Genie TRI 800N Retail 9 01 09 5 Secs Rhine Remote Programming Instructions

User Manual: Genie 1024 - Product Support Information

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

7

PROGRAMMING REMOTE CONTROLS
WARNING

A moving door can cause serious injury or death.
1. Keep people clear of opening while door is
moving.
2. Do NOT allow children to play with opener,
including wall button, remote control, or
Wireless Keypad.
3. During programming, the door opener could
begin to run, so keep people and objects away
from the moving door and its parts. To keep the
door from moving, close the door and
disconnect it from the Opener by pulling the
Emergency Release.
NOTE: For remote control locate Box 3.
1a. Single Button Remote Programming.
NOTE: This opener can learn up to 7 transmitter
buttons.
‡ Locate “Learn Code” button and indicator
LED on the power head (Fig. 7-1).
‡ Press and release “Learn Code” button.
– Indicator LED will blink RED at a rate of twice
per second.
‡ Within 30 seconds, push remote control
button once.
– Indicator LED will stop blinking and stay ON.
‡ Press remote control button again.
– Red LED will go out. Remote is now
programmed and ready for use.
‡ Press remote control button again, door will move.
1b. Multi Button Remote Programming.
NOTE: Each button on a multi-button remote is
designed for use with 1 door. You cannot
program 2 buttons to operate the same door, nor
can you program 1 button to operate 2 doors.
You can program a maximum of 7 different
transmitters or wireless devices.
NOTE: Pushing two buttons on power head
simultaneously will erase programmed memory and
limits must be reset.
‡ For each button.
– Program each button separately using the
Single Button Remote Programming steps.
2. Operating.
‡ Press remote button once.
– Door will move.
‡ Press button again.
– Door will stop.
‡ Press button again.
– Door will move in opposite direction.
NOTE: The door will stop automatically at the
fully open or fully closed position.
LEARN

CODE

NOTE: To program a
Homelink® and Car2U®
device follow the Homelink® or Car2U®
instructions in your car owner’s manual.

FCC and IC CERTIFIED
This device complies with FCC Part 15 and RSS 210
of Industry Canada. This equipment has been tested
and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which may be determined by turning the
equipment OFF and ON, the user is encouraged to
try to correct the interference by one or more of the
following measures:
‡ Re-orient or relocate the receiver antenna.
‡ Increase the separation between the opener
and receiver.
‡ Connect the opener into an outlet on a circuit
different from that to which the receiver is
connected.
‡ Consult your local dealer.

Limit controls location
on power head.

LED
Indicator Light

Open
Travel Limit

To
Garage Door

Open
Set Limit
Button

OPEN

Up Force
Control
Adjustment

SET

LOST OR STOLEN REMOTE

LEARN MANUAL LIMIT FORCE

1. Clear memory.
‡ Press and hold learn code button (on power
head) for 10 seconds or until the red blinking
indicator LED goes out.
‡ Program remaining or new remote controls as
done previously. Your door opener will no
longer recognize any signal received from the
missing remote control, or any other which has
not been reprogrammed.

SET
Learn
Code
Button

FIG. 7-1

CODE

Close
Travel Limit

Close
Set Limit
Button

CLOSE

Down Force
Control
Adjustment

Learn code button and LED

PN# 37026500123, 02/26/2010 REV. 1

23

8

REMOTE CONTROL BATTERY REPLACEMENT AND VISOR CLIP INSTALLATION

1. Battery replacement.
• To open, gently push straight out on battery
cover lock tab as shown. (Fig. 8-1).
• Slide open battery cover.
– Remove old battery.
• Make sure new battery is facing proper direction
(Match battery polarity with symbols inside
battery housing) (Fig. 8-2).
– Recommended replacement battery type:
Alkaline A23, 12 volt.
NOTE: Batteries differ in care and maintenance.
Follow the manufacturer’s directions for battery
maintenance, replacement, and use.
• Slip new battery into place.
– Slide battery cover until it clicks shut.
• Operate remote to make sure it is working
properly. (No re-programming is needed.)
2. Visor clip.
(The visor clip may come already installed.)You
will have to install the visor clip if you choose to
attach your remote to the car visor.
• Slide visor clip into back of remote control.
– It will snap into place (Fig. 8-3).

Slide out

FIG. 8-1

Open battery cover.

– and + polarity marks
FIG. 8-2 Match battery polarity.

FIG. 8-3
Attach visor clip.

9

LIGHT BULB/ LENS INSTALLATION
Light bulb socket

WARNING
For added safety and protection please unplug
opener before installing light bulb.
NOTE: For lens covers locate Box 4.
1. Light bulb.
• Recommendations.
– Do NOT use a short neck bulb.
– Light bulbs should be no more than 60 Watts.
– Use a heavy duty service bulb for longer life.
• Screw 1 bulb into each socket.
2. Lens.
• Select a white (lamp) cover.
• On the power head end nearest the garage
door, line up lamp lens tabs on power head with
corresponding slots in lens (Fig. 9-1).
• Slide lens onto power head. Make sure the tabs
are fully engaged into lens slots (Fig. 9-2).
• Repeat for rear lens on power head.
• Plug power cord back into electrical outlet.
• Test lamp operation.

Lens tabs

Light bulb socket

FIG. 9-1

Slide each lens onto motor cover.

FIG. 9-2
Fasten lens.

24

PN# 37026500123

02/26/2010 REV. 1



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
PDF Version                     : 1.5
Page Count                      : 2
Author                          : bpaine
Create Date                     : 2011:12:20 14:32:42-05:00
Creator                         : PDFsam Basic v3.3.2
Modify Date                     : 2017:07:18 10:30:20-05:00
Producer                        : SAMBox 1.1.6 (www.sejda.org)
Title                           : Genie TRI 800N Retail 9-01-09 5 secs:3452535556 CG.qxd.qxd

EXIF Metadata provided by EXIF.tools