GemTek Technology CISCO867VAE XDSL Router User Manual HIG880 860

Download:
Mirror Download [FCC.gov]
Document ID	1959035
Application ID	cNupggyZrSV0otHjFpv63g==
Document Description	User Manual Part 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	303.74kB (3796728 bits)
Date Submitted	2013-05-07 00:00:00
Date Available	2013-11-03 00:00:00
Creation Date	2013-05-03 17:53:59
Producing Software	Acrobat Distiller 10.1.5 (Windows)
Document Lastmod	2013-05-03 17:54:31
Document Title	HIG880-860.book
Document Creator	FrameMaker 7.2
Document Author:	panilkum

Cisco 860 Series, Cisco 880 Series, and
Cisco 890 Series Integrated Services
Routers Hardware Installation Guide
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Last Revised: March 6, 2013
Text Part Number: OL-16215-10
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the
document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
© 2012 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
vii
Objective
vii
Audience
vii
Organization
viii
Conventions
viii
Related Documentation
xv
Searching Cisco Documents
xvi
Obtaining Documentation and Submitting a Service Request
CHAPTER
Product Overview
xvi
1-1
General Description
Cisco 860 Series ISRs
1-2
1-2
Cisco 860VAE Series ISRs
Interfaces 1-3
IOS Images 1-4
1-3
Cisco 880 Series ISRs 1-6
Cisco 880 Series Data Routers 1-6
Cisco 880 Series Voice and Data Routers 1-9
Cisco 881 SRST and Cisco 888 SRST 1-9
Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W 1-13
Cisco 880 Series with Embedded WLAN Antennas 1-15
Cisco 887VA-WD 1-15
C881WD 1-16
Cisco 890 Series ISRs 1-17
Cisco 891, Cisco 892, and Cisco 892F 1-17
Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA
1-20
Hardware Features 1-27
Kensington Lock 1-27
Reset Button 1-27
Cisco 860VAE Routers—Custom Configuration File 1-27
Custom Configuration File for Cisco 892FSP, 896VA, 897VA, and Cisco 898EA 1-28
LEDs 1-30
Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Data Routers 1-35
Memory 1-36
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
iii
Contents
USB Port 1-37
Fan 1-37
Power Supply 1-38
Power over Ethernet Module 1-38
3G Cellular Data WAN Connectivity 1-38
Wireless LAN Connectivity 1-39
Supported Cisco Radio Antennas 1-40
Small Form-Factor Pluggable Port 1-40
Feature Summary 1-41
CHAPTER
Installing the Router
2-1
Equipment, Tools, and Connections 2-2
Items Shipped with your Router 2-2
Additional Items 2-2
Connections 2-3
Ethernet Devices 2-3
Installing the Router 2-3
Warnings 2-4
Installing Antennas 2-4
Installing on a Table 2-7
Mounting on a Wall 2-8
Installing in a Rack 2-11
Installing the Router Ground Connection
Installing the FIPS Cover 2-14
CHAPTER
Connecting the Router
Safety Warnings
3-1
3-2
Preparing to Connect the Router 3-4
Preventing Damage to the Router
3-4
Connecting a PC, Server, or Workstation
Connecting a Phone
2-13
3-5
3-6
Connecting an External Ethernet Switch
Connecting the V.92 modem Port
3-7
3-8
Connecting a Terminal or PC to the Console Port
Terminal Emulator Settings 3-10
Connecting a Modem to the Auxiliary Port
Connecting the 3G Card
3-9
3-10
3-11
Installing the 3G Adapter for Extended Cable/Antenna
3-17
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
iv
OL-16215-10
Contents
Connecting a Data BRI Port
3-21
Connecting an FE Line to an FE WAN Port
3-23
Connecting a GE Line to an GE WAN Port
3-24
Connecting an xDSL Line
3-25
Connecting Power over Ethernet
Connecting the AC Adapter
3-27
3-28
Connecting an FXS Line
3-32
Connecting an FXO Line
3-34
Connecting a Voice ISDN BRI Line
3-35
Connecting a Small Form-Factor Pluggable Module
Safety Warnings 3-37
Installing an SFP Module 3-38
Removing an SFP Module 3-38
Online Insertion and Removal 3-39
Verifying Connections
CHAPTER
Initial Configuration
3-40
4-1
Cisco Configuration Professional Express
Cisco IOS CLI
4-1
4-1
Setup Command Facility
4-3
Verifying the Initial Configuration
4-5
Initial Configuration of the Wireless Access Point
APPENDIX
3-37
Technical Specifications
Router Specifications
4-6
A-1
A-2
Wireless Access Point
A-3
FE and GE Port Pinouts
A-3
Console and Auxiliary Port Connector Pinouts
FXS and FXO Port Connector Pinouts
VDSL2 Port Connector Pinouts
A-5
A-5
ADSL2+ Port Connector Pinouts
V.92 Port Connector Pinouts
A-4
A-5
A-6
G.SHDSL Port Connector Pinouts
A-6
Data BRI Port Connector Pinouts
A-7
Voice ISDN BRI Interface Pin Numbers and Functions
SFP Port Connector Pinouts
A-7
A-8
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
Contents
Cable Specifications A-8
Ethernet Cable Specifications A-9
Maximum Cable Length A-9
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
vi
OL-16215-10
Preface
This preface describes the objectives, audience, organization, and conventions of this guide, and
describes related documents that have additional information. It contains the following sections:
•
Objective, page vii
•
Audience, page vii
•
Organization, page viii
•
Conventions, page viii
•
Related Documentation, page xv
•
Searching Cisco Documents, page xvi
•
Obtaining Documentation and Submitting a Service Request, page xvi
Objective
This guide provides an overview and explains how to install, connect, and perform initial configuration
for the wireless and nonwireless Cisco 860 series, Cisco 880 series, and Cisco 890 series Integrated
Services Routers (ISRs). Some information may not apply to your particular router model.
For warranty, service, and support information, see the “Cisco One-Year Limited Hardware Warranty
Terms” section in Readme First for the Cisco 800 Series Integrated Services Routers that was shipped
with your router.
Audience
This guide is intended for Cisco equipment providers who are technically knowledgeable and familiar
with Cisco routers and Cisco IOS software and features.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
vii
Preface
Organization
This guide is organized into the following chapters and appendix.
Chapter
Name
Description
Chapter 1
Chapter 1, “Product Overview”
Describes the router models and the
hardware features available.
Chapter 2
Chapter 2, “Installing the Router”
Lists the items shipped with the router, the
equipment and tools necessary for
installing the router, the safety warnings
and guidelines, and the procedures for
installing the router.
Chapter 3
Chapter 3, “Connecting the Router”
Describes typical connections for the
router, procedures for connecting the
router to various devices, and how to
verify the connections.
Chapter 4
Chapter 4, “Initial Configuration”
Provides the procedures for initially
configuring the router settings.
Appendix A
Appendix A, “Technical Specifications” Provides the router, port, and cabling
specifications.
Conventions
This section describes the conventions used in this guide.
Note
Caution
Tip
Means reader take note. Notes contain helpful suggestions or references to additional information and
material.
This symbol means reader be careful. In this situation, you might do something that could result in
equipment damage or loss of data.
Means the following information will help you solve a problem. The tip information might not be
troubleshooting or even an action, but could be useful information.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
viii
OL-16215-10
Preface
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
Varoitus
TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
ix
Preface
Avvertenza
IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel
VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia!
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning!
VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
Preface
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
xi
Preface
Aviso
INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel
VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
xii
OL-16215-10
Preface
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
xiii
Preface
Warning
When installing the product, please use the provided or designated connection cables/power
cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical
Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown
on the code) for any other electrical devices than products designated by CISCO. The use of cables
that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the
code) is not limited to CISCO-designated products. Statement 371
Warning
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions. Statement 1015
Warning
Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool. Statement 1035
Warning
Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations. Statement 1036
Warning
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface. Statement 1037
Warning
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning. Statement 1038
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
xiv
OL-16215-10
Preface
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Read the installation instructions before connecting the system to the power source. Statement 1004
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Related Documentation
In addition to the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR Hardware Installation
Guide (this document), the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR documentation
set includes the following documents:
•
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
•
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software
Configuration Guide
•
Software Activation on Cisco Integrated Services Routers and Cisco Integrated Service Routers G2
•
Cisco IOS Software Activation Configuration Guide
•
Declarations of Conformity and Regulatory Information for Cisco Access Products with 802.11a/b/g
and 802.11b/g Radios
•
Cisco IOS Release Notes
•
Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T
•
Cisco IOS Security Configuration Guide, Release 12.4T
•
Cisco IOS Security Command Reference, Release 12.4T
•
Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges, versions 12.4(10b) JA
and 12.3(8) JEC
•
Wireless LAN Controllers
•
Unified Wireless LAN Access Points
•
Cisco IOS Voice Port Configuration Guide
•
SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways
•
Cisco CP Express User’s Guide
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
xv
Preface
Searching Cisco Documents
To search a HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most
browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward
is also available.
To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader
Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document.
Use the Full Reader Search window to search multiple PDF files simultaneously and to change case
sensitivity and other options. Adobe Reader’s online help has more information about how to search PDF
documents.
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as an RSS feed and set content to be
delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently
supports RSS Version 2.0.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
xvi
OL-16215-10
CH A P T E R
Product Overview
This chapter provides an overview of the features available for the Cisco 860 series, Cisco 880 series,
and Cisco 890 series Integrated Services Routers (ISRs), and contains the following sections:
•
General Description, page 1-2
•
Cisco 860 Series ISRs, page 1-2
•
Cisco 860VAE Series ISRs, page 1-3
•
Cisco 880 Series ISRs, page 1-6
•
Cisco 890 Series ISRs, page 1-17
•
Hardware Features, page 1-27
Note
For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap
that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and
SOHO Series Routers.
Note
Some illustrations in this document show a wireless router. Both wireless and nonwireless models are
available in the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs. Port and feature locations
are similar for both wireless and nonwireless routers.
Note
Throughout this document the term VDSL refers to support for VDSL2 (ITU G.993.2) and ADSL refers
to support for ADSL, ADSL2, & ADSL2+ (ITU G.992.1, G.992.3, & G.992.5).
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-1
Chapter 1
Product Overview
General Description
General Description
The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs provide data, voice, Wi-Fi
CERTIFIED™ wireless access point (AP), integrated Virtual Private Network (VPN), and backup
capabilities to corporate teleworkers and to remote and small offices with fewer than 20 users. These
routers are capable of bridging and multiprotocol routing between LAN and WAN ports. The routers
provide advanced features, such as high speed DSL (G.SHDSL, ADSL, or VDSL), 802.11n, quality of
service (QoS), firewall, antivirus protection, and Secure Socket Layer (SSL). The Cisco 860VAE, 886VA
and 887VA series routers have the additional capability of DSL Multi-mode (VDSL/ADSL).
The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs have a desktop form factor with
built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. These
ISRs are powered by an external power supply adapter. The various models differ in the WAN interface
and features that they support.
Cisco 860 Series ISRs
The Cisco 860 series ISRs are fixed-configuration data routers that support the following features:
•
An integrated 4-port 10/100 Ethernet switch for connecting to the LAN
•
A10/100 Fast Ethernet (FE) port for connecting to the WAN.
•
Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP
Figure 1-1 shows the front panel details of the Cisco 860 wireless router.
Front Panel of the Cisco 860 Series Wireless ISR
231969
Figure 1-1
LEDs
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-2
OL-16215-10
Chapter 1
Product Overview
Cisco 860VAE Series ISRs
Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do
not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series
routers.
Figure 1-2
Back Panel of the Cisco 861W ISR
Cisco 861W
232181
WAN
FE 4
Primary WAN port—10/100
Reset button
Antenna—captive omnidirectional dipole
WLAN antenna (wireless models only)
Power connector
4-port 10/100 Ethernet switch
Earth ground connection
Serial port—console or auxiliary
Kensington security slot
Cisco 860VAE Series ISRs
The Cisco 860VAE series ISRs are fixed-configuration data routers. This section describes the features
of the products in this series.
Interfaces
Table 1-1 describes the interfaces of the Cisco 860VAE series routers.
Table 1-1
Interfaces of the Cisco 860VAE Series ISRs
Model
Interfaces
866VAE
867VAE
866VAE-K9
867VAE-K9
1 GE switch port
—
—
1 GE WAN port
4 FE switch ports
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-3
Chapter 1
Product Overview
Cisco 860VAE Series ISRs
Table 1-1
Interfaces of the Cisco 860VAE Series ISRs (continued)
Model
Interfaces
866VAE
867VAE
866VAE-K9
867VAE-K9
1 VDSL/ADSL over POTS port
—
—
1 VDSL/ADSL over ISDN port
—
—
1. FE = Fast Ethernet
2. GE = Gigabit Ethernet
Note
The Cisco 866VAE, 867VAE, 866VAE-K9, and 867VAE-K9 routers each have two WAN ports. Only one
of the two ports can be active at any given time.
IOS Images
Table 1-2 describes the IOS images included in Cisco 860VAE series routers.
Table 1-2
IOS Images of the Cisco 860VAE Series ISRs
Model
IOS Image
866VAE
867VAE
866VAE-K9
867VAE-K9
c860vae-ipbasek9-mz
—
—
c860vae-advsecurityk9-mz
—
—
c860vae-advsecurityk9_npe-mz
—
—
Figure 1-3 shows the front panel details of the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and
Cisco 867VAE-K9 integrated services routers (ISRs).
Figure 1-3
Front Panel of the Cisco 860VAE series ISR
246199
Cisco 860 Series
LEDs
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-4
OL-16215-10
Chapter 1
Product Overview
Cisco 860VAE Series ISRs
Figure 1-4 shows the back panel details of the Cisco 866VAE ISR.
Figure 1-4
Back Panel of the Cisco 866VAE ISR
Cisco 866VAE
VDSL/ADSL
WAN
OVER ISDN
GE0
LAN
CONSOLE
12V
2.5A
RESET
FE 2
FE 1
FE 0
AUX
246200
FE 3
xDSL port1
On/Off switch
GE WAN interface
Power connector
Ethernet LAN FE interfaces (FE0 through
FE3 interfaces)
Reset button
USB port
Kensington security slot
Serial port—console or auxiliary
1. Using RJ-11.
Figure 1-5 shows the back panel details of the Cisco 867VAE-K9.
Figure 1-5
Back Panel of the Cisco 867VAE-K9 ISR
Cisco 867VAE-K9
VDSL/ADSL
WAN
CONSOLE
LAN
12V
2.5A
RESET
GE1
GE0
FE3
FE2
FE1
AUX
FE0
284558
OVER POTS
xDSL port
On/Off switch
GE WAN interface
Power connector
Ethernet LAN GE and FE interfaces (GE0
interface and FE0 through FE3 interfaces)
Reset button
USB port
Kensington security slot
Serial port—console or auxiliary
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-5
Chapter 1
Product Overview
Cisco 880 Series ISRs
Cisco 880 Series ISRs
The Cisco 880 series ISRs have data and voice capabilities. They have the following features:
•
Integrated 4-port 10/100 Ethernet switch for connecting to the LAN
•
10/100 FE, VDSLoPOTS, ADSL over POTS, ADSL over ISDN, DSL Multi-mode
(VDSL/ADSLoPOTS, VDSL/ADSLoISDN Cisco VA models only), or G.SHDSL port for
connecting to the WAN
•
Optional embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP
•
Optional 2-port Power over Ethernet (PoE)
Note
•
The Cisco 880 series ISRs can include an optional PoE module that provides power to
802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not
configured with the factory order, you must order and install it to enable the PoE function.
DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB
system memory
The following features are located on the front panel:
•
USB 1.1 port
•
Express card slot for third-generation (3G) cellular data WAN connectivity, available only on the
Cisco 880G models
This section contains the following topics:
•
Cisco 880 Series Data Routers, page 1-6
•
Cisco 880 Series Voice and Data Routers, page 1-9
•
Cisco 880 Series with Embedded WLAN Antennas, page 1-15
Cisco 880 Series Data Routers
The Cisco 880 series data routers provide integrated VPN, embedded Wi-Fi CERTIFIED™,
802.11b/g/n-compliant wireless AP, 3G, and backup capabilities. Figure 1-6 through Figure 1-9 show
the features available on Cisco 880 series data routers. Some of the features shown may not be available
on your router.
Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, VDSL/ADSL
over ISDN, VDSL/ADSL over POTS, or 10/100 FE. See the Cisco 880 Series Integrated Services
Routers data sheet for the WAN interface that is supported on your router.
Figure 1-6 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G
card slot are located on the front panel.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-6
OL-16215-10
Chapter 1
Product Overview
Cisco 880 Series ISRs
Front Panel of the Cisco 880 Series Wireless Data Router
231950
Figure 1-6
LEDs
3G express card slot—Supports third-party
3G card (Cisco 880G models only)
USB port
1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors.
Figure 1-7 shows the back panel details of the Cisco 886VA data router.
Back Panel of the Cisco 886VA Router
254090
Figure 1-7
Data BRI1 0
Reset button
Primary WAN port—VDSL/ADSL over
ISDN
Power connector
4-port 10/100 Ethernet switch2
Earth ground connection
Serial port—console or auxiliary
Kensington security slot
PoE power connector—optional
1. BRI = Basic rate interface.
2. Ports 0 and 1 provide PoE with the optional PoE module installed.
Caution
The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN
port may occur if a non-RJ-45 connector is inserted.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-7
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-8 shows the back panel details of the Cisco 887VA and 886VA-M data router.
Back Panel of the Cisco 887VA and 887VA-M Router
254139
Figure 1-8
Primary WAN port—VDSL/ADSL over
POTS1
Reset button
4-port 10/100 Ethernet switch2
Power connector
Serial port—console or auxiliary
Earth ground connection
PoE power connector—optional
Kensington security slot
1. 887VA-M has Annex M support.
2. Ports 0 and 1 provide PoE with the optional PoE module installed.
Caution
For the Cisco 887VA, the primary WAN port is designed for an RJ-45 connector only. Damage
to the primary WAN port may occur if a non-RJ-45 connector is inserted.
Figure 1-9 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have
antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data
routers.
Back Panel of the Cisco 888W Data Router
231951
Figure 1-9
10
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-8
OL-16215-10
Chapter 1
Product Overview
Cisco 880 Series ISRs
ISDN port—not available on 3G models
PoE power connector for optional PoE
module1
Primary WAN port2—G.SHDSL,
VDSLoPOTS, ADSLoPOTS, ADSLoISDN,
or 10/100 FE
Reset button
Antenna—captive omnidirectional dipole
WLAN antenna (wireless models only)
Power connector
4-port 10/100 Ethernet switch
Earth ground connection
Serial port—console or auxiliary
10 Kensington security slot
1. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install it to enable the
PoE function.
2. Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, or 10/100 FE. The VDSLoPOTS
port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See Figure 1-2
for the location of the 10/100 FE WAN port.
Cisco 880 Series Voice and Data Routers
The Cisco 880 series voice and data routers provide both voice and data ports. The voice ports managed
voice services that interface with Foreign Exchange Station (FXS), Foreign Exchange Office (FXO), or
BRI connections.
Cisco 881 SRST and Cisco 888 SRST
Figure 1-10, Figure 1-11, and Figure 1-12 show the features available on the Cisco 881 SRST and
Cisco 888 SRST routers. The features available vary, depending on the router model. Some features may
not be available on your router.
Depending on the router model, the primary WAN port can be either G.SHDSL or 10/100 FE. See the
Cisco 880 Series Integrated Services Routers data sheet for the WAN interface and voice ports that are
supported on your router.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-9
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-10 shows the front panel details of the Cisco 881 SRST and Cisco 888 SRST wireless voice
router.
Front Panel of the Cisco 881 SRST and Cisco 888 SRST Wireless Voice Router
270495
Figure 1-10
LEDs
USB port
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-10
OL-16215-10
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-11 shows the back panel details of the Cisco 881SRST-W voice router.
Back Panel of the Cisco C881SRST-W Voice Router
241904
Figure 1-11
10
Primary WAN port1—10/100 FE
Antenna—captive wireless omnidirectional
dipole WLAN antenna (wireless models only)
Voice ports—four FXS2/DID3 ports, one
FXO4 port with TBP5 power failover
Reset button
4-port 10/100 Ethernet switch6
Power connector
Serial port—console or auxiliary
Earth ground connection
PoE power connector for optional PoE
module7
10 Kensington security slot
1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
2. FXS = Foreign Exchange Station.
3. DID = Direct Inward Dialing.
4. FXO = Foreign Exchange Office.
5. TBP = trunk bypass.
6. Ports 0 and 1 provide PoE with the optional PoE module installed.
7. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
to ethernet ports 0 and 1. If this feature was not configured with the factory order, SKU 800-IL-PM-2, you must order and
install it to enable the PoE function. The PoE power supply, SKU 800-ILPM-4, is also required.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-11
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-12 shows the back panel details of the Cisco 888SRST-W voice router.
Back Panel of the Cisco C888SRST-W Voice Router
241905
Figure 1-12
10
Primary WAN port1—G.SHDSL
Antenna—captive wireless omnidirectional
dipole WLAN antenna (wireless models only)
Voice ports—four FXS/DIDports and one
voice BRI port
Reset button
4-port 10/100 Ethernet switch2
Power connector
Serial port—console or auxiliary
Earth ground connection
PoE power connector for optional PoE
module3
10 Kensington security slot
1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.
2. Ports 0 and 1 provide PoE with the optional PoE module installed.
3. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
to ethernet ports 0 and 1. If this feature was not configured with the factory order, SKU 800-IL-PM-2, you must order and
install it to enable the PoE function. The PoE power supply, SKU 800-ILPM-4, is also required.
Caution
The primary WAN port on all 888E models is designed for an RJ-45 connector only. Damage
to the primary WAN port may occur if a non-RJ-45 connector is inserted.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-12
OL-16215-10
Chapter 1
Product Overview
Cisco 880 Series ISRs
Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W
Figure 1-13, Figure 1-14, and Figure 1-15 show the features available on the Cisco 881-V and
Cisco 887VA-V routers. The features available vary, depending on the router model. Some features may
not be available on your router.
The Cisco 881-V and Cisco 887VA-V voice and data series gives you the flexibility to use either FXS
or BRI voice ports. However, the number of concurrent calls that can be supported by the router is limited
by the codec complexity setting on the router. Table 1-3 lists the maximum number of calls that is
supported when the codec complexity command is configured for Flexible, Medium or High complexity.
Note
Configuring the codec complexity setting to support secure calls uses DSP resources, but does not affect
the maximum number of supported calls.
Table 1-3
Maximum Number of Supported Calls
Flexible Complexity
Medium Complexity
High Complexity
C881-V
C887VA-V
C887VA-V-W
Figure 1-13 shows the front panel details of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W.
Front Panel of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W Routers
246861
Figure 1-13
LEDs
USB port
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-13
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-14 shows the back panel for the Cisco 887VA-V-W router. The Cisco 887VA-V (non-wireless)
router does not have the antennas on the back panel.
Figure 1-14
Back Panel of the Cisco 887 VA-V Router
11
VD SL/A D SL
246864
overPO TS
C 887VA -W VO IC E
10
Data BRI
Reset Button
Voice BRI
Power connector
Voice ports—four FXS/DID ports
Earth ground connection
Fast Ethernet LAN—four ports
10 Kensington security slot
Console Port
11 Primary WAN port—VDSL/ADSL over
POTS
PoE power connector (optional)
Figure 1-15 shows the back panel for the Cisco 881-V router.
Figure 1-15
Back Panel of the Cisco 881-V Router
246866
C881 VOICE
10
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-14
OL-16215-10
Chapter 1
Product Overview
Cisco 880 Series ISRs
Fast Ethernet WAN port
PoE power connector (optional)
Voice BRI ports
Reset button
Voice ports—four FXS/DID ports and one
FXO port.
Power connector
Fast Ethernet LAN—four ports
Earth ground connection
Console Port
10 Kensington security slot
Cisco 880 Series with Embedded WLAN Antennas
Some Cisco 880W, 880WD, and 880-WD ISRs have three embedded WLAN antennas.
These ISRs are fixed-platform routers that:
•
Provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, and
backup capabilities.
•
Use single-band (2.4 GHz) WLAN cards or dual-band (2.4 GHz and 5 GHz) WLAN cards.
•
Require a single external power supply: a 30-W power supply for non-POE-enabled routers or a
60-W power supply for POE-enabled routers.
•
Have a fixed 512 MB of system memory.
For information on configuring the Cisco 880 series ISRs, see Cisco 880 Series Integrated Services
Router Software Configuration Guide.
Cisco 887VA-WD
Figure 1-16 shows the front panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs. The
front panel has LEDs only. All the ports are in the back panel.
Figure 1-16
Front Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs
OK
PPP
POE
CD DATA
LINK 2.4GHz 5GHz
xDSL
WLAN
Cisco 800 Series
VPN
284983
FE LAN
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-15
Chapter 1
Product Overview
Cisco 880 Series ISRs
Figure 1-17 shows the back panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs.
Back Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs
overPOTS
overPOTS
Cisco
Cisco 887VA-WD
887VA-WD
33
22
CONSOLE
CONSOLE
FE LAN
FE LAN
11
00
AUX
AUX
POE OPTION
POE OPTION
REQUIRES 5A
REQUIRES 5A
POWER
POWER
ADAPTOR
ADAPTOR RESET
RESET
4 5
USB port
Power connector
4-port 10/100 Ethernet switch
Kensington security slot
Serial port—console or auxiliary
Power switch
Note
Reset button
No separate PoE power supply is
required for routers with embedded
WLAN antennas. For information on
system power supply requirements
when PoE is enabled, see the “Power
over Ethernet Module” section on
page 1-38.
12VDC
12VDC
284988
284988
Figure 1-17
5A
5A
VDSL/ADSL port
C881WD
Figure 1-18 shows the front panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs. The front
panel has LEDs only. All the ports are in the back panel.
Figure 1-18
Front Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs
OK
PPP
POE
FE4
LINK 2.4GHz 5GHz
WAN
WLAN
Cisco 800 Series
VPN
284982
FE LAN
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-16
OL-16215-10
Chapter 1
Product Overview
Cisco 890 Series ISRs
Figure 1-19 shows the back panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs.
Figure 1-19
Back Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs
Cisco 881WD
POE OPTION
REQUIRES 5A
POWER
ADAPTOR
RESET
12VDC
AUX
284987
CONSOLE
FE LAN
FE WAN
Primary WAN port—10/100 FE
Reset button
USB port
Power connector
4-port 10/100 Ethernet switch
Kensington security slot
Serial port—console or auxiliary
Power switch
Note
5A
No separate PoE power supply is
required for routers with embedded
WLAN antennas. For information on
system power supply requirements
when PoE is enabled, see the “Power
over Ethernet Module” section on
page 1-38.
Cisco 890 Series ISRs
Cisco 891, Cisco 892, and Cisco 892F
The Cisco 891, Cisco 892, and Cisco 892F ISRs have the following features:
•
Integrated 8-port 10/100 Ethernet switch for connecting to the LAN
•
10/100 FE and 10/100/1000 Gigabit Ethernet (GE) port for connecting to the WAN
•
Separate console and auxiliary ports
•
Optional embedded Wi-Fi CERTIFIED™ dual radio 802.11a/b/g/n-compliant wireless AP
•
Optional 4-port PoE
Note
•
The Cisco 890 series ISRs can include an optional PoE module that provides power to
802.3af-compliant devices connected to ethernet ports 0 through 3. If this feature was not
configured with the factory order, you must order and install it to enable the PoE function.
Security feature card (SFC) socket
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-17
Chapter 1
Product Overview
Cisco 890 Series ISRs
•
DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB
system memory in Cisco 891 and 892 series ISRs, and a total of 1 GB system memory in
Cisco 892F series ISRs
•
Three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel for
non-captive dual-band WLAN antenna (wireless models only)
•
Support for the AIM2-CUE-K9 and AIM2-APPRE-104-K9
•
GE small-form-factor pluggable (SFP) port (Cisco 892F series ISRs only)
The following feature is located on the front panel:
•
Two USB 2.0 ports
Figure 1-20 shows the front panel details of the Cisco 890 wireless router.
Front Panel of the Cisco 890 Series Wireless ISR
272367
Figure 1-20
LEDs
USB ports
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-18
OL-16215-10
Chapter 1
Product Overview
Cisco 890 Series ISRs
Figure 1-21 shows the back panel details of the Cisco 892-W router. Nonwireless routers do not have
RP-TNC antennas or connectors on the back panel. Some of the features that are shown may not be
available on your router. However, the feature locations are similar across all Cisco 890 series routers.
Back Panel of the Cisco 892-W Router
272369
Figure 1-21
10 11
Antenna—dipole swivel antenna attached to
RP-TNC connectors (wireless models only)
PoE power connector for optional PoE
module1
Backup—Data BRI2 or V.923 port
Reset button
Primary WAN port—FE and GE
Power connector
Auxiliary port
10 Earth ground connection
Console port
11 Kensington security slot
8-port 10/100 Ethernet switch
1. The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected
to ethernet ports 0 through 3. If this feature was not configured with the factory order you must order and install it to enable
the PoE function.
2. The Data BRI port is available only on the Cisco 892 router models.
3. The V.92 port (not shown) is available only on the Cisco 891 router models and is located between the console port and the
Ethernet switch.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-19
Chapter 1
Product Overview
Cisco 890 Series ISRs
Figure 1-22 shows the location of the SFP port in a Cisco 892F-W router.
Figure 1-22
SFP Port Location in a Cisco 892F-W Router
Cisco 892F-W
SFP
278179
EN
SFP port
SFP LEDs
Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA
The Cisco 892FSP, 896VA, 897VA (897VA, 897VAM, 897VAW, 897VAMW), and 898EA routers have
the following features:
Note
•
Integrated 8-port 10/100/1000 Gigabit Ethernet(GE) switch for connecting to the LAN
•
Two 10/100/1000 GE ports for the Cisco 892FSP
•
One 10/100/1000 GE port for the Cisco 896VA, 897VA, and the Cisco 898EA. Either the SFP socket
or the 10/100/1000 GE port can be active at a given time, but not both.
•
Single console and auxiliary ports for configuration and management
•
512 MB of on-board memory (upgrade option to 1 GB)
•
256 MB flash memory for the Cisco 896VA, 897VA, and Cisco 898EA
•
One USB 2.0 port
•
Optional internal adapter for inline PoE on 4 switch ports for IP phones or external wireless access
points for Cisco 896VA, 897VA, and 898EA models only. No PoE support on Cisco 892FSP.
The Cisco 892FSP does not support AIM2-CUE-K9 and AIM2-APPRE-104-K9 because it does not have
an SFC socket.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-20
OL-16215-10
Chapter 1
Product Overview
Cisco 890 Series ISRs
Figure 1-23 shows the back panel of the Cisco 892FSP router.
Figure 1-23
Back Panel of the Cisco 892FSP Router
C isco 892FSP
C O N SO LE
GE W AN
GE W AN
284781
SFP
RESE T
AU X
12VD C
2.5A
GE WAN interface
Power connector
SFP port
On/Off switch
USB port
Reset button
8-port Gigabit Ethernet switch
Earth ground connection
Console / Auxiliary port
10 Kensington security slot
10
Figure 1-24 shows the front panel of the Cisco 892FSP router.
Front Panel of the Cisco 892FSP Router
284782
Figure 1-24
LEDs
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-21
Chapter 1
Product Overview
Cisco 890 Series ISRs
Figure 1-25 shows the back panel of the Cisco 896VA router.
Figure 1-25
Back Panel of the Cisco 896VA Router
12
VDSL/ADSL
overISDN
GE WAN
GELAN 5
Cisco 896VA
CONSOLE
POE
54VDC
12VDC
ISDN
Power connector
GE WAN interface
On/Off switch
SFP port
Reset button
USB port
RESET
1.2A
2.5A
344766
ISDN
10 11
10 Earth ground connection
8-port Gigabit Ethernet switch
Console / Auxiliary port
11 Kensington security slot
12 VDSL / ADSL over ISDN
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
Figure 1-26 shows the front panel of the Cisco 896VA and the Cisco 897VA router.
Front Panel of the Cisco 896VA and Cisco 897VA Router
344765
Figure 1-26
LEDs
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-22
OL-16215-10
Chapter 1
Product Overview
Cisco 890 Series ISRs
Figure 1-27 shows the back panel of the Cisco 897VA router.
Figure 1-27
Back Panel of the Cisco 897VA Router
12
VDSL/ADSL
overPOTS
GE WAN
GELAN 5
Cisco 897VA
CONSOLE
POE
54VDC
12VDC
ISDN
Power connector
GE WAN interface
On/Off switch
SFP port
Reset button
USB port
RESET
1.2A
2.5A
344767
ISDN
10 11
10 Earth ground connection
8-port Gigabit Ethernet switch
Console / Auxiliary port
11 Kensington security slot
12 VDSL / ADSL over POTS
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
Figure 1-28 shows the back panel of the Cisco 897VAM router.
Figure 1-28
Back Panel of the Cisco 897VAM Router
11
VDSL/ADSL
overPOTS
GELAN 5
POE
54VDC
12VDC
344769
CONSOLE
GE WAN
RESET
1.2A
2.5A
GE WAN interface
On/Off switch
SFP port
Reset button
USB port
Earth ground connection
10
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-23
Chapter 1
Product Overview
Cisco 890 Series ISRs
8-port Gigabit Ethernet switch1
10 Kensington security slot
Console / Auxiliary port
11 VDSL / ADSL over POTS
Power connector
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
Figure 1-29 shows the front panel of the Cisco 897VAM router.
Front Panel of the Cisco 897VAM Router
344768
Figure 1-29
LEDs
Figure 1-30 shows the back panel of the Cisco 897VAW router.
Figure 1-30
Back Panel of the Cisco 897VAW Router
11
VDSL/ADSL
overPOTS
GELAN 5
POE
54VDC
12VDC
RESET
1.2A
2.5A
GE WAN interface
On/Off switch
SFP port
Reset button
USB port
Earth ground connection
8-port Gigabit Ethernet switch
Console / Auxiliary port
Power connector
344771
CONSOLE
GE WAN
10
10 Kensington security slot
11 VDSL / ADSL over POTS
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-24
OL-16215-10
Chapter 1
Product Overview
Cisco 890 Series ISRs
Figure 1-31 shows the front panel of the Cisco 897VAW and the Cisco 897VAMW router.
Front Panel of the Cisco 897VAW and the Cisco 897VAMW Router
344770
Figure 1-31
LEDs
Figure 1-32 shows the back panel of the Cisco 897VAMW router.
Figure 1-32
Back Panel of the Cisco 897VAMW Router
11
VDSL/ADSL
overPOTS
GELAN 5
POE
54VDC
12VDC
RESET
1.2A
2.5A
GE WAN interface
On/Off switch
SFP port
Reset button
USB port
Earth ground connection
8-port Gigabit Ethernet switch
Console / Auxiliary port
Power connector
344772
CONSOLE
GE WAN
10
10 Kensington security slot
11 VDSL / ADSL over POTS
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-25
Chapter 1
Product Overview
Cisco 890 Series ISRs
Figure 1-33 shows the back panel of the Cisco 898EA router.
Figure 1-33
Back Panel of the Cisco 898EA Router
SHDSL
RJ45 ONLY
11
GELAN 5
Cisco 898EA
CONSOLE
GE WAN
POE
AUX
54VDC
12VDC
RESET
1.2A
2.5A
GE WAN interface
On/Off switch
SFP port
Reset button
USB port
Earth ground connection
8-port Gigabit Ethernet switch
Console / Auxiliary port
Power connector
344774
SFP
10
10 Kensington security slot
11 SHDSL (RJ45 Only)
1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with
the factory order, you must order and install it to enable the PoE function.
Caution
The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN
port may occur if a non-RJ-45 connector is inserted.
Figure 1-34 shows the front panel of the Cisco 898EA router.
Front Panel of the Cisco 898EA Router
344773
Figure 1-34
LEDs
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-26
OL-16215-10
Chapter 1
Product Overview
Hardware Features
Hardware Features
This section provides an overview of the following hardware features for the Cisco 860 series, 880
series, and 890 series ISRs. A feature summary is available at the end of this section.
•
Kensington Lock
•
Reset Button
•
LEDs
•
Memory
•
USB Port
•
Fan
•
Power over Ethernet Module
•
3G Cellular Data WAN Connectivity
•
Wireless LAN Connectivity
•
Small Form-Factor Pluggable Port
•
Feature Summary
Kensington Lock
A Kensington security slot is located on the router back panel. To secure the router to a desktop or other
surface, use the Kensington lockdown equipment.
Reset Button
The Reset button is used to restore the router to the factory default configurationor to load a custom
configuration file.
There are two different ways to do this:
Note
1.
by pressing the Reset button within 5 seconds of powering up the router; or
2.
by pressing the Reset button for 5 seconds while running IOS.
If you execute a CLI reboot command while the embedded wireless AP is running Cisco Unified IOS
software, the router reboots, but the AP continues running. Clients with Cisco Unified IOS software are
controlled by a wireless LAN controller (WLC) and can be reset only by the controller.
Cisco 860VAE Routers—Custom Configuration File
On Cisco 860VAE routers, the reset button can be used to load a custom configuration file without having
to use the CLI. The configuration file can be located on an external USB flash drive or on the router's
compact flash.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-27
Chapter 1
Product Overview
Hardware Features
The custom configuration file must be named one of the following:
•
customer-config
•
SN-customer-config
where “SN” is the unique hardware serial number.
When the system attempts to load a custom configuration file, configuration files on a USB flash drive
have priority over configuration files on the router's flash drive and the “SN-customer-config” file name
has priority over the “customer-config” file name. The priority for loading a configuration file is as
follows:
1.
USB flash0: SN-customer-config
2.
USB flash0: customer-config
3.
Router flash: SN-customer-config
4.
Router flash: customer-config
If the router does not find a valid custom configuration file, the system aborts the process.
To reset the router to the factory default configuration, follow these steps:
Step 1
Verify that IOS is running correctly by checking that the system status LED is on.
Step 2
Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
Custom Configuration File for Cisco 892FSP, 896VA, 897VA, and Cisco 898EA
For the first method, the configuration file can be located on the router's compact flash or on the router's
nvram. The custom configuration file must use cfg as the filename extension.
When the system attempts to load a custom configuration file, configuration files on nvram have priority
over configuration files on the router's compact flash.
The priority for loading a configuration file is as follows:
1.
nvram: *.cfg
2.
Router flash: *.cfg
If the router does not find a valid custom configuration file, the system aborts the process.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-28
OL-16215-10
Chapter 1
Product Overview
Hardware Features
To reset the router to the factory default configuration or to load a custom configuration file, follow these
steps:
Step 1
Turn the power on.
Step 2
Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
For the second method, the configuration file can be located on an external USB flash drive or on the
router's compact flash.
The custom configuration file must be named one of the following:
•
customer-config
•
customer-config.SN ?
where "SN" is the unique hardware serial number.
When the system attempts to load a custom configuration file, configuration files on a USB flash drive
have priority over configuration files on the router's flash drive and the "customer-config.SN" file name
has priority over the customer-config file name.
The priority for loading a configuration file is as follows:
1.
usbflash0:customer-config.SN
2.
usbflash0:customer-config
3.
Router flash:customer-config.SN
4.
Router flash:customer-config
If the router does not find a valid custom configuration file, the system aborts the process.
To reset the router to the factory default configuration or to load a custom configuration file, follow these
steps:
Step 1
Verify that IOS is running correctly by checking that the system status LED is on.
Step 2
Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within
5 seconds.
The router reloads itself after the startup configuration has been replaced with the new customer
configuration.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-29
Chapter 1
Product Overview
Hardware Features
LEDs
The LEDs are located on the front panel of the router.
Table 1-4
•
Table 1-4 describes the LEDs for the Cisco 860 series, 880 series, and 890 series ISRs.
•
Table 1-5 lists the LED descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and
Cisco 867VAE-K9 ISRs.
•
Table 1-6 lists the LED description for the Cisco 892FSP ISR, 896VA, 897VA, and 898EA.
LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs
LED
Color
Description
860 Series
880 Series
890 Series
Power OK
Green
On—DC power is being supplied to the router and the
Cisco IOS software is running.
All models All models All models
Blinking—Bootup is in process, or the router is in
Rommon monitor mode.
Off—Power is not supplied to the router.
Link Status FE0
Green
Link Status FE1
On—Ethernet port is connected.
Link Status FE2
Blinking—Data is either being received or being
transmitted.
Link Status FE3
Off—Ethernet port is not connected.
Link Status FE4
Green
Link Status FE5
On—Ethernet port is connected.
Link Status FE6
Blinking—Data is either being received or being
transmitted.
Link Status FE7
Off—Ethernet port is not connected.
FE WAN Port
Link Status
Green
On—Port is connected.
Blinking—Data is either being received or being
transmitted.
All models All models All models
—
—
All models
861
models
881
models
All models
—
—
All models
Wireless
models
Wireless
models
Off—Port is not connected.
GE WAN Port
Link Status
Green
On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—Port is not connected.
WLAN
(2.4 GHz)
Green
On—Radio is connected, SSID1 is configured, and client Wireless
is associated, but no data is being received or being
models
transmitted.
Slow blinking—Radio is connected, SSID is configured,
and beacons are being transmitted.
Fast blinking—Data is either being received or being
transmitted.
Off—Radio is shut down, and no SSID is configured.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-30
OL-16215-10
Chapter 1
Product Overview
Hardware Features
Table 1-4
LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED
Color
Description
860 Series
880 Series
890 Series
WLAN (5 GHz)
Green
On—Radio is connected, SSID is configured, and client is —
associated, but no data is being received or being
transmitted.
Wireless
models
Wireless
models
Wireless
models
Wireless
models
Wireless
models
Wireless
models
—
Models
with PoE
Models
with PoE
—
All models All models
—
All models All models
—
887,
896VA,
887VA,
897VA,
887VA-M8 898EA
888
models
—
887,
896VA,
887VA,
897VA,
887VA-M8 898EA
88 models
—
888E
—
—
—
898EA
Slow blinking—Radio is connected, SSID is configured,
and beacons are being transmitted.
Fast blinking—Data is either being received or being
transmitted.
Off—Radio is shut down, and no SSID is configured.
WLAN LINK
(Autonomous
Mode)
Green
On—Wireless link is up.
Blinking—Ethernet link is up, and data is either being
received or being transmitted.
Wireless
models
Off—Wireless link is down.
WLAN LINK
(Unified Mode)
Green
On—Ethernet link is up, and wireless access point (AP) is —
communicating with LWAPP2 controller.
Blinking—Ethernet link is up, but wireless AP is not
communicating with LWAPP controller.
Off—Ethernet link is down.
PoE
Green
On—PoE is connected and powered.
Off—PoE is not installed.
VPN
PPP
xDSL CD
Amber
On—Fault with the PoE.
Green
On—VPN is connected.
Green
On—At least one PPP session is established.
Green
On—The xDSL interface is connected to the DSLAM .
Blinking—Training to the line.
Off—Indicates that a connection has not been established
or the port is shut down.
xDSL Data
Green
Blinking—The xDSL interface is either receiving or
transmitting data.
Off—No data is being transmitted or being received.
xDSL ATM
Green
On—The router is operating in ATM6 mode.
Off—Not operating in ATM mode.
xDSL EFM
Green
Blink—The router is operating in EFM7 mode.
Off—Not operating in EFM mode.
Data BRI LINK
Green
On—ISDN D channel is connected.
—
887, 888
models
892
models
Data BRI B1
Green
Blinking—B1 channel is either receiving or sending data, —
or data is passing through ISDN channel 1.
887, 888
models
892
models
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-31
Chapter 1
Product Overview
Hardware Features
Table 1-4
LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
LED
Color
Description
860 Series
880 Series
890 Series
Data BRI B2
Green
Blinking—B2 channel is receiving or sending data, or
data is passing through ISDN channel 2.
—
887, 887V, 892
888
models
models
3G8 WWAN9
Green
On—Service is established.
—
3G models —
—
3G models —
Slow Blinking—Searching for service.
Fast Blinking—Data is either being received or being
transmitted.
3G RSSI10
Green
Off—Low signal strength (lower than -100 dBm).
On—High RSSI (-69 dBm or higher).
Slow Blinking—Low or medium RSSI (-99 to -90 dBm).
Fast Blinking—Medium RSSI (-89 to -70 dBm).
3G GSM
11
Amber
On—No service.
—
3G models —
Green
On—Service is established.
—
3G models —
—
3G models —
—
88113
—
Off—No service.
3G CDMA
12
Green
On—Service is established.
Off—No service.
FXO Voice
Green
On—FXO port is connected.
Blinking—FXO port is either receiving or transmitting
data.
BRI Voice LNK
Green
On—BRI interface is connected.
—
—
—
BRI Voice B1
Green
On—BRI B1 channel is connected.
—
—
—
—
—
—
—
SRST
models
—
—
—
891
models
892F
models
Blinking—BRI B1 channel is either receiving or
transmitting data.
BRI Voice B2
Green
On—BRI B2 channel is connected.
Blinking—BRI B2 channel is either receiving or
transmitting data.
FXS/DID Voice
Green
On—FXS/DID port is connected.
Blinking—FXS/DID port is either receiving or
transmitting data.
V.92 Modem
Green
On—Modem is connected.
Blinking—V.92 port is either receiving or transmitting
data.
SFP14 EN
SFP S
Off
Not present.
—
—
Green
Present and enabled.
—
—
Amber
Present with failure.
—
—
Green
Blinking—Blinking frequency indicates port speed.
—
—
892F
models
1. SSID = service set identifier.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-32
OL-16215-10
Chapter 1
Product Overview
Hardware Features
2. LWAPP = Lightweight Access Point Protocol.
3. PPP = Point-to-Point Protocol.
4. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital
subscriber line).
5. DSLAM = digital subscriber line access multiplexer.
6. ATM = Asynchronous Transfer Mode.
7. EFM = Ethernet in the First Mile.
8. 3G = Third-Generation.
9. WWAN = wireless WAN.
10. RSSI = Received Signal Strength Indicator.
11. GSM = Global System for Mobile Communication.
12. CDMA = code division multiple access.
13. SRST = Survivable Remote Site Telephony.
14. SFP = small-form-factor pluggable.
Table 1-5 describes the LEDs for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco
867VAE-K9 ISRs.
Table 1-5
LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs
LED
Activity
Description
Power/System
Power/System LED: Solid Power is on and system running in the Rommon mode.
GE_MODE LED: Off
Note
During the early booting stage, both Power/System, GE_MODE and
DSL_LINK LED: Off
DSL_LINK LED will be turned on temporarily for the power on test.
DSL_LINK and GE_MODE LED will be turned off later after booting
into Rommon.
Power/System LED: Solid IOS functioning in GE WAN mode.
GE_MODE LED: Solid
DSL_LINK LED: Off
Power/System LED: Solid IOS functioning in DSL_WAN mode.
GE_MODE LED: Off
Note
In IOS DSL_WAN mode, DSL_LINK LED will be solid after DSL
DSL_LINK LED: Solid or
training complete or flashing during training.
flashing
xDSL1 ACT
Green
On—DSL interface is up.
Blinking—DSL WAN activity (traffic in either direction).
Faster blinking—Heavier traffic
Off—Device is powered off or the DSL WAN interface is down.
xDSL Link
Green
On—DSL WAN Mode is selected and DSL training complete.
Blinking—DSL WAN Mode is selected but incomplete DSL Link Up state,
such as in-training, or controller “OFF,” or no cable attached to DSL connector.
Off—Device is powered off or GE WAN mode is selected.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-33
Chapter 1
Product Overview
Hardware Features
Table 1-5
LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs
LED
Activity
Description
GE ACT
Green
On—GE WAN interface is up.
Blinking—GE WAN activity (traffic in either direction).
Off—Device is powered off or GE WAN interface is down.
GE Mode
Green
On—GE WAN Mode is selected.
Off—Device is powered off or DSL WAN mode is selected.
1. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital
subscriber line).
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-34
OL-16215-10
Chapter 1
Product Overview
Hardware Features
Table 1-6 describes the LEDs for the Cisco 892FSP.
Table 1-6
LED desciption for Cisco 892FSP ISR, 896VA, 897VA, and 898EA Routers
LED
Color
Activity
Description
PWR_OK
Green
Power Status
Off—No power.
Steady on—Normal operation.
Blink—Boot up phase or in ROM Monitor mode.
GE0
Green/Amber
Link Status
GE1
Green On—Ethernet port is connected.
Amber On—Fault with PoE. There is a fault with
the inline power supply.
GE2
Green/Amber Blinking—Data is either being
received or being transmitted.
GE3
GE4
Green/Amber Off—Ethernet port is not
connected.
GE5
Green
Link Status
GE6
On—Ethernet port is connected.
Blinking—Data is either being received or being
transmitted.
GE7
Off—Ethernet port is not connected.
GE WAN ports Green
Link Status
On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—No link.
SFP WAN
ports
Green
Link Status
On—Port is connected.
Blinking—Data is either being received or being
transmitted.
Off—No link.
VPN_OK
Green
—
Off—No tunnel.
Steady on—At least one tunnel is up.
PPP_OK
Green
—
Off—No PPP session.
Steady on—At least one PPP established.
Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Data Routers
On the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W routers, the BRI1, BRI2 and the FXS ports
share LED indicators. The following ports share an LED indicator:
•
BRI 1B1 channel and FXS 3
•
BRI 1B2 channel and FSX 4
•
BRI 2B1 channel and FXS 5
•
BRI 2 B2 channel and FXS 6
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-35
Chapter 1
Product Overview
Hardware Features
Because the LED indicators are shared, the LED illuminates (green) when either port is active. For
example, the LED indicator labeled BRI 1 B1 illuminates when either the BRI1 B1 channel is active or
when the FXS port is active. You can determine the activity status on each interface by using the
following commands.
•
For activity status on the FXS ports, use the show port summary command.
•
For activity status on the BRI ISDN port, use the show isdn status command.
Figure 1-35 shows a close-up view of the LED indicators.
Close-up of the BRI and FXS LED Indicators
300149
Figure 1-35
Memory
The Cisco 860 series, 880 series, and 890 series routers contain flash memory and main memory.
Flash Memory
The Cisco 860 series, 880 series, and 890 series ISRs use non-upgradable flash memory storage. The
onboard flash memory contains the Cisco IOS software image, the boot flash contains the ROMMON
boot code, and a separate non-volatile flash contains the cookie configuration.
Table 1-7 describes the default flash memory storage.
Table 1-7
Flash Memory Storage
Models
Flash Memory Storage
Cisco 860 series and 880 series routers
128 MB
Cisco 880 series voice routers and Cisco 890 series routers 256 MB
Cisco 880 series routers with embedded WLAN antennas
256 MB
Cisco 860VAE routers
8 MB boot flash, 128 MB for IOS
Cisco 860VAE-K9
64 MB boot flash and IOS
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-36
OL-16215-10
Chapter 1
Product Overview
Hardware Features
Note
Flash memory is not upgradable. An external USB flash memory module may be used if additional flash
memory is needed.
Main Memory
Table 1-8 describes the main onboard memory storage for different router models.
Table 1-8
Main Onboard Memory Storage
Models
Onboard Memory Storage
Expandability
Cisco 860 series routers
256 MB
Not expandable.
Cisco 860VAE series routers 256 MB
Not expandable.
Cisco 880 series routers
A memory expansion slot accommodates
a PC2-4200, 256-MB or 512-MB double
data rate 2 (DDR2) SODIMM, for a
maximum of 768 MB.
256 MB
(expandable to 768 MB)
Cisco 880 series routers with 512 MB
embedded WLAN antennas
Not expandable.
Cisco 892FSP, 896VA,
897VA, 898EA routers
Expandable to 1 GB.
512 MB
USB Port
Table 1-9 describes the USB ports for different router models.
Table 1-9
USB Ports
Models
USB
Cisco 860 series (non-VAE)
No USB ports.
Cisco 860VAE series
One USB 1.1-compliant port located on the back panel. The USB
port does not support eToken.
Cisco 880 series
One USB 1.1-compliant port located on the front panel. The USB
port provides connection for USB devices such as security tokens
and flash memory.
Cisco 890 series1
Two USB 2.0-compliant ports located on the front panel.
Cisco 892FSP, Cisco 896VA, One USB 2.0-compliant port located on the back panel.
Cisco897VA, Cisco 898EA
1. Except for Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA.
Fan
Some router models do not have a fan, while other models have either one or two fans.
The fans spin at full speed, as a diagnostic aid, immediately after the router is powered up. After the
router has booted, the fans spin as fast as necessary to minimize fan noise while maintaining a safe
internal operating temperature.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-37
Chapter 1
Product Overview
Hardware Features
The following models have no fan:
•
Cisco 892FSP
•
Cisco 896VA
•
Cisco 897VA
•
Cisco 898EA
Power Supply
The Cisco 892FSP has a single +12V power supply input. The Cisco 892FSP power connector is
different from the barrel-type connector on other 890 series models. The AC adapter cable connector
has four pins and a built-in locking mechanism. Figure 3-27 shows the power adapter connector.
The Cisco 896VA, 897VA, and Cisco 898EA use PoE (12 VDC 43 W, -54 VDC 80 W) and non-PoE
(12 VDC 60 W) power supplies.
Power over Ethernet Module
The Cisco 880 series ISRs can include an optional Power over Ethernet (PoE) module that provides
power to 802.3af-compliant devices connected to FE ports 0 and 1.
The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant
devices connected to FE ports 0, 1, 2, and 3.
The PoE module is an option available only for the Cisco 880 series and 890 series ISRs and requires a
48 V external power adapter.
This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router
and inserting the PoE 48 V external power adapter.
Note
The Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a
30 W power supply for non-POE-enabled routers or a 60 W power supply for POE-enabled routers. For
the back panels of some of these routers, see Figure 1-17 and Figure 1-19.
3G Cellular Data WAN Connectivity
The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS])
cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data
link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony
and broadband wireless data in a mobile environment.
Some Cisco 880G models come with a 34-mm express card slot ready for use with a commercial 3G card
radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards, see the
Cisco 880 Series Integrated Services Routers Data Sheet.
Other Cisco 880G models come with embedded WAN modems for use over GSM or CDMA networks.
These routers have antenna connectors on the back panel. GSM routers have two SIM card slots. For
information on configuring Cisco 880 series ISRs for 3G, see Configuring Cisco EHWIC and 880G for
3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3.7G (HSPA+)/3.5G (HSPA).
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-38
OL-16215-10
Chapter 1
Product Overview
Hardware Features
Wireless LAN Connectivity
The embedded Wi-Fi CERTIFIED™, 802.11a/b/g/n-compliant wireless AP is preinstalled in the router
as an optional feature. The Cisco 860 series routers support autonomous features and network
configurations. The Cisco 880 series and 890 series routers support both autonomous and unified
features and network configurations.
The wireless AP does not have an external Console port. Use the router’s Console port as described in
Chapter 3, “Connecting a Terminal or PC to the Console Port.” To configure the wireless device, use the
Cisco IOS command-line interface (CLI).
Table 1-10 describes the radios and antennas for the Cisco 860 series, 880 series, and 890 series routers.
Note
Cisco 860VAE ISRs do not support wireless LAN connectivity.
The 5-GHz radio operates in the Unlicensed National Information Infrastructure (UNII) 1, 2, 3, 5-GHz
frequency bands.
Table 1-10
Wireless Device Radios and Antennas
Radio Module
Platform
Single-band
802.11b/g/n
draft 2.0 radio
module
Cisco 860 and 880 series
routers
Note
Single-band
802.11b/g/n
radio module
2.4 GHz
Cisco 880 series routers
with embedded WLAN
antennas
Up to 100 Mb/s
Mode
Antenna
Cisco 860 series:
autonomous only
Three captive,
omnidirectional dipole
antennas: 2 dBi at
2.4 GHz
Cisco 880 series:
autonomous and
unified
Cisco 860VAE
ISRs do not
support wireless
LAN connectivity.
Dual-band
802.11a/n and
802.11b/g/n
radio modules
Dual-band
simultaneous
802.11a/n and
802.11b/g/n
radio modules
Maximum Data
Radio Band Throughput1
2.4 GHz
100 Mb/s per radio, Autonomous and
up to 200 Mb/s
unified
total
2.4 GHz
and
5 GHz
Cisco 890
2.4 GHz
and 5 GHz
Three embedded,
omnidirectional
antennas: 2 dBi at
2.4 GHz
Three embedded,
dual-band,
omnidirectional
antennas: 2 dBi at
2.4 GHz and 5 dBi at
5 GHz
100 Mb/s per radio, Autonomous and
up to 200 Mb/s
unified
total
Three dual-band,
removable,
2.4-GHz/5-GHz
omnidirectional dipole
RP-TNC antenna2
1. Actual data rate is highly dependent on your wireless environment.
2. The antennas require some minor installation. They must be screwed onto the RP-TNC antenna connectors on the I/O side of the chassis. See the following
document on Cisco.com for feature information: http://www.cisco.com/en/US/docs/routers/access/wireless/hardware/notes/antdip.html
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-39
Chapter 1
Product Overview
Hardware Features
Supported Cisco Radio Antennas
The Cisco 891, Cisco 892, and Cisco 892F come with three removable dipole antennas that can be
replaced using the Cisco approved antenna extenders listed in Table 1-11.
Note
Table 1-11
Cisco supports only the antennas listed in Table 1-11 with the Cisco 890 series dual-band radio module.
Cisco Antennas Supported on the Cisco 890 Series ISRs
Cisco Part Number
Antenna Type
Maximum Gain
Description
AIR-ANTM2050D-R
Omnidirectional
2.0 dBi at 2.4 GHz
This is the default antenna. It is a swivel-mount
dipole dual-band blade antenna. For more
information, see Cisco Multiband Swivel-Mount
Dipole Antenna (AIR-ANTM2050D-R).
5.0 dBi at 5 GHz
AIR-ANTM4050V-R
Omnidirectional
4.0 dBi at 2.4 GHz
5.0 dBi at 5 GHz
AIR_ANTM5560P-R
Patch
5.5 dBi at 2.4 GHz
6.0 dBi at 5 GHz
Ceiling-mount dual-band antenna. This antenna
has a clip that allows it to be mounted on a
drop-ceiling cross member. For more information,
see Cisco Multiband Diversity Omnidirectional
Ceiling-Mount Antenna.
Wall-mount dual-band antenna. For more
information, see Cisco Multiband Wall-Mount,
Corner-Mount, or Mast-Mount Antenna.
Small Form-Factor Pluggable Port
The SFP port supports auto-media-detection, auto-failover, and remote fault indication (RFI), as
described in the IEEE 802.3ah specification.
See the Cisco 892F data sheet for a list of supported SFPs.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-40
OL-16215-10
Chapter 1
Product Overview
Hardware Features
Feature Summary
Table 1-12 summarizes the hardware features available in the Cisco 860 series, Cisco 880 series, and
Cisco 890 series ISRs.
Table 1-12
Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs
Feature
Description
860 Series
880 Series
890 Series
Reset button
Resets the router configuration to the factory default.
All models
All models
All models
Resets the router configuration to customer configuration.
866VAE,
—
867VAE,
866VAE-K9,
867VAE-K9
—
FE1 built-in
switch ports
Provides connection to 10/100BASE-T (10/100-Mb/s)
All models
Fast Ethernet networks. The autosensing function in these
routers eliminates the need for a crossover cable and enables
the router to detect MDI2 or MDIX3 in any other PC or hub
with a straight-through cable or a crossover cable.
GE4 built-in
switch port
Provides connection to 10/100/1000BASE-T
866VAE-K9, —
(10/100/1000-Mb/s) Gigabit Ethernet networks. The
867VAE-K9
autosensing function in these routers eliminates the need for
a crossover cable and enables the router to detect MDI5 or
MDIX6 in any other PC or hub with a straight-through cable
or a crossover cable.
892FSP,
896VA,
897VA,
897VAM,
897VAW,
897VAMW,
898EA
Console or AUX
port
All models
Provides a connection to the terminal or PC for software
configuration or troubleshooting. The Console port may be
configured as a virtual auxiliary port for dial backup and
remote management.
All models
All models
861, 867,
All models
866VAE-K9,
867VAE-K9
All models
All models
891, 892,
892F
Cisco 891, Cisco 892, and Cisco 892F have separate console
and auxiliary ports.
Cisco 892FSP has combined console and auxiliary port.
Security features Provides support for VPNs7, Cisco IOS Firewall, and
IPSec8. The Cisco 880 series routers also provide URL
filtering.
Embedded
wireless AP
FE WAN port
Provides Wi-Fi CERTIFIED™ 802.11a/b/g/n compliance. Wireless
models
The Cisco 860 series routers contain a single 802.11b/g/n
radio.
802.11b/g/n
Some Cisco 880 series routers contain a single 802.11b/g/n
radio while others contain dual 802.11a/n and 802.11b/g/n
radios.
The Cisco 890 series routers contain dual 802.11b/g/n and
802.11a/n radios.
Provides connection to 10/100BASE-T. Can be connected to 861
other network devices, such as a cable modem, an xDSL11
modem, or router. The router is capable of bridging and
multiprotocol routing between the LAN and WAN ports.
Wireless
models
Wireless
models
802.11b/g/n9
and
802.11a/n10
802.11b/g/n
and
802.11a/n
881
891, 892,
892F
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-41
Chapter 1
Product Overview
Hardware Features
Table 1-12
Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
Feature
Description
860 Series
GE WAN port
10/100/1000 GE WAN Port.
866VAE,
—
867VAE,
866VAE-K9,
867VAE-K9
All models
VDSLoPOTS12
port
Provides connection to a VDSL network.
—
887V
—
ADSLoPOTS
Provides ADSL connection over basic telephone service
—
with Annex A and Annex B ITU G. 992.1 (ADSL), G.992.3
(ADSL2), and G.992.5 (ADSL).
—
—
ADSLoISDN
Provides ADSL connection over ISDN.
—
—
DSL Multi-mode Provides ADSL2/2+ or VDSL connection over POTS or
ISDN (ISDN on 886VA only).
(VDSL and
ADSL2/2+)
—
880 Series
890 Series
866VAE,
886VA,
867VAE,
887VA,887V
866VAE-K9, A-M
867VAE-K9
892FSP,
896VA,
897VA,
897VAM,
897VAW,
897VAMW,
898EA
Real-time clock
(RTC)
RTC provides nonvolatile date and time when the router is
powered on. The RTC is used for verifying the validity of the
Certification Authority stored on the router. It is backed up
by a nonreplaceable lithium battery.
866VAE,
All models
867VAE,
866VAE-K9,
867VAE-K9
All models
USB port,
Supports USB 1.1. Provides connection for USB devices
such as security tokens and flash memory.
866VAE,
All models
867VAE,
866VAE-K9,
867VAE-K9
All models
—
Models with
PoE
Models with
PoE
The Cisco 880 series routers have a single USB port; the
Cisco 890 series routers have two USB ports.
Cisco 880 series routers with embedded WLAN antennas
have one USB 2.0 port.
Cisco 892FSP and Cisco 860VAE series routers have one
USB 2.0 port on the rear panel for temporary installation of
a Cisco-approved USB memory device for maintenance
purposes only. The port supports only USB 2.0. Refer to the
product datasheet for the list of supported USB flash
memory devices.
Note
PoE13
Cisco 860VAE series router USB port does not
support eToken.
(Optional) Provides power for 802.3af-compliant devices
(such as phones) that are connected to the router.
The Cisco 880 series routers support a 2-port PoE module;
the Cisco 890 series routers support a 4-port PoE module.
G.SHDSL14 port
Provides 2-wire or 4-wire connection to a G.SHDSL
network.
—
888
898EA
3G15 card slot
Provides backup data link.
—
3G models
—
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-42
OL-16215-10
Chapter 1
Product Overview
Hardware Features
Table 1-12
Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)
Feature
Description
860 Series
880 Series
Dying gasp
Detects when the router is losing power, and sends a
power-fail signal to warn the DSLAM16 about the
impending line drop.
866VAE,
888EA,
867VAE,
xDSL models
866VAE-K9,
867VAE-K9,
xDSL
models
890 Series
892FSP,
896VA,
897VA,
897VAM,
897VAW,
897VAMW,
898EA
Data BRI port
—
Provides backup and remote management functions by
connecting to the ISDN service provider if the main VDSL
or G.SHDSL link fails.
V.92 modem
Provides dial backup and remote management functions if
the main WAN link fails.
—
—
891
FXO18 port
An FXO interface connects local calls to a central office or
PBX. This is the interface a standard telephone provides.
—
881 SRST
—
FXS19/DID20
port
An FXS interface connects directly to a standard telephone, —
fax machine, or similar device. This interface supplies
ringing voltage and dial tone to the station.
SRST models —
BRI voice port
The ISDN BRI S/T voice interface provides a client-side
—
(TE) ISDN S/T physical interface for connection to an NT1
device that terminates an ISDN telephone network.
887V
—
SFP21 port
Supports auto-media-detection, auto-failover, and remote
fault indication (RFI), as described in the IEEE 802.3ah
specification.
—
892F
models,
892FSP,
896VA,
897VA,
897VAM,
897VAW,
897VAMW,
898EA
See the Cisco 892F data sheet for a list of supported SFPs.
—
xDSL
892
models,
except for the
3G and
SRST17
models
1. FE = Fast Ethernet.
2. MDI = media-dependent interface in normal mode.
3. MDIX = media-dependent interface in crossover mode.
4. GE = Gigabit Ethernet.
5. MDI = media-dependent interface in normal mode.
6. MDIX = media-dependent interface in crossover mode.
7. VPN = Virtual Private Network.
8. IPsec = IP security.
9. This applies to most models of the Cisco 880 series routers.
10. This applies to Cisco 880 series routers with embedded, wireless antennas.
11. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital
subscriber line), and G.SHDSL.
12. VDSLoPOTS = very-high-data-rate digital subscriber line 2 over plain old telephone service.
13. PoE = Power over Ethernet. This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router and inserting the
PoE 48-V external power adapter.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
OL-16215-10
1-43
Chapter 1
Product Overview
Hardware Features
14. G.SHDSL = (global industry standard) symmetrical high-speed DSL.
15. 3G = Third-Generation.
16. DSLAM = digital subscriber line access multiplexer.
17. SRST = Survivable Remote Site Telephony.
18. FXO = Foreign Exchange Office.
19. FXS = Foreign Exchange Station.
20. DID = Direct Inward Dialing.
21. SFP = small-form-factor pluggable.
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide
1-44
OL-16215-10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2013:05:03 17:54:31+08:00
Create Date                     : 2013:05:03 17:53:59+08:00
Metadata Date                   : 2013:05:03 17:54:31+08:00
Creator Tool                    : FrameMaker 7.2
Format                          : application/pdf
Title                           : HIG880-860.book
Creator                         : panilkum
Document ID                     : uuid:fdc5bebc-bf66-4e67-a7e2-1b82c02232a9
Instance ID                     : uuid:5946ca72-b860-4683-bd62-ecf3facd66d7
Producer                        : Acrobat Distiller 10.1.5 (Windows)
Page Count                      : 60
Author                          : panilkum

EXIF Metadata provided by EXIF.tools