Gentex UAHL5C Universal Garage Door Opener Transmitter User Manual AV HL5 indd

Gentex Corporation Universal Garage Door Opener Transmitter AV HL5 indd

UserManual.wiki >

UAHL5C User Manual

Users Manual

The HomeLink® Wireless Control System provides a convenient way to replace up to three hand-held radio-frequency remotes used to activate devices such as gate operators, garage door openers, entry door locks, security systems, even home lighting. The below steps are generic programming instructions; for Genie and Sommer garage door openers please go directly to the HomeLink website. Additional information and programming videos can be found at www.HomeLink.com and www.youtube.com/HomeLinkGentex.Precautions!Before programming HomeLink to a garage door opener or gate operator, make sure that people and objects are out of the way of the device to prevent potential harm or damage. When programming a garage door opener, it is advised to park outside of the garage. Do not use HomeLink with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door that cannot detect an object signaling the door to stop and reverse does not meet current U.S. federal safety standards. It is also recommended that a new battery be placed in the hand-held remote (garage door opener remote) of the device for quicker and more accurate training. Some vehicles may require the ignition switch to be turned on or to the “accessories” position for programming and/or operation of HomeLink.Keep the hand-held remote (garage door opener remote) of the device you are programming for use in other vehicles as well as for future HomeLink programming. It is also suggested that upon the sale of the vehicle, the programmed HomeLink buttons be erased for security purposes. Refer to “Erasing HomeLink Buttons”. Programming a New HomeLink Button1. Press and release the HomeLink button that you would like to program.The HomeLink indicator light will ﬂ ash orange slowly (if not, refer to “Erasing HomeLink Buttons”).2. Position the hand-held remote (garage door opener remote) 1–3 inches(2–8 cm) away from the HomeLink button that you would like to program.Note: Some hand-held remotes (garage door opener remotes) may actually train better at a distance of 6-12 inches (15-20 cm). Keep this in mind if you have difﬁ culty with the programming process.3. While the HomeLink indicator light is ﬂ ashing orange, press and hold thehand-held remote button. Continue pressing the hand-held remote button until the HomeLink indicator light changes from orange to green. You may now release the hand-held remote button.Note: Some devices may require you to replace this “Programming a New HomeLink Button” step 3 with procedures noted in the “Gate Operator / Canadian Programming” section.

In the event that there are still programming difﬁ culties or questions, additional HomeLink information and programming videos can be found at www.HomeLink.com and www.youtube.com/HomeLinkGentex. For Genie and Sommer garage door openers please go directly to the HomeLink website.Gate Operator / Canadian Programming Canadian radio-frequency laws require transmitter remote signals to “time-out” (or quit) after several seconds of transmission, which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. The indicator LED on the hand-held remote will go off when the device times out, indicating that it has ﬁ nished transmitting.Programming a New HomeLink Button (cont’d.) 4. Press the HomeLink button that you would like to program and observethe indicator light. • If the indicator light remains constant green, your device shouldoperate when the HomeLink button is pressed. At this point, if your device operates, programming is complete. • If the indicator light rapidly ﬂ ashes green, ﬁ rmly press, hold fortwo seconds and release the HomeLink button up to three times to complete the programming process. At this point if your device operates, programming is complete. If the device does not operate, continue with the next step of the programming instructions.5. At the garage door opener motor, (security gate motor, etc...) locate the“Learn”, “Smart”, or “Program” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit (see the device’s manual to identify this button). The name and color of the button may vary by manufacturer. Note: A ladder and/or second person may simplify the following steps.6. Firmly press and release the “Learn”, “Smart”, or “Program” button. Younow have 30 seconds in which to complete step 7. 7. Return to the vehicle and ﬁ rmly press, hold for two seconds and releasethe HomeLink button up to three times. At this point programming is complete and your device should operate when the HomeLink button is pressed and released.8. If status indicator arrows appear next to the indicator light, please proceedto the “Garage Door Two-Way Communication” section.

Gate Operator / Canadian Programming (cont’d.)If you live in Canada or you are having difﬁ culties programming a gate operator or garage door opener by using the programming procedures, replace “Programming a New HomeLink Button” step 3 with the following:While the HomeLink indicator light is ﬂ ashing orange, press and release (“cycle”) your device’s hand-held remote every two seconds until the HomeLink indicator light changes from orange to green. You may now release the hand-held remote button.Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent possible overheating.Proceed with “Programming a New HomeLink Button” step 4 to complete.Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e. garage door opener, gate operator, security system, entry door lock, home/ofﬁ ce lighting, etc.). For convenience, the hand-held remote of the device may also be used at any time.Erasing HomeLink ButtonsTo erase programming from the three buttons (individual buttons cannot be erased but can be “reprogrammed” as outlined below), follow the step noted:Press and hold the two outer HomeLink buttons for at least 10 seconds. The LED indicator will change from continuously lit to rapidly ﬂ ashing. Release both buttons. Do not hold for longer than 20 seconds. HomeLink is now ready to be programmed at any time beginning with “Programming a New HomeLink Button” - step 1.Reprogramming a Single HomeLink ButtonTo program a previously trained button, follow these steps:1. Press and hold the desired HomeLink button. DO NOT release the button.2. The indicator light will begin to slowly ﬂ ash orange after 20 seconds. The HomeLink button can bereleased at this point. Proceed with “Programming a New HomeLink Button” - step 3.3. If you do not complete the programming of a new device to the button, it will revert to the previouslystored programming.