Good Way Technology TD14000Z1 R.G.B.W Color LED Dimmer User Manual TD14010Z1 Manual V4 0
Good Way Technology Co., Ltd. R.G.B.W Color LED Dimmer TD14010Z1 Manual V4 0
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3423271 |
| Application ID | l4sYa062J3BJzTnhz+YoCg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 35.96kB (449495 bits) |
| Date Submitted | 2017-06-13 00:00:00 |
| Date Available | 2017-06-14 00:00:00 |
| Creation Date | 2017-10-22 20:54:08 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-10-22 20:54:08 |
| Document Title | TD14010Z1_Manual_V4.0 |
| Document Creator | PDFCreator Version 1.2.3 |
| Document Author: | g01122 |
R.G.B.W. Color LED Dimmer ID Name Size Range Default Description value 1 byte 1-3 1: Normal Mode 2: Brightness Mode 3: Rainbow Mode 1 byte 1-5 1: Ocean 2: Lightning 3: Rainbow 4: Snow 5: Sun 1 byte 0x03- 3 Adjust Scene delay time: 0xFE 1. When Value is 1(0x01)~127(0x7F), the delay duration is 1 sec.~127 sec. 2. When Value is 128(0x80)~255(0xFE), the delay duration is 1 min.~127 min. Switch mode (0x02) User's Manual Auto Scene (0x03) Mode Set Introduction The RGBW Controller is a universal, Z-Wave compatible RGB / RGBW controller. The RGBW Controller uses PWM output signal, which enables it to control LED, RGB, RGBW strips, Halogen lights. Controlled devices may be powered by 12 or 24 VDC. All IN and OUT terminals can be configured for LED control. Auto Scene (0x04) Mode Duration Package Contents ■ R.G.B.W. Color LED Dimmer ■ 3M Double-sided Adhesive Sticker ■ User Manual ■ 18AWG copper wire ■ Conductive connector x1 x1 x1 x1 x1 Figure 3. Connecting push switch ASSOCIATION command class The Module can be set 1 auto-report ID in Group 1. The Module will send BASIC_REPORT to device associated in Group 1 when correspond Device is activated. FIRMWARE UPDATE META DATA command class, version 2 Support OTA (On-The-Air) firmware update function. Product Overview Command Class Multilevel Switch Device Information Figure 4. Connecting conductive connector 40.5 GENERIC_TYPE_SWITCH_MULTILEVEL SPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL 4. According to the Figure 4.,you can use the 18AWG copper wire and conductive connector to extend the connection of the power supply. 5. In the status of the factory default (Not Paired), the red light and green light will blink by turns, eg. red, green, red, green, etc.. 6. Include the R.G.B.W. Color LED Dimmer into the Z-wave network, press 3 times in 2 seconds. If the device is properly included, the green light will remains on. 7. Exclude the R.G.B.W. Color LED Dimmer into the Z-Wave network, press 3 times in 2 seconds. If the device is properly excluded, the green light will blink and the data will be reset to the factory default values. 8. Please pull out the antenna and keep it at 90 degree to enhance the RF signals. 9. Support auto inclusion: Install the device, connect with the power, and the auto inclusion function will work in about 2 minutes. 10. Support remote exclusion: Through configuration setting. Please refer to the following table. Multilevel Switch Command Class COMMAND_CLASS_ZWAVEPLUS_INFO_V2 COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_DEVICE_RESET_LOCALLY, COMMAND_CLASS_POWERLEVEL_V1 COMMAND_CLASS_BASIC_V1 COMMAND_CLASS_SWITCH_MULTILEVEL_V2 COMMAND_CLASS_SWITCH_COLOR_V2 COMMAND_CLASS_CONFIGURATION_V1 COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 COMMAND_CLASS_SWITCH_BINARY_V1 COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 32 14.5 Detailed description of each command class ZWAVEPLUS INFO command class The Z-Wave Plus Info Get Command is used to get additional information of the Z-Wave Plus device in question. BASIC command class The module will be turned ON or OFF after receiving the BASIC_SET command. To be turned on: [Command Class Basic , Basic Set, Basic Value = 0x01~0x63 in percentage; FF set to last value] To be closed: [Command Class Basic , Basic Set, Basic Value = 0x00] SWITCH MULTILEVEL command class The module will be turned ON or OFF after receiving the SWITCH_ MULTILEVEL_SET command. To be turned on: [Command Class Multilevel , Multilevel Set, Basic Value = 0x01~0x63 in percentage; FF set to last value] To be closed: [Command Class Multilevel , Multilevel Set, Basic Value = 0x00] SWITCH COLOR command class This class is used for Color setting. See the following table for configuration variables: Capability ID Color State Level 0 (0x00) Warm White 0x00-0xFF 2 (0x02) Red 0x00-0xFF 3 (0x03) Green 0x00-0xFF 4 (0x04) Blue 0x00-0xFF DEVICE RESET LOCALLY command class The Device Reset Locally Command Class is used to notify central controllers that a Z-Wave device is resetting its network specific parameters. VERSION command class The user can enquire the version of the unit using VERSION_GET command. It will return VERSION_REPORT Command. Version Report Command: [Command Class Version, Version Report, Z-Wave Library Type, Z-Wave Protocol Version, Z-Wave Protocol Sub Version, Application Version, Application Sub Version] MANUFACTURER SPECIFIC command class The user can use the Manufacturer Specific Get Command to request manufacturer specific information from another node. Manufacturer Specific Report Command: [Command Class Manufacturer Specific, Manufacturer ID 1, Manufacturer ID 2, Product Type ID 1, Product Type ID 2, Product ID 1, Product ID 2] CONFIGURATION command class This class is used for setting certain vendor specific configuration variables. See the following table for configuration variables: ID Name Switch Type (0x01) Size Range Default Description value 1 byte 1-2 1:Toggle Mode 2: Momentary Mode ID F0 Device Installation Size 1 byte Value Warning! 1) The RGBW Controller is suggested to operate in low voltage circuits of 12VDC or 24VDC. Connecting higher voltage load may result in the RGBW Controller damage. Please refer to the following table. 1. Prepare the following items: - RGBW strip(12V or 24V) x1 - Stranded wire x5 - Power adapter x1 Current of RGBW Strip High current Low current 2. Figure 1. Terminals Description. Include/Exclude Button IN4 IN3 IN2 IN1 GND 12/24VDC Figure 1. Terminals Description 3. Connect the R.G.B.W. Color LED Dimmer according to Figure 2., or Figure 3. - First, connect RGBW strip with output channel(R,G,B,W) - Second, connect the power supply. If the device is properly connected, the RGBW strip will blink once. Note that the device must be powered by a dedicated stabilized power adapter. Stranded Wire 18 AWG 22 AWG 2) The RGBW Controller must be powered by the same voltage as the connected light source. I.e. if controlling 12V LED strip, the module must be connected to 12V power supply. Similarly, if controlling 24V RGBW strip, the RGBW Controller must be powered by 24V voltage supply. 3) The RGBW Controller must be powered by 12VDC or 24 VDC stabilized power supply with outputs load capacity matched to loads voltage. 4) In case of connecting long RGBW/RGB/LED strips voltage drops may occur, resulting in lower light brightness further from R/G/B/W outputs. To eliminate this effect it's recommended to connect few shorter strips in parallel connection instead of one long strip connected serially. Maximum recommended wire length, used to connect R/G/B/W outputs with a RGBW/RGB/LED strip is 5 m. Observe connected loads manufacturer recommendations towards connection wire diameter. 5) For connection of IN1~IN4, it is suggested that you connect the 4 inputs individually to the same type of deivce. The devices can be as follows: the toggle switch, or the push switch. 6) Please note that re-including the product will reset the data to the default values. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. Glossary of terms Include/Exclude Button - Inclusion/exclusion, press 3 times in 2 seconds Figure 2. Connecting toggle switch 12/24VDC - Power supply signal IN4 - Switch input 4 GND - Power supply ground signal R - Output assigned to IN1 IN1 - Switch input 1 G - Output assigned to IN2 IN2 - Switch input 2 B - Output assigned to IN3 IN3 - Switch input 3 W - Output assigned to IN4 LED Dimmer Application Speed: Tick the box to select Slow/ Medium/ Fast. Specification Color Control Control the color with Hue (the palette on the top), Value (the first scroll bar), and Saturation (the second scroll bar). Item Description Power Supply 12 / 24V DC PWM output frequency 488Hz Electricity consumption 12V: 0.48W; 24V: 0.72W Radio signal power 1mW LED Indicator Red/Green *1 Button Inclusion/Exclusion Protocol Z-Wave Plus Operation Range 100 feet (About 30M) Housing Plastic (PC8600) Dimensions(L*W*H) 40.5*32*14.5mm Rated output power 7A for single output channel, 13A at max. (3.25A for R.G.B.W. single output channel is suggested) Max load (e.g. halogen bulbs) At 12V- 192W combined At 24V- 384W combined Application Indoor use Temperature Storage: -20℃~70℃ Operation: 0℃~40℃ NOTE: Lightning Scene Mode does not support Speed adjustment. Multilevel Switch Turn the switch ON/OFF (the button on the bottom), and adjust the brightness level (the scroll bar). LED Indicator Status Not Paired Paired up LED Signal Remark Red& Green blinking by turns Solid Green (Interval: 1sec.) External Controller Region Applied Frequency Data Rate EU 868.42 MHz 9.6 kbps EU 868.4 MHz 40 kbps US 908.42 MHz 9.6 kbps US 908.4 MHz 40 kbps US 916 MHz 100 kbps JP 922.5 MHz 100 kbps JP 923.9 MHz 100 kbps JP 926.3 MHz 100 kbps *Specification is subject to change without prior notice. Special Scene Effect Select the scene mode (the first drop-down menu), and the speed (the second drop-down menu). Input type Remark Momentary Momentary switch Toggle Toggle switch Input operating mode Remark Normal Each given switch key assigned to one output channel Brightness All channels are controlled together Rainbow Scene Mode: Tick the box to select from Ocean, Lightning, Rainbow, Snow, and Sun. Transition through all colours spectrum (Operates on RGB/RGBW channels only) Device Application The RGBW Controller may control: • 12 / 24VDC powered RGB strips • 12 / 24VDC powered RGBW strips • 12 / 24VDC powered LED strips, bulbs, etc. • 12 / 24VDC powered halogen lights Additional features: • controlled by momentary or toggle switches Regulatory Compliance CE Caution Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1,000 MHz frequency range with power levels ranging up to 500 mW; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive. FCC Caution This device complies with Part 15 of the FCC rules standard. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. WEEE Information For EU (European Union) member users: According to the WEEE (Waste electrical and electronic equipment) Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product. Z-Wave Plus This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 1 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:462d001e-9702-11f2-0000-02c7314339d4 Producer : GPL Ghostscript 9.18 Modify Date : 2017:07:02 05:17:21Z Create Date : 2017:07:02 05:17:21Z Creator Tool : UnknownApplication Document ID : uuid:462d001e-9702-11f2-0000-02c7314339d4 Format : application/pdf Title : UntitledEXIF Metadata provided by EXIF.tools