Glynn Johnson 90J Series, 90 Series With Angle Jamb Bracket Installation Instructions 108151

User Manual: Glynn Johnson 90J Series, 90 Series with Angle Jamb Bracket Installation Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 4

*INST.90J*

INST.90J

© Allegion 2014

Printed in U.S.A.

INST.90J Rev. 01/14-b

These instructions cover the following models:

90H

(Hold Open), 90S (Stop only), 90F (Friction), and 90SE (Special Stop

Only)

ADJUSTMENTS

Hold-open tension adjustment (Hold-open model only): Using a

phillips screwdriver, turn screw shown clockwise to increase hold-open

tension and counterclockwise to decrease hold open tension.

Friction adjustment (Friction model only): Using a 3/32” hex wrench,

turn screw shown clockwise to increase friction and counterclockwise to

decrease friction.

Hold-open tension

adjustment screw

Friction

adjustment screw

Hollow metal frames should be properly reinforced with a 3/16” (5mm) minimum thickness by 12” (305mm) minimum length plate.

Hollow metal doors should be properly reinforced with a 3/16” (5mm) minimum thickness by 2-1/2” (64mm) minimum width plate.

Stop only units are permitted on many fire door applications. However, mechanical hold-open devices that

require manual release are not permitted for use on any fire door as outlined on NFPA80® or NFPA101®.

Contact Glynn Johnson or your local representative for assistance.

INSTALLATION NOTES

1.

2.

3.

Surface Overhead Holders

with Angle Bracket for Flush Frame

90

Installation Instructions

*INST.90J*

INST.90J

Customer Service

1-877-671-7011 www.allegion.com/us

Determine what type of hinge or pivot is being used on the door.

Butt Hinge Center Hung PivotOffset Pivot

Swing Clear Hinge

When installing closer on pull side of door, use “Pull

Side Mounting Chart” regardless of hinge type and size.

When installing closer on push side of door, find correct

type and size of hinge or pivot on the chart below to

identify correct mounting group to use on chart.

Dimensions A, B, and C (shown below) will be

used to locate holder on door and frame.

2

34

2

INSTALLATION STEPS

Mounting

Group

Butt Hinge 4” Wide

Butt Hinge 4-1/2” Wide

Butt Hinge 5” Wide

Swing Clear Hinge 4” Wide

Swing Clear Hinge 4-1/2” Wide (1-3/4” door)

Swing Clear Hinge 4-1/2” Wide (2” door)

Swing Clear Hinge 4-1/2” Wide (2-1/4” door)

Swing Clear Hinge 5” Wide (1-3/4” door)

Swing Clear Hinge 5” Wide (2” door)

Swing Clear Hinge 5” Wide (2-1/4” door)

Center Hung Pivot (1-3/4” - 2-1/4” doors)

3/4” Offset Pivot (1-3/8” door)

3/4” Offset Pivot (1-3/4” door)

3/4” Offset Pivot (2” or 2-1/4” door)

SOSS 220 (2” or 2-1/4” door)

3

2

1

1

3

2

1

3

2

1

4

3

2

1

2

Hinge Type & Size

Center line of hinge or pivot

B

A

C

Using the mounting group and GJ model numbers, find dimensions “A”, “B”, and “C” on page 3 chart.

Notes on using chart:

“Degrees” shown on chart represent desired hold-open degree (on hold-open, friction, and stop only models) or stop

degree (on SE models).

“I” = Arm length from center to center (for reference only).

On hold-open, friction, and stop only models, the dead stop (DS) degree is normally 5-7 degrees beyond the hold-

open degree shown on chart. The DS door position is reached when the shock spring is fully compressed.

When installing on doors which open back-to-back, or against a wall or obstruction, it may be desirable to install

the holder based on the dead stop angle rather than the hold-open angle. To do this, add 13/16” (21mm) to the “A”

dimension on chart. This will effectively reduce the dead stop and hold-open by 5-7 degrees. This can only be done

on hold-open, friction, and stop only models, but NOT on SE models.

5

1Install angle bracket on closer.

Note: Flip bracket as needed so that

mounting surface is against frame.

Angle

bracket

3

CAUTION: “A” & “B” dimensions are measured from the centerline of hinge, not edge of door.

*Not to be used with swing clear hinges.

Push

Side Mounting Chart

Pull Side Mounting Chart

85 degrees 90 degrees 95 degrees 100 degrees 105 degrees 110 degrees

85 degrees 90 degrees 95 degrees 100 degrees 105 degrees 110 degrees

Door

Frame

Mark “B” dimension (from chart) on frame. Note that “B” dimension is measured from centerline of hinge as shown.

Locate and mark “A” and “C” dimensions on door. Note that “A” dimension is measured from centerline of hinge as shown.

For dead stop add 13/16” (21mm) to the “A” dimension from the chart. For more information about dead stop, see page 2

under “Notes on using chart”.

Drill two 3/8” (10mm) diameter channel mounting holes through door per chart and dimensions shown below. Mounting

holes should be prepared only after door and frame are installed.

Install jamb bracket on the stop (see Screw Chart).

Install the channel on the door (see Screw Chart)

Shock spring should be located on hinge end of the door.

Angle Bracket Template

(actual size)

6

7

8

9

10

11

4

Door

Frame

Hinge/pivot centerline

Pull side mounting Push side mounting

Cut out “Angle Bracket Te mplate” from bottom of page and align on frame to locate 4 holes to drill.

Hinge/pivot centerline

Forpull side installation,

align top of door here

For push side installation, align

top of door here

B

B

Center of hinge/pivot

B

A

C

Pull side mounting Push side mounting

)mm33( ”61/3-1)mm41( ”61/9

Door

opens

Door

opens

#7 Drill, 1/4”-20 tap

Metal:

4 holes

3/16” pilot hole

Wood:

Screw Chart

Jamb

Door

Angle

Brkt.

#14 x 1-1/2” FPHSMS

1/4”-20 x 3/4” FPHMS

1/4”-20 x 1-1/4” OPHMS

1/4”-20 x 2-1/2” Sex bolts

1/4”-20 x 1/2”

QTY Screw type Wood Metal

4

4

2

2

4