GemTek Technology CISCO867VAE XDSL Router User Manual HIG880 860

Gemtek Technology Co., Ltd. XDSL Router HIG880 860

UserManual.wiki >

GemTek Technology >

CISCO867VAE User Manual >

User Manual Part 1 HTML Version

User Manual Part 1

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco 860 Series, Cisco 880 Series, and

Cisco 890 Series Integrated Services

Routers Hardware Installation Guide

Last Revised: March 6, 2013

Text Part Number: OL-16215-10

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required

to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not

installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to

comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital

devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television

communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its

peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits

controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this

URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership

relationship between Cisco and any other company. (1110R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the

document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

iii

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

CONTENTS

Preface vii

Objective vii

Audience vii

Organization viii

Conventions viii

Related Documentation

In addition to the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR Hardware Installation

Guide (this document), the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISR documentation

set includes the following documents:

• Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers

• Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software

Configuration Guide

• Software Activation on Cisco Integrated Services Routers and Cisco Integrated Service Routers G2

• Cisco IOS Software Activation Configuration Guide

• Declarations of Conformity and Regulatory Information for Cisco Access Products with 802.11a/b/g

and 802.11b/g Radios

• Cisco IOS Release Notes

• Cisco IOS Quality of Service Solutions Command Reference, Release 12.4T

• Cisco IOS Security Configuration Guide, Release 12.4T

• Cisco IOS Security Command Reference, Release 12.4T

• Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges, versions 12.4(10b) JA

and 12.3(8) JEC

• Wireless LAN Controllers

• Unified Wireless LAN Access Points

• Cisco IOS Voice Port Configuration Guide

• SCCP Controlled Analog (FXS) Ports with Supplementary Features in Cisco IOS Gateways

• Cisco CP Express User’s Guide

xvi

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Preface

Searching Cisco Documents

To search a HTML document using a web browser, press Ctrl-F (Windows) or Cmd-F (Apple). In most

browsers, the option to search whole words only, invoke case sensitivity, or search forward and backward

is also available.

To search a PDF document in Adobe Reader, use the basic Find toolbar (Ctrl-F) or the Full Reader

Search window (Shift-Ctrl-F). Use the Find toolbar to find words or phrases within a specific document.

Use the Full Reader Search window to search multiple PDF files simultaneously and to change case

sensitivity and other options. Adobe Reader’s online help has more information about how to search PDF

documents.

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional

information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and

revised Cisco technical documentation:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as an RSS feed and set content to be

delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently

supports RSS Version 2.0.

CHAPTER

1-1

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Product Overview

This chapter provides an overview of the features available for the Cisco 860 series, Cisco 880 series,

and Cisco 890 series Integrated Services Routers (ISRs), and contains the following sections:

• General Description, page 1-2

• Cisco 860 Series ISRs, page 1-2

• Cisco 860VAE Series ISRs, page 1-3

• Cisco 880 Series ISRs, page 1-6

• Cisco 890 Series ISRs, page 1-17

• Hardware Features, page 1-27

Note For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap

that ships with the router and Regulatory Compliance and Safety Information for Cisco 800 Series and

SOHO Series Routers.

Note Some illustrations in this document show a wireless router. Both wireless and nonwireless models are

available in the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs. Port and feature locations

are similar for both wireless and nonwireless routers.

Note Throughout this document the term VDSL refers to support for VDSL2 (ITU G.993.2) and ADSL refers

to support for ADSL, ADSL2, & ADSL2+ (ITU G.992.1, G.992.3, & G.992.5).

1-2

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

General Description

The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs provide data, voice, Wi-Fi

CERTIFIED™ wireless access point (AP), integrated Virtual Private Network (VPN), and backup

capabilities to corporate teleworkers and to remote and small offices with fewer than 20 users. These

routers are capable of bridging and multiprotocol routing between LAN and WAN ports. The routers

provide advanced features, such as high speed DSL (G.SHDSL, ADSL, or VDSL), 802.11n, quality of

service (QoS), firewall, antivirus protection, and Secure Socket Layer (SSL). The Cisco 860VAE, 886VA

and 887VA series routers have the additional capability of DSL Multi-mode (VDSL/ADSL).

The Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs have a desktop form factor with

built-in wall-mount features. The Cisco 890 series ISRs also have optional rack-mount features. These

ISRs are powered by an external power supply adapter. The various models differ in the WAN interface

and features that they support.

Cisco 860 Series ISRs

The Cisco 860 series ISRs are fixed-configuration data routers that support the following features:

• An integrated 4-port 10/100 Ethernet switch for connecting to the LAN

• A10/100 Fast Ethernet (FE) port for connecting to the WAN.

• Optional, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP

Figure 1-1 shows the front panel details of the Cisco 860 wireless router.

Figure 1-1 Front Panel of the Cisco 860 Series Wireless ISR

1LEDs

231969

1-3

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 860VAE Series ISRs

Figure 1-2 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do

not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series

routers.

Figure 1-2 Back Panel of the Cisco 861W ISR

Cisco 860VAE Series ISRs

The Cisco 860VAE series ISRs are fixed-configuration data routers. This section describes the features

of the products in this series.

Interfaces

Table 1-1 describes the interfaces of the Cisco 860VAE series routers.

1Primary WAN port—10/100 5Reset button

2Antenna—captive omnidirectional dipole

WLAN antenna (wireless models only)

6Power connector

34-port 10/100 Ethernet switch 7Earth ground connection

4Serial port—console or auxiliary 8Kensington security slot

232181

31 4 6 7 852

WAN

FE 4

Cisco 861W

Ta b l e 1-1 Interfaces of the Cisco 860VAE Series ISRs

Interfaces

Model

866VAE 867VAE 866VAE-K9 867VAE-K9

4 FE1 switch ports xxxx

1 GE2 switch port — — x x

1 GE WAN port xxxx

1-4

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 860VAE Series ISRs

Note The Cisco 866VAE, 867VAE, 866VAE-K9, and 867VAE-K9 routers each have two WAN ports. Only one

of the two ports can be active at any given time.

IOS Images

Table 1-2 describes the IOS images included in Cisco 860VAE series routers.

Figure 1-3 shows the front panel details of the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and

Cisco 867VAE-K9 integrated services routers (ISRs).

Figure 1-3 Front Panel of the Cisco 860VAE series ISR

1 VDSL/ADSL over POTS port — x — x

1 VDSL/ADSL over ISDN port x — x —

1. FE = Fast Ethernet

2. GE = Gigabit Ethernet

Table 1-1 Interfaces of the Cisco 860VAE Series ISRs (continued)

Interfaces

Model

866VAE 867VAE 866VAE-K9 867VAE-K9

Ta b l e 1-2 IOS Images of the Cisco 860VAE Series ISRs

IOS Image

Model

866VAE 867VAE 866VAE-K9 867VAE-K9

c860vae-ipbasek9-mz x x — —

c860vae-advsecurityk9-mz — — x x

c860vae-advsecurityk9_npe-mz — — x x

1LEDs

246199

Cisco 860 Series

1-5

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 860VAE Series ISRs

Figure 1-4 shows the back panel details of the Cisco 866VAE ISR.

Figure 1-4 Back Panel of the Cisco 866VAE ISR

Figure 1-5 shows the back panel details of the Cisco 867VAE-K9.

Figure 1-5 Back Panel of the Cisco 867VAE-K9 ISR

1xDSL port1

1. Using RJ-11.

6On/Off switch

2GE WAN interface 7Power connector

3Ethernet LAN FE interfaces (FE0 through

FE3 interfaces)

8Reset button

4USB port 9Kensington security slot

5Serial port—console or auxiliary

246200

CONSOLE

AUX

FE 2 FE 1 FE 0FE 3OVER ISDN

LAN

WAN

GE0

VDSL/ADSL

12V 2.5A

RESET

Cisco 866VAE

1 2 3 4 7 8 95 6

1xDSL port 6On/Off switch

2GE WAN interface 7Power connector

3Ethernet LAN GE and FE interfaces (GE0

interface and FE0 through FE3 interfaces)

8Reset button

4USB port 9Kensington security slot

5Serial port—console or auxiliary

284558

CONSOLE

AUX

OVER POTS

WAN LAN

GE1 GE0 FE3 FE2 FE1 FE0

VDSL/ADSL

12V 2.5A

RESET

Cisco 867VAE-K9

1 2 3 4 7 8 95 6

1-6

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

The Cisco 880 series ISRs have data and voice capabilities. They have the following features:

• Integrated 4-port 10/100 Ethernet switch for connecting to the LAN

• 10/100 FE, VDSLoPOTS, ADSL over POTS, ADSL over ISDN, DSL Multi-mode

(VDSL/ADSLoPOTS, VDSL/ADSLoISDN Cisco VA models only), or G.SHDSL port for

connecting to the WAN

• Optional embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP

• Optional 2-port Power over Ethernet (PoE)

Note The Cisco 880 series ISRs can include an optional PoE module that provides power to

802.3af-compliant devices connected to ethernet ports 0 and 1. If this feature was not

configured with the factory order, you must order and install it to enable the PoE function.

• DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB

system memory

The following features are located on the front panel:

• USB 1.1 port

• Express card slot for third-generation (3G) cellular data WAN connectivity, available only on the

Cisco 880G models

This section contains the following topics:

• Cisco 880 Series Data Routers, page 1-6

• Cisco 880 Series Voice and Data Routers, page 1-9

• Cisco 880 Series with Embedded WLAN Antennas, page 1-15

Cisco 880 Series Data Routers

The Cisco 880 series data routers provide integrated VPN, embedded Wi-Fi CERTIFIED™,

802.11b/g/n-compliant wireless AP, 3G, and backup capabilities. Figure 1-6 through Figure 1-9 show

the features available on Cisco 880 series data routers. Some of the features shown may not be available

on your router.

Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, VDSL/ADSL

over ISDN, VDSL/ADSL over POTS, or 10/100 FE. See the Cisco 880 Series Integrated Services

Routers data sheet for the WAN interface that is supported on your router.

Figure 1-6 shows the front panel details of the Cisco 880 wireless data router. The USB port and the 3G

card slot are located on the front panel.

1-7

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-6 Front Panel of the Cisco 880 Series Wireless Data Router

Figure 1-7 shows the back panel details of the Cisco 886VA data router.

Figure 1-7 Back Panel of the Cisco 886VA Router

1LEDs 3USB port

23G express card slot—Supports third-party1

3G card (Cisco 880G models only)

1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors.

231950

1 2 3

254090

1 3 4 5 7 8 962

1Data BRI1 0 6Reset button

2Primary WAN port—VDSL/ADSL over

ISDN

7Power connector

34-port 10/100 Ethernet switch28Earth ground connection

4Serial port—console or auxiliary 9Kensington security slot

5PoE power connector—optional

1. BRI = Basic rate interface.

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN

port may occur if a non-RJ-45 connector is inserted.

1-8

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-8 shows the back panel details of the Cisco 887VA and 886VA-M data router.

Figure 1-8 Back Panel of the Cisco 887VA and 887VA-M Router

Figure 1-9 shows the back panel details of the Cisco 888W data router. Nonwireless routers do not have

antennas on the back panel. However, the feature locations are similar across all Cisco 880 series data

routers.

Figure 1-9 Back Panel of the Cisco 888W Data Router

254139

2 3 4 6 7 851

1Primary WAN port—VDSL/ADSL over

POTS15Reset button

24-port 10/100 Ethernet switch26Power connector

3Serial port—console or auxiliary 7Earth ground connection

4PoE power connector—optional 8Kensington security slot

1. 887VA-M has Annex M support.

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

Caution For the Cisco 887VA, the primary WAN port is designed for an RJ-45 connector only. Damage

to the primary WAN port may occur if a non-RJ-45 connector is inserted.

231951

1 4 5 6 8 9 1072 3

1-9

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Cisco 880 Series Voice and Data Routers

The Cisco 880 series voice and data routers provide both voice and data ports. The voice ports managed

voice services that interface with Foreign Exchange Station (FXS), Foreign Exchange Office (FXO), or

BRI connections.

Cisco 881 SRST and Cisco 888 SRST

Figure 1-10, Figure 1-11, and Figure 1-12 show the features available on the Cisco 881 SRST and

Cisco 888 SRST routers. The features available vary, depending on the router model. Some features may

not be available on your router.

Depending on the router model, the primary WAN port can be either G.SHDSL or 10/100 FE. See the

Cisco 880 Series Integrated Services Routers data sheet for the WAN interface and voice ports that are

supported on your router.

1ISDN port—not available on 3G models 6PoE power connector for optional PoE

module1

2Primary WAN port2—G.SHDSL,

VDSLoPOTS, ADSLoPOTS, ADSLoISDN,

or 10/100 FE

7Reset button

3Antenna—captive omnidirectional dipole

WLAN antenna (wireless models only)

8Power connector

44-port 10/100 Ethernet switch 9Earth ground connection

5Serial port—console or auxiliary 10 Kensington security slot

1. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected

to ethernet ports 0 and 1. If this feature was not configured with the factory order, you must order and install it to enable the

PoE function.

2. Depending on the router model, the primary WAN port can be G.SHDSL, VDSLoPOTS, or 10/100 FE. The VDSLoPOTS

port is in the same location as the G.SHDSL port. The 10/100 FE WAN port is located at the bottom left corner. See Figure 1-2

for the location of the 10/100 FE WAN port.

1-10

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-10 shows the front panel details of the Cisco 881 SRST and Cisco 888 SRST wireless voice

router.

Figure 1-10 Front Panel of the Cisco 881 SRST and Cisco 888 SRST Wireless Voice Router

1LEDs 2USB port

270495

1 2

1-11

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-11 shows the back panel details of the Cisco 881SRST-W voice router.

Figure 1-11 Back Panel of the Cisco C881SRST-W Voice Router

1Primary WAN port1—10/100 FE

1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.

6Antenna—captive wireless omnidirectional

dipole WLAN antenna (wireless models only)

2Voice ports—four FXS2/DID3 ports, one

FXO4 port with TBP5 power failover

2. FXS = Foreign Exchange Station.

3. DID = Direct Inward Dialing.

4. FXO = Foreign Exchange Office.

5. TBP = trunk bypass.

7Reset button

34-port 10/100 Ethernet switch6

6. Ports 0 and 1 provide PoE with the optional PoE module installed.

8Power connector

4Serial port—console or auxiliary 9Earth ground connection

5PoE power connector for optional PoE

module7

7. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected

to ethernet ports 0 and 1. If this feature was not configured with the factory order, SKU 800-IL-PM-2, you must order and

install it to enable the PoE function. The PoE power supply, SKU 800-ILPM-4, is also required.

10 Kensington security slot

241904

31 4 7 98 1022 56

1-12

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-12 shows the back panel details of the Cisco 888SRST-W voice router.

Figure 1-12 Back Panel of the Cisco C888SRST-W Voice Router

1Primary WAN port1—G.SHDSL

1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE.

6Antenna—captive wireless omnidirectional

dipole WLAN antenna (wireless models only)

2Voice ports—four FXS/DIDports and one

voice BRI port

7Reset button

34-port 10/100 Ethernet switch2

2. Ports 0 and 1 provide PoE with the optional PoE module installed.

8Power connector

4Serial port—console or auxiliary 9Earth ground connection

5PoE power connector for optional PoE

module3

3. The Cisco 880 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected

to ethernet ports 0 and 1. If this feature was not configured with the factory order, SKU 800-IL-PM-2, you must order and

install it to enable the PoE function. The PoE power supply, SKU 800-ILPM-4, is also required.

Caution The primary WAN port on all 888E models is designed for an RJ-45 connector only. Damage

to the primary WAN port may occur if a non-RJ-45 connector is inserted.

10 Kensington security slot

241905

32 2 4 7 9 1086 51

1-13

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W

Figure 1-13, Figure 1-14, and Figure 1-15 show the features available on the Cisco 881-V and

Cisco 887VA-V routers. The features available vary, depending on the router model. Some features may

not be available on your router.

The Cisco 881-V and Cisco 887VA-V voice and data series gives you the flexibility to use either FXS

or BRI voice ports. However, the number of concurrent calls that can be supported by the router is limited

by the codec complexity setting on the router. Table 1-3 lists the maximum number of calls that is

supported when the codec complexity command is configured for Flexible, Medium or High complexity.

Note Configuring the codec complexity setting to support secure calls uses DSP resources, but does not affect

the maximum number of supported calls.

Figure 1-13 shows the front panel details of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W.

Figure 1-13 Front Panel of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W Routers

Ta b l e 1-3 Maximum Number of Supported Calls

Flexible Complexity Medium Complexity High Complexity

C881-V 986

C887VA-V 886

C887VA-V-W 886

246861

1 2

1LEDs 2USB port

1-14

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-14 shows the back panel for the Cisco 887VA-V-W router. The Cisco 887VA-V (non-wireless)

router does not have the antennas on the back panel.

Figure 1-14 Back Panel of the Cisco 887 VA-V Router

Figure 1-15 shows the back panel for the Cisco 881-V router.

Figure 1-15 Back Panel of the Cisco 881-V Router

246864

overP O TS

VDSL/AD SL

C887VA-W VOICE

1 4 5 6 8 9 107

1Data BRI 7Reset Button

2Voice BRI 8Power connector

3Voice ports—four FXS/DID ports 9 Earth ground connection

4Fast Ethernet LAN—four ports 10 Kensington security slot

5Console Port 11 Primary WAN port—VDSL/ADSL over

POTS

6PoE power connector (optional)

246866

C881 VOICE

56 7

1 4 5 6 8 9 10732

1-15

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Cisco 880 Series with Embedded WLAN Antennas

Some Cisco 880W, 880WD, and 880-WD ISRs have three embedded WLAN antennas.

These ISRs are fixed-platform routers that:

• Provide integrated VPN, embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless AP, and

backup capabilities.

• Use single-band (2.4 GHz) WLAN cards or dual-band (2.4 GHz and 5 GHz) WLAN cards.

• Require a single external power supply: a 30-W power supply for non-POE-enabled routers or a

60-W power supply for POE-enabled routers.

• Have a fixed 512 MB of system memory.

For information on configuring the Cisco 880 series ISRs, see Cisco 880 Series Integrated Services

Router Software Configuration Guide.

Cisco 887VA-WD

Figure 1-16 shows the front panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs. The

front panel has LEDs only. All the ports are in the back panel.

Figure 1-16 Front Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs

1Fast Ethernet WAN port 6PoE power connector (optional)

2Voice BRI ports 7Reset button

3Voice ports—four FXS/DID ports and one

FXO port.

8Power connector

4Fast Ethernet LAN—four ports 9Earth ground connection

5Console Port 10 Kensington security slot

284983

OK PPP

WLAN

POE

01LINK 2.4GHz 5GHz

Cisco 800 Series

FE LAN

VPN

0123

xDSL

CD DATA

1-16

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 880 Series ISRs

Figure 1-17 shows the back panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs.

Figure 1-17 Back Panel of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs

C881WD

Figure 1-18 shows the front panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs. The front

panel has LEDs only. All the ports are in the back panel.

Figure 1-18 Front Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs

284988

Cisco 887VA-WD

AUX

CONSOLE

FE LAN

POE OPTION

REQUIRES 5A

POWER

ADAPTOR

3210

RESET 12VDC 5A

overPOTS

1 2 3 4 5 6 7

284988

Cisco 887VA-WD

AUX

CONSOLE

FE LAN

POE OPTION

REQUIRES 5A

POWER

ADAPTOR

3210

RESET 12VDC 5A

overPOTS

1 2 3 4 5 6 7

1USB port 6Power connector

24-port 10/100 Ethernet switch 7Kensington security slot

3Serial port—console or auxiliary 8Power switch

4Note No separate PoE power supply is

required for routers with embedded

WLAN antennas. For information on

system power supply requirements

when PoE is enabled, see the “Power

over Ethernet Module” section on

page 1-38.

9VDSL/ADSL port

5Reset button

284982

OK PPP

FE4

WAN

WLAN

POE

01LINK 2.4GHz 5GHz

Cisco 800 Series

FE LAN

VPN

0123

1-17

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-19 shows the back panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs.

Figure 1-19 Back Panel of the C881WD-A-K9 and C881WD-E-K9 ISRs

Cisco 890 Series ISRs

Cisco 891, Cisco 892, and Cisco 892F

The Cisco 891, Cisco 892, and Cisco 892F ISRs have the following features:

• Integrated 8-port 10/100 Ethernet switch for connecting to the LAN

• 10/100 FE and 10/100/1000 Gigabit Ethernet (GE) port for connecting to the WAN

• Separate console and auxiliary ports

• Optional embedded Wi-Fi CERTIFIED™ dual radio 802.11a/b/g/n-compliant wireless AP

• Optional 4-port PoE

Note The Cisco 890 series ISRs can include an optional PoE module that provides power to

802.3af-compliant devices connected to ethernet ports 0 through 3. If this feature was not

configured with the factory order, you must order and install it to enable the PoE function.

• Security feature card (SFC) socket

284987

Cisco 881WD

AUX

CONSOLE

FE LAN

POE OPTION

REQUIRES 5A

POWER

ADAPTOR

3210

RESET 12VDC 5A

FE WAN

21 3 4 5 6 7 8

1Primary WAN port—10/100 FE 6Reset button

2USB port 7Power connector

34-port 10/100 Ethernet switch 8Kensington security slot

4Serial port—console or auxiliary 9Power switch

5Note No separate PoE power supply is

required for routers with embedded

WLAN antennas. For information on

system power supply requirements

when PoE is enabled, see the “Power

over Ethernet Module” section on

page 1-38.

1-18

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

• DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB

system memory in Cisco 891 and 892 series ISRs, and a total of 1 GB system memory in

Cisco 892F series ISRs

• Three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel for

non-captive dual-band WLAN antenna (wireless models only)

• Support for the AIM2-CUE-K9 and AIM2-APPRE-104-K9

• GE small-form-factor pluggable (SFP) port (Cisco 892F series ISRs only)

The following feature is located on the front panel:

• Two USB 2.0 ports

Figure 1-20 shows the front panel details of the Cisco 890 wireless router.

Figure 1-20 Front Panel of the Cisco 890 Series Wireless ISR

1LEDs 2USB ports

272367

1 2

1-19

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-21 shows the back panel details of the Cisco 892-W router. Nonwireless routers do not have

RP-TNC antennas or connectors on the back panel. Some of the features that are shown may not be

available on your router. However, the feature locations are similar across all Cisco 890 series routers.

Figure 1-21 Back Panel of the Cisco 892-W Router

1Antenna—dipole swivel antenna attached to

RP-TNC connectors (wireless models only)

7PoE power connector for optional PoE

module1

1. The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant devices connected

to ethernet ports 0 through 3. If this feature was not configured with the factory order you must order and install it to enable

the PoE function.

2Backup—Data BRI2 or V.923 port

2. The Data BRI port is available only on the Cisco 892 router models.

3. The V.92 port (not shown) is available only on the Cisco 891 router models and is located between the console port and the

Ethernet switch.

8Reset button

3Primary WAN port—FE and GE 9Power connector

4Auxiliary port 10 Earth ground connection

5Console port 11 Kensington security slot

68-port 10/100 Ethernet switch

272369

14 5 6 8 9 10 1172 3

1-20

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-22 shows the location of the SFP port in a Cisco 892F-W router.

Figure 1-22 SFP Port Location in a Cisco 892F-W Router

Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA

The Cisco 892FSP, 896VA, 897VA (897VA, 897VAM, 897VAW, 897VAMW), and 898EA routers have

the following features:

• Integrated 8-port 10/100/1000 Gigabit Ethernet(GE) switch for connecting to the LAN

• Two 10/100/1000 GE ports for the Cisco 892FSP

• One 10/100/1000 GE port for the Cisco 896VA, 897VA, and the Cisco 898EA. Either the SFP socket

or the 10/100/1000 GE port can be active at a given time, but not both.

• Single console and auxiliary ports for configuration and management

• 512 MB of on-board memory (upgrade option to 1 GB)

• 256 MB flash memory for the Cisco 896VA, 897VA, and Cisco 898EA

• One USB 2.0 port

• Optional internal adapter for inline PoE on 4 switch ports for IP phones or external wireless access

points for Cisco 896VA, 897VA, and 898EA models only. No PoE support on Cisco 892FSP.

Note The Cisco 892FSP does not support AIM2-CUE-K9 and AIM2-APPRE-104-K9 because it does not have

an SFC socket.

1SFP port 2SFP LEDs

278179

Cisco 892F-W

SFP

1-21

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-23 shows the back panel of the Cisco 892FSP router.

Figure 1-23 Back Panel of the Cisco 892FSP Router

Figure 1-24 shows the front panel of the Cisco 892FSP router.

Figure 1-24 Front Panel of the Cisco 892FSP Router

GE W AN

SFP

812VD C 2.5A

CONSOLE

AUX RESE T

Cisco 892FSP

284781

2 3 4 5 6 8 9 1071

1GE WAN interface 6Power connector

2SFP port 7On/Off switch

3USB port 8Reset button

48-port Gigabit Ethernet switch 9Earth ground connection

5Console / Auxiliary port 10 Kensington security slot

284782

1LEDs

1-22

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-25 shows the back panel of the Cisco 896VA router.

Figure 1-25 Back Panel of the Cisco 896VA Router

Figure 1-26 shows the front panel of the Cisco 896VA and the Cisco 897VA router.

Figure 1-26 Front Panel of the Cisco 896VA and Cisco 897VA Router

7 6 GELAN 5 4

3 2 POE 1 0

ISDN

GE WAN

54VDC 1.2A

12VDC 2.5A

VDSL/ADSL

overISDN

CONSOLE

RESET

Cisco 896VA

1 2 34 5 89 10 11

6 7

344766

1ISDN 7Power connector

2GE WAN interface 8On/Off switch

3SFP port 9Reset button

4USB port 10 Earth ground connection

58-port Gigabit Ethernet switch111 Kensington security slot

6Console / Auxiliary port 12 VDSL / ADSL over ISDN

1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with

the factory order, you must order and install it to enable the PoE function.

344765

1LEDs

1-23

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-27 shows the back panel of the Cisco 897VA router.

Figure 1-27 Back Panel of the Cisco 897VA Router

Figure 1-28 shows the back panel of the Cisco 897VAM router.

Figure 1-28 Back Panel of the Cisco 897VAM Router

7 6 GELAN 5 4

3 2 POE 1 0

ISDN

GE WAN

54VDC 1.2A

12VDC 2.5A

VDSL/ADSL

overPOTS

CONSOLE

RESET

Cisco 897VA

344767

1 2 34 5 89 10 11

6 7

1ISDN 7Power connector

2GE WAN interface 8On/Off switch

3SFP port 9Reset button

4USB port 10 Earth ground connection

58-port Gigabit Ethernet switch111 Kensington security slot

6Console / Auxiliary port 12 VDSL / ADSL over POTS

1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with

the factory order, you must order and install it to enable the PoE function.

7 6 GELAN 5 4

3 2 POE 1 0

GE WAN

54VDC 1.2A

12VDC 2.5A

VDSL/ADSL

overPOTS

CONSOLE

RESET

344769

1 2 34 7 89 10

5 6

1GE WAN interface 7On/Off switch

2SFP port 8Reset button

3USB port 9Earth ground connection

1-24

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-29 shows the front panel of the Cisco 897VAM router.

Figure 1-29 Front Panel of the Cisco 897VAM Router

Figure 1-30 shows the back panel of the Cisco 897VAW router.

Figure 1-30 Back Panel of the Cisco 897VAW Router

48-port Gigabit Ethernet switch110 Kensington security slot

5Console / Auxiliary port 11 VDSL / ADSL over POTS

6Power connector

1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with

the factory order, you must order and install it to enable the PoE function.

344768

1LEDs

7 6 GELAN 5 4

3 2 POE 1 0

GE WAN

54VDC 1.2A

12VDC 2.5A

VDSL/ADSL

overPOTS

CONSOLE

RESET

344771

1 2 34 7 89 10

5 6

1GE WAN interface 7On/Off switch

2SFP port 8Reset button

3USB port 9Earth ground connection

48-port Gigabit Ethernet switch110 Kensington security slot

5Console / Auxiliary port 11 VDSL / ADSL over POTS

6Power connector

1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with

the factory order, you must order and install it to enable the PoE function.

1-25

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-31 shows the front panel of the Cisco 897VAW and the Cisco 897VAMW router.

Figure 1-31 Front Panel of the Cisco 897VAW and the Cisco 897VAMW Router

Figure 1-32 shows the back panel of the Cisco 897VAMW router.

Figure 1-32 Back Panel of the Cisco 897VAMW Router

344770

1LEDs

7 6 GELAN 5 4

3 2 POE 1 0

GE WAN

54VDC 1.2A

12VDC 2.5A

VDSL/ADSL

overPOTS

CONSOLE

RESET

344772

1 2 34 7 89 10

5 6

1GE WAN interface 7On/Off switch

2SFP port 8Reset button

3USB port 9Earth ground connection

48-port Gigabit Ethernet switch110 Kensington security slot

5Console / Auxiliary port 11 VDSL / ADSL over POTS

6Power connector

1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with

the factory order, you must order and install it to enable the PoE function.

1-26

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Cisco 890 Series ISRs

Figure 1-33 shows the back panel of the Cisco 898EA router.

Figure 1-33 Back Panel of the Cisco 898EA Router

Caution The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN

port may occur if a non-RJ-45 connector is inserted.

Figure 1-34 shows the front panel of the Cisco 898EA router.

Figure 1-34 Front Panel of the Cisco 898EA Router

7 6 GELAN 5 4

3 2 POE 1 0

GE WAN

SFP

854VDC 1.2A

12VDC 2.5A

SHDSL

RJ45 ONLY

CONSOLE

RESET

Cisco 898EA

AUX

344774

1 2 34 7 89 10

5 6

1GE WAN interface 7On/Off switch

2SFP port 8Reset button

3USB port 9Earth ground connection

48-port Gigabit Ethernet switch1

1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with

the factory order, you must order and install it to enable the PoE function.

10 Kensington security slot

5Console / Auxiliary port 11 SHDSL (RJ45 Only)

6Power connector

344773

1LEDs

1-27

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

This section provides an overview of the following hardware features for the Cisco 860 series, 880

series, and 890 series ISRs. A feature summary is available at the end of this section.

• Kensington Lock

• Reset Button

• LEDs

• Memory

• USB Port

• Fan

• Power over Ethernet Module

• 3G Cellular Data WAN Connectivity

• Wireless LAN Connectivity

• Small Form-Factor Pluggable Port

• Feature Summary

Kensington Lock

A Kensington security slot is located on the router back panel. To secure the router to a desktop or other

surface, use the Kensington lockdown equipment.

Reset Button

The Reset button is used to restore the router to the factory default configurationor to load a custom

configuration file.

There are two different ways to do this:

1. by pressing the Reset button within 5 seconds of powering up the router; or

2. by pressing the Reset button for 5 seconds while running IOS.

Note If you execute a CLI reboot command while the embedded wireless AP is running Cisco Unified IOS

software, the router reboots, but the AP continues running. Clients with Cisco Unified IOS software are

controlled by a wireless LAN controller (WLC) and can be reset only by the controller.

Cisco 860VAE Routers—Custom Configuration File

On Cisco 860VAE routers, the reset button can be used to load a custom configuration file without having

to use the CLI. The configuration file can be located on an external USB flash drive or on the router's

compact flash.

1-28

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

The custom configuration file must be named one of the following:

• customer-config

• SN-customer-config

where “SN” is the unique hardware serial number.

When the system attempts to load a custom configuration file, configuration files on a USB flash drive

have priority over configuration files on the router's flash drive and the “SN-customer-config” file name

has priority over the “customer-config” file name. The priority for loading a configuration file is as

follows:

1. USB flash0: SN-customer-config

2. USB flash0: customer-config

3. Router flash: SN-customer-config

4. Router flash: customer-config

If the router does not find a valid custom configuration file, the system aborts the process.

To reset the router to the factory default configuration, follow these steps:

Step 1 Verify that IOS is running correctly by checking that the system status LED is on.

Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within

5 seconds.

The router reloads itself after the startup configuration has been replaced with the new customer

configuration.

Custom Configuration File for Cisco 892FSP, 896VA, 897VA, and Cisco 898EA

For the first method, the configuration file can be located on the router's compact flash or on the router's

nvram. The custom configuration file must use cfg as the filename extension.

When the system attempts to load a custom configuration file, configuration files on nvram have priority

over configuration files on the router's compact flash.

The priority for loading a configuration file is as follows:

1. nvram: *.cfg

2. Router flash: *.cfg

If the router does not find a valid custom configuration file, the system aborts the process.

1-29

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

To reset the router to the factory default configuration or to load a custom configuration file, follow these

steps:

Step 1 Turn the power on.

Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within

5 seconds.

The router reloads itself after the startup configuration has been replaced with the new customer

configuration.

For the second method, the configuration file can be located on an external USB flash drive or on the

router's compact flash.

The custom configuration file must be named one of the following:

• customer-config

• customer-config.SN ?

where "SN" is the unique hardware serial number.

When the system attempts to load a custom configuration file, configuration files on a USB flash drive

have priority over configuration files on the router's flash drive and the "customer-config.SN" file name

has priority over the customer-config file name.

The priority for loading a configuration file is as follows:

1. usbflash0:customer-config.SN

2. usbflash0:customer-config

3. Router flash:customer-config.SN

4. Router flash:customer-config

If the router does not find a valid custom configuration file, the system aborts the process.

To reset the router to the factory default configuration or to load a custom configuration file, follow these

steps:

Step 1 Verify that IOS is running correctly by checking that the system status LED is on.

Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within

5 seconds.

The router reloads itself after the startup configuration has been replaced with the new customer

configuration.

1-30

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

LEDs

The LEDs are located on the front panel of the router.

• Table 1-4 describes the LEDs for the Cisco 860 series, 880 series, and 890 series ISRs.

• Table 1-5 lists the LED descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and

Cisco 867VAE-K9 ISRs.

• Table 1-6 lists the LED description for the Cisco 892FSP ISR, 896VA, 897VA, and 898EA.

Ta b l e 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs

LED Color Description 860 Series 880 Series 890 Series

Power OK Green On—DC power is being supplied to the router and the

Cisco IOS software is running.

Blinking—Bootup is in process, or the router is in

Rommon monitor mode.

Off—Power is not supplied to the router.

All models All models All models

Link Status FE0 Green On—Ethernet port is connected.

Blinking—Data is either being received or being

transmitted.

Off—Ethernet port is not connected.

All models All models All models

Link Status FE1

Link Status FE2

Link Status FE3

Link Status FE4 Green On—Ethernet port is connected.

Blinking—Data is either being received or being

transmitted.

Off—Ethernet port is not connected.

— — All models

Link Status FE5

Link Status FE6

Link Status FE7

FE WAN Port

Link Status Green On—Port is connected.

Blinking—Data is either being received or being

transmitted.

Off—Port is not connected.

861

models 881

models All models

GE WAN Port

Link Status Green On—Port is connected.

Blinking—Data is either being received or being

transmitted.

Off—Port is not connected.

— — All models

WLAN

(2.4 GHz) Green On—Radio is connected, SSID1 is configured, and client

is associated, but no data is being received or being

transmitted.

Slow blinking—Radio is connected, SSID is configured,

and beacons are being transmitted.

Fast blinking—Data is either being received or being

transmitted.

Off—Radio is shut down, and no SSID is configured.

Wireless

models Wireless

models

1-31

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

WLAN (5 GHz) Green On—Radio is connected, SSID is configured, and client is

associated, but no data is being received or being

transmitted.

Slow blinking—Radio is connected, SSID is configured,

and beacons are being transmitted.

Fast blinking—Data is either being received or being

transmitted.

Off—Radio is shut down, and no SSID is configured.

—Wireless

models Wireless

models

WLAN LINK

(Autonomous

Mode)

Green On—Wireless link is up.

Blinking—Ethernet link is up, and data is either being

received or being transmitted.

Off—Wireless link is down.

Wireless

models Wireless

models

WLAN LINK

(Unified Mode) Green On—Ethernet link is up, and wireless access point (AP) is

communicating with LWAPP2 controller.

Blinking—Ethernet link is up, but wireless AP is not

communicating with LWAPP controller.

Off—Ethernet link is down.

—Wireless

models Wireless

models

PoE Green On—PoE is connected and powered.

Off—PoE is not installed.

—Models

with PoE Models

with PoE

Amber On—Fault with the PoE.

VPN Green On—VPN is connected. —All models All models

PPP3Green On—At least one PPP session is established. —All models All models

xDSL4 CD Green On—The xDSL interface is connected to the DSLAM5.

Blinking—Training to the line.

Off—Indicates that a connection has not been established

or the port is shut down.

—887,

887VA,

887VA-M8

888

models

896VA,

897VA,

898EA

xDSL Data Green Blinking—The xDSL interface is either receiving or

transmitting data.

Off—No data is being transmitted or being received.

—887,

887VA,

887VA-M8

88 models

896VA,

897VA,

898EA

xDSL ATM Green On—The router is operating in ATM6 mode.

Off—Not operating in ATM mode.

—888E —

xDSL EFM Green Blink—The router is operating in EFM7 mode.

Off—Not operating in EFM mode.

— — 898EA

Data BRI LINK Green On—ISDN D channel is connected. —887, 888

models 892

models

Data BRI B1 Green Blinking—B1 channel is either receiving or sending data,

or data is passing through ISDN channel 1. —887, 888

models 892

models

Table 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

LED Color Description 860 Series 880 Series 890 Series

1-32

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Data BRI B2 Green Blinking—B2 channel is receiving or sending data, or

data is passing through ISDN channel 2. —887, 887V,

888

models

892

models

3G8 WWAN9Green On—Service is established.

Slow Blinking—Searching for service.

Fast Blinking—Data is either being received or being

transmitted.

—3G models —

3G RSSI10 Green Off—Low signal strength (lower than -100 dBm).

On—High RSSI (-69 dBm or higher).

Slow Blinking—Low or medium RSSI (-99 to -90 dBm).

Fast Blinking—Medium RSSI (-89 to -70 dBm).

—3G models —

Amber On—No service. —3G models —

3G GSM11 Green On—Service is established.

Off—No service.

—3G models —

3G CDMA12 Green On—Service is established.

Off—No service.

—3G models —

FXO Voice Green On—FXO port is connected.

Blinking—FXO port is either receiving or transmitting

data.

—88113 —

BRI Voice LNK Green On—BRI interface is connected. — — —

BRI Voice B1 Green On—BRI B1 channel is connected.

Blinking—BRI B1 channel is either receiving or

transmitting data.

— — —

BRI Voice B2 Green On—BRI B2 channel is connected.

Blinking—BRI B2 channel is either receiving or

transmitting data.

— — —

FXS/DID Voice Green On—FXS/DID port is connected.

Blinking—FXS/DID port is either receiving or

transmitting data.

—SRST

models —

V.92 Modem Green On—Modem is connected.

Blinking—V.92 port is either receiving or transmitting

data.

— — 891

models

SFP14 EN Off Not present. — — 892F

models

Green Present and enabled. — —

Amber Present with failure. — —

SFP S Green Blinking—Blinking frequency indicates port speed. — — 892F

models

1. SSID = service set identifier.

Table 1-4 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

LED Color Description 860 Series 880 Series 890 Series

1-33

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Table 1-5 describes the LEDs for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco

867VAE-K9 ISRs.

2. LWAPP = Lightweight Access Point Protocol.

3. PPP = Point-to-Point Protocol.

4. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital

subscriber line).

5. DSLAM = digital subscriber line access multiplexer.

6. ATM = Asynchronous Transfer Mode.

7. EFM = Ethernet in the First Mile.

8. 3G = Third-Generation.

9. WWAN = wireless WAN.

10. RSSI = Received Signal Strength Indicator.

11. GSM = Global System for Mobile Communication.

12. CDMA = code division multiple access.

13. SRST = Survivable Remote Site Telephony.

14. SFP = small-form-factor pluggable.

Ta b l e 1-5 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs

LED Activity Description

Power/System Power/System LED: Solid

GE_MODE LED: Off

DSL_LINK LED: Off

Power is on and system running in the Rommon mode.

Note During the early booting stage, both Power/System, GE_MODE and

DSL_LINK LED will be turned on temporarily for the power on test.

DSL_LINK and GE_MODE LED will be turned off later after booting

into Rommon.

Power/System LED: Solid

GE_MODE LED: Solid

DSL_LINK LED: Off

IOS functioning in GE WAN mode.

Power/System LED: Solid

GE_MODE LED: Off

DSL_LINK LED: Solid or

flashing

IOS functioning in DSL_WAN mode.

Note In IOS DSL_WAN mode, DSL_LINK LED will be solid after DSL

training complete or flashing during training.

xDSL1 ACT Green On—DSL interface is up.

Blinking—DSL WAN activity (traffic in either direction).

Faster blinking—Heavier traffic

Off—Device is powered off or the DSL WAN interface is down.

xDSL Link Green On—DSL WAN Mode is selected and DSL training complete.

Blinking—DSL WAN Mode is selected but incomplete DSL Link Up state,

such as in-training, or controller “OFF,” or no cable attached to DSL connector.

Off—Device is powered off or GE WAN mode is selected.

1-34

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

GE ACT Green On—GE WAN interface is up.

Blinking—GE WAN activity (traffic in either direction).

Off—Device is powered off or GE WAN interface is down.

GE Mode Green On—GE WAN Mode is selected.

Off—Device is powered off or DSL WAN mode is selected.

1. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital

subscriber line).

Table 1-5 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs

LED Activity Description

1-35

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Table 1-6 describes the LEDs for the Cisco 892FSP.

Ta b l e 1-6 LED desciption for Cisco 892FSP ISR, 896VA, 897VA, and 898EA Routers

Shared LEDs on the Cisco 881-V and Cisco 887VA-V Voice and Data Routers

On the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W routers, the BRI1, BRI2 and the FXS ports

share LED indicators. The following ports share an LED indicator:

• BRI 1B1 channel and FXS 3

• BRI 1B2 channel and FSX 4

• BRI 2B1 channel and FXS 5

• BRI 2 B2 channel and FXS 6

LED Color Activity Description

PWR_OK Green Power Status Off—No power.

Steady on—Normal operation.

Blink—Boot up phase or in ROM Monitor mode.

GE0 Green/Amber Link Status Green On—Ethernet port is connected.

Amber On—Fault with PoE. There is a fault with

the inline power supply.

Green/Amber Blinking—Data is either being

received or being transmitted.

Green/Amber Off—Ethernet port is not

connected.

GE1

GE2

GE3

GE4

GE5 Green Link Status On—Ethernet port is connected.

Blinking—Data is either being received or being

transmitted.

Off—Ethernet port is not connected.

GE6

GE7

GE WAN ports Green Link Status On—Port is connected.

Blinking—Data is either being received or being

transmitted.

Off—No link.

SFP WAN

ports Green Link Status On—Port is connected.

Blinking—Data is either being received or being

transmitted.

Off—No link.

VPN_OK Green —Off—No tunnel.

Steady on—At least one tunnel is up.

PPP_OK Green —Off—No PPP session.

Steady on—At least one PPP established.

1-36

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Because the LED indicators are shared, the LED illuminates (green) when either port is active. For

example, the LED indicator labeled BRI 1 B1 illuminates when either the BRI1 B1 channel is active or

when the FXS port is active. You can determine the activity status on each interface by using the

following commands.

• For activity status on the FXS ports, use the show port summary command.

• For activity status on the BRI ISDN port, use the show isdn status command.

Figure 1-35 shows a close-up view of the LED indicators.

Figure 1-35 Close-up of the BRI and FXS LED Indicators

Memory

The Cisco 860 series, 880 series, and 890 series routers contain flash memory and main memory.

Flash Memory

The Cisco 860 series, 880 series, and 890 series ISRs use non-upgradable flash memory storage. The

onboard flash memory contains the Cisco IOS software image, the boot flash contains the ROMMON

boot code, and a separate non-volatile flash contains the cookie configuration.

Table 1-7 describes the default flash memory storage.

300149

Ta b l e 1-7 Flash Memory Storage

Models Flash Memory Storage

Cisco 860 series and 880 series routers 128 MB

Cisco 880 series voice routers and Cisco 890 series routers 256 MB

Cisco 880 series routers with embedded WLAN antennas 256 MB

Cisco 860VAE routers 8 MB boot flash, 128 MB for IOS

Cisco 860VAE-K9 64 MB boot flash and IOS

1-37

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Note Flash memory is not upgradable. An external USB flash memory module may be used if additional flash

memory is needed.

Main Memory

Table 1-8 describes the main onboard memory storage for different router models.

USB Port

Table 1-9 describes the USB ports for different router models.

Fan

Some router models do not have a fan, while other models have either one or two fans.

The fans spin at full speed, as a diagnostic aid, immediately after the router is powered up. After the

router has booted, the fans spin as fast as necessary to minimize fan noise while maintaining a safe

internal operating temperature.

Ta b l e 1-8 Main Onboard Memory Storage

Models Onboard Memory Storage Expandability

Cisco 860 series routers 256 MB Not expandable.

Cisco 860VAE series routers 256 MB Not expandable.

Cisco 880 series routers 256 MB

(expandable to 768 MB) A memory expansion slot accommodates

a PC2-4200, 256-MB or 512-MB double

data rate 2 (DDR2) SODIMM, for a

maximum of 768 MB.

Cisco 880 series routers with

embedded WLAN antennas 512 MB Not expandable.

Cisco 892FSP, 896VA,

897VA, 898EA routers 512 MB Expandable to 1 GB.

Ta b l e 1-9 USB Ports

Models USB

Cisco 860 series (non-VAE) No USB ports.

Cisco 860VAE series One USB 1.1-compliant port located on the back panel. The USB

port does not support eToken.

Cisco 880 series One USB 1.1-compliant port located on the front panel. The USB

port provides connection for USB devices such as security tokens

and flash memory.

Cisco 890 series1

1. Except for Cisco 892FSP, Cisco 896VA, Cisco 897VA, and Cisco 898EA.

Two USB 2.0-compliant ports located on the front panel.

Cisco 892FSP, Cisco 896VA,

Cisco897VA, Cisco 898EA One USB 2.0-compliant port located on the back panel.

1-38

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

The following models have no fan:

• Cisco 892FSP

• Cisco 896VA

• Cisco 897VA

• Cisco 898EA

Power Supply

The Cisco 892FSP has a single +12V power supply input. The Cisco 892FSP power connector is

different from the barrel-type connector on other 890 series models. The AC adapter cable connector

has four pins and a built-in locking mechanism. Figure 3-27 shows the power adapter connector.

The Cisco 896VA, 897VA, and Cisco 898EA use PoE (12 VDC 43 W, -54 VDC 80 W) and non-PoE

(12 VDC 60 W) power supplies.

Power over Ethernet Module

The Cisco 880 series ISRs can include an optional Power over Ethernet (PoE) module that provides

power to 802.3af-compliant devices connected to FE ports 0 and 1.

The Cisco 890 series ISRs can include an optional PoE module that provides power to 802.3af-compliant

devices connected to FE ports 0, 1, 2, and 3.

The PoE module is an option available only for the Cisco 880 series and 890 series ISRs and requires a

48 V external power adapter.

This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router

and inserting the PoE 48 V external power adapter.

Note The Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a

30 W power supply for non-POE-enabled routers or a 60 W power supply for POE-enabled routers. For

the back panels of some of these routers, see Figure 1-17 and Figure 1-19.

3G Cellular Data WAN Connectivity

The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS])

cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data

link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony

and broadband wireless data in a mobile environment.

Some Cisco 880G models come with a 34-mm express card slot ready for use with a commercial 3G card

radio. The 3G express card slot is located on the front panel. For a list of supported 3G cards, see the

Cisco 880 Series Integrated Services Routers Data Sheet.

Other Cisco 880G models come with embedded WAN modems for use over GSM or CDMA networks.

These routers have antenna connectors on the back panel. GSM routers have two SIM card slots. For

information on configuring Cisco 880 series ISRs for 3G, see Configuring Cisco EHWIC and 880G for

3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3.7G (HSPA+)/3.5G (HSPA).

1-39

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Wireless LAN Connectivity

The embedded Wi-Fi CERTIFIED™, 802.11a/b/g/n-compliant wireless AP is preinstalled in the router

as an optional feature. The Cisco 860 series routers support autonomous features and network

configurations. The Cisco 880 series and 890 series routers support both autonomous and unified

features and network configurations.

The wireless AP does not have an external Console port. Use the router’s Console port as described in

Chapter 3, “Connecting a Terminal or PC to the Console Port.” To configure the wireless device, use the

Cisco IOS command-line interface (CLI).

Table 1-10 describes the radios and antennas for the Cisco 860 series, 880 series, and 890 series routers.

Note Cisco 860VAE ISRs do not support wireless LAN connectivity.

The 5-GHz radio operates in the Unlicensed National Information Infrastructure (UNII) 1, 2, 3, 5-GHz

frequency bands.

Ta b l e 1-10 Wireless Device Radios and Antennas

Radio Module Platform Radio Band

Maximum Data

Throughput1

1. Actual data rate is highly dependent on your wireless environment.

Mode Antenna

Single-band

802.11b/g/n

draft 2.0 radio

module

Cisco 860 and 880 series

routers

Note Cisco 860VAE

ISRs do not

support wireless

LAN connectivity.

2.4 GHz Up to 100 Mb/s Cisco 860 series:

autonomous only

Cisco 880 series:

autonomous and

unified

Three captive,

omnidirectional dipole

antennas: 2 dBi at

2.4 GHz

Single-band

802.11b/g/n

radio module

Cisco 880 series routers

with embedded WLAN

antennas

2.4 GHz 100 Mb/s per radio,

up to 200 Mb/s

total

Autonomous and

unified Three embedded,

omnidirectional

antennas: 2 dBi at

2.4 GHz

Dual-band

802.11a/n and

802.11b/g/n

radio modules

2.4 GHz

and

5 GHz

Three embedded,

dual-band,

omnidirectional

antennas: 2 dBi at

2.4 GHz and 5 dBi at

5 GHz

Dual-band

simultaneous

802.11a/n and

802.11b/g/n

radio modules

Cisco 890 2.4 GHz

and 5 GHz 100 Mb/s per radio,

up to 200 Mb/s

total

Autonomous and

unified Three dual-band,

removable,

2.4-GHz/5-GHz

omnidirectional dipole

RP-TNC antenna2

2. The antennas require some minor installation. They must be screwed onto the RP-TNC antenna connectors on the I/O side of the chassis. See the following

document on Cisco.com for feature information: http://www.cisco.com/en/US/docs/routers/access/wireless/hardware/notes/antdip.html

1-40

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Supported Cisco Radio Antennas

The Cisco 891, Cisco 892, and Cisco 892F come with three removable dipole antennas that can be

replaced using the Cisco approved antenna extenders listed in Table 1-11.

Note Cisco supports only the antennas listed in Table 1-11 with the Cisco 890 series dual-band radio module.

Small Form-Factor Pluggable Port

The SFP port supports auto-media-detection, auto-failover, and remote fault indication (RFI), as

described in the IEEE 802.3ah specification.

See the Cisco 892F data sheet for a list of supported SFPs.

Ta b l e 1-11 Cisco Antennas Supported on the Cisco 890 Series ISRs

Cisco Part Number Antenna Type Maximum Gain Description

AIR-ANTM2050D-R Omnidirectional 2.0 dBi at 2.4 GHz

5.0 dBi at 5 GHz

This is the default antenna. It is a swivel-mount

dipole dual-band blade antenna. For more

information, see Cisco Multiband Swivel-Mount

Dipole Antenna (AIR-ANTM2050D-R).

AIR-ANTM4050V-R Omnidirectional 4.0 dBi at 2.4 GHz

5.0 dBi at 5 GHz

Ceiling-mount dual-band antenna. This antenna

has a clip that allows it to be mounted on a

drop-ceiling cross member. For more information,

see Cisco Multiband Diversity Omnidirectional

Ceiling-Mount Antenna.

AIR_ANTM5560P-R Patch 5.5 dBi at 2.4 GHz

6.0 dBi at 5 GHz

Wall-mount dual-band antenna. For more

information, see Cisco Multiband Wall-Mount,

Corner-Mount, or Mast-Mount Antenna.

1-41

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Feature Summary

Table 1-12 summarizes the hardware features available in the Cisco 860 series, Cisco 880 series, and

Cisco 890 series ISRs.

Ta b l e 1-12 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs

Feature Description 860 Series 880 Series 890 Series

Reset button Resets the router configuration to the factory default. All models All models All models

Resets the router configuration to customer configuration. 866VAE,

867VAE,

866VAE-K9,

867VAE-K9

— —

FE1 built-in

switch ports Provides connection to 10/100BASE-T (10/100-Mb/s)

Fast Ethernet networks. The autosensing function in these

routers eliminates the need for a crossover cable and enables

the router to detect MDI2 or MDIX3 in any other PC or hub

with a straight-through cable or a crossover cable.

All models All models 891, 892,

892F

GE4 built-in

switch port Provides connection to 10/100/1000BASE-T

(10/100/1000-Mb/s) Gigabit Ethernet networks. The

autosensing function in these routers eliminates the need for

a crossover cable and enables the router to detect MDI5 or

MDIX6 in any other PC or hub with a straight-through cable

or a crossover cable.

866VAE-K9,

867VAE-K9 —892FSP,

896VA,

897VA,

897VAM,

897VAW,

897VAMW,

898EA

Console or AUX

port Provides a connection to the terminal or PC for software

configuration or troubleshooting. The Console port may be

configured as a virtual auxiliary port for dial backup and

remote management.

Cisco 891, Cisco 892, and Cisco 892F have separate console

and auxiliary ports.

Cisco 892FSP has combined console and auxiliary port.

All models All models All models

Security features Provides support for VPNs7, Cisco IOS Firewall, and

IPSec8. The Cisco 880 series routers also provide URL

filtering.

861, 867,

866VAE-K9,

867VAE-K9

All models All models

Embedded

wireless AP Provides Wi-Fi CERTIFIED™ 802.11a/b/g/n compliance.

The Cisco 860 series routers contain a single 802.11b/g/n

radio.

Some Cisco 880 series routers contain a single 802.11b/g/n

radio while others contain dual 802.11a/n and 802.11b/g/n

radios.

The Cisco 890 series routers contain dual 802.11b/g/n and

802.11a/n radios.

Wireless

models

802.11b/g/n

Wireless

models

802.11b/g/n9

and

802.11a/n10

Wireless

models

802.11b/g/n

and

802.11a/n

FE WAN port Provides connection to 10/100BASE-T. Can be connected to

other network devices, such as a cable modem, an xDSL11

modem, or router. The router is capable of bridging and

multiprotocol routing between the LAN and WAN ports.

861 881 891, 892,

892F

1-42

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

GE WAN port 10/100/1000 GE WAN Port. 866VAE,

867VAE,

866VAE-K9,

867VAE-K9

—All models

VDSLoPOTS12

port Provides connection to a VDSL network. —887V —

ADSLoPOTS Provides ADSL connection over basic telephone service

with Annex A and Annex B ITU G. 992.1 (ADSL), G.992.3

(ADSL2), and G.992.5 (ADSL).

— — —

ADSLoISDN Provides ADSL connection over ISDN. — — —

DSL Multi-mode

(VDSL and

ADSL2/2+)

Provides ADSL2/2+ or VDSL connection over POTS or

ISDN (ISDN on 886VA only). 866VAE,

867VAE,

866VAE-K9,

867VAE-K9

886VA,

887VA,887V

A-M

892FSP,

896VA,

897VA,

897VAM,

897VAW,

897VAMW,

898EA

Real-time clock

(RTC) RTC provides nonvolatile date and time when the router is

powered on. The RTC is used for verifying the validity of the

Certification Authority stored on the router. It is backed up

by a nonreplaceable lithium battery.

866VAE,

867VAE,

866VAE-K9,

867VAE-K9

All models All models

USB port, Supports USB 1.1. Provides connection for USB devices

such as security tokens and flash memory.

The Cisco 880 series routers have a single USB port; the

Cisco 890 series routers have two USB ports.

Cisco 880 series routers with embedded WLAN antennas

have one USB 2.0 port.

Cisco 892FSP and Cisco 860VAE series routers have one

USB 2.0 port on the rear panel for temporary installation of

a Cisco-approved USB memory device for maintenance

purposes only. The port supports only USB 2.0. Refer to the

product datasheet for the list of supported USB flash

memory devices.

Note Cisco 860VAE series router USB port does not

support eToken.

866VAE,

867VAE,

866VAE-K9,

867VAE-K9

All models All models

PoE13 (Optional) Provides power for 802.3af-compliant devices

(such as phones) that are connected to the router.

The Cisco 880 series routers support a 2-port PoE module;

the Cisco 890 series routers support a 4-port PoE module.

—Models with

PoE Models with

PoE

G.SHDSL14 port Provides 2-wire or 4-wire connection to a G.SHDSL

network. —888 898EA

3G15 card slot Provides backup data link. —3G models —

Table 1-12 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

Feature Description 860 Series 880 Series 890 Series

1-43

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

Dying gasp Detects when the router is losing power, and sends a

power-fail signal to warn the DSLAM16 about the

impending line drop.

866VAE,

867VAE,

866VAE-K9,

867VAE-K9,

xDSL

models

888EA,

xDSL models

892FSP,

896VA,

897VA,

897VAM,

897VAW,

897VAMW,

898EA

Data BRI port Provides backup and remote management functions by

connecting to the ISDN service provider if the main VDSL

or G.SHDSL link fails.

—xDSL

models,

except for the

3G and

SRST17

models

892

V.92 modem Provides dial backup and remote management functions if

the main WAN link fails. — — 891

FXO18 port An FXO interface connects local calls to a central office or

PBX. This is the interface a standard telephone provides. —881 SRST —

FXS19/DID20

port An FXS interface connects directly to a standard telephone,

fax machine, or similar device. This interface supplies

ringing voltage and dial tone to the station.

—SRST models —

BRI voice port The ISDN BRI S/T voice interface provides a client-side

(TE) ISDN S/T physical interface for connection to an NT1

device that terminates an ISDN telephone network.

—887V —

SFP21 port Supports auto-media-detection, auto-failover, and remote

fault indication (RFI), as described in the IEEE 802.3ah

specification.

See the Cisco 892F data sheet for a list of supported SFPs.

— — 892F

models,

892FSP,

896VA,

897VA,

897VAM,

897VAW,

897VAMW,

898EA

1. FE = Fast Ethernet.

2. MDI = media-dependent interface in normal mode.

3. MDIX = media-dependent interface in crossover mode.

4. GE = Gigabit Ethernet.

5. MDI = media-dependent interface in normal mode.

6. MDIX = media-dependent interface in crossover mode.

7. VPN = Virtual Private Network.

8. IPsec = IP security.

9. This applies to most models of the Cisco 880 series routers.

10. This applies to Cisco 880 series routers with embedded, wireless antennas.

11. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line), VDSL (very-high-data-rate digital

subscriber line), and G.SHDSL.

12. VDSLoPOTS = very-high-data-rate digital subscriber line 2 over plain old telephone service.

13. PoE = Power over Ethernet. This function can be added to an 880 or 890 series router by installing the PoE adapter card in the router and inserting the

PoE 48-V external power adapter.

Table 1-12 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued)

Feature Description 860 Series 880 Series 890 Series

1-44

Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide

OL-16215-10

Chapter 1 Product Overview

Hardware Features

14. G.SHDSL = (global industry standard) symmetrical high-speed DSL.

15. 3G = Third-Generation.

16. DSLAM = digital subscriber line access multiplexer.

17. SRST = Survivable Remote Site Telephony.

18. FXO = Foreign Exchange Office.

19. FXS = Foreign Exchange Station.

20. DID = Direct Inward Dialing.

21. SFP = small-form-factor pluggable.

GemTek Technology CISCO867VAE XDSL Router User Manual HIG880 860

Gemtek Technology Co., Ltd. XDSL Router HIG880 860

Contents

User Manual Part 1

Navigation menu

Namespaces

Views

Navigation