Gouldin Technologies WP460 Watchman User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3833569
Application ID	HJraS2SsycHK5eeJQHCoGg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	373.16kB (4664470 bits)
Date Submitted	2018-04-28 00:00:00
Date Available	2018-04-28 00:00:00
Creation Date	2018-03-02 16:58:14
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-04-28 18:30:14
Document Title	User Manual
Document Creator	Acrobat PDFMaker 18 for Word
Document Author:	Scarlett Brown

2018
WP460 Series
Quick Install Guide
CellGate Support: 972-231-1999 option 2
Ethernet
Switch
Interface Circuit Board
App Credentials and Device Information
1.
After full review of the provided Quick Install Guide, power up the Watchman unit.
2.
Allow at least 10 minutes after power up for cellular signal to connect. (The device is not embedded in other cell
phone devices, but by inserting Ethernet cable into the only network ports on the it that can connect to 3G/34 router,
then to Cellgate Mobile Connect app. The protocol is TCP/IP.)
3.
■ On WP460 series, press the “Enter Code” button on the
home screen of the Watchman unit, enter the device
number, and then press Open.
4.
Wait 60 seconds.
5.
Login to the Cellgate Mobile Connect app with the
username and password provided above.
6.
Select the device number for the unit you’re currently activating.
7.
Select the “Internal Camera”.
8.
Press “Take Picture”.
WP460 Series
9.
Confirm a picture was received.
10. Press “Back” in the top left.
11. Select the Watchman Gate
12. Press the “Open Momentarily” button. The gate should
open for the duration set in the timer and the Watchman
should audibly confirm “Access Granted”.
12a. If the Watchman does not say “Access Granted” and the gate does not open, please check the unit’s
network connection and power.
12b. If the Watchman says “Access Granted” and the gate does not open, please check the gate trigger wires
that run between the Watchman and the gate operator.
13. After the gate has closed enter the Access Code from Page 1 into the keypad then press the key symbol
Open. The gate should open and the Watchman should say “Access Granted”. If not, see options 12a or 12b.
14. Login to the Watchman app using the same credentials. See top of Page 1. *note, accept ALL app permissions
or
15. After login initiate a call from the Watchman unit.
WP460 Series
16. During the call you should see live video feed in the Watchman app and hear audio from both the app and the
Watchman unit.
17. Press the Open button. You should hear a tone from the Watchman unit and the gate should open.
18. Congratulations! You have successfully activated the Watchman! Please leave the customer a key for their
Watchman.
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Scarlett Brown
Comments                        : 
Company                         : 
Create Date                     : 2018:03:02 16:58:14-06:00
Modify Date                     : 2018:04:28 18:30:14-07:00
Source Modified                 : D:20180302225756
Subject                         : 
Has XFA                         : No
Language                        : EN-US
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2018:04:28 18:30:14-07:00
Creator Tool                    : Acrobat PDFMaker 18 for Word
Document ID                     : uuid:88001720-3585-4793-8b55-af8f4ca5de8e
Instance ID                     : uuid:67f8ec7b-9419-4496-ae2a-71ced5d40a81
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : Scarlett Brown
Producer                        : Adobe PDF Library 15.0
Keywords                        : 
Page Layout                     : OneColumn
Page Count                      : 7

EXIF Metadata provided by EXIF.tools