GemTek Technology CISCO867VAE XDSL Router User Manual 800srcsi Gemtek

Gemtek Technology Co., Ltd. XDSL Router 800srcsi Gemtek

UserManual.wiki >

GemTek Technology >

CISCO867VAE User Manual >

User Manual Statements Part 1 HTML Version

User Manual Statements Part 1

Americas Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Regulatory Compliance and Safety Information

for Cisco 800 Series Routers

Revised: May 2, 2013, OL-10260-06

This document provides international regulatory and safety compliance information for Cisco 800 series

routers. Use this document with the other publications for the Cisco 800 series router you have

purchased. The “Product Scope” section on page 82 indicates the models covered in this document.

This document contains the following sections:

• Electromagnetic Compatibility, page 1

• Telecommunications, page 5

• Radio, page 7

• Cellular Products, page 14

• Declarations of Conformity, page 14

• CE Marking, page 14

• European Union Statements, page 18

• Environmental Compliance, page 15

• Translated Safety Warnings, page 15

• Product Scope, page 82

• Obtaining Documentation and Submitting a Service Request, page 88

Electromagnetic Compatibility

This section describes electromagnetic compatibility (EMC) compliance conditions. It contains the

following:

• EMC Class A, page 2

• EMC Class B, page 3

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Electromagnetic Compatibility

Statement 210

Two people are required to lift the chassis. Grasp the chassis underneath the lower edge and lift with both

hands. To prevent injury, keep your back straight and lift with your legs, not your back.

EMC Class A

This section includes the following EMC Class A warnings:

• Statement 2017—Class A Notice for FCC

• CISPR 22 Class A Statement

• Statement 2021—Class A Notice for Canada

• Statement 191—VCCI Class A Warning for Japan

• Statement 2005 for China

• Statement 294 for Korea

• Statement 2012 for Korea

• Statement 2014 for Russia

• Statement 257 for Taiwan

Statement 2017—Class A Notice for FCC

Modifying the equipment without Cisco's authorization may result in the equipment no longer

complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use

the equipment may be limited by FCC regulations, and you may be required to correct any interference

to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

CISPR 22 Class A Statement

This equipment complies with the requirements of CISPR 22 (EN 55022) for Class A Information

Technology Equipment (ITE).

Warning

This is a class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

Statement 2021—Class A Notice for Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Electromagnetic Compatibility

Statement 191—VCCI Class A Warning for Japan

EMC Class B

This section includes the following EMC Class B warnings:

• Statement 2018—Class B Notice for FCC

• CISPR 22 Class B Statement

• Canada Compliance Statements

• Australia Compliance Statement

• Statement 295 for Korea

• Statement 2016 for Taiwan

• Statement 157—VCCI Compliance for Class B Equipment

Statement 2018—Class B Notice for FCC

Modifying the equipment without Cisco’s authorization may result in the equipment no longer

complying with FCC requirements for Class B digital devices. In that event, your right to use the

equipment may be limited by FCC regulations, and you may be required to correct any interference to

radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

Warning

This is a Class A product based on the standard of the VCCI Council. If this equipment is used in a

domestic environment, radio interference may occur, in which case, the user may be required to take

corrective actions.

VCCI-A

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Electromagnetic Compatibility

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

CISPR 22 Class B Statement

Emissions:

This equipment complies with the requirements of CISPR 22 (EN 55022) for Class B Information

Technology Equipment (ITE).

Canada Compliance Statements

Statement 2022—Class B Notice for Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Australia Compliance Statement

Network connected equipment is approved to the Australian and New Zealand Safety and EMC

requirements by Cisco Systems Incorporated which is a Recognized Laboratory by ACA and New

Zealand. Stand-alone power supply modules provided with this equipment are separately approved by

an Australian State designated Electricity Authority.

Statement 157—VCCI Compliance for Class B Equipment

Warning

This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or

television receiver in a domestic environment, it may cause radio interference. Install and use the

equipment according to the instruction manual.

VCCI-B

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Telecommunications

This section describes telecommunications compliance. It contains the following:

• Statement 3023—Equipment That Complies With 47 CFR Part 68

• Industry Canada Notice

• Statement 3017

Statement 3023—Equipment That Complies With 47 CFR Part 68

This equipment complies with Part 68 of the FCC rules and the requirements adopted by ACTA. On the

bottom of the equipment is a label that contains, among other information, a product identifier in the

format, US:AAAAANNAAAAAAA. If requested, this number must be provided to the telephone

company.

Applicable connector jack Universal Service Order Codes (“USOC”) for the Equipment is RJ11.

A plug and jack used to connect this equipment to the premises wiring and telephone network must

comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant

telephone cord and modular plug is provided with this product. It is designed to be connected to a

compatible modular jack that is also compliant. See installation instructions for details.

The REN is used to determine the number of devices that may be connected to a telephone line.

Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming

call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number

of devices that may be connected to a line, as determined by the total RENs, contact the local telephone

company. For products approved after July 23, 2001, the REN for this product is part of the product

identifier that has the format US:AAAAANNAAAAAAA. The digits represented by 01 are the REN

without a decimal point.

If this Router causes harm to the telephone network, the telephone company will notify you in advance

that temporary discontinuance of service may be required. If advance notice is not practical, the

telephone company will notify the customer as soon as possible. Also, you will be advised of your right

to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operation, or procedures that

could affect the operation of this equipment. If this happens, the telephone company will provide

advance notice in order for you to make the necessary modifications to maintain uninterrupted service.

If trouble is experienced with this Router, for repair or warranty information, please contact Cisco

Systems, Inc. – address: 170 West Tasman Dr. San Jose, CA95134 USA, phone number: 1 408 526 4000.

If the equipment is causing harm to the telephone network, the telephone company may request that you

disconnect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission,

public service commission or corporation commission for information.

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation

of this equipment does not disable your alarm equipment. If you have questions about what will disable

alarm equipment, consult your telephone company or a qualified installer.

WHEN PROGRAMMING EMERGENCY NUMBERS AND/OR MAKING TEST CALLS TO

EMERGENCY NUMBERS:

1. Remain on the line and briefly explain to the dispatcher the reason for the call.

2. Perform such activities in the off-peak hours, such as early morning or late evenings.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Telecommunications

The facility interface and service order codes for Cisco 800 series routers are shown in Table 1.

Industry Canada Notice

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.

This is confirmed by the registration number. The abbreviation, IC, before the registration number

signifies that registration was performed based on a Declaration of Conformity indicating that Industry

Canada technical specifications were met. It does not imply that Industry Canada approved the

equipment.

The Ringer Equivalence Number (REN) for this terminal equipment is 01. The REN assigned to each

terminal equipment provides an indication of the maximum number of terminals allowed to be connected

to a telephone interface. The termination on an interface may consist of any combination of devices

subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does

not exceed five.

Le présent matériel est conforme aux spécifications techniques applicables d'Industrie Canada. Cette

conformité est confirmée par le numéro d'enregistrement. Le sigle IC, placé devant le numéro

d'enregistrement, signifie que l’enregistrement s’est effectué conformément à une déclaration de

conformité et indique que les spécifications techniques d'Industrie Canada ont été respectées. Il

n’implique pas qu’Industrie Canada a approuvé le matériel.

L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 01. L'IESassigné à chaque

dispositif terminal indique le nombre maximal de terminaux qui peuvent êtreraccordés à une interface

téléphonique. La terminaison d'une interface peut consister en unecombinaison quelconque de

dispositifs, à la seule condition que la somme d'indicesd'équivalence de la sonnerie de tous les dispositifs

n'excède pas 5.

Statement 3017

VoIP and Emergency Calling Services Do Not Function if Power Fails.

Ta b l e 1 Facility Interface and Service Order Codes

Port Type

Facility Interface

Code

Service Order

Code Jack Type

ISDN BRI S/T 02IS5 6.0N RJ-49C

ISDN BRI U 02IS5 6.0N RJ-49C

DSU 56K 04DU5-56 6.0N RJ-48S

ADSL Metallic —RJ-11C

SHDSL Metallic —RJ-14C

FXO 02LS2 None RJ-11C

FXO 02GS2 None RJ-21X

DID 02RV2.T AS.2 RJ-11C

Analog Modem 02LS2 None RJ-11C

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Radio

This section describes radio compliance conditions. It contains the following:

• 2.4 GHz Radio

• 5 GHz Radio

• Radio: Statements and Additional Information

• Cautions Relevant to 5 GHz Radio

• Power Level Settings

• RF Exposure

• Statement 372—Wireless LAN Products

• Statement 391—Low-Power Radio Data Communications Systems (ARIB-STD)

• Canadian Compliance Statement

• Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European

Community, Switzerland, Norway, Iceland and Liechtenstein

• Wireless Devices with IEEE 802.11a/b/g Radios

2.4 GHz Radio

The product bears the following WiFi certification mark:

5 GHz Radio

The product bears the following WiFi certification mark:

Radio: Statements and Additional Information

Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this

frequency when using the integrated antennas. Any changes or modification to the product not expressly

approved by Cisco could void the user’s authority to operate this device.

Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to

certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate

Compliance.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Radio

Statement 4000

The use of wireless devices in hazardous locations is limited to the constraints posed by the safety

directors of such environments. The use of a portable device may be restricted in some locations.

Statement 4001

The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.

Statement 4024

The use of software or firmware not supported/provided by the manufacturer may result that the

equipment is no longer compliant with the regulatory requirements.

United States

Statement 4002

The Part 15 radio device operates on a non-interference basis with other devices operating in this

frequency band as well as other services operating throughout the radio spectrum. Any changes or

modifications to the said product without approval from Cisco could void the user’s authority to operate

the device. This includes the use on non-approved antennas or 3rd party amplifiers with the radio

module.

Statement 4003

For Part 15.407 devices:

Caution Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the U-NII devices are restricted to

indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System

(MSS) operations.

Statement 4047

The radio has been evaluated under FCC Bulletin OET 65C (01-01) and found compliant to the

requirements as set forth in CFR 47 Sections 2.1091 and 15.247 (b) (4) addressing RF Exposure from

radio frequency devices.

To maintain compliance, the minimum separation distance from the antenna to general bystander is

20 cm (7.9 inches).

Canada

Statement 4046

The radio has been evaluated in accordance with RSS-102 addressing RF Exposure from radio frequency

devices and the product meets the requirements of Canada Health Code 6. To maintain compliance, the

minimum separation distance from the antenna to general bystander is 20 cm (7.9 inches).

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Radio

Radiation Exposure Statement

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body.

Cautions Relevant to 5 GHz Radio

FCC Guidelines for Installation and Operation of Outdoor Wireless LAN Devices

See New FCC Guidelines for Installation and Operation of Outdoor Wireless LAN devices (“U-NII

devices”) Operating in the 5470-5725-MHz Band at the following site:

http://www.cisco.com/en/US/prod/collateral/routers/ps272/data_sheet_c78-647116_ps11451_Products

_Data_Sheet.html

Statement 372—Wireless LAN Products

All wireless LAN products in the 5.2/5.3GHz band cannot be used outdoors. Use the product only

indoors.

Power Level Settings

Table 2 lists the maximum power level settings permissible for the radio modules.

RF Exposure

The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and

15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating

Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The

equipment should be installed more than 20 cm (7.9 in.) from your body or nearby persons. The access

point must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other

Ta b l e 2 Maximum Rated Power Output for the Radios

Radio FCC ID

Maximum Power Setting (dBM)

802.11a 802.11b (2.4 GHz) 802.11g (2.4 GHz) 802.11n (2.4, 5 GHz)

LDKXSNIACG13 —19 17 —

MCL74487504 —17 15 16

MCL74487604 16 17 15 15

LDKTG2050 15 17 15 16

MCL74751901 —17 15 16 (2.4 GHz only)

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Radio

FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not

approved by the FCC cannot be co-located with the access point. The access point’s co-located 2.4 GHz

integrated antennas support a minimum separation distance of 8 cm (3.2 in.) and are compliant with the

applicable FCC RF exposure limit when transmitting simultaneously.

Note Dual antennas used for diversity operation are not considered co-located.

Statement 391—Low-Power Radio Data Communications Systems (ARIB-STD)

This equipment shares a frequency band with a wide range of equipment: e.g. industrial, scientific, and

medical equipment such as microwave ovens, premises radio station (radio stations requiring licenses),

and specified low-power radio stations (radio stations not requiring licenses) for RFID used for factory

production lines as well as amateur radio stations (radio stations requiring licenses).

1. Before use, confirm that no premises radio stations and specified low-power radio stations for RFID

or amateur radio stations operate in your vicinity.

2. In the event that this equipment causes harmful interference to any premises radio station for RFID,

immediately change frequencies or halt radio wave emission and contact us at the information

indicated below for consultation on interference avoidance measures (e.g. partition installation).

3. Contact us at the information indicated below URL if this equipment causes harmful interference to

any specified low-power radio stations for RFID or amateur radio stations or if other problems arise.

Canadian Compliance Statement

Cisco 2.4-GHz and 5-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz

spread spectrum devices. The use of this device in a system operating either partially or completely

outdoors may require the user to obtain a license for the system according to the Canadian regulations.

For further information, contact your local Industry Canada office.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Radio

Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the

European Community, Switzerland, Norway, Iceland and Liechtenstein

This section contains compliance information relevant to the European Union and other countries that

have implemented the EU Directive 1999/5/EC.

The information contained in this section applies to the following wireless LAN products:

English:

This equipment is in compliance with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

[Bulgarian]:

[Czech]:

Dansk

[Danish]:

Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i

Direktiv 1999/5/EF.

Deutsch

[German]:

Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprechenden

Vorgaben der Richtlinie 1999/5/EU.

Eesti

[Estonian]:

See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele asjakohastele sätetele.

Español

[Spanish]:

Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directiva

1999/5/CE.

[Greek]:

Français

[French]:

Cet appareil est conforme aux exigences essentielles et aux autres dispositions pertinentes de la

Directive 1999/5/EC.

Íslenska

[Icelandic]:

Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar 1999/5/EC.

Italiano

[Italian]:

Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva

1999/5/CE.

Latviski

[Latvian]:

[Lithuanian]:

Nederlands

[Dutch]:

Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde bepalingen van de

Richtlijn 1999/5/EC.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Radio

Wireless Devices with IEEE 802.11a/b/g Radios

This equipment is limited for indoor use.

Statement 392—Device is Prohibited for Outdoor Operations Within the 5.25–5.35 GHz Band

To avoid radio interference, this device is prohibited for outdoor operations within the 5.25–5.35 GHz

band. (for unit covers 5.25–5.35 GHz, on both unit and manual)

Administrative Rules for Low-power Radio-frequency Devices (for all wireless unit, on manual)

Article 12 For those low-power radio-frequency devices that have already received a type-approval,

companies, business units or users should not change its frequencies, increase its power or change its

original features and functions.

Malti

[Maltese]:

Magyar

[Hungarian]:

Norsk

[Norwegian]:

Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i

EU-direktiv 1999/5/EF.

Polski

[Polish]:

Português

[Portuguese]:

Este equipamento está em conformidade com os requisitos essenciais e outras provisões relevantes

da Directiva 1999/5/EC.

[Romanian]:

Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi relevante ale

Directivei 1999/5/EC.

Slovensko

[Slovenian]:

Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji Direktive 1999/5/EC.

Slovensky

[Slovak]:

Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými nariadeniami direktív:

1999/5/EC.

Suomi

[Finnish]:

Svenska

[Swedish]:

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Radio

Article 14 The operation of the Low-power Radio-frequency Devices is subject to the conditions that no

harmful interference is caused to aviation safety and authorised radio station; and if interference is

caused, the user must stop operating the device immediately and can’t re-operate it until the harmful

interference is clear.

The authorised radio station means a radio-communication service operating in accordance with

COMMUNICATION ACT.

The operation of the Low-power Radio-frequency Devices is subject to the interference caused by the

operation of an authorised radio station, by another intentional or unintentional radiator, by industrial,

scientific and medical (ISM) equipment, or by an incidental radiator.

Low-power Radio-frequency Devices Technical Specifications (for unit covers 5.25–5.35 GHz, on

manual)

4.7 Unlicensed National Information Infrastructure

4.7.5 Within the 5.25–5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce

any potential for harmful interference to co-channel MSS operations.

4.7.6 The U-NII devices shall accept any interference from legal communications and shall not interfere

the legal communications. If interference is caused, the user must stop operating the device immediately

and can’t re-operate it until the harmful interference is clear.

4.7.7 Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an

emissionis maintained within the band of operation under all conditions of normal operation as specified

in the user manual.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Cellular Products

Statement 4004

Any unauthorized changes or modifications to the radio without approval from Cisco may void the user's

authority to operate the device under certain parts of the FCC rules.

This device has been certified in accordance with 47 code of Federal Regulations Part 2 and FCC

Parts 22, 24, and 27.

Statement 4005

The system operator is responsible for obtaining any operators license, performing any required

frequency notification or meeting any qualification to operate this system under this rule part. This

device operates under the authority of a licensed radio service under 47 Code of Federal Regulations

Parts 22, 24, and 27.

Declarations of Conformity

The Declaration of Conformity statements for this product can be found at the following URL:

http://www.ciscofax.com

Note If you still have questions regarding the compliance of these products or you cannot find the information

you are looking for, please send an e-mail request to complianceinfo@cisco.com.

CE Marking

Products Using 5 GHZ Radio

This product bears the CE mark in accordance with Annex VII of Directive 1999/5/CE.

The following CE mark and class-2 identifier are affixed to the equipment and packaging:

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

European Union Statements

Products Without 5 GHZ Radio

This product bears the CE mark in accordance with Annex VII of Directive 1999/5/CE.

European Union Statements

The following statements apply in the European Union (EU).

• Network Termination Point Statement

• ISDN S/T Ports Statement

Network Termination Point Statement

This product does not contain a “Network Termination Point” (NTP) as defined by ETSI 300 386-2. This

product is classified by the manufacturer as “Terminal Equipment.” If you have any additional questions,

please contact your local network operator.

ISDN S/T Ports Statement

These ports have not been classified as “directly connected ports” to outside cables as defined by

CISPR 24, 1997 by the manufacturer. If you have any additional questions, please contact your local

network operator.

Environmental Compliance

The following statement(s) address environmental compliance.

• Statement 6005—California Perchlorate Contamination Prevention Act (Title 22, California Code

of Regulations, Chapter 33)

Statement 6005—California Perchlorate Contamination Prevention Act

(Title 22, California Code of Regulations, Chapter 33)

The battery inside this product might contain perchlorate, a known hazardous substance, so special

handling and disposal of this product might be necessary. For more information about perchlorate

and best management practices for perchlorate-containing substances, see

http://www.dtsc.ca.gov/HazardousWaste/Perchlorate/index.cfm.

Translated Safety Warnings

This section contains the translations of the following warning statements. A warning means danger. You

are in a situation that could cause bodily injury. Before working on equipment, be aware of the hazards

involved with electrical circuitry and standard safety practices to prevent accidents.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

• Statement 1071—Warning Definition

• Statement 19—TN Power Warning

• Statement 23—ISDN Connection Warning

• Statement 43—Jewelry Removal Warning

• Statement 94—Wrist Strap Warning

• Statement 119—Unit Short Circuit Protection

• Statement 150—Power Off Before Working on System

• Statement 151—ISDN Network Voltages Warning

• Statement 162—EU Public Network Port Warning

• Statement 199—Emergency Access Warning

• Statement 242—Equipment Grounding Warning

• Statement 332—Antenna Installation Warning

• Statement 353—This Product Must be Connected

• Statement 371—Power Cable and AC Adapter

• Statement 373—Must Connect To An Indoor Antenna

• Statement 378—Read Wall-Mounting Instructions Before Installation

• Statement 393—Explosive Device Proximity Wireless Network Device

• Statement 1004—Installation Instructions

• Statement 1005—Circuit Breaker

• Statement 1008—Class 1 Laser Product

• Statement 1010—Staring into Laser Beam

• Statement 1015—Battery Handling

• Statement 1016—Invisible Laser Radiation

• Statement 1021—SELV Circuit

• Statement 1023—No. 26 AWG

• Statement 1024—Ground Conductor

• Statement 1025—Use Copper Conductors Only

• Statement 1026—WAN Port Static Shock

• Statement 1028—More Than One Power Supply

• Statement 1030—Equipment Installation

• Statement 1031—EU Public Network Port

• Statement 1033—SELV-IEC 60950 DC Power Supply

• Statement 1035—Proximity to Water

• Statement 1036—Telephone Jacks in Wet Locations

• Statement 1037—Uninsulated Wires or Terminals

• Statement 1038—Telephone Use During an Electrical Storm

• Statement 1040—Product Disposal

• Statement 1042—Ring Signal Generator

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

• Statement 1046—Installing or Replacing the Unit

• Statement 1052—Installing and Grounding the Antenna

• Statement 1056—Unterminated Fiber Cable

• Statement 1057—Hazardous Radiation Exposure

• Statement 1072—Shock Hazard from Interconnections

• Statement 1073—No User-Serviceable Parts

• Statement 1074—Comply with Local and National Electrical Codes

• Statement 1077—Do Not Operate Unit Without Covers

• Statement 1088—Avoid Servicing Outdoor Connections During an Electrical Storm

Statement 1071—Warning Definition

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you

work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar

with standard practices for preventing accidents. Use the statement number provided at the end of

each warning to locate its translation in the translated safety warnings that accompanied this

device.

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan

veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij

elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard

praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de

waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt

raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin

käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu

onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen

mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien

lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant

entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez

conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures

couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,

référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen

kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und

den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder

Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle

persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli

relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le

traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du

begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med

elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten

av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne

enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de

lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos

perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de

prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para

localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular

cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los

procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el

número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña

a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och

känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av

varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna

anordning.

SPARA DESSA ANVISNINGAR

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões

corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os

circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o

número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de

segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

Advarsel

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for

legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de

involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til

undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de

oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 19—TN Power Warning

Warning

The device is designed to work with TN power systems.

Waarschuwing

Het apparaat is ontworpen om te functioneren met TN energiesystemen.

Varoitus

Koje on suunniteltu toimimaan TN-sähkövoimajärjestelmien yhteydessä.

Attention

Ce dispositif a été conçu pour fonctionner avec des systèmes d'alimentation TN.

Warnung

Das Gerät ist für die Verwendung mit TN-Stromsystemen ausgelegt.

Avvertenza

Il dispositivo è stato progettato per l’uso con sistemi di alimentazione TN.

Advarsel

Utstyret er utfomet til bruk med TN-strømsystemer.

Aviso

O dispositivo foi criado para operar com sistemas de corrente TN.

¡Advertencia!

El equipo está diseñado para trabajar con sistemas de alimentación tipo TN.

Varning!

Enheten är konstruerad för användning tillsammans med elkraftssystem av TN-typ.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 23—ISDN Connection Warning

Warning

The ISDN connection is regarded as a source of voltage that should be inaccessible to user contact.

Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or

connection hardware. Any hardwired connection (other than by nonremovable,

connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers.

Waarschuwing

De verbinding met ISDN (Integrated Services Digital Network = Digitaal netwerk met geïntegreerde

faciliteiten) wordt beschouwd als een spanningsbron die ontoegankelijk dient te zijn voor

gebruikers. Gebruikers dienen geen poging te doen om door de openbare telefoondienst (PTT)

verstrekte apparatuur of aansluitingshardware te openen of ermee te knoeien. Alle vastbedrade

verbindingen (behalve die verbindingen die gemaakt zijn door een niet-verwijderbare, slechts

eenmaal te verbinden stekker) dienen slechts door PTT-personeel of door daartoe opgeleide

ingenieurs gemaakt te worden.

Varoitus

ISDN-liitäntää pidetään jännitelähteenä, jonka kanssa käyttäjän ei tulisi päästä kosketuksiin.

Käyttäjien ei tulisi yrittää peukaloida tai avata laitteita tai liittimiä, jotka kuuluvat yleiselle

puhelinlaitokselle (PTO). Ainoastaan yleisen puhelinlaitoksen henkilökunnan tai ammattitaitoisten

teknikoiden tulee tehdä kaapeliliitännät (lukuun ottamatta kiinteitä pistokkeita, jotka yhdistetään

ainoastaan yhden kerran).

Attention

La connexion du réseau numérique intégré (Integrated Services Digital Network ou ISDN) constitue

une source de tension qui ne doit pas être accessible à l'utilisateur. Les utilisateurs ne doivent

jamais tenter de modifier ni même d'ouvrir un matériel fourni par une compagnie de téléphone

public, ou le matériel de connexion. Toute connexion câblée (autre que celles établies par une prise

non démontable à connexion unique) ne doit être effectuée que par le personnel de la compagnie de

téléphone ou par des techniciens proprement formés.

Warnung

Die ISDN-Verbindung gilt als eine Spannungsquelle, die dem Anwender unzugänglich sein sollte.

Anwender sollten nicht versuchen, sich an der von den Anbietern öffentlicher TK-Dienste

gelieferten Ausstattung oder Verbindungs-Hardware zu schaffen zu machen oder sie zu öffnen. Alle

festverdrahteten Verbindungen (mit Ausnahme der Verbindungen mit einem nicht abnehmbaren, nur

einmal anzuschließenden Stecker) sind von Mitarbeitern des TK-Anbieters oder von entsprechend

geschulten Technikern herzustellen.

Avvertenza

Il collegamento ISDN (Integrated Services Digital Network - Rete digitale a servizi integrati) viene

considerato come una fonte di tensione che dovrebbe essere inaccessibile al contatto dell’utente.

Gli utenti non devono né manomettere né provare ad aprire le apparecchiature o i dispositivi di

collegamento forniti dalla società telefonica. Qualsiasi collegamento cablato (ad eccezione di una

spina non rimovibile, da installare una sola volta) deve essere eseguito esclusivamente da un

dipendente della società telefonica o da tecnici specializzati.

Advarsel

ISDN-koblingen betraktes som en spenningskilde som bør være utilgjengelig for brukeren. Brukere

bør ikke klusse med eller åpne utstyr eller tilkoblingsmateriale som er utstyrt av Telenor. Eventuelle

faste installasjoner (bortsett fra koblinger som er foretatt med et støpsel for engangsbruk og som

ikke kan fjernes) må kun utføres av Telenor-montører.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Aviso

A conexão RDIS (Rede Digital com Integração de Serviços) é interpretada como uma fonte de tensão

que deverá ser inacessível ao utilizador. Os utilizadores não deverão tentar violar qualquer

equipamento ou conexão de serviço telefónico público. Qualquer conexão de rede de fios (para

além daquela estabelecida por uma ficha não-removível de ligação única), deverá apenas ser

efectuada por pessoal dos serviços telefónicos ou engenheiros devidamente treinados.

¡Advertencia!

La conexión al circuito RDSI (Red Digital de Servicios Integrados) se considera como una fuente de

voltaje con la cual el usuario no debe entrar en contacto. Los usuarios deberán evitar manipular

indebidamente, o abrir, los equipos o hardware de conexión proporcionados por cualquier

compañía operadora de la red pública de telefonía. Las conexiones de cable rígido que sean

necesarias (excepto las de clavija no desmontable de un solo uso) deberán ser realizadas

exclusivamente por personal de la entidad operadora de la red pública de telefonía, o por personal

técnico adecuadamente capacitado.

Varning!

ISDN-anslutningen betraktas som en spänningskälla och bör inte vara åtkomlig för användaren

(ISDN: Integrated Services Digital Network = digitalt flertjänstnät). Användare får inte manipulera

eller söka öppna utrustning eller anslutningsdon som tillhandahållits av telefonbolag

(PTO-produkter). Anslutning av ledningar (med undantag av en icke löstagbar propp för

engångsanslutning) får endast utföras av PTO-anställda eller lämpligt utbildade tekniker.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 43—Jewelry Removal Warning

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings,

necklaces, and watches). Metal objects will heat up when connected to power and ground and can

cause serious burns or weld the metal object to the terminals.

Waarschuwing

Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief

ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met

stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen

voorwerp aan de aansluitklemmen lassen.

Varoitus

Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut

(sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat

yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata

metalliesineet kiinni liitäntänapoihin.

Attention

Avant d’accéder à cet équipement connecté aux lignes électriques, ôter tout bijou (anneaux,

colliers et montres compris). Lorsqu’ils sont branchés à l’alimentation et reliés à la terre, les objets

métalliques chauffent, ce qui peut provoquer des blessures graves ou souder l’objet métallique aux

bornes.

Warnung

Vor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschließlich

Ringe, Ketten und Uhren) abnehmen. Metallgegenstände erhitzen sich, wenn sie an das Netz und die

Erde angeschlossen werden, und können schwere Verbrennungen verursachen oder an die

Anschlußklemmen angeschweißt werden.

Avvertenza

Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi

monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando

sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo

può saldarsi ai terminali.

Advarsel

Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal arbeide på utstyr som er

koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir svært varme

og kan forårsake alvorlige brannskader eller smelte fast til polene.

Aviso

Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as jóias que

estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos aquecerão em contacto com

a corrente e em contacto com a ligação à terra, podendo causar queimaduras graves ou ficarem

soldados aos terminais.

¡Advertencia!

Antes de operar sobre equipos conectados a líneas de alimentación, quitarse las joyas (incluidos

anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentación

y a tierra, lo que puede ocasionar quemaduras graves o que los objetos metálicos queden soldados

a los bornes.

Varning!

Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar på utrustning som

är kopplad till kraftledningar. Metallobjekt hettas upp när de kopplas ihop med ström och jord och

kan förorsaka allvarliga brännskador; metallobjekt kan också sammansvetsas med kontakterna.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 94—Wrist Strap Warning

Warning

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

touch the backplane with your hand or any metal tool, or you could shock yourself.

Waarschuwing

Draag tijdens deze procedure aardingspolsbanden om te vermijden dat de kaart beschadigd wordt

door elektrostatische ontlading. Raak het achterbord niet rechtstreeks aan met uw hand of met een

metalen werktuig, omdat u anders een elektrische schok zou kunnen oplopen.

Varoitus

Käytä tämän toimenpiteen aikana maadoitettuja rannesuojia estääksesi kortin vaurioitumisen

sähköstaattisen purkauksen vuoksi. Älä kosketa taustalevyä suoraan kädelläsi tai metallisella

työkalulla sähköiskuvaaran takia.

Attention

Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges

électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier

directement avec la main ni avec un outil métallique.

Warnung

Zur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses

Verfahrens ein Erdungsband am Handgelenk tragen. Bei Berührung der Rückwand mit der Hand oder

einem metallenen Werkzeug besteht Elektroschockgefahr.

Avvertenza

Durante questa procedura, indossare bracciali antistatici per evitare danni alla scheda causati da

un’eventuale scarica elettrostatica. Non toccare direttamente il pannello delle connessioni, né con

le mani né con un qualsiasi utensile metallico, perché esiste il pericolo di folgorazione.

Advarsel

Bruk jordingsarmbånd under prosedyren for å unngå ESD-skader på kortet. Unngå direkte berøring

av bakplanet med hånden eller metallverktøy, slik at di ikke får elektrisk støt.

Aviso

Durante este procedimento e para evitar danos ESD causados à placa, use fitas de ligação à terra

para os pulsos. Para evitar o risco de choque eléctrico, não toque directamente na parte posterior

com a mão ou com qualquer ferramenta metálica.

¡Advertencia!

Usartiras conectadas a tierra en las muñecas durante este procedimiento para evitar daños en la

tarjeta causados por descargas electrostáticas. No tocar el plano posterior con las manos ni con

ninguna herramienta metálica, ya que podría producir un choque eléctrico.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 119—Unit Short Circuit Protection

Varning!

Använd jordade armbandsremmar under denna procedur för att förhindra elektrostatisk skada på

kortet. Rör inte vid baksidan med handen eller metallverktyg då detta kan orsaka elektrisk stöt.

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure

that a fuse or circuit breaker no larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is used

on the phase conductors (all current-carrying conductors). The fuse or circuit breaker must have

adequate safety approval recognized by the country of usage.

Waarschuwing

Dit product is afhankelijk van de installatie van het gebouw voor bescherming tegen kortsluiting

(overstroom). Zorg ervoor dat de zekering of stroomonderbreker die gebruikt wordt niet groter is dan

120 V~, 20 ampère in de V.S. of 240 V~, 16-20 ampère internationaal op de fasegeleiders (alle

stroomdragende geleiders). De zekering of stroomonderbreker dient de juiste

veiligheidsgoedkeuringen te hebben in het land waarin het gebruikt wordt.

Varoitus

Tämä tuote on riippuvainen rakennuksen oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista,

että vaihejohtimissa (kaikissa jännitteellisissä johtimissa) käytetään alle 240 V vaihtovirran,

16–20 ampeerin (kansainvälinen) tai 120 V vaihtovirran, 20 ampeerin (Yhdysvallat) sulaketta tai

virtakytkintä. Sulakkeessa tai virtakytkimessä on oltava käyttömaassa tunnistetut, riittävät

turvahyväksynnät.

Attention

Pour la protection contre les courts-circuits (surtension), ce produit utilise les dispositifs intégrés

au bâtiment. Assurez-vous qu'un fusible ou un disjoncteur est utilisé sur les conducteurs de phase

(tous les conducteurs porteurs de courant). Le fusible ou le disjoncteur (maximum 240 V CA, 16 à 20 A

[aux USA, maximum 120 V CA, 20 A]) doit être conforme aux normes de sécurité en vigueur dans votre

pays.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 150—Power Off Before Working on System

Warnung

Diese Produkt erfordert eine Gebäudeabsicherung gegen Kurzschluß (Überstrom). Achten Sie

darauf, daß auf den Phasenleitern (allen stromführenden Leitern) eine Sicherung oder ein

Schaltkreisunterbrecher verwendet wird, der nicht größer ist als 120VAC, 20A U.S. (240VAC, 16 bis

20A international). Die Sicherung oder der Schaltkreisunterbrecher muß angemessenen

Sicherheitsvorschriften genügen, die den Bestimmungen des Anwendungslandes entsprechen.

Avvertenza

La protezione di questo prodotto da cortocircuiti (sovracorrente) dipende dall'impianto elettrico

dell’edificio. Assicuratevi che un fusibile o interruttore di circuito con meno di 120VAC, 20A U.S.

(240VAC, da 16 a 20A internazionale) venga utilizzato sui conduttori di fase (tutti i conduttori di

corrente elettrica). Il fusibile o interruttore di circuito deve rispondere alle specifiche di sicurezza

invigore nel paese dove viene utilizzato.

Advarsel

Dette produktet er avhengig av bygningens installasjoner for overstrømsbeskyttelse (kortslutning).

Kontroller at det ikke brukes en sikring eller overbelastningsbryter som er større enn 120 V,

20 ampere i USA, eller 240 V, 16 til 20 ampere internasjonalt, på faselederne (alle strømførende

ledere). Sikringen eller overbelastningsbryteren må være sikkerhetsgodkjent i det aktuelle landet

der den skal brukes.

Aviso

Este dispositivo depende das instalações existentes para protecção contra curto-circuitos

(sobrecarga). Assegure-se de que utiliza um fusível ou um disjuntor com uma capacidade não

superior a 120VAC, 20A U.S. (240VAC, 16 a 20A internacional) nos condutores de fase (todos os

condutores de corrente). O fusível ou disjuntor deverá possuir as necessárias aprovações de

segurança por parte das autoridades locais.

¡Advertencia!

Este producto ha sido diseñado teniendo en cuenta que la instalación del edificio contará con

protección contra cortocircuitos (sobrevoltajes). Asegúrese de que se usa un fusible o

cortacircuitos no superior a 120VAC, 20A en los EE.UU. (240VAC, de 16 a 20A en el resto de países)

en los conductores de fase (todos los conductores de transporte corriente). El fusible o

cortacircuitos debe contar con las aprobaciones de seguridad adecuadas y reconocidas por el país

en el que vayan a usarse.

Varning!

Denna produkt förlitar sig på att byggnadens installation är försedd med skydd mot kortslutning

(överström). Se till att en säkring eller ett överspänningsskydd för högst 120 V~, 20 A USA (240 V~,

16 – 20 A internationellt) används på fasledarna (alla strömförande ledare). Säkringen eller

överspänningsskyddet måste ha fullgoda säkerhetstillstånd som erkänns av användningslandet.

Warning

Before working on a system that has a standby/off switch, turn off the power by pressing the power

switch to standby and unplug the power cord.

Waarschuwing

Alvorens aan een systeem met een standby/uit-schakelaar te werken dient u de voeding uit te

schakelen door de voedingsschakelaar op standby te zetten en het voedingssnoer te verwijderen.

Varoitus

Katkaise virta valmiustila/virtakytkimellä varustetusta laitteesta ennen sen käyttämistä painamalla

virtakytkin valmiusasentoon ja irrottamalla sähköjohto.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 151—ISDN Network Voltages Warning

Attention

Avant d'utiliser un système équipé d'un commutateur « Standby/Off » (pause/arrêt), coupez

l'alimentation en plaçant le commutateur sur la position Standby et débranchez le cordon

d'alimentation.

Warnung

Bevor Sie an einem System mit einem Bereit-/Aus-Schalter arbeiten, stellen Sie den Strom ab, indem

Sie den Stromschalter auf "Bereit" stellen und das Stromkabel herausziehen.

Avvertenza

Prima di lavorare su un sistema con interruttore attesa/off, spegnetelo premendo il pulsante sulla

posizione di attesa e staccate la spina elettrica.

Advarsel

Før det utføres arbeid på et system som har en standby/av-bryter, skal strømmen slås av ved å skyve

av/på-bryteren til standby og trekke ut strømledningen.

Aviso

Antes de começar a trabalhar num sistema com um interruptor standby (posição de espera)/off

(desligado), desligue a corrente eléctrica colocando o interruptor na posição standby e retire o cabo

de alimentação da tomada.

¡Advertencia!

Antes de empezar a trabajar con un sistema cuyo interruptor incluya la posición standby, cierre la

corriente posicionando el interruptor a standby y a continuación desconecte el cable eléctrico.

Varning!

Innan du arbetar på ett system med en standby-/strömbrytaromkopplare, slå av strömmen genom att

ställa omkopplaren på standby och koppla ur nätsladden.

Warning

Network hazardous voltages are present in the ISDN cable. If you detach the ISDN cable, detach the

end away from the router first to avoid possible electric shock. Network hazardous voltages also are

present on the system card in the area of the ISDN port (RJ-45 connector), regardless of when power

is turned off (by pressing power switch to standby).

Waarschuwing

De ISDN-kabel bevat voltages die gevaar voor het netwerk opleveren. Als de ISDN-kabel verwijderd

moet worden, verwijdert u om mogelijke elektrische schokken te vermijden eerst het uiteinde dat

niet op de router is aangesloten. Verder bevat tevens de systeemkaart in de buurt van de ISDN-poort

(RJ-45-aansluiting) voltages die gevaar voor het netwerk opleveren, onafhankelijk van wanneer de

voeding wordt uitgeschakeld (door de voedingsschakelaar op standby te zetten).

Varoitus

ISDN-johdossa on verkolle vaarallisia jännitteitä. Jos ISDN-kaapeli irrotetaan, irrota ensin

reitittimen puoleinen pää sähköiskun välttämiseksi. Verkolle vaarallisia jännitteitä on myös

järjestelmäkortissa ISDN-portin alueella (RJ-45-liitin), vaikka virta olisikin katkaistu painamalla

virtakytkin valmiusasentoon.

Attention

Des tensions électriques réseau dangereuses circulent sur le câble RNIS. Pour éviter tout risque de

choc électrique lorsque vous débranchez ce câble, déconnectez d'abord l'extrémité non raccordée

au routeur. Par ailleurs, des tensions dangereuses sont également présentes autour du port RNIS

(connecteur RJ-45) de la carte système, que le système soit sous tension ou hors tension

(commutateur d'alimentation sur « Standby »).

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 162—EU Public Network Port Warning

Warnung

Auf dem ISDN-Kabel herrschen gefährliche Spannungen. Bei Entfernung des ISDN-Kabels muß

zuerst das Kabel von der Routerseite her abgetrennt werden, um einen möglichen elektrischen

Schlag zu vermeiden. Gefährliche Spannungen herrschen darüber hinaus auf der Systemkarte im

Bereich des ISDN-Ports (RJ-45 Steckverbinder) und zwar unabhängig davon, ob der Strom (durch

Umlegung des Stromschalters auf "Bereit") abgeschaltet ist.

Avvertenza

Sono presenti dei voltaggi elettrici rete pericolosi nei cavi ISDN. Se staccate il cavo ISDN, dovete

prima staccare l'estremità collegata al router per evitare scosse elettriche. Pericolose tensioni

elettriche rete sono presente anche sulla scheda del sistema vicino alla porta ISDN (connettore

RJ-45) a prescindere da quando sia stata spenta l'alimentazione elettrica (premendo il pulsante

sulla posizione di attesa).

Advarsel

Livsfarlig spenning er til stede i nettverkets ISDN-kabel. Hvis du kobler fra ISDN-kabelen, skal

enden som vender bort fra ruteren, kobles fra først for å unngå mulig elektrisk støt. Livsfarlig

spenning er også til stede på nettverkets systemkort i området ved ISDN-utgangen (RJ-45-kobingen),

uten hensyn til når strømmen er slått av (ved å skyve strømbryteren til standby).

Aviso

Existem tensões de rede perigosas no cabo de Rede Digital com Integração de Serviços-RDIS

(ISDN-Integrated Services Digital Network). Se for desligar o cabo RDIS, desligue primeiro a

extremidade oposta à do comutador para evitar possíveis choques eléctricos. Existem tensões de

rede perigosas também na placa do sistema, nomeadamente, na área da porta RDIS (conector RJ-45),

independentemente do facto da corrente estar desligada (ao colocar o interruptor em standby)

ou não.

¡Advertencia!

Las líneas RSDI contienen voltajes peligrosos de la red. Si desconecta el cable RSDI, separe

primero el final del router para evitar posibles choques eléctricos. La tarjeta del sistema en el área

del puerto RSDI (conector RJ-45) también contiene altos voltajes de la red, independientemente de

si está apagada (posicionando el interruptor de la corriente a standby).

Varning!

I ISDN-kabeln förekommer spänningar som är farliga för nätverk. Om du kopplar ur ISDN-kabeln,

undvik eventuell elstöt genom att först koppla ur den ände som är längst bort ifrån routern.

Spänningar som är farliga för nätverk förekommer också på systemkortet i området intill

ISDN-porten (RJ-45-koppling), oberoende av när strömmen slås av (genom att ställa omkopplaren på

standby).

Warning

If the symbol of suitability with an overlaid cross appears above a port, you must not connect the

port to a public network that follows the European Union standards. Connecting the port to this type

of public network can cause severe injury or damage your router.

Waarschuwing

Als er een geschiktheidsymbool met een overgetrokken kruis boven een poort aanwezig is, dan mag

u deze poort niet op een openbaar netwerk aansluiten dat aan de normen van de Europese Unie

voldoet. Als u de poort op een dergelijk openbaar netwerk aansluit, kan dit ernstig letsel of schade

aan uw router-eenheid veroorzaken.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 199—Emergency Access Warning

Varoitus

Jos portin päälle ilmestyy soveltuvuussymboli, jonka päällä on rasti, porttia ei saa liittää Euroopan

unionin standardien mukaiseen julkiseen verkkoon. Jos portti liitetään tällaiseen julkiseen

verkkoon, seurauksena voi olla henkilö- tai reititinvaurio.

Attention

Pour éviter tout risque d'accident corporel et/ou de dommage matériel, si le symbole de capacité

barré d'une croix apparaît au-dessus d'un port, il est vivement recommandé de ne pas connecter ce

port à un réseau public aux normes de l'Union Européenne.

Warnung

Wenn oberhalb des Ports das Verträglichkeitssymbol mit einem Kreuz darüber erscheint, dürfen Sie

den Port nicht an ein öffentliches Netzwerk anschließen, daß den Standards der Europäischen

Gemeinschaft folgt. Das Anschließen des Port an ein solches Netzwerk kann zu schweren

Verletzungen führen oder Ihren Router beschädigen.

Avvertenza

Se su una porta compare il simbolo di idoneità sbarrato, significa che la porta non può essere

collegata a una rete pubblica a norma UE. Collegando la porta a un simile tipo di rete pubblica si

possono correre seri rischi e provocare danni al proprio router.

Advarsel

Hvis symbolet for anvendelse med et kryss over vises over en utgang, skal utgangen ikke kobles til

et offentlig nettverk som følger EU-standardene. Hvis utgangen kobles til denne typen offentlig

nettverk, kan det medføre alvorlig personskade eller skade på ruteren.

Aviso

Se o símbolo de adequação com uma cruz sobreposta aparecer acima de uma porta, não conectar a

porta a uma rede pública que obedece aos padrões da União Europeia. A conexão da porta a este

tipo de rede pública pode causar avarias ou danos severos ao seu distribuidor.

¡Advertencia!

Si aparece el símbolo de idoneidad con una cruz sobrepuesta encima de un puerto, no debe conectar

el puerto a una red pública que siga los estándares de la Unión Europea. Si conecta el puerto a este

tipo de red pública puede lesionarse o dañar su router.

Varning!

Om lämplighetssymbolen med ett överlagt kors visas ovanför en port, får porten inte anslutas till ett

offentligt nätverk av EU-standard. Om porten ansluts till denna typ av offentligt nätverk kan det

förorsaka allvarlig personskada eller skada på routern.

Warning

This equipment is not designed for making emergency telephony calls when the power fails.

Alternative arrangements should be made for access to emergency services. Access to emergency

services can be affected by any call-barring function of this equipment.

Waarschuwing

Deze apparatuur is niet bedoeld voor noodtelefoongesprekken bij stroomstoringen. Voor

telefoondiensten in noodsituaties moet u andere maatregelen treffen. Eventuele

blokkeringsfuncties van deze apparatuur kunnen van invloed zijn op de bereikbaarheid van deze

telefoondiensten.

Varoitus

Tätä laitetta ei voi käyttää hätäpuheluihin, jos sähkövirta on katkennut. Käytettävissä täytyy olla

vaihtoehtoinen järjestelmä yhteyden saamiseksi hälytyskeskukseen. Hälytyskeskusyhteyden

estymiseen voi vaikuttaa mikä tahansa tämän laitteiston soitonestotoiminto.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 242—Equipment Grounding Warning

Attention

Cet équipement n’est pas conçu pour les télécommunications d’urgence en cas de panne

d’électricité et il importe de prévoir d'autres moyens d'accès aux services d'urgence. Cependant,

toute fonction d'interdiction d'appel de cet équipement risque d'avoir une incidence sur l'accès aux

services d'urgence.

Warnung

Dieses Gerät ist nicht geeignet für Notruftelefonate, wenn die Stromzufuhr ausfällt. Für das

Kontaktieren von Notfalldiensten sollten alternative Maßnahmen geplant werden. Das Kontaktieren

von Notfalldiensten kann von jeder der anrufsperrenden Funktionen dieses Gerätes beeinträchtigt

werden.

Avvertenza

Questo apparecchio non è predisposto per effettuare chiamate d’emergenza nel caso dimancanza di

alimentazione di corrente. È necessario pertanto predisporre misure alternative per consentire

l’accesso ai servizi di emergenza. Tale accesso può essere inoltre influenzato dalle funzioni di

blocco presenti sull’apparechio stesso.

Advarsel

Dette utstyret har ingen funksjon for nødtjenester når strømmen er brutt. En bør utarbeide alternative

ordninger hvis man må ha tilgang til nødtjenester. Tilgangen til nødtjenester kan bli påvirket av alle

samtalesperrende funksjoner i dette utstyret.

Aviso

Este equipamento não foi concebido para estabelecer chamadas telefónicas de emergência quando

faltar a energia. Devem tomar-se medidas alternativas para aceder a serviços de emergência. O

acesso aos serviços de emergência pode ser afectado por qualquer função de barramento de

chamadas aplicada a este equipamento.

¡Advertencia!

Este equipo no está diseñado para efectuar llamadas telefónicas de emergencia en caso de que falle

la alimentación. Se deberán tomar medidas alternativas para acceder a servicios de emergencia. El

acceso a servicios de emergencia puede verse afectado por cualquier función de bloqueo de

llamadas que pueda tener este equipo.

Varning!

Denna utrustning är inte utformad för telefonsamtal i nödläge när strömmen bryts. Andra

arrangemang måste göras för att kunna nå nödtjänster. Åtkomst till nödtjänster kan påverkas av alla

samtalsspärrningsfunktioner i denna utrustning.

Warning

This equipment needs to be grounded. Use a green and yellow 12 to 14 AWG ground wire to connect

the host to earth ground during normal use.

Waarschuwing

Deze apparatuur hoort geaard te worden. Gebruik een groen/gele 12 - 14 AWG aarddraad om de host

tijdens normaal gebruik met de aarde te verbinden.

Varoitus

Tämä laitteisto täytyy maadoittaa. Yhdistä isäntälaite maahan normaalikäytön aikana käyttämällä

vihreä-keltaista 12 - 14 AWG -maadoitusjohtoa.

Attention

Cet équipement doit être relié à la terre. Utilisez un fil vert et jaune de gabarit 12 à 14 (AWG) pour

connecter l'hôte à la terre lors de son utilisation normale.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 332—Antenna Installation Warning

This warning applies only to Cisco 850 series and Cisco 870 series routers.

Warnung

Dieses Gerät muß geerdet werden. Verwenden Sie ein grün/gelbes 12 bis 14-AWG-Erdungskabel, um

damit das Host-Gerät während des normalen Betriebs zu erden.

Avvertenza

Questa apparecchiatura deve essere collegata a massa. Durante l'uso normale, collegare l'host alla

massa di terra usando un filo di massa verde e giallo di diametro compreso tra 12 e 14 AWG.

Advarsel

Dette utstyret krever jording. Bruk grønn og gul 12-14 AWG jordingsledning til å kople

vertsterminalen til jording ved normal bruk.

Aviso

É necessário que este equipamento esteja ligado à terra. Utilize um fio de ligação à terra de 12 a 14

AWG, verde e amarelo, para ligar o host à ligação à terra durante a sua utilização normal.

¡Advertencia!

Este equipo debe conectarse a tierra. Utilizar un hilo de puesta a tierra entre 12 y 14 AWG verde y

amarillo para conectar a tierra el equipo principal durante el uso normal.

Varning!

Denna utrustning är avsedd att jordas. Använd en gulgrön jordledning av storlek 12 till 14 AWG till

att jorda värdenheten vid normal användning.

Warning

In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a

minimum of 7.9 inches (20 cm) or more from the body of all persons.

Waarschuwing

Om te voldoen aan de FCC radiofrequentie (RF) blootstellingslimieten dienen antennes zich minstens

20 cm of meer van de lichamen van alle personen bevinden.

Varoitus

FCC:n antamien radiotaajuuksille altistumista koskevien rajoitusten mukaan antennien on sijaittava

vähintään 20 cm:n päässä kaikista henkilöistä.

Attention

Pour se conformer aux limites d'exposition à la fréquence radio préconisées par la FCC (Federal

Communications Commission), les antennes doivent se situer à un minimum de 20 cm de toute

personne.

Warnung

Um die in den FCC-Richtlinien festgelegten Expositionshöchstgrenzen für Radiofrequenzen (RF)

nicht zu überschreiten, sollten Antennen mindestens 20 cm entfernt von Personen aufgestellt

werden.

Avvertenza

Per conformarsi ai limiti FCC di esposizione a radiofrequenza (RF), le antenne devono stare ad una

distanza minima di 20 cm dal corpo di ogni persona.

Advarsel

I henhold til eksponeringsgrensene for radiofrekvenser (RF), skal antenner befinne seg på en

avstand av minst 20 cm eller mer fra mennesker.

Aviso

Para estar de acordo com as normas FCC de limites de exposição para freqüência de rádio (RF), as

antenas devem estar distantes no mínimo 20 cm (7,9 pol) do corpo de qualquer pessoa.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 353—This Product Must be Connected

¡Advertencia!

Para cumplir con los límites de exposición de radio frecuencia (RF) de la Comisión Federal de

Comunicaciones (FCC) es preciso ubicar las antenas a un mínimo de 20 cm (7,9 pulgadas) o más del

cuerpo de las personas.

Varning!

För att följa FCC-exponeringsgränserna för radiofrekvens (RF), bör antenner placeras på minst 20 cm

avstånd från alla människor.

Warning

This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source

or an IEC60950 compliant limited power source.

Waarschuwing

Dit product moet worden verbonden met een stroomvoorziening die compatibel is met PoE

(power-over-ethernet) IEEE 802.3af of een beperkte stroomvoorziening die compatibel is met

IEC60950.

Varoitus

Tämä tuote on liitettävä PoE (power-over-ethernet) IEEE 802.3af -yhteensopivaan virtalähteeseen tai

IEC60950-yhteensopivaan rajoitettuun virtalähteeseen.

Attention

Ce produit doit être connecté à une source d'alimentation électrique par câble Ethernet (PoE)

conforme à la norme IEEE 802.3af ou à une source d'alimentation limitée conforme à la norme

IEC60950.

Warnung

Dieses Produkt muss entweder an eine Stromquelle angeschlossen sein, die mit dem IEEE

802.3af-Standard Power-over-Ethernet (PoE) kompatibel ist oder an eine Stromquelle für geringe

Leistungen, die IEC60950-kompatibel ist.

Avvertenza

Questo prodotto deve essere connesso a una fonte di alimentazione di tipo PoE

(power-over-ethernet) conforme a IEEE 802.3af o a una fonte di alimentazione conforme a IEC60950.

Advarsel

Dette produktet må være koblet til en Power-over-Ethernet (PoE) IEEE 802.3af-kompatibel strømkilde

eller en IEC60950-kompatibel begrenset strømkilde.

Aviso

Este produto tem de estar ligado a uma fonte de alimentação compatível com a norma IEEE 802.3af,

também conhecida pela sigla Power over Ethernet (PoE), ou a uma fonte de alimentação limitada

compatível com a norma IEC60950.

¡Advertencia!

Debe conectar este producto a una fuente de alimentación en Ethernet (PoE) conforme con el

estándar IEEE 802.3af, o a una fuente limitada conforme con el estándar IEC60950.

Varning!

Denna produkt måste vara ansluten till en PoE IEEE 802.3af-kompatibel strömkälla eller en

IEC60950-kompatibel begränsad strömkälla.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 371—Power Cable and AC Adapter

Statement 373—Must Connect To An Indoor Antenna

Warning

When installing the product, please use the provided or designated connection cables/power

cables/AC adaptors/batteries. Using any other cables/adaptors could cause a malfunction or a fire.

Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the

“UL” or “CSA” shown on the cord), not regulated with the subject law by showing “PSE” on the cord,

for any other electrical devices than products designated by CISCO.

Warning

This equipment must be connected to an indoor antenna only.

Waarschuwing

Deze apparatuur kan alleen worden aangesloten op een antenne voor binnengebruik.

Varoitus

Tämän laitteiston voi liittää vain sisäantenniin.

Attention

Cet équipement doit être connecté à une antenne intérieure uniquement.

Warnung

Diese Gerät darf nur an eine Innenantenne angeschlossen werden.

Avvertenza

Questo apparecchio può essere collegato solo a un'antenna da interno.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 378—Read Wall-Mounting Instructions Before Installation

Advarsel

Dette utstyret må kun kobles til en innendørsantenne.

Aviso

Este equipamento só pode ser ligado a uma antena interior.

¡Advertencia!

Este equipo sólo debe estar conectado a una antena de interior.

Varning!

Den här utrustningen får endast anslutas till en inomhusantenn.

Warning

Read the wall-mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people

and damage to the system.

Waarschuwing

Lees de wandbevestigingsinstructies aandachtig door voordat u met de installatie begint. Het niet

gebruiken van de juiste hardware of het opvolgen van de juiste procedures kan resulteren in een

gevaarlijke situatie voor mensen en schade aan het systeem.

Varoitus

Lue seinäkiinnitysohjeet huolellisesti läpi ennen työn aloitusta. Mikäli kiinnityksessä ei käytetä

oikeanlaisia työkaluja tai ohjeita ei noudateta tarkasti, järjestelmä saattaa aiheuttaa vaaratilanteen

tai se voi vaurioitua.

Attention

Lisez les instructions de montage murale avec attention avant de commencer l'installation. Ne pas

utiliser le matériel correct ou ne pas suivre les procédures correctes pourrait donner résultat a une

situation dangereuse pour les utilisateurs et endommager le système.

Warnung

Bitte lesen Sie vor Beginn der Installierung die Anleitungen zur Wandmontage sorgfältig durch.

Verwendung von inkorrekter Apparatur oder Nichtbefolgung der vorgeschriebenen Methoden kann

zur Gefährdung von Personen oder Schaden am System führen.

Avvertenza

Leggere attentamente le istruzioni per il montaggio al muro prima di iniziare l'installazione. Un

errato uso del corretto hardware o il mancato rispetto delle corrette procedure potrebbe avere come

conseguenza una situazione di pericolo per le persone e danni al sistema.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 393—Explosive Device Proximity Wireless Network Device

Advarsel

Les nøye gjennom instruksene om veggmontering før du begynner monteringen. Dersom man ikke

bruker riktig maskinvare eller ikke følger riktig framgangsmåte kan det resultere i risiko for

personskader og skade på systemet.

Aviso

Leia com cuidado as instruções de montagem na parede antes de iniciar a instalação. Falha em usar

o hardware correto ou em seguir os procedimentos corretos pode resultar numa situação de risco

para as pessoas e danos ao sistema.

¡Advertencia!

Lea atentamente las instrucciones que se encuentran en la pared antes de comenzar con la

instalación. Si no utiliza el hardware correcto o no sigue los procedimientos correctos se podría

producir una situación peligrosa para las personas y daños al sistema.

Varning!

Läs väggmonteringsintruktionerna noga innan du påbörjar installationen. Försummelse av att inte

använda rätt hårdvara eller att inte föjla korrekt tillvägagångsätt kan resultera i en riskabel

situation för människor och kan skada systemet.

Warning

Do not operate your wireless network device near unshielded blasting caps or in an explosive

environment unless the device has been modified to be especially qualified for such use.

Waarschuwing

Gebruik dit draadloos netwerkapparaat alleen in de buurt van onbeschermde ontstekers of in een

omgeving met explosieven indien het apparaat speciaal is aangepast om aan de eisen voor een

dergelijk gebruik te voldoen.

Varoitus

Älä käytä johdotonta verkkolaitetta suojaamattomien räjäytysnallien läheisyydessä tai

räjäytysalueella, jos laitetta ei ole erityisesti muunnettu sopivaksi sellaiseen käyttöön.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 1004—Installation Instructions

Attention

Ne jamais utiliser un équipement de réseau sans fil à proximité d'un détonateur non blindé ou dans

un lieu présentant des risques d'explosion, sauf si l'équipement a été modifié à cet effet.

Warnung

Benutzen Sie Ihr drahtloses Netzwerkgerät nicht in der Nähe ungeschützter Sprengkapseln oder

anderer explosiver Stoffe, es sei denn, Ihr Gerät wurde eigens für diesen Gebrauch modifiziert und

bestimmt.

Avvertenza

Non utilizzare la periferica di rete senza fili in prossimità di un detonatore non protetto o di esplosivi

a meno che la periferica non sia stata modificata a tale proposito.

Advarsel

Ikke bruk den trådløse nettverksenheten nært inntil uisolerte fenghetter eller i et eksplosivt miljø

med mindre enheten er modifisert slik at den tåler slik bruk.

Aviso

Não opere o dispositivo de rede sem fios perto de cápsulas explosivas não protegidas ou num

ambiente explosivo, a não ser que o dispositivo tenha sido modificado para se qualificar

especialmente para essa utilização.

¡Advertencia!

No utilizar un aparato de la red sin cable cerca de un detonador que no esté protegido ni tampoco

en un entorno explosivo a menos que el aparato haya sido modificado con ese fin.

Varning!

Använd inte den trådlösa nätverksenheten i närheten av oskyddade tändhattar eller i en explosiv

miljö om inte enheten modifierats för att kunna användas i sådana sammanhang.

Warning

Read the installation instructions before connecting the system to the power source.

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.

Varoitus

Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.

Avvertenza

Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.

Advarsel

Les installasjonsinstruksjonene før systemet kobles til strømkilden.

Aviso

Leia as instruções de instalação antes de ligar o sistema à fonte de energia.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.

Varning!

Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 1005—Circuit Breaker

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure

that the protective device is rated not greater than:

120 VAC, 15A U.S. (240 VAC, 10A international)

Waarschuwing

Dit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting

(overstroom). Controleer of de beschermingsinrichting niet meer dan:

120 VAC, 15A U.S. (240 VAC, 10A international) is.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Varoitus

Tämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta

(ylivirtasuojauksesta). Varmista, että suojalaitteen mitoitus ei ole yli:

120 VAC, 15A U.S. (240 VAC, 10A international)

Attention

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de

l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est

pas supérieur à :

120 VAC, 15A U.S. (240 VAC, 10A international)

Warnung

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz

installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als:

120 VAC, 15A U.S. (240 VAC, 10A international) beträgt.

Avvertenza

Questo prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro

cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating

superiore a:

120 VAC, 15A U.S. (240 VAC, 10A international)

Advarsel

Dette produktet er avhengig av bygningens installasjoner av kortslutnings (overstrøm)-beskyttelse.

Påse at verneenheten ikke er merket høyere enn:

120 VAC, 15A U.S. (240 VAC, 10A international)

Aviso

Este produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga).

Assegure-se de que o fusível ou disjuntor não seja superior a:

120 VAC, 15A U.S. (240 VAC, 10A international)

¡Advertencia!

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese

de que el dispositivo de protección no sea superior a:

120 VAC, 15A U.S. (240 VAC, 10A international)

Varning!

Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd).

Kontrollera att skyddsanordningen inte har högre märkvärde än:

120 VAC, 15A U.S. (240 VAC, 10A international)

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 1008—Class 1 Laser Product

Warning

Class 1 laser product.

Waarschuwing

Klasse-1 laser produkt.

Varoitus

Luokan 1 lasertuote.

Attention

Produit laser de classe 1.

Warnung

Laserprodukt der Klasse 1.

Avvertenza

Prodotto laser di Classe 1.

Advarsel

Laserprodukt av klasse 1.

Aviso

Produto laser de classe 1.

¡Advertencia!

Producto láser Clase I.

Varning!

Laserprodukt av klass 1.

Aviso

Produto a laser de classe 1.

Advarsel

Klasse 1 laserprodukt.

Regulatory Compliance and Safety Information for Cisco 800 Series Routers

OL-10260-06

Translated Safety Warnings

Statement 1010—Staring into Laser Beam

Warning

Do not stare into the laser beam.

Waarschuwing

Niet in de straal staren.

Varoitus

Älä katso säteeseen.

Attention

Ne pas fixer le faisceau des yeux.

Warnung

Nicht direkt in den Strahl blicken.

Avvertenza

Non fissare il raggio con gli occhi.

Advarsel

Stirr ikke på strålen.

Aviso

Não olhe fixamente para o raio.

¡Advertencia!

No mirar fijamente el haz.

Varning!

Laserstrålning när enheten är öppen.

GemTek Technology CISCO867VAE XDSL Router User Manual 800srcsi Gemtek

Gemtek Technology Co., Ltd. XDSL Router 800srcsi Gemtek

Contents

User Manual Statements Part 1

Navigation menu

Namespaces

Views

Navigation