
In accordance with NEMA standards, continuous rated industrial DC motors rated 3/4 HP/RPM and less shall
be capable of occasionally repeated loads of 150% of the base speed full load current at all speeds within the
standard speed ranges listed on pages __-__. Although NEMA does not specify frequently repeated load
capability, DC motors in these ratings are capable of 140%. For motors larger than 3/4 HP/RPM, the following
load capability applies:

Other

20

For occasionally repeated load capability of 200% with a frequency repeated load capability of 175% on motors
rated 3/4 HP/RPM and less with standard speed ranges listed on pages __-__ and on motors rated larger than
3/4 HP/RPM at base speed only, add 10% and refer to GE for effect on frame size.
Occasionally repeated loads are defined as one-minute duration or less and are not considered as part of the
regular duty cycle. Occasionally repeated loads are considered as commutation limits rather than heating limits.
Frequently repeated loads are defined as one-minute duration or less repeated such that the RMS current does not
exceed rated current over any five-minute period.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Motor Pricing

CD182CD2110

Accessories &
Modifications

FRAME SIZE
Export Boxing

Accessories &
Modifications

EXPORT BOXING
The price for export boxing is a NET PRICE adder applied to the total price of the motor after adjusting for all
modifications. Export boxing must be specified at the time of order.

Outline
Dimensions

18

DESCRIPTION

3.17

Terms

ITEM

General
Information

CD180AT through CD6900

Accessories and Modifications

ITEM

DESCRIPTION

21

PUMP MOTORS
DC Motors with armature voltages from 105-130 Volts in most cases are used in pump applications. These are
special motors built to pump manufacturer specifications. Because of the low armature voltage these motors
have special electrical designs and in many cases frame sizes are larger than standard. If a model number is not
available, a request for motors in this voltage range must be accompanied by the following information.
Pump motors operated from DC potential busses or batteries will show significant speed variations from nominal
when the motor is cold and when the applied voltage varies below nominal.
Typically Motor RPM will be lower than nameplate speed (approx. 10-15%) when cold and increase to nameplate
RPM as main field reaches operating temperature. To reduce the cold to hot speed variations, the shunt fields
should be energized at 50-70% of rated voltage to stabilize. However, for ‘emergency’ pump motor applications,
where field pre-heating may not be feasible, the pump capacity must be sized to the cold start RPM.
Also, at lower than nominal voltage the motor will run slower than nameplate RPM, while conversely the motor will
run higher than nameplate RPM when voltage is higher than nominal.
For Pump Motor quotations, contact GE.

22

SEALS, DRIVE END SHAFT (horizontal or vertical with shaft up or down)
GE offers the following shaft seals: Lip type rubbing seals (which provide protection against oil mist or splash),
labyrinth seals (which provide protection against fine abrasive dust), and Inpro® seals (which provide protection
from liquids, solids, steam, and slurries of all types). Price addition (per seal) is as follows:
Note: For availability and pricing of commutator end shaft seals, refer to GE.

Outline
Dimensions

Accessories &
Modifications

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

Motor Frame Size

Lip Seal

Labyrinth Seal

Inpro® Seal

CD180AT-CD210AT
CD250AT-CD320AT
CD360AT-CD5010AY
CD6000-CD6200
CD6700-CD6900

$298
$420
$596
Not Available
Not Available

$298
$490
$838
$1138
$1394

Not Available
$2442
$3736
$6900
$8912

23

SEVERE MECHANICAL “A”
Severe mechanical duty “A” features are used on applications where motors are subject to severe torsional loads
(severe transients, rapid reversals), where additional strength of components is required to resist high
electromagnetic forces.
Severe mechanical duty “A” features include:
•  Solid or pinned, laminated commutating poles
•   High-strength (grade 8) bolts on both main poles and commutating poles; A black oxide finish on these bolts 
prevents the possibility of hydrogen embrittlement.
•  The magnet frame is spotfaced for firm seating of these high strength bolts. 
•  Cables are securely anchored with extra lead tying.
•   Bolted connections at commutating coils and series coils are insulated to prevent chafing of leads that come in 
contact with those connections.
•  A cable clamp is used in the conduit box.
•  A molded insert is located in the lead exit hole to protect leads from threads and other sharp corners.
•   For CD360AT, CD400AT, CD504AT-CD508AT, high-strength armature banding and epoxy RHP armature varnish 
is used.

Terms

Other

Application
Information

Inpro® is a registered trademark of Inpro/Seal Inc., Rock Island, Illinois

3.18

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

Duty “A”
Not Available
$892
$1136
$1403
$1631
Not Available
$2123
$2645
$4439
Not Available
Refer to GE

Accessories &
Modifications

Motor Frame Size
CDL182AT-CD189AT
CD218AT-CD2110AT
CD258AT-CD259AT
CD287AT-CD288AT
CD327AT-CD328AT*
CD329AT
CD365AT-CD368AT
CD407AT-CD409AT
CD504AT-CD508AT
CD5010AY
CD6000-CD6900

Motor Pricing

List Price Addition

* Subject to engineering approval

24

SHAFT EXTENSIONS

24a Standard Single Shaft Extension. Dimensions will be as shown on dimension prints.
24b Standard Double Shaft Extension. Dimensions will be as shown on dimension prints.
24c Standard Oversize Single Drive End Shaft Extension. Standard shaft extension of the next larger frame diameter
for CD210AT-CD360AT. Oversize shafts are not available on Explosionproof Motors. See table in Item 24d for
CD400AT and CD500AT frames. On CD5010AY frame, the standard drive end shaft is oversize (4.125 in. dia.), no
price addition. For overhung loads, refer to GE. Where standard oversize shaft is used, oversize bearing will also be
used (already included in price adder). Use prices listed below.
24d Standard Oversize Double Shaft Extension. Standard double shaft extension of the next larger frame diameter for
CD210AT-CD360AT. Oversize shafts are not available on Explosionproof Motors. For overhung loads, refer to GE.
Oversize shafts for CD400AT-CD500AT are as follows:

CD400AT
CD504AT-CD508AT

Commutator End

Drive End

2.625
3.25

2.875
3.75

Application
Information

OVERSIZE SHAFT DIAMETER (inches)

Frame

No additional oversize shaft available.
See dimension prints for standard shaft.

CD5010AY

Accessories &
Modifications

23
Cont’d

DESCRIPTION

Outline
Dimensions

ITEM

General
Information

CD180AT through CD6900

CAUTION:
Belted drives using smaller than standard diameter shafts and/or longer than standard shafts must be referred to
GE with complete belt drive data.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.19

Terms

24e Shaft Extension, Special. Special straight extensions on drive end or commutator end or both. The desired
dimension must be specified when ordered. The special diameter must not exceed the oversize diameter where an
oversize shaft is available.
On CD6000 frame the special shaft diameter must not exceed the standard shaft diameter.
If required, pricing for oversize bearing must also be added.

Other

Note: With oversize shafts, the shaft length may be longer and the overall machine length may be longer. Refer to
GE for exact dimensions.

Accessories and Modifications

ITEM

DESCRIPTION

24e
Cont’d

MOTOR LIST PRICE

Motor Pricing

General
Information

CD180AT through CD6900

SHAFT EXTENSION

a. Standard Single
Shaft Extension

Accessories &
Modifications

b. Standard Double
Shaft Extension

$13219
to
$23922

$23923
to
$42136

$42137
to
$61750

$61751 $98629 $157704 $252289
$403651
to
to
to
to
and up
$98628 $157704 $252288 $403650

25

26

Furnished as standard on all motors and generators.
No price addition for larger frame size generators where double shaft is standard.
$70

$82

$96

$150

$244

$352

$420

$594

$676

On CD6000-CD6900,
no adder required

c. Standard
Oversize Single
Drive End Shaft
Extension

Not available on
CD180AT frames.

$366

$468

$574

$680

$766

$892

Not available on
CD6000-CD6900 frames.

d. Standard
Oversize Double
Shaft Extension

Not available on
CD180AT frames.

$732

$936

$1148

$1360

$1532

$1782

Not available on
CD6000-CD6900 frames.

$488

$680

$788

$972

$1272

$1784

e. Shaft Extension,
Special

Outline
Dimensions

Accessories &
Modifications

$2501 to $3593 to $5579 to $9749 to
$3592
$5578
$9748 $13218

List Price Addition

$488

$488

$488

$2520

$2520

3.20

$5040

$5040

SHAFT GROUNDING BRUSH
A shaft grounding brush is recommended to minimize possible bearing failures caused by shaft voltages. It is
mounted externally on the drive end of CD218AT-CD5010AY frames (which reduces usable drive end shaft length
by approximately 1 inch) and is mounted internally on the drive end of CD6000-CD6900 frames.
Note: The shaft grounding brush and labyrinth seal are furnished as standard with papermill features.
Motor Frame Size

List Price Addition

CD180AT
CD210AT
CD250AT-CD320AT
CD360AT-CD5010AY
CD6000-CD6900

Not Available
$1448
$1676
$2024
$1186

N/A on C-face, D-flange or P-base motors. Use TACH options. Price addition
includes labyrinth seal on CD218AT-CD5010AY frames. See page 3.18, Item 22
for labyrinth seal on CD6000-CD6900 frames.

SPACE HEATERS
Note: Furnished as standard with crane duty feature
Space heaters are installed inside the machine with leads brought out through the standard conduit box. Single
phase AC and DC ratings available are 120, 240, and 480 Volts on frames CD180AT-CD6900. Refer to GE for higher
voltage.
Motor Frame Size

Wattage

List Price Addition

CD180AT-CD210AT
CD250AT-CD320AT
CD365AT-CD5010AY
CD6000-CD6100
CD6200-CD6900

30
75
180
500
1000

$582
$582
$582
$1658
$1658

Terms

Other

Application
Information

Up to
$2500

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

DESCRIPTION

27

SPEED LIMIT DEVICE
Provides for addition of calibrated speed limit device (non-adjustable on frames CD508AT and below and adjustable
on frames CD5010AY and above) for motor over speed protection when connected in proper circuit. The device is
flange mounted on the commutator end of the motor. Contact will be normally closed on frames CD508AT and
below. On frames CD5010AY and above, both normally open and normally closed contacts are provided. The device
will be set at the factory to operate at 13-17% above the top rated speed. For special limiting speed, refer to GE.
Note: Non-adjustable speed limit devices are not recommended for crane duty use. If adjustable speed limit
switch is required on frames CDL182AT-CD508AT, refer to GE.

CD182AT-CD508AT

CD5010AY-CD6900

List Price Addition
a. Speed limit device (mounted)

$2534

$5982

b. Speed limit device (mounted)
with double shaft extension

Refer to GE

$5982

$7646

$8480

c. Euclid speed switch

Terms

Other

Application
Information

Outline
Dimensions

Speed Limit Devices are available on all frames with
a single or double shaft extension. (Frame CD5010AY
shown above with double shaft extension.)

Accessories &
Modifications

SPEED LIMIT DEVICE

Accessories &
Modifications

MOTOR FRAME SIZE

Motor Pricing

ITEM

General
Information

CD180AT through CD6900

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.21

Accessories and Modifications

ITEM

DESCRIPTION

28

SPEED RANGE GREATER THAN STANDARD BY FIELD CONTROL*
Provides for increased speed range by field control with constant horsepower output. For top speeds not listed, use
the price of the next higher top speed listed. The frame size may be different from standard. On single phase
power supply, refer to GE. The overloads to these speeds are defined in page 3.17, Item 20.
All Voltages, Continuous or Short Time Rated Dripproof Fully Guarded and Totally Enclosed

Motor Pricing

General
Information

CD180AT through CD6900

Accessories &
Modifications

Base
Speed
RPM

Rated
Top
Speed
RPM

HORSEPOWER
3 and
Below

5

7.5

10
10
10
10
15
0
10
10
10
15
15
15
0
10
10
10
15
10
10
10
15
10
15
15
15
10
15
15
10
10
15
20
10
15
15

10
10
10
10
15
0
10
10
10
15
15
20
0
10
10
10
20
10
10
10
15
10
15
15
15
10
15
15
10
10
15
20
10
15
15

10
10
10
10
15
0
10
10
10
15
15
20
0
10
15
15
20
10
10
10
15
10
15
15
15
10
15
15
10
15
20
20
10
15
15

10

15

20

25

30

40

50

60

75

100

125

150

200

250

10
15
15
20
0
10
15
20
20
25

10
15
15

15
20
20

15
20
20

15
20

15

0
10
15
20

0
15
20

0
15
20

10
15
20

10
15

PERCENTAGE ADDITION TO LIST PRICE OF BASIC MOTOR
2500

Accessories &
Modifications

1750

1500

Outline
Dimensions

1150

850

Application
Information

650

500

400

Other

300

Terms

250

3500
2500
2900
3000
3500
1900
2300
2600
2900
3100
3200
3400
2000
2300
2550
2900
3450
2000
2200
2550
3400
2000
2200
2550
2600
2000
2200
2500
1600
1900
2200
2400
1200
1500
1800
800
900
1000
1100
1200
1250
1300
1350
1400
1500

10
10
10
10
15
0
10
10
10
15
15
20
0
10
15
15
20
10
10
10
15
10
15
15
15
10
15
15
10
15
20
20
10
15
15

10
10
10
10
15
0
10
10
10
15
15
20
0
10
15
15
20
10
15
15
15
10
15
15
15
10
15
15
10
15
20
20
10
15
15

10
10
10
10
15
0
10
10
15
15
20
20
0
10
15
15
20
10
15
15
20
10
15
15
15
10
15
15
10
15
20
20
10
15
15

10
10
10
10
15
0
10
10
15
15
20
20
0
10
15
15
20
10
15
15
20
10
15
15
15
10
15
15
10
15
20
20
10
15
15

Refer to Factory

10
10
10
10
15
0
10
10
15
15
20
20
0
10
15
15
25
10
15
15
20
10
15
15
15
10
15
15
10
15
20
20
10
15
15

10
10
10
10
20
0
10
15
15
20
25

15
10
15
15
20
0
10
15
15
20
25

20
10
15
15
20
0
10
15
20
20
25

0
10
15
15
25
10
15
15
25
10
15
20
20
10
15
15
10
15
20
20
10
15
20

0
10
15
15
25
10
15
15
25
10
15
20

0
10
20
20
25
10
15
15
25
10
15
20

0
10
20
20
25
10
15
20

0
15
20
20

0
15
20
20

0
15
20

10
20
20

10
20
20

10
15
20

10
15
20

10
15
20

15
15
20

15
15

10
15
20

10
15
20

15
15
20

15
15
20

15
15
20

15
15

10
15
15
10
15
20
20
10
15
20

10
15
15
10
15
20
20
10
15
20
2
2
4
6
8
10
12.5
15
17.5
20

10
15
15
10
15
20
20
10
15
20
2
2
4
6
8
10
12.5
15
17.5
20

15
15
15
10
15
20

15
15
20
10
15
20

15
20

15
20

20
20

10
15
20

15
20
25

15
20

10
15
20
2
2
4
6
8
10
12.5
15
17.5
20

10
15
20
2
2
4
6
8
10
12.5
15
17.5
20

10
15
20
2
2
4
6
8
10
12.5
15
17.5
20

10
15
20
2
2
4
6
8
10
12.5
15
17.5
20

10
15
20
2
2
4
6
8
10
12.5
15
17.5
20

* Contact GE for design verification (affected by ambient, overload, Class B rise, etc.)

3.22

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

DESCRIPTION

28a SPEED RANGE GREATER THAN STANDARD BY FIELD CONTROL
Provides for increased speed range by field control with constant horsepower output. For top speeds not listed, use
the price of the next higher top speed listed. The frame size may be different from standard. On single-phase
power supply, refer to GE. The overloads to these speeds are defined in page 3.17, Item 20.
All Voltages, Continuous or Short Time Rated Dripproof Fully Guarded and Totally Enclosed
HORSEPOWER

850

650

500

www.gemotors.com

0
10
10
0
10
15
15
15
20
0
0
6
8
12.5
15
17.5
17.5
20
0
4
8
10
12.5
15
17.5
17.5
0
0
4
10
10
12.5
15
17.5
0
0
0
0
4
6
12.5
15
15
17.5
20

•

0
10
10
0
10
15
15

0
10
10
6
10
15
15

0
4
6
8
12.5
15
17.5
17.5

0
4
6
8
12.5
15
17.5
17.5

0
6
8
10
12.5
15
17.5
20
0
4
6
10
12.5
15

4
8
10
12.5
15
17.5
20

0
0
0
4
6
10
12.5
15
17.5

800-541-7191

4
6
10
12.5

400

300

250

1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
750
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
710
750
800
900
1000
1100
1200
1250
1300
1350
1400
1500

300

400

500

PERCENTAGE
ADDITION TO LIST PRICE
OF BASIC MOTOR
0
0
0
6
10
12.5
15
15
17.5
20
0
0
4
6
10
12.5
12.5
17.5
20
22.5
22.5
0
0
2
2
4
6
10
12.5
15
17.5
17.5
20

0
4
4
6
10
12.5
15
17.5
20

0
4
6
8
12.5
15
17.5
20
22.5

0
4
4
6
10
12.5
17.5
20

0
4
4
8
12.5
17.5
20
22.5

0
1
2
2
6
10
15
17.5
17.5
20
20
22.5

0
1
2
4
8
12.5
17.5
17.5
17.5
20
22.5
25

Accessories &
Modifications

1900
2000
2200
1800
1900
2000
2100
2200
2300
1500
1600
1700
1800
1900
2000
2100
2200
2300
1500
1600
1700
1800
1900
2000
2100
2200
1400
1500
1600
1700
1800
1900
2000
2100
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000

Rated
Top Speed
RPM

Accessories &
Modifications

PERCENTAGE
ADDITION TO LIST PRICE
OF BASIC MOTOR

Base Speed
RPM

Outline
Dimensions

1150

500

Application
Information

1500

400

Other

1750

300

Rated
Top Speed
RPM

0
4
4
6
8
12.5
15
17.5
20

GEP387M 09/11 • Prices and data subject to change without notice.

Terms

Base Speed
RPM

HORSEPOWER

Motor Pricing

ITEM

General
Information

CD180AT through CD6900

3.23

Accessories and Modifications

ITEM
29

DESCRIPTION
TACHOMETER GENERATOR EQUIPMENT
SPEED RANGES
The following tachometer generator operating speeds are available with listed items:

Motor Pricing

General
Information

CD180AT through CD6900

Type
BC42

Accessories &
Modifications

BC46
Form Y

Accessories &
Modifications

AN-AC

Tachometer Output

Operating Range

50 Volts/1000 RPM
100 Volts/1000 RPM
50 Volts/1000 RPM
100 Volts/1000 RPM
200 Volts/1000 RPM
50 Volts/1000 RPM
100 Volts/1000 RPM
90 Volts/1000 RPM

100-5000 RPM
100-2750 RPM
100-5000 RPM
100-3600 RPM
100-1800 RPM
100-5000 RPM
100-2500 RPM
100-5000 RPM

PY tachometers provide a medium
accuracy DC output for use with a
regulated drive or for speed
indication.

AN Series tachometers provide a compact construction
with thru-shaft capabilities. The AN Series tachometers
can be furnished with either AC or digital output signal
for speed regulation or speed indication. (Type AN-DG
tachometer shown above.)

Terms

Other

Application
Information

Outline
Dimensions

BC tachometers produce DC output
to provide high accuracy speed
regulation or speed indication.

3.24

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

ITEM

General
Information

CD180AT through CD6900

DESCRIPTION

29
Cont’d

MOTOR FRAME SIZE
MOTOR MOUNTED, DIRECT CONNECTED TACHOMETERS

CDL182AT-CD5010AY

CD6000-CD6900

Motor Pricing

List Price Addition

Accessories &
Modifications

OUTLINE PAGE ___

TYPE BC
A DC tachometer for high accuracy speed-indicating and/or speed-regulating applications.
The tachometer generator is flange mounted, rabbeted to the commutator endshield, and
is coupled with an antibacklash coupling to the motor shaft extension. The BC tachometer
generators will have a footed frame and commutator end extension covered by a thimble.
This allows belt driving a second tachometer mounted on the BC feet and simplifies customer
tachometer standardization. Any other arrangement should be referred to GE.
Note: A double shaft extension is not available on severe duty or explosion proof BC
tachometers.
Type BC
BC42, 50 or 100 Volts/1000 RPM
BC46, 50, 100 or 200 Volts/1000 RPM

$7440
$10008

$8333
$11209

$8194
$10728

$9117
$11562

BC42, 50 or 100 Volts/1000 RPM

$10400

$11645

Mounting kit is assembled to motor and is only for flange mounted BC
tachometer. (This includes coupling, stub shaft, and mounting bracket for BC tach.)
For explosionproof tachometer to be mounted on explosionproof motor,
refer to page ___.

$1666

$2500

BC42, 100 Volts/1000 RPM
BC46, 100 Volts/1000 RPM

Accessories &
Modifications

Type BC, Waterproof or Dustproof

5PY59JY, 50 or 100 Volts/1000 RPM (max speed 2500 RPM)

$4925

$5516

Mounting kit is assembled to motor and is only for flange mounted PY
tachometer. (This includes coupling, stub shaft, and mounting bracket for Form Y.)

$1666

$2500

Application
Information

OUTLINE PAGE ___

FORM Y, DC
A DC tachometer for medium accuracy speed-indicating and/or speed-regulating
applications. The tachometer generator is flange mounted and rabbeted to the
commutator endshield, and is coupled with an antibacklash coupling to the motor shaft
extension. (Not available as waterproof.)

OUTLINE PAGE ___

$1784

$4222

Other

TYPE AN-AC
An AC tachometer for medium accuracy speed-indicating or for use with some speedregulating systems. The tachometer generator is flange mounted and rabbeted to the
commutator endshield. (Not available for separate mounting or belt connection.)
45/90 Volts/1000 RPM
(For frames CD180AT-CD6200 only, including CD180AT and CD210AT
TEFC enclosures.)

Outline
Dimensions

Type BC, Explosionproof
(Class I, Group D, Class II, Groups E, F, G)

CD180AT and CD210AT TEFC motors suitable only for AN tachometer mounting on commutator end.

Terms

Not available on CD6700-CD6900.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.25

Accessories and Modifications

ITEM
29
Cont’d

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

DESCRIPTION
MOTOR MOUNTED, DIRECT CONNECTED TACHOMETERS

List Price Addition

Avtron AV85 THIN-LINE II™
(Replaces M85)
Style tachometer/encoder. Mounts on 8.8" accessory flange. No 
bearings, couplings, or adapters. Magnetoresistive (MR) sensors,
Wide-Gap technology, full wiring protection and LED diagnostics.

OUTLINE PAGE ___

Accessories &
Modifications
Outline
Dimensions

Environmental Rating

240, 600, 1024, 1200 pulses/revolution, single output

$3285

$5805

240, 600, 1024, 1200 pulses/revolution, dual output

$5468

$7988

2000, 2048, 4096, 5000 pulses/revolution, single output

$3641

$6156

2000, 2048, 4096, 5000 pulses/revolution, dual output

$6174

$8690

OUTLINE PAGE ___

240, 600, 1024, 1200 pulses/revolution, single output

$5945

$5945

240, 600, 1024, 1200 pulses/revolution, dual output

$8721

$8721

2000, 2048, 4096, 5000 pulses/revolution, single output

$6080

$6080

2000, 2048, 4096, 5000 pulses/revolution, dual output

$9000

$9000

TYPE AN-DG
Avtron AV850 SMART Tach II™
(Replaces AN-DG, M193B, M285)
Mounts on 8.5" accessory flange. No bearings, couplings or 
adapters. MR sensors, Wide-Gap technology, full wiring protection
and LED diagnostics. Removable sensors. Shaft grounding brush
option or permits thru-shafts up to 4.5"

Application
Information

CD6000

MODEL NUMBER AND DESCRIPTION

Avtron AV485 SMART Tach II™
(Replaces M3 and M4 solid-shaft, M385, M485, M785)
Style tachometer/encoder. NEMA 56C motor face mount (like BC).
MR sensors, full wiring protection and LED diagnostics, removable
sensors.

Heavy Duty
Industrial Applications
with frequent exposure to
temperatures variations
and contamination.
Paper, metals processing, plastics,
textiles, food, petrochemical,
machine tool, marine duty,
material handling
Severe Duty
Industrial Applications
with constant exposure to
temperature variations and
contamination, and increased
physical demands occur.
Paper, primary metals, petrochemical, mining, dockside cranes,
marine duty, wash down; 
Ideal for MD style motors.

OUTLINE PAGE ___

240, 600, 1024, 1200 pulses/revolution, single output

$4824

$6480

240, 600, 1024, 1200 pulses/revolution, dual output

$7034

$8690

2000, 2048, 4096, 5000 pulses/revolution, single output

$4959

$6620

2000, 2048, 4096, 5000 pulses/revolution, dual output

$7308

$8969

Add shaft grounding brush to AV850

$878

$2534

Avtron AV685 SMART Tach II™
(Replaces M685)
Mounts on stub shaft (tethered). MR sensors, full wiring protection
and LED diagnostics, removable sensors.

Other

MOTOR FRAME SIZE
CD180AT-CD5010AY

OUTLINE PAGE ___

240, 600, 1024, 1200 pulses/revolution, single output

$6881

$6881

240, 600, 1024, 1200 pulses/revolution, dual output

$9338

$9338

2000, 2048, 4096, 5000 pulses/revolution, single output

$7187

$7187

2000, 2048, 4096, 5000 pulses/revolution, dual output

$9950

$9950

Add shaft grounding brush to AV685

$1319

$1319

Heavy Duty
Industrial Applications
with frequent exposure to
temperatures variations
and contamination.
Paper, metals processing, plastics,
textiles, food, petrochemical,
machine tool, marine duty,
material handling.

Severe Duty
Industrial Applications
with constant exposure to
temperature variations and
contamination and increased
physical demands occur.
Paper, primary metals, petrochemical, mining, dockside cranes,
marine duty, wash down.
Ideal for MD style motors.

Terms

Notes:
Avtron AV850 SMART Tach II™ can not be mounted on CD250AT-CD320AT frames with a TEFC enclosure. Use a TENV or TEAO enclosure.
Avtron AV850, AV485 can not be mounted on CD180AT and CD210AT TEFC motors. Use a TENV enclosure.
Integral end of shaft grounding brush, add $2232 list to the above prices. Not available on tachs with thru shafts.
(ppr) pulses per revolution, required at time of order

3.26

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

MOTOR FRAME SIZE
CD6000

OUTLINE PAGE ___

Environmental Rating

240, 512, 600, 1024, 1200 pulses/revolution, single output

$4229

$4829

240, 512, 600, 1024, 1200 pulses/revolution, dual output

$5227

$5899

Northstar RIM Tach™ 6200
Foot mount or accessory bracket 56 C-face mount (mounts same
as BC style tachs). Magnetoresistive sensors, ductile iron enclosure,
polymer rotor, industrial connector, extra severe duty bearings for
long life. The RIM Tach 6200 is a close coupled design. Features
replaceable sensor modules.

OUTLINE PAGE ___

240, 512, 600 pulses/revolution, single output

$4219

$4852

240, 512, 600 pulses/revolution, dual output

$5218

$6001

1024, 1200 pulses/revolution, single output

$4944

$5686

1024, 1200 pulses/revolution, dual output

$5942

$6834

2048 pulses/revolution, single output

$5251

$6039

2048 pulses/revolution, dual output

$6250

$7188

Northstar RIM Tach™ 1250
Mounts on 12.5" accessory flange. No bearings, couplings, or 
adapters needed. Magnetoresistive sensors, ductile iron enclosure,
polymer rotor and industrial connector. For a through shaft or end
of shaft mountings the RIM Tach 1250 can fit up to a 8.0" diameter 
shaft. Features replaceable sensor modules. Used on CD6000’s.

Motor Pricing

List Price Addition

Northstar RIM Tach™ RT8
(Replaces RIM 8500)
Mounts on 8.5" accessory flange. No bearings, couplings, or 
adapters needed. Magnetoresistive sensors, ductile iron enclosure,
polymer rotor and industrial connector. For through shaft or end
of shaft mountings, the RIMTach RT8 can fit up to a 4.5" diameter 
shaft. Features replaceable sensor modules.

Mill Duty
Industrial Applications with
temperatures between -40ºC
and +80ºC, chemical resistance
include salt spray, most solvents,
mild acids and bases.
Paper, metal finishing, plastics,
textiles, converting, machine
tools, material handling.

OUTLINE PAGE ___

240, 512, 600, 1024, 1200 pulses/revolution, single output

N/A

$5554

240, 512, 600, 1024, 1200 pulses/revolution, dual output

N/A

$6557

2048 pulses/revolution, single output

N/A

$9994

2048 pulses/revolution, dual output

N/A

$10992

Mill Duty
Industrial Applications with
temperatures between -40ºC
and +80ºC, chemical resistance
include salt spray, most solvents,
mild acids and bases.
Paper, metal finishing, plastics,
textiles, converting, machine
tools, material handling.

Other

Notes:
Northstar RIM Tach™ RT8 can not be mounted on CD180AT-CD320AT frames with a TEFC enclosure. Use a TENV or TEAO enclosure.
The Northstar RIM 1250, 6200 and SLIM Tach™ SL85 and HS56 all have sealed electronics to prevent contaminant intrusion.
Shaft grounding brush, add $2232 list to the above prices.
All items listed above are CE approved.
(ppr) pulses per revolution, required at time of order

Accessories &
Modifications

MODEL NUMBER AND DESCRIPTION

Accessories &
Modifications

CD180AT-CD5010AY

Outline
Dimensions

MOTOR MOUNTED, DIRECT CONNECTED TACHOMETERS

Terms

29
Cont’d

DESCRIPTION

Application
Information

ITEM

General
Information

CD180AT through CD6900

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.27

Accessories and Modifications

ITEM
29
Cont’d

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

DESCRIPTION
MOTOR MOUNTED, DIRECT CONNECTED TACHOMETERS

Accessories &
Modifications

CD6000

MODEL NUMBER AND DESCRIPTION

List Price Addition

Northstar SLIM Tach™ SL85 (formerly LakeShore)
Mounts on 8.5" accessory flange. No bearings, couplings, or 
adapters needed. Magnetoresistive sensors, ductile iron enclosure,
polymer rotor and industrial connector. For through shaft or end of
shaft mountings, the SLIM Tach SL85 can fit up to a 3.75" diameter 
shaft. Approx. half the thickness of the RIM 8500. The SL85 does not
have replaceable sensor modules. Through shaft models are also
available for shafts ranging from .5" through 3.75" in diameter.

OUTLINE PAGE ___

Environmental Rating

64, 128, 256, 512, 1024 pulses/revolution, single output

$2362

N/A

64, 128, 256, 512, 1024 pulses/revolution, dual output

$4061

N/A

2048 pulses/revolution, single output

$2530

N/A

Northstar SLIM Tach™ HS56 (formerly LakeShore)
Hollow shaft design allows for mounting when an accessory flange
is not available. Mounts on a standard shaft extension or stub shaft.
Magnetoresistive sensors, polymer rotor and industrial connector.
SLIM Tach HS56 can fit up to a 1.125" diameter shaft.

Outline
Dimensions

MOTOR FRAME SIZE
CD180AT-CD5010AY

Heavy Industrial
Industrial Applications with
temperatures between -40°C and
+80°C, chemical resistance include
salt spray, most solvents, mild
acids and bases.
SL85 can be used in a Mill Duty
environment.

OUTLINE PAGE ___

64, 128, 256, 512, 1024 pulses/revolution, single output

$2606

$2867

64, 128, 256, 512, 1024 pulses/revolution, dual output

$3821

$4203

2048 pulses/revolution, single output

$2770

$3048

2048 pulses/revolution, dual output

$4152

$4567

Industrial Duty
Industrial Applications with
temperatures between
-20°C and +80°C, chemical
resistance include salt spray,
most solvents, mild acids
and bases.

Notes:
Northstar RIM Tach™ RT8 can not be mounted on CD180AT-CD320AT frames with a TEFC enclosure. Use a TENV or TEAO enclosure.
The Northstar RIM 1250, 6200 and SLIM Tach™ SL85 and HS56 all have sealed electronics to prevent contaminant intrusion.
Shaft grounding brush, add $2232 list to the above prices.
All items listed above are CE approved.
(ppr) pulses per revolution, required at time of order

Application
Information

Dynapar HA625 Encoder
Flange mounted Tach, 5-26 VDC input, push-pull and differential
line driver, 5-26 VDC, single output, NEMA 4/IP66 sealed enclosure,
side mount MS style connector (10 pin mating connector included)
over voltage protection, output short circuit protection, and reverse
voltage protection, 85°C operating temperature, CE labeled.
240, 512, 600, 1024, 1200, 2048 pulses/revolution

Heavy Industrial
Industrial Applications with
temperatures between
40°C and +80°C.
$1392

Dynapar H56 Rotopulser
(Replaces the 62P)
56C face mounted tach (mounts same as BC series tachs). Heavy
mill duty enclosure, 5-26 VDC input, push-pull and differential line
driver, 5-26 VDC, single output, pluggable screw terminals
(Industrial connectors) mating connector(s) included.

Other

OUTLINE PAGE ___

$1532

OUTLINE PAGE ___

240, 512, 600, 1024, 1200, 2048 pulses/revolution, single output

$3536

$3890

240, 512, 600, 1024, 1200, 2048 pulses/revolution, dual output

$3951

$4346

Heavy Mill Duty
Industrial Applications with
temperatures between -40°C and
+80°C NEMA 4/IP66 enclosure.
Suitable for severe duty in paper,
steel and lumber mills.

Terms

Notes:
The HA625, H56 and X25 require a Tach mounting kit. (Tach mounting kit consists of Tach adapter, coupling and stub shaft). The H56 can also be foot mounted.
The HA625, H56 and X25 can not be mounted on CD180-CD210 TEFC motors. Use TENV enclosure.
(ppr) pulses per revolution, required at time of order

3.28

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

MOTOR FRAME SIZE
CD6000

MODEL NUMBER AND DESCRIPTION

List Price Addition

Dynapar HS35R Sealed Hollow Shaft
Hollow shaft encoder is designed for easy installation onto the
motor, the unit sealed as well as equipped with an unbreakable disk
that meets the demands of the most severe shake and vibration,
the unit is electrically and thermally isolated, shaft seals at both
ends, dust cover included. 5-26 VDC input, push-pull and differential
line driver, 5-26 VDC output.

OUTLINE PAGE ___

240, 512, 600, 1024, 1200, 2048 pulses/revolution

Industrial
Industrial Applications with
temperatures between
-40°C and +70°C
$1200

Accessories &
Modifications

240, 512, 600, 1024, 1200, 2048 pulses/revolution, single output
Dynapar X25 Explosionproof
Flange mounted tach, UL listed for Class 1, Division 1 & 2, Groups
C, D, E, F, G locations, 5-26 VDC input, push-pull and differential line
driver, 5-26 VDC output, single output 1/2-14 NPTF conduit entry.
Heavy industrial enclosure.

Environmental Rating

Motor Pricing

CD180AT-CD5010AY

$1325

OUTLINE PAGE ___
Explosionproof
Industrial Applications with
temperatures between
0°C and +70°C
$3360

$3864

Accessories &
Modifications

MOTOR MOUNTED, DIRECT CONNECTED TACHOMETERS

Notes:
The HA625, H56 and X25 require a Tach mounting kit. (Tach mounting kit consists of Tach adapter, coupling and stub shaft). The H56 can also be foot mounted.
The HA625, H56 and X25 can not be mounted on CD180-CD210 TEFC motors. Use TENV enclosure.
(ppr) pulses per revolution, required at time of order

CUSTOMER SUPPLIED TACHOMETERS
Customer-supplied tachometers will not be tested. Drawings and parts list of customer-supplied tachometers must
be received at the time of order. Both the tachometer and shipping papers must be tagged with the GE order and
item number. Refer to customer-supplied material section (page 3.12, Item 14) for additional information.
MOTOR FRAME SIZE
MOTOR MOUNTED, DIRECT CONNECTED TACHOMETERS

CD180AT-CD5010AY

CD6000

For mounting only of a customer-supplied Type C-Face tachometer. (This includes coupling,
stub shaft, mounting bracket, and assembly of tachometer.)

$3024

$3858

For mounting kit only for customer-mounted Type C-Face tachometer. (This includes coupling, stub
shaft, and mounting bracket.) Mounting kit is assembled to the motor.

$1666

$2500

Application
Information

List Price Addition

TERMINAL BOARD IN CONDUIT BOX
Generally, all power, field and other internal accessory terminals will be located on a terminal board in the conduit
box. On some higher current machines, the field and other internal accessory terminals will be located on a terminal
board, but the power leads will be fixed and supported separately (all within the conduit box).
On machines rated 2,000 amps or more, the field and other internal accessory terminals will be located on a
terminal board and the power leads will be fixed and supported separately as standard (all within the conduit box.)
Motor Frame Size

Shunt Wound

Stabilized Shunt or Compound Wound

CD218AT-CD5010AY
CD6000-CD6900

$1200
No Price Addition

$1500
Not Available

Terms

30

Note: Not available for explosionproof motors.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Outline
Dimensions

29
Cont’d

DESCRIPTION

Other

ITEM

General
Information

CD180AT through CD6900

3.29

Accessories and Modifications

ITEM
31

Motor Pricing

General
Information

CD180AT through CD6900

DESCRIPTION
TESTS AND CURVES
AVAILABLE FOR CD180-CD5010 FRAME AND CD6000 FRAME MOTORS
Routine Test

Accessories &
Modifications

Neutral Check
Winding Resistance
High Potential
Commutation Check
Voltage Regulation
Vibration Test
Saturation Curve
No Load Speed
Running Full Load

Motor

Generator

YES
YES
YES
YES
NO
YES
NO
YES
YES

YES
YES
YES
YES
YES
YES
YES
NO
YES

Complete Test

Motor

Generator

Neutral Check
Full Load Heat Run
Winding Resistance
High Potential
Commutation Adjustment
Saturation Curve
Voltage Regulation
Running Full Load

YES
YES
YES
YES
YES
NO
NO
YES

YES
YES
YES
YES
YES
YES
YES
YES

Speed Regulation (base speed
and top weak field speed)

YES

NO

Accessories &
Modifications

CHARGES
Tests

Net Price Addition

Outline
Dimensions

A. Certified Test Report - Electrically duplicate machine previously tested
B. Unwitnessed Routine Test - 5 copies of certified test reports
C. Witnessed Routine Tests - 5 copies of certified test reports
D. Unwitnessed Complete Test - 5 copies of certified test reports
E. Witnessed Complete Test - 5 copies of certified test reports

Curves

Net Price Addition
$300 net
$300 net

Terms

Other

Application
Information

A. Speed and Torque vs Load Current Curve
B. HP and Efficiency vs Load Current Curve

$300 net per motor
$300 net per motor
$1800 net per motor; Add 2 weeks lead time
$4250 net per motor; Add 2 weeks lead time
$5500 net per motor; Add 3 weeks lead time

3.30

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

32

TEMPERATURE DETECTORS
A bimetallic temperature-sensing device is mounted on the commutating coil. The device is available with normally
open or normally closed contactors. Specify whether normally open or normally closed contacts are required. (Included
as standard on TEUC motors). Thermostats are typically normally closed and the opening temperature is between
120°C to 150°C. Thermostats with special temperature rating are non-standard. Refer to GE when required.
Maximum Current Ratings (Normally open or normally closed contacts)
Load

125V AC

250V AC

600V AC

30V DC

Resistive

5 Amps

2.5 Amps

Inductive*

3 Amps

1.5 Amps

1 Amp
0.5 Amp
(Do not use above 600V AC)

5 Amps
1.5 Amps
(Do not use above 30V DC)

* Suitable for pilot duty only (relay coils)

For the following types of temperature detectors mounted in the locations indicated, see below for pricing.
Price does not include electronic sensor module.

Commutator Field or Shunt Field
List Price Addition

a. Thermostats
b. Thermistors (PTC Type)
c. Resistance Temperature Detectors (RTD)
Copper - 10 Ohm
Platinum - 100 Ohm
Nickel - 120 Ohm
d. Thermocouples (Type J)

$310
$450

$2266
$4532
$2266
$2266

$900
$1800
$900
Not Available

VERTICAL MOUNTING (FOOTED)
The following applies to vertically-operated foot- or flange-mounted, standard ball bearing, motors where no
external thrust is reflected back to the motor shaft. Refer to GE for external thrust limitations. For vertical brake
applications, refer to Modification Item 8a. Note: For crane motors, refer to page 3.11, Item 13.
All dripproof and splashproof motors which are mounted vertically require non-standard covers (the louvers are
rotated to provide protection in the vertical position). Totally enclosed motors require no modifications to the covers.
Frames CD180AT-CD320AT do not require internal modification for vertical mounting. Thus, a standard motor in
these frame sizes is suitable for vertical mounting.
Frames CD360AT-CD6900 require internal modification for vertical mounting. Thus, a standard motor in these frame
sizes is not suitable for vertical mounting. The CD365AT-CD5010AY frames require shaft seals for vertical mounting
with the shaft down. The CD365AT-CD5010AY frames mounted shaft up require additional modifications to the
bearings and shaft. Refer to GE for applications involving vertical mounting of CD6000-CD6900 frames.
Enclosure
Vertical Shaft Down
Vertical Shaft Up

CD180AT-CD320AT

CD365AT-CD5010AY

DP

Add 2%

Add 2% + $596

TE

No Price Addition*

Add 2% + $596*

DP

Add 2%
No Price Addition

Add 2% + $1050

TE

CD6000-CD6900

Refer to GE

Add 2% + $1050

Terms

33

Not Available
Not Available

Notes:
DP Dripproof
TE Totally Enclosed
* If TEFC waterproof, contact GE
For CD180AT, will not meet NEMA definition for DPFG, the motor is considered “fully guarded”. (Refer to page 3.16, Item 17 for C-Face and D-Flange pricing.)

www.gemotors.com

•

800-541-7191

Outline
Dimensions

Bearing

Application
Information

TEMPERATURE DETECTORS

Accessories &
Modifications

LOCATION

Other

Thermostat ratings for DPFG and
TE motors (standard on TEAAC, TEWAC
and explosionproof motors)

Motor Pricing

DESCRIPTION

Accessories &
Modifications

ITEM

General
Information

CD180AT through CD6900

GEP387M 09/11 • Prices and data subject to change without notice.

3.31

Accessories and Modifications

ITEM
34

DESCRIPTION
VOLTAGES

34a Armature, Non-Standard
Provides for special armature voltages, with same speed range and operating characteristics as standard ratings.
Frames may be different than standard.
VOLTAGES, ARMATURE (NON-STANDARD)

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

Voltage

HP

Base Speed RPM

120
105-130

1-3

1150-3500
Contact GE
ALL
ALL
ALL
300-1150
ALL
ALL
ALL

1-250
300-2000
7 1/2-4500
500-1000
1250-4500
300-1000
1250-4500

550
600
700

Outline
Dimensions

Accessories &
Modifications

750

Application
Information

No price addition
No price addition
Add 3%
No price addition
Add 6%
No price addition
Add 6%
Add 3%

Note: For voltages not
listed in the table, refer
to GE with application
requirements, including
type of power supply,
speed range by field
control, and armaturevoltage control.

34b Field, Standard
The following field voltages are standard. Voltages listed are nominal values. For more exact values, refer to GE.
Standard Armature Voltages

Standard Field Voltages
(Frames CD5010AY and Below)

Standard Field Voltages
(CD6000-CD6900 frames)

180
240, 500, 700

100, 200
120, 150, 240, 300

—
120, 150, 200, 240, 300

34c Field, Non-Standard
Non-standard field voltages can be obtained by using the standard fields and adding a series resistance. For
non-standard field voltages and pricing, refer to GE.
35

WARRANTY EXTENSION
The standard warranty for Kinamatic motors is 24 months from title transfer to third party, and 30 months from
shipment by seller, whichever occurs first. The CD6000 standard warranty is 12 months from title transfer to 3rd
party, and 18 months from shipment by seller, whichever occurs first. Extended warranties are available as follows:

35a Kinamatic Warranty Extension
From Title Transfer to 3rd Person

From Shipment by Seller

List Price Addition

36 months

42 months

Add 3% of Motor NET Price

35b CD6000 Series Warranty Extension
From Title Transfer to 3rd Person

From Shipment by Seller

List Price Addition

24 months

30 months

Add 3% of Motor NET Price

Terms

Other

List Price Addition

3.32

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

36

WINDINGS, STABILIZED SHUNT, COMPOUND OR SERIES
Stabilized shunt, compound, or series windings are not available on frames CD329AT, CD6700, CD6800 and
CD6900. These frames are only available with shunt wound fields. Also not available on some CD328AT frames.
Refer to GE for all design verification.
Standard motors are shunt wound. Where speed regulation greater than that provided by shunt wound is required,
a compound or stabilized shunt wound motor may be specified.
Standard compound wound motors will have approximately 15-25% speed regulation at rated speed. For other
degrees of compounding, refer to GE.

WARNING:
Series motor excitation is entirely dependent on load. The application of series motors should be avoided
where the load may drop below 25% rated torque or where the load is not solidly coupled, since the motor
may overspeed. Standard base speeds of series wound motors are different than shunt wound motors. Refer
to GE for exact speeds.
MOTOR LIST PRICE

DESCRIPTION

Up to
$2500

$3593
to
$5578

$5579
to
$9748

$9749 $13219 $23923 $42137 $61751 $98629 $157704 $252289
to
to
to
to
to
to
to
to
$13218 $23922 $42136 $61750 $98628 $157704 $252288 $403650

$403651
and up

Outline
Dimensions

Accessories &
Modifications

CAUTION:
Compound wound motors are generally not suited to applications requiring speed control by field weakening.
In no case should the field be weakened more than enough to obtain 125% of rated speed. When use with
field weakening is intended, the order must specify the speed range. The nameplate will show maximum
allowable speed.

$2501
to
$3592

Motor Pricing

DESCRIPTION

Accessories &
Modifications

ITEM

General
Information

CD180AT through CD6900

For Stabilized Shunt,
Compound or
Series Windings*

$244

$244

$330

$424

$516

$690

$892

$1540

$2430

$4860

$9720

$19440

Not
Available

Terms

Other

* For frames where this is not available, see above.

Application
Information

List Price Addition

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.33

Accessories and Modifications
General
Information

CD180AT through CD6900

ITEM
37

DESCRIPTION
MOD SHOP PRICING
FRAME SIZE

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Accessories &
Modifications

Motor Pricing

Modification

CD180AT

CD210ATCD280AT

CD320AT

CD360AT

CD400AT

CD500ATCD5010AY

Mod Shop Fee

$250

$320

$650

$720

$1200

$1600

Standard C-Face Endshield (Specify 4.5" or 8/5" for CD180AT)
Conduit Box:
Condulet Off Main Conduit Box (for accessory leads)
Waterproof
Covers:
Transparent* (Lucite® or equivalent)
Transparent* (Lexan® or equivalent)
Auxiliary or Customer Nameplate
Enclosure Conversions:
DPFG-BV (Blower, with filter, mounted on comm end only)
- 230/460 Volt, 60Hz
DPFG (Self-Ventilated - Motor must have internal fan, Contact GE)
DPFG-SV (Separately Ventilated on comm end only)
SPFG Splashproof Fully Guarded (add for Blower as required)
Sliding Base (Horizontal mounting only)
Transition Base (Horizontal mounting only)
Space Heater (120V AC Standard - Inquire for optional voltages)
Tachometers (Analog)
Type AN-AC 45 or 90V/1000 RPM
Form Y (PY), DC 50 or 100V/1000 RPM (max speed 2500 RPM)
Type BC
- BC42, 50 or 100V/1000 RPM
- BC46, 50, 100, or 200V/1000 RPM
Type BC Waterproof or Dustproof
- BC42, 100V/1000 RPM
- BC46, 100V/1000 RPM
Tachometers (Digital)
Avtron AV850 SMART-Tach II™ (Type AN-DG) (HD)
- 240, 600, 1024, or 1200 ppr, single output
- 240, 600, 1024, or 1200 ppr, dual output
Northstar RIM Tach™ RT8A
- 240, 512, 600, 1024, or 1200 ppr, single output
- 240, 512, 600, 1024, or 1200 ppr, dual output
Tachometer Mounting Only
Form Y (PY) Mounting Kit Only Assembled to Motor
- Includes Coupling, Stub Shaft, Mounting Bracket for PY
Type C-Face Tachometer Mounting Kit Only Assembled to Motor
- Includes Coupling, Stub Shaft, Mounting Bracket
Mounting Customer-supplied C-Face tachometer
- Includes Coupling, Stub Shaft, Mounting Bracket
Vertical (Frame will be supplied with feet)

$200

$725

$1200

$3000

N.A.

N.A.

$605
$495

$605
$495

$605
$495

$825
$990

$825
$990

$825
$990

$300
$600
$60

$300
$600
$60

$450
$900
$60

$450
$900
$60

$450
$900
$60

$450
$900
$60

$1600
$300
$300
$300
$300
$450
$640

$2850
$300
$300
$300
$450
$900
$640

$3150
$600
$600
$600
$600
$1200
$640

$3500
$600
$600
$600
$1100
$2200
$640

$4100
$600
$600
$600
$2000
$4000
$640

$5250
$1200
$1200
$1200
$2600
$5200
$640

$1975
$5400

$1975
$5400

$1975
$5400

$1975
$5400

$1975
$5400

$1975
$5400

$8175
$11000

$8175
$11000

$8175
$11000

$8175
$11000

$8175
$11000

$8175
$11000

$9025
$11800

$9025
$11800

$9025
$11800

$9025
$11800

$9025
$11800

$9025
$11800

$5300
$7750

$5300
$7750

$5300
$7750

$5300
$7750

$5300
$7750

$5300
$7750

$4650
$5750

$4650
$5750

$4650
$5750

$4650
$5750

$4650
$5750

$4650
$5750

$1850

$1850

$1850

$1850

$1850

$1850

$1850

$1850

$1850

$1850

$1850

$1850

$3325

$3325

$3325

$3325

$3325

$3325

* Not Available on all CD180AT frames or CD210AT TEFC Frames

3.34

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessories and Modifications

ITEM

General
Information

CD180AT through CD6900

DESCRIPTION

D450 5CD184TA094B070

Motor List
Mod Shop Fee

Lexan Covers

$18,098

Motor Pricing

37 Pricing Example
Cont’d

$650
$900
$640

Mod Motor List

$21,050

GO-2A Multiplier

x 0.5

Mod Motor Net

$10,525

Accessories &
Modifications

120V Space Heater

Accessories &
Modifications

Additional Information:
1. MOTOR – List price from GE Standard Products Catalog or Elitenet
2. MOD SHOP FEE – List price per the appropriate frame size from the top row of this price list
3. MODIFICATION LIST PRICE – Add price(s) for all modifications from the price list
4. GE MULTIPLIER SYMBOL – Use your appropriate multiplier based on multiplier symbol for stock motor
5. MULTIPLIER TIMES TOTAL LIST = NET PRICE

If you have any questions, or require a modification that is not listed, please contact your GE Sales
Representative or call 800-541-7191.

Terms

Other

Application
Information

Outline
Dimensions

Pricing subject to change without notice. Verify pricing and lead time with your GE Sales Representative at
time of order.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.35

Accessories and Modifications

Notes

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Accessories &
Modifications

Motor Pricing

General
Information

CD180AT through CD6900

3.36

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Outline Dimensions

6000 to 6900 . . . . . .
6000 to 6900 . . . . . .
6000 to 6200 . . . . . .
6700 to 6900 . . . . . .

www.gemotors.com

•

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
4.24
4.25
4.26
4.27
4.28
4.29
4.30
4.31
4.32
4.33
4.34
4.35

6000 to 6200 . . . .
6700 to 6900 . . . .
6050 to 6066 . . . .
6154 to 6177 . . . .
6259 to 6280 . . . .
6766 to 6785 . . . .
6873 to 6896 . . . .
6977 to 6999 . . . .
180AT to 5010AY . .
6000 to 6900 . . . .
180AT to 500AT . . .
and 6000 to 6900
180AT to 500AT . . .
and 6000 to 6900
180AT to 6900 . . . .
180AT to 6900 . . . .
180AT to 6900 . . . .
180AT to 6900 . . . .
CD180AT to CD6900
CD180 to CD6900. .
CD180 to CD6900. .
180AT to 6900 . . . .
180AT to 6900 . . . .

.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.

TEWAC . . . . . . . . .
TEWAC . . . . . . . . .
Air Openings . . . . . .
Air Openings . . . . . .
Air Openings . . . . . .
Air Openings . . . . . .
Air Openings . . . . . .
Air Openings . . . . . .
Accessory Mountings
Accessory Mountings
Accessory Couplings.

.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.

4.40
4.41
4.42
4.43
4.44
4.45
4.46
4.47
4.48
4.49
4.50

. . Accessory Adapters . . . 4.51
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.

Speed Limit Device . . . .
Avtron Tachometer. . . .
Avtron Tachometer. . . .
Type AN Tachometer . .
Northstar Tachometer. .
Northstar Tachometer. .
Dynapar Encoder. . . . .
Dynapar Rotopulse. . . .
eXcellon® Type BC . . . .
Tachometer
180AT to 6900 . . . . . . eXcellon® Form Y . . . . .
Tachometer
180AT to 500AT . . . . . Sliding Base . . . . . . . .
CD210AT to CD500AT . Soleplates . . . . . . . . .
CD6050 to CD6280 . . . Soleplates . . . . . . . . .
CD6766 to CD6999 . . . Soleplates . . . . . . . . .
NEMA Mounting Configurations . . . . . . . . . . .

4.52
4.53
4.54
4.55
4.56
4.57
4.58
4.59
4.60

Motor Pricing

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

Modifications
Pricing

DPFG, TENV . . . .
DPFG, TENV . . . .
DPFG, TENV . . . .
DPFG, TENV . . . .
TEFC . . . . . . . . .
TEFC . . . . . . . . .
TEFC . . . . . . . . .
TEFC . . . . . . . . .
DPFG, TENV . . . .
DPFG, TENV . . . .
DPFG, TENV . . . .
TEFC . . . . . . . . .
TEFC . . . . . . . . .
DPFG, TENV . . . .
DPFG, TENV . . . .
Conduit Box . . . .
TEFC . . . . . . . . .
Explosionproof . .
Explosionproof . .
TEAAC . . . . . . . .
TEAAC . . . . . . . .
TEAO . . . . . . . .
Air Openings . . . .
Blower Ventilated.
Blower Ventilated.
Blower Ventilated.
Blower Ventilated.
DPFG-SV, ESV . . .
DPFG-SV, ESV . . .
DPFG-SV, ESV . . .
DPFG-SV, ESV . . .
DPFG-SV, ESV . . .
DPFG-SV, ESV . . .
Blower Ventilated,
No Filter
Blower Ventilated,
With Filter
Splashproof, . . . .
Blower Ventilated
TEAAC . . . . . . . .
TEAAC . . . . . . . .

Page

Accessories &
Modifications

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

Outline

Outline
Dimensions

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

Frame Size

4.61
4.62
4.63
4.64
4.65
4.66

Application
Information

L182AT to 189AT. . .
L182ACY to 189ACY
L182ATC to 189ATC.
L182ATD to 189ATD
L182AT to 189AT. . .
L182ACY to 189ACY
L182ATC to 189ATC.
L182ATD to 189ATD
218AT to 329AT . . .
218ATC to 329ATC .
218ATD to 329ATD .
218AT to 2110AT . .
258AT to 328AT . . .
365AT to 5010AY . .
365ATD to L508ATD
365AT to 5010AY . .
365AT to L409AT . .
188AT to 409AT . . .
188ATC to 189ATC .
366AT to L508AT . .
5010AY . . . . . . . .
327AT to L508AT . .
210AT to 5010AY . .
180AT to 280AT . . .
320AT . . . . . . . . .
360AT to 400AT . . .
500AT . . . . . . . . .
6050 to 6066 . . . .
6154 to 6177 . . . .
6259 to 6280 . . . .
6766 to 6785 . . . .
6873 to 6896 . . . .
6977 to 6999 . . . .
6000 to 6900 . . . .

Page

Other

Outline

. . . . 4.36
. . . . 4.37
Terms

Frame Size

General
Information

Index

. . . . 4.38
. . . . 4.39

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.1

Frames L182AT to 189AT

Dripproof Fully Guarded and
Totally Enclosed Nonventilated

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

COMMUTATOR END

DRIVE END

FC

KEY .1875 X .1875
.88 LONG

Accessories &
Modifications

22.5°

R5.20

.14
2.25

3

KEY
.25 X .25 X 1.38 LG

2.00

3

.8750
.8745

1.1250
1.1245

R4.92

8.93

4.50
4.47

4

2

4
2.00

(4) HOLES
.4062 DIA.

2F

2.76

1.50

3.75

B
MAX

.38

7.50
8.90 MAX.

Commutator end shaft extension is furnished only when
➀	 Splashproof fully guarded machines will have additional covers,
increasing the overall width at the commutator end and drive end
pg102 specifically ordered.
side air openings.
Shaft runout shall not exceed 0.002 inch total indicator reading.
➁	 	Dripproof, fully guarded vertical drive end shaft down machines will
The standard single shaft machine has the commutator end bearing
have additional covers, increasing the overall width and exceeding
bracket and shaft extension prepared to accept accessories. For
bottom of mounting feet at the commutator end openings.
additional information, see page 4.48.
➂	 	Represents minimum length of shaft available for hubs.
➃	 	Air openings for dripproof fully guarded. Totally enclosed machines
will not have openings.

Application
Information

Outline
Dimensions

2.39

.75 NPT FOR
CONDUIT

1.50

Modifications
Pricing

Motor Pricing

.20

1.44

8.88
CONDUIT
HOLE

BS

1.75

1

1
1.44

C

Frame

Approx. Wk² of
Arm. Lb. Ft.²

B

C

For blower ventilated, blower can only be mounted on side of motor,
because there’s no air opening at the top of the motor. The motor leads
exit at the top of the motor.

FC

2F

BS

0.28

5.80

15.26

16.51

4.50

6.63

83

186AT

0.45

8.30

16.76

18.01

7.00

8.13

105

L186AT

0.67

8.30

18.76

20.01

7.00

10.13

128

189AT

0.77

11.56

20.76

22.01

10.00

12.13

162

Other

L182AT

Terms
4.2

Approx.
Net Wt. Lbs.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames L182ACY to 189ACY

Dripproof Fully Guarded and
Totally Enclosed Nonventilated

4.5” Type C-Face Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

COMMUTATOR END

1

9.24 DRIVE
END COVER

.12

.70

CONDUIT
HOLE

ACCESSORY
MOUNTING
FACE

1.44

R5.20

.375-16 THREAD
MINIMUM THREAD
ENGAGEMENT .50; MAX
BOLT PENETRATION .62(4) HOLES, EQUALLY
SPACED

.14 MAX.

1

2.00

BS

.75 NPT FOR
CONDUIT

3

KEY
.1875 X .1875 X 1.38 LG

6.50
8.94

2
R4.92

.12

4

4.50
4.47

5.88
8.82
MAX.

4.500
4.497

.8750
.8745

45°

4

1.50

(4) HOLES
.4062 DIA.

2.00

.38
3.75

2F

7.50

2.25

B
MAX

8.90 MAX.

.13
2.75

➀ Splashproof fully guarded machines will have additional covers,
increasing the overall width at the commutator end and drive end
PG103
side air openings.

Mounting face will be square and rabbet diameter concentric with shaft
within .004 inch total indicator reading.

➁	 	Dripproof, fully guarded vertical drive end shaft down machines will
have additional covers, increasing the overall width and exceeding
bottom of mounting feet at the commutator end openings.

The standard single shaft machine has the commutator end bearing
bracket and shaft extension prepared to accept accessores. For
additional information, see page 4.48.

Outline
Dimensions

Shaft runout not to exceed .002 inch total indicator reading.

➂	 	Represents minimum length of shaft available for hubs.
➃	 	Air openings for dripproof fully guarded. Totally enclosed machines
will not have openings.

Approx. Wk² of
Arm. Lb. Ft.²

B

C

2F

AG

BS

L182ACY

0.28

5.80

15.26

4.50

13.14

6.63

9.51

80

186ACY

0.45

8.30

16.76

7.00

14.64

8.13

11.01

102

L186ACY

0.67

8.30

18.76

7.00

16.64

10.13

13.01

128

189ACY

0.77

11.56

20.76

10.00

18.64

12.13

15.01

162

Approx.
Net Wt. Lbs.

Terms

Other

BV

Application
Information

Frame

Accessories &
Modifications

22.5°
1.44

2.12

BV

Modifications
Pricing

AG

8.88

Motor Pricing

C

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.3

Frames L182ATC to 189ATC

Dripproof Fully Guarded and
Totally Enclosed Nonventilated

8.5” Type C-Face Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
KEY
.1875 X .1875
X .88 LONG

Motor Pricing

COMMUTATOR END

FC

C

8.88

1

CONDUIT
HOLE

1.44

BV
ACCESSORY
MOUNTING
SURFACE

1
1.44

R5.20

9.24 DRIVE
END COVER

2.12

.70

22.5°

.20

.30
MIN.

.75 NPT
FOR CONDUIT

.500-13 THREAD
.75 DP (MAX BOLT
PENETRATION .82)
(4) HOLES
EQUALLY SPACED

3
2.00

BS

KEY
.25 X .25 X 1.38 LG

Modifications
Pricing

1.75
1.50

3

8.94
R4.92
.8750
.8745

(4) HOLES
.4062 DIA.

2.00

.38
3.75

Accessories &
Modifications

1.1250
1.1245

45°

4

1.50

.13

2F

7.50

2.75
2.25

B
MAX

8.90 MAX.

➀	 Splashproof fully guarded machines will have additional covers,PG104 Mounting face will be square and rabbet diameter concentric with
shaft within .004 inch total indicator reading.
increasing the overall width at the commutator end and drive end
side air openings.
Shaft runout not to exceed .002 inch total indicator reading.
➁	 	Dripproof, fully guarded vertical drive end shaft down machines will
have additional covers, increasing the overall width and exceeding
bottom of mounting feet at the commutator end openings.
➂	 Represents minimum length of shaft available for hubs.
➃	 	Air openings for dripproof fully guarded. Totally enclosed machines
will not have openings.

Commutator end shaft extension is furnished only when
specifically ordered.
The standard single shaft machine has the commutator end bearing
bracket and shaft extension prepared to accept accessores. For
additional information, see page 4.48.

Frame

Approx. Wk² of
Arm. Lb. Ft.²

B

C

FC

2F

BS

L182ATC

0.28

5.80

15.26

16.51

4.50

6.63

9.51

80

186ATC

0.45

8.30

16.76

18.01

7.00

8.13

11.01

102

L186ATC

0.67

8.30

18.76

20.01

7.00

10.13

13.01

128

189ATC

0.77

11.56

20.76

22.01

10.00

12.13

15.01

162

BV

Approx.
Net Wt. Lbs.

Terms

Other

Application
Information

Outline
Dimensions

8.82
MAX.

.12

4

4.50
4.47

7.25

8.500
8.497

2

From 36C69710CA

4.4

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames L182ATD to 189ATD

Dripproof Fully Guarded and
Totally Enclosed Nonventilated

Type D-Flange Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
COMMUTATOR END

11.00
MAX.

C

1.44

8.88

1.44

1

.70

1

22.5°

BV

CONDUIT
HOLE

.5312
(4) HOLES
EQ. SP.

.23

.75 NPT
FOR CONDUIT

R5.20

45°

2.25

ACCESSORY
MOUNTING FACE

KEY
.25 X .25 X 1.38 LG

.45

BS
2.00

10.00

3

Motor Pricing

AG

2

Modifications
Pricing

8.94
9.000
8.997

R4.92

.12

4.50
4.47

1.1250
1.1245

1.50

2.00

.38
.4062
(4) HOLES

7.50

2.75
2F

2.37

8.90 MAX.

Accessories &
Modifications

3.75

B MAX

Mounting face will be square and rabbet diameter concentric with
shaft within .004 inch total indicator reading.

➁	 	Dripproof, fully guarded vertical drive end shaft down machines will
have additional covers, increasing the overall width and exceeding
bottom of mounting feet at the commutator end openings.

The standard single shaft machine has the commutator end bearing
bracket and shaft extension prepared to accept accessores. For
additional information, see page 4.48.

Shaft runout not to exceed .002 inch total indicator reading.

Outline
Dimensions

PG105

➀	 Splashproof fully guarded machines will have additional covers,
increasing the overall width at the commutator end and drive end
side air openings.

Frame

Approx. Wk² of
Arm. Lb. Ft.²

B

C

2F

AG

BS

L182ATD

0.28

5.80

15.26

4.50

13.01

6.63

9.38

82

186ATD

0.45

8.30

16.76

7.00

14.51

8.13

10.88

104

L186ATD

0.67

8.30

18.76

7.00

16.51

10.13

12.88

130

189ATD

0.77

11.56

20.76

10.00

18.51

12.13

14.88

164

Approx.
Net Wt. Lbs.

Terms

Other

BV

Application
Information

➂	 Represents minimum length of shaft available for hubs.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.5

Totally Enclosed
Fan Cooled

Frames L182AT to 189AT
General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
DRIVE END

COMMUTATOR END

9.94 DIA.

FC

8.88
2.39

.75 NPT FOR
CONDUIT

1

2.25

1.50

R5.20

KEY
.25 X .25 X 1.38 LG

2.00

KEY .1875 X .1875
.88 LONG

1

.8750
.8745

22.5°

.14

1.1250
1.1245

8.94

AIR
OUT

4.50
4.47

AIR
IN
2.00
2F

(4) HOLES
.4062 DIA.

B
MAX

Approx. Wk² of
Arm. Lb. Ft.²

B

.38

7.50
8.90 MAX.

PG106
Shaft
runout shall not exceed .002 inch total indicator reading.

For mounting position, see enclosure and mounting assembly.

Frame

1.50

3.75

2.75

➀	 Represents minimum length of shaft available for hubs.

Outline
Dimensions

Accessories &
Modifications

CONDUIT
HOLE

BS
.20

Modifications
Pricing

Motor Pricing

C
1.75

Commutator end shaft extension is furnished only when
specifically ordered.

C

FC

2F

BS

Approx.
Net Wt. Lbs.

0.28

5.80

17.45

19.47

4.50

6.63

83

0.45

8.30

18.95

20.97

7.00

8.13

105

L186AT

0.67

8.30

20.95

22.97

7.00

10.13

128

189AT

0.77

11.56

22.95

24.97

10.00

12.13

165

Terms

Other

Application
Information

182AT
186AT

From 36C697101BA

4.6

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames L182ACY to 189ACY

Totally Enclosed
Fan Cooled

4.5” Type C-Face Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

COMMUTATOR END

2.12

8.88

BV
.12

22.5°

.375-16 THREAD
MINIMUM THREAD
ENGAGEMENT .50; MAX
BOLT PENETRATION .62(4) HOLES, EQUALLY
SPACED

.14 MAX.

CONDUIT
HOLE
R5.20

.75 NPT FOR
CONDUIT

2.00

BS

1

KEY
.1875 X .1875 X 1.38 LG

AIR IN
45°

6.50
4.500
4.497
.12

AIR
OUT

.8750
.8745

2.00

1.50
.38
3.75

(4) HOLES
.4062 DIA.
2F

7.50

.13
2.75

B
MAX

8.90 MAX.

5.88

2.25

Accessories &
Modifications

4.50
4.47

8.82
MAX.

Modifications
Pricing

8.94

PG107
➀	 Represents minimum length of shaft available for hubs.
For mounting position, see enclosure and mounting assembly.

Motor Pricing

C
AG

9.94

Mounting face will be square and rabbet diameter concentric with
shaft within .004 inch total indicator reading.

Frame

Approx. Wk² of
Arm. Lb. Ft.²

B

C

2F

AG

BS

L182ACY

0.28

5.80

17.45

4.50

15.33

6.63

9.51

83

L186ACY

0.45

8.30

18.95

7.00

16.83

8.13

11.01

105

L186ACY

0.67

8.30

20.95

7.00

18.83

10.13

13.01

133

189ACY

0.77

11.56

22.95

10.00

20.83

12.13

15.01

165

Approx.
Net Wt. Lbs.

Terms

Other

Application
Information

BV

Outline
Dimensions

Shaft runout shall not exceed .002 inch total indicator reading.

From 36B467421TA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.7

Totally Enclosed
Fan Cooled

Frames L182ATC to 189ATC
8.5” Type C-Face Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
FC
COMMUTATOR END

Motor Pricing

.30
MIN.

CONDUIT
HOLE

8.88

BS

AIR IN

R5.20

.500-13 THD. - .75 DEEP
(MAX. BOLT PENETRATION .82)
(4) HOLES EQ. SP.

2.00

.75 NPT
FOR CONDUIT

.20

1

KEY
.25 X .25 X 1.38 LG

1.75

1

1.50

1.50

2.00

(4) HOLES
.4062 DIA.

45°

.13

2F

7.50

2.75
2.25

B
MAX

➀ Represents minimum length of shaft available for hubs.

PG108

For mounting position, see enclosure and mounting assembly.
Mounting face will be square and rabbet diameter concentric with
shaft within .004 inch total indicator reading.

Shaft runout shall not exceed .002 inch total indicator reading.
Commutator end shaft extension is furnished only when
specifically ordered.

Frame

Approx. Wk² of
Arm. Lb. Ft.²

B

C

FC

2F

AG

BS

L182ATC

0.28

5.80

17.45

19.47

4.50

15.33

6.63

9.51

83

186ATC

0.45

8.30

18.95

20.97

7.00

16.83

8.13

11.01

105

L186ATC

0.67

8.30

20.95

22.97

7.00

18.83

10.13

13.01

133

189ATC

0.77

11.56

22.95

24.97

10.00

20.83

12.13

15.01

165

BV

Terms

Other

Application
Information

Outline
Dimensions

7.25

8.82
MAX.

1.1250
1.1245

KEY
.1875 X .1875 X .88 LG.

.38
3.75

8.500
8.497

.12

AIR
OUT

.8750
.8745

4.50
4.47

8.90 MAX.

Accessories &
Modifications

2.12

BV

22.5°

8.94

Modifications
Pricing

C
AG

9.94

4.8

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Approx.
Net Wt. Lbs.

Frames L182ATD to 189ATD

Totally Enclosed
Fan Cooled

Type D-Flange Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

COMMUTATOR END

C
AG

R5.20

AIR IN

Ø11.00
MAX.

2.12
KEY
.25 X .25 X 1.38 LG

.23
.45

2.00

BS

8.94

45°

Ø
4.50
4.47

AIR
OUT

.28

Ø
2.00

3.75

1.50
7.50
8.90
MAX.

9.000
8.997

1.1250
1.1245
Ø10.00

.12

2F

Modifications
Pricing

BV

.13

Ø.5312
(4) HOLES
EQUAL SPACED

2.25

(4) HOLES
.4062 DIA.

Accessories &
Modifications

22.5°

2.74
B MAX

Mounting face will be square and rabbet diameter concentric with
shaft within .004 inch total indicator reading.

➀ Represents minimum length of shaft available for hubs.
For mounting position, see enclosure and mounting assembly.

Outline
Dimensions

Ø9.94

Motor Pricing

.75 NPT
CONDUIT

Shaft runout shall not exceed .002 inch total indicator reading.

Approx. Wk² of
Arm. Lb. Ft.²

B

L182ATD

0.28

5.80

186ATD

0.45

8.30

Frames L182ATD
to 189ATD
18.95
7.00

L186ATD

0.67

189ATD

0.77

C

AG

BS

4.50

15.20

6.63

9.38

85

16.70

8.13

10.88

107

8.30

20.95
7.00
18.70
Type D-Flange Mounting
w/feet

10.13

12.88

133

11.56

22.95

12.13

14.88

167

PAGE 4.9
17.45

20.70

Terms

Other

10.00

BV

Approx.
Net Wt. Lbs.

2F

Application
Information

Frame

From 36B467521FA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.9

Frames 218AT to 329AT

Dripproof Fully Guarded*, Splashproof
and Totally Enclosed Nonventilated

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
ZA

Modifications
Pricing
Accessories &
Modifications
Outline
Dimensions
Application
Information
Other

ZA

AB
AC

N

ACCESSORY
MOUNTING FACE

N-W

FN

XN

FV

V

0.20"

U

U
XL

AIR
INLET

BS

Terms

P

C

.70

Motor Pricing

FC

COMMUTATOR END

O

AF

D

AIR
OUTLET

FN-FW
FW
AIR
INLET

2F

AIR
OUTLET

HOLE FOR
AA CONDUIT

W

K APPROX

2E

H - HOLE

BA

A

B

Frame
218AT
219AT
2110AT
258AT
259AT
287AT
288AT
327AT
328AT
329AT

Frame
210
250
280
320

Approx.
Net Wt.
In Lb.
234
252
280
361
403
493
548
691
769
888

AB
9.620
10.62
11.34

Approx.
WK2 of Arm
Lb. Ft.2
1.350
1.490
1.710
2.910
3.310
4.670
5.360
8.450
9.670
11.40

AC
7.56
8.56
9.28

Drive End
Key
Width
0.3125
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000
0.5000
0.5000

Thick
0.3125
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000
0.5000
0.5000

AA=1.25
AF
3.62
3.62
3.62
Not Available

XL
5.94
5.94
5.94

G

J

E

Commutator
End Key
Lgth.
±.03
1.75
1.75
1.75
2.25
2.25
2.50
2.50
3.00
3.00
3.00

Width
0.2500
0.2500
0.2500
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000

XN
4.38
4.38
4.38

AB
11.48
11.74
12.46
13.44

DIMENSIONS IN INCHES

pg110A Max.

Lgth.
±.03
1.00
1.00
1.00
1.50
1.50
2.00
2.00
2.25
2.25
2.25

Thick
0.2500
0.2500
0.2500
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000

10.40
10.40
10.40
12.40
12.40
13.88
13.88
15.88
15.88
15.88

B Max.
11.56
12.56
14.06
14.06
15.56
14.16
15.66
15.96
17.96
19.96

DIMENSIONS IN INCHES
AA=2.00
AC
AF
XL
8.920
4.62
7.38
9.180
4.62
7.38
9.900
4.62
7.38
10.88
4.62
7.38

‡
D
5.25
5.25
5.25
6.25
6.25
7.00
7.00
8.00
8.00
8.00

C
24.22
25.22
26.72
27.14
28.76
30.98
32.72
33.44
35.32
37.94

XN
5.38
5.38
5.38
5.38

E
4.25
4.25
4.25
5.00
5.00
5.50
5.50
6.25
6.25
6.25

2F
10.0
11.0
12.5
12.5
14.0
12.5
14.0
14.0
16.0
18.0

AB

AC

14.90
15.12

11.28
11.50

G
0.50
0.50
0.50
0.62
0.62
0.64
0.64
0.50
0.75
0.75

H
0.4062
0.4062
0.4062
0.5312
0.5312
0.5312
0.5312
0.6562
0.6562
0.6562

AA=3.00
AF
Not Available
Not Available
6.62
6.62

J
2.00
2.00
2.00
2.25
2.25
2.50
2.50
3.00
3.00
3.00

K
2.20
2.20
2.20
2.00
2.00
2.00
2.00
2.30
2.30
2.30

XL

XN

10.50
10.50

8.56
8.56

DIMENSIONS IN INCHES
Frame
218AT
219AT
2110AT
258AT
259AT
287AT
288AT
327AT
328AT
329AT

N
2.91
2.91
2.91
3.41
3.41
3.91
3.91
4.41
4.41
4.41

O
10.46
10.46
10.46
12.46
12.46
13.94
13.94
15.94
15.94
15.94

P
10.42
10.42
10.42
12.42
12.42
13.88
13.88
15.88
15.88
15.88

U
1.375
1.375
1.375
1.625
1.625
1.875
1.875
2.125
2.125
2.125

∆
V
2.5
2.5
2.5
3.0
3.0
3.5
3.5
4.0
4.0
4.0

W
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16
0.16

N-W
2.75
2.75
2.75
3.25
3.25
3.75
3.75
4.25
4.25
4.25

* Dripproof, fully guarded machines can be used for wall or ceiling mounting.
Assembly modifications must be made to maintain proper enclosure.
‡ Dimensions “D” will not be exceeded. When exact dimension is required, shims up
to .03 inches may be necessary where dimension “D” is 8 inches or less. When
dimension “D” is over 8 inches, shims up to .06 inch may be necessary.
Splashproof machines will have additional covers, increasing the overall width at the
commutator end and drive end side cover openings.
∆ “V” represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.

BA
3.50
3.50
3.50
4.25
4.25
4.75
4.75
5.25
5.25
5.25

FC
25.97
26.97
28.47
29.39
31.01
33.75
35.47
36.69
38.57
41.19

FN
2.45
2.45
2.45
2.95
2.95
3.45
3.45
3.95
3.95
3.95

FU
1.125
1.125
1.125
1.375
1.375
1.625
1.625
1.875
1.875
1.875

∆
FV
2.0
2.0
2.0
2.5
2.5
3.0
3.0
3.5
3.5
3.5

FW
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2

FN-FW
2.25
2.25
2.25
2.75
2.75
3.25
3.25
3.75
3.75
3.75

BS
8.360
9.360
10.87
9.650
11.26
10.89
12.62
11.80
13.68
16.30

XZ
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5

 For shipping weight add 15% to net weight.
10 	Refer to GE Energy for dimensions.
Conduit box will be assembled on the right hand side facing the commutator end
for motors, and on the left hand side facing the commutator end for generators.
Conduit box will be assembled on opposite side of frame, if so specified. Conduit box
may be oriented to accommodate customers’ application. Dimensions pertaining to
conduit boxes vary according to rating.
The standard single shaft machine has the commutator end bearing bracket and
shaft prepared to accept additional information, see page 4.48.
Commutator end shaft extension is furnished only when specifically ordered, and is
prepared for accessory drive.

From 36C697102AA

4.10

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames 218ATC to 329ATC

Dripproof Fully Guarded*, Splashproof
and Totally Enclosed Nonventilated

Type C-Face Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
FC

BF TAP (4) HOLES
EQUALLY SPACED

C

ZA

P
AC

BB
MIN.

FV
XN

V

.20

AK

FU

AF

AIR
OUTLET

BC
HOLE FOR
AA CONDUIT

BA

2F

Thick
0.3125
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000
0.5000
0.5000

Commutator
End Key
Lgth.
±.03
1.75
1.75
1.75
2.25
2.25
2.50
2.50
3.00
3.00
3.00

Width
0.2500
0.2500
0.2500
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000

Thick
0.2500
0.2500
0.2500
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000
BF

Frame
218ATC
219ATC
2110ATC
258ATC
259ATC
287ATC
288ATC
327ATC
328ATC
329ATC

Frame
210
250
280
320

BA
3.5
3.5
3.5
4.25
4.25
4.75
4.75
5.25
5.25
5.25

AB
9.620
10.62
11.34

BB Min.
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3

FN
2.45
2.45
2.45
2.95
2.95
3.45
3.45
3.95
3.95
3.95

AC
7.56
8.56
9.28

FU
1.125
1.125
1.125
1.375
1.375
1.625
1.625
1.875
1.875
1.875

AA=1.25
AF
3.62
3.62
3.62
Not Available

BC
0.25
0.25
0.25
0.24
0.24
0.24
0.24
0.24
0.24
0.24

XL
5.94
5.94
5.94

Tap
.500-13
.500-13
.500-13
.500-13
.500-13
.500-13
.500-13
.625-11
.625-11
.625-11

XN
4.38
4.38
4.38

DIMENSIONS IN INCHES
Lgth.
±.03 A Max.
1.00 10.40
1.00 10.40
1.00 10.40
1.50 12.40
1.50 12.40
2.00 13.88
2.00 13.88
2.25 15.88
2.25 15.88
2.25 15.88

B Max.
11.56
12.56
14.06
14.06
15.56
14.16
15.66
15.96
17.96
19.96

•

800-541-7191

5.25
5.25
5.25
6.25
6.25
7.00
7.00
8.00
8.00
8.00

DIMENSIONS IN INCHES
∆
Depth
FV
FW
FN-FW
1.00
2.0
0.2
2.25
1.00
2.0
0.2
2.25
1.00
2.0
0.2
2.75
1.00
2.5
0.2
2.75
1.00
2.5
0.2
2.75
1.00
3.0
0.2
3.25
1.00
3.0
0.2
3.25
1.25
3.5
0.2
3.75
1.25
3.5
0.2
3.75
1.25
3.5
0.2
3.75

AB
11.48
11.74
12.46
13.44

E
4.25
4.25
4.25
5.00
5.00
5.50
5.50
6.25
6.25
6.25

2F
10.0
11.0
12.5
12.5
14.0
12.5
14.0
14.0
16.0
18.0

AH
2.5
2.5
2.5
3.0
3.0
3.5
3.5
4.0
4.0
4.0

DIMENSIONS IN INCHES
AA=2.0
AC
AF
XL
8.920
4.62
7.38
9.180
4.62
7.38
9.900
4.62
7.38
10.88
4.62
7.38

* Dripproof, fully guarded machines can be used for wall or ceiling mounting
Assembly modifications must be made to maintain proper enclosure.
‡ Dimensions "D" will not be exceeded. When exact dimension is required, shims up
to .03 inches may be necessary where dimension "D" is 8 inches or less. When
dimension "D" is over 8 inches, shims up to .06 inch may be necessary.
Splashproof machines will have additional covers, increasing the overall width at the
commutator end and drive end side cover openings.
∆ “V” represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.

www.gemotors.com

‡

PG111
D

C
24.22
25.22
26.72
27.14
28.76
30.98
32.72
33.44
35.32
37.94

G
0.50
0.50
0.50
0.62
0.62
0.64
0.64
0.75
0.75
0.75

H
0.4062
0.4062
0.4062
0.5312
0.5312
0.5312
0.5312
0.6562
0.6562
0.6562

AJ
7.250
7.250
7.250
7.250
7.250
9.000
9.000
11.00
11.00
11.00

XN
5.38
5.38
5.38
5.38

J
2.0
2.0
2.0
2.3
2.3
2.5
2.5
3.0
3.0
3.0

AK
8.50
8.50
8.50
8.50
8.50
10.5
10.5
12.5
12.5
12.5

K
2.2
2.2
2.2
2.0
2.0
2.0
2.0
2.3
2.3
2.3

N
2.97
2.97
2.70
3.47
3.47
3.97
3.97
4.47
4.47
4.47

ZA
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5

O
10.46
10.46
10.46
12.46
12.46
13.94
13.94
15.94
15.94
15.94

P
10.42
10.42
10.42
12.42
12.42
13.88
13.88
15.88
15.88
15.88

Max
9.000
9.000
9.000
10.00
10.00
11.25
11.25
14.00
14.00
14.00

AB

AC

14.90
15.12

11.28
11.50

∆
V
2.5
2.5
1.5
3.0
3.0
3.5
3.5
4.0
4.0
4.0

U
1.375
1.375
1.375
1.625
1.625
1.875
1.875
2.125
2.125
2.125

BV
12.11
13.11
14.62
14.14
15.75
15.88
17.61
17.29
19.17
21.79

AA=3.0
AF
Not Available
Not Available
6.62
6.62

BS
8.360
9.360
10.87
9.650
11.26
10.87
12.62
11.80
13.68
13.68

W
0.22
0.22
0.22
0.22
0.22
0.22
0.22
0.22
0.22
0.22

N-W
2.75
2.75
2.75
3.25
3.25
3.75
3.75
4.25
4.25
4.25

FC
25.97
26.97
28.47
29.39
31.01
33.73
35.47
36.69
38.57
41.19

XL

XN

10.5
10.5

8.56
8.56

 For shipping weight add 15% to net weight.
10 	Refer to GE Energy for dimensions.
Conduit box will be assembled on the right hand side facing the commutator end
for motors, and on the left hand side facing the commutator end for generators.
Conduit box will be assembled on opposite side of frame, if so specified. Conduit box
may be oriented to accommodate customers’ application. Dimensions pertaining to
conduit boxes vary according to rating.
For frames CD218ATC thru CD288ATC inclusive, mounting face will be square and
rabbet diameter concentric with shaft within 0.004 inch total indicator reading.
"AK" dimension: +0.000 inch -0.005 inch.
For frames CD327ATC thru CD328ATC inclusive, mounting face will be square and
rabbet diameter concentric with shaft within 0.004 inch total indicator reading.
"AK" dimensions: +0.000 inch -0.005 inch.
Commutator end shaft extension is furnished only when specifically ordered, and
is prepared for accessory drive.
From 36C697102CA

GEP387M 09/11 • Prices and data subject to change without notice.

4.11

Accessories &
Modifications

Width
0.3125
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000
0.5000
0.5000

A

Outline
Dimensions

Frame
218ATC
219ATC
2110ATC
258ATC
259ATC
287ATC
288ATC
327ATC
328ATC
329ATC

Drive End
Key

G

J
2E

N

B

Approx. Approx.
Net Wt. WK2 of Arm
Lb. Ft.2
In Lb.
243
1.35
261
1.49
289
1.71
378
2.91
420
3.31
522
4.67
577
5.36
720
8.45
798
9.67
917
11.4

E

H - HOLE

N-W

Application
Information

FN-FW

D

Modifications
Pricing

AIR
OUTLET

K APPROX

AIR
INLET

O

XL

W
BS

FW

AJ

BD
MAX.

U

Motor Pricing

AB

Other

FN

ZA

AH

BV

.70
ACCESSORY
MOUNTING FACE

Terms

COMMUTATOR END

Frames 218ATD to 329ATD

Dripproof Fully Guarded*, Splashproof
and Totally Enclosed Nonventilated

Type D-Flange Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
COMMUTATOR END

FC
C

AB

AG

Motor Pricing

.70

ZA

P
45°

BF HOLE
(4) HOLES
EQUALLY
SPACED

FV
N

.20

Modifications
Pricing
Accessories &
Modifications
Outline
Dimensions
Application
Information
Other

ZA
BB
MAX.

XN

V
U

AIR
OUTLET

FU

Terms

BD

BE

ACCESSORY
MOUNTING
FACE

FN

AC

AH

BV

AK

BA

2F

G

J

AIR
INLET

(APPROX) K
H DIA.
(4) HOLES

D

HOLE FOR
AA CONDUIT

FW
AIR
INLET

O

AF

W

BS

FN-FW

AJ
XL

E
2E

B

A

Frame
218ATD
219ATD
2110ATD
258ATD
259ATD
287ATD
288ATD
327ATD
328ATD
329ATD

Approx. Approx.
Net Wt. WK2 of Arm
Lb. Ft.2
In Lb.
264
1.35
282
1.49
310
1.71
416
2.91
458
3.31
551
4.67
606
5.36
745
8.45
823
9.67
942
11.4

Drive End
Key
Width
0.3125
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000
0.5000
0.5000

Thick
0.3125
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000
0.5000
0.5000

Commutator
End Key
Lgth.
±.03
1.75
1.75
1.75
2.25
2.25
2.50
2.50
3.00
3.00
3.00

Width
0.250
0.250
0.250
0.313
0.313
0.375
0.375
0.500
0.500
0.500

Thick
0.2500
0.2500
0.2500
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000
0.5000

DIMENSIONS IN INCHES

pg112
Lgth.
±.03 A Max.
1.00 10.40
1.00 10.40
1.00 10.40
1.50 12.40
1.50 12.40
2.00 13.88
2.00 13.88
2.25 15.88
2.25 15.88
2.25 15.88

B Max.
11.56
12.56
14.06
14.06
15.56
14.16
15.66
15.96
17.96
19.96

C
24.22
25.22
26.72
27.14
28.76
30.98
32.72
33.44
35.32
37.94

‡
D
5.25
5.25
5.25
6.25
6.25
7.00
7.00
8.00
8.00
8.00

E
4.25
4.25
4.25
5.00
5.00
5.50
5.50
6.25
6.25
6.25

2F
10.0
11.0
12.5
12.5
14.0
12.5
14.0
14.0
16.0
18.0

G
0.50
0.50
0.50
0.62
0.62
0.64
0.64
0.75
0.75
0.75

H
0.4062
0.4062
0.4062
0.5312
0.5312
0.5312
0.5312
0.6562
0.6562
0.6562

J
2.00
2.00
2.00
2.25
2.25
2.50
2.50
3.00
3.00
3.00

K
2.2
2.2
2.2
2.0
2.0
2.0
2.0
2.3
2.3
2.3

N
2.97
2.97
2.97
3.47
3.47
3.97
3.97
4.47
4.47
4.47

O
10.46
10.46
10.46
12.46
12.46
13.94
13.94
15.94
15.94
15.94

P
10.42
10.42
10.42
12.42
12.42
13.88
13.88
15.88
15.88
15.88

U
1.375
1.375
1.375
1.625
1.625
1.875
1.875
2.125
2.125
2.125

V
2.5
2.5
2.5
3.0
3.0
3.5
3.5
4.0
4.0
4.0

W
0.22
0.22
0.22
0.22
0.22
0.22
0.22
0.22
0.22
0.22

BA
3.50
3.50
3.50
4.25
4.25
4.75
4.75
5.75
5.75
5.75

DIMENSIONS IN INCHES
Frame
218ATD
219ATD
2110ATD
258ATD
259ATD
287ATD
288ATD
327ATD
328ATD
329ATD

Frame
210
250
280
320

BB Max
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25

AB
9.620
10.62
11.34

BD
14
14
14
18
18
18
18
18
18
18

BE
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75

AC
7.56
8.56
9.28

BF
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125

AA=1.25
AF
3.62
3.62
3.62
Not Available

BV
11.86
12.86
14.86
13.89
15.50
15.63
17.37
17.04
18.92
21.54

XL
5.94
5.94
5.94

FC
25.97
26.97
28.47
29.39
31.01
33.73
35.47
36.69
38.57
41.19

XN
4.38
4.38
4.38

FN
2.45
2.45
2.45
2.95
2.95
3.45
3.45
3.95
3.95
3.95

AB
11.48
11.74
12.46
13.44

∆
FU
1.125
1.125
1.125
1.375
1.375
1.625
1.625
1.875
1.875
1.875

www.gemotors.com

•

800-541-7191

FW
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2

DIMENSIONS IN INCHES
AA=2.0
AC
AF
XL
8.920
4.62
7.38
9.180
4.62
7.38
9.900
4.62
7.38
10.88
4.62
7.38

* Dripproof, fully guarded machines can be used for wall or ceiling mounting
Assembly modifications must be made to maintain proper enclosure.
‡ Dimensions "D" will not be exceeded. When exact dimension is required, shims up
to .03 inches may be necessary where dimension "D" is 8 inches or less. When
dimension "D" is over 8 inches, shims up to .06 inch may be necessary.
Splashproof machines will have additional covers, increasing the overall width at the
commutator end and drive end side cover openings.
∆ “V” represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.

4.12

FV
2.0
2.0
2.0
2.5
2.5
3.0
3.0
3.5
3.5
3.5

FN-FW
2.25
2.25
2.25
2.75
2.75
3.25
3.25
3.75
3.75
3.75

XN
5.38
5.38
5.38
5.38

AG
21.47
22.47
23.97
23.89
25.51
27.23
28.97
29.19
31.07
33.69

AH
2.75
2.75
2.75
3.25
3.25
3.75
3.75
4.25
4.25
4.25

AJ
12.5
12.5
12.5
16.0
16.0
16.0
16.0
16.0
16.0
16.0

AB

AC

14.90
15.12

11.28
11.50

AK
11
11
11
14
14
14
14
14
14
14

AA=3.0
AF
Not Available
Not Available
6.62
6.62

BS
8.360
9.360
10.86
9.640
11.26
10.83
12.62
11.80
13.68
16.30

ZA
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5

XL

XN

10.5
10.5

8.56
8.56

 For shipping weight add 15% to net weight.
10 	Refer to GE Energy for dimensions.
Conduit box will be assembled on the right hand side facing the commutator end
for motors, and on the left hand side facing the commutator end for generators.
Conduit box will be assembled on opposite side of frame, if so specified. Conduit box
may be oriented to accommodate customers’ application. Dimensions pertaining to
conduit boxes vary according to rating.
For frames CD218ATC thru CD288ATC inclusive, mounting face will be square and
rabbet diameter concentric with shaft within 0.004 inch total indicator reading.
"AK" dimension: +0.000 inch -0.005 inch.
For frames CD327ATC thru CD328ATC inclusive, mounting face will be square and
rabbet diameter concentric with shaft within 0.004 inch total indicator reading.
"AK" dimensions: +0.000 inch -0.005 inch.
Commutator end shaft extension is furnished only when specifically ordered, and
is prepared for accessory drive.
From 36C697102DA

GEP387M 09/11 • Prices and data subject to change without notice.

Frames 218AT to 2110AT

Totally Enclosed
Fan Cooled

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
11.70 DIA.
10.41

FC
C

2.45
.20

-

2.25

KEY .25 X .25 X
1.00 LONG

2.00

KEY .3125 X .3125 X
1.75 LONG

AC

2.91

AIR
OUT

.15
2.75

XN

1

AB

Motor Pricing

COMMUTATOR END

2.50

1

BS
1.1250
1.1245

5.25
5.22

1.3750
1.3745

Modifications
Pricing

11.25

AF

AIR
IN
2.20 APPROX.

3

HOLE FOR
AA CONDUIT

3.50

2F

4.25
.50

2.00

.4062 DIA.
(4) HOLES

B
MAX.

8.50
10.40
MAX.

Accessories &
Modifications

5

pg113
B
11.56
12.56
14.06

C
26.82
27.82
29.32

FC
29.34
30.34
31.84

2F
10.0
11.0
12.5

BS
8.360
9.360
10.87

Approx.
Net Wt.
241
259
287

AB
9.620
11.48

AC
7.56
8.92

AF
3.62
4.62

XL
5.94
7.38

XN
4.38
5.38

➃ Shaft runout shall not exceed 0.002 inch total indicator reading on drive end.
➄ Shroud is removable to permit access to hand hole covers.
➅ Commutator end shaft extension is furnished only when specifically ordered.
 For shipping weight, add 15% to net weight.

Terms

Other

Application
Information

➀ Represents minimum length of shaft available for hubs.
➁ Machine can be used for wall or ceiling mounting.
➂ Conduit box will be assembled on the right hand side facing the commutator end
for motors, and on the left hand side facing the commutator end for generators.
Conduit box will be assembled on opposite side of frame, if so specified. Conduit box
may be oriented to accommodate customers’ application. Dimensions pertaining to
conduit boxes vary according to rating.

Conduit Box Dimensions
AA
1.25
2

Outline
Dimensions

Frame
218AT
219AT
2110AY

From 36C697102EA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.13

Frames 258AT to 328AT

Totally Enclosed
Fan Cooled

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
COMMUTATOR END

DRIVE END

FC
C

Motor Pricing

P

FN

XP

.06

AB

.93

AC

ACCESSORY
MOUNTING
FACE
AIR
OUTLET

N
N-W

XN

V

FV

O

XL

FU

Modifications
Pricing

AF

.20

D
HOLE FOR
AA CONDUIT
G

U

AIR
INLET

BS

E

E

W

FW

J

K (APPROX)

FN-FW

H HOLE

BA

2F
B MAX.

A MAX.

Frame
258AT
259AT
287AT
288AT
327AT
328AT

Approx.
Net Wt.
In Lb.
397
442
532
587
732
812

Approx.
WK2 of Arm
Lb. Ft.2
3.170
3.570
5.090
5.780
9.200
10.42

Width
0.375
0.375
0.500
0.500
0.500
0.500

Thick
0.375
0.375
0.500
0.500
0.500
0.500

Commutator
End Key
Lgth.
±.03
2.25
2.25
2.50
2.50
3.00
3.00

Width
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000

DIMENSIONS IN INCHES
Lgth.
±.03
1.50
1.50
2.00
2.00
2.25
2.25

Thick
0.3125
0.3125
0.3750
0.3750
0.5000
0.5000

A Max.
12.40
12.40
13.88
13.88
15.88
15.88

B Max.
14.06
15.56
14.16
15.66
15.96
17.96

‡
D
6.25
6.25
7.00
7.00
8.00
8.00

C
30.32
31.94
34.66
36.40
37.62
39.50

E
5.00
5.00
5.50
5.50
6.25
6.25

2F
12.5
14.0
12.5
14.0
14.0
16.0

G
0.62
0.62
0.64
0.64
0.75
0.75

H
0.5312
0.5312
0.5312
0.5312
0.6562
0.6562

J
2.25
2.25
2.50
2.50
3.00
3.00

K
2.0
2.0
2.0
2.0
2.3
2.3

DIMENSIONS IN INCHES
Frame
258AT
259AT
287AT
288AT
327AT
328AT

Frame
210
250
280
320

N
3.41
3.41
3.91
3.91
4.41
4.41

AB
9.620
10.62
11.34

O
12.75
12.75
14.25
14.25
16.25
16.25

AC
7.56
8.56
9.28

P
13.00
13.00
14.52
14.52
16.52
16.52

∆
V
3.0
3.0
3.5
3.5
4.0
4.0

U
1.625
1.625
1.875
1.875
2.125
2.125

AA=1.25
AF
3.62
3.62
3.62
Not Available

XL
5.94
5.94
5.94

XN
4.38
4.38
4.38

W
0.16
0.16
0.16
0.16
0.16
0.16

AB
11.48
11.74
12.46
13.44

N-W
3.25
3.25
3.75
3.75
4.25
4.25

BA
4.25
4.25
4.75
4.75
5.25
5.25

FC
32.64
34.26
37.48
39.22
40.94
42.82

DIMENSIONS IN INCHES
AA=2.0
AC
AF
XL
8.920
4.62
7.38
9.180
4.62
7.38
9.900
4.62
7.38
10.88
4.62
7.38

‡ Dimensions "D" will not be exceeded. When exact dimension is required, shims up
to .03 inches may be necessary where dimension "D" is 8 inches or less. When
dimension "D" is over 8 inches, shims up to .06 inch may be necessary.
∆ “V” represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.

FN
3.25
3.25
3.75
3.75
4.25
4.25

∆
FV
2.5
2.5
3.0
3.0
3.5
3.5

FU
1.375
1.375
1.625
1.625
1.875
1.875

XN
5.38
5.38
5.38
5.38

FW
0.5
0.5
0.5
0.5
0.5
0.5

AB

AC

14.90
15.12

11.28
11.50

FN-FW
2.75
2.75
3.25
3.25
3.75
3.75

AA=3.0
AF
Not Available
Not Available
6.62
6.62

BS
9.650
11.26
10.89
12.62
11.80
13.68

XP
12.42
12.42
13.88
13.88
15.88
15.88

XL

XN

10.5
10.5

8.56
8.56

 For shipping weight add 15% to net weight.
10 	Refer to GE Energy for dimensions.
Commutator end shaft extension is furnished only when specifically ordered, and is
prepared for accessory drive.
When commutator end shaft is not furnished, shaft and fan shroud on commutator
end is prepared for shaft driven accessories. Refer to 36C697103BA for dimensions.

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

pg114
Drive End
Key

From 36C697102BA

4.14

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames 365AT TO 5010AY

Dripproof Fully Guarded*, Splashproof
and Totally Enclosed Nonventilated

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
COMMUTATOR END

XZ

FC
ACCESSORY
MOUNTING
FACE

AB
AC

Motor Pricing

N

XN

N-W
V

V
XL

AE

K (APPROX)

FN

2F

AIR
INLET

Frame
365AT
366AT
368AT
407AT
L407AT
409AT
L409AT
504AT
L504AT
506AT
L506AT
508AT
L508AT
5010AY

Approx.
Net Wt.
In Lb.
750.0
860.0
1020
1300
1350
1600
1650
1900
2070
2290
2440
2810
2970
4260

Approx.
WK2 of Arm
Lb. Ft.2
15.610
18.270
22.210
35.470
35.540
43.810
43.880
79.100
79.150
98.760
98.810
121.87
122.92
157.28

HOLE(S) FOR
AA CONDUIT

AIR
OUTLET

BA

B MAX.

G

J

H HOLE

Modifications
Pricing

BS

FW

D

AIR
OUTLET
W

AD

AIR
INLET

E
2E
A

PG115

Drive End
Key
Width
0.625
0.625
0.625
0.625
0.625
0.625
0.625
0.750
0.750
0.750
0.750
0.750
0.750
1.000

Thick
0.625
0.625
0.625
0.625
0.625
0.625
0.625
0.750
0.750
0.750
0.750
0.750
0.750
1.000

Commutator
End Key
Lgth.
±.03
3.50
3.50
3.50
4.00
4.00
4.00
4.00
5.25
5.25
5.25
5.25
5.25
5.25
6.50

Width
0.500
0.500
0.500
0.625
0.625
0.625
0.625
0.750
0.750
0.750
0.750
0.750
0.750
0.750

Lgth.
±.03
3.00
3.00
3.00
3.50
3.50
3.50
3.50
4.50
4.50
4.50
4.50
4.50
4.50
5.25

Thick
0.500
0.500
0.500
0.625
0.625
0.625
0.625
0.750
0.750
0.750
0.750
0.750
0.750
0.750

DIMENSIONS IN INCHES

A Max. B Max.
17.920 14.16
17.920 15.90
17.920 19.90
20.000 20.16
20.000 20.16
20.000 24.16
20.000 24.16
24.920 18.96
24.920 18.96
24.920 22.96
24.920 22.96
24.920 27.96
24.920 27.96
24.920 34.86

C
33.70
35.90
38.90
40.12
43.52
44.62
48.02
45.74
47.50
49.74
51.50
54.74
56.50
65.49

‡
D
9.00
9.00
9.00
10.0
10.0
10.0
10.0
12.5
12.5
12.5
12.5
12.5
12.5
12.5

E
7.0
7.0
7.0
8.0
8.0
8.0
8.0
10
10
10
10
10
10
10

2F
12.25
14.00
18.00
18.00
18.00
22.00
22.00
16.00
16.00
20.00
20.00
25.00
25.00
32.00

G
0.74
0.74
0.74
0.86
0.86
0.86
0.86
1.11
1.11
1.11
1.11
1.11
1.11
1.11

H
0.8125
0.8125
0.8125
0.9375
0.9375
0.9375
0.9375
1.1875
1.1875
1.1875
1.1875
1.1875
1.1875
1.1875

J
3.26
3.26
3.26
4.00
4.00
4.00
4.00
4.50
4.50
4.50
4.50
4.50
4.50
4.50

K
2.31
2.31
2.31
2.38
2.38
2.38
2.38
3.00
3.00
3.00
3.00
3.00
3.00
3.00

N
4.92
4.92
4.92
5.42
5.42
5.42
5.42
6.67
6.67
6.67
6.67
6.67
6.67
8.42

DIMENSIONS IN INCHES
Frame
365AT
366AT
368AT
407AT
L407AT
409AT
L409AT
504AT
L504AT
506AT
L506AT
508AT
L508AT
5010AY

O
17.91
17.91
17.91
20.15
20.15
20.15
20.15
25.15
25.15
25.15
25.15
25.15
25.15
25.17

P
17.90
17.90
17.90
20.38
20.38
20.38
20.38
25.38
25.38
25.38
25.38
25.38
25.38
25.38

U
2.375
2.375
2.375
2.625
2.625
2.625
2.625
3.250
3.250
3.250
3.250
3.250
3.250
4.125

∆
V
4.50
4.50
4.50
5.00
5.00
5.00
5.00
6.25
6.25
6.25
6.25
6.25
6.25
8.00

W
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17

N-W
4.75
4.75
4.75
5.25
5.25
5.25
5.25
6.50
6.50
6.50
6.50
6.50
6.50
8.25

BA
5.875
5.875
5.875
6.625
6.625
6.625
6.625
8.500
8.500
8.500
8.500
8.500
8.500
8.500

FC
37.45
39.65
42.65
44.37
47.77
48.87
52.27
50.99
52.75
54.99
56.75
59.99
61.75
71.49

FN
4.45
4.45
4.45
4.95
4.95
4.95
4.95
5.95
5.95
5.95
5.95
5.95
5.95
6.70

* Dripproof, fully guarded machines can be used for wall or ceiling mounting
Assembly modifications must be made to maintain proper enclosure.
‡ Dimensions "D" will not be exceeded. When exact dimension is required, shims up
to .03 inches may be necessary where dimension "D" is 8 inches or less. When
dimension "D" is over 8 inches, shims up to .06 inch may be necessary.
Splashproof machines will have additional covers, increasing the overall width at the
commutator end and drive end side cover openings.
∆ “V” represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.

FU
2.125
2.125
2.125
2.375
2.375
2.375
2.375
2.875
2.875
2.875
2.875
2.875
2.875
3.25

∆
FV
4.00
4.00
4.00
4.50
4.50
4.50
4.50
5.50
5.50
5.50
5.50
5.50
5.50
6.25

FW
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2

FN-FW
4.25
4.25
4.25
4.75
4.75
4.75
4.75
5.75
5.75
5.75
5.75
5.75
5.75
6.25

AA=3"
9.020
11.22
14.22
15.18
15.18
19.68
19.68
-

BS
AA=4"
9.02
11.22
14.22
15.18
15.18
19.68
19.68
13.26
17.26
22.26
31.26

AA=(2) 4" AA=Blank
6.640
8.840
11.84
12.80
12.80
12.80
12.80
17.30
17.30
17.30
17.30
10.88
10.88
11.16
14.88
14.88
15.16
19.88
19.88
20.16
28.88
28.88

XZ
0.25
0.25
0.25
-

 For shipping weight add 15% to net weight.
10 	Refer to GE Energy for dimensions.
Conduit box will be assembled on the right hand side facing the commutator end
for motors, and on the left hand side facing the commutator end for generators.
Conduit box will be assembled on opposite side of frame, if so specified. Conduit box
may be oriented to accommodate customers’ application. Dimensions pertaining to
conduit boxes vary according to rating.
The standard single shaft machine has the commutator end bearing bracket and
shaft prepared to accept acessories. For additional information, see page 4.48.
Commutator end shaft extension is furnished only when specifically ordered, and is
prepared for accessory drive.

From 36C697106AA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.15

Accessories &
Modifications

AD

Outline
Dimensions

FU

O

U

Application
Information

AF

Other

FN-FW

XZ

Terms

.70

P

C

Frames 365ATD TO L508ATD

Dripproof Fully Guarded*, Splashproof
and Totally Enclosed Nonventilated

Type D-Flange Mounting with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
COMMUTATOR END

FC

AB

Motor Pricing

C
AG
.70
ACCESSORY
MOUNTING
FACE

FN-FW

BF DIA (8) HOLES
EQUALLY SPACED

AC

AH
BV

BD

BB

XN

P

XZ

BE

XZ

45°

FV
V

Modifications
Pricing

XL

AJ
U

AF
FU

Accessories &
Modifications
Outline
Dimensions
Application
Information

AE

W

AD

N

AD

D

FW
K (APPROX)

FN

Frame
365ATD
366ATD
368ATD
407ATD
L407ATD
409ATD
L409ATD
504ATD
L504ATD
506ATD
L506ATD
508ATD
L508ATD

Approx.
WK2 of Arm
Lb. Ft.2
15.610
18.270
22.210
35.470
35.540
43.810
43.880
79.100
79.150
98.760
98.810
121.87
122.92

Thick
0.625
0.625
0.625
0.625
0.625
0.625
0.625
0.750
0.750
0.750
0.750
0.750
0.750

Commutator
End Key
Lgth.
±.03
3.50
3.50
3.50
4.00
4.00
4.00
4.00
5.25
5.25
5.25
5.25
5.25
5.25

H DIA
(4) HOLES

2E
A

AIR
OUTLET

Drive End
Key
Width
0.625
0.625
0.625
0.625
0.625
0.625
0.625
0.750
0.750
0.750
0.750
0.750
0.750

J

G
E

AIR
OUTLET

BA

B

Approx.
Net Wt.
In Lb.
820.0
930.0
1090
1380
1430
1680
1730
2000
2170
2390
2540
2910
3070

HOLE(S) FOR
AA CONDUIT

BC

AIR
INLET
2F

Width
0.500
0.500
0.500
0.625
0.625
0.625
0.625
0.750
0.750
0.750
0.750
0.750
0.750

Thick
0.500
0.500
0.500
0.625
0.625
0.625
0.625
0.750
0.750
0.750
0.750
0.750
0.750

PG116
Lgth.
±.03
3.0
3.0
3.0
3.5
3.5
3.5
3.5
4.5
4.5
4.5
4.5
4.5
4.5

DIMENSIONS IN INCHES

A Max. B Max.
17.92 14.16
17.92 15.90
17.92 19.90
20.00 20.16
20.00 20.16
20.00 24.16
20.00 24.16
24.92 18.96
24.92 18.96
24.92 22.96
24.92 22.96
24.92 27.96
24.92 27.96

C
33.70
35.90
38.9
40.12
43.52
44.62
48.02
45.74
47.50
49.74
51.50
54.75
56.50

‡
D
9.00
9.00
9.00
10.0
10.0
10.0
10.0
12.5
12.5
12.5
12.5
12.5
12.5

E
7.0
7.0
7.0
8.0
8.0
8.0
8.0
10
10
10
10
10
10

2F
12.25
14.00
18.00
18.00
18.00
22.00
22.00
16.00
16.00
20.00
20.00
25.00
25.00

G
0.74
0.74
0.74
0.86
0.86
0.86
0.86
1.11
1.11
1.11
1.11
1.11
1.11

H
0.8125
0.8125
0.8128
0.9375
0.9375
0.9375
0.9375
1.1875
1.1875
1.1875
1.1875
1.1875
1.1875

J
3.26
3.26
3.26
4.00
4.00
4.00
4.00
4.50
4.50
4.50
4.50
4.50
4.50

K
2.31
2.31
2.31
2.38
2.38
2.38
2.38
3.00
3.00
3.00
3.00
3.00
3.00

N
4.92
4.92
4.92
5.42
5.42
5.42
5.42
6.67
6.67
6.67
6.67
6.67
6.67

O
17.91
17.91
17.91
20.15
20.15
20.15
20.15
25.15
25.15
25.15
25.15
25.15
25.15

AJ
20
20
20
22
22
22
22
30
30
30
30
30
30

AK
18
18
18
18
18
18
18
28
28
28
28
28
28

DIMENSIONS IN INCHES
Frame
365ATD
366ATD
368ATD
407ATD
L407ATD
409ATD
L409ATD
504ATD
L504ATD
506ATD
L506ATD
508ATD
L508ATD

P
17.90
17.90
17.90
20.38
20.38
20.38
20.38
25.38
25.38
25.38
25.38
25.38
25.38

U
2.375
2.375
2.375
2.625
2.625
2.625
2.625
3.250
3.250
3.250
3.250
3.250
3.250

∆
V
4.50
4.50
4.50
5.00
5.00
5.00
5.00
6.25
6.25
6.25
6.25
6.25
6.25

W
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17
0.17

BA
5.875
5.875
5.875
6.625
6.625
6.625
6.625
8.500
8.500
8.500
8.500
8.500
8.500

BB Max
0.25
0.25
0.25
0.19
0.19
0.19
0.19
0.19
0.19
0.19
0.19
0.19
0.19

BC
0.38
0.38
0.38
0.38
0.38
0.38

BD Max BE Nom
22
1
22
1
22
1
24
1
24
1
24
1
24
1
32
1
32
1
32
1
32
1
32
1
32
1

BF
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125
0.8125

XZ
1.8
1.8
1.8
1.8
1.8
1.8
1.8
2.2
2.2
2.2
2.2
2.2
2.2

FC
37.45
39.65
42.65
44.37
47.77
48.87
52.27
50.99
52.75
54.99
56.75
59.99
61.75

FN
4.45
4.45
4.45
4.95
4.95
4.95
4.95
5.95
5.95
5.95
5.95
5.95
5.95

FU
2.125
2.125
2.125
2.375
2.375
2.375
2.375
2.875
2.875
2.875
2.875
2.875
2.875

∆
FV
4.0
4.0
4.0
4.5
4.5
4.5
4.5
5.5
5.5
5.5
5.5
5.5
5.5

FW
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2

FN-FW
4.25
4.25
4.25
4.75
4.75
4.75
4.75
5.75
5.75
5.75
5.75
5.75
5.75

AG
28.95
31.15
34.15
34.87
38.27
39.37
42.77
38.86
40.62
42.86
44.62
47.86
49.62

AH
4.750
4.750
4.750
5.250
5.250
5.250
5.250
6.875
6.875
6.875
6.875
6.875
6.875

Terms

Other

O

AK

From 36C697106DA

4.16

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames 365AT TO 5010AY

Dripproof Fully Guarded*, Splashproof
and Totally Enclosed Nonventilated

Conduit Box Dimensions

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
CONDUIT BOX DIMENSIONS
BS
9.020
11.22
14.22
15.18
19.68

BV
14.9
17.1
20.1
21.8
26.3

BS
6.640
8.840
11.84
12.80
17.30

BV
12.52
14.72
17.72
19.42
23.92

BS
12.8
17.3

AA=4"

BV
19.42
23.92

Frame
504ATD
L504ATD
506ATD
L506ATD
508ATD
L508ATD

BS
13.26
17.26
22.26
-

AA=(2) 4"
BS
BV
10.88
19
14.88
23
19.88
28
-

BV
21.38
25.38
30.38
-

AA= Blank
BS
BV
10.88
19.00
11.16
19.28
14.88
23.00
15.16
23.28
19.88
28.00
20.16
28.26

DIMENSIONS IN INCHES

Frame
360AT
400AT
500AT
L500AT
5010AY

AB
16.08
17.47

AC
12.33
13.72

AA=3"
AE
AF
9.000 6.44
12.95 6.44

XL
10.12
10.12

XN
7
7

AB
17.82
19.22
21.70

AC
13.20
14.60
17.08

21.94

17.32

Not Available

AA=4"
AE
AF
9.00
8.5
12.95
8.5
16.10
8.5
Not Available
16.10
8.5

XL
13.5
13.5
13.5

XN
8.62
8.62
8.62

AB
18.72
20.12
22.60

AC
14.97
16.37
18.85

13.5

8.62

22.84

19.09

10

XL
13.5
13.5
13.5

XN
13.5
13.5
13.5

13.5

13.5

AA= Blank 13.38" X 13.31"
Available Drill Space
AE
AF
XL
Not Available
24.76 12.95 6.75
13.5
27.18 16.10 6.75
13.5
27.18 15.70 8.75
13.5
27.42 16.10 6.75
13.5
AB

XN
13.5
13.5
13.5
13.5

	Refer to GE Energy for dimensions.
Conduit box will be assembled on the right hand side facing the commutator end
for motors, and on the left hand side facing the commutator end for generators.
Conduit box will be assembled on opposite side of frame, if so specified. Conduit box
may be oriented to accommodate customers’ application. Dimensions pertaining to
conduit boxes vary according to rating.
The standard single shaft machine has the commutator end bearing bracket and
shaft prepared to accept acessories. For additional information, see page 4.48.
Commutator end shaft extension is furnished only when specifically ordered, and is
prepared for accessory drive.
Mounting face will be square and rabbet diameter concentric with shaft within 0.007
inch total indicator reading. "AK" dimensions: +0.000 inch -0.005 inch.

Terms

Other

Application
Information

* Dripproof, fully guarded machines can be used for wall or ceiling mounting
Assembly modifications must be made to maintain proper enclosure.
‡ Dimensions "D" will not be exceeded. When exact dimension is required, shims up
to .03 inches may be necessary where dimension "D" is 8 inches or less. When
dimension "D" is over 8 inches, shims up to .06 inch may be necessary.
Splashproof machines will have additional covers, increasing the overall width at the
commutator end and drive end side cover openings.
∆ “V” represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.

AA=(2) 4"
AE
AF
9.000 6.75
12.96 6.75
16.10 6.75
Not Available
3
16.10 6.75

AD
3
3
3

Modifications
Pricing

BV
14.9
17.1
20.1
21.8
26.3

Accessories &
Modifications

BS
9.020
11.22
14.22
15.18
19.68

AA= Blank

Outline
Dimensions

Frame
365AT
366AT
368AT
407AT
L407AT
409AT
L409AT

AA=(2) 4"

Motor Pricing

DIMENSIONS IN INCHES

AA=4"

AA=3"

From 36C697106DA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.17

Frames 365AT to L409AT

Totally Enclosed
Fan Cooled

with Feet

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
COMMUTATOR END
FC

Motor Pricing

XP

COMMUTATOR END

AB

0.93"

SHAFT COVER FOR
COMMUTATOR
END EXTENSION

AC

Modifications
Pricing
Accessories &
Modifications
Outline
Dimensions
Application
Information

FV

C
For Fig. 1
ACCESSORY MOUNTING FACE
AIR
OUTLET

N-W
V

XN
FU

FV

O

FU
AE

D

G

J

H HOLE

E

0.51"

AIR
INLET

SHAFT COVER
NO COMMUTATOR
END EXTENSION

0.51"

HOLE(S) FOR
AA CONDUIT

FN-FW

Frame
365AT
366AT
368AT
407AT
L407AT
409AT
L409AT

Frame
365AT
366AT
368AT
407AT
L407AT
409AT
L409AT

O
17.91
17.91
17.91
20.15
20.15
20.15
20.15

P
17.9
17.9
17.9
20.38
20.38
20.38
20.38

W
N

BS

FN

2F

BA
B

Approx.
WK2 of Arm
Lb. Ft.2
15.61
18.27
22.21
35.47
35.54
43.81
43.88

Approx.
Net Wt.
In Lb.
830.0
940.0
1100
1380
1430
1680
1730

AD
AD
K approx

FN-FW

A

U

XL

AF

AIR
INLET

2E

U
2.375
2.375
2.375
2.625
2.625
2.625
2.625

pg121

Drive End
Key
Width
0.625
0.625
0.625
0.625
0.625
0.625
0.625

∆
V
4.5
4.5
4.5
5.0
5.0
5.0
5.0

Thick
0.625
0.625
0.625
0.625
0.625
0.625
0.625

W
0.17
0.17
0.17
0.17
0.17
0.17
0.17

Commutator
End Key
Lgth.
±.03
3.5
3.5
3.5
4.0
4.0
4.0
4.0

N-W
4.75
4.75
4.75
5.25
5.25
5.25
5.25

Width
0.500
0.500
0.500
0.625
0.625
0.625
0.625

BA
5.875
5.875
5.875
6.625
6.625
6.625
6.625

FC
42.47
44.67
47.67
49.39
52.79
53.89
57.29

Thick
0.500
0.500
0.500
0.625
0.625
0.625
0.625

FN
5.42
5.42
5.42
5.42
5.42
5.42
5.42

DIMENSIONS IN INCHES
Lgth.
±.03
3.0
3.0
3.0
3.5
3.5
3.5
3.5

A Max.
17.92
17.92
17.92
20.00
20.00
20.00
20.00

B Max.
14.16
15.90
19.90
20.16
20.16
24.16
24.16

DIMENSIONS IN INCHES
∆
FU
FV
FW
2.125
4.0
1.17
2.125
4.0
1.17
2.125
4.0
1.17
2.375
4.5
0.67
2.375
4.5
0.67
2.375
4.5
0.67
2.375
4.5
0.67

C
38.22
40.42
43.42
44.90
48.30
49.40
52.80

‡
D
9.0
9.0
9.0
10
10
10
10

FN-FW
4.25
4.25
4.25
4.75
4.75
4.75
4.75

XO
18.62
18.62
18.62
19.62
19.62
19.62
19.62

E
7
7
7
8
8
8
8

2F
12.25
14.00
18.00
18.00
18.00
22.00
22.00

G
0.74
0.74
0.74
0.86
0.86
0.86
0.86

H
0.8125
0.8125
0.8125
0.9375
0.9375
0.9375
0.9375

J
3.26
3.26
3.26
4.00
4.00
4.00
4.00

K
2.31
2.31
2.31
2.38
2.38
2.38
2.38

N
4.92
4.92
4.92
5.42
5.42
5.42
5.42

BS
XP
19.24
19.24
19.24
19.24
19.24
19.24
19.24

AA=3"
9.020
11.22
14.22
15.18
15.18
19.68
19.24

AA=4"
9.020
11.22
14.22
15.18
15.18
19.68
19.24

AA= (2) 4"
6.640
8.840
11.84
12.80
12.80
17.30
17.30

AA= Blank

12.8
12.8
17.3
17.3

DIMENSIONS IN INCHES

Frame
360AT
400AT

Other

FW

SHAFT COVER FOR
COMMUTATOR
END EXTENSION

FW

XO

Terms

FC

C
For Fig. 2

P

AB
16.08
17.47

AC
12.33
13.72

AA=3"
AE
AF
9.000 6.44
12.95 6.44

XL
10.12
10.12

XN
7
7

AB
17.82
19.22

AC
13.2
14.6

AA=4"
AE
AF
9.000
8.5
12.95
8.5

XL
13.5
13.5

‡ Dimensions "D" will not be exceeded. When exact dimension is required, shims up
to .03 inches may be necessary where dimension "D" is 8 inches or less. When
dimension "D" is over 8 inches, shims up to .06 inch may be necessary.
∆ “V” represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.

XN
8.62
8.62

AB
18.72
20.12

AC
14.97
16.37

AD
3
3

AA=(2) 4"
AE
AF
9.000 6.75
12.95 6.75

XL
13.5
13.5

XN
13.5
13.5

AA= Blank 13.38" X 13.31"
Available Drill Space
AE
AF
XL
XN
Not Available
24.76 12.95 6.75
13.5
13.5
AB

 For shipping weight add 15% to net weight.
10 	Refer to GE Energy for dimensions.
Conduit box will be assembled on the right hand side facing the commutator end
for motors, and on the left hand side facing the commutator end for generators.
Conduit box will be assembled on opposite side of frame, if so specified. Conduit box
may be oriented to accommodate customers’ application. Dimensions pertaining to
conduit boxes vary according to rating.
Commutator end shaft extension is furnished only when specifically ordered, and is
prepared for accessory drive.
The standard single shaft machine has the commutator end bearing bracket and
shaft prepared to accept acessories. For additional information, see page 4.48.

From 36C697106BA

4.18

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Explosionproof

Totally Enclosed Nonventilated
and Fan Cooled

Frames 188AT to 409AT

General
Information

Type CD

Drive End
Key
Depth
0.12
0.12
0.16
0.25
0.25
0.31
0.31

DIMENSIONS IN INCHES
Lgth.
±.03
1.38
1.38
1.75
2.50
3.00
4.00
4.00

A
9.000
9.000
10.40
13.88
15.88
20.00
20.00

B
10.50
11.50
14.06
15.66
17.96
20.00
24.00

TENV
C
19.76
21.76
28.50
-

TEFC
C
21.82
28.50
33.74
35.88
43.12
47.62

‡
D
4.50
4.50
5.25
7.00
8.00
10.0
10.0

E
3.75
3.75
4.25
5.50
6.25
8.00
8.00

2E
7.50
7.50
8.50
11.0
12.5
16.0
16.0

2F
9.00
10.0
12.5
14.0
16.0
18.0
22.0

G
0.56
0.56
0.56
0.69
0.75
0.86
0.86

H
0.406
0.406
0.406
0.531
0.656
0.938
0.938

J
1.75
1.75
2.00
2.50
3.00
4.00
4.00

K
1.62
1.62
2.10
2.00
2.34
2.38
2.38

N
2.38
2.38
2.81
3.91
4.41
5.44
5.44

TENV
O
9.000
9.000
10.56
-

TEFC
O
9.520
11.10
14.68
16.68
20.76
20.76

TENV
P
9.00
9.00
10.5
-

TEFC
P
10.88
11.70
15.25
17.25
21.56
21.56

Outline
Dimensions

Approx.
Approx.
Net Wt. WK2 of Arm
Frame In Lb.
Width
Lb. Ft.2
188AT
150.0
0.45
0.250
189AT
180.0
0.67
0.250
2110AT 340.0
1.71
0.312
288AT
655.0
5.36
0.500
328AT
920.0
9.67
0.500
407AT
1550
35.5
0.625
409AT
1850
43.8
0.625

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

U
1.125
1.125
1.375
1.875
2.125
2.625
2.625

W
0.12
0.12
0.06
0.16
0.16
0.19
0.19

N-W
2.26
2.26
2.75
3.75
4.25
5.25
5.25

BA
2.74
2.74
3.50
4.75
5.25
6.62
6.62

BS
1.960
1.960
3.250
3.000
3.125
17.56
22.06

AA
1.00
1.00
1.25
2.00
2.00
3.00
3.00

AB
8.940
8.940
10.50
13.75
14.75
20.22
20.22

AF
3.60
3.60
4.25
5.25
5.25
4.69
4.69

XL
5.32
6.82
6.82
9.38
9.38

XN
3.50
3.50
4.28
5.75
5.75
9.38
9.38

XP
10.88
10.88
12.80
16.12
16.50
-

ZA
2.12
2.62
3.50
-

ZB
1.62
1.62
2.16
-

ZC
7.600
9.600
11.50
13.88
14.88
3.090
3.090

Conduit box will be assembled on the right hand side facing the commutator end for
motors, and on the left hand side facing the commutator end for generators. Conduit
box will be assembled on opposite side of frame, if so specified. Conduit box may be
oriented to accommodate customers’ application. Dimensions pertaining to conduit
boxes vary according to rating.

Terms

‡ Dimensions "D" will not be exceeded. When exact dimension is required, shims up
to .03 inches may be necessary where dimension "D" is 8 inches or less. When
dimension "D" is over 8 inches, shims up to .06 inch may be necessary.
∆ "V" represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.
 For shipping weight add 15% to net weight.

AC
6.780
6.780
8.120
10.12
11.12
15.52
15.52

Other

Frame
188AT
189AT
2110AT
288AT
328AT
407AT
409AT

Application
Information

DIMENSIONS IN INCHES
∆
V
2.26
2.26
2.50
3.50
4.00
5.25
5.25

From 796C710AA, 36B550045BA, 36B549871BA, 36B550747AA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.19

Explosionproof C-Face
Frames 188AT to 189AT with Feet

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

FIGUrE 1
Drive End
Approx. Approx.
Net
WK2 of
Arm
Wt.
Frame In Lb. Lb. Ft.2 Width
Fig 1
188ATC 160
0.45
0.25
189ATC 190
0.67
0.25
Fig 2
188ATC 160
0.45
0.188
189ATC 190
0.67
0.188

DIMENSIONS IN INCHES

Key
Lgth.
Depth ±.03 A

Other
Terms

Class II,
Group E, F and G

Class I, Group D
TENV TEFC
C
C

B

‡
D

E

2E 2F

G

H

J

K

TENV TEFC TENV TEFC
O
O
P
P

N

∆
V

U

W

∆
V

N-W BA

W N-W BA AA AB

0.125 1.38 9 10.5 19.76
4.5 3.75 7.5 9 0.56 0.4062 2 1.62 2.38
0.125 1.38 9 11.5 21.76 21.82 4.5 3.75 7.5 10 0.56 0.4062 2 1.62 2.38

9
9

9.52

9
9

- 1.125 2.26 0.13 2.25 2.75 1.62 0.5 1.88 3.12 1 8.94
10 1.125 2.26 0.13 2.25 2.75 1.62 0.5 1.88 3.12 1 8.94

0.094 1.38 9 10.5 19.76
4.5 3.75 7.5 9 0.56 0.4062 2 1.62 2.38
0.094 1.38 9 11.5 21.76 21.82 4.5 3.75 7.5 10 0.56 0.4062 2 1.62 2.38

9
9

9.52

9
9

- 0.875 1.62
10 0.875 1.62

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

Frame
Cont'd

Fig 1
188ATC
189ATC
Fig 2
188ATC
189ATC

AC

AG
AG
AF TENV TEFC AH

AJ

AK BB

DIMENSIONS IN INCHES
BF
BD
BC Max
Tap
No. Depth

6.78 3.6 17.64
- 2.12 7.25 8.5 0.3 0.13 8.78
6.78 3.6 19.64 19.7 2.12 7.25 8.5 0.3 0.13 8.78
6.78 3.6 17.64
- 2.12 5.875 4.5 0.13
6.78 3.6 19.64 19.7 2.12 5.875 4.5 0.13

0.5
0.5

-

1.88 3.12 1.62 0.5 1.88 3.12 1 8.94
1.88 3.12 1.62 0.5 1.88 3.12 1 8.94

BS

XL

XN

XP

ZA

ZB

ZC

.50-13
.50-13

4
4

0.75
0.75

1.96 4.5 3.5
1.96 4.5 3.5

10.88
10.88

2.62
2.62

1.88
1.88

7.6
9.6

7.14 .375-16
7.14 .375-16

4
4

0.75
0.75

1.96 4.5 3.5
1.96 4.5 3.5

10.88
10.88

2.62
2.62

1.88
1.88

7.6
9.6

FIGUrE 2
‡ Dimensions "D" will not be exceeded. When exact dimension is required, shims
up to.03 inches may be necessary where dimension "D" is 8 inches or less. When
dimension "D" is over 8 inches, shims up to .06 inch may be necessary.
∆ "V" represents minimum length of shaft available for hubs.
Shaft diameters 1.5 inches and smaller will come within the limits of +0.0000 inch
-0.0005 inch. Diameters larger than 1.5 inches will come within the limits of +0.0000
inch -0.0010 inch. Shaft runout on diameters 1.625 inches and smaller shall not
exceed .002 inch indicator reading. Diameters larger than 1.625 inches shall not
exceed .003 inch indicator reading.
 For shipping weight add 15% to net weight.

Conduit box will be assembled on the right hand side facing the commutator end for
motors, and on the left hand side facing the commutator end for generators. Conduit
box will be assembled on opposite side of frame, if so specified. Conduit box may be
oriented to accommodate customers’ application. Dimensions pertaining to conduit
boxes vary according to rating.
For frames CD2110AT and CD288AT the rabbet diameter will be concentric with the
shaft within .004 inches and the mounting face will be square with the shaft within
.004 inch tolerance on "AK" dimension +.000 inch -.003 inch.
For frames 328 the rabbet diameter will be concentric with the shaft within .007
inches and the mounting face will be square with the shaft within .007 inch
tolerance on "AK" dimension +.000 inch -.005 inch.

From 36C697570AA

4.20

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

TEAAC

Totally Enclosed
Air-To-Air Cooled

Frames 366AT to L508AT

General
Information

Type CD

Cooler
Weight
in Lb.
230
252
425
425
440
440
425
430
435
445
460
470
610
610
610
625
660
675

XA
20.24
20.24
24.00
24.00
24.00
24.00
24.00
24.00
24.00
24.00
24.00
24.00
30.62
30.62
30.62
30.62
30.62
30.62

XB
10.12
10.12
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
15.31
15.31
15.31
15.31
15.31
15.31

XC
31.44
34.44
37.88
37.88
42.38
42.38
37.88
39.62
41.88
43.62
46.88
48.62
43.50
43.50
43.50
45.25
48.50
50.25

XD
33.70
33.70
36.96
36.96
36.96
36.96
41.06
41.06
41.06
41.06
41.06
41.06
47.88
47.88
47.88
47.88
47.88
47.88

XE
27.30
27.30
29.65
29.65
29.65
29.65
33.75
33.75
33.75
33.75
33.75
33.75
38.50
38.50
38.50
38.50
38.50
38.50

XF
6.29
6.29
6.88
6.88
6.88
6.88
8.75
8.75
8.75
8.75
8.75
8.75
8.53
8.53
8.53
8.53
8.53
8.53

XG
0.88
0.88
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.18
1.18
1.18
1.18
1.18
1.18

XH
12.92
12.92
15.88
15.88
15.88
15.88
15.88
15.88
15.88
15.88
15.88
15.88
19.12
19.12
19.12
19.12
19.12
19.12

XJ
11.70
11.70
13.75
13.75
13.75
13.75
13.75
13.75
13.75
13.75
13.75
13.75
17.19
17.19
17.19
17.19
17.19
17.19

XK
3.44
3.44
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50
5.50

XL
6.60
6.60
7.62
7.62
7.62
7.62
7.62
7.62
7.62
7.62
7.62
7.62
8.75
8.75
8.75
8.75
8.75
8.75

XM
2.5
2.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5

XN
0.75
0.75
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25

XW
8.740
8.740
11.00
11.00
11.00
11.00
11.00
11.00
11.00
11.00
11.00
11.00
13.25
13.25
13.25
13.25
13.25
13.25

XY
18.75
18.75
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
12.00
15.00
15.00
15.00
15.00
15.00
15.00

XZ
10.38
10.38
11.00
11.00
11.00
11.00
11.00
11.00
11.00
11.00
11.00
11.00
13.50
13.50
13.50
13.50
13.50
13.50

Application
Information

Cooler
Type
Z
Z
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B

Other

Frame
CD366AT
CD368AT
CD407AT
L407AT
CD409AT
L409AT
CD504AT
L504AT
CD506AT
L506AT
CD508AT
L508AT
CD504AT
L504AT
CD506AT
L506AT
CD508AT
L508AT

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Terms

Standard location of cooler conduit box is on the same side as machine conduit box,
however, box will be located on opposite side if specified.
Providing mounting conditions permit, conduit box may be turned so that entrance can
be made upward, downward, or horizontally.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.21

TEAAC

Totally Enclosed
Air-To-Air Cooled

Frames 5010AY

Approximate cooler weight
Aluminum 950 lbs
Stainless Steel 1209 lbs

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

4.22

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames 327AT to L508AT

Totally Enclosed
Air-Over-Frame

General
Information

Type CD

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Locations of Blowers shown
are preferred locations
Blower can be rotated about
blower axis to any position
in 90° increments where
conditions permit.

Accessories &
Modifications

Modifications
Pricing

N.A. = Not Applicable

Outline
Dimensions

Locations of Blowers shown
are preferred locations
Blower can be rotated about
blower axis to any position
in 90° increments where
conditions permit.

Application
Information

N.A. = Not Applicable

XA
16.40
16.40
18.40
18.40
18.40
20.00
20.00
20.00
20.00
25.24
25.24
25.24
25.24

XB
0.32
0.32
0.42
0.42
0.42
0.42
0.42
0.42
0.42
0.45
0.45
0.45
0.45

XC
9.260
9.260
10.22
10.22
10.22
11.22
11.22
11.22
11.22
13.73
13.73
13.73
13.73

XD
2.68
2.68
1.45
1.45
1.45
1.45
1.45
1.45
1.45
N.A.
N.A.
N.A.
N.A.

XE
17.98
19.86
16.11
18.42
21.42
21.42
21.42
25.92
25.92
21.29
25.29
30.29
32.05

XF
1.56
1.56
2.61
2.61
2.61
2.61
2.61
2.61
2.61
2.60
2.60
2.60
2.60

XG
6.250
6.250
7.480
7.480
7.480
7.380
10.78
7.380
10.78
11.20
11.39
11.39
11.39

XH
14.52
14.52
15.23
15.23
15.23
15.23
16.23
16.23
16.23
20.04
20.04
20.04
20.04

XJ
19.08
19.08
19.73
19.73
19.73
20.73
20.73
20.73
20.73
28.47
28.47
28.47
28.47

XK
4.88
4.88
4.90
4.90
4.90
4.90
4.90
4.90
4.90
8.53
8.53
8.53
8.53

XL
10.38
10.38
10.51
10.51
10.51
10.51
10.51
10.51
10.51
11.85
11.85
11.85
11.85

XM
8.880
8.880
8.780
8.780
8.780
8.780
8.780
8.780
8.780
14.91
14.91
14.91
14.91

XN
3.15
3.15
3.38
3.38
3.38
3.38
3.38
3.38
3.38
4.37
4.37
4.37
4.37

XP
5.630
7.050
5.860
5.860
5.860
5.810
5.810
5.810
5.810
4.820
8.820
13.82
13.82

Xr
2.81
2.81
2.82
2.82
2.82
2.82
2.82
2.82
2.82
5.57
5.57
5.57
5.57

XS
10.72
12.59
7.780
8.880
10.38
11.24
11.24
13.49
13.49
11.02
15.02
20.02
20.02

XT
15.45
15.90
14.46
16.66
19.66
19.61
23.01
24.11
27.51
23.30
23.49
23.49
25.25

XU
17.65
17.65
17.98
17.98
17.98
19.51
19.51
19.51
19.51
27.36
27.36
27.36
27.36

XV
13.09
13.09
14.23
14.23
14.23
15.01
15.01
15.01
15.01
19.93
19.93
19.93
19.93

XW
9.070
9.070
9.840
9.840
9.840
10.84
10.84
10.84
10.84
13.93
13.93
13.93
13.93

From 36C697331AA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.23

Other

DIMENSIONS IN INCHES

Terms

Frame
CD327AT
CD328AT
CD365AT
CD366AT
CD368AT
CD407AT
CDL407AT
CD409AT
CDL409AT
CD504AT
CD506AT
CD508AT
CDL508AT

Approx.
Net
Wt.
in Lb.
33
60
54
56
59
60
60
70
70
75
84
89
92

Dimensions, Air Openings
Frames 210AT to 5010AY

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Modifications
Pricing

Motor Pricing

General
Information

Type CD

FIGUrE 2

Accessories &
Modifications

FIGUrE 1

Application
Information

Outline
Dimensions

FIGUrE 3

DIMENSIONS IN INCHES
Frame
CD210AT
CD258AT
CD259AT
CD287AT
CD288AT
CD320AT
CD360AT
CD400AT
CDL400AT
CD500AT
CDL500AT
CD5010AY

Figure No.
1

CA
4.59

CB
3.24

CC
2.38

CD
0.50

CE
2.62

CF
0.34

CG

-

DA
6.710

DB
5.400

DC
4.20

DD
0.50

DE
4.42

DF
0.34

DG
5.00

DJ
5.640

DK
4.42

DL
0.61

DM
-

1

5.03

3.52

2.38

0.48

2.62

0.34

-

6.610

5.140

4.20

0.48

4.42

0.34

6.00

6.760

5.42

0.67

-

1

5.53

3.94

2.88

0.58

3.32

0.34

-

8.210

6.440

5.00

0.68

5.50

0.40

7.00

7.760

6.22

0.77

-

1
2
3
3

5.85
6.30
6.98
6.98

4.12
4.80
5.22
5.22

2.88
3.06
3.19
3.19

0.58
0.81
0.77
0.77

3.32
3.70
3.70
3.70

0.34
0.56
0.46
0.46

-

7.950
9.600
9.120
12.52

6.300
7.860
7.240
10.64

5.00
5.44
5.44
7.74

0.68
0.76
0.72
0.72

5.50
5.80
5.80
8.20

0.40
0.62
0.56
0.56

8.00
10.4
10.4
10.4

8.760
11.30
12.74
12.74

7.22
9.24
4.62
4.62

0.77

4
5
5

0.78
0.78

2
5
4

3

8.18

5.96

3

8.40

5.90

4.26

0.94

5.00

0.54

8

13.48

11.42

9.36

0.86

9.80

0.64

12.8

14.70

5.14

0.88

4

4.26

0.82

5.00

0.44

0

13.48

11.42

9.36

0.86

9.80

0.64

12.8

14.70

5.14

0.88

4

Terms

Other

 For shipping weight add 15% to net weight.

From 533C118AA

4.24

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Blower Unit, Commutator End Mounted
Frames CD180AT to CD280AT

General
Information

Type CD

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Application
Information

Outline
Dimensions

Accessories &
Modifications

CD180AT

DIMENSIONS IN INCHES

Type CD Frame

Approx. Net
Wt. in Lb.

XA

XB

XD

XE

XF

XJ

XK

XM

XS

210AT*

20

17.61

12.36

14.62

10.76

9.520

5.32

6.88

2.38

6.680

250AT*

20

19.61

13.36

14.62

10.66

9.520

5.32

6.88

2.38

6.680

280AT

28

23.10

16.10

21.82

15.34

13.53

6.82

6.88

2.81

10.38

* On CD210AT & CD250AT frames, when sidemounted, blower can only be mounted
opposite conduit box.

www.gemotors.com

•

800-541-7191

NOTE: The required air flow is obtained only when the blower motors are operated in
the correct direction of rotation. When facing the air inlet, the blower wheel should
rotate counterclockwise. Check the blower motor for correct direction of rotation by
running it in both directions and observing the quantity of air discharged. The direction
of rotation which gives the greatest air flow is the correct one. Blower motors can be
reversed by interchanging the external connections to any two of the three line leads.

GEP387M 09/11 • Prices and data subject to change without notice.

4.25

Terms

Other

CD210AT-280AT

Blower Unit, Commutator End Mounted
Frames 320AT

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

DIMENSIONS IN INCHES

Approx. Net
Wt. in Lb.

XA

XB

XD

XE

XF

XJ

XK

XM

XS

XT

320AT

61

27.87

19.87

22.94

16.95

14.75

10.2

13.38

4.49

12.17

0.53

Type CD Frame

Approx. Net
Wt. in Lb.

XA

XB

XD

XE

XF

XJ

XK

XM

XS

XT

320AT

65

27.81

19.87

22.94

7.39

14.75

10.2

13.38

4.49

12.17

0.53

Terms

Other

Application
Information

Outline
Dimensions

Type CD Frame

DIMENSIONS IN INCHES

NOTE: The required air flow is obtained only when the blower motors are operated in
the correct direction of rotation. When facing the air inlet, the blower wheel should
rotate counterclockwise. Check the blower motor for correct direction of rotation by

running it in both directions and observing the quantity of air discharged. The direction
of rotation which gives the greatest air flow is the correct one. Blower motors can be
reversed by interchanging the external connections to any two of the three line leads.

36A167799HN, 36A167799HS, 36A167799HT

4.26

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Blower Unit, Commutator End Mounted
Frames 360AT to 400AT

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

XB

XD

XE Fig. 1

XE Fig. 2

CD360AT

65

28.80

19.80

23.06

18.13

6.51

CD400AT

65

30.52

20.52

23.19

17.69

7.09

CDL400AT

70

30.52

20.52

23.19

19.87

4.91

DIMENSIONS IN INCHES

Type
CD Frame

XJ

XK

XM

XS

XT

XF

CD360AT

8.93

13.38

3.22

12.09

1.8

14.90

CD400AT

8.93

13.38

3.22

12.04

1.8

15.07

CDL400AT

8.93

13.38

3.22

12.03

1.8

15.07

Frame
CD360AT
CD400AT

Blower Motor Conduit Hole
.875 Diameter Hole in Blower Motor CND Box

FIGUrE 2 SIDE MOUNTED
rIGHT HAND SIDE
FACING COMMUTATOr END

Terms

Other

Application
Information

From 36A167799HP

Outline
Dimensions

NOTE: The required air flow is obtained only when the blower motors are operated
in the correct direction of rotation. When facing the air inlet, the blower wheel
should rotate clockwise. Check the blower motor for correct direction of rotation
by running it in both directions and observing the quality of air discharged. The
direction of rotation which gives the greatest air flow is the correct one. Blower
motors can be reversed by interchanging the external connections to any two of
three line leads.

Motor Pricing

XA

Modifications
Pricing

FIGUrE 1 TOP MOUNTED

Approx. Net
Wt. in Lb.

Accessories &
Modifications

From 36A167799HM

DIMENSIONS IN INCHES

Type
CD Frame

FIGUrE 3 SIDE MOUNTED
LEFT HAND SIDE
FACING COMMUTATOr END

From 36A167799HR

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.27

Blower Unit, Commutator End Mounted
Frames 500AT

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
DIMENSIONS IN INCHES

Type
CD Frame

Approx. Net
Wt. in Lb.

XA

XB

XD

XE Fig. 1

XE Fig. 2

CD500AT

83

43.05

30.55

32.58

22.95

8.35

DIMENSIONS IN INCHES

Type
CD Frame

XJ

XK

XM

XS

XT

XF

CD500AT

15.17

20.36

6.47

15.65

1.25

20.43

Frame

Blower Motor Conduit Hole

CD500AT

1.09" Diameter Hole in Blower Motor CND Box

NOTE: The required air flow is obtained only when the blower motors are operated
in the correct direction of rotation. When facing the air inlet, the blower wheel
should rotate counterclockwise. Check the blower motor for correct direction of
rotation by running it in both directions and observing the quality of air discharged.
The direction of rotation which gives the greatest air flow is the correct one. Blower
motors can be reversed by interchanging the external connections to any two of
three line leads.

From 36A167799GK

FIGUrE 1 TOP MOUNTED

From 36A167799GN

FIGUrE 2 SIDE MOUNTED
rIGHT HAND SIDE
FACING COMMUTATOr END

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

FIGUrE 3 SIDE MOUNTED
LEFT HAND SIDE
FACING COMMUTATOr END

From 36A167799GL

4.28

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames 6050 to 6066

Dripproof Fully Guarded, Separately Ventilated
and Enclosed Separately Ventilated

General
Information

Type CD

B

2F

C

CD6050

3900

160

42.7

32

59.71

CD6052

4200

180

44.8

36

CD6054

4100

170

47.0

CD6055

4700

210

47.4

CD6057

4500

190

CD6058

5300

CD6059

5000

CD6062
CD6063
CD6066

FC

Standard
Box

Oversize
Box

Frame

66.96

16.59

14.59

CD6050

61.81

69.06

18.69

16.69

CD5052

36

64.01

71.26

14.59

13.59

CD6055

36

64.41

71.66

21.29

19.29

CD6058

49.1

40

66.11

73.36

16.69

15.69

CD6062

240

50.6

40

67.61

74.86

24.49

22.49

CD6054

220

51.7

40

68.71

75.96

19.29

18.29

CD6057

6000

280

54.6

45

71.61

78.86

28.49

26.49

CD6059

5600

250

54.9

45

71.91

79.16

22.49

21.49

CD6063

6300

290

58.9

50

75.91

83.16

26.49

25.49

CD6066

AB

AF

XA

Standard

31.72

10

20

Oversize

35.75

12

24

Standard

35.72

12

24

Oversize

39.72

13

26

Splashproof machines will have additional covers, but all dimensions will remain
the same.
Air inlet can be provided at drive end at top, bottom, or either side if so specified.
Totally enclosed separately ventilated enclosures can be provided with both air inlet
and outlet at top, bottom, or either side.
 For shipping weight, add 15% to net weight.

Terms

Other

Commutator end shaft extension is furnished only when specifically ordered.
Standard conduit box location is right hand side for motor and left hand side for
generator facing commutator end. Conduit box can be assembled on the oppo site
side of frame, or assembled so that entrance can be made from above, from
commutator end, or from drive end if so specified. Fixed termination is provided for
customer connections.

Box

Outline
Dimensions

Frame

Approx. Wk2
of Armature
Ft. Lb.

Application
Information

CONDUIT BOX DIMENSIONS

BS

Approx.
Net Wt.
in Lb.

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36C706021AA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.29

Frames 6154 to 6177

Dripproof Fully Guarded, Separately Ventilated
and Enclosed Separately Ventilated

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

CONDUIT BOX DIMENSIONS

BS

Frame

Approx.
Net Wt.
in Lb.

Approx. Wk2
of Armature
Ft. Lb.

B

2F

C

CD6154

5800

390

46.8

36

65.61

CD6157

6500

440

49.4

40

CD6160

7300

510

52.6

CD6163

6300

420

55.4

CD6164

8300

600

CD6165

7000

CD6168

7800

CD6169
CD6173
CD6177

FC

Standard
Box

Oversize
Box

Frame

74.06

20.79

18.79

CD6154

68.21

76.66

23.39

21.39

CD6157

42

71.41

79.86

26.59

24.59

CD6160

45

74.21

82.66

19.79

16.79

CD6164

56.6

45

75.41

83.86

30.59

28.59

CD6169

480

58.0

48

76.81

85.26

22.39

19.39

CD6163

550

61.2

50

80.01

88.46

25.59

22.59

CD6165

9500

700

61.2

50

80.01

88.46

35.19

33.19

CD6168

8800

640

65.2

56

84.01

92.46

29.59

26.59

CD6173

10000

740

69.8

60

88.61

97.06

34.19

31.19

CD6177

Commutator end shaft extension is furnished only when specifically ordered.
Standard conduit box location is right hand side for motor and left hand side for
generator facing commutator end. Conduit box can be assembled on the opposite
side of frame, or assembled so that entrance can be made from above, from
commutator end, or from drive end if so specified. Fixed termination is provided for
customer connections.

Box

AB

AF

XA

Standard

34.32

10

20

Oversize

38.32

12

24

Standard

38.32

12

24

Oversize

42.32

15

26

Splashproof machines will have additional covers, but all dimensions will remain
the same.
Air inlet can be provided at drive end at top, bottom, or either side if so specified.
Totally enclosed separately ventilated enclosures can be provided with both air inlet
and outlet at top, bottom, or either side.
 For shipping weight, add 15% to net weight.

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

From 36C706022AA

4.30

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames 6259 to 6280

Dripproof Fully Guarded, Separately Ventilated
and Enclosed Separately Ventilated

General
Information

Type CD

B

2F

C

CD6259

9800

960

51.7

40

71.71

CD6262

11100

1120

54.9

45

CD6266

12700

1320

58.9

CD6268

10400

1020

60.3

CD6270

11700

1180

CD6271

14500

1550

CD6275

13300

CD6280

15200

FC

Standard
Box

Oversize
Box

Frame

81.960

24.89

22.89

CD6259

74.91

85.160

28.09

26.09

CD6262

50

78.91

89.160

32.09

30.09

CD6266

50

80.31

90.560

23.89

20.89

CD6271

63.5

52

83.51

93.760

27.09

24.09

CD6268

63.5

52

83.51

93.760

36.69

34.69

CD6270

1380

67.5

56

87.51

97.760

31.09

28.09

CD6275

1610

72.1

63

92.11

102.36

35.69

32.69

CD6280

AB

AF

XA

38.22

10

20

Oversize

42.22

12

24

Standard

42.22

12

24

Oversize

46.22

15

30

Splashproof machines will have additional covers, but all dimensions will remain
the same.
Air inlet can be provided at drive end at top, bottom, or either side if so specified.
Totally enclosed separately ventilated enclosures can be provided with both air inlet
and outlet at top, bottom, or either side.
 For shipping weight, add 15% to net weight.

Terms

Other

Commutator end shaft extension is furnished only when specifically ordered.
Standard conduit box location is right hand side for motor and left hand side for
generator facing commutator end. Conduit box can be assembled on the opposite
side of frame, or assembled so that entrance can be made from above, from
commutator end, or from drive end if so specified. Fixed termination is provided for
customer connections.

Box
Standard

Outline
Dimensions

Frame

Approx. Wk2
of Armature
Ft. Lb.

Application
Information

CONDUIT BOX DIMENSIONS

BS

Approx.
Net Wt.
in Lb.

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36C706023AA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.31

Frames 6766 to 6785

Dripproof Fully Guarded, Separately Ventilated
and Enclosed Separately Ventilated

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

BS

Frame

Approx.
Net Wt.
in Lb.

Approx. Wk2
of Armature
Ft. Lb.

B

2F

C

CD6766

12100

1550

55.18

45

80.98

CD6770

14000

1850

58.68

50

CD6771

12400

1650

59.48

50

CD6774

15200

2200

62.68

CD6776

14000

1950

62.98

CD6778

15600

2300

CD6779

17200

CD6785

17600

CONDUIT BOX DIMENSIONS

FC

Standard
Box

Oversize
Box

Frame

93.930

23.67

20.67

CD6766

84.48

97.430

27.17

24.17

CD6770

85.28

98.230

23.67

20.67

CD6771

55

88.48

101.43

31.17

28.17

CD6774

55

88.78

101.73

27.17

24.17

CD6776

66.98

60

92.78

105.73

31.17

28.17

CD6778

2700

67.68

60

93.48

106.43

36.17

33.17

CD6779

2750

71.98

65

97.78

110.73

36.17

33.17

CD6785

Commutator end shaft extension is furnished only when specifically ordered.
Standard conduit box location is right hand side for motor and left hand side for
generator facing commutator end. Conduit box can be assembled on the opposite
side of frame, or assembled so that entrance can be made from above, from
commutator end, or from drive end if so specified. Fixed termination is provided
for customer connections.

Box

AB

AF

XA

Standard

43.75

12

24

Oversize

47.75

15

30

Splashproof machines will have additional covers, but all dimensions will remain
the same.
Air inlet can be provided at drive end at top, bottom, or either side if so specified.
Totally enclosed separately ventilated enclosures can be provided with both air inlet
and outlet at top, bottom, or either side.
 For shipping weight, add 15% to net weight.

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

From 36C706024AA

4.32

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Frames 6873 to 6896

Dripproof Fully Guarded, Separately Ventilated
and Enclosed Separately Ventilated

General
Information

Type CD

B

2F

C

CD6873

16000

2900

58.9

50

87.630

CD6876

17700

3230

62.9

55

CD6881

20300

4170

67.4

CD6882

16800

3130

67.5

CD6885

18500

3460

CD6887

23500

CD6890
CD6896

CONDUIT BOX DIMENSIONS

FC

Standard
Box

Oversize
Box

Frame

100.58

30.8

27.8

CD6873

91.630

104.58

34.8

31.8

CD6876

60

96.130

109.08

39.3

36.3

CD6881

60

96.230

109.18

27.8

24.8

CD6887

71.5

65

100.23

113.18

31.8

28.8

CD6882

5480

72.9

65

101.63

114.58

44.8

41.8

CD6885

21000

4400

76.0

70

104.73

117.68

36.3

33.3

CD6890

24200

5710

81.5

75

110.23

123.18

41.8

38.8

CD6896

AB

AF

XA

Standard

46.75

12

24

Oversize

50.75

15

30

Standard

50.75

15

30

Oversize

56.75

18

36

Splashproof machines will have additional covers, but all dimensions will remain
the same.
Air inlet can be provided at drive end at top, bottom, or either side if so specified.
Totally enclosed separately ventilated enclosures can be provided with both air inlet
and outlet at top, bottom, or either side.
 For shipping weight, add 15% to net weight.

Terms

Commutator end shaft extension is furnished only when specifically ordered.
Standard conduit box location is right hand side for motor and left hand side for
generator facing commutator end. Conduit box can be assembled on the opposite
side of frame, or assembled so that entrance can be made from above, from
commutator end, or from drive end if so specified. Fixed termination is provided for
customer connections.

Box

Application
Information

Frame

Approx. Wk2
of Armature
Ft. Lb.

Other

BS

Approx.
Net Wt.
in Lb.

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36C706025AA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.33

Frames 6977 to 6999

Dripproof Fully Guarded, Separately Ventilated
and Enclosed Separately Ventilated

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

BS

Frame

Approx.
Net Wt.
in Lb.

Approx. Wk2
of Armature
Ft. Lb.

B

2F

C

CD6977

23400

5100

64.4

55

95.130

CD6981

26000

6000

68.4

60

CD6985

28700

6350

73.4

CD6986

24300

5250

73.0

CD6990

26900

6200

CD6991

31700

8850

CD6996

29600

CD6999

34400

CONDUIT BOX DIMENSIONS

FC

Standard
Box

Oversize
Box

Frame

110.08

34.81

31.81

CD6977

99.130

114.08

38.81

35.81

CD6981

65

104.13

119.08

43.81

40.81

CD6985

65

103.73

118.68

31.81

28.81

CD6991

77.0

70

107.73

122.68

35.81

32.81

CD6986

79.9

70

110.63

125.58

50.31

47.31

CD6990

6550

82.0

75

112.73

127.68

40.81

37.81

CD6996

9050

88.5

80

119.23

134.18

47.31

44.31

CD6999

Commutator end shaft extension is furnished only when specifically ordered.
Standard conduit box location is right hand side for motor and left hand side for
generator facing commutator end. Conduit box can be assembled on the opposite
side of frame, or assembled so that entrance can be made from above, from
commutator end, or from drive end if so specified. Fixed termination is provided for
customer connections.

Box

AB

AF

XA

Standard

51.75

12

24

Oversize

55.75

15

30

Standard

55.75

15

30

Oversize

61.75

18

36

Splashproof machines will have additional covers, but all dimensions will remain
the same.
Air inlet can be provided at drive end at top, bottom, or either side if so specified.
Totally enclosed separately ventilated enclosures can be provided with both air inlet
and outlet at top, bottom, or either side.
 For shipping weight, add 15% to net weight.

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

From 36C706026AA

4.34

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Blower Unit, without Filters
Frames 6000 to 6900

General
Information

Type CD

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

XG

CD6000

290

54.86

43.25

14.38

4.91

29.44

23.20

4.50

CD6100

419

62.26

48.35

17.23

4.83

35.16

27.79

5.39

CD6200

469

71.31

56.25

17.52

4.97

36.02

30.08

4.71

Frame

Approx. Net Wt. in Lb.

XA

XB

XC

XD

XE

CD6700

706

80.88

63.75

21.40

4.89

41.56

CD6800

732

86.88

69.75

19.92

7.14

44.31

CD6900

770

96.88

79.75

16.90

7.39

44.56

Terms

Other

Application
Information

Outline
Dimensions

Frame

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36B476120AA, 36B476120AB

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.35

Blower Unit, with Filters
Frames 6000 to 6900

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Frame

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

XG

XH

CD6000

398

58.88

43.25

14.79

9.760

54.23

10.16

8.060

4.50

CD6100

525

63.98

48.35

12.79

13.48

60.03

11.70

9.900

5.39

CD6200

573

71.88

56.25

12.79

13.34

60.75

11.70

10.49

4.71

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

Frame

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

XG

CD6700

848

91.82

63.75

21.63

17.98

66.36

11.55

12.81

CD6800

874

97.82

69.75

20.14

15.73

66.86

11.80

14.30

CD6900

912

107.82

79.75

17.13

15.48

66.86

11.80

17.30

From 36B476120BA, 36B476120BB

4.36

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Blower Unit, with Filters

Splashproof Fully Guarded

Frames 6000 to 6900

General
Information

Type CD

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

XG

XH

CD6000

443

55.88

43.25

14.79

9.760

65.43

10.16

8.06

4.50

CD6100

570

63.98

48.35

12.79

13.48

71.23

11.70

9.90

5.39

CD6200

618

71.88

56.25

12.79

13.34

71.95

11.70

10.49

4.71

Frame

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

CD6700

938

91.820

63.75

21.63

17.98

77.56

11.55

964

97.820

69.75

20.14

15.73

78.06

11.80

1002

107.82

79.75

17.13

15.48

78.06

11.80

Terms

CD6800
CD6900

Other

Application
Information

Outline
Dimensions

Frame

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36B476120CA, 36B476120CB

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.37

TEAAC

Totally Enclosed
Air-To-Air Cooled

CD6000 to CD6200

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

FIGUrE 2

FIGUrE 1

Frame

Fig.

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

XG

XH

XJ

XK

XM

XP

CD6000

1

1300

84.50

46.0

16

32

18

36

20.56

70.34

2.16

6.500

7.84

25

CD6100

2

1700

97.60

51.1

18

36

20

40

18.56

77.22

5.91

8.120

5.84

27

CD6200

2

2100

105.5

59.0

18

36

20

40

18.56

81.97

3.90

10.56

5.84

29

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

From 36C706021AJ

4.38

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

TEAAC

Totally Enclosed
Air-To-Air Cooled

CD6700 to CD6900

General
Information

Type CD

Fig.

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

XG

XH

XJ

XK

XM

XP

CD6700

1

2400

114.0

63

23.25

46.5

24.44

48.88

27

89.940

3.06

9.440

5.39

30

CD6800

2

2900

122.5

70

25.50

51.0

26.88

53.75

30

90.030

1.84

11.12

6.03

32

CD6900

2

3900

140.5

80

25.50

51.0

26.88

53.75

30

101.15

1.84

11.12

5.77

32

Terms

Other

Application
Information

Frame

Outline
Dimensions

FIGUrE 2

FIGUrE 1

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36C706024AJ

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.39

TEWAC

Totally Enclosed
Water-To-Air Cooled

CD6000 to CD6200

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Motor Pricing

General
Information

Type CD

FIGUrE 2

Accessories &
Modifications

Modifications
Pricing

FIGUrE 1

FIGUrE 2
CD6200

Frame

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

XG

XH

XJ

XK

XM

XP

Xr

XS

CD6000

1500

65.63

40.13

77.73

19.5

31.63

21.00

27.44

16.75

37.75

1.75

73.70

26.25

15.5

11.1

CD6100

1500

74.98

45.23

87.08

22.5

34.63

25.25

30.44

19.75

29.75

1.75

89.98

27.13

20.9

16.5

CD6200

1800

78.63

53.13

91.24

27.0

39.13

21.50

34.94

24.25

36.25

2.25

92.28

26.88

20.9

16.5

Terms

Other

Application
Information

Outline
Dimensions

FIGUrE 1
CD6000 & CD6100

From 36C706021AK

4.40

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

TEWAC

Totally Enclosed
Water-To-Air Cooled

CD6700 to CD6900

General
Information

Type CD

Approx. Net
Wt. in Lb.

XA

XB

XC

XD

XE

XF

XG

XH

XJ

XK

XM

XP

Xr

XS

XT

CD6700

2200

92.070

58.13

104.16

25.50

37.63

29.43

33.44

22.75

43.75

4.25

93.05

30.63

18.50

13.56

18.0

CD6800

2800

116.13

64.13

128.23

27.00

39.13

47.50

34.84

24.25

45.25

4.25

115.0

36.33

28.00

23.06

18.0

CD6900

3000

116.25

73.75

127.70

31.57

43.57

38.37

39.38

28.75

53.75

6.75

117.8

42.75

23.81

18.86

22.5

Terms

Other

Application
Information

Frame

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36C706024AK

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.41

Dimensions, Air Openings
Frames 6050 to 6066

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Motor Pricing

General
Information

Type CD

Accessories &
Modifications

Modifications
Pricing

FIGUrE 1

FIGUrE 2

Terms

Other

Application
Information

Outline
Dimensions

(SAME AS FIGUrE 1
EXCEPT AS SHOWN)

Frame

Figure

CD6050

1

CD6054

2

CD6052

1

CD6057

2

CD6055

1

CD6059

2

CD6058

1

CD6063

2

CD6062

1

CD6066

2

XA
14.8
16.9
19.5
22.7
26.7

From 36C706070BA

4.42

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Dimensions, Air Openings
Frames 6154 to 6177

General
Information

Type CD

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Accessories &
Modifications

Modifications
Pricing

FIGUrE 1

FIGUrE 2

Application
Information

Outline
Dimensions

(SAME AS FIGUrE 1
EXCEPT AS SHOWN)

1

CD6163

2

CD6157

1

CD6165

2

CD6160

1

CD6168

2

CD6164

1

CD6173

2

CD6169

1

CD6177

2

XA
17.0

Other

Figure

19.6
22.8
26.8

Terms

Frame
CD6154

31.4

From 36C706070BB

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.43

Dimensions, Air Openings
Frames 6259 to 6280

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Modifications
Pricing

Motor Pricing

General
Information

Type CD

Accessories &
Modifications

FIGUrE 1

Outline
Dimensions

FIGUrE 2

Terms

Other

Application
Information

(SAME AS FIGUrE 1
EXCEPT AS SHOWN)

Frame

Figure

CD6259

1

CD6268

2

CD6262

1

CD6270

2

CD6266

1

CD6275

2

CD6271

1

CD6280

2

XA

20.1
23.3
27.3
31.9

From 36C706070BC

4.44

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Dimensions, Air Openings
Frames 6766 to 6785

General
Information

Type CD

Frame

XA

CD6766

27.67

CD6770

31.17

CD6774

35.17

CD6779

40.17

CD6771

27.67

CD6776

31.17

CD6778

35.17

CD6785

40.17

XB

XC

XD

7.50

17.0

25.25

9.65

21.3

29.55

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36C706070AA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.45

Dimensions, Air Openings
Frames 6873 to 6896

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

Frame

XA

CD6873

30.55

CD6876

34.55

CD6881

39.05

CD6887

44.55

CD6882

30.55

CD6885

34.55

CD6890

39.05

CD6896

44.55

XB

XC

XD

6.20

14.4

18.0

10.5

23.0

26.6

From 36C706070AB

4.46

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Dimensions, Air Openings
Frames 6977 to 6999

General
Information

Type CD

Frame

XA

CD6977

33.97

CD6981

37.97

CD6985

42.97

CD6991

49.47

CD6986

33.97

CD6990

37.97

CD6996

42.97

CD6999

49.47

XB

XC

XD

7.20

16.4

19.8

11.5

25.0

28.4

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36C706070AC

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.47

Accessory Mountings
Frames 180AT to 5010AY

For All Motors Except Those
with TEFC Enclosure

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

NOTES:

Other

Accessories shaft as shown furnished on
all machines not having commutator end
shaft extensions.
Accessories shaft is suitable for driving
tachometer and speed limit switch.
Tapped hole is not concentric with shaft
diameters.

Terms

For brake application a keyed commutator
end shaft extension is required.

Standard Commutator End Bracket and Accessory Shaft Extension on CD180AT-CD500AT Machines
(Dimensions do not apply to TEFC machines.)

4.48

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

From 36C697103AA

Accessory Mountings
Frames 6000 to 6900

General
Information

Type CD

Frame
CD6000
CD6100
CD6200

XAO
11.125
11.123
11.125
11.123
14.375
14.372

CD6700

14.375

CD6800

14.372

CD6900

14.375
14.372

XBO

XCO

XDO

XE

XFO

XG

XH

XJO

11.75

11.75

9.875

0.12

3.875

1.00-8

2.38

1.5

11.75

11.75

9.750

0.12

4.500

1.00-8

2.38

1.5

15.00

13.25

11.25

0.12

5.375

1.50-6

3.50

2.0

15.00

16.00

14.00

0.12

6.215

1.50-6

3.50

2.0

15.00

17.50

15.50

0.14

6.215

1.50-6

3.50

2.0

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36C706009AA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.49

Accessory Couplings

Frames 180AT to 500AT and 6000 to 6900

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

“A”
Diameter
0.6255
0.6250

Outline
Dimensions

TORSIONALLY RIGID COUPLING
RATED AT .17 HP
PER 100 RPM

0.7505
0.7500
0.5005
0.5000
0.3130

Depth

0.1875

0.0937

0.1875

0.0937
OMIT
OMIT

Terms

Other

Application
Information

0.3123

Key Way
Width

4.50

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Accessory Adapters

Frames 180AT to 500AT and 6000 to 6900

General
Information

Type CD

BC42/BC46 tachometer adapter
mounts on bracket (See motor outline.)

Terms

Other

Application
Information

Outline
Dimensions

Form "Y" tachometer adapter
mounts on bracket (See motor outline.)

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.51

Speed Limit Device
Frames 180AT to 6900

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
NOTES:
On frames CD180AT through
CD320AT, the speed limit switch
can be mounted with condulet
on right or left side, but will be
mounted on same side as machine
leads unless otherwise specified.
Providing mounting conditions
permit, condulet may be turned so
that entrance can be made in any
direction.

FOr FrAMES
CD180AT - CD500AT
WEIGHT - 14 LB.

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

Frame

AB

AC

P

CD180AT

7.59

6.43

8.86

CD210AT Thru
CD500AT

7.92

6.76

9.73

On frames CD360AT through
CD500AT, the speed limit switch
can be mounted with condulet on
right or left side, or top or bottom,
but will be mounted on same side
as machine leads unless otherwise
specified. Providing mounting
conditions permit, condulet may
be turned so that entrance can be
made in any direction.

From 36A168434AC

Other

Application
Information

FOr FrAMES CD6000-CD6900

Frame
CD6000

Terms

CD6100
CD6200 Thru
CD6900

Approx. Net Wt. in Lbs.

XA

XB

34

13.00

10.00

50

16.25

11.75

Limit switch may be arranged for circuit opening or circuit closing or both.
Limit switch may be mounted on either side, but will be mounted on the same side as machine leads unless otherwise specified.

From 36C695008RA

4.52

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Avtron Tachometer
Frames 180AT to 6900

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction
2.54 [64.5]
3.83 [97.3]

0.24 [6.1]

Ø0.562 [14.3] - 4 HOLES

4.66 [118.4]

LED ALARM
INDICATOR

Motor Pricing

45°

OPTIONAL 2nd ISOLATED OUTPUT

4.38
[111.1]

COVER PLATE
SINGLE OUTPUT ONLY

Ø7.250
[Ø184.15]

0.53 [13.5]

Ø 8.5015
8.5035

Ø 8.500
8.498

215.99 ]
[ Ø 215.94

215.85 ]
[ Ø 215.90

Modifications
Pricing

0.19 [4.8]

OPTION "N"
1/2" FLEXIBLE WATERPROOF
CONDUIT

1/2-14 NPT
OPTIONS "P","V"&"G"
PLUG-IN INDUSTRIAL CONNECTOR

Accessories &
Modifications

5 FT [1524.0] MIN

Ø9.00 [Ø228.6]

1.29
[32.8]
1/8-27 NPT DRAIN PLUG
NOTE: IF THE ENCODER WILL BE EXPOSED
TO WATER SPRAY, THE BOTTOM PIPE PLUG
SHOULD BE REMOVED

Outline
Dimensions

AVTrON AV850 SMArTach II™
WEIGHT — 9 LBS
FOr FrAMES CD180-CD6900

4 - SEE SHEET 2 FOR OTHER AVAILABLE TERMINATIONS
3 - DIMENSIONS ARE IN INCHES [MILLIMETERS]
2 - ALL DIMENSIONS ARE APPROX.
1 - WEIGHT:
NOTES:

DRAWING NUMBER

AV850

3.83 [97.3]

SHEET 1 OF 2

1.23 [31.3]
OPTIONAL
SHAFT GROUND

Application
Information

4.66 [118.4]
8.43 [214.0]

0.13 [3.2]

OPTIONAL 2nd ISOLATED OUTPUT

3/16 [4.763]
SQ. KEY
FURNISHED

COVER PLATE
SINGLE OUTPUT ONLY

5.56 [141.2]

0.53 [13.5]
16°

16°

Other

7.38 [187.3]

Ø4.50 [114.3]
Ø6.75 [171.4]

5 FT [1524.0] MIN
1/2-14 NPT
LED ALARM
INDICATOR
OPTIONS "P","V"&"G"
PLUG-IN INDUSTRIAL CONNECTOR
OPTIONAL
DUAL SHAFT

0.6250/0.6245

45°

45°

3/8-16 UNC x 5/8 DEEP
4 PLACES

Ø [15.875/15.862]

2.06 [52.3]

BOTH ENDS

Terms

1.87 [47.6]

Ø5.875 [Ø149.2]

OPTIONS "M"&"N"
1/2" FLEXIBLE WATERPROOF
CONDUIT

3.35 [85.1]

4 - SEE SHEET 2 FOR OTHER AVAILABLE TERMINATIONS
3 - DIMENSIONS ARE IN INCHES [MILLIMETERS]
2 - ALL DIMENSIONS ARE APPROX.
1 - WEIGHT:
NOTES:

www.gemotors.com

•

800-541-7191

AVTrON AV485 SMArTach II™
WEIGHT — 11 LBS
FOr FrAMES CD180-CD6900

GEP387M 09/11 • Prices and data subject to change without notice.

DRAWING NUMBER

AV485

4.53

Avtron Tachometer
Frames 180AT to 6900

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Motor Pricing

OPTIONS "P" & "G"
PLUG-IN INDUSTRIAL
CONNECTOR

1.97
[50.0]

1/2-14 NPT

LED ALARM
INDICATOR

OPTIONAL COVER
FOR EXTENDED
SHAFT MOTORS

8.54
[216.9]

8.03
[204.0]

8.500
8.498
[215.900]
[215.849]
DIA
4.38
[111.1]

8.5015
8.5035
[215.9381]
[215.9889]
DIA

45°

9.00 DIA
[228.6]

Accessories &
Modifications

Modifications
Pricing

5.38
[136.6]

0.19 [4.8]
4.38 [111.1]

0.24 [6.1]
[30.0]

1.18

8.75 [222.3]
OPTIONAL ISOLATED
DUAL OUTPUT

2.94 [74.7]

0.547 [13.89] DIA
4 HOLES EQUALLY SPACED
ON A 7.250 [184.15] DIA

Outline
Dimensions

STANDARD FLAT COVER
SEE NOTE 4

AVTrON AV85 THIN-LINE II™
WEIGHT — 2.5 - 4 LBS
FOr FrAMES CD180 - CD6900

4 - STANDARD FLAT COVER SHOWN IN FRONT VIEW.
OPTIONAL THRU-SHAFT COVER NOT SHOWN.

DRAWING NUMBER

AV85A
SHEET 1 OF 2

MAGNETORESISTIVE, NEMA 8.500 C-FACE

Application
Information

3.83 [97.3]
HOLE FOR
Ø1.122/1.125 [28.499/28.575]
SHAFT

4.66 [118.4]
8.43 [214.0]

1.26 [32.1]
OPTIONAL
SHAFT GROUND

OPTIONAL 2nd ISOLATED OUTPUT

0.53 [13.5]

7.42 [188.5]

6.75 [171.5]

Other

5.56 [1

41.2]

COVER PLATE
SINGLE OUTPUT ONLY

16°

5 FT [1524.0] MIN

1/2-14 NPT
LED ALARM
INDICATOR

OPTIONAL
THRU
SHAFT
MODEL

OPTIONS "P","V"&"G"
PLUG-IN INDUSTRIAL CONNECTOR
CUSTOMER SHAFT

Terms

16°

Ø5.875 [Ø149.2]
41°

41°

OPTIONS "M"&"N"
1/2" FLEXIBLE WATERPROOF
CONDUIT

3/8-16 UNC x 5/8 DEEP
4 PLACES

3.350 [85.1]
3.38/4.13 [85.7/104.9]
STUB SHAFT EXTENSION
4.720 [119.9]

4.54

4 - SEE SHEET 2 FOR OTHER AVAILABLE TERMINATIONS
3 - DIMENSIONS ARE IN INCHES [MILLIMETERS]
2 - ALL DIMENSIONS ARE APPROX.
1 - WEIGHT:
NOTES:
www.gemotors.com •

AVTrON AV685 SMArTach™ (HOLLOW SHAFT)
WEIGHT — 14 LBS
FOr FrAMES CD180 - CD6900

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Type AN Tachometer
Frames 180AT to 6900

General
Information

Type CD

For frame sizes CD180AT through
CD6900, the tachometer can be
mounted with condulet on right or
left side, top or bottom, but will be
mounted on same side as machine
leads unless otherwise specified.
Providing mounting conditions
permit, condulet may be turned so
that entrance can be made in any
direction.

AN-AC
WEIGHT — 15 LB.

From 36A180215AA
OPTIONAL SECOND
SENSOR MODULE

Outline
Dimensions

4X Ø.625 THRU
ON A Ø7.250 B.C.

3.732

8.08
.400
MAGNETIC WHEEL
POSITION

Ø8.499 ± .001

Ø2.375

-.002
-.003

Ø8.5010

+.0015
+.0005

Application
Information

FLAT
COVER

4.350

4X 3/8-16 X 3/4" LOW
HEAD SOCKET CAP SCREW
8.08
.250

Accessories &
Modifications

NOTES:

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

.200

4X #10-32 X .79L
HEX HEAD SCREW

2.560

Other

#6-32 X 1/2" SHCS
4 PER SENSOR MODULE

2.15
4.47

1/2" NPT
CONDUIT CONNECTION
8.94

DIMENSIONS IN INCHES
Single

Dual
NORTHSTAR RIM Tach RT8

PPr

A

B

C

D

A

B

C

D

240

12.22

7.64

7.11

—

15.28

7.64

7.11

14.21

600

12.78

8.21

7.67

—

16.41

8.21

7.67

15.34

DRAWING NUMBER

702998-0001
19OCT2011

Terms

Output

NOrTHSTAr rIM Tach® rT8
AN-DG
WEIGHT — 15 LB.
From L79202-1

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.55

Northstar Tachometer

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

Application
Information

Outline
Dimensions

NOrTHSTAr rIM Tach® 6200
WEIGHT 27 LB.
FrAME CD180AT-CD6900

Terms

Other

NOrTHSTAr SL85
FrAMES CD180AT-CD500AT

4.56

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Northstar Tachometer
Frames CD180 to CD6900

General
Information

Type CD

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Terms

Other

Application
Information

Outline
Dimensions

NOrTHSTAr rIM Tach® 1250
FOr CD6000 FrAMES ONLY

NOrTHSTAr SLIM Tach® HS56 HOLLOW SHAFT ENCODEr
FOr FrAMES CD180 - CD6900

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.57

Dynapar Encoder
Frames CD180 to CD6900

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

10-32 CLAMP SCREW
TORQUE TO 50 - 55 IN/LBS
WITH LOCTITE ON THREADS

Motor Pricing

General
Information

Type CD

2X
Ø0.6228 +.002/-.000

.86
[21.84]

3.36
[85.34]

3X 10-32 UNC-2B (X) .19 DEEP
ON DIA. 3.000 BOLT CIRCLE

120°
3X

ø

2.50
[63.50]

Modifications
Pricing

2.25
[57.15]

.06
[1.52]
1.95
[49.53]

1.25
ø[31.75]

.57
[14.48]

ø 2.50
[63.45] PILOT

SHOWN WITH 10 PIN CONNECTOR

ø 3.80
[96.52]

Accessories &
Modifications

FOR REFERENCE

DYNAPAr HA625 ENCODEr
FOr FrAMES CD180 - CD6900

DYNAPAr HS35r ENCODEr
HOLLOW SHAFT — WEIGHT 16 OZ
Dynapar
Encoder
FOr FrAMES
CD180HS35R
- CD6900

Outline
Dimensions

DWG. NO.

702990-0001
09-27-11

Terms

Other

Application
Information

DATE

DYNAPAr X25 ENCODEr
EXPLOSIONPrOOF
WEIGHT — 4.5 LBS
FOr FrAMES CD180 - CD6900

4.58

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

3.000
[76.20]

Dynapar rotopulse
Frames 180AT to 6900

General
Information

Type CD

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Terms

Other

Application
Information

DYNAPAr H56 rOTOPULSEr
WEIGHT — 9 LBS
FOr FrAMES CD180 - CD6900

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.59

eXcellon® Type BC Tachometer
Frames 180AT to 6900

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

From 36A180215AB

Terms

Other

Application
Information

Outline
Dimensions

FOr FrAMES CD180AT-CD6900
BC42
WEIGHT — 35 LB.

FOr FrAMES CD180AT-CD6900
BC46
WEIGHT — 45 LB.

4.60

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

From 36A180215AC

eXcellon® Form Y Tachometer
Frames 180AT to 6900

General
Information

Type CD

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Type

XA

XB

5PY59EY

5.06

9.02

5PY59JY

6.50

10.46

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

Model 5PY59EY is an AC tachometer generator for speed-indicating duty.
Model 5PY59JY is a DC tachometer generator for speed-regulating and/or speed-indicating duty.

Terms

Other

FOr FrAMES CD180AT-CD6900
FOrM Y
WEIGHT — 25 LB.

From 36A180215AD

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.61

Sliding Base

Horizontal Floor Mounting Only

Frames 180AT to 500AT

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

Approx.
Net Wt.
in Lbs.

BB

E

F

AL

AM

AO

Ar

AT

AU

AX

BT

XH

XC

CD182AT

9.00

6.500

3.75

2.25

12.75

9.5000

4.50

4.250

0.1340

0.500

1.50

3.00

0.375 X 1.50

1.2500

CD186AT

11.0

9.000

3.75

3.50

12.75

12.000

4.50

5.500

0.1340

0.500

1.50

3.00

0.375 X 1.50

1.2500

CD189AT

14.0

12.00

3.75

5.00

12.75

15.000

4.50

7.000

0.1340

0.500

1.50

3.00

0.375 X 1.50

1.2500

CD218AT

17.0

12.00

4.25

5.00

15.00

15.500

5.25

7.000

0.1640

0.500

1.75

3.50

0.375 X 1.50

1.2500

CD219AT

21.5

13.00

4.25

5.50

15.00

16.500

5.25

7.500

0.1640

0.500

1.75

3.50

0.375 X 1.50

1.2500

CD2110AT

19.0

14.50

4.25

6.25

15.00

18.000

5.25

8.250

0.1640

0.500

1.75

3.50

0.375 X 1.50

1.2500

CD258AT

20.0

15.00

5.00

6.25

17.75

19.375

6.25

8.750

0.1875

0.625

2.00

4.00

0.500 X 1.75

1.4375

CD259AT

21.0

16.50

5.00

7.00

17.75

20.875

6.25

9.500

0.1875

0.625

2.00

4.00

0.500 X 1.75

1.4375

CD287AT

24.0

15.50

5.00

6.25

19.75

19.875

7.00

9.000

0.1875

0.625

2.00

4.50

0.500 X 2.00

1.6875

CD288AT

24.0

17.00

5.50

7.00

19.75

21.375

7.00

9.750

0.1875

0.625

2.00

4.50

0.500 X 2.00

1.6875

CD327AT

34.0

17.50

6.25

7.00

22.75

22.750

8.00

10.25

0.1875

0.750

2.50

5.25

0.625 X 2.50

2.1875

CD328AT

35.0

19.50

6.25

8.00

22.75

24.750

8.00

11.25

0.1875

0.750

2.50

5.25

0.625 X 2.50

2.1875

CD329AT

36.0

21.50

6.25

9.00

22.75

26.750

8.00

12.25

0.1875

0.750

2.50

5.25

0.625 X 2.50

2.1875

CD365AT*

45.0

16.50

7.00

6.12

25.50

21.500

9.00

9.620

0.2500

0.880

2.50

6.00

0.750 X 3.00

2.5000

CD366AT*

50.0

18.25

7.00

7.00

25.50

23.250

9.00

10.50

0.2500

0.880

2.50

6.00

0.750 X 3.00

2.5000

CD368AT*

60.0

22.25

7.00

9.00

25.50

27.250

9.00

12.50

0.2500

0.880

2.50

6.00

0.750 X 3.00

2.5000

CD407AT*

64.0

22.25

8.00

9.00

28.75

28.125

10.0

12.75

0.2500

1.000

3.00

7.00

0.875 X 3.50

3.0000

CD409AT*

70.0

26.25

8.00

11.0

28.75

32.125

10.0

14.75

0.2500

1.000

3.00

7.00

0.875 X 3.50

3.0000

CD504AT*

132

20.75

10.0

8.00

35.00

28.000

12.5

12.50

0.3125

1.250

3.50

8.00

1.125 X 3.50

3.0000

CD506AT*

138

24.75

10.0

10.0

35.00

32.000

12.5

14.50

0.3125

1.250

3.50

8.00

1.125 X 3.50

3.0000

CD508AT*

146

29.75

10.0

12.5

35.00

37.000

12.5

17.00

0.3125

1.250

3.50

8.00

1.125 X 3.50

3.0000

Other

Application
Information

Outline
Dimensions

Frame

DIMENSIONS IN INCHES

Terms

*These frames have two adjusting screws and eight gussets shown in phantom.

From 533C230AC

4.62

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Soleplates

Frames CD210AT to CD500AT

General
Information

Type CD

C

D

E

F

G

H

J

K

L

M

CD218AT

1.62

13.25

OMIT

15.00

3

0.88

8.50

11.5

0.56

0.88

6.230

1.5

CD219AT

1.62

14.25

OMIT

16.00

3

0.88

8.50

11.5

0.56

0.88

6.230

1.5

CD2110AT

1.62

15.75

OMIT

17.50

3

0.88

8.50

11.5

0.56

0.88

6.230

1.5

CD258AT

2.00

16.50

OMIT

18.50

4

1.12

10.0

14.0

0.69

1.00

7.470

2.0

CD259AT

2.00

18.00

OMIT

20.00

4

1.12

10.0

14.0

0.69

1.00

7.470

2.0

CD287AT

2.00

16.50

OMIT

18.50

4

1.12

11.0

15.0

0.69

1.00

8.220

2.0

CD288AT

2.00

18.00

OMIT

20.00

4

1.12

11.0

15.0

0.69

1.00

8.220

2.0

CD327AT

2.25

18.50

OMIT

21.00

4

1.38

12.5

16.5

0.81

1.25

9.480

2.0

CD328AT

2.25

20.50

OMIT

23.00

4

1.38

12.5

16.5

0.81

1.25

9.480

2.0

CD329AT

2.25

22.50

OMIT

25.00

4

1.38

12.5

16.5

0.81

1.25

9.480

2.0

CD365AT

2.25

16.75

OMIT

19.75

5

1.38

14.0

19.0

1.00

1.50

10.48

2.5

CD366AT

2.25

18.50

OMIT

21.50

5

1.38

14.0

19.0

1.00

1.50

10.48

2.5

CD368AT

2.25

22.50

7

25.50

5

1.38

14.0

19.0

1.00

1.50

10.48

2.5

CD3610AT

2.25

26.50

7

29.50

5

1.38

14.0

19.0

1.00

1.50

10.48

2.5

CD2612AT

2.25

32.50

7

35.50

5

1.38

14.0

19.0

1.00

1.50

10.48

2.5

CD407AT

2.75

23.50

8

26.75

6

1.88

16.0

22.0

1.12

1.62

11.98

3.0

CD409AT

2.75

27.50

8

30.75

6

1.88

16.0

22.0

1.12

1.62

11.98

3.0

CD4012AT

2.75

37.50

8

40.75

6

1.88

16.0

22.0

1.12

1.62

11.98

3.0

CD504AT

3.25

22.50

8

26.50

6

1.88

20.0

26.0

1.38

2.00

14.48

3.0

CD506AT

3.25

26.50

9

30.50

6

1.88

20.0

26.0

1.38

2.00

14.48

3.0

CD508AT

3.25

31.50

9

35.50

6

1.88

20.0

26.0

1.38

2.00

14.48

3.0

CD5010AY

3.25

38.50

9

42.50

6

1.88

20.0

26.0

1.38

2.00

14.48

3.0

Terms

NOTE: Motors are shipped with sole plates bolted to motor feet. Shims are included. Motor and sole plates will be installed as a unit.
Sole plates will not be removed from motor and installed separately.

Outline
Dimensions

B

Application
Information

A

Other

DIMENSIONS IN INCHES
Frame

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

From 36A167263CA

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.63

Soleplates

Frames CD6050 to CD6280

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Frame

Approx. Net
Wt. in Lbs.

XA

XB

XC

XD

XE

XF

XG

CD6050

412

48.0

52.0

7

2.00

30

35

16.62
16.62

CD6052

428

50.0

54.0

7

2.00

30

35

CD6054, 6055

444

52.0

56.0

7

2.00

30

35

16.62

CD6057

460

54.0

58.0

7

2.00

30

35

16.62

CD6058, 6059

476

56.0

60.0

7

2.00

30

35

16.62

CD6062. 6063

508

60.0

64.0

7

2.00

30

35

16.62

CD6066

539

64.0

68.0

7

2.00

30

35

16.62
19.12

CD6154

444

52.0

56.0

7

2.00

35

40

CD6157

460

54.0

58.0

7

2.00

35

40

19.12

CD6160

476

58.0

62.0

7

2.00

35

40

19.12

CD6163

508

60.0

64.0

7

2.00

35

40

19.12

CD6164

523

62.0

66.0

7

2.00

35

40

19.12
19.12

CD6165

539

64.0

68.0

7

2.00

35

40

CD6168, 6169

555

66.0

70.0

7

2.00

35

40

19.12

CD6173

587

70.0

74.0

7

2.00

35

40

19.12

CD6177

626

75.0

79.0

7

2.00

35

40

19.12

CD6259

617

56.5

60.5

8

2.25

42

47

23.37

CD6262

647

59.5

63.5

8

2.25

42

47

23.37

CD6266, 6268

703

65.0

69.0

8

2.25

42

47

23.37

CD6270, 6271

739

68.5

72.5

8

2.25

42

47

23.37

CD6275

780

72.5

76.5

8

2.25

42

47

23.37

CD6280

831

77.5

81.5

8

2.25

42

47

23.37

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

4.64

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Soleplates

Frames CD6766 to CD6999

General
Information

Type CD

XC

XD

XE

XF

XG

XH

XJ

XK

64.60

68.620

7.500

32.9

42.46

45.46

27.12

21.7

4.50

7.75

CD6770

876.0

68.10

72.120

7.500

36.4

42.46

45.46

27.12

21.7

4.50

7.75

CD6771

886.0

66.90

72.940

7.500

32.9

42.46

45.46

27.12

21.7

4.50

7.75

CD6774

924.0

72.10

76.120

7.500

40.4

42.46

45.46

27.12

21.7

4.50

7.75

CD6776

926.0

72.40

76.440

7.500

36.4

42.46

45.46

27.12

21.7

4.50

7.75

CD6778

974.0

76.40

80.440

7.500

40.4

42.46

45.46

27.12

21.7

4.50

7.75

CD6779

982.0

77.10

81.120

7.500

45.4

42.46

45.46

27.12

21.7

4.50

7.75

CD6785

1034

81.40

85.440

7.500

45.4

42.46

45.46

27.12

21.7

4.50

7.75

CD6873

1466

71.22

75.250

12.00

42.5

54.20

57.20

30.12

27.0

9.00

8.30

CD6876

1542

75.22

79.250

12.00

46.5

54.20

57.20

30.12

27.0

9.00

8.30

CD6881

1628

79.72

83.750

12.00

51.0

54.20

57.20

30.12

27.0

9.00

8.30

CD6882

1630

79.82

83.810

12.00

42.5

54.20

57.20

30.12

27.0

9.00

8.30

CD6885

1706

83.82

87.810

12.00

46.5

54.20

57.20

30.12

27.0

9.00

8.30

CD6887

1732

85.22

89.250

12.00

56.5

54.20

57.20

30.12

27.0

9.00

8.30

CD6890

1792

88.32

92.310

12.00

51.0

54.20

57.20

30.12

27.0

9.00

8.30

CD6896

1896

93.82

97.810

12.00

56.5

54.20

57.20

30.12

27.0

9.00

8.30

CD6977

1594

76.60

80.620

12.25

44.2

54.20

68.98

35.12

27.5

9.25

8.25

CD6981

1672

80.60

84.620

12.25

48.2

65.98

68.98

35.12

27.5

9.25

8.25

CD6985

1768

85.60

89.620

12.25

53.2

65.98

68.98

35.12

27.5

9.25

8.25

CD6986

1760

85.20

89.180

12.25

44.2

65.98

68.98

35.12

27.5

9.25

8.25

CD6990

1836

89.20

93.180

12.25

48.2

65.98

68.98

35.12

27.5

9.25

8.25

CD6991

1894

92.10

96.120

12.25

59.7

65.98

68.98

35.12

27.5

9.25

8.25

CD6996

1934

94.20

98.180

12.25

53.2

65.98

68.98

35.12

27.5

9.25

8.25

CD6999

2060

100.7

104.68

12.25

59.7

65.98

68.98

35.12

27.5

9.25

8.25

Outline
Dimensions

XB

834.0

Application
Information

XA

CD6766

Other

Approx. Net
Wt. in Lbs.

Terms

Frame

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

4.65

NEMA Mounting Configurations

DIMENSIONS - For ESTIMATING ONLY unless endorsed for construction

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Type CD

4.66

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Application Information

Page
Air Flow Requirements for Separately Ventilated Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.13

General
Information

Index

Bearing Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5
Bearing Life Factor vs. Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6
Bearing Life (L10) Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.8
Bearing Life Speed vs. Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.7
Blower Data for Blower Ventilated Motors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.14
Blower Data for TEAAC and TEWAC Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.15
Direction of Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5
Environmental Effect on Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5
Environmental Effects on Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4
Maximum Momentary Overload. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2
Motor Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2
Motor Load Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.16

Modifications
Pricing

Audio Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.10

Accessories &
Modifications

Armature Current, Rate of Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2

Outline
Dimensions

Ambient Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5

Motor Pricing

Air Supply Quality Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4

Pinion Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.10
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2
Special Load Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6

Application
Information

Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5

Speed Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2
Standard Constant Torque Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3

Other

Speed Range by Armature Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5

Standard Field Voltages and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2

Thrust Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6
V-Belt Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

5.1

Terms

Starting Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2

Application Information
General
Information

CD180AT-CD6900 Frames

General Information

Safety

All motors are furnished with reconnectable fields as listed in
the tabulation below:

The material in this publication should be used with due
regard to the hazards to personnel resulting from the use
and application of electric motors and generators.

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

STAnDArD FIelD VOlTAGeS AnD COnneCTIOnS
Field Voltage
reconnectable

Field Voltage
When Connected
1 Circuit (Series)

Field Voltage
When Connected
2 Circuit (Parallel)

500 or 240

300/150
240/120

300
240

150
120

180

200/100

200

100

Armature Voltage

Speed Vibration
•	 ±7.5%	at	rated	armature	voltage	and	field	current
•	 Not	to	exceed	15%	full	load	(cold)	to	full	load	(hot)	—	
ventilated
•	 Not	to	exceed	20%	full	load	(cold)	to	full	load	(hot)	—	
totally enclosed

It is strongly recommended that the user become familiar
with the NEMA publication MG2, “Safety Standard for
Construction and Guide for the Selection, Installation, and
Use of Electric Motors and Generators.”
electrical Shocks
Higher direct current motor voltages are now common due
to the use of rectified AC power supplies, and the danger of
shock	is	substantially	increased.	Rectified	460	(RMS)	AC	volt	
power results in about 500 or more volts DC. Overall safety
can be improved by:

Miscellaneous
•	 Torque	= HP x 5252
Base Speed
•	 Air	Rise	=		Air	exhaust	temperature	minus	air	intake	
temperature in degrees C (25 degrees C is
considered high)

1. Specifying that frames of rotating machines be solidly
grounded in accordance with the National Electrical
Starting Current
Code and consistent with sound local practices.
Standard	motors	permit	250%	full	load	current	for	momenBecause paint insulates, foot or flange bolts cannot be
tary	starting	duty	on	frames	CDL182AT-CD5010AY	and	300%	
counted on to provide a satisfactory ground. Standard
on frames CD6000-CD6900.
motors are provided with a brass screw and symbol
inside or adjacent to the conduit box.

Application
Information

Maximum Momentary Overload

Standard continuously rated motors rated 3/4 HP per RPM
and	less	will	carry	150%	full	load	current	for	a	period	of	one	
minute throughout the rated speed range and are suitable
for	higher	current	peaks	below	rated	top	speed.	(Refer	to	
page __ of this publication.)

Other

Motor Fields

Terms

Personnel Protection
Consideration should be given to the type of personnel who
would normally come in close contact with motors and
generators. Equipment installed in locations open to the general
public should be better protected than those located in areas
available only to qualified personnel, who should recognize any
potential hazard involved in the use of the equipment.

Standard motors in frames CDL182AT-CD5010AY and all
ratings in the CD6000-CD6900 frames are shunt wound.

rate of Change of Armature Current
Motors in frames CD6000-CD6200 are suitable for a rate of
change of armature current of 11 per unit per second.
Motors in frames CD6700-CD6900 are suitable for 22 per
unit per second change in armature current. Contact GE for
information if higher rates are needed.

5.2

www.gemotors.com

•

800-541-7191

2. Specifying a dripproof fully guarded enclosure as a
minimum. This will decrease the danger to personnel
from contact with the brush rigging and commutator.
3. Specifying manual reset for overcurrent and
overtemperature protection. Automatic reset allows
resetting at an unsafe time.
4. Specifying circuitry as far as possible, which prevents
access to live motor parts, unless power is removed from
the armature and main field. For silicon-controlled rectified
drives, the AC lines into the rectifier should be opened
	 before	maintenance	work	is	performed	on	the	motor.	
Mechanical Protection
Mechanical hazards to personnel occur due to overspeed,
exposure to rotating parts, mechanical overloading of shafts
or bearings, and failure of lifting devices. GE motors are
designed so that, in an emergency, they will withstand an
overspeed in accordance with the table on the following page:

GEP387M 09/11 • Prices and data subject to change without notice.

Application Information

All DC motors may be subject to potentially dangerous
overspeeding under certain conditions of misoperation.
Overspeeding of a DC compound wound or shunt wound
motor may occur if the shunt field circuit becomes
de-energized.

Care should be exercised in the selection of couplings, belts,
or	pinions	with	due	consideration	given	to	shock	loads,	
overloads, and pulley pitch diameters. See page 5.7 for
bearing life and allowable shaft loading. Too small a pulley
diameter will require excessive belt tension to prevent belt
slippage. This, in turn, overloads the bearings and shafts
which may result in bearing and/or shaft failure, and
possible overspeeding of the motor.

Motor enclosure

Standard Constant Torque

Self-Ventilated

60%	of	base	speed

Blower Ventilated

5%

Additional coverage of the hazards in handling the rotating
equipment covered in this publication may be found in the
instruction	books	sent	out	with	the	equipment.	

Separately Ventilated

5%

Hazards Due To environment
Motors which operate in explosive atmospheres must meet
the requirements of Articles 501-8 or 502-8 of the National
Electrical Code. The Code assigns authority to approve the
installation to “the authority having jurisdiction” (see Article
100	—	Definitions	of	the	NEC).

TEWAC

5%

www.gemotors.com

•

800-541-7191

60%

TEAO

40%

TEAAC

5%

Motors ventilated from a separate source are supplied with a
constant flow of cooling air, which is independent of the
motor operating speed. A constant supply of cooling air
permits much lower speed operation of a separately
ventilated motor at rated torque without exceeding a
maximum allowable temperature rise.

Other

5%

TEFC

Continued operation at high temperature will significantly
reduce insulation life. However, generally most applications
have compensating periods of operation at some
temperature lower than normal so that the use of the
higher current for many applications is justified.

Terms

Motors approved by U.L. for Class I, Group D or Class II,
Groups E, F, and G are available in some ratings. However, it
is the responsibility of the customer to be familiar with the
NEC and the local jurisdictional requirements and to determine that the motor selection (including possibly permissible
alternatives to U.L. approved motors) is “acceptable to the
authority having jurisdiction.”

TENV

Motor Pricing

At low operating speeds, the flow of ventilating air passing
through the machine is reduced resulting in a decreased
heat dissipation rate. Consequently, it becomes necessary to
analyze the motor thermal capacities at each speed and
load condition. In general, motors of dripproof fully guarded,
self-ventilated, and totally enclosed fan cooled enclosures
must	be	operated	above	60%	of	the	motor	base	speed	to	
ensure proper cooling.

Not greater than 50 percent above full load
base speed.

Modifications
Pricing

Specifications should require that guards be placed over
exposed couplings, pulleys, pinions, and unused shaft
extensions for the protection of the operating personnel.

Compound with speed regulation
of 35 percent or less

Accessories &
Modifications

Motor Heating
Cooling air for dripproof fully guarded self-ventilated, and
totally enclosed fan cooled direct current motors is provided
by shaft-driven fans.

Shunt

Outline
Dimensions

Motors can overspeed due to improper wiring during
installation.	GE	installation	and	instruction	books	contain	
statements and instructions to guard against such overspeed due to wrong initial connections.

Maximum Monetary Overspeed
25 percent above the maximum nameplate
speed or 15 percent above the corresponding
no-load speed, whichever is greater.

Application
Information

Unless the speed is inherently limited by the application
of the motor, DC motors should be protected against
dangerous overspeed by overspeed devices, field loss relays,
or other means.

Insulation
Insulation life is dependent on many factors. Insulation
failure results from either chemical or mechanical
degradation or a combination of both. Chemical degradation
is a function of the time and temperature at which the
insulation is operated relative to its temperature rating.
Roughly, a machine operated at the nominal temperature
rating will operate twice as long as a machine operated 10°C
higher. Chemical degradation can also be accelerated, if the
machine operates in dirty or chemical atmospheres or in
atmospheres of high moisture content. Mechanical
degradation occurs when the conductors are subject to high
forces. These forces may cause coil movement, which
eventually can abrade the turn insulation on the wire or
break	the	ground	insulation.

Type of Motor

General
Information

CD180AT-CD6900 Frames

GEP387M 09/11 • Prices and data subject to change without notice.

5.3

Application Information

The exciting fields on all continuously rated, dripproof fully
guarded blower ventilated and separately ventilated, and
totally enclosed nonventilated motors are designed for
continuous	excitation	at	field	voltages	up	to	105%	of	the	
rated value while the motor is operating at any speed and
load within the capability of the armature. Temperatures
under these conditions will not exceed maximum allowable.
However, insulation life will be shortened, particularly during
prolonged operation at low speed.
CAUTIOn:
Motor	Field	Heating	—	Unless	specifically	ordered,	
motors are NOT capable of continuous standstill
excitation at rated field current. When the motor is
shut down for more than 15 minutes, one of the
following options must be used:

Modifications
Pricing

Motor Pricing

General
Information

CD180AT-CD6900 Frames

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

1. De-energize the field completely
2. Use field economy relays to limit the field current to a
maximum	of	50%	of	the	nameplate	rating
3. When applicable, fields may remain fully energized
if the motor ventilation system (blower or customer
duct) remains in operation.

environmental effects On Insulation
The insulation system used on GE DC motors is adequate for
use	in	humid	atmospheres.	Acids,	alkalies,	abrasive	dust,	
conducting dust, etc., when present, impose a severe
hardship on the insulation system. Special consideration is
required to determine the acceptability of a dripproof fully
guarded enclosure, since the contamination itself may
conduct shorting or grounding current over the insulation.
This current gradually develops a permanent creepage path
which can cause failure. The exposed uninsulated circuits on
DC machines, such as the commutator brush rigging and
bolted connections, allow early electrical failure when the
enclosure is inadequate, regardless of the insulation system.
Extra varnish dips will not correct this problem. An adequate
enclosure should be used.
Where contamination is expected, a study of the history of
the application should be made to determine what degree of
protection has been successful in the past. A standard
dripproof fully guarded machine can often be applied
successfully, but a totally enclosed machine will provide
extra reliability.

5.4

www.gemotors.com

•

800-541-7191

Air Supply Quality Guidelines
Cooling air quality can have an effect on machine
performance. Nonconducting contaminants such as cement
dust, dirt, sand, and sawdust can promote overtemperature
by restricting cooling passages and air circulation. Abrasive
materials may erode insulations within the machine.
Conductive contaminants such as carbon dust, metal
particles, and salt can also provide shorting paths to ground.
Periodic “blowing out” or vacuuming of dust accumulation
will tend to avoid major problems if oil, grease, or other
liquids are allowed to enter the machine, contaminants
will	“stick”	to	insulating	surfaces	and	make	effective	
cleaning difficult.
Corrosive gases in applications such as papermills can have
an extreme effect on machine performance and service life.
Chlorine, hydrogen sulfide, and sulphur dioxide can damage
commutator copper, hardware, and varnish systems. On the
commutator, severe contamination will cause unprotected
copper (where the brushes don’t contact) to oxidize and turn
bluish-gray developing scale that can bridge across
insulating mica and cause commutation distress and
possibly a flashover. Contamination produces high friction
and	uneven	film	which	reduces	brush	life.	Sparking	may	
result from poor, uneven, or non-conductive commutator
film which can lead to bar etching and further commutator
surface erosion.
If high corrosion is suspect, air sampling coupons can be
placed in the cooling air to determine corrosion rates. Field
experience has shown that corrosion rates of motor cooling
air should be below .5 microns/year to limit corrosion
damage effects. Air sampling coupons and analysis are
commercially available. Periodic seater stone application
can prevent buildup and uneven commutator filming.
With high corrosion evident, further analysis can pinpoint
the type of gases present. Elimination of high levels of gas
can be made by relocating air inlets to other rooms or areas
or simply raising an inlet off of a wet floor or away from open
gutter-type drains. Additional filtering means such as
charcoal filters can further improve air quality.
effects of radiation
Radiation can cause insulation degradation, if present in
sufficient amounts. Where motors are exposed to the more
common types of atomic radiation, nearly all standard
insulations may be used if the radiation is below 107
Roentgens. Where radiation exceeds this value, specific
information should be included in the requisition,
proposition, or specifications.

GEP387M 09/11 • Prices and data subject to change without notice.

Application Information

Bearing life

Direction of rotation
Motors in frame sizes CDL182AT-CD5010AY are suitable for
continuous rotation in either direction or for reversing duty.
Motors in frame sizes CD6000-CD6900 are suitable for
continuous operation in the rotation specified on the
nameplate for reversing duty. Motors in all frame sizes are
generally suitable for continuous rotation in either direction
or for reversing duty. In frame sizes CD6000-CD6900
applications in contaminated environments require that
brushes be trailing for the desired rotation. If not, they may
experience rapid brush wear during continuous operation
with the brushes stubbing.

Performance
Kinamatic motors meet NEMA standards for industrial
equipment.
regulation	—	See	NEMA	Standards.

Bearing life for belted drives is determined by calculating the
radial load at the end of the shaft.
The radial load, W, produced by the belts when tightened just
enough to transmit the load without slipping is given by the
relation:

(

HP
) ( RPM
) (K , lbs)

W	=	 126,000
D

b

Where:
D	 =		 	Sheave	pitch	diameter	in	inches	for	
V-belt application.
HP = Maximum ratio of horsepower, including overloads,
RPM to the minimum speed at which that power occurs.
Kb		 =		Belt	tension	factor	from	table	below:
BelT TenSIOn FACTOr, Kb
Kb

Description

1.0

Chain	and	Sprocket	Drive

1.2

Timing Belt

1.5

V-Belt, 1:1 Ratio

1.8

V-Belt, 2:1 Speed Decreased Ratio

2.0

Flat Belts

Other

Standard Kinamatic™ dripproof fully guarded and totally
enclosed motors are designed for operation in a 40°C
ambient temperature and at altitudes up to 3,300 feet
above sea level.

excitation	—	See	modification	pages	or	notes	on	price	pages	
The curves which follow can be used to determine the L10
for standard shunt field voltages.
life,	which	is	the	life	in	hours	that	90%	of	bearings	with	this	
Parallel Operation —	Where	motors	are	to	be	operated	in	
load would be expected to exceed without failure. The
electrical and mechanical parallel, refer to GE.
standard ball bearing and standard shaft option will be the
most economical, if acceptable life is obtained from the
curve. A commonly used design figure is 20,000 hours.

www.gemotors.com

•

800-541-7191

Motor Pricing

Ambient Conditions

Modifications
Pricing

The standard NEMA shaft extension is designed for belted
loads. Dimensions are provided on the standard dimension
sheets. A sliding base is available as an accessory to
facilitate belt adjustment.

Accessories &
Modifications

Standard motors are suitable for reduced speed operation
by adjustable armature voltage. Some torque derating may
be necessary for applications requiring extended periods of
low-speed operation. For specific duty cycles contact GE.

WArnInG:
The presence of silicone in DC Motors, particularly totally
enclosed constructions, will cause rapid brush wear.
Sources of silicone include oils, RTV compounds, mold
release agents, and some insulating varnishes. These
silicone substances must be avoided to ensure proper
DC motor performance.

Outline
Dimensions

Speed range By Armature Control

The V-belt system produces a heavy shaft and bearing
loading,	making	it	necessary	that	these	factors	be	
considered carefully for proper application. Since belt drives
impose a bending moment on the motor shaft, it is always
desirable to have the motor sheave located as close to the
motor bearing as possible to minimize both bearing load and
shaft stress. This will result in increased bearing life. The
bearing life curves that follow assume the load is centered at
the end of the shaft. Improved V-belts can significantly
reduce the number and size of belts required for a given
load. These new belts should always be considered, since
the sheave will be shorter and the load centered closer to
the bearing.

Brush Wear Caused by Silicone

Application
Information

V-Belt Drives

GEP387M 09/11 • Prices and data subject to change without notice.

5.5

Terms

environmental effects On Brushes

General
Information

CD180AT-CD6900 Frames

Application Information

Belt	tension	should	be	checked	and	adjusted	following	the	
belt manufacturer’s recommendations.

3.0

2.0
1.5

1.0
.9
.8
.7
.6
.5
.4

Mounting may be either horizontal or vertical for these
bearing life determinations as long as no axial load other
than the weight of the armature is present if vertical.

Terms

Other

Special load Considerations
Where the load is overhung beyond the motor shaft
extension or greater life is desired, the application should be
referred to GE.

Pinion Drives
While Kinamatic motors are not designed for overhung pinion
drives, they may be successfully applied under suitable
conditions. In addition to a radial load, some gears produce
thrust load on the bearing. Vibrations, particularly of the
torsional variety, are limiting on some spur or straight bevel
gear applications. Complete details of the proposed gearing
should be referred to GE in all cases.

5.6

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

5000

Matched	belts	run	smoother,	look	better,	and	last	longer.	
Longer	belt	life	results	if	the	belts	and	sheaves	are	kept	clean	
and the belts are prevented from rubbing against the belt
guards or other obstructions.

4000

AVERAGE RPM

3000

2000

1000

There is normally a drop in tension during the first 24 to 48
hours of operation. During this “run in” period, the belts seat
themselves in the sheave grooves and initial stretch is
removed.	Belt	tension	should	be	re-checked	after	a	day	or	
two of operation.

Bearing life Factor vs. Speed

L10 LIFE FACTOR

If slippage occurs after the belt tension has been correctly
adjusted, the belts and pulleys have not been chosen
properly for the job.

Due to the mounting position or type of drive arrangement,
a thrust load may be applied to the motor shaft. The
Kinamatic motor is designed to permit a limited amount of
thrust load. This permissible load will vary by mounting
position and direction of the load due to the weight of the
armature.

700

Outline
Dimensions

It	is	important	to	know	that	bearing	life	for	V-belt	
applications is independent of the motor load. Once the belts
have been tightened just enough to prevent slipping when
the maximum torque is being delivered by the motor, the
radial load, W, on the shaft and bearing is there and remains
constant regardless of the motor load. For timing belts and
chain drives, the radial load, W, does vary somewhat with
motor load and so the motor load duty cycle, as well as the
average speed should be considered to estimate bearing life.

Thrust loads

500

Application
Information

However, applications with a calculated life of as low as
5,000 hours have sometimes been necessary to limit belt
speeds to 6,000 feet per minute. The curves are drawn for
1750 RPM average speed. If the application has some other
average speed, the life can be adjusted by multiplying by the
bearing life factor curve. (See curve on right)

300

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

CD180AT-CD6900 Frames

General
Information

Application Information

BeArInG lIFe AT 1150 rPM AVerAGe SPeeD VS. lOAD, W
1150
(For other Average Speeds, multiply life by AVG.
SPD. )
Frame Sizes CD6000-CD6200

6000

5600

5000

5300

6200 ROLLER
6100 ROLLER

4000

2000

Modifications
Pricing

6100, 6200 ROLLER
6000 ROLLER

3000

1800

1500

1500

1700

1000

Accessories &
Modifications

6100 BALL
6000 BALL

800

6200 BALL

600

Outline
Dimensions

400

200

Application
Information

100000

10000

1000

BEARING LIFE AT 1150 RPM AVERAGE SPEED Vs. LOAD, W
1150
(For other average speeds, multiply Life by avg
spd )
Frame Sizes CD6000 - CD6200

Other

100

Terms

MAXIMUM RADIAL LOAD, W., AT END OF SHAFT (LBS.)

7500

Motor Pricing

10000

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

5.7

General
Information

Application Information

BeArInG lIFe AT 1750 rPM AVerAGe SPeeD VS. lOAD, W
1750
(For other Average Speeds, multiply life by life AVG.
SPD. )
10000

MAXIMUM RADIAL LOAD, W., AT END OF SHAFT (LBS.)

5000
4000
3000

2630

2000

1670

1500

1340
1000

1000
900
800
700

FRAME
CD500AT

750
550

600

CD400AT
CD360AT

500
400

390

300

280

CD320AT
CD287AT, CD288AT
CD258AT, CD259AT
CD210AT

200

CD180AT

10000

MAXIMUM RADIAL LOAD, W., AT END OF SHAFT (LBS.)

OVerSIze BAll BeArInG AnD OVerSIze SHAFT
5000

5000
4000

3500

3000

2000

2000

1670

1500

1340

FRAME
CD5010AY

1000
900
800
700

CD500AT
CD400AT

600

CD360AT
CD320AT

500
400
300

200

www.gemotors.com

•

800-541-7191

100000
90000
80000
70000
60000

5.8

50000

L10 BEARING LIFE (HOURS)

40000

30000

20000

10000
9000
8000
7000

6000

5000

4000

3000

2000

100

1000

Terms

Other

Application
Information

Outline
Dimensions

L10 BEARING LIFE (HOURS)

100000
90000
80000
70000
60000

50000

40000

30000

20000

10000
9000
8000
7000

6000

5000

4000

3000

2000

100

1000

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

STAnDArD BAll BeArInG AnD STAnDArD SHAFT

GEP387M 09/11 • Prices and data subject to change without notice.

General
Information

Application Information

Motor Pricing

STAnDArD SIze rOller BeArInG AnD
STAnDArD SHAFT
5000
4000

3000

3000

2000

1600

FRAME
CD500AT

1100
1000
900
800
700

Modifications
Pricing

1500

CD360AT & CD400AT

600
500

CD320AT

400

Accessories &
Modifications

300

200

L10 BEARING LIFE (HOURS)

100000
90000
80000
70000
60000

50000

40000

30000

20000

10000
9000
8000
7000

6000

5000

4000

3000

2000

1000

100

Outline
Dimensions

MAXIMUM RADIAL LOAD, W., AT END OF SHAFT (LBS.)

10000

10000

5000

5000
4000
3000

2500

FRAME
CD5010AY

2100
1800

2000

Application
Information

3500

FRAME
CD500AT

1500

CD400AT
CD360AT
CD320AT

1000
900
800
700

Other

600
500
400
300

200

•

800-541-7191

100000
90000
80000
70000
60000

www.gemotors.com

50000

L10 BEARING LIFE (HOURS)

40000

30000

20000

10000
9000
8000
7000

6000

5000

4000

3000

2000

1000

100

Terms

MAXIMUM RADIAL LOAD, W., AT END OF SHAFT (LBS.)

OVerSIze rOller BeArInG AnD OVerSIze SHAFT

GEP387M 09/11 • Prices and data subject to change without notice.

5.9

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Application Information

Power Supplies

is	manufacturers’	data	taken	under	controlled	conditions.	
When DC motors are operated from rectified power supplies, This	data	is	generally	taken	at	no	load,	at	a	specific	distance	
from the source, and is measured in dB’s of sound pressure
the pulsating voltage and current wave forms affect the
with a reference pressure of 0.00002 N/m2. Another
motor performance by increasing motor heating and
measure of the intensity of the noise which is becoming
degrading commutating. Because of these effects, it is
necessary that the motors be designed or specially selected more accepted is sound power. This is a measure of the
intensity of the noise at its source. It is arrived at
to suit this type of operation.
mathematically through an array of sound pressure
A motor may, under some conditions, be operated from a
readings. The units of sound power are also dB’s with a
power supply different from that indicated on the nameplate.
reference power of 1012 watts. This number is the noise level
Because the three letters used to identify power supplies in
of the source and is independent of the surroundings. It can
common use have been chosen in alphabetical order of
be used to predict resulting sound pressure levels.
increasing magnitude of ripple current, a motor rated on the
Often,	in	talking	of	sound	pressure,	weighting	networks	will	
basis of an “E” power supply may be operated from a “C” or
be specified. These are sound pressure readings with certain
“D” power supply, and a motor rated on the basis of “D”
power supply may be operated from an “C” power supply but frequencies omitted to more nearly match the frequency
response	of	the	human	ear	(e.g.	“A”	network).	While	“A”	
not necessarily from an “E” power supply. If it is desired to
network	dB	levels	may	be	the	same	for	two	noise	sources,	it	
use a motor rated on the basis of a “C” power supply on
is important to realize that they may sound very different to
either a “D” or “E” power supply, it may be necessary to add
the ear. The ear is much more sensitive to dB levels of a
an inductance externally to the motor, in order to limit the
narrow frequency range. Discreet frequency sources may
ripple current to the magnitude implied in the rating. For
be	objectionable,	even	though	the	overall	“A”	network	dB	
more information see page 2.XX (previously page 62) or
level is moderate.
contact GE.
Typical values for the Kinamatic line of DP and TEFC frame
The nameplates of DC motors intended for operation from
rectified power supplies will be stamped with a Power Supply diameters are given on the following pages. For guaranteed
values, refer to GE. The values are in sound power and are no
Identification as described under POWER SUPPLY IDENTIFIload	readings	taken	using	MG	set	power.	(Noise	levels	at	full	
CATION and the external reactance required, if necessary.
load are essentially the same as no load for MG set power.)
Audio noise
To	estimate	the	average	sound	pressure,	“A”	network	at	
Noise, by definition, is unwanted sound as is, therefore, a
some distance from the machine, use the curve on the
form	of	air	pollution	which	must	be	kept	under	control.	The	
following page to obtain the ∆dB to subtract from the sound
occupational noise exposure standard promulgated by the
power value.
Occupational Safety and Health Administration (OSHA) states Blower ventilated motors will generally be quieter than
that “protection against the effects of noise exposure shall
self-ventilated motors.
be provided when the sound levels exceed those shown in
Adding one noise source equal to an existing noise source
table G-16 of the OSHA standard, when measured on the A
increases the total sound level 3dB.
scale of a standard sound level meter at slow response.” It is
Although the rectified magnetic noise levels for frames
important	to	note	that	this	standard	applies	to	the	working	
CD210AT-CD320AT never exceed 81 dB(A), rectified noise is
environment and not to any specific device such as an
electrical machine. Protection against noise exposure can be in a limited frequency range and may be more
objectionable to the ear than “white” noise, which
handled in three ways: reduction in the level of the noise
source, reduction in the transmission of noise, and control of consists of a variety of frequencies.
noise at the receiver by protective equipment.
For average sound pressure (Lp) dB(A) of a hemisphere with a
3 ft. radius, subtract 7dB(A). For 6 ft. radius, subtract 13dB(A).
Since	the	noise	to	which	a	worker	may	be	exposed	is	a	
For 10 ft. radius, subtract 17dB(A).
function of all the noise sources around him/her, as well as
the acoustical characteristics of the area, it is impossible,
without	a	detailed	knowledge	of	these	values,	to	predict	
sound	pressure	levels	on	the	workers’	ears.	What	is	available	

5.10

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

General
Information

Application Information

FeeT FrOM THe CenTer BOTTOM OF THe MOTOr
(CenTer OF nOISe SOUrCe)
FEET FROM THE CENTER BOTTOM OF THE MOTOR (CENTER OF NOISE SOURCE)

Motor Pricing

20

15
∆dB
10

Modifications
Pricing

SOUND PRESSURE – SOUND POWER TRANSITION
CURVE “A” NETWORK
SOUND PRESSURE (REFERENCE .0002 MICROBARS) –
SOUND POWER – ∆dB

5

0
6

8

10

12

14

16

Application
Information

Outline
Dimensions

Accessories &
Modifications

4

Other

2

Terms

0

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

5.11

The following noise levels have been measured on typical machines of the listed frame size
and are not guaranteed limits.

CD500AT

105

CD287AT, CD288AT

100

CD258AT, CD259AT
CD250AT

95

CD210AT

90

CD180AT

85
80
75
70
65
60
1000

2000

3000

4000

100
95

CD500AT

90

CD400AT

85

CD360AT
CD320AT
CD287AT, CD288AT

80

CD258AT, CD259AT

75

CD210AT

70

CD180AT

65
60
55
50
0

1000

MOTOR SPEED RPM

Outline
Dimensions

2000

3000

4000

MOTOR SPEED RPM

nOISe leVelS FOr TYPICAl DPFG MOTOrS WITH MOTOr MOUnTeD BlOWerS
Without Filter (Without Internal Fan) Operated From MG Set Supply
110

120

105

115

100
95
CD504AT-CD5010AY

90

CD320AT-CD400AT

85
CD280AT

80

AVERAGE SOUND POWER LEVEL
(Lw) dB(A) RE 10-12 WATTS

AVERAGE SOUND POWER LEVEL (Lw) dB(A) RE 10-12 WATTS

Application
Information
Other

CD400AT
CD360AT

AVERAGE SOUND POWER LEVEL (Lw) dB(A) RE 10-12 WATTS

110

0

Terms

nOISe leVelS FOr TYPICAl DPFG DC MOTOrS
Without Internal Fan (enclosed Separately Ventilated but
Without external Air Supply) Operated from MG Set Supply

nOISe leVel FOr TYPICAl DPFG DC MOTOrS
(With Internal Fan) Operated from MG Set Supply
AVERAGE SOUND POWER LEVEL (Lw) dB(A) RE 10-12 WATTS

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Application Information

CD6900 CD6800

110

CD6700
CD6200

105
100

CD6000

95
90

CD250AT

75

CD210AT
CD180AT

70

0
0

500

1000

1500

MOTOR SPEED RPM

65
60
0

1000

2000

3000

4000

MOTOR SPEED RPM

5.12

CD6100

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

2000

2500

Air Flow requirements for Separately Ventilated Motors
C

enclosed
Separately
Ventilated

Blown From
Drive end

Base
Speed
rPM

CFM

Standard
Separately
Ventilated

3500
2500
1750*

70
50
35

1.0
.6
.3

1.0
.6
.3

N/A
N/A
N/A

CD210AT

3500
2500
1750*

180
130
90

1.6
.8
.4

2.96
1.5
.74

3.7
1.9
.9

CD250AT

3500
2500
1750*

320
230
160

1.8
.86
.45

3.28
1.66
.82

4.0
2.0
1.0

CD280AT

3500
2500
1750*

540
385
270

2.16
1.04
.54

3.92
1.96
.98

4.3
2.4
1.2

CD320AT

ALL

650

2.0

3.2

3.0

CD360AT

ALL

610

2.2

3.9

3.4

CD400AT

ALL

830

2.6

3.65

4.0

CD504ATCD5010AY

ALL

1425

3.0

4.1

3.8

Frame
CD180AT

Frame

HP

Base
Speed
rPM

CFM

Static
Pressure
Inches of
Water

CD6000

ALL

ALL

2400

3

CD6100

ALL

ALL

3400

3

CD6200

ALL

ALL

4000

5

CD6700

ALL

ALL

5000

5

CD6800

≤1500
>1500

ALL
ALL

6200
8000

5
8

CD6900

≤2000
>2000

ALL
ALL

7500
10000

5
9

Motor Pricing

B

nOTe: Airflows are for clean dry air less than 40°C (104°F) and at
altitudes less than 1000 M (3330 FT).

WArnInG:
The static pressure values listed in the tabulations are based upon
standard air inlet and standard air outlet utilization. The static
pressure will be higher if either the air inlet or outlet openings are
restricted in size or, in the case of air outlets, reduced in number.

*1750 RPM or lower
A. Standard Separately Ventilated
Air in one CE opening with solid covers on other CE openings. Standard louvered
covers on DE air outlets.

Outline
Dimensions

B. enclosed Separately Ventilated (Air ducted in an air ducted out)
Air in one CE opening with solid covers on other CE opening. Air out one DE opening.

eSV

CD6000 and Above

SV

eSV

SV

Standard Air Inlet Location

CE TOP

CE TOP

DE*

DE*

Standard Air Exit Location

DE
(either side)

DE Side and
Bottom

CE*

CE**

eSV - enclosed Separately Ventilated
SV - Separately Ventilated

Other

Ce - Commutator end
De - Drive end

Application
Information

C. Blown From Drive end
Air in one DE opening with solid covers on other DE openings. Standard louvered
covers on CE air outlets.

CD5010AY and Below

Modifications
Pricing

A

Accessories &
Modifications

STATIC PreSSUre InCHeS OF WATer

General
Information

Application Information

Terms

*Motors are shipped with solid covers on both sides and top and bottom. Any DE cover may be
removed for air entry and any CE cover for air exit. If a transparent cover is ordered, it will be
located on the CE, conduit box side.
**If a transparent cover is ordered, air exit is opposite conduit box side and bottom. If not
transparent cover is ordered, air is exited on both sides.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

5.13

Blower Data for Blower Ventilated Motors

Frame

HP

CD180AT
CD210AT
CD258AT, CD259AT
CD287AT, CD288AT
CD320AT
CD360AT
CD400AT
CD504AT-CD5010AY

1/12
1/12
1/12
1/3
1
1
1
2

CD6000
CD6100
CD6200
CD6700
CD6800	<=	1500	HP
> 1500 HP

5
7.5
10
15
15
15

CD6900	<=	2000	HP
> 2000 HP

20
20

Hertz

Phase

rPM

Full load
Amperes

230/460
230/460
230/460
200-230/460
200-230/460
200-230/460
200-230/460
200-230/460
230/460
230/460
230/460
230/460
230/460

60
60
60
60
60
60
60
60
60
60
60
60
60

3
3
3
3
3
3
3
3
3
3
3
3
3

3600
3600
3600
3600
3600
3600
3600
1800
1800
1800
1800
1800
1800

1.0/.50
1.0/.50
1.0/.50
1.8/.9
3.0/1.5
3.0/1.5
3.0/1.5
5.8/2.9
13.4/6.7
19.6/9.8
25.2/12.6
38.8/19.4
38.8/19.4

230/460

60

3

1800

Volts

HP

1/12
1/12
1/12
1/3
1
1
1
2
3
5
7.5
10
10
REFER TO GE
49.6/24.8
15
REFER TO GE

Phase

380
380
380
380
380
380
380
380
380
380
380
380
380

50
50
50
50
50
50
50
50
50
50
50
50
50

3
3
3
3
3
3
3
3
3
3
3
3
3

3000
3000
3000
3000
3000
3000
3000
1500
1500
1500
1500
1500
1500

N/A
N/A
N/A
0.76
1.6
1.6
1.6
3.0
5.2
8
11.4
15.8
15.8

380

50

3

1500

22.4

Volts

The use of a 50 Hertz blower may affect motor frame size and will affect motor price and delivery. Refer to GE for use of 50 Hertz blowers.
Full load amperes for blower motors are typical values.
Suitable	for	operation	with	up	to	±10%	variation	from	rated	voltage	(e.g.	207-253V/414-506V,	60	Hz;	342-418V,	50	Hz)

Application
Information
Other
Terms
5.14

www.gemotors.com

•

800-541-7191

Full load
Amperes

Hertz

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Application Information

GEP387M 09/11 • Prices and data subject to change without notice.

rPM

Phase

rPM

2

1/2

380

50

3

3000

3

3600

2

1

380

50

3

3000

60

3

3600

2

3

380

50

3

3000

230/460
230/460

60
60

3
3

3600
3600

1
1

7.5
3

380
380

50
50

3
3

3000
3000

5

230/460

60

3

3600

2

5

380

50

3

3000

1
1

7.5
5

230/460
230/460

60
60

3
3

3600
3600

1
1

7.5
5

380
380

50
50

3
3

3000
3000

CD6200

1
1

10
5

230/460
230/460

60
60

3
3

3600
3600

1
1

10
5

380
380

50
50

3
3

3000
3000

CD6700

1
2

15
5

230/460
230/460

60
60

3
3

3600
3600

1
2

15
5

380
380

50
50

3
3

3000
3000

CD6800	<=	1500HP

1
2

20
7.5

230/460
230/460

60
60

3
3

3600
3600

1
2

20
7.5

380
380

50
50

3
3

3000
3000

> 1500HP

1
2

25
7.5

230/460
230/460

60
60

3
3

3600
3600

1
2

25
7.5

380
380

50
50

3
3

3000
3000

CD6900	<=	2000HP

1
2

20
7.5

230/460
230/460

60
60

3
3

3600
3600

1
2

20
7.5

380
380

50
50

3
3

3000
3000

> 2000HP

1
2

30
10

230/460
230/460

60
60

3
3

3600
3600

1
2

30
7.5

380
380

50
50

3
3

3000
3000

Hertz

Phase

2

1/2

230/460

60

3

CD400AT and
CD504AT-CD508AT
“A” COOLER

2

1

230/460

60

CD504AT-CD508AT
“B” COOLER

2

3

230/460

CD5010AY

1
1

5
3

CD6000

2

CD6100

Volts

Volts

Hertz

HP

Hertz

Phase

rPM

HP

Hertz

Phase

rPM

CD508AT

7.5

Volts
230/460

60

3

3600

5

Volts
380

50

3

3000

CD6000

7.5

230/460

60

3

3600

7.5

380

50

3

3000

CD6100

7.5

230/460

60

3

3600

7.5

380

50

3

3000

CD6200

10

230/460

60

3

3600

10

380

50

3

3000

CD6700

15

230/460

60

3

3600

15

380

50

3

3000

CD6800	<=	1500HP
>=	1500HP

20
20

230/460
230/460

60
60

3
3

3600
3600

15
20

380
380

50
50

3
3

3000
3000

CD6900	<=	2000HP
>=	2000HP

20
30

230/460
230/460

60
60

3
3

3600
3600

20
25

380
380

50
50

3
3

3000
3000

Application
Information

Blower Data for TeWAC Motors
Frame

Modifications
Pricing

HP

3600

HP

CD360AT

Frame

Outline
Dimensions

rPM

Blower
Motor
Qty.

Blower
Motor
Qty.

Accessories &
Modifications

Blower Data for TeAAC Motors

Motor Pricing

General
Information

Application Information

	Suitable	for	operation	with	up	to	±10%	variation	from	rated	voltage	(e.g.	207-253V/414-506V,	60	Hz;	342-418V,	50	Hz).	

Other

Refer to Page 124 and 125 for Kinamatic and pages 141 through 144 for CD6000, for cooler dimensions used on specific motor ratings.
Severe duty high efficiency motor option is also available. Refer to GE.
575 volts also available, contact GE for more information.

Terms

The use of 50 Hertz blower may effect motor frame size and will effect motor price and delivery. Refer to GE for use of 50 Hertz blowers.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

5.15

General
Information

Application Information

Motor load Characteristics
Constant Torque Drives

DC motors operated with fixed shunt field excitation and
adjustable armature voltage have an approximately
constant torque capacity over their speed range.

*Fig 1. Typical speed regulation

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

Many industrial applications such as conveyors, mixers,
cement	kilns,	squeeze	rolls,	continuous	processing	machines,	
etc., require nearly constant torque over their operating
speed range. (Refer to Fig. 2.)

*Fig 2. Torque and HP Characteristics of constant-horsepower, constant torque load

5.16

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Stalled Current Capability
The Continuous Load section defines the torque capability at
all speeds considering the thermal limits. While the curves
may seem to indicate an intersection at zero speed, the data
only applies at speeds other than zero, but may be very low,
such as 10 RPM. At zero speed, localized heating of the
segments under the brushes may produce segment
distortion and resulting brush vibration.

Applications such as the center-driven winding reel often
require a combination of constant torque and constant
horsepower. (See Fig. 2 on the previous page) The
horsepower required for a given linear speed of material
is constant during the build-up of a roll. However, it is
often desirable to change the surface speed when reeling
different material. Since horsepower is proportional to the
surface speed, armature voltage control will provide for the
surface speed adjustments while the field control will provide
the constant horsepower requirement during the build-up of
the roll.

Accessories &
Modifications

Constant Horsepower Drives

Motor Pricing

and Constant Torque

HP	=	 RPM x Torque
5,252

Modifications
Pricing

horsepower requirements of the load must be available at
The load torque of a driven machine can be measured by
wrapping a rope or cable around their input shaft or by using the lowest operating speed obtained by armature voltage
control.
a torque arm and applying a steady pull through a spring
scale. The horsepower can then be calculated using the
Combination of Constant Horsepower
following relation:

General
Information

Application Information

A common example of a constant horsepower drive is a
center driven winding reel. The material is wound on the
mandrel at constant linear speed and constant tension
using the following relation:

Outline
Dimensions

HP	= Linear Speed (FPM) x Tension (lb)
33,000

Application
Information

The horsepower is constant. At the start of the winding
process, the torque requirement is low because of the small
radius and the high rotational (motor) speed. As the roll
builds up, the radius increases with a resulting increase in
torque. The rotational speed must decrease in order to
maintain constant linear speed.

Other

The	main	drives	of	metal	working	machines	require	approximately constant horsepower because an optimum cutting
speed is maintained for particular types of material regardless of the diameter of the surface being machined. When
machining	small	diameter	stock,	the	torque	requirement	is	
low	and	the	rotational	speed	is	high.	Stock	of	larger	diameters require higher torque and decreased rotational speed.
DC motors operated by field control and a constant armature voltage have a constant horsepower capacity over the
speed range. (See Fig. 2 on the previous page)

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Terms

In some applications, constant horsepower may be required
over a wider speed range than is obtainable by field control.
The additional speed range must be obtained by armature
voltage control. Horsepower and speed are approximately
proportional to the applied armature voltage, and the

5.17

notes

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Application Information

5.18

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Other Information

Page
Field Modification Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2

General
Information

Index

Standard Bearing Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5
Authorized Motor Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Terms and Conditions for Sale of Products and Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7

Motor Pricing

Recommended Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

6.1

Field Modification Kits

Custom Modification Kits
Custom modification kits allow modification of Kinamatic™
motors which have been shipped from the factory. They are
designed for maximum flexibility and ease of installation,
and are stocked by authorized GE parts distributors to
provide immediate availability.
The quick kit reference on the following pages lists the
numbers of the most commonly used accessory kits and
modification by frame size. Field modification kits cannot be
mounted on all frame sizes or enclosures. Please review the
application information carefully to determine availability.
Contact GE (phone number available on page 6.4 of this
document) or your GE parts distributor for kit prices.
The information given is not to be used for new motor
specifications.
Blower Kits
Blower kits are designed for standard mounting on the
motor commutator end and for addition only to dripproof
fully guarded, separately ventilated motors. Blower motors
are 230/460 volt AC, 3 phase, 60 Hertz. To properly mount a
blower kit on CD180AT frames, drilling and tapping of three
holes is required.
Tachometer Kits
Tachometer kits are designed to be mounted on motors
with an accessory comm end shaft extension of any fully
guarded or totally enclosed Kinamatic motor, with the

PY TACH KIT
LESS TACH

Frame Series

Type C-Face Endshield Kits
Type C-Face endshield kits are designed for mounting on the
fully guarded or totally enclosed nonventilated (TENV) frames
listed below. Addition of Type C-Face endshield kits requires
machine disassembly by a qualified service facility. For
frames CD218AT-CD2010AT, refer to factory.
Frame Series

Standard C-Face Dimension (in inches)

CDL182AT-CD259AT

8.5

CD287AT & CD288AT

10.5

CD327AT, CD328AT, CD329AT

12.5

Sliding Bases
Sliding bases are suggested as a convenient means for
adjusting belt tension or may be used as mounting plates.
(For horizontal mounting only — not available for ceiling or
sidewall mounting. Sliding bases not available on CD6000
frames and above.)
Lexan® Covers
Lexan® covers are suggested as a convenient means of
viewing brush rigging and brushes. Not available on frame
sizes CDL182AT-CD189AT.

BC TACH KIT
LESS TACH

AN-AC TACH
45/90V/1000RPM
(INCLUDES TACH)

CDL182AT-CD329AT

36A167701AAG01

36A167700AAG01

36A167702AAG01

CD365AT-CD368AT

36A167701BAG01

36A167700BAG01

36A167702BAG01

CD407AT-CDL409AT

36A167701CAG01

36A167700CAG01

36A167702CAG01

CD504AT-CD5010AY

36A167701CAG14

36A167700CAG01

36A167702DAG01

Frame Series

AN-DG240L3
240 PPR
ONE OUTPUT

AN-DG240L4
240 PPR
DUAL OUTPUT

AN-DG600L3
600 PPR
ONE OUTPUT

AN-DG600L4
600 PPR
DUAL OUTPUT

CDL182AT-CD329AT

36C706050DA001

36C706050DB001

36C706050DC001

36C706050DD001

CD365AT-CD368AT

36C706050AB001

36C706050AB001

36C706050AC001

36C706050AD001

CD407AT-CDL409AT

36C706050AB002

36C706050AB002

36C706050AC002

36C706050AD002

CD504AT-CD5010AY

36C706050AB003

36C706050AB003

36C706050AC003

36C706050AD003

*Bi-directional, dual output.

Terms

Other

exception of totally enclosed fan cooled (TEFC) machines.
Tach adapters are made of cast iron and are supplied
with appropriate covers. Refer to GE for mounting of
tachometer kits on TEFC motors. Note: Type BC and Type
PY tachometers must be ordered independently of the
tachometer kits less tachometer.

Application Information

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Frames CD180AT to CD5010AY

6.2

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Field Modification Kits

DC BC46 TACH ONLY
(USES BC KIT)

50V/1000 RPM

897A594-002

50V/1000 RPM

897A590-032

50V/1000 RPM

897A591-041

100V/1000 RPM

897A594-001

100V/1000 RPM

897A590-024

100V/1000 RPM

897A591-029

BLOWER KIT
LESS FILTER

BLOWER KIT
WITH FILTER

CD218AT-CD2110AT

36A167741CAG01
36A167742AAG02

36A167741CBG01
36A167742ABG02

36A172472AAG01

36A167802BAG02

CD258AT-CD259AT

36A167743AAG02

36A167743ABG02

36A172473AAG01

36A167803BAG02

CD287AT-CD288AT

36A167744AAG03

36A167744ABG03

36A172474AAG01

36A167805BAG02

CD327AT-CD329AT

36A167745GAG10

36A167745GBG10

36A172475AAG01

36A167806BAG02

CD365AT-CD368AT

36A167746GAG10

36A167746GBG10

NOT AVAILABLE

36A167807BAG02

Frame Series
CDL182AT-CD189AT

C-FACE KIT

LEXAN® COVERS
(Qty. 2 required)
NOT AVAILABLE

36A167747GAG10

36A167747GBG10

NOT AVAILABLE

36A167809BAG02

36A167747GCG10

36A167747GDG10

NOT AVAILABLE

36B473083CAG01

CD504AT-CD5010AY

36A167749EAG30

36A167749EBG34

NOT AVAILABLE

36B473084CAG01

533C400-001
533C400-001

CD189AT

533C400-023

CD218AT

533C400-019

CD219AT

533C400-022

CD2110AT

533C400-039

CD258AT

533C400-040

CD259AT

533C400-041

CD287AT

533C400-020

CD288AT

533C400-042

CD327AT

533C400-043

CD328AT

533C400-044

CD329AT

533C400-067

CD365AT

533C400-011

CD366AT

533C400-012

CD368AT

533C400-046

CD407AT

533C400-047

CDL407AT

533C400-047

CD409AT

533C400-048

CDL409AT

533C400-048

CD504AT

533C400-017

CDL504AT

533C400-017

CD506AT

533C400-049

CDL506AT

533C400-049

CD508AT

533C400-050

CDL508AT

533C400-050

CD5010AY

533C400AK001

Outline
Dimensions

CD186AT
CDL186AT

Application
Information

533C400-034

Other

Sliding Base

CDL182AT

Accessories &
Modifications

CD407AT & CD409AT
CDL407AT & CDL409AT

Frame Series

Motor Pricing

DC BC42 TACH ONLY
(USES BC KIT)

Modifications
Pricing

DC PY TACH ONLY
(USES PY KIT)

General
Information

Frames CD180AT to CD5010AY

www.gemotors.com

•

800-541-7191

Terms

Blower motor is 230/460 Volt AC, 3 phase, 60 Hertz.
Requires drilling and tapping of three holes to install.
Requires motor disassembly by qualified service facility to install.
For dripproof motors use 36A172471AAG02. For totally enclosed motors
use 36A172471AAG01.
For commutator end only.

GEP387M 09/11 • Prices and data subject to change without notice.

6.3

Renewal Parts Service

Parts available directly from authorized GE parts distributors.
For authorized distributor information or technical support,
call toll free: 1-877-458-0451.

The Kinamatic motor is designed for tough industrial applications. Maintain the original performance standards of the
Kinamatic design by using genuine GE renewal parts.

Repair service is available from authorized GE service
facilities.

Kinamatic renewal parts, such as main and commutator
coils, pole assemblies, and armature coils are produced to
original factory specifications including form fits, materials,
and dimensions.

Recommended Spare Parts
As insurance against costly downtime, it is strongly
recommended that spare parts be kept on hand in
accordance with the chart below:

A permanently attached stainless steel nameplate displays
the model and serial number, providing all the information
needed for ordering.

NUMBER OF DUPLICATE MOTORS IN SERVICE

Description

1

2-4

5-10

11-20

More Than 20

Complete Machine

-

-

-

1

2

Drive End Ball Bearing

1

1

1

2

3

Front End Ball Bearing

1

1

1

2

3

Brushes (Sets)

2

4

4

8

10

Brushholders (Sets)

-

1

1

1

1

Brushholder Springs (Sets)

1

1

1

2

2

Main Field Coil and Pole

-

1

1

2

3

Commutating Field Coil and Pole

-

1

1

2

3

Armature, Complete

-

1

1

2

2

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Recommended Spare Parts List

6.4

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

General
Information

Standard Bearing Information

Motor Pricing

The following chart shows the standard ball bearings used in
Kinamatic motors. This chart does not apply to motors with
roller bearings. Non-standards are manufactured for special
applications. Therefore, not all Kinamatic motors follow the
chart below. Refer to GE for non-standard motors.
STANDARD BEARINGS FOR DC MOTORS

GE Part Number

Bearing Size

AFBMA #

GE Part Number

CD140AT

6205

25BC02JPP3

894A605ZJ 005

6204

20BC02JPP3

894A605ZJ 004

CD180AT

6206

30BC02JPP3

894A605ZJ 006

6206

30BC02JPP3

894A605ZJ 006

CD210AT

6207

35BC02JPP3

894A605ZJ 007

6206

30BC02JPP3

894A605ZJ 006

CD250AT

6209

45BC02X3

894A605 009

6207

35BC02X3

894A605 007

CD280AT

6210

50BC02X3

894A605 010

6209

45BC02X3

894A605 009

CD320AT

6211

55BC02X3

894A605 011

6210

50BC02X3

894A605 010

6213

65BC02X3

894A605 013

6211

55BC02X3

894A605 011

6214

70BC02X3

894A605 014

6213

65BC02X3

894A605 013

CD504AT/CD508AT

6218

90BC02X3

894A605 018

6216

80BC02X3

894A605 016

CD5010AY

6222

110BC02X3

894A605 022

6218

90BC02X3

894A605 018

CD6000

6224

120BC02X3

894A605 023

6220

100BC02X3

894A605 020

CD6100

6228

140BC02X3

894A605 025

6224

120BC02X3

894A605 023

CD6200

6232

160BC02X3

894A605 027

6228

140BC02X3

894A605 025

CD6700

6236

180BC02X3

894A605 029

6236

180BC02X3

894A605 029

CD6800

6236

180BC02X3

894A605 029

6236

180BC02X3

894A605 029

CD6900

6240

200BC02X3

894A605 031

6240

200BC02X3

894A605 031

Terms

Other

Application
Information

CD360AT
CD400AT

Accessories &
Modifications

AFBMA #

Modifications
Pricing

COMM END

Bearing Size

Outline
Dimensions

Frame Size

DRIVE END

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

6.5

Authorized Motor Service Centers

Before warranty service is commenced on any Motors product, please contact Post Sale Service at:
USA and Canada: (866) 563-1284
International:
(260) 439-4451
Email:
gemotorspss@ge.com
Visit us online to find an authorized motor service center in your region.

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

www.gemotors.com

6.6

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Terms and Conditions for Sale of Products and Services

“Insolvent/Bankrupt” means that a party is insolvent, makes
an assignment for the benefit of its creditors, has a receiver
or trustee appointed for it or any of its assets, or files or
has filed against it a proceeding under any bankruptcy,
insolvency dissolution or liquidation laws.
“Products” means the equipment, parts, materials, supplies,
software, and other goods Seller has agreed to supply to
Buyer under the Contract.

www.gemotors.com

•

800-541-7191

guarantee allowing for pro-rata payments as Products are
shipped and Services are performed, plus payment of
cancellation and termination charges, and all other amounts
due from Buyer under the Contract (“Payment Security”). The
Payment Security shall be (a) in a form, and issued or
confirmed by a bank acceptable to Seller, (b) payable at the
counters of such acceptable bank or negotiating bank, (c)
opened at least sixty (60) days prior to both the earliest
scheduled shipment of Products and commencement of

GEP387M 09/11 • Prices and data subject to change without notice.

6.7

Motor Pricing
Modifications
Pricing

2.1 Buyer shall pay Seller for the Products and Services by
paying all invoiced amounts in U.S. dollars, without set-off
for any payment from Seller not due under this Contract,
“Contract” means either the contract agreement signed by
within thirty (30) days from the invoice date. If the Contract
both parties, or the purchase order signed by Buyer and
Price is less than U.S. Two Hundred Fifty Thousand Dollars
accepted by Seller in writing, for the sale of Products or
($250,000), Seller shall issue invoices upon shipment of
Services, together with these Terms and Conditions, Seller’s
Products and as Services are performed. If the Contract Price
final quotation, the agreed scope(s) of work, and Seller’s
is U.S. Two Hundred Fifty Thousand Dollars ($250,000) or
order acknowledgement. In the event of any conflict, the
more, progress payments shall be invoiced starting with
Terms and Conditions shall take precedence over other
twenty-five percent (25%) of the Contract Price for Products
documents included in the Contract.
and Services upon the earlier of Contract signature or
“Contract Price” means the agreed price stated in the
issuance of Seller’s order acknowledgement and continuing
Contract for the sale of Products and Services, including
such that ninety percent (90%) of the Contract Price for
adjustments (if any) in accordance with the Contract.
Products is received before the earliest scheduled Product
shipment and Services are invoiced as performed (“Progress
“Hazardous Materials” means any toxic or hazardous
Payments”). For each calendar month, or fraction thereof,
substance, hazardous material, dangerous or hazardous
that payment is late, Buyer shall pay a late payment charge
waste, dangerous good, radioactive material, petroleum or
computed at the rate of 1.5% per month on the overdue
petroleum-derived products or by-products, or any other
chemical, substance, material or emission, that is regulated, balance, or the maximum rate permitted by law, whichever
listed or controlled pursuant to any national, state, provincial, is less.
or local law, statute, ordinance, directive, regulation or other 2.2 As and if requested by Seller, Buyer shall at its expense
legal requirement of the United States (“U.S.”) or the country
establish and keep in force payment security in the form of
of the Site.
an irrevocable, unconditional, sight letter of credit or bank
“Buyer” means the entity to which Seller is providing
Products or Services under the Contract.

Accessories &
Modifications

“Terms and Conditions” means these “Terms and Conditions
for Sale of Products and Services”, including any relevant
addenda pursuant to Article 18, together with any modifications or additional provisions specifically stated in Seller’s final
quotation or specifically agreed upon by Seller in writing.

Outline
Dimensions

2. Payment

“Site” means the premises where Products are used or
Services are performed, not including Seller’s premises from
which it performs Services.

Application
Information

1. Definitions

“Services” means the services Seller has agreed to perform
for Buyer under the Contract.

Other

“Seller” means the entity providing Products or performing
Services under the Contract.

Terms

NOTICE: Sale of any Products or Services is expressly
conditioned on Buyer's assent to these Terms and Conditions. Any acceptance of Seller’s offer is expressly limited
to acceptance of these Terms and Conditions and Seller
expressly objects to any additional or different terms
proposed by Buyer. No facility entry form shall modify
these Terms and Conditions even if signed by Seller’s
representative. Any order to perform work and Seller's
performance of work shall constitute Buyer’s assent to
these Terms and Conditions. Unless otherwise specified in
the quotation, Seller’s quotation shall expire 30 days from
its date and may be modified or withdrawn by Seller
before receipt of Buyer’s conforming acceptance.

General
Information

Form ES 104 (Rev. 4)

Terms and Conditions for Sale of Products and Services

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Form ES 104 (Rev. 4)

Services, and (d) remain in effect until the latest of ninety (90)
days after the last scheduled Product shipment, completion
of all Services and Seller’s receipt of the final payment
required under the Contract. Buyer shall, at its expense,
increase the amount(s), extend the validity period(s) and
make other appropriate modifications to any Payment
Security within ten (10) days of Seller’s notification that such
adjustment is necessary in connection with Buyer’s obligations under the Contract.

Seller’s facility or warehouse (Incoterms 2010). For export
shipments, Seller shall deliver Products to Buyer FCA Port of
Export (Incoterms 2010). Buyer shall pay all delivery costs
and charges or pay Seller’s standard shipping charges plus
up to twenty-five (25%) percent. Partial deliveries are
permitted. Seller may deliver Products in advance of the
delivery schedule. Delivery times are approximate and are
dependent upon prompt receipt by Seller of all information
necessary to proceed with the work without interruption.
If Products delivered do not correspond in quantity, type
2.3 Seller is not required to commence or continue its
or price to those itemized in the shipping invoice or docuperformance unless and until any required Payment
Security is received, operative and in effect and all applicable mentation, Buyer shall so notify Seller within ten (10) days
after receipt.
Progress Payments have been received. For each day of
delay in receiving Progress Payments or acceptable Payment 4.2 For shipments that do not involve export, title to
Products shall pass to Buyer upon delivery in accordance
Security, Seller shall be entitled to a matching extension of
with Section 4.1. For export shipments from a Seller facility
the schedule. If at any time Seller reasonably determines
that Buyer’s financial condition or payment history does not or warehouse outside the U.S., title shall pass to Buyer
upon delivery in accordance with Section 4.1. For shipments
justify continuation of Seller’s performance, Seller shall be
from the U.S. to another country, title shall pass to Buyer
entitled to require full or partial payment in advance or
immediately after each item departs from the territorial
otherwise restructure payments, request additional forms
land, seas and overlying airspace of the U.S. The 1982 United
of Payment Security, suspend its performance or terminate
Nations Convention of the law of the Sea shall apply to
the Contract.
determine the U.S. territorial seas. For all other shipments,
3. Taxes and Duties
title to Products shall pass to Buyer the earlier of (i) the port
of export immediately after Products have been cleared for
Seller shall be responsible for all corporate taxes measured
export or (ii) immediately after each item departs from the
by net income due to performance of or payment for work
territorial land, seas and overlying airspace of the sending
under this Contract (“Seller Taxes”). Buyer shall be responsible for all taxes, duties, fees, or other charges of any nature country. When Buyer arranges the export or intercommunity
shipment, Buyer will provide Seller evidence of exportation
(including, but not limited to, consumption, gross receipts,
import, property, sales, stamp, turnover, use, or value-added or intercommunity shipment acceptable to the relevant tax
and custom authorities. Notwithstanding the foregoing,
taxes, and all items of withholding, deficiency, penalty,
Seller grants only a license, and does not pass title, for any
addition to tax, interest, or assessment related thereto,
imposed by any governmental authority on Buyer or Seller or software provided by Seller under this Contract, and title to
any leased equipment remains with Seller.
its subcontractors) in relation to the Contract or the performance of or payment for work under the Contract other than 4.3 Risk of loss shall pass to Buyer upon delivery pursuant to
Seller Taxes (“Buyer Taxes”). The Contract Price does not
Section 4.1, except that for export shipments from the U.S.,
include the amount of any Buyer Taxes. If Buyer deducts or
risk of loss shall transfer to Buyer upon title passage.
withholds Buyer Taxes, Buyer shall pay additional amounts
4.4 If any Products to be delivered under this Contract or if
so that Seller receives the full Contract Price without reducany Buyer equipment repaired at Seller’s facilities cannot be
tion for Buyer Taxes. Buyer shall provide to Seller, within one
shipped to or received by Buyer when ready due to any
month of payment, official receipts from the applicable
cause attributable to Buyer or its other contractors, Seller
governmental authority for deducted or withheld taxes.
may ship the Products and equipment to a storage facility,
4. Deliveries; Title Transfer; Risk of Loss; Storage including storage at the place of manufacture or repair, or to
an agreed freight forwarder. If Seller places Products or
4.1 For shipments that do not involve export, including
equipment into storage, the following apply: (i) title and risk
shipments from one European Union (“EU”) country to
of loss immediately pass to Buyer, if they have not already
another EU country, Seller shall deliver Products to Buyer FCA

6.8

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Terms and Conditions for Sale of Products and Services

5.3 If Products or Services do not meet the above warranties, Buyer shall promptly notify Seller in writing prior to
expiration of the warranty period. Seller shall (i) at its option,
repair or replace defective Products and (ii) re-perform
defective Services. If despite Seller’s reasonable efforts, a
non-conforming Product cannot be repaired or replaced, or
non-conforming Services cannot be re-performed, Seller
shall refund or credit monies paid by Buyer for such nonconforming Products and Services. Warranty repair, replacement or re-performance by Seller shall not extend or renew
the applicable warranty period. Buyer shall obtain Seller’s
agreement on the specifications of any tests it plans to
conduct to determine whether a non-conformance exists.
5.4 Buyer shall bear the costs of access for Seller’s remedial
warranty efforts (including removal and replacement of
systems, structures or other parts of Buyer’s facility), de
installation, decontamination, re installation and transportation of defective Products to Seller and back to Buyer.

www.gemotors.com

•

800-541-7191

6.1 Seller and Buyer (as to information disclosed, the
“Disclosing Party”) may each provide the other party (as to
information received, the “Receiving Party”) with Confidential
Information in connection with this Contract. “Confidential
Information” means (a) information that is designated in
writing as “confidential” or “proprietary” by Disclosing
Party at the time of written disclosure, and (b) information
that is orally designated as “confidential” or “proprietary” by
Disclosing Party at the time of oral or visual disclosure and is
confirmed to be “confidential” or “proprietary” in writing
within twenty (20) days after the oral or visual disclosure. In
addition, prices for Products and Services shall be considered
Seller’s Confidential Information.
6.2 Receiving Party agrees: (i) to use the Confidential
Information only in connection with the Contract and use
of Products and Services, (ii) to take reasonable measures to
prevent disclosure of the Confidential Information to third
parties, and (iii) not to disclose the Confidential Information
to a competitor of Disclosing Party. Notwithstanding these
restrictions, (a) Seller may disclose Confidential Information
to its affiliates and subcontractors in connection with
performance of the Contract, (b) a Receiving Party may
disclose Confidential Information to its auditors, (c) Buyer

GEP387M 09/11 • Prices and data subject to change without notice.

6.9

Motor Pricing
Modifications
Pricing
Accessories &
Modifications

6. Confidentiality

Outline
Dimensions

5.2 The warranty for Products shall expire one (1) year from
first use or eighteen (18) months from delivery, whichever
occurs first, except that software is warranted for ninety (90)
days from delivery. The warranty for Services shall expire
one (1) year after performance of the Service, except that
software-related Services are warranted for ninety (90) days.

Application
Information

5.6 This Article 5 provides the exclusive remedies for all
claims based on failure of or defect in Products or Services,
regardless of when the failure or defect arises, and whether
a claim, however described, is based on contract, warranty,
indemnity, tort/extra-contractual liability (including negligence), strict liability or otherwise. The warranties provided
5. Warranty
in this Article 5 are exclusive and are in lieu of all other
5.1 Seller warrants that Products shall be delivered free from warranties, conditions and guarantees whether written, oral,
defects in material, workmanship and title and that Services implied or statutory. NO IMPLIED OR STATUTORY WARRANTY,
OR WARRANTY OR CONDITION OF MERCHANTABILITY OR
shall be performed in a competent, diligent manner in
FITNESS FOR A PARTICULAR PURPOSE APPLIES.
accordance with any mutually agreed specifications.

Other

4.5 If repair Services are to be performed on Buyer’s
equipment at Seller’s facility, Buyer shall be responsible for,
and shall retain risk of loss of, such equipment at all times,
except that Seller shall be responsible for damage to the
equipment while at Seller’s facility to the extent such
damage is caused by Seller’s negligence.

5.5 The warranties and remedies are conditioned upon (a)
proper storage, installation, use, operation, and maintenance of Products, (b) Buyer keeping accurate and complete
records of operation and maintenance during the warranty
period and providing Seller access to those records, and (c)
modification or repair of Products or Services only as
authorized by Seller in writing. Failure to meet any such
conditions renders the warranty null and void. Seller is not
responsible for normal wear and tear.

Terms

passed, and delivery shall be deemed to have occurred; (ii)
any amounts otherwise payable to Seller upon delivery or
shipment shall be due; (iii) all expenses and charges incurred
by Seller related to the storage shall be payable by Buyer
upon submission of Seller’s invoices; and (iv) when conditions
permit and upon payment of all amounts due, Seller shall
make Products and repaired equipment available to Buyer
for delivery.

General
Information

Form ES 104 (Rev. 4)

Terms and Conditions for Sale of Products and Services

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Form ES 104 (Rev. 4)

may disclose Confidential Information to lenders as
necessary for Buyer to secure or retain financing needed
to perform its obligations under the Contract, and (d) a
Receiving Party may disclose Confidential Information to
any other third party with the prior written permission of
Disclosing Party, and in each case, only so long as the
Receiving Party obtains a non-disclosure commitment
from any such subcontractors, auditors, lenders or other
permitted third party that prohibits disclosure of the
Confidential Information and provided further that the
Receiving Party remains responsible for any unauthorized
use or disclosure of the Confidential Information. Receiving
Party shall upon request return to Disclosing Party or
destroy all copies of Confidential Information except to
the extent that a specific provision of the Contract entitles
Receiving Party to retain an item of Confidential Information.
Seller may also retain one archive copy of Buyer’s
Confidential Information.
6.3 The obligations under this Article 6 shall not apply to any
portion of the Confidential Information that: (i) is or becomes
generally available to the public other than as a result of
disclosure by Receiving Party, its representatives or its
affiliates; (ii) is or becomes available to Receiving Party on a
non-confidential basis from a source other than Disclosing
Party when the source is not, to the best of Receiving
Party’s knowledge, subject to a confidentiality obligation to
Disclosing Party; (iii) is independently developed by Receiving
Party, its representatives or affiliates, without reference to
the Confidential Information; (iv) is required to be disclosed
by law or valid legal process provided that the Receiving
Party intending to make disclosure in response to such
requirements or process shall promptly notify the Disclosing
Party in advance of such disclosure and reasonably
cooperate in attempts to maintain the confidentiality of
the Confidential Information.
6.4 Each Disclosing Party warrants that it has the right to
disclose the information that it discloses. Neither Buyer nor
Seller shall make any public announcement about the
Contract without prior written approval of the other party. As
to any individual item of Confidential Information, the
restrictions under this Article 6 shall expire five (5) years after
the date of disclosure. Article 6 does not supersede any
separate confidentiality or nondisclosure agreement signed
by the parties.

6.10

www.gemotors.com

•

800-541-7191

7. Intellectual Property
7.1 Seller shall defend and indemnify Buyer against any
claim by a non-affiliated third party (a “Claim”) alleging that
Products or Services furnished under this Contract infringe a
patent in effect in the U.S., an EU member state or the
country of the Site (provided there is a corresponding patent
issued by the U.S. or an EU member state), or any copyright
or trademark registered in the country of the Site, provided
that Buyer (a) promptly notifies Seller in writing of the Claim,
(b) makes no admission of liability and does not take any
position adverse to Seller, (c) gives Seller sole authority to
control defense and settlement of the Claim, and (d) provides
Seller with full disclosure and reasonable assistance as
required to defend the Claim.
7.2 Section 7.1 shall not apply and Seller shall have no
obligation or liability with respect to any Claim based upon
(a) Products or Services that have been modified, or revised,
(b) the combination of any Products or Services with other
products or services when such combination is a basis of
the alleged infringement, (c) failure of Buyer to implement
any update provided by Seller that would have prevented
the Claim, (d) unauthorized use of Products or Services,
or (e) Products or Services made or performed to Buyer’s
specifications.
7.3 Should any Product or Service, or any portion thereof,
become the subject of a Claim, Seller may at its option (a)
procure for Buyer the right to continue using the Product or
Service, or applicable portion thereof, (b) modify or replace it
in whole or in part to make it non-infringing, or (c) failing (a)
or (b), take back infringing Products or Services and refund
the price received by Seller attributable to the infringing
Products or Services.
7.4 Article 7 states Seller’s exclusive liability for intellectual
property infringement by Products and Services.
7.5 Each party shall retain ownership of all Confidential
Information and intellectual property it had prior to the
Contract. All new intellectual property conceived or created
by Seller in the performance of this Contract, whether alone
or with any contribution from Buyer, shall be owned exclusively by Seller. Buyer agrees to deliver assignment documentation as necessary to achieve that result.

GEP387M 09/11 • Prices and data subject to change without notice.

Terms and Conditions for Sale of Products and Services

10. Excusable Events
Seller shall not be liable or considered in breach of its
obligations under this Contract to the extent that Seller’s
performance is delayed or prevented, directly or indirectly,
by any cause beyond its reasonable control, or by armed
conflict, acts or threats of terrorism, epidemics, strikes or
other labor disturbances, or acts or omissions of any
governmental authority or of the Buyer or Buyer’s contractors or suppliers. If an excusable event occurs, the schedule
for Seller’s performance shall be extended by the amount of
time lost by reason of the event plus such additional time as
may be needed to overcome the effect of the event. If acts
or omissions of the Buyer or its contractors or suppliers
cause the delay, Seller shall also be entitled to an equitable
price adjustment.

11. Termination and Suspension
11.1 Buyer may terminate the Contract (or the portion
affected) for cause if Seller (i) becomes Insolvent/Bankrupt,

www.gemotors.com

•

800-541-7191

11.4 If the Contract (or any portion thereof) is terminated for
any reason other than Seller’s default under Section 11.1,
Buyer shall pay Seller for all Products completed, lease fees
incurred and Services performed before the effective date of
termination, plus expenses reasonably incurred by Seller in
connection with the termination. The amount due for Services
shall be determined in accordance with the milestone
schedule (for completed milestones) and rates set forth in the
Contract (for work toward milestones not yet achieved and
where there is no milestone schedule), as applicable or, where
there are no milestones and/or rates in the Contract, at
Seller’s then-current standard time and material rates. In
addition, Buyer shall pay Seller a cancellation charge equal
to 80% of the Contract Price applicable to uncompleted
made-to-order Products and 15% of the Contract Price
applicable to all other uncompleted Products.
11.5 Either Buyer or Seller may terminate the Contract (or
the portion affected) upon twenty (20) days advance notice if
there is an excusable event (as described in Article 10)

GEP387M 09/11 • Prices and data subject to change without notice.

6.11

Motor Pricing
Modifications
Pricing
Accessories &
Modifications

11.3 Seller may suspend or terminate the Contract (or any
affected portion thereof) immediately for cause if Buyer
(i) becomes Insolvent/Bankrupt, or (ii) materially breaches
the Contract, including, but not limited to, failure or delay in
Buyer providing Payment Security, making any payment
when due, or fulfilling any payment conditions.

Outline
Dimensions

During the term of the Contract, Seller shall maintain for its
protection the following insurance coverage: (i) Worker’s
Compensation, Employer’s Liability and other statutory
insurance required by law with respect to work related
injuries or disease of employees of Seller in such form(s)
and amount(s) as required by applicable laws; (ii) Automobile
Liability insurance with a combined single limit of
$2,500,000.00; and (iii) Commercial General Liability or Public
Liability insurance for bodily injury and property damage
with a combined single limit of $2,500,000.00. If required in
the Contract, Seller shall provide a certificate of insurance
reflecting such coverage.

Application
Information

9. Insurance

11.2 If Buyer terminates the Contract pursuant to Section
11.1, (i) Seller shall reimburse Buyer the difference between
that portion of the Contract Price allocable to the terminated
scope and the actual amounts reasonably incurred by Buyer
to complete that scope, and (ii) Buyer shall pay to Seller (a) the
portion of the Contract Price allocable to Products completed,
(b) lease fees incurred, and (c) amounts for Services performed
before the effective date of termination. The amount due for
Services shall be determined in accordance with the milestone schedule (for completed milestones) and rates set forth
in the Contract (for work toward milestones not yet achieved
and where there is no milestone schedule), as applicable or,
where there are no milestones and/or rates in the Contract, at
Seller’s then-current standard time and material rates.

Other

Each of Buyer and Seller (as an “Indemnifying Party”) shall
indemnify the other party (as an “Indemnified Party”) from
and against claims brought by a third party, on account of
personal injury or damage to the third party’s tangible
property, to the extent caused by the negligence of the
Indemnifying Party in connection with this Contract. In the
event the injury or damage is caused by joint or concurrent
negligence of Buyer and Seller, the loss or expense shall be
borne by each party in proportion to its degree of negligence. For purposes of Seller’s indemnity obligation, no part
of the Products or Site is considered third party property.

or (ii) commits a material breach of the Contract which does
not otherwise have a specified contractual remedy, provided
that: (a) Buyer shall first provide Seller with detailed written
notice of the breach and of Buyer’s intention to terminate
the Contract, and (b) Seller shall have failed, within 30 days
after receipt of the notice, to commence and diligently
pursue cure of the breach.

Terms

8. Indemnity

General
Information

Form ES 104 (Rev. 4)

Terms and Conditions for Sale of Products and Services

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Form ES 104 (Rev. 4)

lasting longer than one hundred and twenty (120) days.
In such case, Buyer shall pay to Seller amounts payable
under Section 11.4, excluding the cancellation charge for
uncompleted Products.
11.6 Buyer shall pay all reasonable expenses incurred by
Seller in connection with a suspension, including, but
not limited to, expenses for repossession, fee collection,
demobilization/remobilization, and costs of storage during
suspension. The schedule for Seller’s obligations shall be
extended for a period of time reasonably necessary to
overcome the effects of any suspension.

12. Compliance with Laws, Codes
and Standards
12.1 Seller shall comply with laws applicable to the
manufacture of Products and its performance of Services.
Buyer shall comply with laws applicable to the application,
operation, use and disposal of the Products and Services.
12.2 Seller’s obligations are conditioned upon Buyer’s
compliance with all U.S. and other applicable trade control
laws and regulations. Buyer shall not trans-ship, re-export,
divert or direct Products other than in and to the ultimate
country of destination declared by Buyer and specified as
the country of ultimate destination on Seller’s invoice.

13.2 Buyer shall timely advise Seller in writing of all applicable Site-specific health, safety, security and environmental
requirements and procedures. Without limiting Buyer’s
responsibilities under Article 13, Seller has the right but not
the obligation to, from time to time, review and inspect
applicable health, safety, security and environmental
documentation, procedures and conditions at the Site.
13.3 If, in Seller’s reasonable opinion, the health, safety, or
security of personnel or the Site is, or is apt to be, imperiled
by security risks, terrorist acts or threats, the presence of or
threat of exposure to Hazardous Materials, or unsafe
working conditions, Seller may, in addition to other rights or
remedies available to it, evacuate some or all of its personnel from Site, suspend performance of all or any part of the
Contract, and/or remotely perform or supervise work. Any
such occurrence shall be considered an excusable event.
Buyer shall reasonably assist in any such evacuation.
13.4 Operation of Buyer’s equipment is the responsibility of
Buyer. Buyer shall not require or permit Seller’s personnel to
operate Buyer’s equipment at Site.
13.5 Buyer will make its Site medical facilities and resources
available to Seller personnel who need medical attention.

13.6 Seller has no responsibility or liability for the pre-existing
condition of Buyer’s equipment or the Site. Prior to Seller
12.3 Notwithstanding any other provision, Buyer shall timely starting any work at Site, Buyer will provide documentation
obtain, effectuate and maintain in force any required permit, that identifies the presence and condition of any Hazardous
license, exemption, filing, registration and other authorizaMaterials existing in or about Buyer’s equipment or the Site
tion, including, but not limited to, building and environmental that Seller may encounter while performing under this
permits, import licenses, environmental impact assessments, Contract. Buyer shall disclose to Seller industrial hygiene and
and foreign exchange authorizations, required for the lawful environmental monitoring data regarding conditions that may
performance of Services at the Site or fulfillment of Buyer’s
affect Seller’s work or personnel at the Site. Buyer shall keep
obligations, except that Seller shall obtain any license or
Seller informed of changes in any such conditions.
registration necessary for Seller to generally conduct
13.7 Seller shall notify Buyer if Seller becomes aware of:
business and visas or work permits, if any, necessary for
(i) conditions at the Site differing materially from those
Seller’s personnel. Buyer shall provide reasonable assistance
disclosed by Buyer, or (ii) previously unknown physical
to Seller in obtaining such visas and work permits.
conditions at Site differing materially from those ordinarily
encountered and generally recognized as inherent in work
13. Environmental, Health and Safety Matters
of the character provided for in the Contract. If any such
13.1 Buyer shall maintain safe working conditions at the Site, conditions cause an increase in Seller's cost of, or the time
including, without limitation, implementing appropriate
required for, performance of any part of the work under the
procedures regarding Hazardous Materials, confined space
Contract, an equitable adjustment in price and schedule
entry, and energization and de-energization of power
shall be made.
systems (electrical, mechanical and hydraulic) using safe and
13.8 If Seller encounters Hazardous Materials in Buyer’s
effective lock-out/tag-out (“LOTO”) procedures including
physical LOTO or a mutually agreed upon alternative method. equipment or at the Site that require special handling or
disposal, Seller is not obligated to continue work affected by

6.12

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Terms and Conditions for Sale of Products and Services

14.2 The scope, Contract Price, schedule, and other provisions
will be equitably adjusted to reflect additional costs or
obligations incurred by Seller resulting from a change, after
Seller’s proposal date, in Buyer’s Site-specific requirements or
procedures, or in industry specifications, codes, standards,
applicable laws or regulations. However, no adjustment will be
made on account of a general change in Seller’s manufacturing or repair facilities resulting from a change in laws or
regulations applicable to such facilities. Unless otherwise
agreed by the parties, pricing for additional work arising from
such changes shall be at Seller’s time and material rates.
14.3 It shall be acceptable and not considered a change if
Seller delivers a Product that bears a different, superseding
or new part or version number compared to the part or
version number listed in the Contract.

15. Limitations of Liability
15.1 The total liability of Seller for all claims of any kind
arising from or related to the formation, performance or

www.gemotors.com

•

800-541-7191

15.5 If Buyer is supplying Products or Services to a third
party, or using Products or Services at a facility owned by a
third party, Buyer shall either (i) indemnify and defend Seller
from and against any and all claims by, and liability to, any
such third party in excess of the limitations set forth in this
Article 15, or (ii) require that the third party agree, for the
benefit of and enforceable by Seller, to be bound by all the
limitations included in this Article 15.
15.6 For purposes of this Article 15, the term “Seller” means
Seller, its affiliates, subcontractors and suppliers of any tier,
and their respective employees. The limitations in this Article
15 shall apply regardless of whether a claim is based in
contract, warranty, indemnity, tort/extra-contractual liability
(including negligence), strict liability or otherwise, and shall
prevail over any conflicting terms, except to the extent that
such terms further restrict Seller’s liability.

Motor Pricing
Modifications
Pricing
Accessories &
Modifications

15.4 Seller shall not be liable for advice or assistance that
is not required for the work scope under this Contract.

Outline
Dimensions

14.1 Each party may at any time propose changes in the
schedule or scope of Products or Services. Seller is not
obligated to proceed with any change until both parties
agree upon such change in writing. The written change
documentation will describe the changes in scope and
schedule, and the resulting changes in price and other
provisions, as agreed.

15.3 All Seller liability shall end upon expiration of the
applicable warranty period, provided that Buyer may
continue to enforce a claim for which it has given notice
prior to that date by commencing an action or arbitration,
as applicable under this Contract, before expiration of any
statute of limitations or other legal time limitation but in no
event later than one year after expiration of such warranty
period.

Application
Information

14. Changes

15.2 Seller shall not be liable for loss of profit or revenues,
loss of use of equipment or systems, interruption of business,
cost of replacement power, cost of capital, downtime costs,
increased operating costs, any special, consequential,
incidental, indirect, or punitive damages, or claims of Buyer’s
customers for any of the foregoing types of damages.

Other

13.9 Buyer shall indemnify Seller for any and all claims,
damages, losses, and expenses arising out of or relating
to any Hazardous Materials which are or were (i) present
in or about Buyer’s equipment or the Site prior to the
commencement of Seller’s work, (ii) improperly handled
or disposed of by Buyer or Buyer’s employees, agents,
contractors or subcontractors, or (iii) brought, generated,
produced or released on Site by parties other than Seller.

breach of this Contract, or any Products or Services, shall
not exceed the (i) Contract Price, or (ii) if Buyer places
multiple order(s) under the Contract, the price of each
particular order for all claims arising from or related to
that order and ten thousand US dollars (US $10,000) for
all claims not part of any particular order.

16. Governing Law and Dispute Resolution
16.1 This Contract shall be governed by and construed in
accordance with the laws of (i) the State of New York if
Buyer’s place of business is in the U.S. or (ii) England if the
Buyer’s place of business is outside the U.S., in either case
without giving effect to any choice of law rules that would

GEP387M 09/11 • Prices and data subject to change without notice.

6.13

Terms

the hazardous conditions. In such an event, Buyer shall
eliminate the hazardous conditions in accordance with
applicable laws and regulations so that Seller’s work under
the Contract may safely proceed, and Seller shall be entitled
to an equitable adjustment of the price and schedule to
compensate for any increase in Seller’s cost of, or time
required for, performance of any part of the work. Buyer
shall properly store, transport and dispose of all Hazardous
Materials introduced, produced or generated in the course
of Seller’s work at the Site.

General
Information

Form ES 104 (Rev. 4)

Terms and Conditions for Sale of Products and Services

Terms

Other

Application
Information

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Form ES 104 (Rev. 4)

cause the application of laws of any other jurisdiction
(the “Governing Law”). If the Contract includes the sale of
Products and the Buyer is outside the Seller’s country, the
United Nations Convention on Contracts for the International
Sale of Goods shall apply.
16.2 All disputes arising in connection with this Contract,
including any question regarding its existence or validity, shall
be resolved in accordance with this Article 16. If a dispute is
not resolved by negotiations, either party may, by giving
written notice, refer the dispute to a meeting of appropriate
higher management, to be held within twenty (20) business
days after the giving of notice. If the dispute is not resolved
within thirty (30) business days after the giving of notice, or
such later date as may be mutually agreed, either party may
commence arbitration or court proceedings, depending upon
the location of the Buyer, in accordance with the following:
(a) if the Buyer’s pertinent place of business is in the U.S,
legal action shall be commenced in federal court with
jurisdiction applicable to, or state court located in, either
Cobb County, Georgia or the location of Buyer’s principal
place of business; or
(b) if the Buyer’s pertinent place of business is outside the
U.S., the dispute shall be submitted to and finally resolved by
arbitration under the Rules of Arbitration of the International
Chamber of Commerce (“ICC”). The number of arbitrators
shall be one, selected in accordance with the ICC rules,
unless the amount in dispute exceeds the equivalent of U.S.
$5,000,000, in which event it shall be three. When three
arbitrators are involved, each party shall appoint one
arbitrator, and those two shall appoint the third within thirty
(30) days, who shall be the Chairman. The seat, or legal
place, of arbitration, shall be London, England. The arbitration shall be conducted in English. In reaching their decision,
the arbitrators shall give full force and effect to the intent of
the parties as expressed in the Contract, and if a solution is
not found in the Contract, shall apply the governing law of
the Contract. The decision of the arbitrator(s) shall be final
and binding upon both parties, and neither party shall seek
recourse to a law court or other authority to appeal for
revisions of the decision.
16.3 Notwithstanding the foregoing, each party shall have
the right at any time, at its option and where legally available,
to immediately commence an action or proceeding in a
court of competent jurisdiction, subject to the terms of this
Contract, to seek a restraining order, injunction, or similar

6.14

www.gemotors.com

•

800-541-7191

order to enforce the confidentiality provisions set forth in
Article 6 and/or the nuclear use restrictions set forth in
Section 19.1, or to seek interim or conservatory measures.
Monetary damages shall only be available in accordance with
Section 16.2.

17. Inspection and Factory Tests
Seller will apply its normal quality control procedures in
manufacturing Products. Seller shall attempt to accommodate requests by Buyer to witness Seller’s factory tests of
Products, subject to appropriate access restrictions, if such
witnessing can be arranged without delaying the work.

18. Software, Leased Equipment, Remote
Diagnostic Services, PCB Services
If Seller provides any software to Buyer, the Software License
Addendum shall apply. If Seller leases any of Seller’s equipment or provides related Services to Buyer, including placing
Seller’s equipment at Buyer’s site to provide remote Services,
the Lease Addendum shall apply. If Seller provides remote
diagnostic services to Buyer, the Remote Diagnostic Services
Addendum shall apply. If Seller provides PCB Services to
Buyer, the PCB Services Addendum shall apply. If there is any
conflict between these “Terms and Conditions for the Sale of
Products and Services, Form ES 104” and the terms of any
addendum incorporated pursuant to this Article 18, the
terms of the addendum shall take precedence with respect
to the applicable scope.

19. General Clauses
19.1 Products and Services sold by Seller are not intended
for use in connection with any nuclear facility or activity, and
Buyer warrants that it shall not use or permit others to use
Products or Services for such purposes, without the
advance written consent of Seller. If, in breach of this, any
such use occurs, Seller (and its parent, affiliates, suppliers
and subcontractors) disclaims all liability for any nuclear or
other damage, injury or contamination, and, in addition to
any other rights of Seller, Buyer shall indemnify and hold
Seller (and its parent, affiliates, suppliers and subcontractors)
harmless against all such liability. Consent of Seller to any
such use, if any, will be conditioned upon additional terms
and conditions that Seller determines to be acceptable for
protection against nuclear liability.
19.2 Seller may assign or novate its rights and obligations
under the Contract, in whole or in part, to any of its affiliates
or may assign any of its accounts receivable under this

GEP387M 09/11 • Prices and data subject to change without notice.

Terms and Conditions for Sale of Products and Services

19.5 The following Articles shall survive termination or
cancellation of the Contract: 2, 3, 4, 5, 6, 7, 8, 10, 11, 12, 13,
15, 16, 18, 19 and 20.
19.6 The Contract represents the entire agreement between
the parties. No oral or written representation or warranty not
contained in this Contract shall be binding on either party.
Buyer’s and Seller’s rights, remedies and obligations arising
from or related to Products and Services sold under this
Contract are limited to the rights, remedies and obligations
stated in this Contract. No modification, amendment,
rescission or waiver shall be binding on either party unless
agreed in writing.

20.3 If Buyer is an agency of the U.S. Government, then as
permitted by FAR 12.302, Buyer agrees that all paragraphs of
FAR 52.212-4 (except those listed in 12.302(b)) are replaced
with these Terms and Conditions. Buyer further agrees the
subparagraphs of FAR 52.212-5 apply only to the extent
applicable for sale of COTS and/or commercial items and as
appropriate for the Contract Price.
20.4 If Buyer is procuring the Products or Services as a
contractor, or subcontractor at any tier, on behalf of any
agency of the U.S. Government, then Buyer agrees that FAR
52.212-5(e) or 52.244-6 (whichever is applicable) applies only
to the extent applicable for sale of COTS and/or commercial
items and as appropriate for the Contract Price.

Motor Pricing
Other

19.7 Except as provided in Article 15 (Limitations of Liability)
and in Section 19.1 (no nuclear use), this Contract is only for
the benefit of the parties, and no third party shall have a
right to enforce any provision of this Contract, whether
under the English Contracts (Rights of Third Parties) Act of
1999 or otherwise.

Modifications
Pricing

20.2 Buyer agrees that all Products and Services provided
by Seller meet the definition of “commercial-off-the-shelf”
(“COTS”) or “commercial item” as those terms are defined in
Federal Acquisition Regulation (“FAR”) 2.101. To the extent
the Buy American Act, Trade Agreements Act, or other
domestic preference requirements are applicable to this
Contract, the country of origin of Products is unknown
unless otherwise specifically stated by Seller in this Contract.
Buyer agrees any Services offered by Seller are exempt from
the Service Contract Act of 1965 (FAR 52.222-41). Buyer
represents and agrees that this Contract is not funded in
whole or in part by American Recovery Reinvestment Act
funds unless otherwise specifically stated in the Contract.
The version of any applicable FAR clause listed in this Article
20 shall be the one in effect on the effective date of this
Contract.

Accessories &
Modifications

19.4 If any Contract provision is found to be void or
unenforceable, the remainder of the Contract shall not be
affected. The parties will endeavor to replace any such void
or unenforceable provision with a new provision that
achieves substantially the same practical and economic
effect and is valid and enforceable.

20.1 This Article 20 applies only if the Contract is for the
direct or indirect sale to any agency of the U.S. government
and/or is funded in whole or in part by any agency of the
U.S. government.

Outline
Dimensions

19.3 Buyer shall notify Seller immediately upon any change
in ownership of more than fifty percent (50%) of Buyer's
voting rights or of any controlling interest in Buyer. If
Buyer fails to do so or Seller objects to the change, Seller
may (a) terminate the Contract, (b) require Buyer to provide
adequate assurance of performance (including but not
limited to payment), and/or (c) put in place special controls
regarding Seller’s Confidential Information.

20. US Government Contracts

Application
Information

Contract to any party without Buyer’s consent. Buyer agrees
to execute any documents that may be necessary to
complete Seller’s assignment or novation. Seller may
subcontract portions of the work, so long as Seller remains
responsible for it. The delegation or assignment by Buyer of
any or all of its rights or obligations under the Contract
without Seller’s prior written consent (which consent shall
not be unreasonably withheld) shall be void.

General
Information

Form ES 104 (Rev. 4)

Terms

19.8 This Contract may be signed in multiple counterparts
that together shall constitute one agreement.

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

6.15

Notes

Terms

Other

Application

Outline
Dimensions

Accessories &
Modifications

Modifications
Pricing

Motor Pricing

General
Information

Other Information

6.16

www.gemotors.com

•

800-541-7191

GEP387M 09/11 • Prices and data subject to change without notice.

Additional Motor Resources
www.gemotors.com

Visit GE Motors online for additional information regarding the
entire product line of GE Motors. For more information on the
following and more, check out our motors’ homepage.
•	 Motors	Overview
•	 Authorized	Service	Centers
•	 Parts	Distributors
•	 Contact	Information
•	 Application	Details
•	 Product	Line	Literature

GE
Fort Wayne, IN 46802
www.gemotors.com
© 2012 General Electric Company.
All rights reserved.

GEP387M 1/12



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2012:01:04 10:57:05-05:00
Creator                         : Adobe InDesign CS5 (7.0.4)
Modify Date                     : 2013:02:14 08:02:28-05:00
Trapped                         : False
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2013:02:14 08:02:28-05:00
Creator Tool                    : Adobe InDesign CS5 (7.0.4)
Format                          : application/pdf
Document ID                     : uuid:a318a656-f9d1-9149-b66d-5b4871be1921
Instance ID                     : uuid:dbc5a10d-6027-4f6d-a488-903cddd37306
Producer                        : Adobe PDF Library 9.9
Page Count                      : 180

EXIF Metadata provided by EXIF.tools