Getac Technology 012 Notebook with WLAN User Manual M220 0A

Getac Technology Corp. Notebook with WLAN M220 0A

Manual

Download:
Mirror Download [FCC.gov]
Document ID	510318
Application ID	ioTv93Qo3CRdry/FHgs4TQ==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	171.09kB (2138643 bits)
Date Submitted	2005-01-27 00:00:00
Date Available	2005-01-27 00:00:00
Creation Date	2005-01-26 10:46:41
Producing Software	Acrobat PDFWriter 4.0 for Windows NT
Document Lastmod	2005-01-26 11:12:44
Document Title	M220-0A.PDF
Document Creator	M220-0A - Microsoft Word
Document Author:	8112009

M220
Operation Manual
MITAC Technology Corporation
Part Number: 0000 0000 0001 R00
(December 2004)
TRADEMARKS
All brand and product names are trademarks or registered trademarks of their
respective companies.
NOTE
The information in this manual is subject to change without notice.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded interface
cables when connecting to computer or peripheral devices) any changes or modifications
not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Table of Contents
Preface................................................................................................viii
Chapter 1 Getting Started .............................................................1-1
Getting the Computer Running .............................................1-2
Unpacking.....................................................................1-2
Connecting to AC Power ...............................................1-2
Opening the Cover.........................................................1-4
Turning On and Off the Computer ..................................1-4
Taking a Look at the Computer............................................1-6
Right-Side Components ..................................................1-6
Left-Side Components....................................................1-7
Rear Components ..........................................................1-8
Front Components........................................................1-10
Bottom-Side Components .............................................1-12
Top-open Components .................................................1-13
Where to Go from Here ....................................................1-15
Chapter 2 Operating Your Computer.........................................2-1
Starting and Stopping the Computer......................................2-2
Starting the Computer ....................................................2-2
Stopping the Computer ...................................................2-2
Using the Keyboard ............................................................2-4
Typewriter Keys............................................................2-4
Cursor-Control Keys ......................................................2-5
Numeric Keypad ...........................................................2-5
Euro Symbol..................................................................2-6
Windows Keys..............................................................2-6
Function Keys ...............................................................2-6
Fn Key .........................................................................2-7
Hot Keys ......................................................................2-7
Using the Touchpad............................................................2-9
Configuring the Touchpad ............................................ 2-11
Using the Touchscreen (option) ......................................... 2-12
Using the Hard Disk Drive ................................................ 2-13
Using the Optical Drive ..................................................... 2-14
Installing the CD/Combo/DVD RW Drive..................... 2-15
Inserting and Removing a Disc ..................................... 2-16
Using the Video Features .................................................. 2-17
Configuring the Display Modes..................................... 2-17
Using the Audio Features .................................................. 2-19
Connecting Audio Devices ........................................... 2-20
Using the Communication Features .................................... 2-21
Using the LAN............................................................ 2-21
Using the Wireless LAN (WLAN) ............................... 2-21
Using the Modem........................................................ 2-23
Chapter 3 Managing Power .........................................................3-1
AC Adapter .......................................................................3-2
Battery Pack......................................................................3-3
Charging the Battery Pack.............................................3-3
Initializing the Battery Pack............................................3-4
Checking the Battery Level............................................3-4
Using the Primary Battery Pack.....................................3-5
Using the Secondary Battery Pack .................................3-6
Battery Low Signals and Actions ....................................3-7
Power Management............................................................3-8
Hibernation ...................................................................3-9
ii
Power-Saving Tips............................................................3-10
Chapter 4 Expanding Your Computer.......................................4-1
Connecting an External Monitor ...........................................4-2
Connecting a USB Device...................................................4-4
Connecting the PS/2 Keyboard and Mouse ...........................4-5
Connecting a Parallel Device ...............................................4-6
Connecting a Serial Device..................................................4-7
Connecting an IR Device.....................................................4-8
Using PC Cards ................................................................4-10
PC Card Type .............................................................4-10
CardBus Support .........................................................4-10
Inserting and Removing a PC Card...............................4-10
System Memory Upgrade ..................................................4-12
Chapter 5 Setup Configuration Utility (SCU)...........................5-1
When and How to Use the SCU Program ............................5-2
When to Use .................................................................5-2
Starting SCU .................................................................5-2
Moving Around and Making Selections............................5-4
Main Menu.........................................................................5-5
Advanced Menu .................................................................5-7
HDD Heater ...............................................................5-11
Security Menu ..................................................................5-12
Boot Menu .......................................................................5-15
Exit Menu.........................................................................5-17
Chapter 6 Installing Software Drivers........................................6-1
How to Use the Driver CD..................................................6-2
Installing Drivers for Windows 2000.....................................6-3
Touchscreen Driver .......................................................6-6
Installing Drivers for Windows XP .......................................6-7
Touchscreen Driver .....................................................6-10
Touchscreen Utility......................................................6-16
iii
Chapter 7 Caring for the Computer ...........................................7-1
Protecting the Computer......................................................7-2
Using the Password.......................................................7-2
Using the Cable Lock ....................................................7-2
Using an Anti-Virus Strategy..........................................7-3
Taking Care of the Computer ..............................................7-4
Location Guidelines........................................................7-4
General Guidelines.........................................................7-4
Cleaning Guidelines........................................................7-5
Battery Pack Guidelines.................................................7-5
When Traveling ..................................................................7-6
Chapter 8 Troubleshooting..........................................................8-1
Preliminary Checklist ..........................................................8-2
Solving Common Problems ..................................................8-3
Battery Problems...........................................................8-4
Optical Drive Problems ..................................................8-4
Display Problems...........................................................8-5
Hardware Device Problems ...........................................8-7
Hard Disk Drive Problems .............................................8-7
Infrared Problems..........................................................8-7
Keyboard, Mouse and Touchpad Problems......................8-8
LAN Problems ..............................................................8-9
WLAN Problems ..........................................................8-9
Modem Problems ........................................................ 8-10
PC Card Problems....................................................... 8-11
Power Management Problems...................................... 8-11
Printer Problems.......................................................... 8-12
Software Problems ...................................................... 8-12
Sound Problems........................................................... 8-13
Startup Problems ......................................................... 8-13
Other Problems ........................................................... 8-14
Resetting the Computer..................................................... 8-16
iv
Appendix A Specifications ..........................................................A-1
Appendix B Regulatory Information .........................................B-1
On the Use of the System...................................................B-2
Class B Regulations ......................................................B-2
Safety Notices..............................................................B-3
On the Use of RF Device...................................................B-6
USA and Canada Safety Requirements and Notices .......B-6
European Union CE Marking and Compliance Notices ....B-9
Preface
This manual contains information that will help you operate the computer.
It is divided into 8 chapters and 2 appendices.
??
Chapter 1, Getting Started, takes you through the process of setting
up the computer and identifying its external components.
??
Chapter 2, Operating Your Computer, tells you how to use the
computer’s components and features.
??
Chapter 3, Managing Power, provides information on power.
??
Chapter 4, Expanding Your Computer, provides information on
installing and using peripheral devices.
??
Chapter 5, Using BIOS Setup, describes the SCU program that
configures the computer’s BIOS settings.
??
Chapter 6, Installing Software Drivers , describes how to install the
drivers and utilities supplied with the computer.
??
Chapter 7, Caring for the Computer, gives you tips in care and
maintenance.
??
Chapter 8, Troubleshooting, gives solutions to common problems
you may encounter when using the computer.
??
Appendix A, Specifications , gives a brief specification of the
computer.
??
Appendix B, Regulatory Information, provides regulatory
statements and safety notices on your computer.
vii
Notational Conventions
Throughout this manual, the following conventions are used to distinguish
elements of text.
NOTE: identifies additional information that requires special attention.
CAUTION: identifies important information that, if not followed, may result in loss of data or
damage to the computer.
Keyboard keys are shown in a bold typeset. For example:
Press Enter to complete.
When keys are joined by a plus sign (+), press the first key, and, while
keeping the first key down, press the remaining keys, finally release all the
keys. When necessary, keys are also shown in graphics.
A title, command, setup item, or button that you can see on the screen is
shown in boldface. A value or an option that you can select for a setup
item is shown in italic. For example:
Select Power Schemes, set it to Portable/Laptop, and then click
the OK button.
viii
CHAPTER
Getting Started
Congratulations on purchasing this computer.
This high performance notebook computer is especially designed for the
practical applications of warehouses, automobiles, vehicles, public
security, repairing, assisting the handicapped, and other demanding
situations where conventional notebook computers just cannot measure
up.
This chapter first tells you step by step how to get the computer up and
running. You will find instructions for these procedures:
??
Unpacking
??
Connecting to AC power
??
Opening the cover
??
Turning on the computer
??
Turning off the computer
Then, you will find a section briefly introducing the external components
of the computer. And the last section navigates you to the information
you may need after the computer is ready for use.
Getting the Computer Running
This section guides you through the procedures for getting the computer
ready for operation.
Unpacking
After unpacking the shipping carton, you should find these standard
items:
??
Notebook computer
??
Accessories:
? AC adapter (100~240 VAC, 50/60 Hz)
? AC power cord (US/CE/UK/SA)
? Car adapter (option)
? Extra battery pack (option)
? Touchscreen pen (option)
? Driver CD
? This Operation Manual
? Vehicle docking (option)
? Office docking (option)
? Carrying bag (option)
Inspect all the items. If any item is damaged or missing, notify your
dealer immediately.
Keep the shipping carton and packing materials in case you need to ship
or store the computer in the future.
Connecting to AC Power
The computer operates either on the external AC power or internal
battery power. It is suggested that you use AC power when you start up
the computer for the first time.
CAUTION: Use only the AC adapter included with your computer. Using other AC
adapters may damage the computer.
1-2
Getting Started
NOTE:
Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated
minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates
with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P)
configuration; other end terminates with a molded-on appliance coupler.
Alternative: (optional) Detachable, maximum 4.5 m (14.76 ft) long. Listed, rated
minimum 250 V, 6 A, having a 3/18 AWG, type SVT flexible cord. One end terminates
with a Tandem blade, grounding, listed molded-on, attachments plug with a 6 A, 250 V
(NEMA 6-15P) configuration; other end terminates with a molded-on appliance
coupler.
1. Make sure the computer is turned off.
2. Plug the DC cord of the AC adapter to the power connector on the
rear side of the computer (?) .
3. Plug the female end of the AC power cord to the AC adapter and the
male end to an electrical outlet (?) .
AC in
4. When the AC adapter is connected, the indicator on the AC adapter
lights up, indicating that power is being supplied from the electrical
outlet to the AC adapter and onto your computer. Now, you are ready
to turn on the computer.
Getting Started
1-3
CAUTION:
?? When you disconnect the AC adapter, disconnect from the electrical outlet first and
then from the computer. A reverse procedure may damage the AC adapter or the
computer.
?? When unplugging the connector, always hold the plug head. Never pull on the cord.
NOTE: When the AC adapter is connected, it also charges the battery pack. For
information on using battery power, see Chapter 3.
Opening the Cover
CAUTION: Be gentle when opening and closing the cover. Opening it vigorously or
slamming it shut could damage the computer.
1. Open the top cover by pushing on the top portion of the cover latch,
and then pulling on the bottom portion of the cover latch.
Cover latch
2. Lift up the cover. You can tilt the cover forward or backward for
optimal viewing clarity.
Turning On and Off the Computer
Turning On
1. Make sure the computer is connected to AC power.
1-4
Getting Started
2. Press the power button.
Power
button
3. Each time the computer is turned on, it performs a Power-On Self
Test (POST), and the operating system such as Windows should
start.
Turning Off
To turn off the computer power, use the “Shut Down” command of your
operating system.
NOTE: There are other ways you can stop the computer so that you will be back to
where you left off when you next turn on the computer. (See “Stopping the Computer”
in Chapter 2 for information.)
CAUTION: If you have to turn the computer on again immediately after turning it off,
wait for at least five seconds. Turning the computer off and on rapidly can damage it.
Getting Started
1-5
Taking a Look at the Computer
This section identifies the external components of the computer and
briefly describes the function of each component.
NOTE: Depending on the model you purchased, the appearance of your computer may
not exactly be the same as those shown in this manual.
Right-Side Components
Ref
Component
??
Description
See Also
Primary
Battery Pack
Supplies power to your computer when external
power is not connected.
PC Card Slot
Accepts a PC card for additional functions.
USB Ports
Each of the two ports connects a USB device,
such as a USB floppy drive, printer, digital
camera, joystick, and more.
P. 4-4
PS/2 Port
Connects a PS/2 keyboard and/or mouse.
P. 4-5
1-6
P. 3-5
P. 4-10
Getting Started
Left-Side Components
Ref
Component
CD/ Combo/
DVD RW Drive
Accepts a compact disc (CD) for installing or
loading software, accessing data, and playing
music/video.
Secondary
Battery Pack
You can purchase a secondary battery pack that
supplies power to your computer when external
power is not connected.
Hard Disk
Drive Slot
Inside is the hard disk drive of your computer.
Getting Started
Description
See Also
P. 2-14
P. 3-6
P. 2-13
1-7
Rear Components
? ? ? ?? ?
Ref
Component
? ??
Description
See Also
IR Port
Connects an IrDA-compliant device for wireless
data transfer.
P. 4-8
Power
Connector
Connects the AC adapter.
P. 1-3
Serial Port
Connects a serial device, such as an external
modem.
P. 4-7
RJ-11
Connector
Connects the telephone line.
P. 2-24
RJ-45
Connector
Connects the LAN cable.
P. 2-22
VGA Port
Connects an external monitor.
P. 4-2
Parallel Port
Connects a parallel device, such as a printer.
P. 4-6
Microphone
Connector
Connects an external microphone.
1-8
P. 2-21
Getting Started
Ref
Component
Audio Output
Connector
Getting Started
Description
Connects a set of headphones, external speakers
with amplifier, an audio recording device, or an
S/PDIF device such as a digital speaker set for
digital audio output.
See Also
P. 2-21
1-9
Front Components
Ref
1-10
Component
Top Cover
Latch
Description
Locks the top cover.
See Also
P. 1-4
Getting Started
Ref
Component
Device
Indicators
Description
See Also
Show the current status of the computer’s
devices.
AC power indicator.
P. 3-2
Glows green when the computer is using AC
power.
Blinks green when the computer, using AC
power, is in Standby mode.
Battery Charge Indicator
P. 3-3
Glows green when the battery is fully charged
and connected to AC power.
Glows amber when the battery is being charged.
Blinks red when the battery is almost completely
discharged.
Battery Power Indicator
P. 3-7
Glows green when the computer is using battery
power.
Blinks green when the computer, using battery
power, is in Standby mode.
CD/Combo/DVD RW drive in-use indicator
P. 2-14
Wireless LAN (Local Area Network) indicator
P. 2-22
Wired LAN indicator
P. 2-22
P. 2-12
Touchscreen
Pen (option)
Provides a convenient way to use the
touchscreen. Can be stretched for better grip and
handling.
Handle
Allows you to carry your computer for an easy
grip.
Kensington
Lock
Locks the computer to a stationary object for
security.
Getting Started
P. 7-2
1-11
Bottom-Side Components
Ref
Component
Description
See Also
Reserved
Opening
Opening reserves for upgrade model
------
Release Knob
Allows you to remove the CD/ Combo/DVD RW
drive as well as eject the secondary battery pack.
P. 2-14
P. 3-6
Docking
Connector
(POGO)
For connecting to a Port Replicator / car mount
(both are available as an option).
Memory Slot
Contains the memory slot for expanding the
memory size of your computer.
P. 4-12
Stereo Speaker
Set
Sends out sound and voice from the computer.
P. 2-20
1-12
Getting Started
Top-open Components
Ref
Component
Description
Power Button
Turns the computer power ON and OFF.
LCD Screen
Displays the output of the computer.
Getting Started
See Also
P. 1-5
P. 2-18
1-13
Ref
Component
Device
Indicators
Description
See Also
Show the current status of the computer’s
devices.
Power On Indicator
Glows green when the computer is on.
Blinks green when the computer is in Standby
mode.
Hard Disk Drive Indicator
P. 2-13
Blinks green when the hard disk drive is active.
Blinks red when the hard disk heater is on.
Scroll Lock indicator
P. 2-4
Num Lock indicator
P. 2-4
Caps Lock indicator
P. 2-4
Keyboard
Serves as the data input device of the computer.
P. 2-4
Touchpad
Serves as the pointing device of the computer.
P. 2-9
1-14
Getting Started
Where to Go from Here
As your computer is ready for operation, you may want to do any of the
following now:
For this purpose…
Do this…
To know more about the computer…
Go on to the next chapter.
To install the operating system if your
dealer has not already done so…
See the operating system manual.
To know more about the operating
system…
Read the operating system manual.
To install the drivers if your dealer has See Chapter 6.
not already done so…
To set a power-on password…
See “Security Menu” in Chapter 5.
To charge the battery pack for the first See “Charging the Battery Pack” in
time…
Chapter 3.
Getting Started
1-15
CHAPTER
Operating Your Computer
This chapter provides information about the use of the computer.
If you are new to computers, reading this chapter will help you learn the
operating basics. If you are already a computer user but are new to
notebook computers, you may choose to read only the parts containing
information unique to your computer.
Described in this chapter are the operating basics of these components:
??
Keyboard
??
Touchpad
??
Touchscreen
??
Floppy disk drive
??
Hard disk drive
??
Optical drive
And these features:
??
Starting and stopping the computer
??
Video features
??
Audio features
??
Communication features
Starting and Stopping the Computer
There are a number of ways to start and stop the computer.
Starting the Computer
You always start the computer using the power button.
A computer starts up with an operating system (OS) existing on the
storage device such as the hard disk; or from a floppy disk or CD if you
have the respective modules installed. The computer will automatically
load the OS after you turn it on. This process is called booting.
NOTE: An operating system is the platform for all your software application programs to
run on. The most widely used operating system today is Microsoft Windows.
Stopping the Computer
When you finish a working session, you can stop the computer by turning
off the power or leaving the computer in Standby or Hibernation mode:
To stop in
this mode…
Off
Do this…
To start up or
resume again
Follow the shutdown procedure of your
operating system. This can prevent loss of
unsaved data or damage to your software
programs.
Press the power
button.
If the system is locked up because of
hardware or software problems, press the
power button to turn off the computer.
Standby
2-2
Depending on your settings in Windows,
you can place the computer in Standby
mode by:
?? Closing the display cover
?? Pressing the power button
Press any key.
Operating Your Computer
To stop in
this mode…
Do this…
To start up or
resume again
Hibernation
Depending on your settings in Windows,
you can place the computer in
Hibernation mode by:
?? Closing the display cover.
?? Pressing the power button
Press the power
button.
If you choose to stop in Standby or Hibernation mode, you can return to
where you left off the next time you start up the computer. (See “Power
Management” in Chapter 3 for more information.)
Operating Your Computer
2-3
Using the Keyboard
Your keyboard has all the standard functions of a full-sized computer
keyboard plus a Fn key added for specific functions.
The standard functions of the keyboard can be further divided into four
major categories:
??
Typewriter keys
??
Cursor-control keys
??
Numeric keys
??
Function keys
Typewriter Keys
Typewriter keys are similar to the keys on a typewriter. Several keys are
added such as the Ctrl, Alt, Esc , and lock keys for special purposes. When
the lock keys (Caps Lock, Num Lk, and Scroll Lk) are pressed, their
corresponding indicators light up.
The Control/Alternate key is normally used in combination with other
keys for program-specific functions. The Escape key is usually used for
stopping a process. Examples are exiting a program and canceling a
command. The function depends on the program you are using.
2-4
Operating Your Computer
Cursor-Control Keys
NOTE: The word “cursor” refers to the indicator on the screen that lets you know
exactly where on your screen anything you type will appear. It can take the form of a
vertical or horizontal line, a block, or one of many other shapes.
Numeric Keypad
A 15-key numeric keypad is embedded in the typewriter keys as shown
next:
Operating Your Computer
2-5
Numeric keys facilitate entering of numbers and calculations. When Num
Lock is on, the numeric keys are activated; meaning you can use these
keys to enter numerals.
NOTES:
?? When the numeric keypad is activated and you need to type the English letter in the
keypad area, you can turn Num Lock off or you can press Fn and then the letter
without turning Num Lock off.
?? Some software may not be able to use the numeric keypad on the computer. If so,
use the numeric keypad on an external keyboard instead.
Euro Symbol
You can press the Euro dollar sign
on the keyboard.
??
To press the Euro sign on the keyboard, hold down either of the Alt
keys and type 0128 on the numeric keypad of your keyboard.
??
To press the Euro sign on an UK keyboard, hold down the Alt Gr key
and press 4 (which has an Euro sign on it).
Windows Keys
The keyboard has two keys that perform Windows-specific functions:
Windows Logo key and
Application key.
The
Windows Logo key opens the Start menu and performs
software-specific functions when used in combination with other keys.
The
Application key usually has the same effect as a right mouse
click. (See your Windows manual for more information.)
Function Keys
On the top row of the keys are the function keys: F1 to F12. Function keys
are multi-purpose keys that perform functions defined by individual
programs.
2-6
Operating Your Computer
Fn Key
The Fn key, at the lower left corner of the keyboard, is used with another
key to perform the alternative function of a key. The letter “Fn” and the
alternative functions are identified by the color of blue on the keytop. To
perform a desired function, first press and hold Fn , then press the other
key.
Hot Keys
Hot keys refer to a combination of keys that can be pressed any time to
activate special functions of the computer. Most hot keys operate in a
cyclic way. Each time a hot key combination is pressed, it shifts the
corresponding function to the other or next choice.
You can easily identify the hot keys with the icons imprinted on the
keytop. The hot keys are described next.
Key
Description
Switches the optional keyboard backlight function on/off with
10 levels of brightness in-between.
Decreases the sound volume.
Increases the sound volume.
Decreases the LCD brightness.
Increases the LCD brightness.
Switches the LCD backlight on and off
Switches LCD on and off.
Operating Your Computer
2-7
Key
Description
Switches the display output to one of the following when an
external device is connected.
Upon booting the system with CRT:
LCD
CRT
LCD & CRT
NOTES:
??
Fn+F9 will not work when playing a DVD/MPEG movie.
??
Using the VGA utility’s “Graphics Properties” to switch the
display output is not allowed.
??
Display switching when in full screen (maximize view)
DOS mode is not allowed.
??
If the display mode is set to 256 colors or lower, or in DOS
mode, there will be only two modes for selecting: CRT only
and LCD & CRT.
??
This function only applies to Plug & Play CRT monitors.
Serves as the sleep button that you can define with Windows’
Power Management. (See the “Power Management” in
Chapter 3.)
Switches the wireless LAN radio on and off.
NOTE: The FAA (Federal Aviation Agency) has deemed it
unsafe to operate wireless devices in aircraft as this may
interfere with flight safety. Remember to turn off wireless LAN
when using your computer in the airplane.
Switches the optional GPS function on and off.
2-8
Operating Your Computer
Using the Touchpad
CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may
damage the touchpad surface.
NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean
and dry. When tapping on the pad, tap lightly. Do not use excessive force.
The touchpad is a pointing device that allows you to communicate with
the computer by controlling the location of the pointer on the screen and
making selection with the buttons.
Touchpad
The touchpad consists of a rectangular pad and two buttons. To use the
touchpad, place your forefinger or thumb on the pad. The rectangular pad
acts like a miniature duplicate of your display. As you slide your fingertip
across the pad, the pointer (also called cursor) on the screen moves
accordingly. When your finger reaches the edge of the pad, simply
relocate yourself by lifting the finger and placing it on the other side of
the pad.
Here are some common terms that you should know when using the
touchpad:
Operating Your Computer
2-9
Term
Action
Point
Move your finger on the pad until the cursor points to the
selection on the screen.
Click
Press and release the left button.
–or–
Tap gently anywhere on the pad.
Doubleclick
Press and release the left button twice in quick succession.
–or–
Tap twice on the pad rapidly.
Drag
and
drop
Press and hold the left button, then move your finger until you
reach your destination (drag). Finally, release the button (drop)
when you finish dragging your selection to the destination. The
object will drop into the new location.
–or–
Gently tap twice on the pad and on the second tap, keep your
finger in contact with the pad. Then, move your finger across the
pad to drag the selected object to your destination. When you lift
your finger from the pad, the selected object will drop into place.
Scroll
To scroll is to move up and down or left and right in the working
area on the screen.
To move vertically, place your finger on the right edge of the
pad and slide your finger up and down along the edge. To move
horizontally, place your finger on the bottom edge of the pad and
slide your finger left and right.
This function works only after you install the touchpad driver
supplied with the computer and it may not work for all
applications.
TABLE NOTE: If you swap the left and right buttons, “tapping” on the touchpad
as an alternative method of pressing the left button will no longer be valid.
2-10
Operating Your Computer
Configuring the Touchpad
You may want to configure the touchpad to suit your needs. For example,
if you are a left-handed user, you can swap the two buttons so that you
can use the right button as the left button and vise versa. You can also
change the size of the on-screen pointer, the speed of the pointer, and so
on.
To configure the touchpad, you can use the standard Microsoft or IBM
PS/2 driver if you are using Windows. However, you can install the
touchpad driver supplied with your computer to take advantage of more
powerful features. (For information on installing the driver, see “How to
Use the Driver CD” in Chapter 6.)
Operating Your Computer
2-11
Using the Touchscreen (option)
CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the
touchscreen. Doing so may damage the touchscreen surface. Use the included
touchscreen pen (option) located on the handle.
The touchscreen is a touch-sensitive device that allows you to
communicate with the computer by controlling the location of the pointer
on the screen and making selection with the buttons.
The touchscreen needs a special device driver support that allows you to
easily use the computer without a mouse or touchpad. (For information
on installing the driver, see Chapter 6.)
Here are some common terms that you should know when using the
touchscreen:
Term
Action
Click/Point
Tap gently on the touchscreen.
Double-click
Tap twice on the touchscreen rapidly.
Drag and
drop
Press lightly on the touchscreen and move your finger
until you reach your destination (drag). Finally, release
your finger (drop) when you finish dragging your selection
to the destination. The object will drop into the new
location.
Scroll
To scroll is to move up and down or left and right in the
working area on the screen.
To move vertically, place your finger on the right edge of
the touchscreen and slide your finger up and down along
the edge. To move horizontally, place your finger on the
bottom edge of the touchscreen and slide your finger left
and right.
This function works only after you install the touchscreen
driver supplied with the computer and it may not work for
all applications.
2-12
Operating Your Computer
Using the Hard Disk Drive
Your computer comes with a removable hard disk drive as drive C. A
hard disk drive is a storage device with non-removable, rotating,
magnetic storage platters inside it. It is where your operating system and
application software programs are stored.
Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics) hard
disk drive. This type of drive embodies the latest in fast, reliable mass
storage by integrating all the control circuitry necessary for operation
directly onto the drive itself. This allows the drive manufacturer to
carefully optimize drive performance.
The system comes with a built-in heater that automatically turns on for
low temperature operation. The HDD heater on indicator blinks red when
heater is on.
CAUTION:
?? Make regular backups of your data files from your hard disk drive to floppy disks or
other storage media.
?? Never try to remove or install the hard disk drive while the computer is powered on.
Doing so can result in loss of data, and can damage the computer and the hard disk
drive’s sensitive circuitry.
?? Never turn off or reset the computer while the hard disk drive in-use indicator is on.
To install a hard disk drive:
1. Make sure that system power is off.
2. Locate the hard disk drive slot on the left side of the system.
3. Open the hard disk drive slot cover by pressing on both sides of the
release latch using your thumb and index fingers.
4. Place the hard disk drive into the metal shield and tighten the four
screws.
5. Slide the HDD module into the slot until it reaches the end.
6. Close the hard disk drive slot cover to secure the HDD module.
NOTE: Before removing the hard disk drive, make sure to power down the system first.
Operating Your Computer
2-13
Using the Optical Drive
Depending on the model, your computer comes with a CD, DVD dual
recorder, or Combo drive located on the left side of the computer. This
drive is usually configured as drive D.
The drive uses removable 5.25-inch silver discs, which look like standard
music CDs. It is an ideal medium to use for distributing multimedia
because of the huge amount of data that a disc can store.
Depending on the model, your drive is one of the following:
??
CD drive can read CDs, audio CDs, CD-R, and CD-RW discs.
??
Combo drive can work both as a CD drive, DVD drive and CD-RW
drive.
??
DVD RW drive can work as a Combo drive and DVD –RW /
DVD +RW / DVD Multi / DVD Dual / Super Multi drive.
NOTE: If the CD/Combo/DVD RW drive would be operating for more than half an hour
(such as showing a DVD title), use the AC power source instead of the battery. If not,
the battery may run out of power before the operation is complete.
CAUTION:
1. When inserting a CD, do not use force.
2. Make sure the CD is correctly inserted into the tray, and then close the tray.
3. Do not leave the CD tray open. Also, avoid touching the lens in the tray with your
hand. If the lens becomes dirty, the CD may malfunction.
4. Do not wipe the lens using materials with rough surface (such as paper towel).
Instead, use a cotton swab to gently wipe the lens.
FDA regulations require the following statement for all laser-based devices:
“Caution, Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.”
NOTE: The CD/Combo/DVD RW drive is classified as a Class 1 laser product. This
label is located on the CD/Combo/DVD RW drive.
2-14
Operating Your Computer
NOTE: For Combo/DVD RW drive only.
This product incorporates copyright protection technology that is protected by method
claims of certain U.S. patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
Installing the CD/Combo/DVD RW Drive
To install the CD/Combo/DVD RW drive:
1. Open the optical drive bay cover by pressing on both sides of the
release latch using your thumb and index fingers.
2. Insert the CD/Combo/DVD RW drive into the optical drive bay
located on the left side of the computer.
3. Close the optical drive bay cover to secure the CD/Combo/DVD RW
drive in place.
To remove the CD/Combo/DVD RW drive:
1. Open the optical drive bay cover by pressing on both sides of the
release latch using your thumb and index fingers.
2. Gently place the computer upside down.
3. Lift up the handle of the optical drive release knob and turn it
counter-clockwise. The CD/Combo/DVD RW drive will slide out
partially. Gently pull on it to remove it.
Operating Your Computer
2-15
Lift up and turn counter-clockwise
Inserting and Removing a Disc
Follow this procedure to insert or remove a disc.
1. Turn on the computer.
2. Open the optical drive bay cover by pressing on both sides of the
release latch using your thumb and index fingers.
3. Press the eject button and the CD tray will slide out partially. Gently
pull on it until it is fully extended.
4. To insert a disc, place down the disc in the tray with its label facing
up. Slightly press the center of the disc until it clicks into place.
To remove a disc, hold the disc by its outer edge and lift it up from
the tray.
5.
Gently push the tray back into the drive.
NOTE: In the unlikely event that you are unable to release the CD tray by pressing the
eject button, you can manually release the disc. (See “Optical Drive Problems” in
Chapter 8.)
2-16
Operating Your Computer
Using the Video Features
The video subsystem of your computer features:
??
14.1/15-inch TFT (Thin-Film Transistor) color LCD display with
1024× 768 XGA (Extended Video Graphics Array) resolution.
??
64 MB integrated video memory.
??
Simultaneous display on LCD and external monitor, which is useful
when you have a presentation as you can control the screen from your
computer and face the audience at the same time.
??
Dual view capability, which allows you to expand your desktop on
the screen to another display device so that you have more desktop
space to work on.
??
Power Management.
??
Touchscreen function (option).
??
High contrast LCD display (option).
NOTES:
?? Before using the dual view capability, the video driver supplied with your computer
must be installed.
?? The computer enters Standby or Hibernation mode when the LCD is closed. If you
want to use the computer with the LCD closed, set None to the “When I close the lid
of my portable computer” option in the Power Management Properties. Thus the
computer does not enter Standby or Hibernation mode when the LCD is closed.
Configuring the Display Modes
NOTES:
?? To take advantage of the enhanced video capabilities, the video driver supplied
with your computer must be installed.
?? When using CRT only, the resolution would depend on the supported resolution by
the CRT.
Operating Your Computer
2-17
Your computer has been set to a default resolution and number of colors
before shipment. You can view and change display settings through your
operating system. See your operating system documentation or online
help for specific information.
For displaying in higher resolutions, you can connect an external CRT
monitor that supports higher resolutions. (See “Connecting an External
Monitor” in Chapter 4 for more information.)
The following table lists the display modes supported by your computer.
Display Mode
Resolution
800× 600
1024× 768
LCD Only CRT Only Simultaneous Display
Colors
16-bit
32-bit
16-bit
32-bit
TABLE NOTES:
?? 16-bit = High Color or 65,536 (64 K) colors; 32-bit = True Color 16,770,000 (16 M)
colors.
?? When using CRT only, the resolution would depend on the supported resolution by
the CRT.
2-18
Operating Your Computer
Using the Audio Features
NOTES:
?? To take advantage of the enhanced audio capabilities, the audio driver supplied
with your computer must be installed (see chapter 6 for details).
?? If you experience interference while recording, try lowering the microphone
recording volume.
The audio subsystem of your computer features:
??
Digital audio and analog mixing functions required for recording and
playing sound on your computer
??
Microsoft Windows Sound System support
??
A set of speakers (?) on the bottom side, and
??
External audio connectors (?)
Ways of playing and recording sound vary with the operating system
used. See your operating system documentation or online help for
specific information.
Operating Your Computer
2-19
Connecting Audio Devices
For higher audio quality, you can send or receive sound through external
audio devices.
??
Microphone Connector (
) can be connected to an external
microphone for recording voice or sound.
??
Audio Output Connector (
) can be connected to the line-in
connector of powered speakers with built-in amplifiers, headphones,
or earphone set. This connector is compliant with S/PDIF
(Sony/Philips Digital InterFace). You can connect audio equipment
with S/PDIF to the computer. S/PDIF is a newer audio transfer file
format that ensures a high qua lity digital audio output through optical
fibers.
NOTE: When using external speakers/headphones or microphone, you cannot use the
internal one.
2-20
Operating Your Computer
Using the Communication Features
Using the LAN
NOTE for Windows 2000: To take advantage of the LAN (Local Area Network)
feature, the LAN driver supplied with your computer must be installed.
The internal 10/100Base-T Ethernet module allows you to connect your
computer to a network. It supports data transfer rate up to 100 Mbps.
To connect the network cable to the LAN module, connect one end of the
LAN cable to the RJ-45 connector on the computer and the other end to
the network hub.
LAN cable
Using the Wireless LAN (WLAN)
An internal Mini PCI wireless LAN (Intel Centrino platform) module
have been pre-installed by your computer manufacturer at the factory.
This allows you to access corporate networks or the Internet in a wireless
environment.
Operating Your Computer
2-21
To take advantage of the WLAN feature, make sure that the WLAN
driver is installed correctly. (See Chapter 6 for more information.) If your
WLAN module was provided by your dealer instead of the computer
manufacturer, contact your dealer for the correct driver to use.
Configuring the WLAN
After driver installation, you can use the WLAN utility to configure and
monitor your WLAN connection. If you are using Windows XP, you can
also use its built-in WLAN utility. Follow this procedure to launch the
WLAN utility in Windows XP:
1. Select Control Panel from the Start menu.
2. Click Network and Internet Connections .
3. Click Network Connections , then double -click the Wireless
Network Connection icon .
4. Click Properties in the Wireless Network Connection Status
dialog box.
5. You can configure your WLAN settings in the Wireless Network
Connection Properties dialog box.
Turning Off/On the WLAN Radio
NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless
devices in aircraft as this may interfere with flight safe ty. Remember to select turn off
wireless LAN when using your computer in the airplane.
Your computer has a built-in Fn+F11 hot key to switch the WLAN radio
on/off (see “Hot Keys” in chapter 2).
Both Windows XP WLAN utility and the Fn+F11 hot key must be on for
the WLAN function to work. The WLAN indicator (
) glows to
indicate that the computer is ready for WLAN connection.
To turn off the WLAN function, either press Fn+F11 or turn off the
WLAN utility.
It takes approximately 30 seconds for your computer to make a successful
WLAN connection and approximately 10 seconds to disconnect.
2-22
Operating Your Computer
Using the Modem
NOTE: To take advantage of the modem feature, the modem driver supplied with your
computer must be installed.
The internal 56 K fax/data modem allows you to use the telephone line to
communicate with others by fax, email, or connect to an online service or
bulletin board.
To connect the telephone line to the modem, connect one end of the
modem cable to the RJ-11 connector on the computer and the other end to
the phone line.
Modem cable
NOTES:
?? When using communication software, you may have to disable power
management.
?? Set the COM port of the modem to COM3.
?? Set parameters such as modem speed (baud rate) and line type (pulse dialing or
tone dialing).
?? Do not enter Standby mode when using communication software.
Operating Your Computer
2-23
CHAPTER
Managing Power
Your computer operates either on external AC power or internal battery
power.
This chapter tells you how you can effectively manage power. To
maintain optimal battery performance, it is important that you use the
battery in the proper way.
The topics in this chapter include:
??
What is an AC adapter
??
How to charge the battery pack
??
When and how to initialize the battery pack
??
How to check the battery level
??
How to replace the battery pack
??
What happens when the battery is low and what actions to take
??
What is Power Management
??
How to save power
AC Adapter
CAUTION:
?? The AC adapter is designed for use with your computer only. Connecting the AC
adapter to another device can damage the adapter.
?? The AC power cord supplied with your computer is for use in the country where you
purchased your computer. If you plan to go overseas with the computer, consult
your dealer for the appropriate power cord.
?? When you disconnect the AC adapter, disconnect from the electrical outlet first and
then from the computer. A reverse procedure may damage the AC adapter or
computer.
?? When unplugging the connector, always hold the plug head. Never pull on the cord.
The AC adapter serves as a converter from AC (Alternating Current) to
DC (Direct Current) power because your computer runs on DC power,
but an electrical outlet usually provides AC power. It also charges the
battery pack when connected to AC power.
The AC adapter operates on any voltage in the range of 100 ~ 240 V AC.
3-2
Managing Power
Battery Pack
The battery pack is the internal power source for the computer. It is
rechargeable using the AC adapter.
The operating time of a fully charged battery pack depends on how you
are using the computer. When your applications often access peripherals,
you will experience a shorter operating time.
NOTE: Care and maintenance information for the battery is provided in the “Battery
Pack Guidelines” section in Chapter 7.
Charging the Battery Pack
NOTES:
?? Charging will not start if the battery’
s temperature is below 0 ?C (32 ?F) or above
50 ?C (122 ?F).
?? The charging process will stop and the Battery Charge Indicator flashes amber
when the battery’s temperature gets above 60 ?C (140 ?F). If this happens, the
battery pack may be damaged. Please contact your dealer.
?? During charging, do not disconnect the AC adapter before the battery has been fully
charged; otherwise you will get a prematurely charged battery.
To charge the battery pack, connect the AC adapter to the computer and
an electrical outlet. The Battery Charge Indicator (
) on the computer
glows amber to indicate that charging is in progress. You are advised to
keep the computer power off while the battery is being charged. When the
battery is fully charged, the Battery Charge Indicator glows green.
It takes approximately 150 minutes (2.5 hours) to charge the battery pack
when the computer is off, and 350 minutes (5.8 hours) to fully charge the
battery pack when the computer is on.
CAUTION: After the computer has been fully recharged, do not immediately disconnect
and reconnect the AC adapter to charge it again. Doing so may damage the battery.
NOTE: The battery level may automatically lessen due to the self- discharge process
(0.21% per day), even when the battery pack is fully charged (100%). This happens no
matter if the battery pack is installed in the computer.
Managing Power
3-3
Initializing the Battery Pack
You need to initialize a new battery pack before using it for the first time
or when the actual operating time of a battery pack is much less than
expected.
Initializing is the process of fully charging, discharging, and then
charging. It can take several hours.
1. Make sure the computer power is turned off. Connect the AC adapter
to fully charge the battery pack.
2. After the battery pack is fully charged, turn on the computer.
3. Disconnect the AC adapter and leave the computer on until the
battery is fully discharged. The computer will shut down
automatically.
4. Connect the AC adapter to fully charge the battery pack.
Checking the Battery Level
When two batteries exist on the system, the battery’s discharge sequence
is from the secondary battery (located on the optical drive bay) to the
primary battery (located on the right side). When the battery charge on
the secondary battery falls below 5 %, then power usage will switch to the
primary battery. When the battery charge on the primary battery falls
below 5 %, then system will shutdown.
NOTE: Any battery level indication is an estimated result. The actual operating time can
be different from the estimated time, depending on how you are using the computer.
You can check the approximate battery level using the battery meter
function of the operating system. To read the battery level in Windows,
click the
icon on the taskbar. (Click the
icon if the computer is
using AC power.)
3-4
Managing Power
Using the Primary Battery Pack
CAUTION:
?? There is danger of explosion if the battery is incorrectly replaced. Replace the
battery only with the computer manufacturer’s optional battery packs. Discard used
batteries according to the dealer’s instructions.
?? Do not attempt to disassemble the battery pack.
To install the primary battery pack, follow these steps:
1. Locate the primary battery slot on the right side of the system.
Primary battery slot
2. Open the slot cover by pressing on both sides of the release latch
using your thumb and index fingers.
3. Slide the primary battery pack all the way into the slot. Make sure to
observe the correct orientation (the ribbon strip must face outward for
future battery back removal).
4. Close the slot cover to secure the primary battery pack.
Managing Power
3-5
Using the Secondary Battery Pack
If you often rely on battery power for a long period of time while
traveling, you may consider the purchase of an additional battery pack
from your dealer and keep it with you in a fully charged state as a backup.
To install the secondary battery pack, follow these steps:
1. Locate the optical drive slot on the left side of the system.
2. Open the slot cover by pressing on both sides of the release latch
using your thumb and index fingers.
3. Gently place the computer upside down.
4. Lift up the handle of the optical drive release knob and turn it
counter-clockwise. The CD/Combo/DVD RW drive will slide out
partially. Gently pull on it to remove it.
Lift up and turn counter-clockwise
5. Slide the secondary battery pack all the way into the slot. Make sure
to observe the correct orientation (the ribbon strip must face outward
for future battery pack removal).
6. Close the slot cover to secure the secondary battery
3-6
Managing Power
NOTE: The system supports the battery hot- swap function, providing you the ability to
replace the battery even during system on. Hot swap means that you can remove the
secondary battery pack and replace it with another one without significant interruption
to the system (without turning off the system).
Battery Low Signals and Actions
Battery Low occurs when the battery has approximately 10 % (Windows
default setting) of its charge remaining. The computer gives warning
beeps or messages and the Battery Power Indicator (
(orange) to alert you to take actions.
) blinks amber
NOTE: You can set up your threshold and signals of Battery Low under Windows.
Immediately save your data upon Battery Low. The remaining operating
time depends on how you are using the computer. If you are using the
audio subsystem, hard or optical drives, the battery might run out of
charge very quickly.
Always respond to Battery Low by placing your computer on Standby or
Hibernation mode, turning off the computer, or connecting the AC
adapter.
If you do not take any action, the computer will automatically hibernate
and turn off.
CAUTION:
?? If you are using a flash PC card, do not access the card during battery low periods.
This is because the access may take longer than the time it takes the battery to run
out of charge, thus making your access to the card unsuccessful.
?? If you fail to save your data when the battery completely runs out of charge, then
you lose your data.
Managing Power
3-7
Power Management
Your computer supports ACPI (Advanced Configuration and Power
Interface) for power management. The power management feature allows
you to reduce the power consumption for energy saving.
With an ACPI-compliant operating system such as Windows 2000 and
Windows XP, power supply to different computer components is
controlled on an as-needed basis. This allows maximum power
conservation and performance at the same time.
In general, Windows’ power management works in this way:
What…
When…
Power to the hard disk is turned off
When the hard disk has been idle for a
set period.
Power to the display is turned off
When the display has been idle for a set
period.
The computer enters Standby mode. When the entire system has been idle
The hard disk and display are turned for a set period.
off and the entire system consumes
When you press Fn+F10. *
less power.
When you close the cover. *
When you press the power button. *
The computer enters Hibernation
mode. (See the next subsection for
more information.)
When you press the power button. *
When you press Fn+F10. *
When you close the cover. *
* depends on your settings in Windows.
For detailed information on power management, see Windows’ Help.
3-8
Managing Power
Hibernation
Hibernation is a very useful feature. People frequently open many
applications when they use computers. It takes some time to get all these
applications open and running, and normally they all have to be closed
before the system can be turned off.
When you use the hibernation feature, you do not have to close the
applications. The computer stores the state of your computer to a file on
the hard disk and then shut down. The next time you turn on your
computer, you return to exactly where you left off.
Managing Power
3-9
Power-Saving Tips
In addition to your computer’s automatic power manageme nt, you can do
your part to maximize the battery’s operating time by following these
suggestions.
3-10
??
Do not disable Power Management.
??
Decrease the LCD brightness to the lowest comfortable level.
??
Disable the parallel and serial ports if no devices are connecte d to
these ports. (See “Advanced Menu” in Chapter 5.)
??
If you work with an application that uses the PC card or features
wireless connectivity (LAN), exit the application when you finish
using it.
??
If you have a PC card installed, remove it when not in use. Some PC
cards drain power even while they are inactive.
??
Turn off the computer when you are not using it.
Managing Power
CHAPTER
Expanding Your Computer
You can expand the capabilities of your computer by connecting other
peripheral devices. When using a device, be sure to read the instructions
accompanying the device together with the relevant section in this
chapter.
This chapter gives guidelines on installing and using these devices:
??
External monitor
??
USB device
??
PS/2 keyboard and mouse
??
Parallel device
??
Serial device
??
IR device
??
PC card
Connecting an External Monitor
If you want the benefits of a larger display screen with higher resolution,
you can connect an external CRT monitor to your computer.
Follow this procedure to connect an external monitor:
1. Make sure that the computer is not turned on.
2. Plug the monitor’s D-type signal connector to the computer’s VGA
port.
Connect to external monitor
3. Plug one end of the monitor’s power cord into the power socket on
the monitor and the other end to an electrical outlet.
4. To use the monitor, turn on the monitor before turning on the
computer.
5. The monitor should respond by default. If not, you can switch the
display to the monitor or to both (simultaneous display) by pressing
Fn +F9. In Windows, you can also change the display through the
settings in Display Properties.
6. You can change display settings through your operating system. See
your operating system documentation or online help for specific
information.
4-2
Expanding Your Computer
CAUTION: Do not disconnect the external monitor while the computer is in Standby
mode or Hibernation mode. If no external monitor is connected when the computer
resumes, the LCD remains blank and the output is not displayed.
Expanding Your Computer
4-3
Connecting a USB Device
NOTE: To take advantage of the USB 2.0 feature, the USB 2.0 driver supplied with your
computer must be installed (see chapter 6).
Your computer has two USB ports that supports transfer rates up to 12
MB/s for USB 1.1 devices and 480 MB/s for USB 2.0 devices, such as
digital camera, scanner, printer, modem, and mouse.
USB is specified to be an industry standard extension to the PC
architecture. It supports “Plug-and-Play” technology so you can install
and remove USB devices without turning off the computer. With its
multiple connection capability, up to 127 devices can be connected in a
daisy-chain configuration. In addition, you can use a USB hub that
converts a single USB connector into multiple ports where USB devices
can be connected.
To connect a USB device, simply plu g the device cable to one of the USB
ports.
Connect to USB device(s)
4-4
Expanding Your Computer
Connecting the PS/2 Keyboard and Mouse
If you want the benefits of a full-size keyboard or an external mouse, you
can connect a PS/2 keyboard/mouse to your computer.
When an external keyboard/mouse is connected, you can use both the
external keyboard/mouse and the internal keyboard/touchpad at the same
time.
To connect an external keyboard/mouse, simply plug its cable to the PS/2
port on the rear of the computer.
Connect to PS/2 mouse/keyboard
NOTE: If you wish to use a PS/2 mouse and keyboard at the same time, you need to
buy a Y-cable adapter.
Expanding Your Computer
4-5
Connecting a Parallel Device
Your computer has a parallel port for connecting a parallel device such as
printer. The port supports ECP (Extended Capabilities Port) and EPP
(Enhanced Parallel Port) modes that turn the standard parallel port into a
high-speed bi-directional peripheral port.
Follow this procedure to connect a parallel device:
1. Make sure that the “LPT Port” item is set properly in the BIOS Setup
program. (See “Advanced Menu” in Chapter 5 for information.)
2. Make sure the computer is not turned on.
3. Plug the parallel device’s cable to the computer’s parallel port.
Connect to parallel device
4. If the parallel device has independent power, plug its power cord into
an electrical outlet.
5. If the parallel device has its own power switch, turn on the printer
before turning on the computer.
4-6
Expanding Your Computer
Connecting a Serial Device
Your computer has a serial port for connecting a serial device such as an
external modem.
Follow this procedure to connect a serial device:
1. Make sure the “COM Ports” item is set properly in the SCU program.
(See “Advanced Menu” in Chapter 5 for information.)
2. Make sure the computer is not turned on.
3. Plug the device cable to the serial port on the rear of the computer.
4. Turn on the computer.
Connect to serial device
NOTE: Portable modems that derive power through the serial port cannot be used with
the computer. Instead, use a modem that is powered by its own internal battery or
external AC power.
Expanding Your Computer
4-7
Connecting an IR Device
Your computer has an IR (infrared) port for connecting an
infrared-equipped device wirelessly such as another computer, printer, or
PDA (Personal Digital Assistant).
Follow this procedure to connect an IR device:
1. Under Windows, make sure that the IrDA Fast Infrared Port is set to
HP HSDL-2300/3600.
2. Make sure that the “COM Ports” and its “Mode Setting For COM B”
items are set properly in the SCU program. (See “Advanced Menu”
in Chapter 5 for information.)
3. When using the IR port:
Place the transmitting device where its IR port faces the IR port of
your computer within the effective range ? within ?20-degrees
vertical angle and within ?20-degrees horizontal angle at no greater
than 0.8~1.0 meter distance.
Place the receiving device where the IR port of your computer faces
its IR port within the effective range ? within ?15-degrees vertical
angle and within ?15-degrees horizontal angle at no greater than
0.8~1.0 meter distance.
4. To take advantage of the IR communications, you need a third party
software.
NOTES: During infrared communication, take note of the following:
?? Do not move the computer and IR device.
?? Do not enter Standby mode.
?? Do not use a cell phone or another IR device near the computer.
?? Avoid strong light such as sunlight or fluorescent light.
?? Disable the screen saver.
4-8
Expanding Your Computer
Connect to IR device
Expanding Your Computer
4-9
Using PC Cards
Your computer has a PC card slot.
PC cards are credit card-sized peripheral products based on the standards
developed by PCMCIA (Personal Computer Memory Card International
Association). PCMCIA is a non-profit association for promoting the
interchangeability among mobile computers where ruggedness, low
power, and small size are critical.
PC Card Type
Your computer’s PC card slot can accommodate two type II card or one
type III cards. Typical type II/III cards are flash memory, SRAM,
modem, LAN, and SCSI cards.
CardBus Support
Your computer’s PC card slot supports CardBus specifications. CardBus
is the 32-bit version of PC card technology. It allows speeds of up to 133
Mbps at 33 MHz. Typical applications are SCSI host bus and high-speed
network cards.
Inserting and Removing a PC Card
NOTES:
?? Some PC cards require additional system resources. Before using such PC card,
you may have to free other system resources for the PC card.
?? Although some PC cards can be inserted and removed without turning off the
computer, you cannot remove or install PC cards during Standby mode.
To insert a PC card:
1. Locate the PC card slot on the left side of the computer.
2. Slide the PC card, with its label facing up, into the slot until the eject
button pops out.
4-10
Expanding Your Computer
Eject Button
3. When a new card is seated, the computer will detect it and try to
install the appropriate driver. Follow the on-screen instructions to
complete the process.
To remove a PC card:
1. Double-click on the Safely Remove Hardware
icon found on
the Windows XP taskbar and the Safely Remove Hardware window
appears on screen.
2. Select (highlight) the PC card from the list to disable the card.
3. Push the eject button and the card will slide out slightly.
4. Pull the card out of the slot.
Expanding Your Computer
4-11
System Memory Upgrade
You can upgrade your computer by changing system memory to a
maximum of 2 GB on the two 200-pin PC2100/PC2700 DDR SO-DIMM
slots.
To install the SO-DIMM :
1. Carefully place the notebook computer upside down.
2. Remove the ten screws to detach the SO-DIMM compartment cover.
4-12
Expanding Your Computer
3. Remove the long rubber cushion on the left side and two short rubber
cushions on the right side.
1 long rubber cushion
2 short rubber cushions
4. To install the SO-DIMM, match the SO-DIMM's notched part with
the socket's projected part and firmly insert the SO-DIMM into the
socket at a 20-degree angle. Then push down until the retaining clips
lock the SO-DIMM into position.
5. Replace the long rubber cushion on the left side and two short rubber
cushions on the right side.
6. Replace the SO-DIMM compartment cover and secure with ten
screws.
Expanding Your Computer
4-13
4-14
Expanding Your Computer
CHAPTER
Setup Configuration Utility (SCU)
SCU is a program for configuring the BIOS (Basic Input/Output System)
settings of the computer.
BIOS is a layer of software, called firmware, that translates instructions
from other layers of software into instructions that the computer hardware
can understand. The BIOS settings are needed by your computer to
identify the types of installed devices and establish special features.
This chapter tells you how to use the SCU program.
When and How to Use the SCU Program
When to Use
You need to run the SCU program when:
??
You see an error message on the screen requesting you to run Setup.
??
You want to restore the factory default settings.
??
You want to modify some specific settings according to the
hardware.
??
You want to modify some specific settings to optimize system
performance.
Starting SCU
NOTES:
?? The Setup screens shown in this chapter are for your reference only. The actual
items or settings on your computer may differ.
?? The Setup program may have been updated after the publication of this manual.
?? The settings you select in your operating system might override similar settings in
Setup.
To run SCU, press F2 when the prompt appears in the lower left corner of
the screen during system startup. The prompt shows up on the screen for
only a few seconds. You must press F2 quickly. The SCU menu appears
as shown next.
5-2
Setup Configuration Utility (SCU)
The menu can be divided into four areas:
??
On the top line is the menu bar containing the titles of the available
menus. Each menu title br ings a specific menu.
??
The center left column of the menu contains information regarding
the current settings of the system. If you open a pull-down menu and
select an item that provides multiple options, the left column will
display a submenu where you can make further selections.
??
The right column of the menu contains details of the CPU and system
memory.
??
The bottom lines of the menu provide keyboard instructions for
moving around and making selections. When a menu item is
highlighted, more detailed information is given.
Setup Configuration Utility (SCU)
5-3
Moving Around and Making Selections
A brief description of keyboard usage is listed next:
Key
Function
? ,?
Selects a menu title.
?,?
1) Selects an item or option.
2) Brings up/down the value.
Enter
1) Brings up the sub-menu when available.
2) Opens or closes the options window when an item is selected.
Tab
Jumps from one item to another.
Esc
1) Exits the SCU program.
2) Returns to the previous menu if in a sub-menu.
3) Closes the options window if one is open.
NOTE: You are advised to use the touchpad (if enabled) as it is more straightforward
than using the keyboard.
5-4
Setup Configuration Utility (SCU)
Main Menu
Date and Time
Setup Configuration Utility (SCU)
5-5
Sets the system time (Hour, Minute, Second) and date (Year, Month,
Day).
Internal Numlock
Sets if you can enter a number when Num Lock is turned on. When this
item is enabled and Num Lock is turned on, you can press a letter key to
enter a number, and press and hold Fn , then a letter key to enter a letter.
When this item is disabled and Num Lock is turned on, the above method
works oppositely. When Num Lock is turned off, this item does not
function. A check mark (?) indicates enabled; an underline (_) indicates
disabled.
USB Emulation
Enables or disables the system’s support for the USB port in DOS mode.
A check mark (?) indicates enabled; an underline (_) indicates disabled.
5-6
Setup Configuration Utility (SCU)
Advanced Menu
Geyserville Support
Setup Configuration Utility (SCU)
5-7
Allows maximum CPU performance when using AC/car power but
minimum CPU performance when using battery power. The available
options are Enabled and Disabled . Make sure that your CPU supports
this function.
Shared Video Memory
Allows you to set the shared memory size of the video controller. The
available options are 4M, 8M, 16M, and 32M.
5-8
Setup Configuration Utility (SCU)
COM Ports
Allows you to configure the COM ports of the computer.
COM1/2/3/4 Settings sets the I/O (Input/Output) address and the
Interrupt ReQuest line (IRQ) settings of the COM ports. The options
are Disabled; COM1, 3F8, IRQ4; COM2, 2F8, IRQ3; COM3, 3E8,
IRQ6; COM4, 2E8, IRQ11.
Mode Setting for COM B sets the communication compatibility
mode according to the type of the IR device to be connected. The
options are IrDA (HPSIR) and Fast IR. This item is not valid for
setting if the COM1/2/3/4 Settings item is set to Disabled.
Setup Configuration Utility (SCU)
5-9
LPT Port
This item configures the parallel port of the computer.
Port Address sets the I/O address and the Interrupt ReQuest line
settings of the parallel port. The options are None; LPT1, 378, IRQ7;
LPT2, 278, IRQ5; and LPT3, 3BC, IRQ7.
Port Definition sets the operating mode for the parallel port
according to the type of the parallel device to be connected. Your
system supports EPP (Enhanced Parallel Port) and ECP (Extended
Capabilities Port) standards, which turn the standard parallel port
into a high-speed bi-directional peripheral port. The options are
Standard AT (Centronics), Bidirectional (PS -2), Enhanced Parallel
(EPP), and Extended Capabilities (ECP). This item is not valid for
setting if the Port Address item is set to None.
MC97 Controller
Enables or disables the system’s support for PCI modem device. A check
mark (?) indicates enabled; an underline (_) indicates disabled.
5-10
Setup Configuration Utility (SCU)
HDD Heater
Sets if the system automatically turns on the built-in hard disk drive
heater for low temperature operation. A check mark (? ) indicates
enabled, while underline (_) indicates disabled.
NOTE: Disable this item to conserve energy when using battery power.
Setup Configuration Utility (SCU)
5-11
Security Menu
Power-on Password
5-12
Setup Configuration Utility (SCU)
Allows you to set the password for booting-up your system. When typing
the password, first make sure that Num Lk is off, and then type the
password in the entry fields and press Enter. Confirm your password by
typing it again and pressing Enter. If the Enable Password to Power-on
sub-item is enabled, the power-on password is always required to boot the
computer.
SCU Password
Allows you to set the password for entering SCU Setup. When typing the
password, first make sure that Num Lk is off, and then type the password in
the entry fields and press Enter. Confirm your password by typing it again
and pressing Enter. If the Enable SCU Password sub-item is enabled, the
SCU password is always required to enter SCU Setup.
Hard Disk Encryption
Enables or disables hard disk drive encryption (including boot sector,
operating system, temporary and swap files). Attempts to circumvent
security by booting from a floppy disk or by removing the hard drive to
be read on a different machine would prove futile since the entire content
of the hard drive is encrypted. A checkmark (?) indicates enabled, while
an underline (_) indicates disabled.
Setup Configuration Utility (SCU)
5-13
CAUTION: You must enable this option first before formatting your hard disk drive
(HDD). Upon enabling this function, you will be asked to type in your HDD key. You
must remember the HDD key as you need to type it every time you boot up your
system.
If you did not enable this option and have already formatted your hard disk, then you
must “GHOST” the contents of your hard disk to another storage media before you can
enable this option for the first time.
IMPORTANT: If you should lose the HDD key, your dealer or the computer
manufacturer will not be responsible for any loss of data. You will need to re-format
your hard disk and thereby, lose all your original data.
Hard Disk Boot Sector
Sets if a warning message will appear when the hard disk boot sector
(partition table ) has been changed. A checkmark (?) indicates enabled,
while an underline (_) indicates disabled.
CAUTION: Set this item to disabled before installing an operating system, running
Fdisk or Format program. Otherwise, the intended action will fail.
5-14
Setup Configuration Utility (SCU)
Boot Menu
Boot Sequence
Setup Configuration Utility (SCU)
5-15
Sets the first, second, third, and fourth booting device. The system will
try to boot from the first device but if it is not available, will try the next
boot device. If you set the first boot device to LAN Boot, the system will
boot from the LAN server first. The options are Hard Disk Drive,
CD-ROM Drive, Floppy Disk Drive, and LAN Boot.
NOTE: If you set all booting options to the same device, then the computer will try to
boot from that device only.
5-16
Setup Configuration Utility (SCU)
Exit Menu
Save Changes and Exit saves the changes you have made and exit the
SCU program.
Discard Changes and Exit exits the SCU program without saving the
changes you have made.
Get Default Values loads factory default values for all the items.
Load Previous Values restores previous values for all the items.
Setup Configuration Utility (SCU)
5-17
CHAPTER
Installing Software Drivers
To take full advantage of the unique features of your computer, some
operating systems require custom software, known as drivers, to be
installed.
If you purchased the computer with Windows pre-installed, your dealer
may have already installed the drivers. If not, you need to install the drivers
using the driver CD supplied with your computer.
This chapter describes how to install the drivers.
How to Use the Driver CD
NOTES:
? The drivers may have been updated after this manual was published. For driver
upgrade, please contact your dealer.
? You can always find README or document files on the driver CD. These files
contain the latest information from the software supplier. Please read the files
together with this chapter.
? This driver CD supports Windows 2000 and Windows XP only. You are
recommended to install Windows 2000 Service Pack 4 when using Windows 2000
and Windows XP Service Pack 2 when using Windows XP.
? The available items may differ according to your computer model and operating
system.
? 請當安裝驅動程式時請不要移開驅動程式。
6-2
Installing Software Drivers
An autorun program is provided on the driver CD to help you easily install
the drivers. As you insert the driver CD, the autorun program
automatically starts. If you need to start the program manually, run the
Autorun.exe program from the driver CD.
安裝必要的驅動, 正義點擊特殊選擇和跟隨 onscreen 指示繼續
和完成設施。
To install the necessary driver, just click on the particular option and follow
the onscreen instructions to continue and complete installation.
Device driver
Ensures the full function of the following drivers. Install
this main driver before installing the device drivers.
Upon clicking this icon, the chipset, VGA, audio,
modem, and LAN drivers would be installed one after
the other.
DirectX 8.1
Allows you to take full advantage of the multimedia
applications. Run the file DX81NTeng.exe located
on the /Utility/DirectX/ directory on your
driver CD.
NOTE: For Windows 2000 only.
USB-to-COM
Allows you to use the optional wireless modem and
GPS features to transmit information wirelessly.
Touch Screen
Allows you to use your fingers as a pointing device on
the LCD screen (refer to the next section for further
instructions).
Installing Software Drivers
6-3
MTCCTRL
Allows you to use the built-in heater feature that
automatically turns on for low temperature hard disk
drive operation.
VGA Utility
Allows you to use the ATI M11 VGA control panel for
better display control.
WLAN Utility
Allows you to use the computer’s internal Mini PCI
WLAN card’s network function.
Shows you a list of the included drivers in this driver
CD and the version number.
ReadMe
Browse CD
Browses the contents of the CD.
Exit
Exits the driver CD installation.
Touchscreen Driver
For Windows 2000
安裝觸驅動程式, 執行以下:
1. 插入驅動程式近入磁碟機。
2. Click on “Touch Screen” and follow the onscreen instructions to
continue.
3. When finished installing, select “Yes” to reboot your system. The
driver should now be loaded.
4. After the system has finished rebooting, click on the “PenMount
Monitor” icon located on the taskbar to bring up the “PenMount
Control Panel.”
5. Select the “Standard Calibrate” folder and click on “OK.”
6. Click on “Advanced Calibrate” button.
7. Click on the four sides (points) and the plus-sign “+” on the screen to
calibrate your touchscreen for use on the computer.
6-4
Installing Software Drivers
For Windows XP
To install the touchscreen driver, perform the following:
1. Insert the driver CD into the drive.
2. Click on “Touch Screen” and follow the onscreen instructions to
continue.
3. Click on ”Start,” then “Control Panel.”
Installing Software Drivers
6-5
4. Click on the “Performance and Maintenance” category.
5. Click on “System.”
6-6
Installing Software Drivers
6. Click on “Hardware” folder, then click on “Device Manager.”
Installing Software Drivers
6-7
7. Click on “? Unknown device,” then click on the “Properties” icon.
6-8
Installing Software Drivers
8. Click on “Reinstall Driver.”
9. When the “Hardware Update Wizard” appears, select “Install the
software automatically [Recommended],” then click on “Next.”
Installing Software Drivers
6-9
10. Click on “Continue Anyway.”
11. Click on “Finish.”
6-10
Installing Software Drivers
12. When the “PenMount DMC9000 and DMC9100 Properties” screen
appears, click on “Close” to exit the driver installation.
Installing Software Drivers
6-11
CHAPTER
Caring for the Computer
Taking good care of your computer will ensure a trouble -free operation
and reduce the risk of damage to your computer.
This chapter gives you guidelines covering these areas of maintenance:
??
How to protect the computer
??
What to note when using and storing the computer
??
How to clean the computer
??
What to note when using the battery pack
??
What to note when traveling with the computer
Protecting the Computer
To safeguard the integrity of your computer data as well as the computer
itself, you can protect the computer in several ways as described in this
section.
Using the Password
The power-on password protects your computer against unauthorized
use. If the password is set, the prompt requesting for the password
appears on the screen whenever the computer is turned on.
The password is set via the SCU program. See “Security Menu” in
Chapter 5 for instructions.
Using the Cable Lock
You can use a Kensington-type cable lock to protect your computer
against theft. The cable lock is available in most computer stores.
To use the lock, loop the lock cable around a stationary object such as a
table. Insert the lock to the Kensington lock hole and turn the key to
secure the lock. Store the key in a safe place.
Kensington lock
7-2
Caring for the Computer
Using an Anti-Virus Strategy
New viruses are always being developed nowadays and they are attacking
computers even more easily with emails so commonly used worldwide.
The Security feature of the SCU program protects the boot sector of the
hard disk. To enable the function, see “Security Menu” in Chapter 5 for
instructions.
You can also install a virus-detecting program to monitor potential
viruses that could damage your files.
Caring for the Computer
7-3
Taking Care of the Computer
Location Guidelines
??
Use the computer where the temperature is between 0 ?C (32 ?F) and
55 ?C (131 ?F).
??
Avoid placing the computer in a location subject to high humidity,
extreme temperatures, mechanical vibration, direct sunlight, or heavy
dust.
??
Do not cover or block any ventilation openings on the computer. For
example, do not place the computer on a bed, sofa, rug, or other
similar surface. Otherwise, overheating may occur that results in
damage to the computer.
??
Keep the computer at least 13 cm (5 inches) away from electrical
appliances that can generate a strong magnetic field such as a TV,
refrigerator, motor, or a large audio speaker.
??
Do not move the computer abruptly from a cold to a warm place. A
temperature difference of more than 10 ?C (18 ?F) will cause
condensation inside the unit, which may damage the storage media.
??
Do not place the computer on an unsteady surface.
General Guidelines
7-4
??
Do not place heavy objects on top of the computer as this may
damage the display.
??
The screen surface is easily scratched. Do not use paper towels to
clean the display. Avoid touching it with a ballpoint pen or pencil.
??
To maximize the life of the backlight in the display, allow the
backlight to automatically turn off as a result of power management.
Avoid using a screen saver or other software that prevents the power
management from working.
Caring for the Computer
Cleaning Guidelines
??
Never clean the computer with its power on.
??
Use a soft cloth moistened with water or a non-alkaline detergent to
wipe the exterior of the computer.
??
Gently wipe the display with a soft, lint-free cloth. Do not use alcohol
or detergent on the display.
??
Dust on the IR port can interfere with data transfer. Wipe the port
with a soft, dry cloth.
??
Dust or grease on the touchscreen can affect its sensitivity. Clean the
touchscreen by using adhesive tape to remove the dust and grease on
its surface.
Battery Pack Guidelines
??
Recharge the battery pack when it is nearly discharged. When
recharging, make sure the battery pack is fully charged. Doing so
may avoid harm to the battery pack.
??
Operate the computer with the battery pack installed even when using
external power. This ensures that the battery is fully charged.
??
If you will not be using the computer for a long period of time (more
than two weeks), remove the battery pack from the computer.
??
If you remove the battery pack, make sure the battery terminals do
not contact any conductors such as metal objects or water. Otherwise,
the battery may become unusable as a result of a short circuit.
??
If you need to store the battery pack, store it in a cool, dry place.
Never allow the temperature to exceed 70 ?C (158 ?F).
??
Do not leave the battery pack in storage for more than 3 months
without recharging it.
Caring for the Computer
7-5
When Traveling
7-6
??
Before traveling with your computer, make a backup of your hard
disk data into floppy disks or other storage devices. As an added
precaution, bring along an extra copy of your important data.
??
Make sure the battery pack is fully charged.
??
Make sure the computer is turned off.
??
Do not leave objects that will press onto the display.
??
Disconnect the AC adapter from the computer and take it with you.
Use the AC adapter as the power source and as a battery-charger.
??
Hand-carry the computer. Do not check it in as luggage.
??
Allow extra time for airport security. Many airports inspect
electronic devices carefully.
??
If you need to leave the computer in the car, put it in the trunk of the
car to avoid exposing the computer to excessive heat.
??
When going through airport security, it is recommended that you
send the computer and floppy disks through the X-ray machine (the
device you set your bags on). Avoid the magnetic detector (the device
you walk through) or the magnetic wand (the hand-held device used
by security personnel).
??
If you plan to travel abroad with your computer, consult your dealer
for the appropriate AC power cord for use in your country of
destination.
Caring for the Computer
CHAPTER
Troubleshooting
Hardware, software, or a combination of both can cause computer
problems. When you encounter any problem, it might be a typical
problem that can easily be solved.
This chapter tells you what actions to take when solving common
computer problems. It is divided into three sections:
??
Preliminary checklist
??
Solving common problems
??
Resetting the computer
Preliminary Checklist
Here are helpful hints to follow before you take further actions when you
encounter any problem:
??
Try to isolate which part of the computer is causing the problem.
??
Make sure that you turn on all peripheral devices before turning on
the computer.
??
If an external device has a problem, make sure that the cable
connections are correct and secure.
??
Make sure that the configuration information is properly set in the
SCU program.
??
Make sure that all the device drivers are correctly installed.
??
Make notes of your observations. Are there any messages on the
screen? Do any indicators light? Do you hear any beeps? Detailed
descriptions are useful to the service personnel when you need to
consult one for assistance.
If any problem persists after you follow the instructions in this chapter,
contact an authorized dealer for help.
8-2
Troubleshooting
Solving Common Problems
For easy reference, the problems are divided into these categories.
Problem Type
Go to
Battery Problems
P. 8-4
Optical Drive Problems
P. 8-4
Display Problems
P. 8-5
Hardware Device Problems
P. 8-7
Hard Disk Drive Problems
P. 8-7
Infrared Problems
P. 8-7
Keyboard, Mouse and Touchpad Problems
P. 8-8
LAN Problems
P. 8-9
WLAN Problems
P. 8-9
Modem Problems
P. 8-9
PC Card Problems
P. 8-11
Power Management Problems
P. 8-11
Printer Problems
P. 8-12
Software Problems
P. 8-12
Sound Problems
P. 8-13
Startup Problems
P. 8-13
Other Problems
P. 8-14
Troubleshooting
8-3
Battery Problems
The battery does not charge (Battery Charge indicator does not light
amber).
?? Make
sure that the AC adapter is properly connected.
?? Make
sure that the battery is not too hot or cold. Allow time for the
battery pack to return to room temperature.
?? Make
sure that the battery pack is installed correctly.
?? Make
sure that the battery terminals are clean.
The operating time of a fully charged battery becomes shorter.
?? If
you often partially recharge and discharge, the battery might not be
charged to its full potential. Initialize the battery to solve the problem.
(See “Initializing the Battery Pack” in Chapter 3 for instructions.)
The battery operating time indicated by the battery meter does not
match the actual operating time.
?? The
actual operating time can be different from the estimated time,
depending on how you are using the computer. If the actual operating
time is much less than the estimated time, initialize the battery. (See
“Initializing the Battery Pack” in Chapter 3 for instructions.)
Optical Drive Problems
The CD/Combo/DVD RW drive cannot read a disc.
?? Make
sure that the disc is correctly seated in the tray, with the label
facing up.
?? Make sure that the disc is not dirty. Clean the disc with a disc cleaning
kit, available in most computer stores.
?? Make
sure that the CD/Combo/DVD RW drive driver is installed
correctly.
?? Make
8-4
sure that the computer supports the disc or the files contained.
Troubleshooting
You cannot eject a disc.
?? The
disc is not properly seated in the drive. Manually release the disc
following the method described next:
1. Turn off the system.
2. Insert a small rod, such as a straightened paperclip, into the drive’s
manual eject hole and push firmly to release the tray.
3. Pull the tray out until fully extended, and then remove the disc.
Eject hole
Display Problems
Nothing appears on the screen.
?? If
the power-on indicator is not on, check the electrical outlet, the
plugs and power cords.
?? If
the power button does not respond to a light touch, press the button
firmly.
?? If
you are using battery power, make sure that it has a charge
remaining and that it is installed correctly.
?? During
operation, the screen may automatically turn off as a result of
power management. Press any key to see if the screen comes back.
Troubleshooting
8-5
?? The brightness level might be too low. Increase brightness by pressing
Fn+F6.
?? The
display output might be set to an external device. To switch the
display back to the LCD, press Fn +F9, or change the display through
the settings in Display Properties.
?? Reset
?? Try
the computer by pressing Ctrl+ Alt+Del keys.
turning the computer off, wait for a few seconds, then turn it back
on.
The characters on the screen are dim.
?? Adjust
the brightness and/or contrast.
Bad dots appear on the display at all times.
?? A
small number of missing, discolored, or bright dots on the screen
are an intrinsic characteristic of TFT LCD technology. It is not
regarded as a LCD defect. The Inspection Standard generally agreed
in the LCD industry allows a maximum of 8 bad dots on a unit.
Resolution cannot be adjusted to desired setting.
?? Make
sure that the video driver is installed correctly.
The external monitor displays nothing.
?? Make
sure that the monitor is turned on.
?? Make
sure that the monitor’s signal cable is properly connected.
the display to the monitor by pressing Fn +F9, or change the
display through the settings in Display Properties.
?? Switch
Simultaneous display/multi-display does not work.
?? Make
sure that you turn on the external monitor before turning on the
computer.
?? Press Fn +F9 to
toggle through the display options or change the
settings in Display Properties in Windows.
8-6
Troubleshooting
Hardware Device Problems
The computer does not recognize a newly installed device.
?? The
device may not be correctly configured in the SCU program. Run
the SCU program to identify the new type.
?? Make
sure if any device driver needs to be installed. (Refer to the
documentation that came with the device.)
?? Make
sure if the device needs any jumper or switch settings. (Refer to
the documentation that came with the device.)
?? Check
the cables or power cords for correct connections.
?? For
an external device that has its own power switch, make sure that
the power is turned on.
Hard Disk Drive Problems
The hard disk drive error message appears on the screen.
?? Insert
?? The
a bootable diskette and check the integrity of your hard drive.
hard disk drive has defects. Ask your dealer for help.
The hard disk drive operations seem slow.
?? The
data files stored on the hard disk drive may be fragmented. Use a
tool such as Window’s Disk Defragmenter to defragment the files.
The hard disk drive in-use indicator glows without blinking.
?? The
data files stored on the hard disk drive may be fragmented. Use a
tool such as Window’s Disk Defragmenter to defragment the files.
Infrared Problems
The IR port does not work.
?? Make
sure that the IR ports of the two device face each other within a
?15-degrees angle and 1 meter (3 feet) distance and there are no
obstructions in between.
Troubleshooting
8-7
?? Make
sure that the device connected is using an equivalent speed.
?? Make
sure that the IrDA Fast Infrared Port is set to HP
HSDL-2300/3600.
?? Make
sure that the IR port is set correctly in the SCU program.
?? If
you are printing to an infrared printer, make sure that the
appropriate driver is installed.
?? If
you are using any file transfer functions, make sure that both the
computer and the IR device have the appropriate software running.
?? Make
sure that there is no device radiating infrared rays, such as
remote-controlled devices or wireless headphones, near the computer
or device.
?? Make
sure that no direct sunlight or fluorescent lamps are near the
computer or device.
?? Make
sure that the IR ports are clean.
Keyboard, Mouse and Touchpad Problems
The keyboard does not respond.
?? Try
connecting an external keyboard. If it works, contact an
authorized dealer, as the internal keyboard cable might be loose.
The numeric keypad is disabled.
sure that Num Lk is switched on. (Check if the Num Lock
Indicator
glows or not.)
?? Make
The external keyboard does not work.
?? Make
sure that the keyboard cable is properly connected.
The USB mouse does not work.
?? Make
sure that the mouse cable is properly connected.
The touchpad does not work, or the pointer is difficult to control
with the touchpad.
?? Make
8-8
sure that the touchpad is clean.
Troubleshooting
LAN Problems
I cannot access the network.
?? Make
sure that the LAN driver is correctly installed.
?? Make
sure that the LAN cable is properly connected to the RJ-45
connector and the network hub.
?? Make
sure that the network configuration is appropriate.
?? Make
sure that the user name or password is correct.
WLAN Problems
I cannot use the WLAN feature.
?? Make
sure that the necessary driver(s) is correctly installed.
?? Make
sure that the WLAN feature is turned on.
Transmission quality is poor.
?? Your
computer may be in an out-of-range situation. Move your
computer closer to the Access Point or another WLAN device it is
associated with.
?? Check
if there is high interference around the environment and solve
the problem as described next.
Radio interference exists.
?? Move
your computer away from the device causing the radio
interference such as microwave oven and large metal objects.
?? Plug
your computer into an outlet on a different branch circuit from
that used by the affecting device.
?? Consult
your dealer or an experienced radio technician for help.
I cannot connect to another WLAN device.
?? Make
sure that the WLAN feature is turned on.
?? Make
sure that the SSID setting is the same for every WLAN device
in the network.
Troubleshooting
8-9
?? Your
computer is not recognizing changes. Restart the computer.
?? Make
sure that the IP address or subnet mask setting is correct.
I cannot communicate with the computer in the network when
Infrastructure mode is configured.
?? Make
sure that the Access Point your computer is associated with is
powered on and all the LEDs are working properly.
?? If
the operating radio channel is in poor quality, change the Access
Point and all the wireless station(s) within the BSSID to another radio
channel.
?? Your
computer may be in an out-of-range situation. Move your
computer closer to the Access Point it is associated with.
?? Make
sure that your computer is configured with the same security
option (encryption) to the Access Point.
?? Use
the Web Manager/Telnet of the Access Point to check whether it
is connected to the network.
?? Reconfigure
and reset the Access Point.
I cannot access the network.
?? Make
sure that the necessary driver(s) is correctly installed.
?? Make
sure that the network configuration is appropriate.
?? Make
sure that the user name or password is correct.
?? You
?? Turn
have moved out of range of the network.
off power management.
Modem Problems
The modem does not work.
?? Make
sure that the modem driver is correctly installed.
?? Make
sure that the COM port in the communication software is
correctly set.
8-10
Troubleshooting
?? Turn
off power management.
PC Card Problems
The PC card does not work.
?? Make
sure that the PC card is correctly seated.
?? If
the card requires an IRQ (Interrupt ReQuest), make sure that there
is one available.
The PC card stops communicating properly.
?? The
application may have been reset when the computer is turned off
or in Standby mode. Exit and restart the application.
Power Management Problems
The computer does not enter Standby or Hibernation mode
automatically.
?? If
you have a connection to another computer, the computer does not
enter Standby or Hibernation mode if the connection is actively in
use.
?? Make
sure that the Standby or Hibernation time-out is enabled.
The computer does not enter Standby or Hibernation mode
immediately.
?? If
the computer is performing an operation, it normally waits for the
operation to finish.
The computer does not resume from Standby or Hibernation mode.
?? The
computer automatically enters Standby or Hibernation mode
when the battery pack is empty. Do any one of the following:
? Connect the AC adapter to the computer.
? Replace the empty battery pack with a fully charged one.
Troubleshooting
8-11
The computer does not enter Hibernation mode with the Fn+F10 hot
keys.
?? Make
sure that the Hibernation function is specified for the sleep
button.
Printer Problems
The printer does not work.
?? Make
sure that the printer is turned on (if it comes with an
independent power source) and is online (ready to use).
?? Make
sure that the printer’s signal cable is properly connected.
?? Make
sure that the printer driver is correctly installed.
?? Make
sure that you have assigned the printer port correctly in your
operating system or application program.
?? Make
sure that the printer port is enabled in the SCU program.
The printer prints garbled information.
?? Make
sure that the printer driver is correctly installed.
?? Make
sure that the printer cable is properly connected.
Software Problems
An application program does not work correctly.
?? Make
sure that the software is correctly installed.
?? If
an error message appears on the screen, consult the software
program’s documentation for further information.
?? If
you are sure the operation has stop, reset the computer. (See
“Resetting the Computer” later in this chapter.)
8-12
Troubleshooting
Sound Problems
No sound is produced.
?? Make
sure that the volume control is not set too low.
?? Make
sure that the audio driver is correctly installed.
?? Make
sure that the computer is not in Standby mode.
?? If
using an external speaker, make sure that the speaker is properly
connected.
Distorted sound is produced.
?? Make
sure that the volume control is not set too high or too low. In
most cases, a high setting can cause the audio electronics to distort the
sound.
The sound system does not record.
?? Adjust
the playback or recording sound levels.
The external microphone or audio device does not work.
?? Make
sure that the microphone is connected to the proper connector
on the computer.
?? Make
sure that your computer is equipped with the driver needed.
?? Click
the speaker symbol on the taskbar and check the Windows
volume control.
?? Check
the volume control of your computer.
Startup Problems
When you turn on the computer, it does not respond and the Power
Indicator does not light green.
?? If
you are using an external AC power, make sure that the AC adapter
is correctly and securely connected. If so, make sure that the electrical
outlet works properly.
Troubleshooting
8-13
?? If
you are using the battery power, make sure that the battery is not
discharged.
When you turn on the computer, it stops after POST.
?? Restart
your computer.
The message “Operating system not found” appears on the screen
after you turn on the computer.
?? Make
sure that there is no floppy disk in the floppy disk drive. If there
is, remove it and restart the system.
?? If
this message appears when you are booting from the hard disk,
insert a bootable disk in the floppy disk drive and check the condition
of the hard disk.
?? Make
sure that the hard disk is recognized correctly in the SCU
program.
The message “Invalid system disk” or “Disk error” appears on the
screen after you turn on the computer.
?? If
you are deliberately trying to boot from a floppy disk, replace the
disk with a bootable one and press any key to continue booting.
?? If
you are booting from the hard disk, make sure that there is no
floppy disk in the floppy disk drive. If there is, remove it and restart
the system.
?? If
this message appears when you are booting from the hard disk,
insert a bootable disk in the floppy disk drive and check the condition
of the hard disk.
?? Make
sure that the hard disk is set correctly in the SCU program.
Other Problems
The date /time is incorrect.
?? Correct
8-14
the date and time via the operating system or SCU program.
Troubleshooting
?? After
you have performed everything as described above and still
have the incorrect date and time every time you turn on the computer,
the RTC (Real-Time Clock) battery is at the end of its life. Call an
authorized dealer to replace the RTC battery.
Troubleshooting
8-15
Resetting the Computer
You may have to reset (reboot) your computer on some occasions when
an error occurs and the program you are using hangs up.
If the system operation seems to hang up, first wait. It is possible that the
system is processing data. Periodically check the hard disk drive in-use
indicator, if it flashes irregularly, the program may be accessing data and
preventing you from using the keyboard. If you are sure the operation has
stopped and you cannot use the “restart” function of the operating system,
reset the computer.
Reset the computer by any one of these methods:
?? Press Ctrl+ Alt+ Del.
?? If the above action does not work, turn off the system. Wait for at least
five seconds and turn it on again.
CAUTION: Resetting will cause any unsaved data to be lost.
8-16
Troubleshooting
APPENDIX
Specifications
NOTE: Specifications are subject to change without any prior notices.
Parts
CPU
Specifications
Intel Dothan Low Voltage Processor, µ -FCBGA package, 1.4 GHz
400 MHz Front Side Bus (FSB)
Cache Memory
L2 2 MB on-die
ROM BIOS
512 KB Flash EEPROM (includes system and VGA BIOS)
RAM
System
Two 200-pin PC2100/PC2700 DDR SO-DIMM sockets,
maximum 2 GB (standard 256 MB)
Video
4/8/16/32/64 MB (shared system memory)
Display
Panel
14.1/15-inch TFT XGA LCD, resolution up to 1024×768,
Touchscreen (option),
High-contrast display (option)
Video controller
Integrated in NorthBridge, or
ATI M11 discrete VGA controller with 64 MB memory (option)
32-bit 2D/3D graphic core with Dynamic Video Memory
Technology, dual view function, LCD/CRT simultaneous display
capability
Video port
VGA port
Keyboard
Waterproof membrane cover
Waterproof rubber keyboard (option)
Rubber keyboard with backlight feature (option)
Pointing device
Touchpad with two buttons (raindrop resistant)
Storage
Hard disk drive bay Easily removable for maintenance, includes encryption eNOVA
device
feature, built-in heater for low temperature support (–20 0 C~55 0 C)
Ultra DMA 33/66/100
Optical drive bay
Easily swappable bay for slim-type CD drive, or
Combo drive, or
DVD dual recorder drive, or
Second battery
Parts
Specifications
Audio
Audio controller SIGMATEL 9750 AC97 codec Rev.2.3 support,
two built -in 2-watts stereo speakers,
SoundBlaster Pro and digital controller compatibility
Audio port
Two audio ports for Mic-in / Line-out (supports S/P-DIF)
PC card
Type II × 2 or Type III × 1, CardBus support
I/O ports
On right side
X-Bay, two USB ports (supports system boot-up from CD drive),
one PS/2 port
On rear side
IR port, serial port, RJ-11 port, RJ-45 port, parallel port
On underside
Docking port (POGO) supports hot docking
Communication LAN
10/100Base-T Ethernet
Wireless LAN
Integrated WLAN (Intel Centrino platform) with built-in antenna
Modem
56 kbps V.90 MDC
Power
AC adapter
Input: 100?240 V AC, 50?60 Hz AC auto-sensing/switching
Output: 90 W Universal or above
Battery
Li-ion battery 6000 mAH / 11.1 V, 9 cells, cylindrical-type
Dimension (W×D×H)
12.9×10.7×1.6 inch (328×272×41 mm)
Weight
Less than 9.04 lb (4.1 kg)
Environment
Temperature
Operating: 0 ?C (32 ?F) to 55 ?C (131 ?F) – standard
–20 ?C (–4 ?F) to 55 ?C (131 ?F) – option
Storage:
–20 ?C (–4 ?F) to 70 ?C (158 ?F)
Humidity
Operating: 5 % to 95 % RH, non-condensing
A-2
Specifications
APPENDIX
Regulatory Information
This appendix provides regulatory statements and safety notices on your
computer.
NOTE: Marking labels located on the exterior of your computer indicate the regulations
that your model complies with. Please check the marking labels and refer to the
corresponding statements in this appendix. Some notices apply to specific models only.
On the Use of the System
Class B Regulations
USA
Federal Communications Commission Radio Frequency Interference
Statement
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
??
Reorient or relocate the receiving antenna.
??
Increase the separation between the equipment and receiver.
??
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
??
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
Please note:
The use of a non-shielded interface cable with this equipment is
prohibited.
B-2
Regulatory Information
Canada
Canadian Department of Communications
Radio Interference Regulations Class B Compliance Notice
This Class B digital apparatus meets all requirements of the Canada
Interference-Causing equipment regulations.
Cet appareil numérique de Classe B respecte toutes les exigences du
Règlement Canadien sur le matériel brouileur.
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada.
Safety Notices
About the Battery
Caution Texts Concerning Lithium Batteries
DANISH
ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må
kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til
leverandøren.
NORWEGIAN
ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype
eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i
henhold til fabrikantens instruksjoner.
SWEDISH
VARNING: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en
ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt
fabrikantens instruktion.
FINNISH
VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo
ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden mukaisesti.
Regulatory Information
B-3
ENGLISH
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the equipment manufacturer. Discard used
batteries according to manufacturer's instructions.
DEUTSCH
VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur
durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
FRENCH
ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d’un type équivalent
recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
Attention (for USA Users)
The product that you have purchased contains a rechargeable battery. The battery is
recyclable. At the end of its useful life, under various state and local laws, it may be illegal
to dispose of this battery into the municipal waste stream. Check with your local solid
waste officials for details in your area for recycling options or proper disposal.
About the AC Adapter
B-4
??
Use only the AC adapter supplied with your computer. Use of another
type of AC adapter will result in malfunction and/or danger.
??
Do not use the adapter in a high moisture environment. Never touch
the adapter when your hands or feet are wet.
??
Allow adequate ventilation around the adapter when using it to
operate the device or charge the battery. Do not cover the AC adapter
with paper or other objects that will reduce cooling. Do not use the
AC adapter while it is inside a carrying case.
??
Connect the adapter to a proper power source. The voltage
requirements are found on the product case and/or packaging.
??
Do not use the adapter if the cord becomes damaged.
??
Do not attempt to service the unit. There are no serviceable parts
inside. Replace the unit if it is damaged or exposed to excess
moisture.
Regulatory Information
About the Modem
Caution
??
Never install telephone wiring during a lightning storm.
??
Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
??
Never touch non-insulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
??
Use caution when installing or modifying telephone lines.
??
Avoid using the telephone function (other than a cordless type) during
an electrical storm. There may be a remote risk of electric shock from
lightning.
??
Do not use the telephone function to report a gas leak in the vicinity of
the leak.
??
Do not use this product near water, for example near a bathtub, wash
bowl, kitchen sink or laundry tub, in a wet basement or near a
swimming pool.
Caution (for USA Users)
To reduce the risk of fire, use only No.26 AWG or larger
telecommunication line cord.
Regulatory Information
B-5
On the Use of RF Device
USA and Canada Safety Requirements and Notices
IMPORTANT NOTE: To comply with FCC RF exposure compliance
requirements, the antenna used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or
transmitter.
Radio Frequency Interference Requirements and SAR
The FCC with its action in ET Docket 93-62 has adopted a safety
standard for human exposure to Radio Frequency (RF) electromagnetic
energy emitted by FCC certified equipment. The wireless LAN module
meets the Human Exposure limits found in OET Bulletin 65, 2001, and
ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the
instructions found in this manual will result in exposure substantially
below the FCC’s recommended limits. The following safety precautions
should be observed:
??
Do not touch or move antenna while the unit is transmitting or
receiving.
??
Do not hold any component containing the radio such that the antenna
is very close or touching any exposed parts of the body, especially the
face or eyes, while transmitting.
??
Do not operate the radio or attempt to transmit data unless the antenna
is connected; if not, the radio may be damaged.
Use in specific environments:
B-6
??
The use of wireless devices in hazardous locations is limited by the
constraints posed by the safety directors of such environments.
??
The use of wireless devices on airplanes is governed by the Federal
Aviation Administration (FAA).
Regulatory Information
??
The use of wireless devices in hospitals is restricted to the limits set
forth by each hospital.
Antenna use:
??
In order to comply with FCC RF exposure limits, low gain integrated
antenna has be installed in the top of LCD panel to keep a minimum
distance of 20 cm (8 inches) or more from the body of all persons
during all normal usage conditions.
Explosive Device Proximity Warning
WARNING: Do not operate a portable transmitter (such as a wireless
network device) near unshielded blasting caps or in an explosive
environment unless the device has been modified to be qualified for such
use.
Antenna Warning
WARNING: To comply with the FCC and ANSI C95.1 RF exposure
limits, it is recommended that the antenna for this device be installed so
as to provide a separation distance of at least 20 cm (8 inches) from all
persons and that the antenna must not be co-located or operating in
conjunction with any other antenna or radio transmitter. It is
recommended that the user limit exposure time if the antenna is
positioned closer than 20 cm (8 inches).
Use on Aircraft Caution
CAUTION: Regulations of the FCC and FAA prohibit airborne
operation of radio-frequency wireless devices because their signals could
interfere with critical aircraft instruments.
Regulatory Information
B-7
EMC Requirements
This device uses, generates and radiates radio frequency energy. The radio
frequency energy produced by this device is well below the maximum
exposure allowed by the Federal Communications Commission (FCC).
This device complies with the limits for a Class B digital device pursuant
to Part 15 subpart C of the FCC Rules and Regulations. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
The FCC limits are designed to provide reasonable protection against
harmful interference when the equipment is installed and used in
accordance with the instruction manual and operated in a commercial
environment. However, there is no guarantee that interference will not
occur in a particular commercial installation, or if operated in a residential
area.
If harmful interference with radio or television reception occurs when the
device is turned on, the user must correct the situation at the user’s own
expense. The user is encouraged to try one or more of the following
corrective measures:
??
Reorient or relocate the receiving antenna.
??
Increase the separation between the equipment and receiver.
??
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
??
Consult the dealer or an experienced radio/TV technician for he lp.
CAUTION: The Part 15 radio device operates on a non-interference
basis with other devices operating at this frequency. Any changes or
modification to said product not expressly approved by the manufacturer
could void the user’s authority to operate this device.
B-8
Regulatory Information
Canada Radio Frequency Interference Requirements
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and away from windows to provide
maximum shielding. Equipment (or its transmit antenna) that is installed
outdoors is subject to licensing.
Pour empêcher que cet appareil cause du brouillage au service faisant
l'objet d'une licence, il doit être utilisé à l'intérieur et devrait être placé
loin des fenêtres afin de fournir un écran de blindage maximal. Si le
matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire
l'objet d'une licence.
European Union CE Marking and Compliance Notices
Statements of Compliance
English
This product follows the provisions of the European Directive
1999/5/EC.
Danish
Dette produkt er i overensstemmelse med det europæiske direktiv
1999/5/EC.
Dutch
Dit product is in navolging van de bepalingen van Europees Directief
1999/5/EC.
Finnish
Tämä tuote noudattaa EU-direktiivin 1999/5/EC määräyksiä.
French
Ce produit est conforme aux exigences de la Directive Européenne
1999/5/EC.
German
Dieses Produkt entspricht den Bestimmungen der Europäischen
Richtlinie 1999/5/EC.
Regulatory Information
B-9
Greek
To p????? a?t? p????? t?? p??ß???e?? t?? ????pa???? ? d???a?
1999/5/EC.
Icelandic
Þessi vara stenst reglugerð Evrópska Efnahags Bandalagsins númer
1999/5/EC.
Italian
Questo prodotto è conforme alla Direttiva Europea 1999/5/EC.
Norwegian
Dette produktet er i henhold til bestemmelsene i det europeiske direktivet
1999/5/EC.
Portuguese
Este produto cumpre com as normas da Diretiva Européia 1999/5/EC.
Spanish
Este producto cumple con las normas del Directivo Europeo 1999/5/EC.
Swedish
Denna produkt har tillverkats i enlighet med EG-direktiv 1999/5/EC.
Local Restrictions of 802.11b/802.11g Radio Usage
CAUTION: Due to the fact that the frequencies used by 802.11b/
802.11g wireless LAN devices may not yet be harmonized in all
countries, 802.11b/802.11g products are designed for use only in specific
countries or regions, and is not allowed to be operated in countries or
regions other than those of designated use. As a user of these products,
you are responsible for ensuring that the products are used only in the
countries or regions for which they were intended and for verifying that
they are configured with the correct selection of frequency and channel
for the country or region of use. Any deviation from permissible settings
and restrictions in the country or region of use could be an infringement
of local law and may be punished as such.
The European variant is intended for use throughout the European
Economic Area. However, authorization for use is further restricted in
particular countries or regions within countries, as follows:
B-10
Regulatory Information
General
European standards dictate maximum radiated transmit power of 100
mW Effective Isotropic Radiated Power (EIRP) and the frequency range
2400 – 2483.5 MHz.
Belgium and the Netherlands
In Belgium and the Netherlands, the product may not be used outdoors.
See the instructions next under the heading “How to Turn Off the
Wireless LAN Radio.”
France
Departments in Which the Wireless LAN Module Can Be Used
(Indoors Only)
The wireless LAN module can currently be used indoors only in the
following 38 departments of mainland France. Please turn off your
wireless LAN radio when operating the device in areas/places other than
the 38 departments listed:
01
Ain Orientales
36
Indre
66
Pyrénées
02
Aisne
37
Indre et Loire
67
Bas Rhin
03
Allier
41
Loir et Cher
68
Haut Rhin
05
Hautes Alpes
42
Loire
70
Haute Saône
08
Ardennes
45
Loiret
71
Saône et Loire
09
Ariège
50
Manche
75
Paris
11
Aude
55
Meuse
82
Tarn et Garonne
12
Aveyron
58
Nièvre
84
Vaucluse
16
Charente
59
Nord
88
Vosges
24
Dordogne
60
Oise
89
Yonne
25
Doubs
61
Orne
90
Territoire de Belfort
26
Drôme
63
Puy du Dôme
94
Val de Marne
32
Gers
64
Pyrénées Atlantique
Regulatory Information
B-11
Departments in Which the Wireless LAN Module’s Maximum EIRP
Not Shown in the Previous Table
Frequency Ranges (MHz)
Indoors
Outdoors
2400 – 2446.5
10 mW
Not permitted
2446.5 – 2483.5
100 mW
100 mW on private property with
Ministry of Defense approval
Turning Off the Wireless LAN Radio
NOTE: Turning the wireless LAN radio off is not the same as disabling
the wireless LAN card. It is not necessary to disable the card to meet the
regulatory requirements.
While operating the computer in those French departments that do not
allow use of the wireless LAN equipment, the user of the equipment must
turn off the wireless LAN radio in order to comply with local regulations.
B-12
Regulatory Information

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : M220-0A - Microsoft Word
Create Date                     : 2005:01:26 10:46:41
Title                           : M220-0A.PDF
Author                          : 8112009
Producer                        : Acrobat PDFWriter 4.0 for Windows NT
Modify Date                     : 2005:01:26 11:12:44+08:00
Page Count                      : 136

EXIF Metadata provided by EXIF.tools

Getac Technology 012 Notebook with WLAN User Manual M220 0A

Getac Technology Corp. Notebook with WLAN M220 0A

Manual

FCC ID Filing: MAU012

Navigation menu

Namespaces

Views

Navigation