Good Way Technology TD11000Z2 Z-Wave Roller Shutter Controller User Manual
Good Way Technology Co., Ltd. Z-Wave Roller Shutter Controller
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3966014 |
| Application ID | OEW3giZjipoMS7E5WRJebw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 61.99kB (774937 bits) |
| Date Submitted | 2018-08-16 00:00:00 |
| Date Available | 2018-08-16 00:00:00 |
| Creation Date | 2018-08-14 16:40:52 |
| Producing Software | Microsoft® Word 2016 |
| Document Lastmod | 2018-08-14 16:40:52 |
| Document Title | User Manual |
| Document Creator | Microsoft® Word 2016 |
| Document Author: | Henry Chen |
The Power level Command Class defines RF transmit power (0x0A) controlling commands useful when installing or testing a network. The commands make it possible for supporting controllers to set/get User's Manual the RF transmit power level of a node and test specific links between nodes with a specific RF transmit power level. Introduction 【BASIC command class】 11 (0x0B) power changed percenta ge to send the power report Set the 2 time interval of reporting watts in seconds Set the 2 time interval of reporting KWH in seconds 1 - 100: 1% - 100% 0, 300 60 sec 32767 0：Disable 60 - 32767: 60 - 32767sec 0, 3600 60 32767 0：Disable 60 - 32767: 60 - 32767sec Z-Wave Roller Shutter Controller is an ideal for the remotely electric Control the roller shutter to be opened or closed after receiving the motor controller. It is used to control the motors of rollers, shades, BASIC_SET command. blinds, venetian blinds and similar sun shade, which are single phase To be opened: AC powered. The module can be controlled either through a Z-Wave [Command Class Multilevel, Multilevel Set, Value = 0xFF] network or through the wall switch, and measures power To be closed: consumption of motor. [Command Class Multilevel, Multilevel Set, Value= 0x00] Z-Wave Roller Shutter needs to motor calibration before use, please To be the percentage of full opened position: refer to CONFIGURATION command class parameter 0x01. Z-Wave [Command Class Multilevel, Multilevel Set, Value = 0x01~0x63] Roller Shutter’s positioning calibration does not apply to motor 【SWITCH MULTILEVEL command class】 without obstacle detection, using this function may cause Control the roller shutter to be opened, closed, stopped or be the unpredictable problems, please make sure your motor has obstacle percentage of full opened position after receiving the SWITCH detection function before positioning calibration. MULTILEVEL command. 【ASSOCIATION command class】 To be opened: The device can be set 1 auto-report ID in Group 1. [Command Class Multilevel, Multilevel Set, Value = 0xFF] The device sends an unsolicited command to the configured To be closed: destinations when triggered by an event. [Command Class Multilevel, Multilevel Set, Value= 0x00] Group1:"Lifeline" : To be the percentage of full opened position: 【ASSOCIATION GRP INFO command class】 [Command Class Multilevel, Multilevel Set, Value = 0x01~0x63] The purpose of the Association Group Information (AGI) Command To be stopped: Class is to allow a device to report the capabilities of each [Command Class Multilevel, association group supported by the device. SWITCH_MULTILEVEL_STOP_LEVEL_CHANGE] 【SWITCH_BINARY command class】 【CONFIGURATION command class】 Control the roller shutter to be opened or closed after receiving the This class is used for setting certain vendor specific configuration SWITCH BINARY command. variables. See the following table for configuration variables: Parameter Name Size Range Default Description (byte) value Positioni 1 0-1 0 0: Disable (0x01) ng 1: Executing Calibratio calibration External 1 0-1 0 0: Enable external (0x02) switch switch Protectio 1: Disable external switch When 00 0: Disable automatic (0x03) the door 32767 closing is 1 - 32767: The door opened, will be closed set the automatically in 1 delay 32767sec time for automati c closing. When 00 0: Disable automatic (0x04) the door 32767 notification is open, 1 - 32767: The set the notification will be delay sent automatically in time for 1 - 32767sec automati notificati on. Set the 1 0-1 0 0: Roller Shutter (0x05) operatio 1: Venetian n mode (up/down and slate rotation) Set the 1 0-6 0 Angles of blinds (0x06) angle of 0：0∘ blinds 1：30∘ 2：60∘ 3：90∘ 4：120∘ 5：150∘ 6：180∘ Set the 1 0 - 127 15 0：Disable. (0x07) slats (1.5sec 1 - 127: 0.1 - 12.7 sec turning time Set the 1 0 - 127 0 0：No offset time (0x08) delay 1 - 127: 0.1 - 12.7 sec time to start the motor up to the blade Set the 1 0 - 127 0 0：No offset time (0x09) delay 1 - 127: 0.1 – 12.7 sec time to start the motor down to the blade 10 Set the 1 0 - 100 0 0：Disabled To be opened: Package Contents ■ Z-Wave Roller Shutter Controller ■ User Manual x1 x1 Command Class Device Information GENERIC_TYPE_SWITCH_MULTILEVEL SPECIFIC_TYPE_CLASS_C_MOTOR_CONTROL z-wave protocol Command Class Node Info COMMAND_CLASS_ZWAVEPLUS_INFO_V2 COMMAND_CLASS_VERSION_V3 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 COMMAND_CLASS_POWERLEVEL_V1 COMMAND_CLASS_SWITCH_MULTILEVEL_V3 COMMAND_CLASS_CONFIGURATION_V1 COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 COMMAND_CLASS_SWITCH_BINARY_V1 COMMAND_CLASS_METER_V3 COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4 COMMAND_CLASS_SUPERVISION_V1 COMMAND_CLASS_Transport_Service_V2 COMMAND_CLASS_SECURITY_V1 COMMAND_CLASS_SECURITY_2_V1 The Below listed Command Class are all supported the S ecurity S2 COMMAND_CLASS_VERSION_V3 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 COMMAND_CLASS_POWERLEVEL_V1 COMMAND_CLASS_SWITCH_MULTILEVEL_V3 COMMAND_CLASS_CONFIGURATION_V1 COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 COMMAND_CLASS_SWITCH_BINARY_V1 COMMAND_CLASS_METER_V3 COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4 COMMAND_CLASS_SUPERVISION_V1 Detailed description of each command class 【ZWAVEPLUS INFO command class】 The Z-Wave Plus Info Get Command is used to get additional information of the Z-Wave Plus device in question. 【VERSION command class】 The user can enquire the version of the unit using VERSION_GET command. It will return VERSION_REPORT Command. Version Report Command: [Command Class Version, Version Report, Z-Wave Library Type, ZWave Protocol Version, Z-Wave Protocol Sub Version, Application Version, Application Sub Version] 【MANUFACTURER SPECIFIC command class】 The user can use the Manufacturer Specific Get Command to request manufacturer specific information from another node. Manufacturer Specific Report Command: [Command Class Manufacturer Specific, Manufacturer ID 1, Manufacturer ID 2, Product Type ID 1, Product Type ID 2, Product ID 1, Product ID 2] 【DEVICE RESET LOCALLY command class】 The Device Reset Locally Command Class is used to notify central controllers that a Z-Wave device is resetting its network specific parameters. 【POWERLEVEL command class】 12 (0x0C) [Command Class SWITCH_BINARY, Set Value = 0xFF] To be closed: [Command Class SWITCH_BINARY, Set Value = 0x00] 【METER command class】 The Meter Command Class is intended for Z-Wave enabled devices capable of reporting energy measurements in addition to any main functionality or features e.g. an appliance module reporting the current consumption of the connected load. The Meter command class not support V1&V2 version. And it will take about 3 seconds to show the meter report on the request sending device. 【FIRMWARE UPDATE META DATA command class】 Support OTA (On-The-Air) firmware update function. 【COMMAND_CLASS_SECURITY_V1】 【COMMAND_CLASS_SECURITY_2_V1】 This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products. Product Overview Product Dimensions Application Diagram Main Diagram Function Add for Inclusion - Notes for the Diagram D1 D2 S1 S2 Pairing Button Operation Neutral lead Live lead Output for motor UP Output for motor DOWN Input for switch/push button UP Input for switch/push button DOWN Include/ Exclude/ Reset Button Device Installation 1. Before installation make sure the voltage supply is disconnected. 2. Put the device into a small box (such as wall box or small plastic box and etc.) near the motor to avoid direct exposure danger in the air and to the water. 3. Connect the motor of Roller Shutter and Switch in accordance with the wiring diagram presented on Fig. 1 (roller blinds, venetian blinds). Operation 1. Put the Z-Wave Controller into inclusion mode, and press the pairing button 3 times in 2 seconds to include the module. 2. Put the Z-Wave Controller into inclusion mode, and press the “external swtich1” or “external swtich2” 3 times in 2 seconds to include the module. Remove for 1. Put the Z-Wave Controller into Exclusion exclusion mode, and press the pairing button 3 times in 2 seconds to exclude the device. 2. Put the Z-Wave Controller into inclusion mode, and press the “external swtich1” or “external swtich2” 3 times in 2 seconds to include the module. Reset 1. Press the pairing button 3 times in 2 seconds and press and hold the pairing button for more than 5 seconds at the 3rd time. 2. The module is excluded and restores to factory default setting. 3. Then the module will be in autoinclusion mode for 2 minutes. Please use this procedure only when the network primary controller is missing or otherwise inoperable. Positioning Positioning calibration is a process during calibration which a Roller Shutter learns the position of the limit switches and a motor characteristic. Calibration is mandatory in order for the Roller Shutter to correctly recognize a roller blind position. The procedure consists of an automatic, full movement between the limit switches (up, down, and up again). There are three kinds of positioning calibration operation as follows: 1. Parameter Setting: Parameter 1(0x01), Size 1(byte), Value 1. 2. Pairing Button: Press and hold the button for 6 to 10 seconds, release the button (less than 2 seconds), and then click the button (less than 2 seconds) 3. External Switch: Use the same external switch (S1 or S2), turn on and off 3 times. Turn ON =>OFF => ON=> OFF=> ON=> OFF (Turn ON: lasts 3 to10 seconds), Turn OFF: less than 2 seconds) Note: If an emergency is encountered during the positioning calibration process, please click the external switch, the pairing button, or the APP to abort the positioning calibration processes. Notice: Including a node ID allocated by Z-WaveTM Controller means “Add” or “Inclusion”. Excluding a node ID allocated by ZWaveTM Controller means “Remove” or “Exclusion”. LED Indicator LED Signal LED OFF Red & Green blinking by turns Solid Green Figure 1. Roller Shutter wiring diagram 4. Locate the antenna far from metal elements (as far as possible) 5. Do not shorten the antenna. 6. Turn on the power supply keeping the necessary safety precautions. 7. Include the module into the Z-Wave network, please refer to the "Operation" section for “Inclusion” operating instructions. 8. Executing the positioning calibration process, please refer to the "Operation" section for “Positioning calibration” operating instructions. CAUTION! ! Read this manual before attempting to install the device! Failure to observe recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer will not be held responsible for any loss or damage resulting from not following the instructions of operating manual. ! Any maintenance work on controlled devices may be performed only after the power supply has been disconnected. ! Do not connect the module to loads exceeding recommended values. Connect the module only in accordance with the diagram presented in the manual. Improper connections may be dangerous. Green blinking twice per second for 3 seconds Red blinking twice per second for 3 seconds Green blinking twice per second for 2 minutes Red blinking twice per second Status Power OFF Power ON (No node ID) Power ON (Included) (1) Inclusion process success (2) Exclusion process success (3) Parameter setting success (4) Positioning calibration success (1) Inclusion process failed (2) Exclusion process failed (3) Parameter setting failed (4) Positioning calibration failed Auto Inclusion Mode Overload Protection Specification Wireless Type Frequency Operating Distance Power Supply Rated load current of AC output (resistive load) Rated power of Motor Power measurement accuracy Electricity Consumption Z-Wave Plus EU: 868.4 MHz US: 916.0 MHz up to 100m outdoors ; up to 30m indoors 110 -230 VAC ±10% 50 / 60 Hz 2 @ 5A (230 VAC) Motor under 170W P = 0-40 W, ± 2 W; P > 40 W, ±3% <0.5W LED Red /Green LED*1 Switching Relay x 2 Data Rate 100 kbps Operation temperature -10°C ~ 40°C Dimensions (L x W x H) 45.5 x 44.8 x 20.3 mm *Specification is subject to change without prior notice. External Switch Operation S1 Turn OFF Turn ON Turn OFF Turn ON S2 Turn OFF Turn OFF Turn ON Turn ON Motor Action STOP UP DOWN STOP Regulatory Compliance CE Caution Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1,000 MHz frequency range with power levels ranging up to 500 mW; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive. FCC Caution This device complies with Part 15 of the FCC rules standard. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. WEEE Information For EU (European Union) member users: According to the WEEE (Waste electrical and electronic equipment) Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product. Z-Wave Plus This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. This device must be used in conjunction with a Security Enabled ZWave Controller in order to fully utilize all implemented functions. Security S2 Security S2 is supported with the Authenticated and UnAuthenticated levels of security. The Authenticated level requires the user to enter the PIN code or QR code printed on the box of the Roller Shutter. The UnAuthenticated level does not require the PIN code. Both security levels will encrypt nearly all communication using AES-128 encryption to ensure reliable and secure communication. SmartStart Sigma Designs technology makes installation easy and secure. Simply install Roller Shutter into a wall and it will automatically attempt to join the Z-Wave network. During the inclusion process, your home automation system will ask for a PIN code or to scan a QR code. The pin code is printed on the back of Roller Shutter along with the QR code. Simply enter the PIN code or scan the QR code with a compatible device. Each QR code is unique for every device. SmartStart uses the latest Security S2 encryption technology for all radio communication. It is completely backwards compatible with non-SmartStart systems if your home automation system doesn’t support it yet. Ex: WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions. - Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury - All wiring interconnecting with this controller is non-isolated hazardous live parts. - The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. - Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. - Do not use if repair or adjustment is necessary. - Do not allow children to play with fixed controls. Keep remote controls away from children. - The drive shall be disconnected from its power source during cleaning, maintenance and when replacing parts. - Indoor use only. - Never install independent switch for each S1 and S2, to prevent the activation on D1 and D2 at the same time. - Material used only for the 16 AWG copper wires and the suggested strip length is 4.5 ~ 5 mm. - Equipment shall not be interconnected with the output of another power source. - High Voltage - Disconnect power supply before servicing. - Risk of Electric Shock - More than one disconnect switch may be required to de-energize the device before servicing.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 3 Language : zh-TW Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Microsoft® Word 2016 Creator : Henry Chen Creator Tool : Microsoft® Word 2016 Create Date : 2018:08:14 16:40:52+08:00 Modify Date : 2018:08:14 16:40:52+08:00 Document ID : uuid:9C3D1D45-65B4-469E-88E0-D6D35147624B Instance ID : uuid:9C3D1D45-65B4-469E-88E0-D6D35147624B Author : Henry ChenEXIF Metadata provided by EXIF.tools