Graco 310643T Displacement Pump Users Manual Pump, Repair, English

257146 3a177695-9978-4cc8-8c8e-353aa425e8f3 Graco Marine Sanitation System 257146 User Guide |

2015-04-02

: Graco Graco-310643T-Displacement-Pump-Users-Manual-686120 graco-310643t-displacement-pump-users-manual-686120 graco pdf

Open the PDF directly: View PDF .
Page Count: 20

Repair

Displacement Pump 310643T

8016A

3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure

Model 248204, Series A

UltrarMax II and Ultimate Mx II 695 and 795

ASM Zip--Sprayt2700 Plus, 3100 Plus

ASM AllPro Mach 8600 Plus and 11000 Plus

ASM H2700 Plus

Model 255968, Series A

ASM 3600G Plus

Model 248205, Series A

Ultra Max II and Ultimate Mx II 1095 and 1595

Model 249059, Series A

TexSpraytMark V

Model 249057, Series A

TexSpray Mark V

Model 277069, Series A

LineLazertIV 3900, R300

Model 277070, Series A

LineLazertIV 5900

Model 253056, Series A

Mark IV

Model 257146, Series A

Ironman 300E and Ironman 500G

Important Safety instructions

Read all warnings and instructions in this manual.

Save these instructions.

2 310643

Table of Contents

Warnings 2......................................

Service 3.......................................

Technical Data 15................................

Parts, Pump

248204, 255968 16.............................

248205, 249057, 249059, 277070, 257146 17.....

253056 18.....................................

Warranty 20.....................................

WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

DDo not exceed the maximum working pressure temperature rating of the lowest rated system

component. See Technical Data in all equipment manuals.

DUse fluids and solvents compatible with equipment wetted parts. See Technical Data in all equip-

ment manuals. Read manufacturer fluid and solvent warnings.

DCheck equipment daily. Repair or replace worn or damaged parts immediately.

DDo not alter or modify equipment.

DRead all instruction manuals, tags, and labels before operating the equipment.

DUse equipment only for its intended purpose. Call your Graco distributor for information.

DDo not use 1,1,1--trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or

fluids containing such solvents in pressurized aluminum equipment. Such use could result in a

chemical reaction, with the possibility of explosion.

DComply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch or amputate your fingers.

DKeep clear of moving parts.

DDo not operate equipment with protective guards or covers removed.

DPressurized equipment can start without warning. Before checking, moving or servicing equipment,

follow the Pressure Relief Procedure on page 3. Disconnect power cord.

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks or ruptured components will pierce skin. This may look like

just cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

DDo not point the gun at anyone or at any part of the body.

DDo not put your hand over the spray tip.

DDo not stop or deflect leaks with your hand, body, glove or rag.

DDo not spray without tip guard and trigger guard installed.

DEngage the gun trigger safety when you stop spraying.

DFollow the Pressure Relief Procedure on page 3 if the spray tip clogs and before cleaning,

checking or servicing the equipment.

3310643

Service

Pressure Relief Procedure

WARNING

PRESSURIZED EQUIPMENT H

The system pressure must be manually

relieved to prevent the system from

starting or spraying accidentally. To

reduce the risk of an injury from accidental spray

from the gun, splashing fluid, or moving parts,

follow the Pressure Relief Procedure whenever

you:

Dareinstructedtorelievethepressure,

Dstop spraying,

Dcheck or service any of the system equipment,

Dor install or clean the spray nozzle.

1. Engage gun safety latch.

2. Turn ON/OFF switch to OFF.

3. Unplug power cord.

4. Disengage gun safety latch. Hold metal part of gun

against grounded metal pail and trigger gun into

pail to relieve pressure.

5. Engage gun safety latch.

6. Open any fluid drain valves in system. Leave drain

valve open until ready to dispense again.

Pump Repair Kits

Pump Repair Kit

248204, 255968 248212

253056 287825

248205, 249057, 249059,

257146

248213

Tools Needed

Vise

12 in. adjustable, open end wrench (2)

Hammer, 20 oz maximum

Small screwdriver

Throat Seal Liquid

Pick or long small screwdriver

Cleaning and Inspecting Parts

1. Clean and inspect parts. Pay particular attention to

the ball seats in the intake valve and piston, which

must have no nicks or wear, and to the inside of

the sleeve and the outside of the piston rod, which

must not be worn or scratched. Replace worn or

damaged parts.

WARNING

COMPONENT RUPTURE HAZARD

Never use sharp or pointed tools to

remove sleeve or other components

which could result in pump rupture and

cause serious bodily injury. If the sleeve cannot be

removed easily, return the sleeve and cylinder to

your Graco distributor for removal.

2. Remove and clean the sleeve when you are

repacking the pump.

4 310643

Service

Repair When Pump Is Off The Sprayer

Disassembling the pump

Fig. 1. Remove packing nut (202) and throat adjust-

ment spacer (228).

Fig. 1 7568A

228

ti2332a

202

Fig. 2. Unscrew intake valve from cylinder.

Fig. 2 7569A

Fig. 3. Disassemble intake valve. Clean and inspect.

O-ring (227) may require a pick for removal.

Fig. 3

227

7570e

Fig. 4. Tap piston rod out of cylinder with a hammer or

flip over and tap piston rod out against a bench.

Fig. 4 7571a

Note: Sleeve may come out

of cylinder with piston rod.

Fig. 5. Remove piston rod from sleeve, or remove

sleeve from cylinder. Mark IV: Remove sleeve spacer

(230) from sleeve.

Fig. 5 7572A

5310643

Service

WARNING

COMPONENT RUPTURE HAZARD

Do not clean or wipe the piston valve

threads. Cleaning the piston valve

threads could destroy the special sealing

patch and cause the piston valve to come loose

during operation, causing pump bursting and

possible serious bodily injury.

Fig. 6. Unscrew piston valve from piston rod. Clean

and inspect parts. The piston has a special thread

locking/sealing patch. Do not remove the patch. The

patch allows four disassembly/assembly procedures

before it is necessary to apply Loctiterto the threads.

Fig. 6 7576A

Fig. 7. Remove packings and glands from piston rod.

Fig. 7

Not

used on

248204

253056

255968

ti3940b

Fig. 8. Remove throat packings and glands from cylin-

der. Discard throat packings and glands.

Fig. 8 7573B

Not

used on

248204

253056

255968

Assembling the pump

Fig. 9. Soak all leather packings in SAE 30W oil for 1

hour minimum prior to assembly. Stack male gland

(204) on piston rod. Alternately stack UHMWPE (208)

and leather (218) packings (note orientation) on piston

rod. Install female gland (217). Install piston wiper

(216) (note orientation) and backup washer (229) on

piston valve (210). The special sealing patch on piston

valve threads is good for four repackings. Use Loctiter

on piston valve threads after four repackings.

Fig. 9

216

218 208

204

217

210

Not

used on

248204

253056

255968

7574d

229

6 310643

Service

Fig. 10. Install ball (206) in piston rod. If Loctiteris ap-

plied to piston valve threads, ensure that none gets on

ball.

Fig. 10

206

7575A

Fig. 11. Tighten piston valve to piston rod as specified:

Fig. 11

Torque to 27 +/--3 ft-lb

(248204, 253056, 255968,

277069)

Torque to 55 +/--3 ft-lb

(248205, 249057, 249059,

277070, 257146)

7576A

Fig. 12. Soak all leather packings in SAE 30W oil for 1

hour minimum prior to assembly. Place male gland

(204) in cylinder. Alternately stack UHMWPE (203) and

leather packings (223) (note orientation). Place female

gland (224) in top of cylinder. Seat packings.

Fig. 12

203

224

223

204

Not

used on

248204

253056

255968

7573f

Fig. 13. Install seal (201) into packing nut (202). Install

throat adjustment spacer (228) onto packing nut.

Loosely install packing nut into cylinder.

Fig. 13

201

202

7581A

228

7310643

Service

Fig. 14. Grease piston packings.

Fig. 14 ti7578c

CAUTION

Do not slide piston assembly into top of sleeve as

this may damage piston packing.

Fig. 15. Slide piston assembly into bottom of sleeve.

Fig. 15 7577A

Fig. 16. Grease top inch or two of piston rod that will

go through the cylinder throat packings.

7579A

Fig. 16

Fig. 17. Grease o-rings (221) and place on sleeve.

Slide sleeve/piston rod assembly into bottom of cylind-

er. Replace o-ring (207) if desired.

Note: O-ring (207) is not required for safe pump opera-

tion.

Fig. 17 7582A

221

207

8 310643

Service

Fig. 18. Mark IV: Install o-ring (231) on sleeve spacer

(230) and install sleeve spacer on sleeve.

Fig. 18

ti7340a

231

230

Fig. 19. Reassemble intake valve with new o-ring

(227), seat (212) and ball (214). Seat may be flipped

over and used on other side. Clean seat thoroughly.

Fig. 19

227

7570f

212

214

Fig. 20. Install intake valve on cylinder. If a wrench is

used torque as follows:

67 +/--5 ft-lb (Model 248204, 253056, 255968,

277069)

80 +/--5 ft-lb (Model 248205, 249057, 249059,

277070, 257146 )

If a wrench is not used, be sure intake valve is bot-

tomed out against cylinder.

Fig. 20 7569A

Fig. 21. Torque packing nut (202) down onto adjust-

ment spacer (228) 100 +/--10 in-lb.

Remove throat adjustment spacer (228) when pump

packings begin to leak after much use. Then tighten

packing nut down until leakage stops or lessens. This

allows approximately 100 gallons of additional opera-

tion before a repacking is required.

Fig. 21

202

228

7568A

9310643

Service

Repair When Pump Is On The Sprayer

WARNING

SKIN INJECTION HAZARD

To reduce the risk of serious injury,

whenever you are instructed to relieve

pressure, follow the Pressure Relief

Procedure on page 3.

Fig. 1. Remove intake valve.

Fig. 1 ti4258a

Fig. 2. Push up retaining spring (26).

Fig. 2 26 ti4258a

Fig. 3. Push out pin (29).

Fig. 3

ti4258a

Fig. 4. Disassemble intake valve. Clean and inspect.

O-ring (227) may require a pick for removal.

Fig. 4 7570A

227

10 310643

Service

Fig. 5. Remove piston rod and sleeve.

7746A

Fig. 5

Fig. 5. Invert piston rod and sleeve and pound on hard

surface until piston rod comes out of sleeve. Mark IV:

Remove sleeve spacer from sleeve.

Fig. 6 7572A

ti7339a

Fig. 7. Remove packing nut (202)

7726A

Fig. 7

202

Fig. 8. Invert piston rod and insert into cylinder to force

out throat packings.

Fig. 8 ti4258a

Fig. 9. Insert piston rod into cylinder with pin hole up

and piston valve down. Insert pin into piston rod and

crank shaft.

Fig. 9 ti4258a

11310643

Service

Fig. 10. Remove piston valve from piston rod with a

wrench.

Fig. 10 ti4258a

Fig. 11. Remove pin and piston rod from cylinder.

Fig. 11 ti4258a

Fig. 12. Soak all leather packings in SAE 30W oil for 1

hour minimum prior to assembly. Stack male gland

(204). Alternately stack UHMWPE (203) and leather

(223) packings (note orientation). Install female gland

(224). Install seal (201) and packing nut (202) and

throat adjustment spacer (228).

Fig. 12

201

228

203

224

223

204

202

Not

used on

248204

253056

255968

7573c

Fig. 13. Remove packings and glands from piston rod.

Fig. 13

Not

used on

248204

253056

255968

ti3939a

12 310643

Service

Fig. 14. Soak all leather packings in SAE 30W oil for 1

hour minimum prior to assembly. Stack male gland

(219) on piston rod. Alternately stack UHMWPE (208)

and leather (218) packings (note orientation) on piston

rod. Install female gland (217). Install piston wiper

(216) and backup washer (229) (note orientation) on

piston valve (210). The special sealing patch on piston

valve threads is good for four repackings. Use Loctiter

on piston valve threads after four repackings.

Fig. 14

210

218

206

208

219 217

Not

used on

248204

253056

255968

ti3941a

229

216

Fig. 10. Install ball (206) in piston rod. If Loctiteris ap-

plied to piston valve threads, ensure that none gets on

ball. Install piston valve on piston rod.

Torque as follows:

27 +/--3 ft-lb (Model 248204, 253056, 255968,

277069)

55 +/--3 ft-lb (Model 248205, 249057, 249059,

277070, 257146)

Fig. 15

206

7575A

Fig. 16. Grease piston packings.

Fig. 16 ti7578c

UTION

Do not slide piston assembly into top of sleeve as

this may damage piston packing.

Fig. 17. Slide piston assembly into bottom of sleeve.

Assure V-packing and u-cup are not rolled over or

damaged. Mark IV: Install o-ring (231) on sleeve

spacer (230). Install sleeve spacer on sleeve.

Fig. 17

7577b

ti7341a

Mark IV

Fig. 18. Grease top inch or two of piston rod that will

go through the cylinder throat packings.

7579A

Fig. 18

13310643

Service

Fig. 19. Grease o-ring (221) and place on sleeve. Slide

sleeve/piston rod assembly into bottom of cylinder. Re-

place o-ring (207) if desired.

Note: O-ring (207) is not required for safe pump opera-

tion.

Fig. 19

207

221

ti4258a

Fig. 21. Torque seal and packing nut (202) down onto

throat adjustment spacer (228) to 100 +/--10 in-lb.

Remove throat adjustment spacer (228) when pump

packings begin to leak after much use. Then tighten

packing nut down until leakage stops or lessens. This

allows approximately 100 gallons of additional opera-

tion before a repacking is required.

Fig. 20

202

7726b

228

Fig. 21. Push up retaining spring (26) with screwdriver.

Fig. 21 26 ti4258a

Fig. 22. Push in pin (29).

Fig. 22 Note: Make sure retaining ring falls into slot.

ti4258a

14 310643

Service

Fig. 23. Reassemble intake valve with new o-rings

(227) and (230), seat (212) and ball (214). Seat may

be flipped over and used on other side. Clean seat

thoroughly.

Fig. 23

227

7570f

230

212

214

Fig. 24. Install intake valve on cylinder. Torque:

70 +/--5 ft-lb (model 248204, 253056, 255968,

277069)

80 +/--5 ft-lb (Model 248205, 249057, 249059,

277070, 257146)

Fig. 24 ti4258a

15310643

Service

Fig 25

223 203

218

V-MaxtUHWMPE, blue

208

217

213

214

204

221

224

205

219

215

212

227

222

202

221

216

206

210

Leather

201

220

228

207

V-MaxtUHWMPE, blue

Pump 248204

7683d

229

230

Technical Data

Maximum working pressure 3300 psi...............

(227 bar, 22.7 MPa)

Fluid inlet size 1-5/16--12 un(m)...................

Fluid outlet size

248204, 255968, 277069 1/4 npt(f)................

248205, 249057, 249059, 253056,

277070, 257146 3/8 npt(f).......................

Wetted parts stainless steel, PTFE, leather,..........

nylon, zinc-plated carbon steel, tungsten carbide,

chrome plating, fluoroelastomer, acetal, polyethylene

16 310643

Parts -- Pump 248204, 277069, 255968

Model 248204, Series A; 277069, Series A; 255968, Series A

Ref

No. Part No. Description Qty.

201 179810 SEAL, throat 1

202 193046 NUT, packing 1

203* 192692 V-PACKING, throat, 3

V-MaxtUHMWPE, blue

204* 15C987 GLAND, male, throat 1

205 CYLINDER, pump

243346 Model 248204, 255968 1

243346 Model 277069 1

206* 105444 BALL, sst, 0.3125 in. 1

207* 114054 PACKING, o-ring 1

208* 192693 V-PACKING, piston 3

V-MaxtUHMWPE, blue

210 239932 VALVE, piston 1

212† 239922 KIT, seat, carbide 1

includes 214 and 227

213 15C785 VALVE, intake (foot) 1

Model 248204, 255968

195892 VALVE, intake, Model 277069

214*† 105445 BALL, sst, 0.5000 in. 1

215 192624 GUIDE, ball 1

216* 118503 WIPER, piston 1

217* 178969 GLAND, female, piston 1

218* 178939 V-PACKING, leather, piston 2

219* 196880 GLAND, male 1

220 248209 SLEEVE, cylinder 1

221* 108526 O-RING, PTFE 2

222 248206 ROD, piston 1

223* 178940 V-PACKING, leather, throat 2

224* 15C988 GLAND, female

227*† 107079 PACKING, o-ring 1

228 192714 SPACER, throat, nut 1

229* 15C997 WASHER, backup 1

230* 118494 O-RING, fluoroelastomer (not used

on Lo-boy) 1

* These parts are also included in Repair Kit 248212,

which may be purchased separately.

†These parts are also included in Carbide Seat Kit

239922, which may be purchased separately.

*223

216*

201

202

224*

203*

204*

205

221*

220

222

206*

219*

218*

217*

210

215

212

†

213

†*214

*208

221*

207* †*227

228

ti4255a

229

230*

(Not an O--ring groove)

17310643

Parts -- Pumps 248205, 249057, 249059, 277070, 257146

Model 248205, Series A; 249057, Series A; 249059, Series A; 277070, Series A; 257146, Series A

Ref No.Part No. Description Qty.

201+ 183171 PLUG 1

202 193032 NUT, packing 1

203*+ 193124 V-PACKING 4

V-MaxtUHMWPE, blue

204*+ 15C989 GLAND, packing, male, throat 1

205 CYLINDER, pump 1

243347 Model 248205, 277070

196754 Model 249057, 249059, 257146

206 BALL, 0.375 in.

101947* Model 248205, 249057, 277070,

257146, sst 1

116327+ Model 249059, ceramic 1

207*+ 156633 PACKING, o-ring 1

208*+ 193125 V-PACKING, piston 4

V-MaxtUHMWPE, blue

210 240150 VALVE, piston 1

212† KIT, SEAT, carbide

includes 214 and 227

244199 Model 248205, 249057, 277070,

257146 1

244571 Model 249059 1

213 HOUSING, intake (foot)

15C783 Model 248205, 1

196753 Model 249059, 249057 1

195894 Model 277070, 257146 1

214 BALL

102972*† Model 248205, 249057, 277070, 1

257146 sst, 0.875 in.

111453+ Model 249059, ceramic, 0.750 in. 1

215 GUIDE, ball 1

196967 Model 249059, 249057 1

193027 Model 248205, 277070, 257146 1

216*+ 118504 WIPER, piston 1

217*+ 183185 GLAND, female, piston 1

218*+ 15E329 V-PACKING, leather, piston 3

219*+ 183178 GLAND, packing, male 1

220 SLEEVE, cylinder 1

248210 Model 248205, 249057, 249059,

277070

257031 Model 257146

221*+ 107098 PACKING, o-ring 2

222 ROD, piston

248207 Model 248205, 277070 1

249028 Model 249059, 249057, 257146 1

223*+ 183175 V-PACKING, leather, throat 3

224*+ 15C990 GLAND, packing, female 1

227*†+ 108526 PACKING, o-ring 1

228+ C20987 SPACER, nut 1

229*+ 15C998 WASHER, backup 1

230*+ 118494 O-RING, fluoroelastomer 1

(not used on 249057, 249059, 257146)

231 117608 NIPPLE, straight 1

Model 249057, 249059 (not shown)

232 162485 ADAPTER, 3/8 npt x 3/8 npsm 1

Model 249057, 249059, 257146

(not shown)

* These parts are also included in Repair Kit 248213, which

may be purchased separately.

†These parts are also included in Carbide Seat Kit 244199,

which may be purchased separately

+ These parts are included in Pump Repair Kit 249189.

*223

216*

201

202

224*

203*

204*

205

221*

220

222

206*

219*

218*

217*

210

215

212†

213

†*214

*208

221*

207*

†*227

228

229

230*

(Not an O--ring groove)

18 310643

Parts -- Pump 253056

Ref

No. Part No. Description Qty.

201*§179810 SEAL, throat 1

202 193046 NUT, packing 1

203*§192692 V-PACKING, throat, 3

V-MaxtUHMWPE, blue

204*§15C987 GLAND, male, throat 1

205 287876 CYLINDER, pump 1

206* 105444 BALL, sst, 0.3125 in. (optional) 1

206§119259 BALL, ceramic, 0.3125 in.

(standard) 1

207*§156593 PACKING, o-ring 1

208*§192693 V-PACKING, piston 3

V-MaxtUHMWPE, blue

210 287877 VALVE, piston 1

212†n197470 SEAT, carbide 1

213 287878 HOUSING, intake 1

214*† 102972 BALL, sst, 0.875 in. (optional) 1

214§n 111453 BALL, ceramic, 0.750 (stan-

dard) 1

215 196967 GUIDE, ball 1

216*§118503 WIPER, piston 1

217*§178969 GLAND, female, piston 1

218*§178939 V-PACKING, leather, piston 2

219*§196880 GLAND, male 1

220 248209 SLEEVE, cylinder 1

221*§108526 O-RING, PTFE 2

222 249969 ROD, pump (MARK IV) 1

223*§178940 V-PACKING, leather, throat 2

224*§15C988 GLAND, female

227*† 108526 PACKING, o-ring 1

§n

228*§158776 SPACER, throat, nut 1

229*§15C997 WASHER, backup 1

230 15G494 SPACER, sleeve 1

231*§107098 O-RING 1

* These parts are also included in Repair Kit with

stainless steel ball, 287825, purchased separately.

§These parts are also included in Repair Kit with

ceramic ball, 24V063, purchased separately.

†These parts are also included in Carbide Seat Kit

with stainless steel ball, 244199, purchased sepa-

rately.

nThese parts are also included in Carbide Seat Kit

with ceramic ball, 2V071, purchased separately.

*§223

216*

201*§

202

224*§

203*§

204*§

205

221*§

220

222

206*

219*§

218*

217*§

210

215

212†

213

†*§n214

*§208

221*§

207*§

†*§n227

228*§

ti7338a

229*§

230

231*§

(Not an O--ring groove)

19310643

Notes

20 310643

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from

defects in materialand workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended,

or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the

equipmentdetermined by Graco to be defective. This warranty applies only when the equipmentis installed, operated and maintained

in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by

faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-

stitution of non--Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of

Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,

installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for

verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The

equipmentwill be returned to the original purchaser transportation prepaid. If inspection of the equipment does notdisclose any defect

in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and

transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT

NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other

remedy (including, but not limited to, incidentalor consequential damages for lost profits,lost sales,injury to person or property, or any

other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the

date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD

BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches,

hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in mak-

ing any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment

hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,

breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings

entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-

sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires

exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.

ADDITIONAL WARRANTY COVERAGE

Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty

Program”.

TO PLACE AN ORDER, contact your Graco distributor, or call 1--800--690--2894 to identify the nearest distributor.

All written and visual data contained in this document reflect the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

For patent information, see www.graco.com/patents.

Original insttructions. This manual contains English. MM 310643

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES P.O. BOX 1441 MINNEAPOLIS, MN 55440--1441 USA

www.graco.com

12/2003, Revised January 2014

Graco 310643T Displacement Pump Users Manual Pump, Repair, English

257146 3a177695-9978-4cc8-8c8e-353aa425e8f3 Graco Marine Sanitation System 257146 User Guide |

Navigation menu

Versions of this User Manual:

Views

Navigation