Gibson Innovations BT7900 EverPlay Wireless Portable Speaker User Manual

Gibson Innovations Limited EverPlay Wireless Portable Speaker

User Manual

Register your product and get support atwww.philips.com/supportUser manualBT7900
1ENContents1 Important 1Safety 1Notice 12 Your Bluetooth speaker 3Introduction 3What's in the box 3Overview of the speaker 43 Get started 4Turn on/o 4Check the battery level 5Charge the built-in battery 54 Play from Bluetooth devices 7Connect a Bluetooth device 7Play from a connected Bluetooth device 7Disconnect a device 8Reconnect a device 8Clear pairing information 8Control your phone call 85 Other features 9Listen to an external device 9Adjust volume 9Attach the lanyard cable 96 Speci cations 107 Trouble shooting 11General 11About Bluetooth device 11
1EN1 ImportantSafety Warning •Never remove the casing of this speaker. •Never place this speaker on other electrical equipment. •Keep this speaker away from direct sunlight, naked ames or heat.• Only use attachments or accessories specied by the manufacturer.• The battery shall not be exposed to excessive heat such as sunshine, re or the like.• Do not place any sources of danger on the speaker (e.g. lighted candles). • The speaker can meet IP57 waterproof standard only when the USB/AUDIO IN socket cover is covered seamlessly.• If your speaker gets wet, clean with a soft dry cloth and then let it dry completely in a well-ventilated place before use next time.• The operation temperature of the product is from -10 °C to 40 °C.• For safety reasons, the battery will not be charged if the battery temperature is below 0 °C or above 40 °C.Note• The type plate is located on the left side of the speaker.NoticeAny changes or modications made to this device that are not expressly approved by Gibson Innovations may void the user’s authority to operate the equipment.Notice of compliance (for the USA and Canada)The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and2 This device must accept any interference received, including interference that may cause undesired operation.FCC rulesThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Relocate the receiving antenna.
2EN• Increase the separation between equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.CanadaThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following Two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.CAN ICES-3(B)/NMB-3(B)IC Radiation Exposure StatementThis equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Caution: The user is cautioned that changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Care of the environmentDisposal of your old product and battery Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com.This product contains non-removable batteries:• Do not incinerate. Batteries may explode if overheated.• For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com.Caution •Removal of the built-in battery invalidates the warranty and may destroy the product.Always bring your product to a professional to remove the built-in battery.Environmental informationAll unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations
3ENregarding the disposal of packaging materials, exhausted batteries and old equipment.Trademark notice The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Gibson Innovations Limited is under license. Other trademarks and trade names are those of their respective owners.Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.Quick Charge is a trademark of Qualcomm Incorporated. All Qualcomm Incorporated trademarks are used with permission.2 Your Bluetooth speakerCongratulations on your purchase, and welcome to Philips! To fully benet from the support that Philips oers, register your product at www.philips.com/welcome.IntroductionWith this speaker, you can enjoy audio from Bluetooth-enabled devices or other external audio devices through a 3.5mm audio-in cable.What's in the boxCheck and identify the contents of your package: Quick Start GuideBT7900 Portable speakerRegister your product and get support at www.philips.com/support• Speaker• USB lanyard cable • Printed materials
4ENOverview of the speakera -/+• Adjust volume.b Battery level indicators• Show the charging progress.• Show the battery level.c • Enter Bluetooth pairing mode.• Clear Bluetooth pairing information.d • Turn the speaker on or o.• Check the battery level.• Show the Bluetooth status.e • In Bluetooth mode, press to pause or resume play.• In Bluetooth mode, press twice to play the next track.• Respond to an incoming call through Bluetooth connection.f AUDIO IN• Connect an external audio device. g • Charge the built-in battery.3 Get startedAlways follow the instructions in this chapter in sequence.Turn on/o • To turn the speaker on, press and hold for over two seconds. » The Bluetooth indicator starts ashing. » The battery level indicators light up briey. » The speaker beeps.• To turn the speaker o, press and hold for two seconds again.Note •When there is no Bluetooth connection for 15 minutes or the battery is at low level, the speaker turns o automatically to save power. •When there is neither audio playback nor user operation for 5 minutes, the current Bluetooth connection is disconnected, the Bluetooth indicators is dimmed, and the speaker enters standby mode automatically.
5ENCheck the battery levelThe speaker is powered by the built-in rechargeable battery. After power-on, the speaker shows the battery level immediately, and the battery indication disappears in ve seconds.• To manually check the battery level, briey press in either power-on or power-o mode. » The dierent behavior of the four LEDs indicates dierent battery levels.LED indication: Battery powerLED 1 LED 2 LED 3 LED 4Full Solid white> 8% Solid white O50% - 80% Solid white O20% - 50%Solid white OLow battery (<20%)Flash red OLED 1LED 3LED 4LED 2Charge the built-in batteryNote •It takes you approximately three hours to fully charge the battery. •The micro USB socket is for charging only. •Rechargeable battery has a limited number of charge cycles. Battery life and number of charge cycles vary by use and settings. •You can use a power adaptor compatible with Quick Charge 3.0 (not supplied; 5V 2.1A output recommended) to speed up the charging process.When the battery level is low, LED 1 ashes red as illustrated. To charge the built-in battery:• Pull out the USB cable from the USB lanyard cable as illustrated.
6EN• Connect the speaker to AC power by using a power adaptor (not supplied; 5V 2.1 A adaptor recommended). System statusBattery statusSystem behaviorOn Under chargingBeep once, without charging indication. O Under chargingShow the charging indication O Fully chargedAll LEDs are on, then turn o after three minutes.Check the charging progressDuring charging, you can press to check the charging progress. Battery levelLED 1 LED 2 LED 3 LED 4<20% chargedFlash white O20% - 50% chargedSolid whiteFlash white OBattery levelLED 1 LED 2 LED 3 LED 450% - 80% chargedSolid white Flash white O> 80% charged Solid white Flash whiteFully chargedSolid white (turn o in 3 minutes)
7EN4 Play from Bluetooth devicesWith this speaker, you can listen to audio from Bluetooth-enabled devices and control the incoming call through Bluetooth.Connect a Bluetooth deviceNote •Make sure that Bluetooth function is enabled on your device, and your device is set as visible to all other Bluetooth devices. •Any obstacle between this speaker and a Bluetooth device can reduce the operational range. •Keep away from any other electronic device that may cause interference. •The operational range between this speaker and a Bluetooth device is approximately 30 meters.1 Make sure that the speaker is in Bluetooth pairing mode. » The Bluetooth LED ashes blue quickly. » If the LED ashes blue slowly, press and hold for two seconds to enter pairing mode.2 On your Bluetooth device, enable Bluetooth and search for Bluetooth devices that can be paired (see the user manual of the device).3 Select [Philips BT7900] displayed on your device for pairing. If necessary, input “0000” as the pairing password. » After successful connection, the speaker beeps twice, and the LED turns solid blue. LED behavior DescriptionFlashing blue quickly Ready for pairing Flashing blue slowlyReconnecting the last connected device;Waiting for connection from the paired deviceSolid blue ConnectedPlay from a connected Bluetooth deviceNote •Music play pauses when there is an incoming call, and resumes when your phone call ends.
8ENAfter successful Bluetooth connection, play audio on the connected device. » Audio streams from your Bluetooth device to the speaker.• To pause or resume play, press .• To play the next track, press twice.Tip •You can also use your Bluetooth device to control play.Disconnect a device• Press and hold for two seconds; • Turn o the speaker;• Disable Bluetooth on your device; or• Move the device beyond the communication range. Reconnect a device• When you turn on the speaker, it tries to reconnect the last connected device automatically; • If not successful, select [Philips BT7900] on your Bluetooth menu to start reconnection.Clear pairing information • Press and hold for 10 seconds.Control your phone callAfter Bluetooth connection, you can control an incoming call with this speaker. Button FunctionPress to answer an incoming call.Press and hold for two seconds to reject an incoming call.During a call, press to end the current call.During a call, press and hold for two seconds to transfer the call to your mobile device.
9EN5 Other featuresListen to an external deviceWith this speaker, you can also listen to an external audio device such as an MP3 player.Note •Make sure that music playback through Bluetooth is stopped.1 Connect an audio input cable (not supplied) with a 3.5 mm connector on both ends to• the AUDIO IN socket on this speaker, and• the headphone socket on the external device.2 Play audio on the external device (refer to its user manual).Tip •When you start music streaming from a connected Bluetooth device, the speaker switches to the Bluetooth source automatically.Adjust volumeDuring music playback, press -/+ to increase or decrease volume. Tip •You can press and hold -/+ to increase or decrease volume continuously. •When the volume reaches the maximum, the speaker beeps twice. Attach the lanyard cableFor easy carrying, attach the supplied USB lanyard cable to this speaker as illustrated.EN
10Dimensions - Main unit (W x H x D)201 x 71 x 72 mmWeight - Main unit 0.53 kg6 Specif icationsNote •Product information is subject to change without prior notice.Rated output power (Amplier)2 x 7W RMS ≤ 1% THDAcoustic frequency response65-20000 HzSpeaker driver 2 x 1.5” full range, 4 ΩBass enhancement 2 x 2.25” passive radiatorBluetooth versionV2.1 + EDRBluetooth supported prolesAVRCP V1.4, A2DP V1.2, HFP V1.5Bluetooth frequency band / Output power2.402GHz ~ 2.480GHz ISM Band / ≤ 4dBm (Class 2) AUX input level 500mV±100mVDurability IP57Built-in battery Li-ion battery (3.6 V, 4000 mAh)Play time in battery modeApprox. 10 hours Charging time Approx. 3 hours with 5V 2.1A power adaptorApprox. 1.5 hours with Quick Charge power adaptor USB charging 5V, 2.1A / Micro-USB socket / supporting Quick Charge 3.0EN
11About Bluetooth deviceThe audio quality is poor after connection with a Bluetooth-enabled device. •The Bluetooth reception is poor. Move the device closer to this product or remove any obstacle between them.Fail to nd [Philips BT7900] on your device for pairing. •Press and hold for two seconds to enter pairing mode, and then try again. Cannot connect with the device. •The Bluetooth function of the device is not enabled. Refer to the user manual of the device for how to enable the function. •This product is already connected with another Bluetooth-enabled device. Disconnect that device and then try again.The paired device connects and disconnects constantly. •The Bluetooth reception is poor. Move the device closer to this product or remove any obstacle between them. •For some devices, Bluetooth connection may be deactivated automatically as a power-saving feature. This does not indicate any malfunction of this product.7 Trouble-shootingWarning •Never remove the casing of this device.To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www.philips.com/support). When you contact Philips, make sure that the device is nearby and the model number and serial number are available.GeneralNo power •Recharge the speaker.No sound •Adjust volume on this product. •Adjust volume on the connected device. •In AUDIO IN mode, make sure that music playback through Bluetooth is stopped. •Make sure that your Bluetooth device is within the eective operational range.No response from the speaker when pressing any key. •The speaker is in demo mode. To exit this mode: press and hold for 20 seconds. EN
2017 © Gibson Innovations Limited. All rights reserved.This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product.Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.BT7900_37_UM_V1.0

Navigation menu