Genex Telecom MK1995 GMRS Transceiver User Manual MK1995UserMan

Genex Telecom Co., Ltd. GMRS Transceiver MK1995UserMan

users manual

ROGERS LABS, INC. Genex Electronics4405 W. 259th Terrace MODEL: FRS 300Louisburg, KS  66053 Test #: 010419Phone/Fax: (913) 837-3214 Test to:  FCC Parts 2 and 95 Page 1 of 2FRS300Manual.doc 05/18/2001MK1995 Owners Operator ManualMK 1995Basic Operation_____ ___1. General Specification- Power On/Off Volume- PTT Key : Side [ Tact SW ]- Monitor Key : Side [ Tact SW ]- UP Key : Top- Down Key : Top- SCAN Key : Top- CALL Key : Top- Function Key : Top- EXT Mic/Charge Jack[ 2.5φ ]- EXT Speaker Jack[ 3.5φ ]2. Function Flow Chart → CTCSS → PWR Hi/Low → DW → VOX → BEEP → Roger Beep → Ringer Tone→ Vibration3. LCD Display
ROGERS LABS, INC. Genex Electronics4405 W. 259th Terrace MODEL: FRS 300Louisburg, KS  66053 Test #: 010419Phone/Fax: (913) 837-3214 Test to:  FCC Parts 2 and 95 Page 2 of 2FRS300Manual.doc 05/18/20014. Front, Side, Top Overview5. Operating Instruction1) On/Off & Volume control Switch- Radio ON : Rotate the switch clockwise until you here a 'click'. All indicators will appearmomentarily on the LCD and you will hear short beep sound.- Radio Off : Rotate the switch counter clockwise until all indicators disappear on the LCD.- Volume setting : Rotate On/Off Volume switch to mid position or adjust level that is mostcomfortable for you.2) Setting the ChannelMK 1995 has 15 main channels._ To select the channel- Turn the radio on- Press up[ ↑ ] or down[ ↓ ] button to choose the channel.
ROGERS LABS, INC. Genex Electronics4405 W. 259th Terrace MODEL: FRS 300Louisburg, KS  66053 Test #: 010419Phone/Fax: (913) 837-3214 Test to:  FCC Parts 2 and 95 Page 3 of 2FRS300Manual.doc 05/18/20013) Setting the Tone Code(CTCSS)MK 1995 has 38 CTCSS Codes_ To set the Tone Codes(CTCSS)- Press Function[F] button once more,[XX oF up to 38] will appear and tone code digit will blinkon the LCD. " oF " means no CTCSS code.- Press up[ ↑ ] or down[ ↓ ] button to choose the desired sub-channel to use.- Press the PTT button or Function[F] button to confirm.4) Setting the Transmit Power HI/LO- HI : 1.8W TX power- LO : 500mW TX power_ To set the TX output power- Press the Function [F] button until the [ Po LO or HI ] appears.- Press the up [ ↑ ] button or down [ ↓ ] button to set the TX power- Press the PTT button or Function [F] button to confirm.- HI or LO will appear on the LCD.- If the battery is in low condition, the TX Power will be switched to LO automatically. Even though theTX power is set to HI.5) Setting the DW(dual watch) and CTCSS in DW mode._ To active the DW mode- Press the Function [F] button until the [ oF or 1 up to 15] and DW icon blink on the LCD.- Press the up[ ↑ ] button or down [ ↓ ] button to choose the channel.- " oF " means no DW mode.- Press the PTT button or Function [F] button to confirm.- DW icon will appear on the LCD._ To stop the dual watch (DW)- Press the "S" Scan button, the unit will stop the dual watch and will return to normal operation and DWicon will disappear from the LCD.- DW icon will disappear from the LCD.6) VOX (Voice Operated Transmission)This option enables you to have hands-free conversation. You do not have to operate the PTT button eachtime when you want to transmit.You can also choose the VOX sensitivity to suit your environment of operation.(Ex ; noisy road, motor bike, factory etc.)_ To set the VOX mode.- Press the Function [F] button until the [ Uo oF or x ] appears. x  is a vox level- VOX icon will be appeared on the LCD._ To set the VOX level- Press the up[ ↑ ] button or down [ ↓ ] button to set the VOX level from 1 to 5."oF" is disable the VOX function." 3 " is most sensitive." 1 " is least sensitive.- Press the PTT button or Function [F] button to confirm.7) Beep tone_ To activate or disable the beep tone- Press the Function [F] button until [bP on or oF] and the BELL[ ] icon blink on the LCD.- Press the up[ ↑ ] button or down [ ↓ ] button.- Press the PTT button or Function [F] button to confirm.8) Roger toneThis feature will give the tone signal to other parties when transmitting finished (when PTT button isreleased.)
ROGERS LABS, INC. Genex Electronics4405 W. 259th Terrace MODEL: FRS 300Louisburg, KS  66053 Test #: 010419Phone/Fax: (913) 837-3214 Test to:  FCC Parts 2 and 95 Page 4 of 2FRS300Manual.doc 05/18/2001_ To activate or disable the Roger tone- Press the Function [F] button until [rb on or oF] and the Roger [ ] icon blink on the LCD.- Press the up[ ↑ ] button or down [ ↓ ] button.- Press the PTT button or Function [F] button to confirm.9) Setting the Ringer- This feature provides 3 user selectable call ringer signal and vibration.To set your favorite call ringer signal.- Press the Function [F] button until the [ CA 1 or up to 3 ] appears on the LCD.- Press the up[ ↑ ] button or down [ ↓ ] button to select the call melody type.- Press the PTT button to confirm.- To activate the call , click the "PTT" button twice quickly.10) Setting the Vibration Modes° To set for Vibration- Press the Function [F] button until the [ Ub on or oF ] and Vibrator[ ] icon blink on the LCD- Press the up [ ↑ ] button or down [ ↓ ] button.- Press the PTT button or Function [F] button to confirm.11) Transmitting- Press and hold the PTT button (The "TX" LED will light with red color)- Speak slowly and clearly- To stop the transmission, release the PTT button- If there are no more receiving signal for 5 seconds, the unit will go into power save mode and then the"TX" LED will blink with green color.12) ReceivingThe coding feature reduces the possibility of interference and provides enhanced communication.You can only listen to a call that has correct matching code.Important ;Before transmitting or receiving to the other parties ;- Correct channel is selected ( 1 to 15 ) andCorrect code is set ( 00 to 38 )13) Channel ScanningThis feature allows you to monitor all activated channels while scanning.% To activate the Scan- Press the Scan[S] button- Radio will begin scanning.- When in scan mode, the display will show each scanning channel.- After an activated channel is scanned and received signal and then if there is no more signal, the scanwill resume automatically.% To disable the Scan- Press the Scan[S] button, the unit will stop the scanning.- SCAN icon indicator will disappear from the LCD- The unit will return to home channel.14) Call- Press the Call[C] button.(The "TX" LED will light with red color.)15) Monitoring the channelIt is used for listening the week signal or to hear all activities on the channel by manually overridingchannel sub tone code setting.% To activate the Monitor feature- Press and hold the Monitor[M] button for over two seconds.- When you hear the sound, release the Monitor[M] button.(The monitor[ ] icon will appear on the LCD.)
ROGERS LABS, INC. Genex Electronics4405 W. 259th Terrace MODEL: FRS 300Louisburg, KS  66053 Test #: 010419Phone/Fax: (913) 837-3214 Test to:  FCC Parts 2 and 95 Page 5 of 2FRS300Manual.doc 05/18/2001To disable the Monitor feature- Press and hold the Monitor[M] button for over two seconds.(The monitor[ ] icon will disappear on the LCD.)16) BacklightBacklight is used to improve the display visibility in dark condition.% To activate the Backlight- Press and hold the Monitor[M] button in a moment.% To disable the BacklightPress and hold the Monitor[M] button in a moment once again.17) Keypad LockThe lock function is to avoid the accidental changes to channel with other radio settings. Allbuttons will be locked except the Power, PTT and monitor button.) To lock the keypad- Press and hold down the Scan[SC] button for over 2 seconds.- Keypad will lock.( LOCK[ ] icon will appear on the LCD)) To unlock the keypad- Press and hold down the Scan[SC] button for over 2 seconds.- Keypad will unlock. ( LOCK[ ] icon will disappear on the LCD)18) Battery status indicatorThe Battery[ ] icon will blink when the radio is in low battery power.Charge the rechargeable battery or replace the batteries.- Full battery - Battery[ ] icon is not displayed.- Low battery - Battery[ ] icon is displayed.- Low battery warning – Battery[ ] icon will blinking.19) External charger socketMIC socket can be used for the charging purpose.It should use the recommended rechargeable battery and wall charger.20) External Speaker - MicUse the approved accessories only to have the optimum performance.Ear/Mic unitFCC InformationTHIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS :(1) THIS DEVICE MAU NOT CAUSE HARMFUL INTERFERENCE, AND(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED OPERATION.Safety Information For GMRS UNITYour wireless handheld portable transceiver contains a low power transmitter. When the PTT button ispushed it sends out radio frequency (RF) signals. This device is authorized to operate at a duty factor notto exceed 50%. In August 1996, the Federal Communications Commission (FCC) adopted RF exposureguidelines with safety levels for hand-held wireless devices.Important: To maintain compliance with the FCC’s RF exposure guidelines, hold the transmitter atleast 1 inch (2.5 centimeters) from your face and speak in a normal voice, with the antenna pointed up andaway. If you wear the handset on your body while using the headset accessory, DO NOT TRANSMIT.The MK 1995supplied belt clip is for storage purposes ONLY. Use only the supplied antenna.Unauthorized antennas, modifications, or attachments could damage the transmitter and may violate FCCregulations.Normal Position: Hold the transmitter approximately 1” from your face and speak in a normal voice,with the antenna pointed up and away.

Navigation menu