Getac Technology ZX70U UHF RFID reader User Manual Statement

Getac Technology Corporation UHF RFID reader Statement

Contents

User Manual Statement

Download: Getac Technology ZX70U UHF RFID reader User Manual Statement
Mirror Download [FCC.gov]Getac Technology ZX70U UHF RFID reader User Manual Statement
Document ID3546818
Application IDSByycmOLQgC9qrtBfMXVSg==
Document DescriptionUser Manual Statement
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeYes
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize41.65kB (520673 bits)
Date Submitted2017-09-06 00:00:00
Date Available2018-03-07 00:00:00
Creation Date2017-08-24 13:14:33
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2017-09-04 17:34:13
Document TitleUser Manual Statement
Document CreatorMicrosoft® Office Word 2007

Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:


Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:
 Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
 This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This module can be used with Product name: ZX70 or similar platform with similar dimension, antenna
location and RF characteristic.
This device is intended only for OEM integrators under the following conditions:
1)
2)
The transmitter module may not be co-located with any other transmitter or
antenna. The co-transmitting with other radio will need a separate evaluation.
Module approval valid only when this module is installed in the tested host
“ZX70”.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions cannot be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID cannot be used on the
final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains
FCC ID: QYLZX70U”. The grantee's FCC ID can be used only when all FCC
compliance requirements are met.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2017:08:24 13:14:33+08:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2017:09:04 17:34:13+08:00
Metadata Date                   : 2017:09:04 17:34:13+08:00
Producer                        : Microsoft® Office Word 2007
Format                          : application/pdf
Document ID                     : uuid:e9b47d4d-7cf0-42d2-93f8-db77c1926d82
Instance ID                     : uuid:ad922c28-496f-452e-acf3-64503139c9bf
Page Count                      : 2
Language                        : zh-TW
Creator                         : Microsoft® Office Word 2007
EXIF Metadata provided by EXIF.tools
FCC ID Filing: QYLZX70U

Navigation menu