Getac Technology EMPT116F Digitizer module User Manual OEM PRODUCT SPECIFICATION

Download:
Mirror Download [FCC.gov]
Document ID	3517770
Application ID	DAQCZPY+efcYbyM3hMb7yw==
Document Description	User Manual Module
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.7kB (583783 bits)
Date Submitted	2017-08-18 00:00:00
Date Available	2018-02-17 00:00:00
Creation Date	2017-08-09 13:22:14
Producing Software	Microsoft® Word 2010
Document Lastmod	2017-08-15 17:01:33
Document Title	OEM PRODUCT SPECIFICATION
Document Creator	Microsoft® Word 2010
Document Author:	rhett 陳文政

EMPEN T116 Sensor SPECIFICATION
Product Name:TF1-DIGITIZER;ASIC,11.6”,F110G4,EMP
Getac P/N: 412888700007
EMPEN P/N : 20160002
Firmware Version : 18
Revision History
Revision
Date
Description
Author /Revised by
01
2016/11/29
Initial
Jesse
1. Product Specifications
1.1 General Specifications

Technology
Battery free Electro-magnetic
Interface
USB
VID & PID
VID:0x0458, PID:0x501D
Active Area
258.13×146mm
Resolution
0.01mm / 2560 LPI (see Note 5)
Coordinate Accuracy
±0.4mm (see Note 1, 2, 3 and 5)
Coordinate Jitters
1-point max (see Note 1 and 5)
Detectable Pen tilt
Up to 50° from vertical (see Note 5)
Detectable Height
4 to 14mm above the Sensor Film (see Note 1 and 5)
Position Report Rate
133 PPS ( Pen hover at sensor center )
Pressure Resolution
1024 levels (see Note 4 and 5)
EM module Thickness
3.0 mm max
Note 1: The EM Sensor Board and Stylus at ordinary temperature.
Note 2: The pen held vertically at 0mm high from sensor film.
Note 3: See Picture1, the accuracy guaranteed region is 15mm or more inside region
from the active area edge.
Note 4: Pressure range is 20g≦200 levels and 650g≦1023 levels
Note 5: This function must be used with Getac TF1-DIGITIZER PEN unit
Picture1
1.2 Dimensional Outline of PCBA and Sensor Film
1.3 Electrical Specifications
1.3.1 Circuit Diagram
TLSC3590ET88
Controller Board
Signal Assignment
Sensor Film
Pin
Name
Function
NC
Not Connect
USB-
USB- Signal
USB+
USB+ Signal
NC
Not Connect
NC
Not Connect
NC
Not Connect
VCC +5V
Power Supply
GND
Ground
1.3.2 Test Conditions

Ambient Temperature : 25+/- 5 ℃

Ambient Humidity : 65 +/- 16% ( RH)

Supply Voltage : VDD 5V
Item
Min.
Typ.
Max.
Unit.
4.75
5.0
5.25
75
80
98
mA
Current Consumption
Pen@10cm
85
90
100
mA
Current Consumption
Standby mode
84
110
124
mA
Supply Voltage
Current Consumption
Pen in touch
Low Scan mode
16
(400mSec)
35
125
(130mSec)
mA
Remark
Keep standby
mode 40 min
will entry low
scan mode
2. Reliability Test
Item
Humidity Test
SPEC
Testing method
30℃/95%~61℃/95%,
1. All functions must be
12 hours for 30℃/95%, MIL-STD-810G- 507.5
normally
12 hours for 61℃/95%, Humidity Procedure – II 2. No oxidation on
one cycle is 24 hours ,
Aggravated
test time is 10days
High Temperature Test
(Operating)
High Temperature Test
(Non-Operating)
Criteria
61℃ 96h
3. No visual abnormal.
MIL-STD-810G-501.5
4. There shall not be any
Procedure II Operation
cosmetic damage
5. T/S cannot allow the
12 hours for 31℃,
abnormal status like
one cycle is 24 hours,
screws.
33℃~71℃ ,10days
12 hours for 71℃
Number
of test
samples
MIL-STD-810G-501.5
Procedure I
peel off, bubble .
test time is 10days
Low Temperature Test
(Operating)
Low Temperature Test
(Non-Operating)
Drop Test
Temperature Shock Test
-21℃ 96h
-40℃ 96h
MIL-STD-810G-502.5
Procedure II
MIL-STD-810G-502.5
Procedure I
1h, 3cycle ,total:6h
120cm Wood floors
-41℃~71℃ duration
MIL-STD-810G-503.5
Procedure-I-C
Multi-cycle shock.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : rhett 陳文政
Create Date                     : 2017:08:09 13:22:14+08:00
Modify Date                     : 2017:08:15 17:01:33+08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Metadata Date                   : 2017:08:15 17:01:33+08:00
Creator Tool                    : Microsoft® Word 2010
Format                          : application/pdf
Title                           : OEM PRODUCT SPECIFICATION
Creator                         : rhett 陳文政
Document ID                     : uuid:a1c0517d-82f9-498f-b59a-03a61a00ab8d
Instance ID                     : uuid:b2af937d-f551-4411-83e2-e3e9e8b78f72
Producer                        : Microsoft® Word 2010
Page Count                      : 6

EXIF Metadata provided by EXIF.tools