Globaltronics gmbH and Co KG GT9000 GT-9000 User Manual Manual

Globaltronics gmbH & Co KG GT-9000 Manual

Manual

Remote Control SocketModel: GT-FSI-07-US + GT-9000Please read theentire instruction manual before using theproduct and then save it for future reference. We reserve theright for any errors in text or images and any necessary changes made to technicaldata.If you have any questions concerning technical problems please contact our Customer Services.Safety• This set of switches is suitable for controlling devices such as lights.• Make sure that theload device is turned off before connecting it tothereceiver.•Never connect a load device with a higher power rating than 1800 W.• These switches are intended for indoor use; do not expose them torain or moisture.3. Eachreceiver has anindicator in thesocket showing which of thebuttons (1, 2, 3,or 4) it is programmedfor. Theindicatorshould be removed thefirst time thereceiver isused.Iftheprogramming does not work for some reason, theprogramming must be re-done. Referto theNew programming section.Operating instructionsNote: Donot touch any of thebuttons on thetransmitter before theLED indicator has stopped flashing, otherwise theprogramming will change.1. Plugreceiver Ainto anelectrical socket.2. TheLED indicator on thereceiver will begin to flash slowly for30seconds and then goout.3. Theon/off switching of thesocket built into receiver Awill now becontrolled by button [ 1–ON ] and [ 1–OFF ]. TheLED indicator onthereceiver will come on when thereceiver is switched on and goout when thereceiver is switchedoff.4. Theother three receivers will be controlled in thesame way but withbuttons [ 2–ON ], [ 2–OFF ] [ 3–ON ], [ 3–OFF ], and [ 4–ON ], [ 4–OFF ]respectively.5. Buttons [ 1-4–ON ] and [ 1-4–OFF ] are from theoutset pre-programmedto control all four receivers simultaneously.Note: Eachtime areceiver is unplugged from anelectrical socket and plugged in again, it goes into learning mode (theLED indicator flashes slowly) for 30 seconds.In learning mode, achannel can be added or several channels can be removed. Allthechannels, (1, 2, 3, 4 and 1-4) can be aput on one receiver if desired. Referto theDeleting theprogramming and New programming sections.Deleting theprogramming1. Unplug thereceiver from theelectrical socket.2. Plugthereceiver into anelectrical socket after about 10 seconds.3. TheLED indicator on thereceiver will flash slowly for 30 secondswhile it is in learningmode.4. Pressthedesired [ OFF ] button while theLED indicator is flashingto delete theprogramming. TheLED indicator will flash quicklywhilst theprogramming is being deleted.5. Onceprogramming has been deleted, thereceiver is no longerprogrammed to any of thebuttons on thetransmitter.New programmingThereceiver needs to be programmed to one of thebuttons 1, 2, 3, 4 or 1-4 as follows:1. Unplug thereceiver from theelectrical socket.2. Plugthereceiver into anelectrical socket after about 10 seconds.3. TheLED indicator on thereceiver will flash slowly for 30 secondswhile it is in learningmode.4. Press [ 1–ON ], [ 2–ON ], [ 3–ON ] , [ 4–ON ] or [ 1-4–ON ] whilsttheLED indicator is flashing to programme thereceiver tothe transmitter.5. The LED indicator comes on when theprogramming is completed.6. Follow thesame procedure with theother receivers.TheLED indicator on thereceiver shows thestatus of thereceiver in 4differentways:•Thereceiver socket is switched off when theLED indicator is noton.•Thereceiver socket is switched on when theLED indicator ison.•TheLED indicator flashes slowly for 30 seconds when thereceiveris in learningmode.•TheLED indicator flashes quickly whilst theprogramming is beingdeleted.Care and maintenance• Unplug themains lead before cleaning theproduct.• Clean theproduct using asoft, moistcloth. Onlyuse milddetergents; never use solvents or strong, abrasive cleaning agentsfor cleaning as these can damage theproduct.DisposalThis product should be disposed of in accordance with local regulations. Ifyou are unsure how to proceed, contact your local council.SpecificationsGT-FSI-07-US (receiver)Rated voltage 120V AC, 60 Hz Maxload 1800 W (15 A) GT-9000 (transmitter)Battery 12VDC,Type A 23Frequency 433.92 MHzRange up to 25 metres (line-of-sight)Transmitter ReceiverBeforeuseInserting thetransmitter battery1. Pressthecatch on thebattery cover in thedirection of thearrowand removeit. Insert theincluded battery into thetransmitterin accordance with themarkings in thebattery compartment.Refitthebatterycover.2. The receivers are already preprogrammed for buttons 1, 2,3and 4 on the transmitter. Button E controls all three receiverssimultaneously.CautionThis device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.—Consult the dealer or an experienced radio/TV technician for help.

Navigation menu