Glynn Johnson 90J Series, 90 Series With Angle Jamb Bracket Installation Instructions 108151
User Manual: Glynn Johnson 90J Series, 90 Series with Angle Jamb Bracket Installation Instructions Installation Instructions
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
*INST.90J* INST.90J 90 Surface Overhead Holders with Angle Bracket for Flush Frame Installation Instructions These instructions cover the following models: 90H (Hold Open), 90S (Stop only), 90F (Friction), and 90SE (Special Stop Only) INSTALLATION NOTES 1. Hollow metal frames should be properly reinforced with a 3/16” (5mm) minimum thickness by 12” (305mm) minimum length plate. 2. Hollow metal doors should be properly reinforced with a 3/16” (5mm) minimum thickness by 2-1/2” (64mm) minimum width plate. 3. Stop only units are permitted on many fire door applications. However, mechanical hold-open devices that require manual release are not permitted for use on any fire door as outlined on NFPA80® or NFPA101®. Contact Glynn Johnson or your local representative for assistance. ADJUSTMENTS Hold-open tension adjustment (Hold-open model only): Using a phillips screwdriver, turn screw shown clockwise to increase hold-open tension and counterclockwise to decrease hold open tension. Hold-open tension adjustment screw Friction adjustment (Friction model only): Using a 3/32” hex wrench, turn screw shown clockwise to increase friction and counterclockwise to decrease friction. 1-877-671-7011 www.allegion.com/us *INST.90J* Customer Service INST.90J Friction adjustment screw © Allegion 2014 Printed in U.S.A. INST.90J Rev. 01/14-b INSTALLATION STEPS 1 Install angle bracket on closer. Note: Flip bracket as needed so that mounting surface is against frame. 2 Determine what type of hinge or pivot is being used on the door. Angle bracket Butt Hinge When installing closer on pull side of door, use “Pull Side Mounting Chart” regardless of hinge type and size. When installing closer on push side of door, find correct type and size of hinge or pivot on the chart below to identify correct mounting group to use on chart. Hinge Type & Size Butt Hinge 4” Wide Butt Hinge 4-1/2” Wide Butt Hinge 5” Wide Swing Clear Hinge 4” Wide Swing Clear Hinge 4-1/2” Wide (1-3/4” door) Swing Clear Hinge 4-1/2” Wide (2” door) Swing Clear Hinge 4-1/2” Wide (2-1/4” door) Swing Clear Hinge 5” Wide (1-3/4” door) Swing Clear Hinge 5” Wide (2” door) Swing Clear Hinge 5” Wide (2-1/4” door) Center Hung Pivot (1-3/4” - 2-1/4” doors) 3/4” Offset Pivot (1-3/8” door) 3/4” Offset Pivot (1-3/4” door) 3/4” Offset Pivot (2” or 2-1/4” door) SOSS 220 (2” or 2-1/4” door) Offset Pivot used to locate holder on door and frame. A Mounting Group 3 2 1 1 3 2 1 3 2 1 4 3 2 1 2 Center Hung Pivot 4 Dimensions A, B, and C (shown below) will be Center line of hinge or pivot 3 Swing Clear Hinge B C 5 Using the mounting group and GJ model numbers, find dimensions “A”, “B”, and “C” on page 3 chart. Notes on using chart: “Degrees” shown on chart represent desired hold-open degree (on hold-open, friction, and stop only models) or stop degree (on SE models). “I” = Arm length from center to center (for reference only). On hold-open, friction, and stop only models, the dead stop (DS) degree is normally 5-7 degrees beyond the holdopen degree shown on chart. The DS door position is reached when the shock spring is fully compressed. When installing on doors which open back-to-back, or against a wall or obstruction, it may be desirable to install the holder based on the dead stop angle rather than the hold-open angle. To do this, add 13/16” (21mm) to the “A” dimension on chart. This will effectively reduce the dead stop and hold-open by 5-7 degrees. This can only be done on hold-open, friction, and stop only models, but NOT on SE models. 2 CAUTION: “A” & “B” dimensions are measured from the centerline of hinge, not edge of door. *Not to be used with swing clear hinges. Push Side Mounting Chart 85 degrees 90 degrees 95 degrees 100 degrees 105 degrees 110 degrees 95 degrees 100 degrees 105 degrees 110 degrees Pull Side Mounting Chart 85 degrees 90 degrees 3 6 Mark “B” dimension (from chart) on frame. Note that “B” dimension is measured from centerline of hinge as shown. Pull side mounting Hinge/pivot centerline Hinge/pivot centerline Door Frame Frame Door Push side mounting 7 Cut out “Angle Bracket Template” from bottom of page and align on frame to locate 4 holes to drill. 8 Locate and mark “A” and “C” dimensions on door. Note that “A” dimension is measured from centerline of hinge as shown. For dead stop add 13/16” (21mm) to the “A” dimension from the chart. For more information about dead stop, see page 2 under “Notes on using chart”. 9 Drill two 3/8” (10mm) diameter channel mounting holes through door per chart and dimensions shown below. Mounting holes should be prepared only after door and frame are installed. A B Pull side mounting Push side mounting Center of hinge/pivot 9/16” (14mm) C Door opens Door opens Screw Chart 10 Install jamb bracket on the stop (see Screw Chart). 11 Install the channel on the door (see Screw Chart) Shock spring should be located on hinge end of the door. Angle Bracket Template (actual size) B For push side installation, align top of door here For pull side installation, align top of door here 4 1-3/16” (33mm) QTY 4 Jamb 4 2 Door 2 Angle 4 Brkt. Screw type #14 x 1-1/2” FPHSMS 1/4”-20 x 3/4” FPHMS 1/4”-20 x 1-1/4” OPHMS 1/4”-20 x 2-1/2” Sex bolts Wood Metal 1/4”-20 x 1/2” 4 holes Metal: #7 Drill, 1/4”-20 tap Wood: 3/16” pilot hole B
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2013:12:06 13:14:40-05:00 Metadata Date : 2013:12:06 13:14:42-05:00 Modify Date : 2013:12:06 13:14:42-05:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:bade09c7-84db-4028-b8a6-6290e2e7331b Original Document ID : xmp.did:516915126ECCE1118A0D8AD340C27D6B Document ID : xmp.id:FFC34C46A25EE311A457C8F694D1C347 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:3F337110CD5DE3118847E8FC14163402 Derived From Document ID : xmp.did:ED7F4E46944CE3119C08FBE7FC049204 Derived From Original Document ID: xmp.did:516915126ECCE1118A0D8AD340C27D6B Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2013:12:06 13:14:40-05:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 4 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools