Graco 310643T Displacement Pump Users Manual Pump, Repair, English

257146 3a177695-9978-4cc8-8c8e-353aa425e8f3 Graco Marine Sanitation System 257146 User Guide |

: Graco Graco-310643T-Displacement-Pump-Users-Manual-686120 graco-310643t-displacement-pump-users-manual-686120 graco pdf

Open the PDF directly: View PDF .
Page Count: 20

Download
Open PDF In Browser	View PDF

Repair

Displacement Pump

310643T
EN

3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure
Model 248204, Series A
Ultrar Max II and Ultimate Mx II 695 and 795
ASM Zip--Sprayt 2700 Plus, 3100 Plus
ASM AllPro Mach 8600 Plus and 11000 Plus
ASM H2700 Plus

Model 255968, Series A
ASM 3600G Plus

Model 248205, Series A
Ultra Max II and Ultimate Mx II 1095 and 1595

Model 249059, Series A
TexSprayt Mark V

Model 249057, Series A
TexSpray Mark V

Model 277069, Series A
LineLazert IV 3900, R300

Model 277070, Series A
LineLazert IV 5900

Model 253056, Series A
Mark IV

Model 257146, Series A
Ironman 300E and Ironman 500G
Important Safety instructions
Read all warnings and instructions in this manual.
Save these instructions.

8016A

Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts, Pump
248204, 255968 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
248205, 249057, 249059, 277070, 257146 . . . . .
253056 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16
17
18
20

WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
D Do not exceed the maximum working pressure temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
D Use fluids and solvents compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read manufacturer fluid and solvent warnings.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not alter or modify equipment.
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use equipment only for its intended purpose. Call your Graco distributor for information.
D Do not use 1,1,1--trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in pressurized aluminum equipment. Such use could result in a
chemical reaction, with the possibility of explosion.
D Comply with all applicable safety regulations.

MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
D Keep clear of moving parts.
D Do not operate equipment with protective guards or covers removed.
D Pressurized equipment can start without warning. Before checking, moving or servicing equipment,
follow the Pressure Relief Procedure on page 3. Disconnect power cord.

SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks or ruptured components will pierce skin. This may look like
just cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
D Do not point the gun at anyone or at any part of the body.
D Do not put your hand over the spray tip.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Do not spray without tip guard and trigger guard installed.
D Engage the gun trigger safety when you stop spraying.
D Follow the Pressure Relief Procedure on page 3 if the spray tip clogs and before cleaning,
checking or servicing the equipment.

2

310643

Service
Pressure Relief Procedure

WARNING
PRESSURIZED EQUIPMENT HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. To
reduce the risk of an injury from accidental spray
from the gun, splashing fluid, or moving parts,
follow the Pressure Relief Procedure whenever
you:
D
D
D
D

are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
or install or clean the spray nozzle.

1. Engage gun safety latch.
2. Turn ON/OFF switch to OFF.
3. Unplug power cord.
4. Disengage gun safety latch. Hold metal part of gun
against grounded metal pail and trigger gun into
pail to relieve pressure.
5. Engage gun safety latch.
6. Open any fluid drain valves in system. Leave drain
valve open until ready to dispense again.

Pump Repair Kits
Pump

Repair Kit

248204, 255968

248212

253056

287825

248205, 249057, 249059,
257146

248213

Tools Needed
Vise
12 in. adjustable, open end wrench (2)
Hammer, 20 oz maximum
Small screwdriver
Throat Seal Liquid
Pick or long small screwdriver

Cleaning and Inspecting Parts
1. Clean and inspect parts. Pay particular attention to
the ball seats in the intake valve and piston, which
must have no nicks or wear, and to the inside of
the sleeve and the outside of the piston rod, which
must not be worn or scratched. Replace worn or
damaged parts.

WARNING
COMPONENT RUPTURE HAZARD
Never use sharp or pointed tools to
remove sleeve or other components
which could result in pump rupture and
cause serious bodily injury. If the sleeve cannot be
removed easily, return the sleeve and cylinder to
your Graco distributor for removal.

2. Remove and clean the sleeve when you are
repacking the pump.

310643

3

Service
Repair When Pump Is Off The Sprayer

Fig. 3. Disassemble intake valve. Clean and inspect.
O-ring (227) may require a pick for removal.

Disassembling the pump
Fig. 1. Remove packing nut (202) and throat adjustment spacer (228).
202

227

228

Fig. 3

7570e

Fig. 4. Tap piston rod out of cylinder with a hammer or
flip over and tap piston rod out against a bench.
ti2332a

Fig. 1

7568A

Note: Sleeve may come out
of cylinder with piston rod.
Fig. 2. Unscrew intake valve from cylinder.

Fig. 4

7571a

Fig. 5. Remove piston rod from sleeve, or remove
sleeve from cylinder. Mark IV: Remove sleeve spacer
(230) from sleeve.

Fig. 2

4

7569A

Fig. 5

310643

7572A

Service
Fig. 8. Remove throat packings and glands from cylinder. Discard throat packings and glands.

WARNING
COMPONENT RUPTURE HAZARD
Do not clean or wipe the piston valve
threads. Cleaning the piston valve
threads could destroy the special sealing
patch and cause the piston valve to come loose
during operation, causing pump bursting and
possible serious bodily injury.

Not
used on
248204
253056
255968

Fig. 6. Unscrew piston valve from piston rod. Clean
and inspect parts. The piston has a special thread
locking/sealing patch. Do not remove the patch. The
patch allows four disassembly/assembly procedures
before it is necessary to apply Loctiter to the threads.

7573B

Fig. 8
Assembling the pump

Fig. 6

7576A

Fig. 7. Remove packings and glands from piston rod.
Not
used on
248204
253056
255968

Fig. 7

Fig. 9. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Stack male gland
(204) on piston rod. Alternately stack UHMWPE (208)
and leather (218) packings (note orientation) on piston
rod. Install female gland (217). Install piston wiper
(216) (note orientation) and backup washer (229) on
piston valve (210). The special sealing patch on piston
valve threads is good for four repackings. Use Loctiter
on piston valve threads after four repackings.
Not
used on
248204
253056
255968

210
229
216

ti3940b

Fig. 9

218

204 208

217
7574d

310643

5

Service
Fig. 10. Install ball (206) in piston rod. If Loctiter is applied to piston valve threads, ensure that none gets on
ball.

Fig. 12. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Place male gland
(204) in cylinder. Alternately stack UHMWPE (203) and
leather packings (223) (note orientation). Place female
gland (224) in top of cylinder. Seat packings.

206
224

203

223

Not
used on
248204
253056
255968

204
Fig. 10

7575A

Fig. 11. Tighten piston valve to piston rod as specified:
7573f

Fig. 12
Torque to 27 +/--3 ft-lb
(248204, 253056, 255968,
277069)

Fig. 13. Install seal (201) into packing nut (202). Install
throat adjustment spacer (228) onto packing nut.
Loosely install packing nut into cylinder.

Torque to 55 +/--3 ft-lb
(248205, 249057, 249059,
277070, 257146)

201
202
228

7576A

Fig. 11

6

310643

Fig. 13

7581A

Service
Fig. 14. Grease piston packings.

Fig. 16. Grease top inch or two of piston rod that will
go through the cylinder throat packings.

Fig. 16
ti7578c

Fig. 14

7579A

Fig. 17. Grease o-rings (221) and place on sleeve.
Slide sleeve/piston rod assembly into bottom of cylinder. Replace o-ring (207) if desired.
Note: O-ring (207) is not required for safe pump operation.

CAUTION
Do not slide piston assembly into top of sleeve as
this may damage piston packing.

Fig. 15. Slide piston assembly into bottom of sleeve.

207
221

Fig. 15

7577A
7582A

Fig. 17

310643

7

Service
Fig. 18. Mark IV: Install o-ring (231) on sleeve spacer
(230) and install sleeve spacer on sleeve.
ti7340a

230
231

Fig. 18
Fig. 19. Reassemble intake valve with new o-ring
(227), seat (212) and ball (214). Seat may be flipped
over and used on other side. Clean seat thoroughly.

Fig. 20

7569A

Fig. 21. Torque packing nut (202) down onto adjustment spacer (228) 100 +/--10 in-lb.

214

Remove throat adjustment spacer (228) when pump
packings begin to leak after much use. Then tighten
packing nut down until leakage stops or lessens. This
allows approximately 100 gallons of additional operation before a repacking is required.

212
227

202
228

7570f

Fig. 19

Fig. 20. Install intake valve on cylinder. If a wrench is
used torque as follows:
67 +/--5 ft-lb (Model 248204, 253056, 255968,
277069)
80 +/--5 ft-lb (Model 248205, 249057, 249059,
277070, 257146 )
If a wrench is not used, be sure intake valve is bottomed out against cylinder.

8

310643

Fig. 21

7568A

Service
Repair When Pump Is On The Sprayer

Fig. 2. Push up retaining spring (26).

WARNING
SKIN INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 3.

Fig. 1. Remove intake valve.

26

Fig. 2

ti4258a

Fig. 3. Push out pin (29).
29

Fig. 1

ti4258a

26
ti4258a

Fig. 3

Fig. 4. Disassemble intake valve. Clean and inspect.
O-ring (227) may require a pick for removal.

227

Fig. 4

7570A

310643

9

Service
Fig. 5. Remove piston rod and sleeve.

Fig. 8. Invert piston rod and insert into cylinder to force
out throat packings.

7746A

Fig. 5

Fig. 5. Invert piston rod and sleeve and pound on hard
surface until piston rod comes out of sleeve. Mark IV:
Remove sleeve spacer from sleeve.

ti7339a

Fig. 8

ti4258a

Fig. 9. Insert piston rod into cylinder with pin hole up
and piston valve down. Insert pin into piston rod and
crank shaft.
7572A

Fig. 6
Fig. 7. Remove packing nut (202)

202

7726A

Fig. 7

10

310643

Fig. 9

ti4258a

Service
Fig. 10. Remove piston valve from piston rod with a
wrench.

Fig. 12. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Stack male gland
(204). Alternately stack UHMWPE (203) and leather
(223) packings (note orientation). Install female gland
(224). Install seal (201) and packing nut (202) and
throat adjustment spacer (228).

Not
used on
248204
253056
255968

224

ti4258a

Fig. 10

203

201

223

228
202

Fig. 11. Remove pin and piston rod from cylinder.

204

Fig. 12

7573c

Fig. 13. Remove packings and glands from piston rod.
Fig. 11

Not
used on
248204
253056
255968

ti4258a

Fig. 13

ti3939a

310643

11

Service
Fig. 14. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Stack male gland
(219) on piston rod. Alternately stack UHMWPE (208)
and leather (218) packings (note orientation) on piston
rod. Install female gland (217). Install piston wiper
(216) and backup washer (229) (note orientation) on
piston valve (210). The special sealing patch on piston
valve threads is good for four repackings. Use Loctiter
on piston valve threads after four repackings.

219

217

Fig. 16

ti7578c

CAUTION

Not
used on
248204
253056
255968

216
229
206
218

Fig. 14

Fig. 16. Grease piston packings.

210

208

ti3941a

Do not slide piston assembly into top of sleeve as
this may damage piston packing.
Fig. 17. Slide piston assembly into bottom of sleeve.
Assure V-packing and u-cup are not rolled over or
damaged. Mark IV: Install o-ring (231) on sleeve
spacer (230). Install sleeve spacer on sleeve.
ti7341a

Fig. 10. Install ball (206) in piston rod. If Loctiter is applied to piston valve threads, ensure that none gets on
ball. Install piston valve on piston rod.
Torque as follows:
27 +/--3 ft-lb (Model 248204, 253056, 255968,
277069)
55 +/--3 ft-lb (Model 248205, 249057, 249059,
277070, 257146)

Mark IV

7577b

Fig. 17
Fig. 18. Grease top inch or two of piston rod that will
go through the cylinder throat packings.

206

Fig. 15
12

7575A

Fig. 18
310643

7579A

Service
Fig. 19. Grease o-ring (221) and place on sleeve. Slide
sleeve/piston rod assembly into bottom of cylinder. Replace o-ring (207) if desired.

Fig. 21. Push up retaining spring (26) with screwdriver.

Note: O-ring (207) is not required for safe pump operation.

207
221
Fig. 19

ti4258a

Fig. 21. Torque seal and packing nut (202) down onto
throat adjustment spacer (228) to 100 +/--10 in-lb.
Remove throat adjustment spacer (228) when pump
packings begin to leak after much use. Then tighten
packing nut down until leakage stops or lessens. This
allows approximately 100 gallons of additional operation before a repacking is required.

26

Fig. 21

ti4258a

Fig. 22. Push in pin (29).
29

202
26

228
Fig. 22
Fig. 20

ti4258a

Note: Make sure retaining ring falls into slot.

7726b

310643

13

Service
Fig. 23. Reassemble intake valve with new o-rings
(227) and (230), seat (212) and ball (214). Seat may
be flipped over and used on other side. Clean seat
thoroughly.

Fig. 24. Install intake valve on cylinder. Torque:
70 +/--5 ft-lb (model 248204, 253056, 255968,
277069)
80 +/--5 ft-lb (Model 248205, 249057, 249059,
277070, 257146)

214
212
227

230
Fig. 23

14

7570f

310643

Fig. 24

ti4258a

Service
222
201
202
228

224
223

203

V-Maxt UHWMPE, blue

Leather

204

205
221

Pump 248204

220
206

207
219

208

218

Leather

2

217
216

210

V-Maxt UHWMPE, blue

229

221

214
213

215
212
227

7683d

230

Fig 25

Technical Data
Maximum working pressure . . . . . . . . . . . . . . . 3300 psi
(227 bar, 22.7 MPa)
Fluid inlet size . . . . . . . . . . . . . . . . . . . 1-5/16--12 un(m)

Fluid outlet size
248204, 255968, 277069 . . . . . . . . . . . . . . . . 1/4 npt(f)
248205, 249057, 249059, 253056,
277070, 257146 . . . . . . . . . . . . . . . . . . . . . . . 3/8 npt(f)
Wetted parts . . . . . . . . . . stainless steel, PTFE, leather,
nylon, zinc-plated carbon steel, tungsten carbide,
chrome plating, fluoroelastomer, acetal, polyethylene

310643

15

Parts -- Pump 248204, 277069, 255968
Model 248204, Series A; 277069, Series A; 255968, Series A
Ref
No.

Part No.

Description

201
202
203*

179810
193046
192692

204*
205

15C987

SEAL, throat
NUT, packing
V-PACKING, throat,
V-Maxt UHMWPE, blue
GLAND, male, throat
CYLINDER, pump
Model 248204, 255968
Model 277069
BALL, sst, 0.3125 in.
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
KIT, seat, carbide
includes 214 and 227
VALVE, intake (foot)
Model 248204, 255968
VALVE, intake, Model 277069
BALL, sst, 0.5000 in.
GUIDE, ball
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, male
SLEEVE, cylinder
O-RING, PTFE
ROD, piston
V-PACKING, leather, throat
GLAND, female
PACKING, o-ring
SPACER, throat, nut
WASHER, backup
O-RING, fluoroelastomer (not used
on Lo-boy)

206*
207*
208*

243346
243346
105444
114054
192693

210
212†

239932
239922

213

15C785

195892
214*† 105445
215
192624
216* 118503
217* 178969
218* 178939
219* 196880
220
248209
221* 108526
222
248206
223* 178940
224* 15C988
227*† 107079
228
192714
229* 15C997
230* 118494

201

Qty.
1
1
3

202

221*

228

1
1
1
1
1
3
1
1

222

224*

*223

219*

203*
204*
*208

218*

1
1
1
1
1
2
1
1
2
1
2

217*
216*
229
206*
210
215
205

1
1
1

207*

1

221*

†*214
212†
†*227
213

* These parts are also included in Repair Kit 248212,
which may be purchased separately.
† These parts are also included in Carbide Seat Kit
239922, which may be purchased separately.

220
(Not an O--ring groove)

230*
ti4255a

16

310643

Parts -- Pumps 248205, 249057, 249059, 277070, 257146
Model 248205, Series A; 249057, Series A; 249059, Series A; 277070, Series A; 257146, Series A
Ref No. Part No.

Description

201+ 183171
202
193032
203*+ 193124

PLUG
NUT, packing
V-PACKING
V-Maxt UHMWPE, blue
GLAND, packing, male, throat
CYLINDER, pump
Model 248205, 277070
Model 249057, 249059, 257146
BALL, 0.375 in.
Model 248205, 249057, 277070,
257146, sst
Model 249059, ceramic
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
KIT, SEAT, carbide
includes 214 and 227
Model 248205, 249057, 277070,
257146
Model 249059
HOUSING, intake (foot)
Model 248205,
Model 249059, 249057
Model 277070, 257146
BALL
Model 248205, 249057, 277070,
257146 sst, 0.875 in.
Model 249059, ceramic, 0.750 in.
GUIDE, ball
Model 249059, 249057
Model 248205, 277070, 257146
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, packing, male
SLEEVE, cylinder
Model 248205, 249057, 249059,
277070
Model 257146
PACKING, o-ring
ROD, piston
Model 248205, 277070
Model 249059, 249057, 257146
V-PACKING, leather, throat
GLAND, packing, female
PACKING, o-ring
SPACER, nut
WASHER, backup
O-RING, fluoroelastomer
(not used on 249057, 249059, 257146)

204*+ 15C989
205
243347
196754
206
101947*
116327+
207*+ 156633
208*+ 193125
210
212†

240150

244199
244571
213
15C783
196753
195894
214
102972*†
111453+
215

216*+
217*+
218*+
219*+
220

196967
193027
118504
183185
15E329
183178
248210

257031
221*+ 107098
222
248207
249028
223*+ 183175
224*+ 15C990
227*†+ 108526
228+ C20987
229*+ 15C998
230*+ 118494

Qty.

231

117608

NIPPLE, straight
Model 249057, 249059 (not shown)
ADAPTER, 3/8 npt x 3/8 npsm
Model 249057, 249059, 257146
(not shown)

1

1
1
4

232

162485

1
1

* These parts are also included in Repair Kit 248213, which
may be purchased separately.
† These parts are also included in Carbide Seat Kit 244199,
which may be purchased separately

1

+ These parts are included in Pump Repair Kit 249189.
1
1
1
4

201
202
228

221*

1

224*
1
1
1
1
1

222

*223

203*
204*
*208

1
1
1
1
1
1
1
3
1
1

1
1
3
1
1
1
1
1

218*
217*
216*
229
206*
210

205
215
207*

2

219*

221*

†*214
212†
†*227

220

213

(Not an O--ring groove)
230*

310643

17

Parts -- Pump 253056
Ref
No.

Part No.

201*§ 179810
202
193046
203*§ 192692
204*§ 15C987
205
287876
206* 105444
206§ 119259
207*§ 156593
208*§ 192693
210
287877
212†n 197470
213
287878
214*† 102972
214§n
dard) 1
215
196967
216*§ 118503
217*§ 178969
218*§ 178939
219*§ 196880
220
248209
221*§ 108526
222
249969
223*§ 178940
224*§ 15C988
227*† 108526
§n
228*§ 158776
229*§ 15C997
230
15G494
231*§ 107098

Description

Qty.

SEAL, throat
1
NUT, packing
1
V-PACKING, throat,
3
V-Maxt UHMWPE, blue
GLAND, male, throat
1
CYLINDER, pump
1
BALL, sst, 0.3125 in. (optional)
1
BALL, ceramic, 0.3125 in.
(standard)
1
PACKING, o-ring
1
V-PACKING, piston
3
V-Maxt UHMWPE, blue
VALVE, piston
1
SEAT, carbide
1
HOUSING, intake
1
BALL, sst, 0.875 in. (optional)
1
111453 BALL, ceramic, 0.750 (stan-

222
224*§
*§223

204*§
218*§
*§208
217*§
216*§
229*§

1

221*§

SPACER, throat, nut
WASHER, backup
SPACER, sleeve
O-RING

1
1
1
1

These parts are also included in Carbide Seat Kit
with ceramic ball, 2V071, purchased separately.
18
310643

219*§

203*§

207*§

These parts are also included in Repair Kit with
ceramic ball, 24V063, purchased separately.

221*§

228*§

1
1
1
2
1
1
2
1
2

† These parts are also included in Carbide Seat Kit
with stainless steel ball, 244199, purchased separately.
n

202

GUIDE, ball
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, male
SLEEVE, cylinder
O-RING, PTFE
ROD, pump (MARK IV)
V-PACKING, leather, throat
GLAND, female
PACKING, o-ring

* These parts are also included in Repair Kit with
stainless steel ball, 287825, purchased separately.
§

201*§

206*§
210
215
205

†*§n214

†*§n227

212†n
213

220
(Not an O--ring groove)
230
231*§

ti7338a

Notes

310643

19

Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from
defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended,
or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the
equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained
in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non--Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches,
hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.

ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty
Program”.

TO PLACE AN ORDER, contact your Graco distributor, or call 1--800--690--2894 to identify the nearest distributor.

All written and visual data contained in this document reflect the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original insttructions. This manual contains English. MM 310643

20

Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES P.O. BOX 1441 MINNEAPOLIS, MN 55440--1441 USA
Copyright 2003, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
12/2003, Revised January 2014
310643



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Keywords                        : Displacement Pump; 310643
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2014:02:18 12:46:13-06:00
Create Date                     : 2014:02:04 13:34:16-06:00
Metadata Date                   : 2014:02:18 12:46:13-06:00
Format                          : application/pdf
Title                           : 310643T Displacement Pump, Repair, English
Creator                         : Terri Howard
Description                     : Displacement Pump 310643
Subject                         : Displacement Pump, 310643
Document ID                     : uuid:81a3591f-8017-4cb1-8bdc-fa55af187302
Instance ID                     : uuid:d2cf2974-a5cc-4a07-b1fe-f3809b89c02e
Marked                          : True
Startup Profile                 : Print
Page Count                      : 20
Author                          : Terri Howard

EXIF Metadata provided by EXIF.tools