GoPass Technology 0605G BLUETOOTH GPS RECEIVER User Manual users manual
GoPass Technology Corp. BLUETOOTH GPS RECEIVER users manual
users manual
*** USER’S MANUAL ***
FCC ID : UBH0605G
The Federal Communication Commission Statement
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction, may
cause harmful interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of more of the following
measures: -
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced Radio/TV technician for help.
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change
or modifications not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERECE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Bluetooth GPS Quick Tips
After acquiring your Bluethooth GPS Receiver, proceed with the following steps
1. Install Battery.
Fully charge the battery for at least eight hours before your first use.
Battery Low : When “LED 1” flashes green light, it signals battery low. Connect Bluethooth GPS
Receiver to a power source for continue operation and recharge simultaneously.
Charging : When battery is being charged, “LED 1” turns to red light. When the battery has
been fully charged, “LED 1” will shut off automatically.
2.Turn on Bluethooth GPS Receiver
Press the “Power Button” for 2 seconds, “LED 1” turns into steady oranage light, and “LED 2” turns
into blue flashing light. This is to activate Bluetooth pairing; it’s required only once for the first use.
Power
Button
Power
Button
LED 2
LED 1
Mini-USB
Exteranl
Power Socket
MMCX
External
Antenna
3. Activate Bluetooth function of your PDA / PC
Prior to activating the Bluetooth function of your PDA / PC, make sure the device is equipped with
Bluetooth function, and the driver software has been installed.
4. Activate Bluetooth Manager & Established New Connections
Illustrations using HP 2100 PDA as follows:
1. First, find the device with which you wish to establish connection.
2. Open “Bluetooth Manager” on your pocket pc.
3. Press “New”.
4. Press "Connect”.
4.1 4.2
4.3
4.4 4.5
Enter Pass Key "1234",
Then Press “Enter”
Click here to select
installation
Click here
Enter key
BT_GPS ****
BT_GPS
4.5 4.6
At this point, Bluetooth GPS connection has been successfully established
4.7
When “LED 1” flashes orange light twice a second, it’s indicating the BT devices have been paired.
Click
here
Click
here
BT_GPS BT_GPS
Established
connection
BT_GPS: SPP slave
6.Turn off Bluethooth GPS Receiver
Press “Power Button” for 2 seconds, “LED 2” will shut off; and the unit will be turned off.
It is suggested to close the electronic navigation map before GPS, to avoid possible PDA /PC freeze.
7. About Signals
LED 1 : a. Red light indicates Bluetooth GPS Receiver is being charged.
b. Steady orange light indicates Bluethooth GPS Receiver has been turned on, but not yet
get a position fix. It flashes once per second, after BT GPS receiver gets a position fix.
c. Flashing green light indicates battery low.
LED 2 : a. Blue light flashing swiftly, signals pairing. It flashes twice a second, signals PDA/PC and
Bluethooth GPS Receiver have been paired successfully.
Note!! Bluethooth GPS Receiver is compatible with ASUS A620BT/ A716/A730, iPAQ 2210/ 1940/
4150/ RX3715/ RX3417, Acer N30/ N35, MIO 558, O2 XDA II, Palm Zire 72/ T/ T3…, etc.
It operates on OS with Bluetooth fucntion that supports SPP.