Grandex PS440-01 Temperature/Humidity Sensor User Manual CA 210 V1 1 GRANDEX 070605

Download:
Mirror Download [FCC.gov]
Document ID	3097081
Application ID	Xu0BBo1dD26PmyHrU9jhRA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.33kB (291590 bits)
Date Submitted	2016-08-12 00:00:00
Date Available	2016-08-12 00:00:00
Creation Date	2016-07-15 18:13:40
Producing Software	Microsoft® Word 2010
Document Lastmod	2016-07-15 18:13:40
Document Title	CA-210 V1.1_GRANDEX_070605
Document Creator	Microsoft® Word 2010
Document Author:	Picheng

Installation Guide
Overview & Operation
Link PS440 to the Controller
❷
Home Automation
Temperature/Humidity Sensor
PS440
❶
The PS440 is a smart, temperature and humidity, sensor which sends an
alert to the PS Controller via RF signaling when there is a pre-defined
change in the temperature or humidity, for the controller to update the
temperature and humidity display in the PS App. Base on the
temperature/humidity change, the controller can also take actions on other
PS devices, e.g. PS switch/power outlets, automatically according to the
pre-programmed rule set.
Download and install the latest PS App to your mobile device, and refer to
the walk through instructions from PS App’s to add your PS440 sensor to the
Controller. The main steps are:
 Use the PS App, set the Controller into the scan mode.
 Use PS440 sensor’s reset pin to set it to scan mode.
 The pairing process between the Controller and PS440 sensor will now
take place.
 The PS App will show the new device, PS440 is added.
1. Battery Compartment
 Install the battery (CR2450)
2. Reset Pin/LED
Reset Pin
 Insert a small pin (e.g. paper clip) to set the PS440 to scan mode
 Insert a small pin (e.g. paper clip) and hold for 5 seconds to reset
PS440 to factory default setting
LED
 Orange – Flashing => PS440 is in scan mode
 Orange – Steady for 2 seconds => Indicate PS440 reset is finished
FCC Statement
Installation
1. Choose a location where you want to detect the temperature and
humidity in your home.
2. Open the battery compartment, remove the battery’s insulator, and
then close the battery compartment
3. Peel off the tape backing from the Sensor, and mount them onto the
chosen location from step 1.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
Language                        : zh-TW
Tagged PDF                      : Yes
Title                           : CA-210 V1.1_GRANDEX_070605
Author                          : Picheng
Subject                         : CA-210 V1.1_GRANDEX_070605
Creator                         : Microsoft® Word 2010
Create Date                     : 2016:07:15 18:13:40+08:00
Modify Date                     : 2016:07:15 18:13:40+08:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools