Genie GPS1200 IC User Manual DC BELTDRIVE GDO Manuals And Guides L0703288

GENIE Garage Door Opener Manual L0703288 GENIE Garage Door Opener Owner's Manual, GENIE Garage Door Opener installation guides

User Manual: Genie GPS1200-IC GPS1200-IC GENIE GENIE DC BELTDRIVE GDO - Manuals and Guides View the owners manual for your GENIE GENIE DC BELTDRIVE GDO #GPS1200IC. Home:Garage Door & Opener Parts:Genie Parts:Genie GENIE DC BELTDRIVE GDO Manual

Open the PDF directly: View PDF .
Page Count: 32

Download
Open PDF In Browser	View PDF

Check
where
power
head ofyour
your ceiling
new unit
will the
be mounted.
Plan how you will be mounting the power head.
It is possible that ceiling joists may not be in the
exact position needed with respect to the garage
door operator. In any case, it may be necessary
to add an additional bracket and fasteners (not
included with your new door operator kit).

Check
the door
wall operator's
directly above
garage
door. The
headerthebracket
must be securely fastened to this wall. Insure
that the structure wilt provide a strong mounting
location.

clear

You
need aIf 110-120
power
available.
you plan Volt
to plug
the supply
unit into a
standard electrical outlet, is one available? The
outlet should be no more than about 3 feet from the
power head once it is mounted. (The cord is 4 ft. in
length.) SEE WARNING
BELOW.

To
avoid damage
to your
door and/or
operator,
make sure
you disable
any door
locks prior to installing your operator.

Check
see if the mounting
for
the to
Safe-T-Beam
® System location
(STB) is
from obstruction
and has a wood

surface available
for attaching
the STB
brackets.
The brackets may also be attached to
concrete if necessary but extra tools and special
fasteners (not supplied) will be required.
_,tOTE: Id2
S]*B
sS}_Hem
Ls Ms_a£edo
1.

Mounting brackets.
• Mark both sides of garage door frame or wall 5"
above floor (Fig. 3-1}.
• Hold bracket against door frame or wall.
- Check if brackets extend out from wall far
enough, so tongue of bracket is beyond door,
tracks or any door hardware.
- If not:
a. STB bracket extensions are available at
local dealer.
b. Blocks of wood, etc. may be substituted
for extensions.
• Center bracket on your mark (Fig. 3-2).
• Fasten each with 2 screws [127].

[127]

#10-16x
1-1/4,,

£0@' us£s£ co_crx;#(? _nchoMs (so£ pr'oyh;_!e@
2. Mounting STB source and sensor.
• If garage has only one garage door.
- Determine which side of garage receives
most direct sunlight (Fig. 3-4}.
- Red LED should always be on sunny side
whenever possible (Fig. 3-4).
• For multiple doors.
- Preventing crossed signals is critical.
- Place source and sensor modules on
adjacent doors facing in opposite directions
(Fig. 3-4).
£07%!i: Tb he@ p_we
h£',,_:vfT_p_nce/%gin
su S_{7
h,'om U

TWO DOOR
GARAGE

GARAGE

Uoo' ope,*ii;<£ wheh? fh<_,yvvHfsp<7;,/U/?oye

THREE DOOR
GARAGE

• Slide source/sensor onto tongue of bracket
until it clicks into place (Fig. 3-3).
Dashed
Solid

Line = striped
wire
Line = white wire
1

.

Wiring.
• Routewire using either method shown(Fig.
• Securely fasten wires to wall as you go.
- Use insulated staples (included).

[128]

I

3-5).
Source

Sensor

I
I
I
I

Insulated staple
_LPows

A
- Staples should be snug only.

I

r

L "sad

Source

I',I
i
I
i
i
i

Sensor

I
I
I
I
I
Power
Head

• Make wire attachments at STB's.
- Splitting and stripping wire ends to be
connected as shown (Fig. 3-6).
- Loosen terminal screws.
- Insert wire under flat plate and tighten screw. It
does not matter which wire, white or striped,
goes on which terminal (Fig. 3-7).
• Make wire attachments at power head.
- For ProMax. STB's are connected to terminals
#2 and #3 on power head (Fig. 3-8).
- For Stealth. STB's are connected to
terminals #3 and #4 on power head (Fig. 3-8).
4.

Check the following.
• Insure that no part of door or its hardware is in
path between lenses of source and sensor.
• Insure that tops of lenses are between 5"-6"
above the floor (Fig. 3-9). The brackets are
flexible and can be adjusted slightly if needed.

N07)_!::S _YI_
,dWm_.e_/ ohe_;k mu,_; be pey.¢Y_n_
ed
D_,Uio_vh_,_j
con/_ecff_:4_nto e/,_cf>:_,t_ it?owe_'{bee it?age 2)
_70 DiOT PLUO _"_,_+
YE I?

To correct the problem - the brackets are
flexible and can be adjusted slightly to bring
the system into alignment.
When the STB's are in alignment the red LED
will stop blinking and stay on.

SOURCE

(RED

LED

SENSOR

ON

(GREEN

LED

INDICATED

CONDITION

REQUIRED

ON

NORMALOPERATION

NONE REQUIRED

ACTION

O

OFF

O

OFF

1 sI_H%W "O

FOR(;E *

1. Adjust the "OPEN" Force (Fig. 7-1).
• Locate screw on back of power head marked
"OPEN FORCE."
• Gently turn screw counterclockwise until it stops.
t,JOT);!!!:_i_Y; c_o_" s _q_ i'md o u> _ _;_i"2_/:,_t;v'_:_u.
• Operate door using wall control.
• If door does not completely open, turn "OPEN
FORCE" screw clockwise slightly.
• Activate door using wall control.
• Repeat force adjustment until door will
completely open.

2.

• Close door, use wall control.
Adjust the "CLOSE FORCE" (Fig. 7-1}. Use wall
control to run door to the fully OPEN position
before starting "CLOSE FORCE" adjustment.
• Locate screw on back of power head marked
"CLOSE FORCE."
• Gently turn screw counterclockwise until it stops.

• Operate door using wall control.
• If door does not completely close, turn "CLOSE
FORCE" screw clockwise slightly.
• Operate door using wall control.
• Repeat force adjustment until door will
completely close.
HOT_;!!:Se he miAmun
k_u_;;e_quM_d o n _k<, _h_
d4";o_'
oh>se Sn aFlexthe nun bef thesr_ a//e_"the
l_)11:e

3.JCONTACT

REVERSE]

(Fig.
"/-2)

Fine adjustments for limit switches (see Section 8)
MUST BE completed before starting CONTACT
REVERSE.
• Open door, use wall control.
• Place a 2 by 4 board laid flat in center of doorway.
• Close door.
• Door MUST stop and reverse to open position. If it
does not, repeat fine adjustments for down limit
switch and "CLOSE FORCE" adjustment until the
door will reverse to the open position.
NO'L_f;!':
Se _'nLm m fouc_>
mquh'_d _'o _?M:®#oo_"ch:',_se
Ifdoor does notreverse,decrease"CLOSE FORCE"
until
door reverses.

STEALTH

During the following steps, the motor protector may
open. Wait about 20 minutes for protector to reset.
1.

Adjusting the "OPEN" limit switch (Fig. 8-1).
• Run door to open position by pushing wall control.
• Locate curved "OPEN" limit adjustment slot on
back of power head.
• Look into slot for pinion screw.
• Insert a screwdriver and turn pinion screw.
- clockwise to open more.
- counterclockwise to open less.

2.

Test door operator. Use wall control to run
door open and close.

3.

Repeat step as necessary to properly set
"OPEN" limit switch.

4.

Adjust the "CLOSE" limit switch (Fig. 8-1}.
• Run door fully closed by pushing wall control.
• Locate curved "CLOSE" limit adjustment slot on
back of power head.
• Look into slot for pinion screw.
• Insert a screwdriver and turn pinion screw.
- counterclockwise to close more.
- clockwise to close less.

5.

Test door operator.
open and close

6.

Repeat step as necessary to properly set
"CLOSE" limit switch

7.

Perform CONTACT REVERSE

II

Use wall control

to run door

OO AY'(;,

When Bs_)gP_f_mr_
F"W _::_;'_
oZx;_
cof_mF ke_V;;¢_tf_s
h'*c _es away t),de
4.

Erasing all receiver memory
• Press and hold learn code button on
power head
- 10 seconds or until light goes out
- Memory is erased
• Program door operator again
• Press remote control button once within
30 seconds
- LED on power head stays lit
• Press remote control button again
- LED on power head goes out and remote
control is programmed

Learn
code \
button

_

indicator

NOTE; f LEZ} b/_nks sp_o'ox mzs_,_#y
4 Si£_es pe_"
seco td, pmg_'_mr_ F_£ h,:_ss
e4 Ffpmgy_'_mkcg

1.

Turn remote control upside down (Fig. 10-1}

2.

Battery replacement (your remote control is
battery powered).
• Gently push straight IN on tab as shown
(Fig. 10-1).
- use ball point pen, coin or small screwdriver.
- battery cover snaps open.
• Install new battery in same position.
- use A23, @EVE_E,_D_,
12 Volt battery.

3.

Attach visor clip to remote control (Fig. 10-2)
• Slide visor clip into back of case until it snaps
into place.

4.

Remote control operation
• Point remote control at the garage door and
press the button. Door will move.
• Press remote control button again and door
will stop.
• Press remote control button again and the door
will move the other way. The door automatically
stops at the end of the open or close cycle.

Visor cNp
"_'7_

Battery
cover

Battery

1.

Install light bulb(s) into socket(s).
Do Not use short neck bulb(s).
Use bulb(s) rated for:
- rough service.
- vibration.
- appliances.
100 watt maximum.

2.

Bend two (2) slotted tabs up. This will activate
the "living hinge" of the lens (Fig. 11-1).

NOYY.!i:77u'?h;£>_iJ
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 32
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Wed Aug 15 16:13:31 2007
Author                          : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools