Good Way Technology TD1000 Power Switch User Manual
Good Way Technology Co., Ltd. Power Switch
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1534164 |
| Application ID | I3oyUtNtuoLW/P7OhNRQpA== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 27.28kB (340966 bits) |
| Date Submitted | 2011-08-31 00:00:00 |
| Date Available | 2011-08-31 00:00:00 |
| Creation Date | 2011-08-24 14:20:26 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2011-08-24 14:28:07 |
| Document Title | untitled |
Power Switch User’s Manual ABOUT THIS MANUAL This manual is designed for use with the Power Switch. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage. SAFETY INSTRUCTIONS Always read the safety instructions carefully: Keep this User’s Manual for future reference Keep this equipment away from humidity If any of the following situation arises, get the equipment checked by a service technician: x The equipment has been exposed to moisture. x The equipment has been dropped and damaged. x The equipment has obvious sign of breakage. x The equipment has not been working well or you cannot get it to work according to the User’s Manual. COPYRIGHT This document contains proprietary information protected by copyright. All right are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. TRADEMARKS All trademarks and registered trademarks are the property of their respective owners or companies. Table of Contents 1. Introduction ............................................................................................................1 Features..............................................................................................................2 Package Contents...............................................................................................2 LED Indicator ......................................................................................................2 Z-Wave .............................................................................................................2 Wireless Range ..................................................................................................3 2. Installation ..............................................................................................................4 Hardware Connection .........................................................................................4 Product Description.............................................................................................5 Installation Requirements ...................................................................................5 Installing the Power Switch ................................................................................ 6 3. Specifications.........................................................................................................7 4. Regulatory Compliance .........................................................................................8 FCC Conditions ..................................................................................................8 WEEE Information ..............................................................................................8 ii 1. Introduction The Power Switch allows you to turn on/off the attached appliance, electronic device or lamp wirelessly by using Z-Wave protocol remote control. You can control the attached load in your home through PC connectivity with a Z-Wave USB dongle when you are away from home.ʳ ʳ ʳ ʳ ʳʳʳ Note: To avoid any dangerous accident, please don’t use this product on the plug of extended power line or else instead of wall plug. ʳʳ ʳ ʳ ʳ ʳ Features Simple plug and play installation. Support electronic appliance or lamp with maximum loading of 1500W Stand-by power consumption: 0.6 W Control On/Off function manually with knob button or remote control by PC equipped with Z-Wave certified USB dongle. Fully compatible with Z-Wave enabled network and capable of communicating with any Z-Wave certified device. All products other then the Power Switch itself are sold separately. Package Contents Power Switch x1 User’s Manual x1 LED Indicator LED Color Power Red Link Description Power Switch Power on. Green Z-Wave RF transfer or receive. Z-Wave Z-Wave is a state-of-the-art wireless technology used as a standard for wireless home control. It is a next-generation wireless ecosystem that lets all your home electronics talk to each other, and to you, via a controller or gateway. It uses simple, reliable, low-power radio waves that easily travel through walls, floors and cabinets. All products featuring the Z-Wave logo are certified to work with one another. Wireless Range The Power Switch is made wireless by Z-Wave technology. Typical range for a wireless module is approximately 100 feet. When installing the module consider an open area with little obstruction for the best signal and performance. Avoiding the obstruction between the module and controller may make a negative effect on wireless performance and range. 2. Installation Hardware Connection LED Z-Wave Enabled Outlet Plug Switch Button Product Description Below is a description of button, light and plugs for the Power Switch. Z-Wave Enable Outlet This outlet is a socket where the device or equipment you wish to control should plug into, such as LCD monitor. Note that any device plugged into this outlet must NOT exceed 1500 watts. LED The light will blink to indicate that the module has been entered “Program Mode” or when it is communicating wirelessly to the Z-Wave controller (i.e. Z-Wave Dongle). Switch Button When the Power Switch has been installed, pressing the switch button will manually turn the attached device on or off. When primary controller is waiting for inclusion or exclusion to setup Z-Wave Network, please press this button could add or remove this device from Z-Wave network. Wall Outlet Plug Located on the back of the Power Switch, the plug is used to plug your module into an available wall outlet in your home or office. Installation Requirements To install this product you must have Z-Wave enabled controller, such as Z-Wave Dongle, to make an association with Power Switch. Installing the Power Switch NOTE ======================================================= Before you install or use this Power Switch, please install your Z-Wave controller first and make an inclusion for your Z-Wave device. Not all Z-Wave enabled remote controls have the same installation process. Actual instructions may vary; it depends on the software that Z-Wave controller provided. ============================================================ 1. Please plug the Power Switch into an available wall outlet near the load to be controlled in your desired location of your office or home. 2. Operate your control panel from Z-Wave controller to include the Power Switch in your network. 3. Once the Power Switch has been included in your network, you may see or get some information about your Power Switch on your control panel or else to confirm that has been added. If not, try the process again or try deleting this switch from Z-Wave controller first. 4. When the Power Switch has been added into Z-Wave control panel successfully, you will need to configure it to a specific button or other else on your control panel. Refer to your Z-Wave control panel for instructions on how to do this. 5. Now you can plug your electric device into the Z-Wave enabled outlet on the Power Switch and control your device on or off via your own PC. 3. Specifications Item Description Protocol Z-Wave (Binary Switch Command Class) Frequency 908.42MHZ( US) Transceiver Yes Operating Voltage AC110~120V/60Hz Max Loading 1500W Stand-by power consumption 0.6 W Green :Z-Wave RF transfer or receive LED Indicator Red : Power Switch power on Switch On / Off (Side Knob Button) Data Rate Up to 40 kbps Operation Range Up to 100 feets Application Indoor use Operation temperature: 10 ~ 40 ̓C Working Environment Storage temperature: -10 ~ 80 ̓C 67.9mm x 89.3mm x 57mm, Dimensions (Lx W x H) (Included the height of wall outlet plug) Housing Plastic PC 945 Flame Class UL 94 V-0 Compliance FCC, UL, Z-Wave Specifications are subject to change without further notice 4. Regulatory Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation WEEE Information For EU (European Union) member users: According to the WEEE (Waste electrical and electronic equipment) Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Modify Date : 2011:08:24 14:28:07+08:00 Create Date : 2011:08:24 14:20:26+08:00 Page Count : 11 About : uuid:87651e28-65cb-447e-bc48-4f332d65c2a6 Producer : Acrobat Distiller 6.0 (Windows) Creation Date : 2011:08:24 14:20:26+08:00 Mod Date : 2011:08:24 14:28:07+08:00 Metadata Date : 2011:08:24 14:28:07+08:00 Document ID : uuid:aa142979-fbca-4d82-86a2-ca6b22abd378 Format : application/pdf Title : untitled Has XFA : NoEXIF Metadata provided by EXIF.tools