Gibson Innovations BT7900 EverPlay Wireless Portable Speaker User Manual
Gibson Innovations Limited EverPlay Wireless Portable Speaker
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3298271 |
| Application ID | 4kPwTVqCUG/adHgOffDqjw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 164.73kB (2059145 bits) |
| Date Submitted | 2017-02-28 00:00:00 |
| Date Available | 2017-02-28 00:00:00 |
| Creation Date | 2017-02-16 15:06:46 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2017-02-16 15:07:04 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CC 2017 (Windows) |
User manual BT7900 Register your product and get support at www.philips.com/support Contents Important Safety Notice 2 Your Bluetooth speaker Introduction What's in the box Overview of the speaker 3 Get started Turn on/off Check the battery level Charge the built-in battery 4 Play from Bluetooth devices Connect a Bluetooth device Play from a connected Bluetooth device Disconnect a device Reconnect a device Clear pairing information Control your phone call 5 Other features Listen to an external device Adjust volume Attach the lanyard cable 6 Specifications 7 Troubleshooting General About Bluetooth device 10 11 11 11 EN 1 Important Safety Warning •• Never remove the casing of this speaker. •• Never place this speaker on other electrical equipment. •• Keep this speaker away from direct sunlight, naked flames or heat. • Only use attachments or accessories specified by the manufacturer. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. Do not place any sources of danger on the speaker (e.g. lighted candles). The speaker can meet IP57 waterproof standard only when the USB/AUDIO IN socket cover is covered seamlessly. If your speaker gets wet, clean with a soft dry cloth and then let it dry completely in a well-ventilated place before use next time. The operation temperature of the product is from -10 °C to 40 °C. For safety reasons, the battery will not be charged if the battery temperature is below 0 °C or above 40 °C. • • • • • • Note • The type plate is located on the left side of the speaker. EN Notice Any changes or modifications made to this device that are not expressly approved by Gibson Innovations may void the user’s authority to operate the equipment. Notice of compliance (for the USA and Canada) The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. FCC rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Relocate the receiving antenna. • • • Increase the separation between equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following Two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3(B)/NMB-3(B) IC Radiation Exposure Statement This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Care of the environment Disposal of your old product and battery Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or visit www.recycle.philips.com. This product contains non-removable batteries: • Do not incinerate. Batteries may explode if overheated. • For disposal or recycling information, please contact your local authorities or visit www. recycle.philips.com. Caution •• Removal of the built-in battery invalidates the warranty and may destroy the product. Always bring your product to a professional to remove the built-in battery. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations EN regarding the disposal of packaging materials, exhausted batteries and old equipment. Trademark notice The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Gibson Innovations Limited is under license. Other trademarks and trade names are those of their respective owners. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. Quick Charge is a trademark of Qualcomm Incorporated. All Qualcomm Incorporated trademarks are used with permission. 2 Your Bluetooth speaker Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/ welcome. Introduction With this speaker, you can enjoy audio from Bluetooth-enabled devices or other external audio devices through a 3.5mm audio-in cable. What's in the box Check and identify the contents of your package: Portable speaker Quick Start Guide BT7900 Register your product and get support at www.philips.com/support • • • EN Speaker USB lanyard cable Printed materials Overview of the speaker 3 Get started Always follow the instructions in this chapter in sequence. Turn on/off a -/+ • Adjust volume. • b Battery level indicators • Show the charging progress. • Show the battery level. • • Enter Bluetooth pairing mode. Clear Bluetooth pairing information. • • • Turn the speaker on or off. Check the battery level. Show the Bluetooth status. • In Bluetooth mode, press to pause or resume play. In Bluetooth mode, press twice to play the next track. Respond to an incoming call through Bluetooth connection. • • To turn the speaker on, press and hold for over two seconds. »» The Bluetooth indicator starts flashing. »» The battery level indicators light up briefly. »» The speaker beeps. • To turn the speaker off, press and hold for two seconds again. Note •• When there is no Bluetooth connection for 15 minutes or the battery is at low level, the speaker turns off automatically to save power. •• When there is neither audio playback nor user operation for 5 minutes, the current Bluetooth connection is disconnected, the Bluetooth indicators is dimmed, and the speaker enters standby mode automatically. f AUDIO IN • Connect an external audio device. • Charge the built-in battery. EN Check the battery level The speaker is powered by the built-in rechargeable battery. After power-on, the speaker shows the battery level immediately, and the battery indication disappears in five seconds. • To manually check the battery level, briefly press in either power-on or power-off mode. »» The different behavior of the four LEDs indicates different battery levels. LED indication: Charge the built-in battery Note •• It takes you approximately three hours to fully charge the battery. •• The micro USB socket is for charging only. •• Rechargeable battery has a limited number of charge cycles. Battery life and number of charge cycles vary by use and settings. •• You can use a power adaptor compatible with Quick Charge 3.0 (not supplied; 5V 2.1A output recommended) to speed up the charging process. When the battery level is low, LED 1 flashes red as illustrated. LED 4 LED 3 LED 2 LED 1 Battery power Full > 80% 50% 80% 20% 50% Low battery (<20%) EN LED 1 LED 2 LED 3 LED 4 Solid white Solid white Solid white Solid white Off Flash red Off Off Off To charge the built-in battery: • Pull out the USB cable from the USB lanyard cable as illustrated. • Connect the speaker to AC power by using a power adaptor (not supplied; 5V 2.1 A adaptor recommended). System Battery status status System behavior On Under charging Beep once, without charging indication. Off Under charging Show the charging indication Off Fully charged All LEDs are on, then turn off after three minutes. Battery level 50% - 80% charged > 80% charged Fully charged LED 1 LED 2 LED 3 LED 4 Solid white Flash Off white Solid white Flash white Solid white (turn off in 3 minutes) Check the charging progress During charging, you can press check the charging progress. Battery level <20% charged 20% - 50% charged to LED 1 LED 2 LED 3 LED 4 Flash Off white Solid Flash Off white white EN 4 Play from Bluetooth devices With this speaker, you can listen to audio from Bluetooth-enabled devices and control the incoming call through Bluetooth. On your Bluetooth device, enable Bluetooth and search for Bluetooth devices that can be paired (see the user manual of the device). Select [Philips BT7900] displayed on your device for pairing. If necessary, input “0000” as the pairing password. »» After successful connection, the speaker beeps twice, and the LED turns solid blue. Connect a Bluetooth device Note •• Make sure that Bluetooth function is enabled on your device, and your device is set as visible to all other Bluetooth devices. •• Any obstacle between this speaker and a Bluetooth device can reduce the operational range. •• Keep away from any other electronic device that may cause interference. •• The operational range between this speaker and a Bluetooth device is approximately 30 meters. Make sure that the speaker is in Bluetooth pairing mode. »» The Bluetooth LED flashes blue quickly. LED behavior Description Flashing blue quickly Ready for pairing Flashing blue slowly Reconnecting the last connected device; Waiting for connection from the paired device Solid blue Connected Play from a connected Bluetooth device Note •• Music play pauses when there is an »» If the LED flashes blue slowly, press and hold for two seconds to enter pairing mode. EN incoming call, and resumes when your phone call ends. After successful Bluetooth connection, play audio on the connected device. »» Audio streams from your Bluetooth device to the speaker. • • To pause or resume play, press To play the next track, press twice. Tip •• You can also use your Bluetooth device to control play. Control your phone call After Bluetooth connection, you can control an incoming call with this speaker. Button Function Press to answer an incoming call. Press and hold for two seconds to reject an incoming call. During a call, press to end the current call. Disconnect a device • • • • Press and hold for two seconds; Turn off the speaker; Disable Bluetooth on your device; or Move the device beyond the communication range. During a call, press and hold for two seconds to transfer the call to your mobile device. Reconnect a device • • When you turn on the speaker, it tries to reconnect the last connected device automatically; If not successful, select [Philips BT7900] on your Bluetooth menu to start reconnection. Clear pairing information • Press and hold for 10 seconds. EN 5 Other features Listen to an external device With this speaker, you can also listen to an external audio device such as an MP3 player. Adjust volume During music playback, press -/+ to increase or decrease volume. Tip •• You can press and hold -/+ to increase or decrease volume continuously. •• When the volume reaches the maximum, the speaker beeps twice. Note •• Make sure that music playback through Bluetooth is stopped. Attach the lanyard cable For easy carrying, attach the supplied USB lanyard cable to this speaker as illustrated. Connect an audio input cable (not supplied) with a 3.5 mm connector on both ends to • the AUDIO IN socket on this speaker, and • the headphone socket on the external device. Play audio on the external device (refer to its user manual). Tip •• When you start music streaming from a connected Bluetooth device, the speaker switches to the Bluetooth source automatically. EN 6 Specifications Note •• Product information is subject to change Dimensions - Main unit (W x H x D) Weight - Main unit 201 x 71 x 72 mm 0.53 kg without prior notice. Rated output power (Amplifier) 2 x 7W RMS ≤ 1% THD Acoustic frequency response 65-20000 Hz Speaker driver 2 x 1.5” full range, 4 Ω Bass enhancement 2 x 2.25” passive radiator Bluetooth version V2.1 + EDR Bluetooth supported profiles AVRCP V1.4, A2DP V1.2, HFP V1.5 Bluetooth frequency band / Output power 2.402GHz ~ 2.480GHz ISM Band / ≤ 4dBm (Class 2) AUX input level 500mV±100mV Durability IP57 Built-in battery Li-ion battery (3.6 V, 4000 mAh) Play time in battery mode Approx. 10 hours Charging time Approx. 3 hours with 5V 2.1A power adaptor Approx. 1.5 hours with Quick Charge power adaptor USB charging 5V, 2.1A / Micro-USB socket / supporting Quick Charge 3.0 EN 10 7 Trouble shooting Warning •• Never remove the casing of this device. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www.philips.com/support). When you contact Philips, make sure that the device is nearby and the model number and serial number are available. General No power •• Recharge the speaker. No sound •• Adjust volume on this product. •• Adjust volume on the connected device. •• In AUDIO IN mode, make sure that music playback through Bluetooth is stopped. •• Make sure that your Bluetooth device is within the effective operational range. No response from the speaker when pressing any key. •• The speaker is in demo mode. To exit this mode: press and hold for 20 seconds. 11 EN About Bluetooth device The audio quality is poor after connection with a Bluetooth-enabled device. •• The Bluetooth reception is poor. Move the device closer to this product or remove any obstacle between them. Fail to find [Philips BT7900] on your device for pairing. •• Press and hold for two seconds to enter pairing mode, and then try again. Cannot connect with the device. •• The Bluetooth function of the device is not enabled. Refer to the user manual of the device for how to enable the function. •• This product is already connected with another Bluetooth-enabled device. Disconnect that device and then try again. The paired device connects and disconnects constantly. •• The Bluetooth reception is poor. Move the device closer to this product or remove any obstacle between them. •• For some devices, Bluetooth connection may be deactivated automatically as a power-saving feature. This does not indicate any malfunction of this product. 2017 © Gibson Innovations Limited. All rights reserved. This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. BT7900_37_UM_V1.0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Language : zh-CN XMP Toolkit : Adobe XMP Core 5.6-c137 79.159768, 2016/08/11-13:24:42 Metadata Date : 2017:02:16 15:07:04+08:00 Modify Date : 2017:02:16 15:07:04+08:00 Creator Tool : Adobe InDesign CC 2017 (Windows) Instance ID : uuid:61f269f6-21c7-40db-bf30-742cb76db529 Original Document ID : xmp.did:540CC0123072E011A125E833CCB2A077 Document ID : xmp.id:c73e5d72-3dab-ba47-9195-44da26812750 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:ca4a46ed-b3fd-0a43-a4ef-c9b745faaaa7 Derived From Document ID : xmp.did:1bb09806-ad65-6446-ad25-4e21b173bb9c Derived From Original Document ID: xmp.did:540CC0123072E011A125E833CCB2A077 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2017 (Windows) History Changed : / History When : 2017:02:16 15:06:46+08:00 Phsprop 2 : 1000 series Date Created : 2007:03:01 City : Groningen Create Date : 2005:12:01 12:32:37Z Ww numpages : 18 Ww pagecnt Cover Outside : 1 Ww pagecnt Cover Inside : 1 Ww pagecnt Content : 14 Ww pagecnt Back Inside : 1 Ww pagecnt Back Outside : 1 Ww pagecnt lang : EN:14; Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 16 Creator : Adobe InDesign CC 2017 (Windows)EXIF Metadata provided by EXIF.tools