Grandstream Networks GXV3615WPI-HD IP CAMERA User Manual

Grandstream Networks, Inc. IP CAMERA

User Manual

GXV3615WPI_HD 方型高清摄像机 用户手册 软件版本：1.0.2.58
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 2 of 30 Grandstream Networks, Inc. 02/10/12 Safety Instructions These instructions are intended to assist users with the operation of the GXV3615WPI_HD and also to instruct on how to avoid dangerous situations or damage to the device. Warnings: Serious injury or death may be caused if any of the warnings below are neglected. Cautions: Injury or damage to the equipment may occur if any of the following caution messages are neglected. Warnings Follow these safeguards to prevent serious injury or death. Cautions Follow these precautions to prevent potential injury or material damage. Warnings: Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with DC 12V according to the IEC60950-1 standard. Please refer to the technical specifications for more details. Do not use a third-party power adapter or power cord When the device is installed on the wall or ceiling, make sure that it is firmly attached. Notice： Make sure that the power supply voltage is correct before using the camera. Do not drop the device or expose it to physical shock. Do not expose the device to temperatures outside the range of -10 oC to +60oC when the device is in operation. Do not expose the device to damp/wet conditions or high electromagnetism radiation. To avoid heat accumulation, make sure that your operating environment has proper ventilation. Do not attempt to open, disassemble, or modify the device A few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly according to their average life time. The average life time varies from the differences between operating environments and usage history. Regular maintenance checks are recommended for all users. Please contact your dealer for more details.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 3 of 30 Grandstream Networks, Inc. 02/10/12 Contents Welcome ......................................................................................................................................................... 4 Package Contents ............................................................................................................................................ 5 Product Overview ........................................................................................................................................... 5 GXV3615WPI_HD Series Overview ..................................................................................................... 5 GXV3615WPI_HD Series Front Panel ................................................................................................... 6 GXV3615WPI_HD Series Back Panel ................................................................................................... 6 GXV3615WPI_HD Series Sample Connection Diagram ....................................................................... 6 GXV3615WPI_HD Series Key Features ................................................................................................ 7 GXV3615WPI_HD Lens Specification .................................................................................................. 8 Minimum Recommended System Requirement ..................................................................................... 9 Connect your GXV3615WPI_HD Series ............................................................................................... 9 Configuring the GXV3615WPI_HD Series via Web Browser ............................................................. 10 Access GXV3615WPI_HD Series Web Configuration Menu .............................................................. 10 Connect the Camera to DHCP server. ................................................................................................... 10 Connect to the Camera using Static IP. ................................................................................................. 11 GXV3615WPI_HD Series Home Web Page ........................................................................................ 12 GXV3615WPI_HD Series System Page ............................................................................................... 13 GXV3615WPI_HD Series Video & Audio Page .................................................................................. 14 GXV3615WPI_HD Series Networking Page – Assign an IP to GXV3615WPI_HD ........................... 15 GXV3615WPI_HD And GXV3615W_HD Wifi Page – This page is only available for GXV3615W_HD and GXV3615WPI_HD ........................................................................................ 16 GXV3615WPI_HD Series DDNS Page ............................................................................................... 16 GXV3615WPI_HD Series SIP Page ..................................................................................................... 17 GXV3615WPI_HD Series Status Page ................................................................................................. 19 GXV3615WPI_HD Series User Management Page ............................................................................. 20 GXV3615WPI_HD Series Maintenance Page ...................................................................................... 20 GXV3615WPI_HD Series SMTP Page ................................................................................................ 21 GXV3615WPI_HD Series FTP Page .................................................................................................... 22 GXV3615WPI_HD Series Motion Detection Page .............................................................................. 22 GXV3615WPI_HD Series System Log ................................................................................................ 24 FAQ ............................................................................................................................................................... 25 Compliance ................................................................................................................................................... 29
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 4 of 30 Grandstream Networks, Inc. 02/10/12 Welcome The GXV3615WPI_HD Series is a next generation IP camera for remote monitoring and surveillance over your LAN or internet. The GXV3615WPI_HD Series combines best in class IP video technology and SIP protocols for a robust IP surveillance solution. The product features H.264 video streams with up to 30 frames per second in full D1, delivering rich image clarity at rapid transmission rates. Integrated SIP can pass alarms to the PSTN, mobile phones, SIP IP phones, SIP videophones and enables 2-way VoIP communication. The GXV3615WPI_HD series also support PoE(GXV3615WPI_HD and GXV3615P_HD) or WIFI (GXV3615WPI_HD and GXV3615W_HD). The GXV3615WPI_HD Series ensures ease of use, integration and deployment with a multilingual graphical user interface. The GXV3615WPI_HD Series can be quickly installed and connected to your network and accessed from anywhere over the internet. Grandstream’s flexible video management software enables users to monitor multiple environments in one easy to use application. The intuitive web interface lets users easily access, manage, view and record live video streams from the device. The GXV3615WPI_HD Series is a powerful solution for small to medium sized offices, homes and storage facilities looking to safeguard their valuables.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 5 of 30 Grandstream Networks, Inc. 02/10/12 Package Contents Items in the package:  GXV3615WPI_HD /GXV3615W_HD / GXV3615P_HD/ GXV3615_HD IP Camera  12V DC power Adapter  Mount Stand  Ethernet Cable  Quick installation guide Product Overview GXV3615WPI_HD series includes 4 models: GXV3615WPI_HD /GXV3615W_HD / GXV3615P_HD/ GXV3615_HD GXV3615WPI_HD Series Overview
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 6 of 30 Grandstream Networks, Inc. 02/10/12 GXV3615WPI_HD Series Front Panel Speaker– GXV3615WPI_HD built-in speaker Status Indicator – Red when power up / Green when ready. Microphone– GXV3615WPI_HD built-in microphone GXV3615WPI_HD Series Back Panel NETWORK – 10/100 Switch LAN port for connecting to Ethernet. The indicator will be steady for connection and flashing for network activity. DC 12V – 12V DC power jack; UL Certified. RESET – Press the Reset button for 6 seconds to Mounting Socket – This is used for mounting GXV3615WPI_HD GXV3615WPI_HD Series Sample Connection Diagram
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 7 of 30 Grandstream Networks, Inc. 02/10/12 GXV3615WPI_HD Series Key Features The table below lists the key features the GXV3615WPI_HD Series. Features GXV3615WPI_HD GXV3615W_HD GXV3615P_HD GXV3615_HD Image Sensor 1/3”, CMOS, 1600H x 1200V pixel resolution, exceptionally low noise levels and low-light sensitivity achieve superior resolution at CCD image quality Lens Type 1/3”, M12, f=3.60mm, F1.5, FOV=64° Minimum Illumination 0.05Lux Video Compression H.264, JPEG, Motion JPEG Max Video Resolution 1600x1200, 1280x960, 1280x720, 1024x768, 800x592, 800x480 640x480, 640x368, 480x368, 480x272, 320x240, 320x176, 256x192, 256x144, 160x112 Pixel Dynamic Range 82dB Max Frame Rate in Max 30fps Video Bit Rate 16 Kbps – 2 Mbps Audio Input Built-in Microphone Audio Output Built-in Speaker Audio Compression G.711, G726 Embedded Analytics Motion Detection (up to 16 target areas), video loss (pending) Video Management System ONVIF compliant, HTTP API for advanced integration Pre-/post alarm buffer 24MB
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 8 of 30 Grandstream Networks, Inc. 02/10/12 Snapshots Trigger upon events, send via email/FTP Network Protocol TCP/UDP/IP, RTP/RTCP, RTSP, DHCP, DDNS, HTTP, HTTPS, SMTP, FTP, NTP Network Port 10M/100M auto-sensing, RJ45 Multi-streaming-rate for Preview and Recording Yes Security HTTPS, password Power over Ethernet (PoE) Standard,IEEE802.3afClass 3 N/A Standard, IEEE 802.3af Class 3 N/A Wi-Fi (802.11b/g/n) N/A Yes N/A N/A SIP/VoIP Support Yes, Voice & Video-over-IP Weight 0.128kg Temperature / Humidity 0°C – 45°C (32°F–113°F) Humidity 10–90% RH (non–condensing) Power Output: 12VDC/0.5A; Input: 100–240VAC, 50–60Hz Compliance FCC, CE, C-tick,RF,ERC70-03,15.105 Please see page 29 for compliance detail. GXV3615WPI_HD Lens Specification Parameters GXV3615WPI_HD /GXV3615W_HD / GXV3615P_HD/ GXV3615_HD Lens Mount M12 Lens Format 1/3” Focal Length 4.2 mm Aperture (D/f’) 1.5 View Angle 64 Size (Diameter x Length 1 x Length 2) 14x12.91mm
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 9 of 30 Grandstream Networks, Inc. 02/10/12 Installation Guide Minimum Recommended System Requirement  Windows 2000 Server Professional, Windows XP, Windows Vista.  CPU: Intel Pentium 4 or higher, 2 GHz.  RAM: 1 GB (4 GB recommended for larger systems).  Support for DirectX 8.0 and above. . Connect your GXV3615WPI_HD Series Using the Power adapter as power supply  Connect an RJ-45 cable to the NETWORK port of the GXV3615WPI_HD.  Connect the other end of the RJ-45 cable to your network or PC.  Connect the power supply to the DC 12V power jack on the back of the GXV3615WPI_HD. Using PoE as power supply: (Not applicable on GXV3615W_HD and GXV3615_HD)  Connect an RJ-45 to the NETWORK port of GXV3615WPI_HD. NOTE: If you are going to connect the device to a hub/switch/router, please use a straight-through cable. A cross over cable should be used if you are going to connect the device directly to a PC.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 10 of 30 Grandstream Networks, Inc. 02/10/12 Configuring the GXV3615WPI_HD Series via Web Browser The GXV3615WPI_HD’s embedded Web server responds to HTTP/HTTPS GET/POST requests. Embedded HTML pages allow you to configure your IP camera through Microsoft Internet Explorer. Access GXV3615WPI_HD Series Web Configuration Menu Connect the Camera to DHCP server. 1. Navigate your browser to: http://www.grandstream.com/support/gxv_series_surveillance/general/resources/gs_search.zip 2. Run the Grandstream GS_Search tool, that you just downloaded. 3. Click on button in order to begin device detection 4. The detected devices will appear in the Output field 5. Start Internet Explorer on your computer. 6. Enter device IP in the address bar of the browser. 7. Enter the administrator user name and password to access the Web Configuration Interface 8. The default user name and password are both set to admin. 9. IE will indicate that “This website wants to install the following add-on: ‘GSViewerX.cab’ from ‘Grandstream Networks Inc’.” Install this add-on by following the instructions in IE. 10. You will see the home page.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 11 of 30 Grandstream Networks, Inc. 02/10/12 Connect to the Camera using Static IP. If the camera does not get response from DHCP server after 3 minutes, it can be accessed by the default IP 192.168.1.168. 1. Connect your PC to the same network as the GXV3615WPI_HD. 2. Configure the IP address of your PC to: 192.168.1.XXX (1<XXX<255) and configure the subnet mask to 255.255.255.0. 3. Make sure that the device is turned on and connected to the network. 4. Start Internet Explorer on your computer. 5. Enter 192.168.1.168 in the address bar of the browser. 6. Enter the administrator user name and password to access the Web Configuration Interface 7. The default user name and password are both set to admin. 8. IE will indicate that “This website wants to install the following add-on: ‘GSViewerX.cab’ from ‘Grandstream Networks Inc’.” Install this add-on by following the instructions in IE. 9. You will see the home page.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 12 of 30 Grandstream Networks, Inc. 02/10/12 GXV3615WPI_HD Series Home Web Page Figure1: Home web page of GXV3615WPI_HD Items on GXV3615WPI_HD Home Page 1 Control Console PTZ Console controller. PTZ device needs to be connected. 2 ZOOM NOTE: GXV3615WPI_HD does not support zoom 3 FOCUS Adjusts the focus of images. 4 APERTURE Adjusts the aperture of images 5 SPEED Adjusts the rotation speed of the console. 6 View Size Resize the image to fit into the window panel in the home scream. 7 BRIGHTNESS Adjusts the image brightness. 8 CONTRAST Adjusts the image contrast. 9 SATURATION Adjusts the image saturation. 10 Language Allow to switch between English and Chinese 11 CONFIGURATION MENU Click this option to enter the GXV3615WPI_HD setting page 12 Default Click this option to reset the video brightness, contrast, and saturation to their factory default configuration. 13 Play Plays/Stops the video. 14 Capture Captures the image displayed and saves it to C:\GS_Capture (default directory).
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 13 of 30 Grandstream Networks, Inc. 02/10/12 15 Record Records the video and saves it to C:\GS_Record (default directory). 16 Sound Off/On Toggles the sound On or Off. 17 Talk Establishes two-way audio. 18 Playback Replays the saved video. 19 Config Configures the Save Location for captured images and recorded videos. 20 Motion Detection If the motion detection alarm is triggered, the indicator will flash red. Click on the indicator to turn off the alarm. GXV3615WPI_HD Series System Page This page allows you to configure the system settings on GXV3615WPI_HD. Current System Time - displays the current date and time (24h clock). Set the System Time Update via NTP Server - the camera will obtain the time from an NTP server Specify the NTP server's IP address or host name. And you can select your time zone from the drop-down list or define your own time zone setting. NOTE: If using a host name for the NTP server, a DNS server must be configured under Basic Settings -> Networking. Synchronize with Local Computer - sets the time from the clock on your computer. Set the Time Manually - this option allows you to manually set the time and date. OSD Date Format - set the format of date on OSD Device Name Setting -This field lets you configure the name of the GXV3615WPI_HD, which helps GSurf and GS_NVR to indentify the device when using GS_Search to search all the
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 14 of 30 Grandstream Networks, Inc. 02/10/12 Grandstream network cameras or digit video cameras in the same subnet. GXV3615WPI_HD Series Video & Audio Page On Screen Display (OSD) Settings OSD Time/ Text – The time stamp and channel name displayed on the screen. Video Settings Preferred Video Codec – The GXV3615WPI_HD supports the H.264 video codec. Resolution – The higher the resolution is, the better the video quality is, and higher bandwidth is required. Low ----------------------- High Resolution QCIF CIF 2CIF D1 Bit Rate – The number of bits that are conveyed or processed per unit of time. Maximum Frame Rate – The video frame rate is adjustable based on network conditions. Increasing the frame rate will increase the amount of data significantly therefore consuming more bandwidth. Video will be impaired due to packet loss when there is insufficient bandwidth. Bit Rate Control – Variable Bit rate (VBR) and Constant Bit Rate (CBR). Variable Bit Rate - If VBR is selected, the codec varies the amount of output data per time segment. VBR produces a better quality-to-space ratio. The bits available are used to enable more flexibly and encode sound or video data more accurately, with fewer bits used in less demanding passages and more bits used in difficult-to-encode passages. Constant Bit Rate - If CBR is selected, the codec’s output data is constant regardless of the input data. The output bit rate is defined in “Bit rate”. CBR is useful for streaming multimedia content on limited capacity channels. It is easier to calculate required bandwidth as well as the required storage space using CBR. I-frame Interval – While streaming video over a network, compression technologies are used
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 15 of 30 Grandstream Networks, Inc. 02/10/12 to show the incremental difference between each frame. I-frames are used to help keep the video looking normal. When intervals are shorter, the video quality is higher but uses more bandwidth. NOTE: The users might need to configure the Primary Stream and Secondary Stream properly. Sometimes, the user might like to watch the live video stream from the web GUI in low resolution mode while recording a copy via GSurf/GS_NVR in high resolution due to the limitation of internet bandwidth. In this case, for example, primary stream can be configured to have better resolution, and then the users can use primary stream to record while watching secondary video streams. Audio Settings Preferred Audio Codec – The GXV3615WPI_HD supports up to 3 different Vocoder types, a-law (PCMA), u-law (PCMU) and G.726. The audio can also be turned off by switching the setting to “Disabled” Audio Compression – Audio compression is a form of data compression designed to reduce the size of audio files. Usually, the higher the audio compression is, the better the audio quality is. Microphone Volumne – Adjust the volume of build-in microphone. Speaker Volumne – Adjust the volume of build-in speaker. GXV3615WPI_HD Series Networking Page – Assign an IP to GXV3615WPI_HD GXV3615WPI_HD supports IP version 4. The IP address can set automatically via DHCP, or a static IP address can be set manually. To make GXV3615WPI_HDwork properly, the user needs to set the DNS configuration properly. For security purposes, the user can also assign the GXV3615WPI_HD an HTTP Port other than 80. IP Address Configuration The GXV3615WPI_HD operates in two modes: Dynamically Assigned via DHCP – all the field values for the Static IP mode are not used. The GXV3615WPI_HD acquires its IP address from the first DHCP server it discovers on its LAN. Statically Configured as – configures all of the following fields: IP address, Subnet Mask, Default Gateway IP address, DNS Server 1 (primary), DNS Server 2 (secondary). These
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 16 of 30 Grandstream Networks, Inc. 02/10/12 fields are set to zero by default. Static IP addresses are recommended for the GXV3615WPI_HD DNS Configuration There are two methods of DNS configuration on the GXV3615WPI_HD: 1. The GXV3615WPI_HD can obtain the DNS server automatically 2. Users can configure their own preferred DNS server HTTP Port The GXV3615WPI_HD supports user configured http ports. If the HTTP port is changed, the port number is needed to access the web GUI, for instance: http://192.168.1.168:8080. NOTE: If the HTTP Port is 80, when you add this device to GSurf or GS_NVR, the RTSP port is 554. If the HTTP Port is changed, when you add this device to GSurf or GS_NVR, please make sure the RTSP port number equals HTTP Port plus 2000. GXV3615WPI_HD And GXV3615W_HD Wifi Page – This page is only available for GXV3615W_HD and GXV3615WPI_HD Enable Wifi – Checked to enable Wifi SSID – Click on Scan to view available network. Choose a network and Click on Select to confirm. Security Mode – Choose associated Security mode. GXV3615WPI_HD Series DDNS Page Dynamic DNS provides devices that have a variable, often changing IP address with a well known hostname resolvable by network applications through standard DNS queries.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 17 of 30 Grandstream Networks, Inc. 02/10/12 Set up DDNS 1. Apply for a domain name from your service provider. 2. Login to the web configuration page, click Basic Settings > DDNS. 3. Enter the required information DDNS Active – If you want to use DDNS, please set this field to “Enabled” . DDNS ISP Type – Select your DDNS ISP Type. Self-Define DDNS Address – Self-define the DDNS server instead of using DDNS ISP Type. Site Name – The DDNS name for your device. DDNS Account/ DDNS Password – The account and password from the DDNS Provider. STUN Server – If the device is behind a router, a STUN server is needed to help penetrate the NAT. 4. Click Save to save the changes. You might need to reboot the device to apply all the changes. GXV3615WPI_HD Series SIP Page The GXV3615WPI_HD has the ability to receive phone calls and make phone calls when an alarm event is triggered through motion detection or alarm input. Register the GXV3615WPI_HD to a SIP server to enable the product to make and receive phone calls. To make outgoing phone calls out, the user needs to configure the Phone List properly. Register GXV3615WPI_HD to a SIP Server 1. From the GXV3615WPI_HD home page, click Basic Settings > SIP. 2. Go to SIP Settings Tab. 3. General Phone Settings. Registered – The field shows the registration status of the account with the SIP server. Unregister On Reboot – If it’s checked, the SIP user’s registration information will be cleared from the server when the phone reboots. 4. Enter the required information. Account Name – The field configures the SIP account name. SIP Server – The SIP Server’s IP address or Domain name provided by your service provider. Outbound Proxy – The IP address or Domain name of the Outbound Proxy, Media
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 18 of 30 Grandstream Networks, Inc. 02/10/12 Gateway, or Session Border Controller. Used for firewall or NAT penetration in different network environments. If the system detects a symmetric NAT, STUN will not work. ONLY outbound proxies can provide a solution for a symmetric NAT. SIP User ID – User account information provided by your service provider (ITSP); this is either an actual phone number or is formatted like one. Authenticate ID – The SIP service subscriber’s Authenticate ID used for authentication. It can be identical to or different from the SIP User ID. Authenticate Password – The SIP service subscriber’s account password for the GXV to register to the SIP server of the ITSP. STUN Server – If the device is behind a router, a STUN server is needed to help penetrate the NAT. Stream – To choose between Primary and Secondary stream. Preferred Vocoder – To choose different Vocoder type. Registration Expiration – This parameter allows users to specify the time frequency (in minutes) in which the GXV refreshes its registration with the specified registrar. The default interval is 60 minutes. Local SIP Port – This parameter defines the local SIP port used to listen and transmit. The default value is 5060. Local RTP Port – This parameter defines the local RTP-RTCP port pair that is used to listen and transmit. The default value is 5004. 5. Click Save to save all the changes. You need to restart the device to apply all changes. Configure Phone List To make sure the GXV3615WPI_HD can make phone calls to the number you preferred when alarm is triggered. You need to add number to the phone list. Steps to add phone number: 1. From the GXV3615WPI_HD home page, click Basic Settings > SIP. 2. Go to Phone List Tab. 3. Enter the Phone number and name, click Add a Number to save all the changes. 4. Numbers added to the system will be listed in this page.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 19 of 30 Grandstream Networks, Inc. 02/10/12 NOTE: With current firmware, only the first phone number in the list will be called when an alarm is triggered. GXV3615WPI_HD Series Status Page System Statistics System Statistics lists hardware and software information, for example, the part number, the software version, about the GXV3615WPI_HD. Hardware Version – This field contains the product’s hardware information. Part Number – This field contains the product part number information. Bootloader Version – Bootloader code version number. Core Version – Core code version number. Base Version – Base code version number. Firmware Version – Firmware code version number. System Up Time Since – This field shows the system up time since the last reboot. Network Status MAC Address – The device ID, in HEXADECIMAL format. LAN IP Address – This field shows the LAN IP address of the GXV3615WPI_HD. LAN Subnet Mask – This field shows the LAN subnet mask of the GXV3615WPI_HD. LAN Default Gateway – This field shows the Available phone numbers
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 20 of 30 Grandstream Networks, Inc. 02/10/12 LAN default gateway of the GXV3615WPI_HD. DDNS Status – This field shows the status of DDNS. Camera Type This section shows the Lens information of GXV3615WPI_HD. The Lens type information contains the brand name, the size of image sensor, the resolution and so on. GXV3615WPI_HD Series User Management Page All current users will be list in the User List section of this page. You can also add and remove users here. Existing User Name –The field lists all of the current users. You can insert or remove users from the list by click on the Add or Update or Delete button. User Name / Password – The user name and password required to login. Privilege – The privilege for the user to access to configuration page. Allow Anonymous Login – If ‘Allow Anonymous Login’ is set to Yes, no user name and password are required to login to the GXV3615WPI_HD web configuration pages. If you login anonymously, you will not be able to change any settings. GXV3615WPI_HD Series Maintenance Page Server Maintenance Restart – Click this button to restart the GXV3615WPI_HD. Restore – Click this button to perform a partial factory reset (The IP address will not be cleared) .
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 21 of 30 Grandstream Networks, Inc. 02/10/12 Firmware Upgrade and Provisioning Items Upgrade via – This field lets you choose the firmware upgrade method. The GXV3615WPI_HD supports HTTP, HTTPS and TFTP. Firmware Server Path – The IP address or domain name of the firmware server (the location of the firmware files) . Automatic Upgrade Interval – Enter the frequency (in minutes) in which the HTTP/HTTPS/TFTP server will be checked for new firmware upgrades or configuration changes. Automatic Upgrade – The default setting is “No.” Choose “Yes” to enable automatic. HTTP/HTTPS/TFTP upgrade and provisioning. When set to “No”, the IP Camera will only perform a HTTP/HTTPS/TFTP upgrade and perform a configuration check once during the boot process. Performing a firmware upgrade: 1. Download the firmware package from http://www.grandstream.com/firmware.html. 2. Unzip the firmware package and copy the files to the firmware upgrade server directory. Upgrades are supported via TFTP, HTTP and HTTPS. 3. Log in to the Maintenance page of the GXV3615WPI_HD. Select the server type from the dropdown list under the “Upgrade Via” field. Enter your server’s root directory in the “Firmware Server Path” field. 4. Reboot the GXV3615WPI_HD to begin the firmware upgrade process. GXV3615WPI_HD Series SMTP Page The SMTP server is used to send out emails when an alarm event or motion detection is triggered. The SMTP settings must be configured to make sure the alarm email is sent out properly. SMTP Server Settings Enable SMTP – Checked to enable SMTP SMTP Server – The IP or hostname of the SMTP server, for example, smtp.gmail.com. SMTP Server Port – The port of the SMTP server. The GXV3615WPI_HD supports port 25 and SSL
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 22 of 30 Grandstream Networks, Inc. 02/10/12 port 465, which is for SMTP with an encrypted connection. From E-Mail Address – The email address that sends out the alarm email(s). To E-Mail Address – The email addresses that the alarm email(s) will be sent to. You can have up to 3 emails configured. User Name/ Password – The user name and password required to log in to your SMTP server, for example, 123@gmail.com/123. SSL – Checked if the SMTP server requires a secure connection. Test Email Account Settings – Click the Test button to send a test email from the From E-Mail to the To E-Mail to make sure that SMTP is configured properly. If the receiver can get the test email, then the SMTP settings are ready to go. GXV3615WPI_HD Series FTP Page The FTP server is used to store video files if you configure the GXV3615WPI_HD to record video and upload it to the FTP server when an alarm event or motion detection is triggered. FTP Settings Enable FTP – The default setting is “No,” if you want the GXV3615WPI_HD to upload the recorded video to the FTP server when an alarm is triggered, set this field to “Yes.” FTP Server – The IP address or hostname of the SMTP server, ie. ftp.myserver.com. FTP Server Port – The port that your FTP server is using. User Name / Password – The user name and password required to log into your FTP server Path – The directory in the FTP server where recorded video will be uploaded. Test FTP Account Settings – Click the Test button to upload a sample file to make sure that FTP is properly configured. GXV3615WPI_HD Series Motion Detection Page The GXV3615WPI_HD supports Motion Detection. To utilize this feature, please follow the below steps: 1. Setup the motion detection monitored area. 2. Configure the motion detection time schedule. 3. Configure alarm action properly.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 23 of 30 Grandstream Networks, Inc. 02/10/12 Setup Motion Detection Monitored Area Enable Motion Detection – If this option is selected, motion detection will be enabled. If something/somebody moves in the motion detection region, an alarm will be triggered. Show Motion Detection Regions – If this option is selected, the motion detection regions will be displayed on the screen with a white border. To Edit a Monitored Area 1. In the Select a Region dropdown list, select the region ID. 2. Click Edit. 3. Click on the video, drag and draw you preferred area. 4. Set the Sensitivity. Click the Save button to save the sensitivity. NOTE: The Sensitivity value varies from 0 to 100. The larger the value is, the higher the sensitivity. 5. Click Save to save the settings. To Remove a Monitored Area 1. In the Select a Region dropdown list, select the region you would like to remove. 2. Click Remove. 3. Click Save to save the changes. Configure Motion Detection & Alarm Actions An alarm action is what the GXV3615WPI_HD is going to do when an alarm is triggered during the defined time period – the time schedule. The Button to save sensitivity only The white border for Motion Detection Regions NOTE: If Upload to Alarm center is checked for Alarm Actions, the white border will flash red when a motion detection alarm is triggered.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 24 of 30 Grandstream Networks, Inc. 02/10/12 GXV3615WPI_HD allows multiple alarm actions. Configure Motion Detection Time Schedule This section allows you to configure the time during which the GXV3615WPI_HD will monitor the motion detection. The GXV3615WPI_HD not only can monitor your settings but also can take actions when the alarm is triggered. GXV3615WPI_HD Series System Log This page is used to set up the system log server path and system log level. Once they are correctly configured, the device will send out system log messages to the system log server, which will help perform troubleshooting. Syslog Server – The IP address or URL of System log server. Syslog Level – Select the device to report the log level. Default is None. The level is one of Debug, Info, Warning or Error. Dropdown list for date Available time schedules Monitored region
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 25 of 30 Grandstream Networks, Inc. 02/10/12 IP VIDEO SURVEILLANCE FAQ 1. What is the default IP address of GXV3601/3501/3504? Prior to firmware version 1.0.3.9, the IP address of GXV3501/ 3504/ 3601/ 3611 is 192.168.1.168 at the factory default settings. You can perform a factory reset by pressing the RESET button on the device for 7 seconds. Starting from firmware version 1.0.3.9, the default IP configuration is DHCP. 2. Why can I not view the live video stream in Microsoft Internet Explorer? Please check whether the IE add-on is installed correctly. Once you log into the GXV3501/ 3504 / 3601 / 3615’s web interface Internet Explorer will indicate that “This website wants to install to following add-on: ‘GSViewer. cab’ from Grandstream Networks, Inc.”. Please install this add-on when prompted by IE. 3. How do you manually uninstall the Grandstream video viewer add-on for IE? Please follow these steps to uninstall the add-on: 1. Delete the GSViewerX Control from C:\WINDOWS\Downloaded Program Files directory 2. Delete GSNetClient.dll, GS_Replay.exe, GSViewerX.ocx, hi_h264dec_w.dll, lik_VoiceEngine_dll.dll and GSViewerX.inf from C:\WINDOWS\system32 4. Why can’t I access the GXV3501/ 3504/ 3601/ 3615 web configuration interface? Q 1: Is your internet service down? A 1: Connect a PC to the internet to test the connection. Q 2: Are the PC and the device in different subnets? A 2: Check the subnet mask and default gateway of the device and PC. Q 3: Is there a conflict with another IP address? A 3: Try to change the IP address of the device. Q 4: Has the HTTP port been changed? A 4: Contact the administrator of the device for more information. 5. The GXV3501/ 3504/ 3601/ 3615 web configuration page is not displayed correctly in Internet Explorer 8? In IE8, Compatibility View might need to be enabled for the GXV3501/ 3504/ 3601 web configuration page to load properly. To enable compatibility view, open IE8, click Tools, Compatibility View Setting, and add the GXV3501/ 3504/ 3601 web configuration pages to the Compatibility View.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 26 of 30 Grandstream Networks, Inc. 02/10/12 6. Why does IE indicate to install Grandstream Video Viewer add-on after a firmware upgrade? The add-on was properly installed before the firmware upgrade process. New firmware will often upgrade the add-on as well. To watch the live video stream, you must install the newest version of the add-on. 7. How do you watch secondary video stream? Login to the home page of the GXV3501/ 3504/ 3601/ 3615 web GUI, click Play to watch the video stream. To watch a secondary video stream, right click on the video, and select Secondary Stream on the pop-up menu. Try reinstalling the Grandstream Viewer add-on for IE if you cannot see the video stream. 8. Why is audio missing from the recorded video when an alarm is triggered? Please double check whether the device has an audio input connected. The GXV3504 has 4 audio input ports and one MIC IN port. The GXV3501 has a MIC IN port for an audio input. The GXV3601 has a built-in microphone and one MIC IN port for audio inputs. 9. What is DDNS? Is it important for IP surveillance product to have DDNS support? DDNS is an acronym for Dynamic Domain Name Service. It is important to choose an IP network camera that has DDNS support for dynamic IP addresses. Chances are that the network has a dynamic IP address (which changes with every log on). A DDNS service makes sure that the camera’s IP address always matches up to the current server address. DDNS also allows for a website to be linked to the IP camera that is constantly updated with the correct information and has a reliable feed. 10. Why is Windows Media Player unable to play the recorded videos files? The GXV3501/3601/3504 all use the H.264 video codec. Windows Media Player may lack the proper H.264 decoder to play the recorded video. Please download the Microsoft FFDShow H.264 decoder from http://sourceforge.net/projects/ffdshow-tryout/ and install it. 11. Alarm Triggered Events do not work in GSurf. Please double check the Alarm Action on your GXV3501/ 3504/ 3601. Login to the web GUI of the GXV3501/ 3504/ 3601, go to the Motion Detection or Alarm Events page, and make sure option Upload to Alarm Center is checked. 12. It is recommended that you save your video files in different directories when using GSurf and GS_NVR. GSurf and GS_NVR are different programs that have the ability to delete recorded video files. It is better to save video files in different directories when using GSurf and GS_NVR in the event that they automatically delete files that you might want to keep. 13. How can I use a cell phone to watch the GXV3501/ 3504/ 3601/ 3615 video stream?
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 27 of 30 Grandstream Networks, Inc. 02/10/12 You must set the video resolution to QCIF to watch the GXV3501/3504 /3601 video stream from a cell phone. Make sure to set the bit rate to 64kbps to ensure the best video quality. 14. Why doesn’t the IP address of the device reset when I click the “Restore” button on the Maintenance page? The GXV3501 /3504 /3601 could be installed in areas that are not easy to access. For example, it could be installed on the roof of a building or the ceiling of an office. This makes it difficult to reinstall the device, therefore the “Restore” function will not clear the IP address. Press the RESET button on the device for at least 6 seconds until you hear a beep to perform a factory reset of all parameters (including the IP address). 15. Why can’t the live video stream be viewed using a mobile phone or GSurf after changing the HTTP Port of the device? Make sure that the RTSP port of the device is set to 2000 plus the HTTP Port number. For example, if the HTTP port is 88, then the RTSP port of the device that you configured on GSurf / mobile phone should be 2088. 16. Some notes on using SD cards / USB drives. 1. The GXV3501/ 3504/ 3601 only supports FAT32 formatted USB drives 2. The GXV3501/ 3504/ 3601 support SD and SDHC 3. It takes 10-15 seconds to read SDHC and USB drives with large memory capacities. Please wait 15 seconds to unplug the SD/USB drive after you plug them into the device. 4. If there are many files (ie. 1800 or more image batch files) on the SD/USB drive, it can take up to 5 minutes to read them. Please do not refresh the web interface at this time as the GXV3501/3504 will restart reading the SD/USB drive. Grandstream is currently working on a fix for this issue. 5. Why is there a black / flashing bar at the bottom of the video feed? This can occur if the GXV3501 /3504 does not recognize the standard of the connected camera. If you experience this issue, please restart the GXV3501 /3504. The GXV3501 /3504 will detect the standard of the connected camera and use it when the GXV3501 /3504 boots up. To avoid this make sure to connect analog cameras before booting up the GXV3501 /3504. 6. Port forwarding Two ports must be forwarded on your router to watch video from a GXV3501 /3504 /3601/3611/ 3615 that is located on a private network from a PC in a public network. The web port (HTTP) and the RTSP port. Please make note that the RTSP port number changes according to the web port. If the web port is 80, then the RTSP port is 554. If the web port is not 80, then the RTSP port equals the web port +2000. For example, if the web port is 88, then the RTSP port will be 2088.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 28 of 30 Grandstream Networks, Inc. 02/10/12 7. Tested PC display adapters. Display Adapter Test Result SiS 650/651/740/661 FX/741/760 Series Works normally Intel(R) 82945R Express Chipset Family Works normally VIA/S3G UniChrome Pro IGP Works normally NIVDIA Geforce 7300GS Works normally SiS 661FX Works normally SiS Mirage Graphics Works normally SiS 661 Series Works normally Intel(R) G33/G31 Express Works normally SiS Mirage3 Graphics Works normally SiS 661FX/GX Mirage Graphics Works normally S3 Graphics ProSavageDDR(Microsoft Corporation) Works normally XGI Velari Z7/Z9/Z9S V1.08.12 There is some delay when playing videos. Intel 965 Express Chipset Family Works normally ATI Mobility Radeon X1300 Works normally Intel( R ) G45/G43 Express Chipset Works normally Mobile Intel 965 Express Chipset Family Works normally Mobile Intel(R) 4 Series Express Chipset Family Works normally Mobile Intel® 945GM Express Chipset Family Works normally Mobile intel® 915GM/GMS, 910GML Express Chipset Family Works normally Intel® G45/G43 Express Chipset Works normally ATI Technologies, RAGE XL PCI This display adapter cannot display videos.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 29 of 30 Grandstream Networks, Inc. 02/10/12 FCC Compliance Statement: This device complies with Part 15 FCC specifications, and operation complies with the following conditions :(1) The device may not cause harmful interference, and (2) The device must tolerate any interference, including interference could lead to misuse; FCC Caution: Any change on equipment by users without the permission will result in the losing the right to use the equipment; Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement: The transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Canadian Compliance Statement: This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
GXV3615WPI_HD IP Camera Series Firmware 1.0.4.8 Page 30 of 30 Grandstream Networks, Inc. 02/10/12 Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps. Professional installation instruction The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC15 C limit and is prohibited. Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. Instructions d'installation professionnelle En usage normal, afin de respecter les exigences reglementaires concernant l'exposition aux radiofrequences, ce produit doit etre installe de facon a respecter une distance de 20 cm entre l'antenne emettrice et les personnes. Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel depassant les niveaux limites definis par FCC 15 C, ce qui est interdit. Choisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales. EU Compliance Statement: The device complies with EU EMF Directive 1999/519/EC can be used in the European Community. “ Hereby, Grandstream Networks, Inc., declares that this (IP Camera ) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.” A copy of the EU Declaration of conformity is available on line at http://www.grandstream.com.cn/.

Navigation menu